The RFS-105 / RFS-108 is a high-performance Fast Ethernet switch, with all ports capable of 10 or 100Mbps auto-negotiation operation.

Transcription

1

2 The RFS-105 / RFS-108 is a high-performance Fast Ethernet switch, with all ports capable of 10 or 100Mbps auto-negotiation operation. Store-and-forward switching mode promises the low latency plus eliminates all the network errors, including runt and CRC error packets. To work under full-duplex mode, transmission and reception of the frames can occur simultaneously without causing collisions as well as double the network bandwidth. The switch is plug-n-play with no required software to configure and fully compliant with all kinds of network protocols. Moreover, the rich diagnostic LEDs on the front-panel can provide the operating status of individual port and whole system. RFS-105 Features: 5x 10/100Mbps RJ-45 Nway ports Supports 802.3az Green Ethernet: Detecting port usage power saving and cable length power saving Supports NWay protocol for speed (10/100Mbps) and duplex mode (Half/Full) auto-detection Supports MDI/MDI-X auto crossover Supports full and half duplex operation on all ports Supports back-pressure (half duplex) and flow control (IEEE 802.3x) Wire-speed packet filtering and forwarding rate Store-and-forward architecture filters fragment & CRC error packets Supports 1K MAC address entries in whole system 384K bits (48KB) buffer memory FCC Class B, CE 2

3 RFS-108 Features: 8 x 10/100Mbps RJ-45 Nway ports Supports 802.3az Green Ethernet: Detecting port usage power saving and cable length power saving Supports NWay protocol for speed (10/100Mbps) and duplex mode (Half/Full) auto-detection Supports MDI/MDI-X auto crossover Supports full and half duplex operation on all ports Supports back-pressure (half duplex) and flow control (IEEE 802.3x) Supports p QoS data management Wire-speed packet filtering and forwarding rate Store-and-forward architecture filters fragment & CRC error packets Supports 1K MAC address entries in whole system 768K bits (96KB) buffer memory FCC Class B, CE Before you start to install the switch, check the following contents in this package: A 5 port RFS-105 switch or a 8 port RFS-108 switch One external power adapter User s manual 3

4 Please refer to the following table for LED definition 5port 8port LED Status Operation Power Steady Green Power is on Off Power is off Link/Act Steady Green The port is connected Blinking Green The port is transmitting/receiving data. Off No connection Connect each station to the switch by twisted-pair cable. Plug one RJ-45 connector into a RJ-45 port of the switch, and plug the other RJ-45 connector into the station s network adapter. Power on the switch and then system is ready. For cable selection, refer to the following table. 4

5 In making a switch interconnection, you could use any port to connect another switch with straight or crossover cable. As all the ports support auto MDI / MDI-X function, using a straight cable to make a switch-to-switch connection is allowed. For cable selection, refer to the following table: Network Speed Cable Type Max. Length 10Mbps Cat. 3, 4, 5 UTP/STP 100 meters 100Mbps Cat. 5 UTP/STP 100 meters 5

6 RFS-105 Spec Switch Type Standards Desktop Ethernet, 802.3u Fast Ethernet, 802.3x Full-Duplex Flow Control, 802.3az Energy Efficient Ethernet Network Management Type Ports Speed MAC Address Table Buffer Memory Switching Method LEDs Power Dimensions Weight Temperature Humidity Unmanaged 5 x RJ45 10/100Mbps 1K 384K bits (48KB) Store and Forward System: Power Port: Link/Act External Power 5V0.6A 4.76" x 2.95" x 1.02" (121 x 75 x 26 mm) 0.57 lbs. (258.55g) 0ºC to 40ºC (32ºF to 104ºF) 10% - 90%, Non-condensing 6

7 RFS-108 Spec Switch Type Standards Desktop Ethernet, 802.3u Fast Ethernet, 802.3x Full-Duplex Flow Control, 802.3az Energy Efficient Ethernet, 802.1p QoS data management Network Management Type Ports Speed MAC Address Table Buffer Memory Switching Method LEDs Power Dimensions Weight Temperature Humidity Unmanaged 8 x RJ45 10/100Mbps 1K 768K bits (96KB) Store and Forward System: Power Port: Link/Act External Power 5V0.6A 6.08" x 2.95" x 1.02" (155 x 75 x 26 mm) 0.76 lbs. (345g) 0ºC to 40ºC (32ºF to 104ºF) 10% - 90%, Non-condensing 7

8 FCC Certifications This Equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received; including interference that may cause undesired operation. CE Mark Warning This equipment complies with the requirements relating to electromagnetic compatibility, EN class B for ITE, the essential protection requirement of Council Directive 2004/108/EC on the approximation of the laws of the Member States relating to electromagnetic compatibility. Company has an on-going policy of upgrading its products and it may be possible that information in this document is not up-to-date. Please check with your local distributors for the latest information. No part of this document can be copied or reproduced in any form without written consent from the company. Trademarks: All trade names and trademarks are the properties of their respective companies. Copyright 2012, All Rights Reserved. 8