NTP 162 Configure an I-211M-K or I-211M-L indoor ONT

Transcription

1 NTP 162 Configure an I-211M-K or I-211M-L indoor ONT NTP November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

2 I-220E-A 29 I-220E-A unit data sheet NTP 163 Install an I-220E-A indoor ONT NTP 164 Replace an I-220E-A indoor ONT NTP 165 Configure an I-220E-A indoor ONT Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

3 November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

4 29 I-220E-A unit data sheet 29.1 I-220E-A part numbers and identification I-220E-A general description I-220E-A software and installation feature support I-220E-A interfaces and interface capacity I-220E-A ONT LEDs I-220E-A detailed specifications I-220E-A GEM ports and T-CONTs I-220E-A power support I-220E-A functional blocks I-220E-A standards compliance I-220E-A special considerations Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

5 29 I-220E-A unit data sheet 29.1 I-220E-A part numbers and identification Table 29-1 provides identification information about I-220E-A indoor ONTs. Table 29-1 I-220E-A part numbers and identification Part number Mnemonic (1) Description CLEI CPR ECI/Bar code 3FE AB I-220E-A GPON I-series ONT, version A, asymmetric, BVM3M00CRA FE AE 2 POTS, 2 Ethernet. The AF variant provides a customer-specific logo on the enclosure. BVM4R10DRA FE AF 1AF AK The AC/DC power converter converts 120 V ac to 12 V dc and installs inside the customer residence. An Alcatel-Lucent approved power cable is required. 1AB Cable, AS 3112 plug to IEC C (1) connector, 3-conductor, 10 A, 250 V ac, 1.78 m, black (Australia/China) Note (1) See Chapter 2 Part numbers, ordering, and deployment configuration overview for product identification information I-220E-A general description The I-220E-A indoor ONT provides the subscriber interface for the network. The ONT terminates the PON interface and converts it to user interfaces that directly connect to subscriber devices. The ONT is compatible with all existing subscriber equipment, including analog phones with both tone and rotary dial capabilities, cordless phones, modems, fax machines, and caller ID boxes (Type I, Type II, and Type III). The I-220E-A indoor ONT provides the following functions: network demarcation for all services voice interworking function from the analog POTS lines to the VoIP/Ethernet layers interworking functions between the GEM and Ethernet layers interworking functions between the PON optical overlay and the RF video interface mux and demux functions to the PON optical to electrical conversion G984.4 standard and revised compliant OMCI interface for ONT management and provisioning 29-2 November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

6 29 I-220E-A unit data sheet 29.3 I-220E-A software and installation feature support Table 29-2 provides a list of software-based features and installation information supported by I-220E-A indoor ONTs. Table 29-2 I-220E-A ONT software feature support Features Chapter Cross reference for more information General ONT and MDU overview Service interface specifications ONT and MDU overview ONT and MDU general and interface technical specifications ONT and MDU general descriptions of features and functions Ethernet interface specifications POTS interface specifications Coaxial connectivity in the home and design guidelines Configuration recommendations 14 dbmv RF video receivers Services supported See the appropriate P-OLT user documentation for service creation procedures and descriptions. RSSI specifications Wi-Fi specifications Optical budget Location and installation options HTTP management Statistics and performance monitoring Supported UPS configurations ONT and MDU general and interface technical specifications How to install and replace an I-220E-A indoor ONT Information necessary to manage an ONT at a local site using an HTTP interface, CLI interface, CLI interface or butt set. ONT and MDU statistics and performance monitoring Part numbers, ordering, and deployment configuration overview ONT optical budget Install an I-220E-A indoor ONT Replace an I-220E-A indoor ONT ONT management using an ONT interface Performance monitoring statistics for Package A ONTs ONT and MDU to UPS or power adapter compatibility support 29.4 I-220E-A interfaces and interface capacity Table 29-3 describes the supported interfaces and interface capacity for I-220E-A ONTs. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

7 EOPT PON MGMT DATA RF TV 29 I-220E-A unit data sheet Table 29-3 I-220E-A ONT interface connection capacity ONT type and model Maximum capacity POTS 10/ 100/ BASE-T 10/ 100/ 1000 BASE-T RF video (CATV) MoCA VDSL2 DS1/ E1 Local craft GPON SC/ APC I-220E-A I-220E-A connections and components The I-220E-A ONTs are for indoor deployment and can be installed vertically, horizontally, or attached to a wall. There is a removable fiber access enclosure that covers an SC/APC connector and fiber splice tray. Connections to the RJ-45, and RJ-11 connectors are on the backside of the ONT. Figure 29-1 shows the physical connections for I-220E-A indoor ONTs. I-221E-A and I-220E-A use the same enclosure but each support different connections. A plastic plug covers the unavailable connector on the I-220E-A ONT. Figure 29-1 I-220E-A indoor ONT connections Ethernet ports RJ-11 phone connectors IP TV VOICE MODE LINK MODE LINK Fiber optic port Power connection Figure 29-2 shows the fiber storage tray and internal SC/APC connector November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

8 29 I-220E-A unit data sheet Figure 29-2 Fiber storage tray and internal SC/APC connector Buffer tube cable tie Buffer tube cable ties Fiber storage tray SC/APC connection Fiber cable tie Buffer tube routing flanges Fiber cable buffer tube Cable tie Fiber cable outer jacket Fiber routing flange No1009 Table 29-4 describes the I-220E-A indoor ONT physical connections. Table 29-4 I-220E-A indoor ONT connections Connection POTS connections Fiber optic port Ethernet ports Power Description This connection is provided through an RJ-11 phone connector. This connection is provided through a fiber optic cable. This connection is provided through an Ethernet RJ-45 cable. Up to four Ethernet connections are supported.the Ethernet port can support both data and in-band video services on all four interfaces. (1) This connection is provided through a cable to the ac/dc power converter. Note (1) Both Ethernet ports support IPTV but only one of the two ports can be configured for IPTV support at any one time. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

9 29 I-220E-A unit data sheet 29.5 I-220E-A ONT LEDs Figure 29-3 shows the I-220E-A indoor ONT LEDs. Figure 29-3 I-220E-A indoor ONT LEDs No1007 Table 29-5 lists I-220E-A indoor ONT LEDs. Table 29-5 I-220E-A indoor ONT LEDs Indicator LED color and behavior LED behavior description EQPT (1 of 2) Off Green solid Green flashing Red solid Amber solid Not powered Power available and battery is good Starting up ONT equipment failure Battery alarm 29-6 November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

10 29 I-220E-A unit data sheet Indicator LED color and behavior LED behavior description PON MGMT Data x IP_TV RF_TV (1) Off Green solid Green flashing Red solid Red flashing Amber solid Off Green solid Red solid Amber solid Green flashing Off Green solid Green flashing Red solid Off Green solid Green flashing Off Green solid Red solid Not powered PON is in service, ranged, and communicating to the ONT Ranging Loss of physical layer, startup failure, or link mismatch ONT disabled BIP errors detected Not established OMCI established ONT alarms present EMEA alarm present ONT disabled Not provisioned Service provisioned ONT Tx/Rx WAN (PON) ONT blocked and waiting for 802.1x authentication Not provisioned Joined at least 1 stream Receiving multicast IP video streams Not provisioned Provisioned and operating normally Provisioned but NOK (for example, low signal) When device is not connected to the PON and the Voice LED is configured using a country-specific XML file Voice (2) Off Red Green flashing periodic Green flashing patterned No SLID activity VoIP alarm 1 s on, 1 s off indicates SLID input mode and service is not provisioned The ONT is in SLID output mode and service is not provisioned When device is not connected to the PON and the Voice LED is not configured using a country-specific XML file Voice (2) Off Red Green solid Green flashing periodic Green flashing patterned No SLID service provisioned VoIP alarm No SLID service provisioned or registered, all lines on-hook 1 s on, 1 s off indicates SLID input mode or no SLID activity The ONT is in SLID output mode and service not provisioned When device is connected to the PON and the Voice LED is configured using a country-specific XML file Voice Red Green solid Green flashing periodic Off VoIP alarm Phone is on-hook; registered and provisioned 1 s on, 1 s off SIP provisioned and registered; phone off-hook or dialing Lines are on-hook, service not provisioned, or service is provisioned but not yet registered with the voice softswitch When device is connected to the PON and the Voice LED is not configured using a country-specific XML file Voice (2 of 2) Green flashing periodic Green solid Red 1 s on, 1 s at least one phone is off-hook or dialing All lines on-hook; registered and provisioned VoIP alarm Notes (1) The RF TV LED is only functional for RF video-equipped ONTs. (2) See SLID and LED behavior for a description of SLID output mode LEDs. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

11 29 I-220E-A unit data sheet Table 29-6 lists the RJ-45 LEDs on I-220E-A indoor ONTs. Table 29-6 I-220E-A indoor ONT RJ-45 LEDs Indicator LINK MODE LED color and behavior Off Green solid Green flashing Off Green solid Green flashing LED behavior description Link not detected Link active Link detected and activity present 10 Mb/s operation 100 Mb/s operation 1000 Mb/s operation 29.6 I-220E-A detailed specifications Table 29-7 lists the physical specifications for I-220E-A indoor ONTs. Table 29-7 I-220E-A indoor ONT physical specifications Dimensions Height Width Depth (excluding fiber storage tray) Weight [within ± 0.5 lb (0.23 kg)] Specifications 8.0 in. (20.32 cm) 9.0 in. (22.86 cm) 2.1 in. (5.33 cm) 4.0 lb (1.81 kg) Table 29-8 lists the power consumption specifications for I-220E-A indoor ONTs. Table 29-8 I-220E-A indoor ONT power consumption specifications Mnemonic Maximum power (Not to exceed) Condition Minimum power Condition I-220E-A 6.75 W 2 POTS off-hook, 2 Ethernet operational 4.5 W 2 POTS on-hook, other interfaces/services not provisioned Table 29-9 lists the environmental specifications for I-220E-A indoor ONTs. Table 29-9 I-220E-A indoor ONT environmental specifications Mounting method Temperature range and humidity Altitude Indoor 10/100BASE-T Ethernet ONTs (I-220E-A) (1 of 2) 29-8 November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

12 29 I-220E-A unit data sheet Mounting method Temperature range and humidity Altitude Desk or wall mounted (2 of 2) Operating: 32 F to 104 F (0 C to 40 C) ambient temperature 5% to 85% relative humidity, non-condensing Storage: 40 F to 158 F ( 40 C to 70 C) 5% to 95% relative humidly, non-condensing Maximum operating altitude ft (3048 m) above sea level Maximum non-operating altitude is ft ( m) above mean sea level 29.7 I-220E-A GEM ports and T-CONTs Table lists the maximum number of supported T-CONTs and GEM ports. Not all ONTs will be supported in all of the releases indicated the table. See the appropriate release Customer Release Notes for the most accurate list of supported devices. Table I-220E-A indoor ONT capacity for GEM ports and T-CONTs per package and release ONT or MDU Release Maximum Notes Package A ONTs GEM ports per indoor or outdoor ONT T-CONTs per indoor or outdoor ONT All are present: 20 are available, 2 are reserved for OMCI and debugging All are present: 21 are available, 1 is reserved for OMCI 29.8 I-220E-A power support The following power supply supports the I-220E-A indoor ONT. Click on the link for more information. Emerson 24 W AC/DC switching power adapter unit data sheet 29.9 I-220E-A functional blocks Table describes the supported interfaces for I-220E-A indoor ONTs. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

13 29 I-220E-A unit data sheet Table I-220E-A indoor ONT interfaces ONT category description Interface capacity POTS ports Ethernet ports RF video connectors POTS/ VDSL2 / 10/100/ 1000 BASE-T Ethernet connectors DS1/ E1 Single-residence indoor ONTs (I-220E-A) ONT SoC technology is an integrated system that provides the GPON, voice, and data (including IP video) subsystems. It provides two key connection functions: connecting the ONT to the GPON and the connecting the ONT to subscriber equipment. The voice subsystem supports RJ-11 ports, and the data and IP video subsystems support RJ-45 ports. The ONT connects to the GPON using a optical connector. The GPON connection performs a GPON transmission convergence (TC) layer function. The GPON signal from the P-OLT terminates at a diplexer. The diplexer is an optical module that performs optical and electrical conversion. The diplexer interfaces with the GPON MAC on the SoC. Figure 29-4 shows an ONT with a diplexer, four POTS, and two Ethernet ports. Figure 29-4 ONT with a diplexer Power Converter GPON Diplexer SOC POTS (4) Ethernet (2) RJ-11 RJ ONT SoC technology serves as the main hardware block for the I-220E-A indoor ONTs; see Figure November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

14 29 I-220E-A unit data sheet Figure 29-5 I-220E-A ONT hardware block POTS ports Control processor SoC DSP SoC Bridge Ethernet MACs GPON MAC Ethernet ports GPON ONT SoC technology consists of five key elements: GPON MAC The GPON MAC element on the SoC provides the GPON interface to the TC layer via the optical diplexer or triplexer (if using RF video). This interface supports the FSAN standards compliant GEM mode transport and provides AES, FEC, and data fragmentation functionality over the GPON as described in G (GPON TC Layer) ITU specification. Ethernet MAC The SoC provides an Ethernet PHY device (either 10/100BaseT or 10/100/1000BaseT) between the GMII interface and the RJ-45 port. Digital Signal Processor (DSP) interface The DSP provides voice processing and has a TDM interface to the CODEC/SLIC devices. control processor The control processor manages functions related to OMCI, IGMP, VoIP, and Ethernet services. SoC bridge The SoC bridge provides an integrated data channel between the Ethernet MAC, the GPON MAC, the DSP, the control processor, and the other integrated elements such as flash memory, SDRAM, the local bus controller, and the DUART interface to the craft port if used. These ONTs can also interact with additional hardware components to support functionality not provided by SoC technology. For example, MoCA and CES functionality require additional hardware support. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

15 29 I-220E-A unit data sheet I-220E-A standards compliance The I-220E-A indoor ONT is compliant with the following standards: G (revised) support for OMCI interface for ONT management and provisioning G support for Dynamic Bandwidth Allocation (DBA) G support for Forward Error Correction (FEC) in both upstream and downstream directions G984.4 (standard and revised) support for OMCI interface for ONT management and provisioning I-220E-A special considerations FEC is not supported on I-220E-A indoor ONTs. Upgrade considerations and limitations Existing ONTs that use 7342 ISAM FTTU releases older than R04.06.xx and R04.07.xx must be upgraded to use R software while assigned to a PON ID value smaller than 64. For this purpose, if split ratios larger than 1:64 are being deployed, you may choose to set aside the first PON ID as a staging point. I-220E-A ONT considerations and limitations Table lists the considerations and limitations for I-220E-A indoor ONTs. Table I-220E-A ONT considerations and limitations Considerations and limitations No support for per VLAN protocol downstream tagging mode In SVLAN cross-connect tunnel mode: use non-overlapping pbits since the use of the same pbits on two or more VLAN ports results in a mismatch alarm downstream frames sent with a single tag normally sent out on the user-side as untagged, will instead be sent as priority tagged When using CVLAN translation, or when the same queue is used for multiple pbits, the highest pbit value in the queue in the downstream direction will be selected to stomp the pbit in the packet Simultaneous configuration of a CVLAN port and an S-Tunnel on the same UNI will only be supported if these services are provisioned with non-overlapping pbits The same VLAN port must be used when employing both protocol-based VLAN for PPPoE and IPoE-based VLANs When the VLAN is translated, the pbit value must be modified and the highest pbit value is mapped to that GEM port When more than one Ethernet port is in VLAN translation mode, or set to flexible mode with IGMP channels created, the USERSIDE VLAN IDs of those services are different. All downstream multicast packets will be tagged on the UNI port with VLAN ID of 4094 Maximum use of multicast on 1 Ethernet port at a time (1 of 2) November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

16 29 I-220E-A unit data sheet Considerations and limitations For C forwarder and S+C CC forwarder, if the VLAN port uses regenerated profiles or regenerated pbits, then the downstream traffic can only flow with the derived pbits When either tip or ring is grounded, DGNONTPOTS tip to ground and ring to ground restrictive measurements are simultaneously reported as 0 ohms The ONT cannot forward CCM packets to the edge router The ONT does not support RIPv2 or SAPv1 packets on an unicast VLAN that is not the multicast GEM port The ONT cannot perform subscriber join IGMP CAC check when LT-to-ONT signalling is disabled (2 of 2) Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

17 29 I-220E-A unit data sheet November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

18 NTP 163 Install an I-220E-A indoor ONT Purpose This NTP provides the steps to install an I-220E-A indoor ONT. General The DLPs listed in this NTP describe the steps to install an I-220E-A indoor ONT. Prerequisites See the listed DLPs for prerequisites. Recommended tools You need the following tools for the installation: #2 Phillips screwdriver 1/4 in. (6 mm) flat blade screwdriver wire strippers fiber optic splicing tools RJ-45 cable plug crimp tool voltmeter or multimeter optical power meter wall mounting template drill and drill bits Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November 2013 NTP FE AAAA TCZZA Edition 01

19 NTP 163 Install an I-220E-A indoor ONT Safety information Read the following safety information before installing the unit. Danger 1 Always contact the local utility company before you connect the enclosure to the utilities. Danger 2 Observe the local and national laws and regulations that may be applicable to this installation. Warning This equipment is ESD sensitive. Proper ESD protections should be used when removing the fiber access cover of the indoor ONT. Caution Keep indoor ONTs out of direct sunlight. Prolonged exposure to direct sunlight can damage the unit. Procedure Note Observe the following: The indoor ONT should be installed in accordance with the applicable requirements of the NEC or CEC. Local authorities and practices take precedence when there is conflict between the local standard and the NEC or CEC. The indoor ONT must be installed by qualified service personnel only. Indoor ONTs must be installed with cables that are suitably rated and listed for indoor use. Use this procedure to install an I-220E-A indoor ONT. 1 Prepare the cables at the site where the ONT will be installed (DLP 100). 2 Review the connection locations shown in Figure NTP NTP November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

20 EOPT PON MGMT DATA RF TV NTP 163 Install an I-220E-A indoor ONT Figure NTP 163-1: I-220E-A indoor ONT connections Ethernet ports RJ-11 phone connectors IP TV VOICE MODE LINK MODE LINK Fiber optic port Power connection Install the AC power converter and connect the power cable to the ONT (DLP 106). 4 Connect the Ethernet, and POTS cables (DLP 101, DLP 123). 5 If used, configure the SLID (DLP 129). 6 Mount the indoor ONT and connect the fiber optic cables (DLP 135). 7 Verify the ONT LEDs (DLP 127). 8 Activate and test the services (DLP 128). 9 STOP. This procedure is complete. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November 2013 NTP FE AAAA TCZZA Edition 01

21 NTP 163 Install an I-220E-A indoor ONT NTP November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

22 NTP 164 Replace an I-220E-A indoor ONT Purpose This NTP provides the steps to replace an I-220E-A indoor ONT. General The DLPs listed in this NTP describe mounting and cabling for the I-220E-A indoor ONT. Prerequisites See the listed DLPs for prerequisites. Recommended tools You need the following tools for replacing the ONT: #2 Phillips screwdriver 1/4 in. (6 mm) flat blade screwdriver wire strippers fiber optic splicing tools RJ-45 cable plug crimp tool voltmeter or multimeter optical power meter wall mounting template drill and drill bits Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November 2013 NTP FE AAAA TCZZA Edition 01

23 NTP 164 Replace an I-220E-A indoor ONT Safety information Read the following safety information before installing the unit. Danger 1 Always contact the local utility company before you connect the enclosure to the utilities. Danger 2 Observe the local and national laws and regulations that may be applicable to this installation. Warning This equipment is ESD sensitive. Proper ESD protections should be used when removing the fiber access cover of the indoor ONT. Caution Keep indoor ONTs out of direct sunlight. Prolonged exposure to direct sunlight can damage the unit. Procedure Note Observe the following: The indoor ONT should be installed in accordance with the applicable requirements of the NEC or CEC. Local authorities and practices take precedent when there is conflict between the local standard and the NEC or CEC. The indoor ONT must be installed by qualified service personnel. Indoor ONTs must be installed with cables that are suitably rated and listed for indoor use. Use this procedure to replace an I-220E-A indoor ONT. 1 Deactivate the ONT services (DLP 131). If you are using the SLID feature, this step is not required. The ONT and the services can remain in service (IS). 2 At the subscriber site, locate the indoor ONT and disconnect the power, phone, Ethernet and fiber optic cables; see Figure NTP NTP November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

24 EOPT PON MGMT DATA RF TV NTP 164 Replace an I-220E-A indoor ONT Figure NTP 164-1: I-220E-A indoor ONT connections Ethernet ports RJ-11 phone connectors IP TV VOICE MODE LINK MODE LINK Fiber optic port Power connection Replace the indoor ONT with a new unit (DLP 157). 4 Reattach and connect the power cable to the ONT (DLP 106). 5 Reconnect the Ethernet and POTS connections (DLP 101, DLP 123). 6 If used, configure the SLID (DLP 129). Note A new SLID or the old SLID may be used with the replacement ONT. If a new SLID is used, the new SLID must also be programmed at the P-OLT using TL1 or a network manager. If the old SLID is used, no changes need to be made at the P-OLT. 7 Remove the empty plastic fiber storage tray from the new indoor ONT by lifting it up until it snaps free from the electronics enclosure. You can discard the storage tray or keep it as a spare. 8 Replace the full fiber storage tray by snapping it on the enclosure. Route the fiber cable and attach it with cable ties, as shown in Figure Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November 2013 NTP FE AAAA TCZZA Edition 01

25 NTP 164 Replace an I-220E-A indoor ONT Figure NTP 164-2: Indoor ONT fiber optic cable routing Buffer tube cable tie Buffer tube cable ties Fiber storage tray SC/APC connection Fiber cable tie Buffer tube routing flanges Fiber cable buffer tube Cable tie Fiber cable outer jacket Fiber routing flange No Remove the SC/APC adapter and pigtail connector dust plug and attach the fiber pigtail to the SC/APC connector. 10 If required, have approved service personnel who are trained to work with optic fiber clean the fiber optic connection. See DLP 134 for more information about fiber optic handling, inspection, and cleaning. Danger Fiber optic cables transmit invisible laser light. To avoid eye damage or blindness, never look directly into fibers, connectors, or adapters. 11 Route the pigtail using the fiber-bend, radius-limiting features built into the indoor ONT housing. NTP November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

26 NTP 164 Replace an I-220E-A indoor ONT 12 Connect the fiber optic cable to the fiber optic port shown in Figure NTP (DLP 135). Warning Be careful to maintain a bend radius of no less than 1.5 inches (3.8 cm) when connecting the fiber optic cable. Too small of a bend radius in the cable can result in damage to the optic fiber. 13 Verify the ONT LEDs, voltage status, and optical signal levels (DLP 127). 14 Activate and test the services (DLP 128). 15 STOP. This procedure is complete. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November 2013 NTP FE AAAA TCZZA Edition 01

27 NTP 164 Replace an I-220E-A indoor ONT NTP November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

28 NTP 165 Configure an I-220E-A indoor ONT General Please refer to the OLT Operations and Maintenance using TL1 and CLI guide for the software configuration procedure for I-220E-A indoor ONTs. For HTTP configuration procedures, please refer to chapter 6, ONT management using an ONT interface. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November 2013 NTP FE AAAA TCZZA Edition 01

29 NTP 165 Configure an I-220E-A indoor ONT NTP November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

30 I-240E-P 30 I-240E-P unit data sheet NTP 166 Install an I-240E-P indoor ONT NTP 167 Replace an I-240E-P indoor ONT NTP 168 Configure an I-240E-P indoor ONT Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

31 November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

32 30 I-240E-P unit data sheet 30.1 I-240E-P part numbers and identification I-240E-P general description I-240E-P software and installation feature support I-240E-P interfaces and interface capacity I-240E-P LEDs I-240E-P detailed specifications I-240E-P GEM ports and T-CONTs I-240E-P power support I-240E-P functional blocks I-240E-P standards compliance I-240E-P special considerations Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

33 30 I-240E-P unit data sheet 30.1 I-240E-P part numbers and identification Table 30-1 provides part numbers and identification information for I-240E-P indoor ONTs. Table 30-1 I-240E-P part numbers and identification Mnemonic Ordering kit part number Provisioning part number Description CLEI CPR ECI/ Bar code I-240E-P 3FE AH (customerspecific logo) 3FE AA GPON I-series ONT, version P, 2 POTS and 4 GigE Ethernet interfaces.includes ac/dc power cord with Australian (AU) variant plug and fiber storage tray I-240E-P general description The I-240E-P indoor ONTs provide a subscriber interface for the network by terminating the PON interface and converting it to user interfaces that directly connect to subscriber devices. The ONT is compatible with all existing subscriber equipment, including analog phones with both tone and rotary dial capabilities, cordless phones, modems, fax machines, and caller ID boxes (Type I, Type II, and Type III). These indoor ONTs provide the following functions: fully G.984 series GPON standard compliant G984.4 and G standard compliant ONT Management Control Interface (OMCI) interface for ONT management and provisioning Management Information Base (MIB) manipulation over OMCI by Create, Delete, Set, Get, and Get next commands optics that support received signal strength indication (RSSI) remote software image download (as well as activation and reboot) over OMCI performance monitoring as well as alarms and AVC reports IGMP snooping delivers video content in the form of data by multicast or unicast support for Multicast GEM port 30.3 I-240E-P software and installation feature support Table 30-2 provides a list of software-based features and installation information supported by I-240E-P indoor ONTs November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

34 30 I-240E-P unit data sheet Table 30-2 I-240E-P indoor ONT software feature support Features Chapter Cross reference for more information General ONT and MDU overview Service interface specifications RSSI specifications General information common to multiple devices and an explanation of general system behaviors. ONT and MDU general and interface technical specifications ONT and MDU general and interface technical specifications ONT and MDU overview Ethernet interface specifications POTS interface specifications RSSI specifications Wi-Fi specifications Optical budget Location and installation options ONT and MDU general and interface technical specifications How to install and replace I-240E-P indoor ONTs ONT optical budget Install an I-240E-P indoor ONT Replace an I-240E-P indoor ONT Activation method ONT and MDU overview ONT activation and behavior using SLID HTTP ONT management procedures Statistics and performance monitoring Supported UPS Information necessary to manage an ONT at a local site using an HTTP interface, CLI interface, CLI interface, or butt set. ONT and MDU statistics and performance monitoring Part numbers, ordering, and deployment configuration overview ONT management using an ONT interface Performance monitoring statistics for Package C ONTs ONT and MDU to UPS or power adapter compatibility support 30.4 I-240E-P interfaces and interface capacity Table 30-3 describes the supported interfaces and the maximum connection capacity for I-240E-P indoor ONTs. Table 30-3 I-240E-P indoor ONT interface connection capacity ONT type and model Maximum capacity POTS 10/ 100 BASE-T 10/ 100/ 1000 BASE-T RF video (CATV) MoCA VDSL2 DS1/E1 Local craft GPON SC/APC I-240E-P The I-240E-P indoor ONTs are for indoor deployment and can be installed horizontally on a flat surface as well as attached to a wall. These indoor ONTs come equipped with a removable fiber access tray for storing excess cable as well as a Reset button. Figure 30-1 shows the connections for I-240E-P indoor ONTs. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

35 30 I-240E-P unit data sheet Figure 30-1 I-240E-P indoor ONT physical connections POWER OPTICAL LAN UPDATE ALARM POTS GE1 GE2 GE3 GE4 POTS1 POTS2 RESET PWR Ethernet ports (RJ45) POTS ports (RJ-11) Fiber optic connector Power connector Reset button Table 30-4 describes the physical connections on I-240E-P indoor ONTs. Table 30-4 I-240E-P indoor ONT physical connections Connection (1) Ethernet ports POTS Power Fiber optic Description This connection is provided through Ethernet RJ-45 cables. Up to four 10/100 Base-T Ethernet interfaces are supported.the Ethernet ports can support both data and in-band video services on all four interfaces. This connection is provided through RJ-11 ports. Up to two POTS connections are supported.the POTS ports support voice services. This connection is provided through the power connector. A power cable fitted with a barrel connector is used to make the connection. This connection is provided through a SC/APC fiber optic connector. The fiber optic connector is located behind a fiber optic port cover on these ONTs. Note (1) The primary path for the earth ground for these ONTs is provided by the 12V Return signal in the power connector I-240E-P LEDs Figure 30-2 shows the I-240E-P indoor ONT LEDs November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

36 OPTICAL LAN UPDATE ALARM POTS POWER 30 I-240E-P unit data sheet Figure 30-2 I-240E-P indoor ONT LEDs POWER OPTICAL LAN UPDATE ALARM POTS Table 30-5 provides I-240E-P indoor ONT LED descriptions. Table 30-5 I-240E-P indoor ONT LEDs Indicator LED color and behavior LED behavior description POWER OPTICAL LAN UPDATE ALARM POTS Off Green solid Green flashing Red solid Green solid Green flashing Off Green solid Green flashing Off Green flashing Red solid Off Red solid Red flashing Green solid Off Green solid Green flashing No power Operating on ac power ONT is starting up Optical interface abnormal (LOS/LOF) ONT working normally ONT in ranging and synchronization process No Ethernet link is up or the ONT is not ready to run Ethernet service At least one Ethernet link on the ONT is up At least one Ethernet links on the ONT is up and is either receiving or transmitting data No software update ONT software update underway ONT software update failure ONT is operating without failure ONT hardware is out of order ONT software failure No alarm with local access enabled No POTS provisioned (all phones are on-hook or no phones connected) or the ONT is not ready to run POTS service One or more phones are off-hook One or more phones are off-hook for a minimum of one hour Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

37 30 I-240E-P unit data sheet 30.6 I-240E-P detailed specifications Table 30-6 lists the physical specifications for I-240E-P indoor ONTs. Table 30-6 I-240E-P indoor ONT physical specifications Dimensions Height Width Depth Specifications 5.1 in. (13 cm) 6.8 in. (17.2 cm) 1.3 in. (3.3 cm) Weight [within ± 0.5 lb (0.23 kg)] 1.1 lb (500 g) Table 30-7 lists power consumption specifications for I-240E-P indoor ONTs. Table 30-7 I-240E-P indoor ONT power consumption specifications Mnemonic Maximum power (not to exceed) Condition Minimum power Condition I-240G-P 9 W 2 POTS off-hook, 4 E operational 4.5 W 2 POTS on-hook, other interfaces/services not provisioned Table 30-8 lists the environmental requirements for I-240E-P indoor ONTs. Table 30-8 I-240E-P indoor ONT environmental requirements ONT type Mounting method Temperature range and humidity Altitude Desk or wall mounted Operating: 32 F to 104 F (0 C to 40 C) ambient temperature 10% to 90% relative humidity, non-condensing Storage: Contact your Alcatel-Lucent support representative for more information Contact your Alcatel-Lucent technical support representative for more information 30.7 I-240E-P GEM ports and T-CONTs Table 30-9 lists the maximum number of supported T-CONTs and GEM ports for I-240E-P indoor ONTs. Not all ONTs will be supported in all of the releases indicated the table. See the appropriate release Customer Release Notes for the most accurate list of supported devices November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

38 30 I-240E-P unit data sheet Table 30-9 I-240E-P indoor ONT capacity for GEM ports and T-CONTs per package and release ONT or MDU Release Maximum Notes Package C ONTs GEM ports per indoor or outdoor ONT R to R are present: 10 are available, 2 are reserved for multicast and debugging R x, R , R , R R x, R x, R x, R x, R x are present: 30 are available, 2 are reserved for multicast and debugging 30 R x 30 T-CONTs per indoor or outdoor ONT R to R are present: 6 are available, 1 is reserved for OMCI R x, R , R , R R x, R x, R x, R x, R x, R x R x, R x, R x, R are present: 15 are available, 1 is reserved for OMCI are present: 31 are available, 1 is reserved for OMCI 30.8 I-240E-P power support See Part numbers, ordering, and deployment configuration overview for the specific power supplies supported by the I-240E-P indoor ONT I-240E-P functional blocks I-240E-P indoor ONTs transmit Ethernet packets to four RJ-45 Ethernet ports and voice traffic to two RJ-11 POTS ports. ONT SoC technology serves as the main hardware block for I-240E-P indoor ONTs; see Figure Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

39 30 I-240E-P unit data sheet Figure 30-3 I-240E-P ONT hardware block POTS ports Control processor SoC DSP SoC Bridge Ethernet MACs GPON MAC Ethernet ports GPON ONT SoC technology consists of five key elements: GPON MAC The Gigabit Passive Optical Network Media Access Control (GPON MAC) element on the SoC terminates the GPON interface using an optical diplexer. This interface supports GPON as described in G (GPON TC Layer) ITU specification. Ethernet MAC The SoC provides up to four GE MACs. DSP interface The Digital Signal Processor (DSP) provides voice processing for 2 POTS lines with the 3-way calling. The DSP has a dedicated 64 kbyte instruction cache and shares a 32 kbyte data cache with the Control Processor. Control Processor The Control Processor features an integral memory management unit that supports a dedicated 64 kbyte instruction cache and shares a single 32 kbyte data cache with the DSP. The Control Processor and DSP also include a single channel Data Management Application (DMA) controller with a 4 kbyte read ahead low-latency Dynamic Random Access Memory (DRAM) access port. The processors typically run at 400 MHz. Switch matrix The Switch matrix provides an integrated data channel between the four GE MACs, the GPON MAC, the MoCA MAC, the DSP, the control processor, and the other integrated elements such as flash memory, DRAM, and the local bus controller. These ONTs can also interact with additional hardware components to support functionality not provided by the SoC technology November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

40 30 I-240E-P unit data sheet Single-residence Ethernet Package C ONTs with POTS and with or without RF video Single-residence Ethernet ONTs with POTS and with or without RF video represent one variation of the Package C ONT. In the case of these ONTs, RF video ports may or may not be available in addition to POTS and Ethernet ports. I-240E-P indoor Package C ONTs transmit Ethernet packets on four RJ-45 Ethernet ports and voice traffic on two RJ-11 POTS ports. These ONTs also feature fiber optic and power connectors. Figure 30-4 shows the functional blocks for a Package C ONT with Ethernet, POTS, and coaxial ports. Of course, the I-240E-P indoor ONT does not have a coaxial port. For those ONTs with less than the maximum number of Gigabit Ethernet or POTS ports, the excess ports are blocked by a plastic cover. Figure 30-4 Single-residence Ethernet ONT with POTS and with or without RF video (diplexer) Power Converter Power connector GPON Optical block SOC POTS (4/2/1) Ethernet (4/2) RJ-11 RJ-45 RF Video Amp Diplexer F-type connector I-240E-P standards compliance The I-240E-P indoor ONTs are compliant with the following standards: 802.1d support for bridging 802.1p support for mapping and mapper service profile on U/S 802.1p support for marking and remarking 802.1p support for Class of Service based on VLAN-ID 802.1q support for virtual switch based on VLAN G.711 support for FAX, modem connection, and TTY devices G.984 support GPON interface (framing) G support for Amd1, Class B+ G support for activation and password functions G support for FEC in both upstream and downstream directions G support for multicast using a single GEM Port-ID for all video traffic G984.4 and G support for OMCI interface for ONT management and provisioning G support for blocking filter as an option Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

41 30 I-240E-P unit data sheet I-240E-P special considerations Upgrade considerations and limitations Existing ONTs that use 7342 ISAM FTTU releases older than R04.06.xx and R04.07.xx must be upgraded to use R software while assigned to a PON ID value smaller than 64. For this purpose, if split ratios larger than 1:64 are being deployed, you may choose to set aside the first PON ID as a staging point. I-240E-P ONT considerations and limitations Table lists the considerations and limitations for these ONTs. Table I-240E-P indoor ONT considerations and limitations Considerations and limitations Support for up to 32 GEM ports per Ethernet UNI Support for 7 T-CONTs including the OMCI T-CONT Ethernet OAM (802.1 ag) is not supported TPID overwrite is not supported Anti-spoofing is supported on I-020G-P and I-120G-P ONTs by treating PPPoE packets in the same manner as IPoE packets when anti-spoofing is configured. Other ONTs do not support anti-spoofing x is not supported IGMPv3 snooping with SSM is not supported VLAN translation is supported prior to replication for downstream IPTV multicast. The same VLAN operation must be provisioned for all Ethernet UNIs participating in IPTV multicasting The ONT will not support sending some untagged multicast frames through one Ethernet UNI while sending other tagged multicast frames through another Ethernet UNI Double-tagged frames are not supported Flow control is not supported. The ONT will not generate PAUSE frames for the client if there is traffic congestion Configurable Ethernet for VLAN tag detection is not supported. Currently, only 0x8100 is supported POTS pull-break-dial-tone (PBDT) is not supported for SIP, H.248, and G6 Call history data collection (ONTCALLHST) is not supported G.729 and G.711 a/u are supported while G codec is not supported Only one global DSCP to pbit mapping table is supported Default Ethernet flow and wildcard Ethernet flow coexisting on the same Ethernet port is not supported Maximum of 16 service flows (VLANs) can be enabled with pbit translation (1 of 2) November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

42 30 I-240E-P unit data sheet Considerations and limitations Non-supported call services: Direct connect Warm line Call forward status indications Home Intercom Call park Bridged line Call pickup with barge-in Suppressed ringing Service classification by Ethertype is not supported The first time an ONT is connected, the initial Ethernet UNI is enabled by default. This Ethernet UNI can be disabled by the OLT When pbit translation is enabled, each GEM port can only translate into one pbit. Mapping downstream Pbits to different GEM ports is the only form of supported pbit translation Static multicast is not supported IPTV multicast over PPPoE (from the multicast port) is not supported PM counter is partially supported Pbit translation following DSCP to pbit mapping is not supported Pbit translation when a UNI is set to pass through any VLAN ID (unisidevlan=4096 and networksidevlan=4096) is not supported Packet loss occurs in 1G wirespeed. Due to the additional 4-byte routing tag, throughput is less than 1G for all packet lengths Weighted round robin (WRR) is not accurate when configured with OMCI because the weight definition in the device is the reverse of OMCI definition For WRR scheduling, bandwidth not used by a queue can not be claimed by any other queues Up to eight extended VLAN rules per VLAN port is supported AES key can not be changed locally on an ONT As of R and later, the ONT supports stacked VLAN ibridges mode. With a stacked VLAN ibridge, in addition to performing bringing operations, the ONT supports when the ISAM can add/remove a VLAN header to customer upstream or downstream traffic, which allows support for different broadband access solutions. (2 of 2) Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

43 30 I-240E-P unit data sheet November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

44 NTP 166 Install an I-240E-P indoor ONT Purpose This NTP provides the steps to install I-240E-P indoor ONTs. General The DLPs listed in this NTP describe mounting and cabling for I-240E-P indoor ONTs. Prerequisites See the listed DLPs for prerequisites. Recommended tools You need the following tools for the installation: #2 Phillips screwdriver 1/4 in. (6 mm) flat blade screwdriver wire strippers fiber optic splicing tools RJ-45 cable plug crimp tool voltmeter or multimeter optical power meter wall mounting template drill and drill bits Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November 2013 NTP FE AAAA TCZZA Edition 01

45 NTP 166 Install an I-240E-P indoor ONT Safety information Read the following safety information before installing the unit. Danger 1 Contact the local utility company before you connect the enclosure to the utilities. Danger 2 Observe the local and national laws and regulations that may be applicable to this installation. Danger 3 If the coaxial output of the ONT is connected to the dwelling infrastructure coaxial distribution system, ensure that the coaxial distribution system is separately grounded. Grounding of the dwelling coaxial infrastructure shall use Listed grounding devices and must be installed in accordance with local Codes and Article 800 of the National Electric Code, ANSI/NFPA 70, following the manufacturers instructions. Warning This equipment is ESD sensitive. Proper ESD protections should be used when removing the fiber access cover of the indoor ONT. Caution Keep indoor ONTs out of direct sunlight. Prolonged exposure to direct sunlight can damage the unit. Procedure Note Observe the following: The indoor ONT should be installed in accordance with the applicable requirements of the NEC or CEC. Local authorities and practices take precedent when there is conflict between the local standard and the NEC or CEC. The indoor ONT must be installed by qualified service personnel. Indoor ONTs must be installed with cables that are suitably rated and listed for indoor use. See I-240E-P detailed specifications in the unit data sheet for the temperature ranges for this ONT. Use this procedure to install an I-240E-P indoor ONT. 1 Prepare the cables at the site where the ONT will be installed (DLP 100). 2 Locate any missing cables and route them to the ONT as per local practices. NTP November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

46 OPTICAL LAN UPDATE ALARM POTS POWER NTP 166 Install an I-240E-P indoor ONT 3 Place the indoor ONT unit: a On the flat surface, such as a desk, horizontally resting on its four feet as shown in Figure NTP 166-1; go to step 4. Figure NTP 166-1: I-240E-P indoor ONT on a desk b On a wall (DLP 122). 4 Review the connection locations as shown in Figure NTP for I-240E-P indoor ONTs. Figure NTP 166-2: I-240E-P indoor ONT connections POWER OPTICAL LAN UPDATE ALARM POTS GE1 GE2 GE3 GE4 POTS1 POTS2 RESET PWR Ethernet ports (RJ45) POTS ports (RJ-11) Fiber optic connector Power connector Reset button Connect the Ethernet cables to the RJ-45 ports (DLP 101). 6 Connect the POTS cables to the RJ-11 ports (DLP 123). 7 Connect the SC/APC fiber optic cable (DLP 125). Warning Be careful to maintain a bend radius of no less than 1.5 inches (3.8 cm) when connecting the fiber optic cable. Too small of a bend radius in the cable can result in damage to the optic fiber. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November 2013 NTP FE AAAA TCZZA Edition 01

47 NTP 166 Install an I-240E-P indoor ONT 8 Install the power supply according to manufacturer specifications. Note Observe the following: Units must be powered by a Listed or CE approved and marked limited power source power supply with a minimum output rate of 12 V dc, 1.25 A. 9 Connect the power cable to the power connector. 10 If used, configure the SLID (chapter 6). 11 Verify the ONT LEDs, voltage status, and optical signal levels (DLP 127). 12 Activate and test the services (DLP 128). 13 If necessary, reset the ONT (DLP 126). 14 STOP. This procedure is complete. NTP November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

48 NTP 167 Replace an I-240E-P indoor ONT Purpose This NTP provides the steps to replace I-240E-P indoor ONTs. General The DLPs listed in this NTP describe mounting and cabling for I-240E-P indoor ONTs. Prerequisites See the listed DLPs for prerequisites. Recommended tools You need the following tools for replacing the ONT: #2 Phillips screwdriver 1/4 in. (6 mm) flat blade screwdriver wire strippers fiber optic splicing tools RJ-45 cable plug crimp tool voltmeter or multimeter optical power meter wall mounting template drill and drill bits Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November 2013 NTP FE AAAA TCZZA Edition 01

49 NTP 167 Replace an I-240E-P indoor ONT Safety information Read the following safety information before replacing the unit. Danger 1 Contact the local utility company before you connect the enclosure to the utilities. Danger 2 Observe the local and national laws and regulations that may be applicable to this installation. Danger 3 If the coaxial output of the ONT is connected to the dwelling infrastructure coaxial distribution system, ensure that the coaxial distribution system is separately grounded. Grounding of the dwelling coaxial infrastructure shall use Listed grounding devices and must be installed in accordance with local Codes and Article 800 of the National Electric Code, ANSI/NFPA 70, following the manufacturers instructions. Warning This equipment is ESD sensitive. Proper ESD protections should be used when removing the fiber access cover of the indoor ONT. Caution Keep indoor ONTs out of direct sunlight. Prolonged exposure to direct sunlight can damage the unit. Procedure Note Observe the following: The indoor ONT should be installed in accordance with the applicable requirements of the NEC or CEC. Local authorities and practices take precedent when there is conflict between the local standard and the NEC or CEC. The indoor ONT must be installed by qualified service personnel. Indoor ONTs must be installed with cables that are suitably rated and listed for indoor use. See I-240E-P detailed specifications in the unit data sheet for the temperature ranges for this ONT. Use this procedure to replace an I-240E-P indoor ONT. 1 Deactivate the ONT services (DLP 131). If you are using the SLID feature, this step is not required. The ONT and the services can remain in service (IS). 2 Disconnect the POTS, Ethernet, fiber optic cables (DLP 133), and power cables from the ONT; see Figure NTP for the connector locations on I-240E-P ONT. NTP November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

50 NTP 167 Replace an I-240E-P indoor ONT Figure NTP 167-1: I-240E-P indoor ONT connections POWER OPTICAL LAN UPDATE ALARM POTS GE1 GE2 GE3 GE4 POTS1 POTS2 RESET PWR Ethernet ports (RJ45) POTS ports (RJ-11) Fiber optic connector Power connector Reset button Replace the ONT with a new unit: a b On a flat surface, such as a desk, substitute a replacement ONT for the old ONT; go to step 4. On a wall. i ii Slide the old ONT off of the mounting screws until the ONT is free of the wall. Install the replacement ONT following the wall mounting instructions for an I-240E-P indoor ONT (DLP 122). 4 Connect the Ethernet cables to the RJ-45 ports (DLP 101). 5 Connect the POTS cables to the RJ-11 ports (DLP 123). 6 If required, have approved service personnel who are trained to work with optic fiber clean the fiber optic connection. See DLP 134 for more information about fiber optic handling, inspection, and cleaning. Danger Fiber optic cables transmit invisible laser light. To avoid eye damage or blindness, never look directly into fibers, connectors, or adapters. 7 Connect the SC/APC fiber optic cable (DLP 125). Warning Be careful to maintain a bend radius of no less than 1.5 inches (3.8 cm) when connecting the fiber optic cable. Too small of a bend radius in the cable can result in damage to the optic fiber. 8 Install the power supply according to manufacturer specifications. Note Observe the following: Units must be powered by a Listed or CE approved and marked limited power source power supply with a minimum output rate of 12 V dc, 1.25 A. 9 Connect the power cable to the power connector. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November 2013 NTP FE AAAA TCZZA Edition 01

51 NTP 167 Replace an I-240E-P indoor ONT 10 If used, configure the SLID (chapter 6). Note A new SLID or the old SLID may be used with the replacement ONT. If a new SLID is used, the new SLID must also be programmed at the P-OLT using TL1 or a network manager. If the old SLID is used, no changes need to be made at the P-OLT; see the operations and maintenance documentation for the OLT for more details. 11 Verify the ONT LEDs, voltage status, and optical signal levels (DLP 127). 12 Activate and test the services (DLP 128). 13 If necessary, reset the ONT (DLP 126). 14 STOP. This procedure is complete. NTP November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

52 NTP 168 Configure an I-240E-P indoor ONT General Please refer to the OLT Operations and Maintenance using TL1 and CLI guide for the software configuration procedure for I-240E-P indoor ONTs. For HTTP configuration procedures, please refer to chapter 6, ONT management using an ONT interface. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November 2013 NTP FE AAAA TCZZA Edition 01

53 NTP 168 Configure an I-240E-P indoor ONT NTP November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

54 I-240G-A, I-241G-A 31 I-240G-A and I-241G-A unit data sheet NTP 169 Install an I-240G-A or I-241G-A indoor ONT NTP 170 Replace an I-240G-A or I-241G-A indoor ONT NTP 171 Configure an I-240G-A or I-241G-A indoor ONT Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

55 November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

56 31 I-240G-A and I-241G-A unit data sheet 31.1 I-240G-A and I-241G-A part numbers and identification I-240G-A and I-241G-A general description I-240G-A and I-241G-A software and installation feature support I-240G-A and I-241G-A interfaces and interface capacity I-240G-A and I-241G-A ONT LEDs I-240G-A and I-241G-A detailed specifications I-240G-A and I-241G-A GEM ports and T-CONTs I-240G-A and I-241G-A power support I-240G-A and I-241G-A functional blocks I-240G-A and I-241G-A standards compliance I-240G-A and I-241G-A special considerations Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

57 31 I-240G-A and I-241G-A unit data sheet 31.1 I-240G-A and I-241G-A part numbers and identification Table 31-1 provides identification information about I-240G-A and I-241G-A indoor ONTs. Table 31-1 I-240G-A and I-241G-A part numbers and identification Part number Mnemonic (1) Description CLEI CPR ECI/Bar code 3FE AB I-240G-A 3FE AA I-240G-A GPON I-series ONT, version A, asymmetric, 2 POTS, and 4 Ethernet 10/100/1000Base-T 3FE AC I-240G-A 3FE AA I-240G-A GPON I-series ONT, version A, asymmetric, 2 POTS, and 4 Ethernet 10/100/1000Base-T. The AC variant provides RSSI-capable optics 3FE AD I-240G-A 3FE AA I-240G-A GPON I-series ONT, version A, asymmetric, 2 POTS, and 4 Ethernet 10/100/1000Base-T. The AD variant provides optics that support RSSI as well as different software functions, as outlined in this data sheet. 3FE AA I-240G-A 3FE AA I-240G-A GPON I-series ONT, version A, asymmetric, 2 POTS, and 4 Ethernet 10/100/1000Base-T. Provides a customer-specific logo. 3FE AA I-241G-A I-241G-A GPON I-series ONT, version A, asymmetric, 2 POTS, 4 Ethernet 10/100/1000Base-T, and 1 RF video Note (1) See Chapter 2 Part numbers, ordering, and deployment configuration overview for product identification information I-240G-A and I-241G-A general description The I-240G-A and I-241G-A indoor ONT provides the subscriber interface for the network. The ONT terminates the PON interface and converts it to user interfaces that directly connect to subscriber devices. The ONT is compatible with all existing subscriber equipment, including analog phones with both tone and rotary dial capabilities, cordless phones, modems, fax machines, and caller ID boxes (Type I, Type II, and Type III). These indoor ONT provides the following functions: FSAN GPON standards compliant Network management support IP video with multistage IGMPv3 (RFC 3376) or IGMPv2 (RFC 2236) for channel change network demarcation for all services in an open business model voice interworking function from the analog POTS lines to the VoIP/Ethernet layers 31-2 November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

58 31 I-240G-A and I-241G-A unit data sheet interworking functions between the GEM and Ethernet layers interworking functions between the PON optical overlay and the RF video interface mux and demux functions to the PON optical to electrical conversion G984.4 standard and revised compliant OMCI interface for ONT management and provisioning 31.3 I-240G-A and I-241G-A software and installation feature support Table 31-2 provides a list of software-based features and installation information supported by I-240G-A and I-241G-A indoor ONTs. Table 31-2 I-240G-A and I-241G-A ONT software feature support Features Chapter Cross reference for more information General ONT and MDU overview Service interface specifications ONT and MDU overview ONT and MDU general and interface technical specifications ONT and MDU general descriptions of features and functions Ethernet interface specifications POTS interface specifications RF video interface specifications for video overlay (I-241G-A ONT only) Coaxial connectivity in the home and design guidelines Configuration recommendations 14 dbmv RF video receivers Services supported See the appropriate P-OLT user documentation for service creation procedures and descriptions. RSSI specifications Wi-Fi specifications Optical budget Location and installation options HTTP management Statistics and performance monitoring Supported UPS configurations ONT and MDU general and interface technical specifications How to install and replace an I-240G-A or I-241G-A indoor ONT Information necessary to manage an ONT at a local site using an HTTP interface, CLI interface, CLI interface or butt set. ONT and MDU statistics and performance monitoring Part numbers, ordering, and deployment configuration overview ONT optical budget Install an I-240G-A or I-241G-A indoor ONT Replace an I-240G-A or I-241G-A indoor ONT ONT management using an ONT interface Performance monitoring statistics for Package A ONTs ONT and MDU to UPS or power adapter compatibility support Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

59 31 I-240G-A and I-241G-A unit data sheet 31.4 I-240G-A and I-241G-A interfaces and interface capacity Table 31-3 describes the supported interfaces and interface capacity for I-240G-A and I-241G-A ONTs. Table 31-3 I-240G-A and I-241G-A ONT interface connection capacity ONT type and model Maximum capacity POTS 10/ 100/ BASE-T 10/ 100/ 1000 BASE-T RF video (CATV) MoCA VDSL2 DS1/ E1 Local craft GPON SC/ APC I-240G-A I-241G-A I-240G-A and I-241G-A connections and components I-240G-A and I-241G-A ONTs are for indoor deployment and can be installed vertically or horizontally. Connections to the SC/APC, RJ-45, RJ-11, and coaxial connectors are on the outside of the ONT. Figure 31-1 shows the physical connections for I-240G-A and I-241G-A indoor ONTs. Figure 31-1 I-240G-A and I-241G-A indoor ONT connections PON Video coaxial connector RJ-11 phone connectors Ethernet ports Fiber optic port Power connection Figure 31-1 shows the I-241G-A indoor ONT. The I-240G-A indoor ONT is identical to the I-241G-A ONT except it does not have a video coaxial connector. Table 31-4 describes the I-240G-A and I-241G-A indoor ONT physical connections November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

60 31 I-240G-A and I-241G-A unit data sheet Table 31-4 I-240G-A and I-241G-A indoor ONT connections Connection POTS connections RF video coaxial connector (I-241G-A ONT only) Fiber optic port Ethernet ports Power Description This connection is provided through an RJ-11 phone connector. This connection is provided through a coaxial cable. This connection is provided through a fiber optic cable. This connection is provided through an Ethernet RJ-45 cable. Up to four Ethernet connections are supported.the Ethernet port can support both data and in-band video services on all four interfaces. This connection is provided through a cable to the ac/dc power converter I-240G-A and I-241G-A ONT LEDs Figure 31-2 shows the I-240G-A and I-241G-A indoor ONT LEDs. Figure 31-2 I-240G-A and I-241G-A indoor ONT LEDs PWR FAIL VIDEO DATA1 DATA2 DATA3 DATA4 NTWK MGMT VOICE PWR FAIL Video DATA1 DATA2 DATA3 DATA4 NTWK MGMT VOICE Table 31-5 lists I-240G-A and I-241G-A indoor ONT LEDs Table 31-5 I-240G-A and I-241G-A indoor ONT LEDs Indicator LED color and behavior LED behavior description PWR FAIL RF TV (1) (1 of 2) Off Green solid Off Red solid Off Red solid Not powered 3.3 V dc power is available Equipment is 100% operational Equipment failure or ONT not ranged/synchronized Video signal is not provisioned, or is above the acceptable level Video signal is provisioned and below acceptable level Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

61 31 I-240G-A and I-241G-A unit data sheet Indicator LED color and behavior LED behavior description DATA1 DATA2 DATA3 DATA4 NTWK MGMT Off Green solid Green flashing Off Green solid Green flashing Off Green solid Green flashing Off Green solid Green flashing Off Green solid Off Green solid Green flashing Ethernet 0 link failure Ethernet 0 link is good Ethernet 0 link is in Tx/Rx activity Ethernet 1 link failure Ethernet 1 link is good Ethernet 1 link is in Tx/Rx activity Ethernet 2 link failure Ethernet 2 link is good Ethernet 2 link is in Tx/Rx activity Ethernet 3 link failure Ethernet 3 link is good Ethernet 3 link is in Tx/Rx activity 1490 nm data path is unavailable 1490 nm data path is available No communication between P-OLT and the ONT Full communication between P-OLT and the ONT ONT is disabled When device is not connected to the PON VOICE (2) Off Green flashing periodic Green flashing patterned No SLID activity and all phones on-hook SLID input mode Provisioned SLID in SLID output mode When device is connected to the PON VOICE (2 of 2) Off Green solid All phones are on-hook, POTS is not provisioned, or no phones connected Any customer is off-hook Notes (1) The RF TV LED is only functional for RF video-equipped ONTs. (2) See SLID and LED behaviorfor a description of SLID output mode LEDs. Table 31-6 lists the RJ-45 LEDs on I-240G-A and I-241G-A indoor ONTs. Table 31-6 I-240G-A and I-241G-A indoor ONT RJ-45 LEDs Indicator (1) LINK MODE LED color and behavior Off Green solid Green flashing Off Green solid Green flashing LED behavior description Link not detected Link active Link detected and activity present 10 Mb/s operation 100 Mb/s operation 1000 Mb/s operation Note (1) LINK and MODE LEDs are reversed on the I-240G-A and I-241G-A 31-6 November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

62 31 I-240G-A and I-241G-A unit data sheet 31.6 I-240G-A and I-241G-A detailed specifications Table 31-7 lists the physical specifications for I-240G-A and I-241G-A indoor ONTs. Table 31-7 I-240G-A and I-241G-A indoor ONT physical specifications Dimensions Length Width Height without cable tray Height with cable tray Weight without cable tray [within ± 0.5 lb (0.23 kg)] Weight with cable tray [within ± 0.5 lb (0.23 kg)] Specifications 8.2 in. (20.8 cm) 5.6 in. (14.3 cm) 1.3 in. (3.3 cm) 1.9 in. (4.8 cm) 1.25 lb (0.57 kg) 1.41 lb (0.64 kg) Table 31-8 lists the power consumption specifications for I-240G-A and I-241G-A indoor ONTs. Table 31-8 I-240G-A and I-241G-A indoor ONT power consumption specifications Mnemonic Maximum power (Not to exceed) Condition Minimum power Condition I-240G-A 11 W 2 POTS off-hook, 4 Gig-E operational I-241G-A 13 W 2 POTS off-hook, 4 Gig-E, Video operational 6.5 W 2 POTS on-hook, other interfaces/services not provisioned 6.5 W 2 POTS on-hook, other interfaces/services not provisioned Table 31-9 lists the environmental specifications for I-240G-A and I-241G-A indoor ONTs. Table 31-9 I-240G-A and I-241G-A indoor ONT environmental specifications Mounting method Temperature range and humidity Altitude I-240G-A and I-241G-A indoor 10/100/1000Base-T Gigabit Ethernet ONTs (1 of 2) Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

63 31 I-240G-A and I-241G-A unit data sheet Mounting method Temperature range and humidity Altitude Desk or wall mounted (2 of 2) Operating: 32 F to 104 F (0 C to 40 C) ambient temperature 5% to 85% relative humidity, non-condensing Maximum rate of temperature change is 32.9 F (18.3 C) per hour Storage: -13 F to 133 F (-25 C to 55 C) 5% to 93% relative humidity, non-condensing Maximum operating altitude is ft (3048 m) above mean sea level Maximum non-operating altitude is ft ( m) above mean sea level Table lists RF video interface specifications for I-241G-A indoor ONTs. Table I-241G-A ONT RF video interface specifications RF video features Channel mix 80 analog/33 digital (1) Channel mix 40 analog/63 digital Channel mix 0 analog/135 digital RF output level MHz using a per analog channel measurement MHz using a per analog channel measurement MHz using a per digital channel measurement RF slope correction (tilt) 2 db from 50 to 870 MHz 2 db from 50 to 870 MHz 2 db from 88 to 870 MHz Optical power range +1 to -6 db +2 to -7 db +1 to -9 db CNR 45 db 46 db CSO/CTB 53 db 55 db MER 32 db 32 db 32 db QAM signal-to-noise ratio 40 db 40 db 40 db Measurement assumptions Channel load 80 analog and 33 digital 40 analog and 63 digital 0 analog and 135 digital Digital backoff QAM db 6 db 6 db Digital backoff QAM db 10 db 10 db PON input CNR 52 db 52 db 52 db Note (1) It is the responsibility of the customer installation crew to ensure proper on-site layout of video distribution by verifying that the output power at the end devices, such as the TV, VCR, and STB, is between 0 to 18 dbmv I-240G-A and I-241G-A GEM ports and T-CONTs Table lists the maximum number of supported T-CONTs and GEM ports. Not all ONTs will be supported in all of the releases indicated the table. See the appropriate release Customer Release Notes for the most accurate list of supported devices November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

64 31 I-240G-A and I-241G-A unit data sheet Table I-240G-A and I-241G-A indoor ONTs capacity for GEM ports and T-CONTs per package and release ONT or MDU Release Maximum Notes Package A ONTs GEM ports per indoor or outdoor ONT T-CONTs per indoor or outdoor ONT All are present: 20 are available, 2 are reserved for OMCI and debugging All are present: 21 are available, 1 is reserved for OMCI 31.8 I-240G-A and I-241G-A power support The following power supply supports the I-240G-A and I-241G-A indoor ONT. Click on the link for more information. CyberPower CyberShield CS 24 UPS unit data sheet Emerson 24 W AC/DC switching power adapter unit data sheet 31.9 I-240G-A and I-241G-A functional blocks Table describes the supported interfaces for I-240G-A and I-241G-A indoor ONTs. Table I-240G-A and I-241G-A indoor ONT interfaces ONT category description Interface capacity POTS ports Ethernet ports RF video connectors POTS/ VDSL2 / 10/100/ 1000 BASE-T Ethernet connectors DS1/E1 Single-residence indoor ONTs (I-240G-A and I-241G-A) 2 4 0/1 0 0 ONT SoC technology is an integrated system that provides the GPON, voice, and data (including IP video) subsystems. It provides two key connection functions: connecting the ONT to the GPON and the connecting the ONT to subscriber equipment. The voice subsystem supports RJ-11 ports, and the data and IP video subsystems support RJ-45 ports. The ONT connects to the GPON using a optical connector. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

65 31 I-240G-A and I-241G-A unit data sheet The GPON connection performs a GPON transmission convergence (TC) layer function. The GPON signal from the P-OLT terminates at a diplexer. The diplexer is an optical module that performs optical and electrical conversion. The diplexer interfaces with the GPON MAC on the SoC. Figure 31-3 shows an ONT with a diplexer, four POTS, and two Ethernet ports. Figure 31-3 ONT with a diplexer Power Converter GPON Diplexer SOC POTS (4) Ethernet (2) RJ-11 RJ Package A ONT SoC technology serves as the main hardware block for these indoor ONTs. ONT SoC technology consists of five key elements: GPON MAC The GPON MAC element on the SoC provides the GPON interface to the TC layer via the optical diplexer or triplexer (if using RF video). This interface supports the FSAN standards compliant GEM mode transport and provides AES, FEC, and data fragmentation functionality over the GPON as described in G (GPON TC Layer) ITU specification. Ethernet MAC The SoC provides an Ethernet PHY device (either 10/100BaseT or 10/100/1000BaseT) between the GMII interface and the RJ-45 port. Digital Signal Processor (DSP) interface The DSP provides voice processing and has a TDM interface to the CODEC/SLIC devices. control processor The control processor manages functions related to OMCI, IGMP, VoIP, and Ethernet services. SoC bridge The SoC bridge provides an integrated data channel between the Ethernet MAC, the GPON MAC, the DSP, the control processor, and the other integrated elements such as flash memory, SDRAM, the local bus controller, and the DUART interface to the craft port if used. These ONTs can also interact with additional hardware components to support functionality not provided by SoC technology. For example, MoCA and CES functionality require additional hardware support November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

66 31 I-240G-A and I-241G-A unit data sheet I-240G-A and I-241G-A standards compliance The I-240G-A and I-241G-A indoor ONT is compliant with the following standards: G (revised) support for OMCI interface for ONT management and provisioning G support for Dynamic Bandwidth Allocation (DBA) G support for Advanced Encryption System (AES) with operator enable/disable per port-id level G support for Forward Error Correction (FEC) in both upstream and downstream directions G984.4 (standard and revised) support for OMCI interface for ONT management and provisioning I-240G-A and I-241G-A special considerations I-240G-A and I-241G-A ONT software considerations and limitations Table lists the software considerations and limitations for I-240G-A and I-241G-A indoor ONTs. Table I-240G-A and I-241G-A indoor ONT software considerations and limitations Considerations and limitations No support for per VLAN protocol downstream tagging mode In SVLAN cross-connect tunnel mode: use non-overlapping pbits since the use of the same pbits on two or more VLAN ports results in a mismatch alarm downstream frames sent with a single tag normally sent out on the user-side as untagged, will instead be sent as priority tagged When using CVLAN translation, or when the same queue is used for multiple pbits, the highest pbit value in the queue in the downstream direction will be selected to stomp the pbit in the packet Simultaneous configuration of a CVLAN port and an S-Tunnel on the same UNI will only be supported if these services are provisioned with non-overlapping pbits The same VLAN port must be used when employing both protocol-based VLAN for PPPoE and IPoE-based VLANs When the VLAN is translated, the pbit value must be modified and the highest pbit value is mapped to that GEM port When more than one Ethernet port is in VLAN translation mode, or set to flexible mode with IGMP channels created, the USERSIDE VLAN IDs of those services are different. All downstream multicast packets will be tagged on the UNI port with VLAN ID of 4094 Maximum use of multicast on 1 Ethernet port at a time For C forwarder and S+C CC forwarder, if the VLAN port uses regenerated profiles or regenerated pbits, then the downstream traffic can only flow with the derived pbits When either tip or ring is grounded, DGNONTPOTS tip to ground and ring to ground restrictive measurements are simultaneously reported as 0 ohms The ONT cannot forward CCM packets to the edge router (1 of 2) Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

67 31 I-240G-A and I-241G-A unit data sheet Considerations and limitations The ONT does not support RIPv2 or SAPv1 packets on an unicast VLAN that is not the multicast GEM port The ONT cannot perform subscriber join IGMP CAC check when LT-to-ONT signalling is disabled (2 of 2) Upgrade considerations and limitations Existing ONTs that use 7342 ISAM FTTU releases older than R04.06.xx and R04.07.xx must be upgraded to use R software while assigned to a PON ID value smaller than 64. For this purpose, if split ratios larger than 1:64 are being deployed, you may choose to set aside the first PON ID as a staging point. In order to provide four GE ports on the I-241G-A indoor ONT, an Ethernet switch has been added between the SoC and the Ethernet ports; See Figure The Ethernet switch provides the following features: IGMP packet replication for multicast channels internal VLAN tagging to direct traffic to appropriate ports and priority queues Figure 31-4 Ethernet switch Power Converter GPON Triplexer SOC POTS Ethernet switch RJ-11 RJ-45 Video amplifier F Note The RF video amplifier is integrated with the triplexer. It is shown split-out in Figure 31-4 to illustrate the functionality. IGMP packet replication allows the I-241G-A to support IPTV on all four Ethernet channels at the same time. Internal VLAN tagging allows traffic to be routed and prioritized between the two Ethernet MACs on the SoC and the Ethernet switch and the appropriate subscriber RJ-45 ports. Downstream multicast traffic received on a user side C-VLAN tagged port will use VLAN ID 4094 and have a P-bit value of 6. The I-241G-A ONTs do not support downstream priority-tagged traffic on their ONT UNIs. Priority-tagged frames are dropped. When an unstacked VLAN is provisioned on the ONT UNI, downstream traffic that is single tagged is dropped November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

68 31 I-240G-A and I-241G-A unit data sheet The new Ethernet switch functional block and the additional Ethernet switch features have modified certain VLAN tagging and priority queuing behaviors. The following sections describe these modifications. Note 1 Due to certain Ethernet switch restrictions, the I-241G-A provides up to 4 IP, 4 MAC, or 2 pairs of MAC/IP based anti-spoofing (static only). MAC, IP, and MAC/IP anti-spoofing only works on both IPoE packets. Note 2 Congestion may occur if Ethernet ports 1 and 2 or ports 3 and 4 are each set to 1000Base-T and are being used simultaneously. See the ONT Customer Release Notes for this product for throughput details. I-240G-A and I-241G-A ONT hardware limitations Table lists the hardware limitations for the I-240G-A and I-241G-A indoor ONT when configuring services. Table I-240G-A and I-241G-A indoor ONT hardware limitations Limitation Parameters (1) Service(s) The I-241G-A ONT does not support downstream priority-tagged frames on its UNIs. Priority-tagged frames are dropped. When configuring an unstacked PON VLAN, ensure that the PON VLAN is configured in pass-through mode so that the LT does not set the S-VLAN ID to 0, or the corresponding ONT UNI is configured in VLAN translation mode or VLAN translation mode with EtherType classification. In the latter case, the ONT translates the S-VLAN ID to the UNI-side C-VLAN ID of the service or flow. In the VLAN translation mode and the VLAN translation mode with EtherType classification, I-241G-A ONTs cannot have a UNI C-VLAN ID of zero. When an upstream priority-tagged frame is received on one of these ONTs, the C-VLAN ID of zero is overwritten with the port-based default C-VLAN ID. I-241G-A ONT must be enabled for port-to-port communication to support the flexible mode. In this communication mode, a business service can only be configured on port 1, and the service is replicated on the other enabled ONT UNI ports. The following are not supported: both VLAN translation and VLAN pass-through on traffic using the same p-bit across the same UNI VLAN translation when networksidevlan is 4096 and unisidevlan is 0 to Upstream traffic is classified and forwarded as pass-through traffic. Downstream traffic is not translated to the unisidevlan setting. (1 of 2) tagmode proftype unisidevlan proftype ONT UNI ports include cvlandef (Ethernet port) cvlandef (VDSL2 port) proftype p2penable unisidevlan networksidevlan PON VLAN QoS HSI and Flow QoS QoS ONT HSI Flow Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

69 31 I-240G-A and I-241G-A unit data sheet Limitation Parameters (1) Service(s) Downstream p-bit translation is not supported when the flow is configured for VLAN pass-through. In this case, the following applies: a flow with networksidevlan 4096 and unisidevlan 4096, will pass downstream p-bits to the UNI unchanged a flow with networksidevlan and unisidevlan set to the same value (0 to 4094), will pass downstream p-bits to the UNI changed to the highest p-bit value specified by the PQ profile When all of the following apply, the highest UNI-side p-bit value defined in the p-bit translation profile is used: unisidevlan is 0 to 4094 and networksidevlan is 0 to 4094, or unisidevlan is 4096 and networksidevlan is 4096 pbitxlprofid/nm is not 0 p-bit translation is not defined for the downstream p-bit in the p-bit translation profile (2 of 2) unisidevlan networksidevlan pbitxlprofid pbitxlpofnm HSI Flow Note (1) See Operations and Maintenance documentation for the I-240G-A or I-241G-A for information on these parameters. VLAN tagging behavior Before traffic can be routed to and from the I-241G-A ONT the following conditions must be met: The CVLAN ID of any HSI service cannot be 0. Default P-bits must be configured on each Ethernet port. This can be configured using the ENT-QOS-MARKPROF command. See the appropriate P-OLT Operations and Maintenance Procedure Guide for more information. When port-to-port communication is disabled, a default C-VLAN must be created for each Ethernet port. The VLAN must be unique for Ethernet port 1 and 2 or 3 and 4 on the ONT. The C-VLAN packet received at the ONT must be the same as the default C-VLAN or the packet is dropped. When port-to-port communication is enabled, each of the four Ethernet ports must have an unique C-VLAN. The default VLAN can be configured using the CVLANDEF parameter. DSCP to 1P mapping rules are reduced from 64 to 8 with only the highest 3 bits of the DSCP area used to determine P-bit value; see Table This can be configured using the ENT-PROFILE-DSCPBITMAP command. See the appropriate P-OLT Operations and Maintenance Procedure Guide for more information. Table Default DSCP to P-bit mapping DSCP P-bit (1) 0 to 7 x (1 of 2) November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

70 31 I-240G-A and I-241G-A unit data sheet Note (1) Where x is a number from 0 to 7. DSCP P-bit (1) 8 to 15 x 16 to 23 x 24 to 32 x 33 to 40 x 41 to 47 x 48 to 55 x 56 to 63 x (2 of 2) All VLAN tagging behavior operates as described in the appropriate P-OLT system documentation except as indicated in the following sections. Upstream traffic handling (trusted and untrusted) Table describes upstream VLAN tagging and P-bit allocation from trusted and untrusted traffic. Table Upstream untrusted and trusted tagging behavior Traffic source Traffic type Ethernet switch behavior Untrusted Untagged packets Default C-VLAN and P-bits are added to the packets. P-bit tagged packets P-bit and C-VLAN tagged packets Default C-VLAN is added to the packets. P-bits are overwritten. Received C-VLAN and P-bits are overwritten. Trusted Untagged packets Default C-VLAN and P-bits are added to the packets.if the packets are IP, the DSCP to P-bits mapping is used. If the packets are PPPoE, the default P-bits are used. P-bit tagged packets P-bit and C-VLAN tagged packets Received P-bits are overwritten with default C-VLAN. P-bits are unchanged. Received C-VLAN must match default VLAN or the packet is dropped. P-bits are unchanged. Downstream traffic handling (strip tag and tag through) Table describes downstream VLAN tagging behavior for strip tag and tag through modes. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

71 31 I-240G-A and I-241G-A unit data sheet Table Downstream untrusted and trusted tagging behavior Traffic mode Traffic type Transmitted to ONT port as Strip tag Untagged packets Untagged packet. P-bit tagged packets C-VLAN tagged packets Untagged packet. Untagged packet. Tag through Untagged packets Untagged packet. P-bit tagged packets C-VLAN tagged packets Default C-VLAN is added and the maximum number of P-bits will be accepted. Default C-VLAN overwrites the received C-VLAN and the maximum number of P-bits will be accepted. VLAN translation traffic handling VLAN translation is a feature that allows that ONT to translate a C-VLAN into another C-VLAN. A network (NW) C-VLAN is used when data is sent over the GPON network, and a user network interface (UNI) side C-VLAN is used when data is sent to customer equipment. When using VLAN translation, the use the following configuration rules: Only a single UNI/NW C-VLAN pair is allowed per service. Overlapping P-bits can be used for difference services on UNI. However, in VLAN pass-tru mode, the same P-bits as other services cannot be used on the UNI. Overlapping P-bits are allowed only for non-default services. Table describes upstream VLAN tagging and P-bit allocation in VLAN translation mode. Table Upstream VLAN translation mode Traffic mode Traffic type Ethernet switch behavior VLAN translation Untagged packets Default C-VLAN and P-bits are added to the packets.if the packets are IP, the DSCP to P-bits mapping is used. If the packets are PPPoE, the default P-bits are used. The C-VLAN and derived P-bits are now considered the UNI side C-VLAN. Received UNI C-VLAN and P-bits must match NW C-VLAN configure P-bits or the packet is dropped. P-bit and C-VLAN tagged packets Received UNI C-VLAN and P-bits must match NW C-VLAN configure P-bits or the packet is dropped. Table describes downstream VLAN tagging behavior for VLAN translation November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

72 31 I-240G-A and I-241G-A unit data sheet Table Downstream VLAN translation behavior Traffic mode Traffic type GPON behavior Ethernet switch behavior VLAN translation Tagged packets Only accepts VLAN tagged traffic that matches the network VLAN ID configured using the ENT-SERVICE-HSI TL1 command. All non matching VLAN IDs are dropped. Only one service is allowed per VLAN. The Ethernet switch converts the network VLAN ID to the user side VLAN ID and forwards the packet to the appropriate port. Ethertype classification and Ethertype with VLAN translation Ethertype classification is used to classify traffic in the upstream direction based on the Ethernet type (IPoE or PPPoE). Ethertype classification operates as normal except that the received C-VLAN must match the default C-VLAN configured at the ONT or the packet is dropped. Ethertype classification may also be used in conjunction with VLAN translation. All the considerations described in the VLAN translation section apply with the additional that the received C-VLAN and Ethertype must match the default NW C-VLAN an Ethertype or the packet is dropped. See the appropriate P-OLT system Product Information Manual for more information on Ethertype classification. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

73 31 I-240G-A and I-241G-A unit data sheet November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

74 NTP 169 Install an I-240G-A or I-241G-A indoor ONT Purpose This NTP provides the steps to install an I-240G-A or I-241G-A indoor ONT. General The DLPs listed in this NTP describe the steps to install an I-240G-A or I-241G-A indoor ONT. Prerequisites See the listed DLPs for prerequisites. Recommended tools You need the following tools for the installation: #2 Phillips screwdriver 1/4 in. (6 mm) flat blade screwdriver wire strippers fiber optic splicing tools RJ-45 cable plug crimp tool voltmeter or multimeter optical power meter wall mounting template drill and drill bits Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November 2013 NTP FE AAAA TCZZA Edition 01

75 NTP 169 Install an I-240G-A or I-241G-A indoor ONT Safety information Read the following safety information before installing the unit. Danger 1 Always contact the local utility company before you connect the enclosure to the utilities. Danger 2 Observe the local and national laws and regulations that may be applicable to this installation. Warning This equipment is ESD sensitive. Proper ESD protections should be used when removing the fiber access cover of the indoor ONT. Caution Keep indoor ONTs out of direct sunlight. Prolonged exposure to direct sunlight can damage the unit. Procedure Note Observe the following: The indoor ONT should be installed in accordance with the applicable requirements of the NEC or CEC. Local authorities and practices take precedence when there is conflict between the local standard and the NEC or CEC. The indoor ONT must be installed by qualified service personnel only. Indoor ONTs must be installed with cables that are suitably rated and listed for indoor use. See I-240G-A and I-241G-A detailed specifications in the unit data sheet for the temperature ranges for ONTs. Use this procedure to install an I-240G-A or I-241G-A indoor ONT. 1 Prepare the cables at the site where the ONT will be installed (DLP 100). 2 Review the connection locations shown in Figure NTP NTP November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

76 NTP 169 Install an I-240G-A or I-241G-A indoor ONT Figure NTP 169-1: I-241G-A indoor ONT connections PON Video coaxial connector RJ-11 phone connectors Ethernet ports Fiber optic port Power connection Figure NTP shows the I-241G-A indoor ONT. The I-240G-A indoor ONT is identical to the I-241G-A ONT except it does not have a video coaxial connector. 3 Place the indoor ONT unit: a b On the flat surface, such as a desk, horizontally resting on its four plastic feet; go to step 4. In the stand mount (3FE AA). i ii Place the stand mount on the flat surface. Slide the ONT into the opening on the stand mount, ensuring it is securely held. Figure NTP shows the stand mount. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November 2013 NTP FE AAAA TCZZA Edition 01

77 NTP 169 Install an I-240G-A or I-241G-A indoor ONT Figure NTP 169-2: ONT in a stand mount EQPT PON MGMT Data 2 Data iii Go to step 4. c In the wall mount bracket. i ii iii iv Measure and drill two holes in the wall where the ONT will be mounted. The holes should be the same distance apart as the holes on the wall mounting bracket (83.3 mm apart, or 3.28 in). Place mounting screws or bolts in the wall. Lay the mounting bracket flat on a table. Slide the ONT down over the mounting bracket until the fiber optic port is directly in front of the fiber optic port cable lead, as shown in Figure NTP NTP November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

78 NTP 169 Install an I-240G-A or I-241G-A indoor ONT Figure NTP 169-3: I-240G-A or I-241G-A indoor ONT with wall mounting bracket PON PON v Mount the ONT on the pre-installed screws or bolts in the bracket mounting holes. Ensure the ONT is firmly held in place by the bracket and is firmly secured to the wall. 4 Install the AC power converter and connect the power cable to the ONT (DLP 106). 5 Connect the Ethernet cable to an RJ-45 connector (DLP 101). 6 Connect the POTS cables to the RJ-11 connectors (DLP 123). 7 For the I-241G-A indoor ONT only, connect the coaxial cable (DLP 116). 8 If used, configure the SLID (DLP 129). 9 Connect the fiber optic cable (DLP 125). 10 Verify the ONT LEDs (DLP 127). 11 Activate and test the services (DLP 128). 12 STOP. This procedure is complete. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November 2013 NTP FE AAAA TCZZA Edition 01

79 NTP 169 Install an I-240G-A or I-241G-A indoor ONT NTP November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

80 NTP 170 Replace an I-240G-A or I-241G-A indoor ONT Purpose This NTP provides the steps to replace an I-240G-A or I-241G-A indoor ONT. General The DLPs listed in this NTP describe mounting and cabling for the I-240G-A or I-241G-A indoor ONT. Prerequisites See the listed DLPs for prerequisites. Recommended tools You need the following tools for replacing the ONT: #2 Phillips screwdriver 1/4 in. (6 mm) flat blade screwdriver wire strippers fiber optic splicing tools RJ-45 cable plug crimp tool voltmeter or multimeter optical power meter wall mounting template drill and drill bits Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November 2013 NTP FE AAAA TCZZA Edition 01

81 NTP 170 Replace an I-240G-A or I-241G-A indoor ONT Safety information Read the following safety information before installing the unit. Danger 1 Always contact the local utility company before you connect the enclosure to the utilities. Danger 2 Observe the local and national laws and regulations that may be applicable to this installation. Warning This equipment is ESD sensitive. Proper ESD protections should be used when removing the fiber access cover of the indoor ONT. Caution Keep indoor ONTs out of direct sunlight. Prolonged exposure to direct sunlight can damage the unit. Procedure Note Observe the following: The indoor ONT should be installed in accordance with the applicable requirements of the NEC or CEC. Local authorities and practices take precedent when there is conflict between the local standard and the NEC or CEC. The indoor ONT must be installed by qualified service personnel. Indoor ONTs must be installed with cables that are suitably rated and listed for indoor use. See I-240G-A and I-241G-A detailed specifications in the unit data sheet for the temperature ranges for ONTs. Use this procedure to replace an I-240G-A or I-241G-A indoor ONT. 1 Deactivate the ONT services (DLP 131). If you are using the SLID feature, this step is not required. The ONT and the services can remain in service (IS). 2 At the subscriber site, locate the indoor ONT and disconnect the power, RF video, phone, Ethernet and fiber optic cables; see Figure NTP NTP November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

82 NTP 170 Replace an I-240G-A or I-241G-A indoor ONT Figure NTP 170-1: I-241G-A indoor ONT connections PON Video coaxial connector RJ-11 phone connectors Ethernet ports Fiber optic port Power connection Figure NTP shows the I-241G-A indoor ONT. The I-240G-A indoor ONT is identical to the I-241G-A ONT except it does not have a video coaxial connector. 3 Replace the indoor ONT with a new unit. 4 Connect the Ethernet cable to an RJ-45 connector (DLP 101). 5 Connect the POTS cables to the RJ-11 connectors (DLP 123). 6 For the I-241G-A indoor ONT only, connect the coaxial cable (DLP 116). 7 Connect the power cable to the ac outlet (DLP 106). 8 If used, configure the SLID (DLP 129). Note A new SLID or the old SLID may be used with the replacement ONT. If a new SLID is used, the new SLID must also be programmed at the P-OLT using TL1 or a network manager. If the old SLID is used, no changes need to be made at the P-OLT; see the appropriate P-OLT Operations and Maintenance Procedures Guide for more details. 9 If required, have approved service personnel who are trained to work with optic fiber clean the fiber optic connection. See DLP 134 for more information about fiber optic handling, inspection, and cleaning. Danger Fiber optic cables transmit invisible laser light. To avoid eye damage or blindness, never look directly into fibers, connectors, or adapters. 10 Connect the fiber optic cable to the fiber optic port (DLP 125). Warning Be careful to maintain a bend radius of no less than 1.5 inches (3.8 cm) when connecting the fiber optic cable. Too small of a bend radius in the cable can result in damage to the optic fiber. 11 Verify the ONT LEDs, voltage status, and optical signal levels (DLP 127). Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November 2013 NTP FE AAAA TCZZA Edition 01

83 NTP 170 Replace an I-240G-A or I-241G-A indoor ONT 12 Activate and test the services (DLP 128). 13 STOP. This procedure is complete. NTP November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

84 NTP 171 Configure an I-240G-A or I-241G-A indoor ONT General Please refer to the OLT Operations and Maintenance using TL1 and CLI guide for the software configuration procedure for I-240G-A and I-241G-A indoor ONTs. For HTTP configuration procedures, please refer to chapter 6, ONT management using an ONT interface. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November 2013 NTP FE AAAA TCZZA Edition 01

85 NTP 171 Configure an I-240G-A or I-241G-A indoor ONT NTP November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

86 I-240G-B, I-241G-B, I-240G-C 32 I-240G-B, I-241G-B, and I-240G-C unit data sheet NTP 172 Install an I-240G-B, I-241G-B, or I-240G-C indoor ONT NTP 173 Replace an I-240G-B, I-241G-B, or I-240G-C indoor ONT NTP 174 Configure an I-240G-B, I-241G-B, or I-240G-C indoor ONT Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

87 November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

88 32 I-240G-B, I-241G-B, and I-240G-C unit data sheet 32.1 I-240G-B, I-241G-B, and I-240G-C part numbers and identification I-240G-B, I-241G-B, and I-240G-C general description I-240G-B, I-241G-B, and I-240G-C software and installation feature support I-240G-B, I-241G-B, and I-240G-C interfaces and interface capacity I-240G-B, I-241G-B, and I-240G-C LEDs I-240G-B, I-241G-B, and I-240G-C detailed specifications I-240G-B, I-241G-B and I-240G-C GEM ports and T-CONTs I-240G-B, I-241G-B, and I-240G-C power support I-240G-B, I-241G-B, and I-240G-C functional blocks I-240G-B, I-241G-B, and I-240G-C standards compliance I-240G-B, I-241G-B, and I-240G-C special considerations Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

89 32 I-240G-B, I-241G-B, and I-240G-C unit data sheet 32.1 I-240G-B, I-241G-B, and I-240G-C part numbers and identification Table 32-1 provides identification information about I-240G-B, I-241G-B, and I-240G-C indoor ONTs. Table 32-1 I-240G-B, I-241G-B, and I-240G-C part numbers and identification Part number Mnemonic (1) Description CLEI CPR ECI/Bar code 3FE AB I-240G-B GPON I-series ONT unit, version B, 2 POTS and 4 Ethernet interfaces. 3FE AF (customer-specific variant) 3FE AD (customer-specific variant) 3FE AA I-241G-B GPON I-series ONT unit, version B, 2 POTS, 4 Ethernet, and 1 RF video interfaces. 3FE AK I-240G-C GPON I-series ONT unit, version C, 2 POTS, and 4 Ethernet. A temperature-hardened ONT approved for use with an outdoor enclosure. 3FE AC 3FE AD (customer-specific variant) Outdoor enclosure for the I-240G-C indoor ONT. The ONT enclosure has a fusion splice holder and tamper-proof pin-in-hex security screw. Outdoor enclosure for the I-240G-C indoor ONT. The ONT enclosure has a fusion splice holder and tamper-proof pin-in-hex security screw. This kit includes a Molex power adapter cable (3MV AA) and a POTS screw terminal block. Note (1) See Chapter 2 Part numbers, ordering, and deployment configuration overview for ordering information I-240G-B, I-241G-B, and I-240G-C general description I-240G-B, I-241G-B, and I-240G-C indoor ONTs provide a subscriber interface for the system. The ONT terminates the PON interface and converts it to user interfaces that directly connect to subscriber devices. The ONT is compatible with all existing subscriber equipment, including analog phones with both tone and rotary dial capabilities, cordless phones, modems, fax machines, and caller ID boxes (Type I, Type II, and Type III) November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

90 32 I-240G-B, I-241G-B, and I-240G-C unit data sheet The I-240G-B and I-241G-B indoor ONTs are not temperature hardened. These ONTs are intended for indoor deployment only and can be installed vertically or horizontally on a flat surface as well as attached to a wall. The I-240G-C is temperature hardened and may be installed in an outdoor enclosure. These ONTs provide the following functions: network demarcation for all services voice interworking function from the analog POTS lines to the VoIP/Ethernet layers interworking functions between the GEM and Ethernet layers interworking functions between the PON optical overlay and the RF video interface (I-241G-B ONT only) mux and demux functions to the PON optical to electrical conversion optics that support received signal strength indication (RSSI) G984.4 standard and revised compliant OMCI interface for ONT management and provisioning Other features of I-240G-B, I-241G-B, and I-240G-C indoor ONTs include: a removable fiber access tray for storing excess cable an ON/OFF power switch for manual shut down when needed a reset button located on the base of the ONT Note The maximum supported capacity for downstream data traffic for the I-240G-B indoor ONT is 1 Gb/s. This supported capacity is constant whether one or more Ethernet ports are used. If you use one Ethernet port, the entire 1 Gb/s throughput travels on that port, while, if you use two or more Ethernet ports, the 1 Gb/s capacity is divided among the ports I-240G-B, I-241G-B, and I-240G-C software and installation feature support Table 32-2 provides a list of software-based features for I-240G-B, I-241G-B, and I-240G-C indoor ONTs. Table 32-2 I-240G-B, I-241G-B, and I-240G-C indoor ONT software feature support Features Chapter Cross reference for more information General ONT and MDU overview (1 of 2) ONT and MDU overview ONT and MDU general descriptions of features and functions Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

91 32 I-240G-B, I-241G-B, and I-240G-C unit data sheet Features Chapter Cross reference for more information Service interface specifications ONT and MDU general and interface technical specifications Ethernet interface specifications POTS interface specifications Coaxial connectivity in the home and design guidelines Configuration recommendations Services supported See the appropriate P-OLT user documentation for service creation procedures and descriptions. RSSI specifications ONT and MDU general and interface technical specifications RSSI specifications Wi-Fi specifications Optical budget Location and installation options ONT and MDU general and interface technical specifications How to install, replace, and configure an I-240G-B or I-241G-B ONT ONT optical budget Install an I-240G-B, I-241G-B, or I-240G-C indoor ONT Replace an I-240G-B, I-241G-B, or I-240G-C indoor ONT HTTP management ONT management using an ONT interface Statistics and performance monitoring Supported UPS configurations (2 of 2) ONT and MDU statistics and performance monitoring Part numbers, ordering, and deployment configuration overview Supported performance monitoring counters per package type of ONT ONT and MDU to UPS or power adapter compatibility support 32.4 I-240G-B, I-241G-B, and I-240G-C interfaces and interface capacity Table 32-3 describes the supported interfaces for I-240G-B, I-241G-B, and I-240G-C indoor ONTs. The I-240G-C ONT supports a separately orderable OptiTap connector. Table 32-3 I-240G-B, I-241G-B, I-240G-C indoor ONT interfaces ONT category description Interface capacity POTS ports Ethernet ports VDSL2 interfaces MoCA interface RF Video interface Single-residence Gigabit Ethernet ONTs with or without POTS and RF video (I-240G-B, I-240G-C, and I-241G-B indoor ONTs) /1 I-240G-B, I-241G-B, and I-240G-C connections and components Figures 32-1 shows the I-240G-B and I-240G-C indoor ONT physical connections. Figure 32-2 shows the I-241G-B indoor ONT physical connections November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

92 32 I-240G-B, I-241G-B, and I-240G-C unit data sheet Figure 32-1 I-240G-B and I-240G-C indoor ONT connections Power connector U SB 1 2 POTS1 POTS2 LAN1 LAN2 LAN3 LAN4 POWER Fiber optic connector Phone connectors (RJ-11) Ethernet ports (RJ-45) On/off Figure 32-2 I-241G-B indoor ONT connections Power connector TV U SB 1 2 POTS1 POTS2 LAN1 LAN2 LAN3 LAN4 POWER SC/APC connector RF video coaxial connector POTS connectors (RJ-11) Ethernet connectors (RJ-45) On/off button Table 32-4 describes the I-240G-B, I-241G-B, and I-240G-C indoor ONT physical connections. Table 32-4 I-240G-B, I-241G-B, and I-240G-C indoor ONT physical connections Connection POTS Ethernet ports Power Fiber optic Description This connection is provided through RJ-11 ports. This connection is provided through Ethernet RJ-45 cables. Four Ethernet connections are supported.the Ethernet ports can support both data and in-band video services on all four interfaces. This connection is provided through a power cable with a Molex connector to the power connector. This connection is provided through a SC/APC fiber optic cable and connector. I-241G-B indoor ONT only RF video coaxial This connection is provided through a Type F coaxial connector I-240G-B, I-241G-B, and I-240G-C LEDs Figure 32-3 shows the I-240G-B and I-241G-B indoor ONT LEDs. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

93 32 I-240G-B, I-241G-B, and I-240G-C unit data sheet Figure 32-3 I-240G-B and I-241G-B indoor ONT LEDs VIDEO VOICE VOICE LAN 4 LAN 2 LAN 3 LAN ALARM POWER WAN Figure 32-4 shows the indoor ONT LEDs (I-240G-C) November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

94 32 I-240G-B, I-241G-B, and I-240G-C unit data sheet Figure 32-4 Indoor ONT LEDs (I-240G-C) POWER WAN ALARM SC/APC connector Power connector On/Off button LAN 1 LAN 2 Ethernet connectors (RJ-45) LAN 3 LAN 4 POTS connectors (RJ-11) VOICE VIDEO POTS screw terminals (3FE AD only) Table 32-5 lists and describes the I-240G-B, I-240G-C, and I-241G-B indoor ONT LEDs. Table 32-5 I-240G-B, I-241G-B, and I-240G-C indoor ONT LEDs descriptions Indicator (1) POWER (1 of 2) LED color and behavior Off Green Green flashing Red LED behavior description No power Operating on ac power ONT is starting up Operating on battery backup power Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

95 32 I-240G-B, I-241G-B, and I-240G-C unit data sheet Indicator (1) WAN ALARM LAN 1 to 4 VOICE LED color and behavior Green Green flashing Red Orange Orange flashing Off Red Red flashing Off Green Green flashing Orange/Red flashing Orange Off Green solid LED behavior description PON is connected and operating properly Software downloading PON not connected but ONT has power ONT ranged but OMCI not established ONT is ranging ONT is operating without failure ONT operation failure (not ranged) ONT software failure Not provisioned or no Ethernet connection 10/100 link detected 10/100 link has data activity 1000 link has data activity 1000 link detected No POTS provisioned (all phones are on-hook or no phones connected) One or more phones is off-hook I-241G-B indoor ONT only VIDEO (2 of 2) Off Red Normal operation Service provisioned and optical power too low Note (1) For an I-240G-C ONT installed in an outdoor enclosure, a label supplied with the enclosure must be attached to the surface of the ONT to label the LEDs as documented in the table above. Apply the label on the top surface of the ONT near to the LEDs so that the Power label aligns with the first LED. The text on the label should appear right-side up for reading when the ONT is installed in the enclosure and the unit is wall-mounted (see Figure 32-4). Table 32-6 lists and describes the I-240G-B and I-241G-B indoor ONT RJ-45 LEDs. Table 32-6 I-240G-B and I-241G-B Indoor ONT RJ-45 LEDs Indicator LED color and behavior LED behavior description LINK MODE Off Green solid Green flashing Off Green solid Link not detected Link active Link detected and activity present 10 and 100 Mb/s operation 1000 Mb/s operation 32.6 I-240G-B, I-241G-B, and I-240G-C detailed specifications Table 32-7 lists the physical specifications for I-240G-B, I-241G-B, and I-240G-C indoor ONTs November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

96 32 I-240G-B, I-241G-B, and I-240G-C unit data sheet Table 32-7 I-240G-B, I-241G-B, and I-240G-C indoor ONT physical specifications Dimensions Length Width Height without cable tray Height with cable tray Weight without cable tray [within ± 0.5 lb (0.23 kg)] Weight with cable tray [within ± 0.5 lb (0.23 kg)] Specifications 8.2 in. (20.8 cm) 5.6 in. (14.2 cm) 1.3 in. (3.3 cm) 1.8 in. (4.6 cm) 1.25 lb (0.57 kg) 1.41 lb (0.64 kg) I-240G-C ONT when installed inside an outdoor enclosure Height Width Depth Weight 13.5 in. (34.3 cm) 12 in. (30.5 cm) 4.3 in. (10.9 cm) lb ( kg) Table 32-8 lists power consumption specifications for I-240G-B, I-241G-B, and I-240G-C indoor ONTs. Table 32-8 I-240G-B, I-241G-B, and I-240G-C indoor ONT power consumption specifications Mnemonic Maximum power (not to exceed) Condition Minimum power Condition I-240G-B 7.75 W 2 POTS off-hook, 4 Gig-E operational I-240G-C 7.75 W 2 POTS off-hook, 4 Gig-E operational I-241G-B 10 W 2 POTS off-hook, 4 Gig-E, Video operational 4.75 W 2 POTS on-hook, other interfaces/services not provisioned 4.75 W 2 POTS on-hook, other interfaces/services not provisioned 4.75 W 2 POTS on-hook, other interfaces/services not provisioned Table 32-9 lists the environmental requirements for I-240G-B, I-241G-B, and I-240G-C indoor ONTs. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

97 32 I-240G-B, I-241G-B, and I-240G-C unit data sheet Table 32-9 I-240G-B, I-241G-B, and I-240G-C indoor ONT environmental requirements ONT type Mounting method Temperature range and humidity Altitude Desk or wall mounted Operating: 32 F to 104 F (0 C to 40 C) ambient temperature 5% to 85% relative humidity, non-condensing Maximum rate of temperature change is 32.9 F (18.3 C) per hour Operating for the temperature-hardened I-240G-C ONT: 40 F to 140 F ( 40 to 60 C) ambient temperature Storage: -13 F to 133 F (-25 C to 55 C) 5% to 93% relative humidity, non-condensing Maximum operating altitude is ft (3048 m) above mean sea level Maximum non-operating altitude is ft ( m) above mean sea level 32.7 I-240G-B, I-241G-B and I-240G-C GEM ports and T-CONTs Table lists the maximum number of supported T-CONTs and GEM ports for I-240G-B, I-241G-B, and I-240G-C indoor ONTs. Not all ONTs will be supported in all of the releases indicated the table. See the appropriate release Customer Release Notes for the most accurate list of supported devices. Table I-240G-B, I-241G-B, and I-240G-C indoor ONT capacity for GEM ports and T-CONTs per package and release ONT or MDU Release Maximum Notes Package B ONTs GEM ports per indoor or outdoor ONT T-CONTs per indoor or outdoor ONT All are present: 30 are available, 2 are reserved for multicast and debugging All are present: 31 are available, 1 is reserved for OMCI 32.8 I-240G-B, I-241G-B, and I-240G-C power support The following power supplies support the I-240G-B and I-241G-B indoor ONTs. Click on the link for more information. Delta DUPS-1215 UPS unit data sheet Emerson 24 W AC/DC switching power adapter unit data sheet The I-240G-C is also supported by these power supplies, among others. For more detailed information about power support, refer to Table 2-2 in chapter 2, Part numbers, ordering, and deployment configuration overview November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

98 32 I-240G-B, I-241G-B, and I-240G-C unit data sheet 32.9 I-240G-B, I-241G-B, and I-240G-C functional blocks POTS and RF video ports may or may not be available in addition to Ethernet ports. These ONTs transmit Ethernet packets to four RJ-45 Ethernet ports, and voice traffic to two RJ-11 POTS ports and RF video traffic to one F-type coaxial connector. These ONTs also feature fiber optic and power connectors. Figure 32-5 shows the functional blocks for an indoor ONT with Gigabit Ethernet, POTS, and coaxial ports. For those ONTs with fewer than the maximum number of Gigabit Ethernet or POTS ports, the excess ports are blocked by a plastic cover. Figure 32-5 Single-residence Gigabit Ethernet ONT with POTS and RF video Power Converter Power connector GPON Optical block SOC POTS (2/1/0) Ethernet (4/1) RJ-11 RJ-45 RF Video Amp Diplexer F-type connector I-240G-B, I-241G-B, and I-240G-C standards compliance I-240G-B, I-241G-B, and I-240G-C indoor ONTs are compliant with the following standards: 802.1p mapper service profile on the upstream G.984 support for GPON interface (framing) G support for activation with automatic discovery of a serial number and a password G984.4 (standard and revised) support for OMCI interface for ONT management and provisioning I-240G-B, I-241G-B, and I-240G-C special considerations IGMP packet replication allows the I-240G-B, I-241G-B, and I-240G-C indoor ONTs to support IPTV on all four Ethernet channels at the same time. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

99 32 I-240G-B, I-241G-B, and I-240G-C unit data sheet On a user-side port in flexible mode, downstream multicast traffic will have the UNI-side p-bit of the parameter DATAPRI configured for the IGMP signaling channel, unless the DATAPRI value differs between ONT UNIs. In the latter case, the downstream multicast traffic will retain the p-bit from the PON. On a user-side port in non-flexible mode, such as translation mode, downstream multicast traffic will retain the p-bit from the PON. The multicast VLAN ID may differ; see Table for tagging behavior. Table Multicast downstream VLAN tagging for I-240G-B, I-241G-B, and I-240G-C indoor ONTs Port configuration (1) One port configured in flexible mode or VLAN translation mode with a configured IGMP signaling channel More than one port configured in flexible mode or VLAN translation mode each with a configured IGMP signaling channel VLAN tagging of downstream multicast traffic Multicast traffic is tagged with UNI-side VLAN ID of IGMP-related service. If the IGMP-related services are configured with the same UNI-side VLAN ID, then all multicast traffic is tagged with the UNI-side VLAN ID of their service. If the IGMP-related services are configured with different UNI-side VLAN IDs, then all multicast traffic is tagged with VLAN ID More than one port configured in VLAN pass-through mode, untrusted mode, EtherType/VLAN translation mode, or EtherType classification mode with some ports in transmit with tag and other ports in transmit without a tag, and each port with a configured IGMP signaling channel All other cases The multicast traffic is tagged with VLAN ID The multicast traffic retains the VLAN ID from the PON. Note (1) You can only have one IGMP signaling channel on a port. Service creation considerations and limitations Port-to-port mode must be enabled when using four-port Ethernet ONTs I-240G-B, I-241G-B, and I-240G-C. When using port-to-port mode, you can only configure one Ethernet port. Upgrade considerations and limitations Existing ONTs that use 7342 ISAM FTTU releases older than R04.06.xx and R04.07.xx must be upgraded to use R software while assigned to a PON ID value smaller than 64. For this purpose, if split ratios larger than 1:64 are being deployed, you may choose to set aside the first PON ID as a staging point November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

100 32 I-240G-B, I-241G-B, and I-240G-C unit data sheet I-240G-B, I-241G-B, and I-240G-C ONT considerations and limitations When using multicast on multiple Ethernet ports, all Ethernet ports must have the same VLAN ID. If the user-side VLAN IDs are all given the same VLAN ID, a common VLAN ID should result. If not, VLAN 4094 will be used ONTs are not able to sufficiently buffer enough traffic between grants to support an EIR rate of 1Gb/s over multiple GEM ports. There are only Gb/s buffers available in the SoC chip. The buffers are divided among the number of configured GEM ports. Reducing the number of GEM ports configured results in increased upstream buffering and higher upstream traffic rates. Packets with less than 72 bytes are increased to exactly 72 bytes in size with padding ONTs that use pre R software may not range if the distance from the LT card is less than 1km The call park feature is not supported on this device. The default optical thresholds for these ONTs are as follows: Low optical threshold: dbm High optical threshold: dbm Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

101 32 I-240G-B, I-241G-B, and I-240G-C unit data sheet November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

102 NTP 172 Install an I-240G-B, I-241G-B, or I-240G-C indoor ONT Purpose This NTP provides the steps to install an I-240G-B, I-241G-B, or I-240G-C indoor ONT. General The DLPs listed in this NTP describe mounting and cabling for the I-240G-B, I-241G-B, and I-240G-C indoor ONTs. Prerequisites See the listed DLPs for prerequisites. Recommended tools You need the following tools for the installation: #2 Phillips screwdriver 1/4 in. (6 mm) flat blade screwdriver wire strippers fiber optic splicing tools RJ-45 cable plug crimp tool voltmeter or multimeter optical power meter wall mounting template Fair-Rite (1AB ) ferrite core shipped with the ONT drill and drill bits Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November 2013 NTP FE AAAA TCZZA Edition 01

103 NTP 172 Install an I-240G-B, I-241G-B, or I-240G-C indoor ONT Safety information Read the following safety information before installing the unit. Danger 1 Contact the local utility company before you connect the enclosure to the utilities. Danger 2 Observe the local and national laws and regulations that may be applicable to this installation. Danger 3 If the coaxial output of the ONT is connected to the dwelling infrastructure coaxial distribution system, ensure that the coaxial distribution system is separately grounded. Grounding of the dwelling coaxial infrastructure shall use Listed grounding devices and must be installed in accordance with local Codes and Article 800 of the National Electric Code, ANSI/NFPA 70, following the manufacturers instructions. Warning 1 This equipment is ESD sensitive. Proper ESD protections should be used when removing the fiber access cover of the indoor ONT. Warning 2 Installation of the supplied ferrite on the Ethernet cable is required for EMC compliance. Failure to install the supplied ferrite core may cause interference with TV or radio reception. Alcatel-Lucent is not responsible for any radio or television interference caused by using other than the supplied ferrite core or by unauthorized changes or modifications to this equipment. Unauthorized changes or modifications could void the user s authority to operate this equipment. Caution Keep indoor ONTs out of direct sunlight. Prolonged exposure to direct sunlight can damage the unit. Note Observe the following: The indoor ONT should be installed in accordance with the applicable requirements of the NEC or CEC. Local authorities and practices take precedent when there is conflict between the local standard and the NEC or CEC. The indoor ONT must be installed by qualified service personnel. Indoor ONTs must be installed with cables that are suitably rated and listed for indoor use. See I-240G-B, I-241G-B, and I-240G-C detailed specifications in the I-240G-B, I-241G-B, and I-240G-C unit data sheet for the temperature ranges for ONTs. NTP November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

104 NTP 172 Install an I-240G-B, I-241G-B, or I-240G-C indoor ONT Procedure Use this procedure to install an I-240G-B, I-241G-B, or I-240G-C indoor ONT. 1 Prepare the cables at the site where the ONT will be installed (DLP 100). 2 Are any of the cables missing? a If yes, go to step 3. b If no, go to step 5. 3 Locate each missing cable and route them to the ONT as per local practices. 4 Place the indoor ONT unit: a On a flat surface, go to step 5. b In a stand mount, go to step 6. c On a wall, go to DLP 122. d In an outdoor enclosure (I-240G-C only), go to step 7. 5 Place the indoor ONT on the flat surface, such as a desk, horizontally resting on its four feet as shown in Figure NTP 172-1; go to step 11. Figure NTP 172-1: I-240G-B or I-241G-B indoor ONT on a desk VIDEO VOICE LAN 4 LAN 2 LAN 1 LAN 3 ALARM POWER WAN 6 Place the indoor ONT in the stand mount i ii Place the stand mount on the flat surface. Place the ONT into the opening on the stand mount, ensuring it is securely held. Figure NTP shows the stand mount. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November 2013 NTP FE AAAA TCZZA Edition 01

105 WAN NTP 172 Install an I-240G-B, I-241G-B, or I-240G-C indoor ONT Figure NTP 172-2: I-240G-B or I-241G-B ONT in a stand mount VIDEO VOICE LAN 4 LAN 3 LAN 2 LAN 1 ALARM POWER iii Go to step 11. NTP November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

106 NTP 172 Install an I-240G-B, I-241G-B, or I-240G-C indoor ONT 7 Wall-mount the outdoor enclosure for the I-240G-C indoor ONT. a Note For I-240G-C ONTs installed in an outdoor enclosure, a label supplied with the enclosure must be attached to the surface of the ONT to label the LEDs as documented in I-240G-B, I-241G-B, and I-240G-C LEDs in the UDS. Apply the label on the top surface of the ONT near to the LEDs so that the Power label aligns with the first LED. The text on the label should be legible (right-side up) when the ONT is installed in the enclosure and the unit is wall-mounted (see Figure NTP 172-5). If you are using a fiber-slack storage tray (FSST) (3EM AA): i Secure the FSST (3EM AA) to the mounting area. Use the appropriate hardware as defined by local installation practices. Use the cable storage compartment mounting holes; see Figure NTP Figure NTP 172-3: Mounting the cable storage compartment (3EM AA) Bracket mounting point Cable storage compartment mounting hole slot Bracket mounting point Cable storage compartment mounting hole Cable storage compartment mounting hole Bracket mounting point Bracket mounting point ii Remove either the aerial or buried cable entry grommet; see Figure NTP Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November 2013 NTP FE AAAA TCZZA Edition 01

107 NTP 172 Install an I-240G-B, I-241G-B, or I-240G-C indoor ONT Figure NTP 172-4: Coiled cable routing (open view) Grommet Grommet Aerial cable entry point (optional) Buried cable entry point Coil retention clip Cable feeds to ONT (actual length varies, but a minimum of approximately 18 in.) iii iv Cut the width of the cable off of the end of the grommet. Reinstall the grommet into the slot over the cable v Coil the excess cable in a clockwise direction, allowing enough cable to exit the lower right cable exit port; see Figure NTP vi Note 1 There must be adequate length for the fiber optic cable to curve around and maintain minimum bend radius, enter into the ONT enclosure and make the optical connection. Note 2 There must be approximately 20 in. (50 cm) of cable exiting the FSST at the right cable exit point. Note 3 The FSST stores a maximum of 75 ft (22.86 m) of cable. Secure the fiber optic cable with the coil retention clamp; see Figure NTP NTP November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

108 NTP 172 Install an I-240G-B, I-241G-B, or I-240G-C indoor ONT vii Bolt the outdoor enclosure to the four mounting points on the cable storage compartment using the supplied #8-16 X 1/2 self tapping screws; see Figure NTP and NTP viii Go to step 10. b If you are not using an FSST: i Open the access cover on the outdoor enclosure by loosening the pin-in-hex screw. Note The access cover of the outdoor enclosure must be open to access the three mounting holes used to secure the outdoor enclosure to the wall. ii Secure the outdoor enclosure to the mounting area at the subscriber premises. Use the appropriate hardware as defined by local installation practices. Mount the outdoor enclosure using the specified mounting holes as shown in Figure NTP Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November 2013 NTP FE AAAA TCZZA Edition 01

109 NTP 172 Install an I-240G-B, I-241G-B, or I-240G-C indoor ONT Figure NTP 172-5: Mounting the outdoor enclosure for the I-240G-C indoor ONT Mounting hole ONT bracket Mounting hole POWER WAN ALARM LAN 1 LAN 2 LAN 3 LAN 4 VOICE VIDEO ONT bracket Mounting hole If used, place the power adapter cable (3MV AA) under the I-240G-C ONT in the outdoor enclosure as shown in Figure NTP The power adapter cable can be routed above or below the ONT and the power cable can be routed into the outdoor enclosure through either of the cable input openings depending on the length of the power cable. NTP November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

110 NTP 172 Install an I-240G-B, I-241G-B, or I-240G-C indoor ONT Figure NTP 172-6: Outdoor enclosure with power adapter cable (3FE AD only) Fiber optic cable Fiber strain relief 9 Place the fiber optic cable inside the wall-mounted outdoor enclosure as shown in Figure NTP Tie wrap the cable at the fiber optic strain relief if necessary Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November 2013 NTP FE AAAA TCZZA Edition 01

111 NTP 172 Install an I-240G-B, I-241G-B, or I-240G-C indoor ONT Figure NTP 172-7: Outdoor enclosure with fiber optic cable Fiber cable Fiber strain relief Secure the I-240G-C indoor ONT in the wall-mounted outdoor enclosure. a b Turn the brackets to the open position and position the I-240G-C indoor ONT within the outdoor enclosure and between the ONT brackets, as shown in Figure NTP Secure the I-240G-C indoor ONT within the ONT brackets by turning the brackets to the closed position. Warning Do not overtighten the ONT bracket when securing the I-240G-C indoor ONT to the outdoor enclosure. The unit can become skewed and compromise the environmental seal of the ONT mounted in the outdoor enclosure. 11 Review the connection locations shown in Figures NTP for I-240G-B and I-241G-B indoor ONTs and NTP for I-240G-C indoor ONTs installed in an outdoor enclosure. NTP November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

112 NTP 172 Install an I-240G-B, I-241G-B, or I-240G-C indoor ONT Figure NTP 172-8: I-241G-B indoor ONT connections Power connector TV U SB 1 2 POTS1 POTS2 LAN1 LAN2 LAN3 LAN4 POWER SC/APC connector RF video coaxial connector POTS connectors (RJ-11) Ethernet connectors (RJ-45) On/off button Figure NTP shows the I-241G-B indoor ONT connections. The I-240G-B ONT is identical except it does not feature an RF video coaxial connector. Figure NTP 172-9: I-240G-C indoor ONT connections POWER WAN ALARM SC/APC connector Power connector On/Off button LAN 1 LAN 2 Ethernet connectors (RJ-45) LAN 3 LAN 4 VOICE POTS connectors (RJ-11) VIDEO POTS screw terminals (3FE AD only) Connect the Ethernet cables to the RJ-45 ports (DLP 101). Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November 2013 NTP FE AAAA TCZZA Edition 01

113 NTP 172 Install an I-240G-B, I-241G-B, or I-240G-C indoor ONT 13 Connect the POTS cables (DLP 123). 14 For the I-241G-B ONT only, connect the coaxial cable (DLP 116). 15 Is the fiber optic cable connected to: a an OptiTap adaptor (I-240G-C only), go to step 16. b an SC/APC adaptor, go to step 17. Warning Be careful to maintain a bend radius of no less than 1.5 inches (3.8 cm) when connecting the fiber optic cable. Too small of a bend radius in the cable can result in damage to the optic fiber. 16 Connect the fiber optic cable with an OptiTap adaptor to the I-240G-C indoor ONT. i Route the fiber optic cable to the ONT. ii Plug the OptiTap adaptor into the fiber optic port (DLP 124). iii Go to step Connect the SC/APC fiber optic cable (DLP 125). 18 Install the power supply according to manufacturer specifications. Caution Units must be powered by a Listed or CE approved and marked limited power source power supply with a minimum output rate of 12 V dc, 1.25 A. 19 Connect the power cable with an 8-pin Molex connector to the ONT unit. 20 Power up the ONT unit by using the ON/OFF power switch. 21 If necessary, reset the ONT (DLP 126). 22 Verify the ONT LEDs, voltage status, and optical signal levels (DLP 127). 23 Activate and test the services (DLP 128). 24 If used, configure the SLID (DLP 129). 25 For an I-240G-C indoor ONT installed in an outdoor enclosure, close the access cover of the outdoor enclosure and secure using the pin-in-hex screw. 26 STOP. This procedure is complete. NTP November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

114 NTP 173 Replace an I-240G-B, I-241G-B, or I-240G-C indoor ONT Purpose This NTP provides the steps to replace an I-240G-B, I-241G-B, or I-240G-C indoor ONT. General The DLPs listed in this NTP describe mounting and cabling for the I-240G-B, I-241G-B, or I-240G-C indoor ONT. Prerequisites See the listed DLPs for prerequisites. Recommended tools You need the following tools for replacing the ONT: #2 Phillips screwdriver 1/4 in. (6 mm) flat blade screwdriver wire strippers fiber optic splicing tools RJ-45 cable plug crimp tool voltmeter or multimeter optical power meter wall mounting template Fair-Rite (1AB ) ferrite core shipped with the ONT drill and drill bits Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November 2013 NTP FE AAAA TCZZA Edition 01

115 NTP 173 Replace an I-240G-B, I-241G-B, or I-240G-C indoor ONT Safety information Read the following safety information before replacing the unit. Danger 1 Contact the local utility company before you connect the enclosure to the utilities. Danger 2 Observe the local and national laws and regulations that may be applicable to this installation. Danger 3 If the coaxial output of the ONT is connected to the dwelling infrastructure coaxial distribution system, ensure that the coaxial distribution system is separately grounded. Grounding of the dwelling coaxial infrastructure shall use Listed grounding devices and must be installed in accordance with local Codes and Article 800 of the National Electric Code, ANSI/NFPA 70, following the manufacturers instructions. Warning 1 This equipment is ESD sensitive. Proper ESD protections should be used when removing the fiber access cover of the indoor ONT. Warning 2 Installation of the supplied ferrite on the Ethernet cable is required for EMC compliance. Failure to install the supplied ferrite core may cause interference with TV or radio reception. Alcatel-Lucent is not responsible for any radio or television interference caused by using other than the supplied ferrite core or by unauthorized changes or modifications to this equipment. Unauthorized changes or modifications could void the user s authority to operate this equipment. Caution Keep indoor ONTs out of direct sunlight. Prolonged exposure to direct sunlight can damage the unit. Note 1 The indoor ONT should be installed in accordance with the applicable requirements of the NEC or CEC. Local authorities and practices take precedent when there is conflict between the local standard and the NEC or CEC. Note 2 The indoor ONT must be installed by qualified service personnel. Note 3 Indoor ONTs must be installed with cables that are suitably rated and listed for indoor use. Note 4 See I-240G-B, I-241G-B, and I-240G-C detailed specifications in the I-240G-B, I-241G-B, and I-240G-C unit data sheet for the temperature ranges for ONTs. NTP November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

116 NTP 173 Replace an I-240G-B, I-241G-B, or I-240G-C indoor ONT Procedure Use this procedure to replace an I-240G-B, I-241G-B, or I-240G-C indoor ONT. 1 Deactivate the ONT services (DLP 131). If you are using the SLID feature, this step is not required. The ONT and the services can remain in service (IS). 2 Power down the ONT unit by using the ON/OFF power switch. 3 Disconnect the POTS, Ethernet, coaxial, and power cables from the ONT (DLP 132); see Figures NTP 173-1, NTP 173-2, and NTP Figure NTP 173-1: I-240G-B indoor ONT connections Power connector U SB 1 2 POTS1 POTS2 LAN1 LAN2 LAN3 LAN4 POWER Fiber optic connector Phone connectors (RJ-11) Ethernet ports (RJ-45) On/off Figure NTP 173-2: I-241G-B indoor ONT connections Power connector TV U SB 1 2 POTS1 POTS2 LAN1 LAN2 LAN3 LAN4 POWER SC/APC connector RF video coaxial connector POTS connectors (RJ-11) Ethernet connectors (RJ-45) On/off button Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November 2013 NTP FE AAAA TCZZA Edition 01

117 NTP 173 Replace an I-240G-B, I-241G-B, or I-240G-C indoor ONT Figure NTP 173-3: I-240G-C ONT connections POWER WAN ALARM SC/APC connector Power connector On/Off button LAN 1 LAN 2 Ethernet connectors (RJ-45) LAN 3 LAN 4 VOICE POTS connectors (RJ-11) VIDEO POTS screw terminals (3FE AD only) Disconnect the SC/APC adaptor from the fiber optic connector on the ONT (DLP 133); see Figures NTP and NTP Replace the ONT with a new unit: a b On a flat surface, such as a desk, substitute a replacement ONT for the old ONT; go to step 6. In a stand. i ii Unsnap the old ONT from the channels built into the stand. Snap the new ONT into channels built into the stand, ensuring it is securely held. Place the replacement ONT with stand vertically on a flat surface; go to step 6. NTP November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

118 NTP 173 Replace an I-240G-B, I-241G-B, or I-240G-C indoor ONT c On a wall. i ii Slide the old ONT upward and then away from the two mounting screws until the ONT is free of the wall. Slide the wall mount keyholes on the ONT enclosure or fiber storage tray of the replacement ONT down over the mounting screws until it is securely seated. d For an I-240G-C indoor ONT in a wall-mounted outdoor enclosure. i Unfasten the I-240G-C indoor ONT by turning the brackets to the open position (as shown in Figure NTP 173-4) and remove the unit. Figure NTP 173-4: I-240G-C indoor ONT mounted in an outdoor enclosure Mounting hole ONT bracket Mounting hole POWER WAN ALARM LAN 1 LAN 2 LAN 3 LAN 4 VOICE VIDEO ONT bracket Mounting hole Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November 2013 NTP FE AAAA TCZZA Edition 01

119 NTP 173 Replace an I-240G-B, I-241G-B, or I-240G-C indoor ONT ii Position the replacement I-240G-C indoor ONT within the outdoor enclosure and between the ONT brackets, as shown in Figure NTP iii Note For I-240G-C ONTs installed in an outdoor enclosure, a label supplied with the enclosure must be attached to the surface of the ONT to label the LEDs as documented in Indoor (I-series) ONT LEDs in the Product Information Manual. Apply the label on the top surface of the ONT near to the LEDs so that the Power label aligns with the first LED. The text on the label should appear right-side up for reading when the ONT is installed in the enclosure and the unit is wall-mounted (see Figure NTP 173-4). Secure the I-240G-C indoor ONT by turning the brackets to the closed position. Warning Do not overtighten the ONT bracket when securing the I-240G-C indoor ONT to the outdoor enclosure. The unit can become skewed and compromise the environmental seal of the ONT mounted in the outdoor enclosure. 6 Connect the Ethernet cables (DLP 101). 7 Connect the POTS cables (DLP 123). 8 For I-241G-B ONTs only, connect the coaxial cable (DLP 116). 9 If required, have approved service personnel who are trained to work with optic fiber clean the fiber optic connection. See DLP 134 for more information about fiber optic handling, inspection, and cleaning. Danger Fiber optic cables transmit invisible laser light. To avoid eye damage or blindness, never look directly into fibers, connectors, or adapters. 10 Is the fiber optic cable connected to: a an OptiTap adaptor (I-240G-C in outdoor enclosure only), go to step 11. b an SC/APC adaptor, go to step 12. Warning Be careful to maintain a bend radius of no less than 1.5 inches (3.8 cm) when connecting the fiber optic cable. Too small of a bend radius in the cable can result in damage to the optic fiber. 11 Connect the fiber optic cable to the I-240G-C indoor ONT. i Route the fiber optic cable to the ONT. ii Plug the OptiTap adaptor into the fiber optic port (DLP 124). iii Go to step 13. NTP November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

120 NTP 173 Replace an I-240G-B, I-241G-B, or I-240G-C indoor ONT 12 Connect the fiber optic cable to the ONT. i Route the fiber optic cable to the ONT. ii Plug the SC/APC adaptor into the fiber optic port (DLP 125). 13 Install the power supply according to manufacturer specifications. Warning Units must be powered by a Listed or CE approved and marked limited power source power supply with a minimum output rate of 12 V dc, 1.25 A. 14 Connect the power cable with an 8-pin Molex connector to the ONT unit. 15 For an I-240G-C indoor ONT installed in an outdoor enclosure with an FSST, coil the excess cable in a clockwise direction allowing it to exit the lower right cable exit port; see Figure NTP Note Observe the following: There must be approximately 18 in. (45.72 cm) of cable stub exiting the FSST at the right cable exit point. The FSST stores a maximum of 75 ft (22.86 m) of cable. 16 Power up the ONT unit by using the ON/OFF power switch. 17 If necessary, reset the ONT (DLP 126). 18 If used, configure the SLID (DLP 129). Note A new SLID or the old SLID may be used with the replacement ONT. If a new SLID is used, the new SLID must also be programmed at the P-OLT using TL1 or a network manager. If the old SLID is used, no changes need to be made at the P-OLT; see the operations and maintenance documentation for the OLT for more details. 19 Verify the ONT LEDs, voltage status, and optical signal levels (DLP 127). 20 Activate and test the services (DLP 128). 21 For an I-240G-C indoor ONT installed in an outdoor enclosure, close the access cover of the outdoor enclosure and secure using the pin-in-hex screw. 22 STOP. This procedure is complete. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November 2013 NTP FE AAAA TCZZA Edition 01

121 NTP 173 Replace an I-240G-B, I-241G-B, or I-240G-C indoor ONT NTP November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

122 NTP 174 Configure an I-240G-B, I-241G-B, or I-240G-C indoor ONT General Please refer to the OLT Operations and Maintenance using TL1 and CLI guide for the software configuration procedure for an I-240G-B, I-241G-B, or I-240G-C indoor ONT. For HTTP configuration procedures, please refer to chapter 6, ONT management using an ONT interface. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November 2013 NTP FE AAAA TCZZA Edition 01

123 NTP 174 Configure an I-240G-B, I-241G-B, or I-240G-C indoor ONT NTP November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

124 I-120G-B, I-240G-D 33 I-120G-B and I-240G-D unit data sheet NTP 175 Install an I-120G-B or I-240G-D indoor ONT NTP 176 Replace an I-120G-B or I-240G-D indoor ONT NTP 177 Configure an I-120G-B or I-240G-D indoor ONT Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

125 November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

126 33 I-120G-B and I-240G-D unit data sheet 33.1 I-120G-B and I-240G-D part numbers and identification I-120G-B and I-240G-D general description I-120G-B and I-240G-D software and installation feature support I-120G-B and I-240G-D interfaces and interface capacity I-120G-B and I-240G-D LEDs I-120G-B and I-240G-D detailed specifications I-120G-B and I-240G-D GEM ports and T-CONTs I-120G-B and I-240G-D power support I-120G-B and I-240G-D functional blocks I-120G-B and I-240G-D standards compliance I-120G-B and I-240G-D special considerations Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

127 33 I-120G-B and I-240G-D unit data sheet 33.1 I-120G-B and I-240G-D part numbers and identification Table 33-1 provides part numbers and identification information for I-120G-B and I-240G-D indoor ONT. Table 33-1 I-120G-B and I-240G-D part numbers and identification Mnemonic Ordering kit part number Provisioning part number Description CLEI CPR ECI/ Bar code I-120G-B 3FE AA GPON I-series ONT unit, version B, 2 Ethernet interfaces, 1 POTS interface, SC/APC connector. Includes ac/dc power cord with European (EU) variant plug (1 of 2) 33-2 November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

128 33 I-120G-B and I-240G-D unit data sheet Mnemonic Ordering kit part number Provisioning part number Description CLEI CPR ECI/ Bar code I-240G-D 3FE AA 3FE AB GPON I-series ONT unit, version D, 4 Ethernet interfaces, 2 POTS interfaces, SC/APC connector. Includes 3-pin desktop ac/dc adaptor with European (EU) variant plug. 3FE AB GPON I-series ONT unit, version D, 4 Ethernet interfaces, 2 POTS interfaces, SC/APC connector. Includes 2-pin wall-mounted ac/dc adaptor with European (EU) variant plug. 3FE BA GPON I-series ONT unit, version D, 4 Ethernet interfaces, 2 POTS interfaces, SC/APC connector. Includes ac/dc power cord with Australian (AU) variant plug. 3FE CA GPON I-series ONT unit, version D, 4 Ethernet interfaces, 2 POTS interfaces, SC/APC connector. Includes 3-pin wall-mounted ac/dc adaptor with United Kingdom (UK) variant plug. 3FE CB customer-specific 3FE DA customer-specific GPON I-series ONT unit, version D, 4 Ethernet interfaces, 2 POTS interfaces, SC/APC connector. Includes ac/dc power cord with United Kingdom (UK) variant plug. GPON I-series ONT unit, version D, 4 Ethernet interfaces, 2 POTS interfaces, SC/APC connector. Includes 3-pin wall-mounted ac/dc adaptor with US variant plug. 3FE DB GPON I-series ONT unit, version D, 4 Ethernet interfaces, 2 POTS interfaces, SC/APC connector. Includes 3-pin wall-mounted ac/dc adaptor with US variant plug and RJ-11. RJ45 and SC/APC cables. 3FE CA 3FE AB GPON I-series ONT unit, version D, 4 Ethernet interfaces, 2 POTS interfaces, SC/UPC connector. Includes ac/dc power cord with China (CCC) variant plug (2 of 2) Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

129 33 I-120G-B and I-240G-D unit data sheet 33.2 I-120G-B and I-240G-D general description I-120G-B and I-240G-D indoor ONTs provide subscriber interfaces for the network by terminating the PON interface and converting it to user interfaces that directly connect to subscriber devices. The ONT is compatible with all existing subscriber equipment, including analog phones with both tone and rotary dial capabilities, cordless phones, modems, fax machines, and caller ID boxes (Type I, Type II, and Type III). I-120G-B and I-240G-D indoor ONTs provide the following functions: fully G.984 series GPON standard compliant IGMP snooping support for Multicast GEM port G984.4 and G standard compliant ONT Management Control Interface (OMCI) interface for ONT management and provisioning Management Information Base (MIB) manipulation over OMCI by Create, Delete, Set, Get, and Get next commands optics that support received signal strength indication (RSSI) remote software image download (as well as activation and reboot) over OMCI delivers video content in the form of data by multicast or unicast performance monitoring as well as alarms and AVC reports 33.3 I-120G-B and I-240G-D software and installation feature support Table 33-2 provides a list of software-based features and installation information supported by I-120G-B and I-240G-D indoor ONTs. Table 33-2 I-120G-B and I-240G-D indoor ONT software feature support Feature Chapter/description Click link for more information General ONT and MDU overview Service interface specifications General information common to multiple devices and an explanation of general system behaviors. ONT and MDU general and interface technical specifications ONT and MDU overview Ethernet interface specifications POTS interface specifications Services supported See the appropriate P-OLT user documentation for service creation procedures and descriptions. RSSI ONT and MDU general and interface technical specifications RSSI specifications Wi-Fi specifications Optical budget Location and installation options (1 of 2) ONT and MDU general and interface technical specifications How to install and replace an I-120G-B or I-240G-D indoor ONT ONT optical budget Install an I-120G-B or I-240G-D indoor ONT Replace an I-120G-B or I-240G-D indoor ONT 33-4 November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

130 33 I-120G-B and I-240G-D unit data sheet Feature Chapter/description Click link for more information Activation methods ONT and MDU overview SLID entry via Ethernet port HTTP management Statistics and performance monitoring Supported UPS configurations (2 of 2) Information necessary to manage an ONT at a local site using an HTTP interface, CLI interface, CLI interface, or butt set. ONT and MDU statistics and performance monitoring Part numbers, ordering, and deployment configuration overview ONT management using an ONT interface Contact your Alcatel-Lucent representative ONT and MDU to UPS or power adapter compatibility support 33.4 I-120G-B and I-240G-D interfaces and interface capacity Table 33-3 describes the supported interfaces and interface capacity for I-120G-B and I-240G-D indoor ONTs. Table 33-3 I-120G-B and I-240G-D indoor ONT interface connection capacity ONT type and model Maximum capacity POTS 10/ 100 BASE-T 10/ 100/ 1000 BASE-T RF video (CATV) MoCA VDSL2 E1/T1 Local craft GPON SC/ APC I-120G-B I-240G-D I-120G-B and I-240G-D connections and components Figure 33-1and 33-3 show the physical connections for I-120G-B indoor ONTs, Figure 33-2and 33-3 show the physical connections for I-240G-D indoor ONTs, Figure 33-1 I-120G-B indoor ONT physical connections (back view) OPTICAL TEL LAN 2 LAN 1 POWER ON/OFF Fiber optic port POTS port (RJ-11) Ethernet ports (RJ-45) Power connector On/off switch Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

131 33 I-120G-B and I-240G-D unit data sheet Figure 33-2 I-240G-D indoor ONT physical connections (back view) OPTICAL TEL1 TEL2 LAN 4 LAN 3 LAN 2 LAN 1 POWER ON/OFF Fiber optic port POTS ports (RJ-11) Ethernet ports (RJ-45) Power connector On/off switch Figure 33-3 I-120G-B and I-240G-D indoor ONT physical connections (side view) LED RESET LED button Reset button Table 33-4 describes the physical connections for I-120G-B and I-240G-D indoor ONTs. Table 33-4 I-120G-B and I-240G-D indoor ONT physical connections Connection (1) Ethernet ports Fiber optic LED button POTS Power Description This connection is provided through Ethernet RJ-45 connectors. Up to four 10/100 Base-T Ethernet interfaces are supported.the Ethernet ports can support both data and in-band video services on all interfaces. This connection is provided through an SC/APC fiber optic connector. This buttons turns all LEDs on or off. This connection is provided through RJ-11 ports. Up to two POTS connections are supported.the POTS ports support voice services. This connection is provided through the power connector. A power cable fitted with a barrel connector is used to make the connection. Note (1) The primary path for the earth ground for these ONTs is provided by the 12V Return signal in the power connector I-120G-B and I-240G-D LEDs Figure 33-4 shows the I-120G-B and I-240G-D indoor ONT LEDs November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

132 33 I-120G-B and I-240G-D unit data sheet Figure 33-4 I-120G-B and I-240G-D indoor ONT LEDs POWER OPTICAL LAN UPDATE ALM POTS POWER OPTICAL LAN UPDATE ALM POTS Table 33-5 provides LED descriptions for I-120G-B and I-240G-D indoor ONTs. Table 33-5 I-120G-B and I-240G-D indoor ONT LEDs Indicator LED color and behavior LED behavior description POWER OPTICAL LAN UPDATE ALM POTS Green solid Green flashing Off Red solid Green solid Green flashing Off Green solid Green flashing Off Red solid Green flashing Off Red solid Green solid Off Green solid Green flashing Off Operating on AC power Operating on battery power No power source Optical module power or signal loss Optical module normal; synchronized PON optical port synchronization PON optical port is not synchronized ONT local RJ-45 Ethernet interface connection is established Ethernet data link transceiver Ethernet interface is not connected Upgrade failed Upgrading Normal state Hardware exceptions Local access Normal state Off hook Off hook for more than one hour On hook Table 33-6 lists indoor ONT RJ-45 LEDs (I-120G-B and I-240G-D). Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

133 33 I-120G-B and I-240G-D unit data sheet Table 33-6 Indoor ONT RJ-45 LEDs (I-120G-B and I-240G-D) Indicator LED color and behavior LED behavior description LINK MODE Off Green solid Green flashing Off Green solid Link not detected Link active Link detected and activity present 10 and 100 Mb/s operation 1000 Mb/s operation 33.6 I-120G-B and I-240G-D detailed specifications Table 33-7 lists the physical specifications for I-120G-B indoor ONTs. Table 33-7 I-120G-B indoor ONT physical specifications Description Length Width Height Weight [within ± 0.5 lb (0.23 kg)] Specification 4.3 in. (110 mm) 5.5 in. (140 mm) 1.3 in. (33 mm) 0.5 lb (0.22 kg) Table 33-8 lists the physical specifications for I-240G-D indoor ONTs. Table 33-8 I-240G-D indoor ONT physical specifications Description Length Width Height Weight [within ± 0.5 lb (0.23 kg)] Specification 5.63 in. (143 mm) 7.09 in. (180 mm) 1.42 in. (36 mm) 0.66 lb (0.3 kg) Table 33-9 lists the power consumption specifications for I-120G-B and I-240G-D indoor ONTs. Table 33-9 I-120G-B and I-240G-D indoor ONT power consumption specifications Mnemonic Maximum power (Not to exceed) Condition Minimum power Condition I-120G-B 5.2 W POTS off-hook, 2 10/100/1000 Base-T Ethernet 4.1 W POTS on-hook, other interfaces/services not provisioned (1 of 2) 33-8 November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

134 33 I-120G-B and I-240G-D unit data sheet Mnemonic Maximum power (Not to exceed) Condition Minimum power Condition I-240G-D 9 W 2 POTS off-hook, 4 10/100/1000 Base-T Ethernet 4.5 W 2 POTS on-hook, other interfaces/services not provisioned (2 of 2) Table lists the environmental specifications for I-120G-B and I-240G-D indoor ONTs. Table I-120G-B and I-240G-D indoor ONT environmental specifications Mounting method Temperature range and humidity Altitude I-120G-B on desk or wall mounted I-240G-D on desk or wall mounted Operating: 32 F to 113 F (0 C to 45 C) ambient temperature 10% to 90% relative humidity, non-condensing Storage: Contact your Alcatel-Lucent support representative for more information Operating: 23 F to 113 F (-5 C to 45 C) ambient temperature 10% to 90% relative humidity, non-condensing Storage: Contact your Alcatel-Lucent support representative for more information Contact your Alcatel-Lucent technical support representative for more information Contact your Alcatel-Lucent technical support representative for more information 33.7 I-120G-B and I-240G-D GEM ports and T-CONTs Table lists the maximum number of supported T-CONTs and GEM ports. See the appropriate release Customer Release Notes for the most accurate list of supported devices. Table I-120G-B and I-240G-D indoor ONT capacity for GEM ports and T-CONTs ONT or MDU Release Maximum Notes Package L ONTs GEM ports per indoor or outdoor ONT T-CONTs per indoor or outdoor ONT All 256 All I-120G-B and I-240G-D power support For the I-120G-B and I-240G-D indoor ONT, contact your Alcatel-Lucent technical support representative for more information. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

135 33 I-120G-B and I-240G-D unit data sheet 33.9 I-120G-B and I-240G-D functional blocks I-120G-B and I-240G-D indoor ONTs are single-residence ONTs. These ONTs transmit Ethernet packets to up to four RJ-45 Ethernet ports and voice traffic to up to two RJ-11 POTS ports. These ONTs also feature fiber optic and power connectors. Figure 33-5 shows the functional blocks for I-120G-B and I-240G-D indoor ONT. Figure 33-5 Single-residence ONT with Gigabit Ethernet and POTS and without RF video Power converter Power connector GPON Optical block SOC POTS Ethernet RJ-11 RJ ONT SoC technology serves as the main hardware block for these ONTs; see Figure Figure 33-6 Package L ONT hardware block POTS ports Control processor SoC DSP SoC Bridge Ethernet MACs GPON MAC Ethernet ports GPON ONT SoC technology consists of five key elements: GPON MAC The Gigabit Passive Optical Network Media Access Control (GPON MAC) element on the SoC terminates the GPON interface using an optical diplexer. This interface supports GPON as described in G (GPON TC Layer) ITU specification November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

136 33 I-120G-B and I-240G-D unit data sheet Ethernet MAC The SoC provides up to four GE MACs. DSP interface The Digital Signal Processor (DSP) provides voice processing for up to 2 POTS lines with 3-way calling. The DSP has a dedicated 64 kbyte instruction cache and shares a 32 kbyte data cache with the Control Processor. It provides up to 4 network processor cores, each at 800MHz. Control Processor The Control Processor features an integral memory management unit that supports a dedicated 64 kbyte instruction cache and shares a single 32 kbyte data cache with the DSP. The Control Processor and DSP also include a single channel Data Management Application (DMA) controller with a 4 kbyte read ahead low-latency Dynamic Random Access Memory (DRAM) access port. The processors typically run at 500 MHz. Switch matrix The Switch matrix provides an integrated data channel between the four GE MACs, the GPON MAC, the DSP, the control processor, and the other integrated elements such as flash memory, DRAM, and the local bus controller. These ONTs can also interact with additional hardware components to support functionality not provided by the SoC technology I-120G-B and I-240G-D standards compliance I-120G-B and I-240G-D indoor ONTs are compliant with the following standards: 802.1p marking and VLAN based pbit is supported G.711 support for FAX and modem connection G.984 support GPON interface (framing) G support for Amd1, class B+ G support for activation and password functions G support for AES with operator enable/disable on per port-id level G support for FEC in both upstream and downstream directions G support for multicast using a single GEM Port-ID for all video traffic G984.4 and G support for OMCI interface for ONT management and provisioning I-120G-B and I-240G-D special considerations Procedure 33-1 Login to web-based GUI 1 Open a web browser and enter the IP address of the ONT in the address bar. The login window appears. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

137 33 I-120G-B and I-240G-D unit data sheet The default gateway IP address is You can connect to this IP address using your web browser after connecting your PC to one of Ethernet ports of the ONT. The static IP address of your PC must be in the same subnet as the ONT. 2 Enter your username and password in the Log in window. The default username is usradmin and the default password is usradmin. Caution If you reset the router to recover the default username and password, all other router configuration settings will also be restored to their factory default values. Note If you forget the current username and password, press the reset button for 5 s and the default values for the username and password will be recovered at startup. 3 Click Login. 4 STOP. This procedure is complete November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

138 NTP 175 Install an I-120G-B or I-240G-D indoor ONT Purpose This NTP provides the steps to install an I-120G-B or I-240G-D indoor ONT. General The DLPs listed in this NTP describe mounting and cabling for I-120G-B or I-240G-D indoor ONTs. Prerequisites See the listed DLPs for prerequisites. Recommended tools You need the following tools for the installation: #2 Phillips screwdriver 1/4 in. (6 mm) flat blade screwdriver wire strippers fiber optic splicing tools RJ-45 cable plug crimp tool voltmeter or multimeter optical power meter drill and drill bits Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November 2013 NTP FE AAAA TCZZA Edition 01

139 NTP 175 Install an I-120G-B or I-240G-D indoor ONT Safety information Read the following safety information before installing the unit. Danger 1 Contact the local utility company before you connect the enclosure to the utilities. Danger 2 Observe the local and national laws and regulations that may be applicable to this installation. Warning This equipment is ESD sensitive. Proper ESD protections should be used when removing the fiber access cover of the indoor ONT. Caution Keep indoor ONTs out of direct sunlight. Prolonged exposure to direct sunlight can damage the unit. Procedure Note Observe the following: The indoor ONT should be installed in accordance with the applicable requirements of the NEC or CEC. Local authorities and practices take precedent when there is conflict between the local standard and the NEC or CEC. The indoor ONT must be installed by qualified service personnel. Indoor ONTs must be installed with cables that are suitably rated and listed for indoor use. See the detailed specifications in the I-120G-B and I-240G-D unit data sheet for the temperature ranges for these ONTs. Use this procedure to install an I-120G-B or I-240G-D indoor ONT. 1 Prepare the cables at the site where the ONT will be installed (DLP 100). 2 Are any of the cables missing? a If yes, go to step 3. b If no, go to step 4. 3 Locate each missing cable and route them to the ONT as per local practices. NTP November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

140 NTP 175 Install an I-120G-B or I-240G-D indoor ONT 4 Place the indoor ONT unit: a On the flat surface, such as a desk. Note The I-120G-B and I-240G-D cannot be stacked with another ONT or with other equipment. The ONT mounting requirements are: allow a minimum 100 mm clearance above the top cover allow a minimum 50 mm clearance from the side vents do not place any heat source directly above the top cover or below the bottom cover b On a wall (DLP 122). 5 Review the connection locations as shown in Figure NTP 175-1, NTP and NTP for the I-120G-B or I-240G-D indoor ONTs. Figure NTP 175-1: I-120G-B indoor ONT connections (back view) OPTICAL TEL LAN 2 LAN 1 POWER ON/OFF Fiber optic port POTS port (RJ-11) Ethernet ports (RJ-45) Power connector On/off switch Figure NTP 175-2: I-240G-D indoor ONT connections (back view) OPTICAL TEL1 TEL2 LAN 4 LAN 3 LAN 2 LAN 1 POWER ON/OFF Fiber optic port POTS ports (RJ-11) Ethernet ports (RJ-45) Power connector On/off switch Figure NTP 175-3: I-120G-B and I-240G-D indoor ONT (side view) LED RESET LED button Reset button Connect the Ethernet cables to the RJ-45 ports (DLP 101). Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November 2013 NTP FE AAAA TCZZA Edition 01

141 NTP 175 Install an I-120G-B or I-240G-D indoor ONT 7 Connect the POTS cables to the RJ-11 ports (DLP 123). 8 Connect the SC/APC fiber optic cable (DLP 125). Warning Be careful to maintain a bend radius of no less than 1.5 inches (3.8 cm) when connecting the fiber optic cable. Too small of a bend radius in the cable can result in damage to the optic fiber. 9 Install the power supply according to manufacturer specifications. Note Observe the following: Units must be powered by a Listed or CE approved and marked limited power source power supply with a minimum output rate of 12 V dc, 1.25 A. 10 Connect the power cable to the power connector. 11 Power up the ONT unit by using the power switch. 12 Verify the ONT LEDs, voltage status, and optical signal levels (DLP 127). 13 Activate and test the services (DLP 128). 14 If used, configure the SLID (DLP 129). 15 If necessary, reset the ONT (DLP 126). 16 STOP. This procedure is complete. NTP November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

142 NTP 176 Replace an I-120G-B or I-240G-D indoor ONT Purpose This NTP provides the steps to replace I-120G-B or I-240G-D indoor ONTs. General The DLPs listed in this NTP describe mounting and cabling for I-120G-B and I-240G-D indoor ONTs. Prerequisites See the listed DLPs for prerequisites. Recommended tools You need the following tools for replacing the ONT: #2 Phillips screwdriver 1/4 in. (6 mm) flat blade screwdriver wire strippers fiber optic splicing tools RJ-45 cable plug crimp tool voltmeter or multimeter optical power meter drill and drill bits Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November 2013 NTP FE AAAA TCZZA Edition 01

143 NTP 176 Replace an I-120G-B or I-240G-D indoor ONT Safety information Read the following safety information before replacing the unit. Danger 1 Contact the local utility company before you connect the enclosure to the utilities. Danger 2 Observe the local and national laws and regulations that may be applicable to this installation. Warning This equipment is ESD sensitive. Proper ESD protections should be used when removing the fiber access cover of the indoor ONT. Caution Keep indoor ONTs out of direct sunlight. Prolonged exposure to direct sunlight can damage the unit. Procedure Note Observe the following: The indoor ONT should be installed in accordance with the applicable requirements of the NEC or CEC. Local authorities and practices take precedent when there is conflict between the local standard and the NEC or CEC. The indoor ONT must be installed by qualified service personnel. Indoor ONTs must be installed with cables that are suitably rated and listed for indoor use. See the detailed specifications in the I-120G-B and I-240G-D unit data sheet for the ONT temperature ranges for these ONTs. Use this procedure to replace an I-120G-B or I-240G-D indoor ONT. 1 Deactivate the ONT services (DLP 131). If you are using the SLID feature, this step is not required. The ONT and the services can remain in service (IS). 2 Power down the unit by using the on/off power switch. 3 Disconnect the POTS, Ethernet, and power cables (DLP 132) as well as fiber optic cables (DLP 133) from the ONT; see Figures NTP 176-1, NTP and NTP for the connector locations on the I-120G-B or I-240G-D indoor ONT. NTP November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

144 NTP 176 Replace an I-120G-B or I-240G-D indoor ONT Figure NTP 176-1: I-120G-B ONT connections (back view) OPTICAL TEL LAN 2 LAN 1 POWER ON/OFF Fiber optic port POTS port (RJ-11) Ethernet ports (RJ-45) Power connector On/off switch Figure NTP 176-2: I-240G-D ONT connections (back view) OPTICAL TEL1 TEL2 LAN 4 LAN 3 LAN 2 LAN 1 POWER ON/OFF Fiber optic port POTS ports (RJ-11) Ethernet ports (RJ-45) Power connector On/off switch Figure NTP 176-3: I-120G-B and I-240G-D ONT (side view) LED RESET LED button Reset button Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November 2013 NTP FE AAAA TCZZA Edition 01

145 NTP 176 Replace an I-120G-B or I-240G-D indoor ONT 4 Replace the ONT with a new unit: a On a flat surface, such as a desk. i Substitute the new ONT for the old ONT on a flat surface, horizontally resting on its four feet. Note The I-120G-B or I-240G-D cannot be stacked with another ONT or with other equipment. The ONT mounting requirements are: allow a minimum 100 mm clearance above the top cover allow a minimum 50 mm clearance from the side vents do not place any heat source directly above the top cover or below the bottom cover ii Go to step 5. b On a wall. i ii Slide the old ONT off of the mounting screws until the ONT is free of the wall. Slide the wall mount holes on the ONT enclosure over the mounting screws until it is securely seated. 5 Connect the Ethernet cables to the RJ-45 ports (DLP 101). 6 Connect the POTS cables to the RJ-11 ports (DLP 123). 7 If required, have approved service personnel who are trained to work with optic fiber clean the fiber optic connection. See DLP 134 for more information about fiber optic handling, inspection, and cleaning. Danger Fiber optic cables transmit invisible laser light. To avoid eye damage or blindness, never look directly into fibers, connectors, or adapters. 8 Connect the SC/APC fiber optic cable (DLP 125). Warning Be careful to maintain a bend radius of no less than 1.5 inches (3.8 cm) when connecting the fiber optic cable. Too small of a bend radius in the cable can result in damage to the optic fiber. 9 Install the power supply according to manufacturer specifications. Note Observe the following: Units must be powered by a Listed or CE approved and marked limited power source power supply with a minimum output rate of 12 V dc, 1.25 A. 10 Connect the power cable to the power connector. 11 Power up the unit by using the power switch. NTP November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

146 NTP 176 Replace an I-120G-B or I-240G-D indoor ONT 12 If used, configure the SLID (DLP 129). Note A new SLID or the old SLID may be used with the replacement ONT. If a new SLID is used, the new SLID must also be programmed at the P-OLT using TL1 or a network manager. If the old SLID is used, no changes need to be made at the P-OLT; see the operations and maintenance documentation for the OLT for more details. 13 Verify the ONT LEDs, voltage status, and optical signal levels (DLP 127). 14 Activate and test the services (DLP 128). 15 If necessary, reset the ONT (DLP 126). 16 STOP. This procedure is complete. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November 2013 NTP FE AAAA TCZZA Edition 01

147 NTP 176 Replace an I-120G-B or I-240G-D indoor ONT NTP November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

148 NTP 177 Configure an I-120G-B or I-240G-D indoor ONT General Please refer to the OLT Operations and Maintenance using TL1 and CLI guide for the software configuration procedure for I-120G-B and I-240G-D indoor ONTs. For HTTP configuration procedures, please refer to chapter 6, ONT management using an ONT interface. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November 2013 NTP FE AAAA TCZZA Edition 01

149 NTP 177 Configure an I-120G-B or I-240G-D indoor ONT NTP November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

150 I-240G-P, I-240G-Q, I-240G-T, I-241G-P, I-241G-R 34 I-240G-P, I-240G-Q, I-240G-T, I-241G-P, and I-241G-R unit data sheet NTP 178 Install an I-240G-P, I-24OG-Q, I-240G-T, I-241G-P, or I-241G-R indoor ONT NTP 179 Replace an I-240G-P, I-240G-Q, I-240G-T, I-241G-P, or I-241G-R indoor ONT NTP 180 Configure an I-240G-P, I-240G-Q, I-240G-T, I-241G-P, or I-241G-R indoor ONT Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

151 November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

152 34 I-240G-P, I-240G-Q, I-240G-T, I-241G-P, and I-241G-R unit data sheet 34.1 I-240G-P, I-240G-Q, I-240G-T, I-241G-P, and I-241G-R part numbers and identification I-240G-P, I-240G-Q, I-240G-T, I-241G-P, and I-241G-R general description I-240G-P, I-240G-Q, I-240G-T, I-241G-P, and I-241G-R software and installation feature support I-240G-P, I-240G-Q, I-240G-T, I-241G-P, and I-241G-R interfaces and interface capacity I-240G-P, I-240G-Q, I-240G-T, I-241G-P, and I-241G-R LEDs I-240G-P, I-240G-Q, I-240G-T, I-241G-P and I-241G-R detailed specifications I-240G-P, I-240G-Q, I-240G-T, I-241G-P and I-241G-R GEM ports and T-CONTs I-240G-P, I-240G-Q, I-240G-T, I-241G-P and I-241G-R power support I-240G-P, I-240G-Q, I-240G-T, I-241G-P, and I-241G-R functional blocks Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

153 34 I-240G-P, I-240G-Q, I-240G-T, I-241G-P, and I-241G-R unit data sheet I-240G-P, I-240G-Q, I-240G-T, I-241G-P and I-241G-R standards compliance I-240G-P, I-240G-Q, I-240G-T, I-241G-P, and I-241G-R special considerations November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

154 34 I-240G-P, I-240G-Q, I-240G-T, I-241G-P, and I-241G-R unit data sheet 34.1 I-240G-P, I-240G-Q, I-240G-T, I-241G-P, and I-241G-R part numbers and identification Table 34-1 provides part numbers and identification information for I-240G-P, I-240G-Q, I-240G-T, I-241G-P, and I-241G-R indoor ONTs. Table 34-1 I-240G-P, I-240G-Q, I-241G-P, and I-241G-R part numbers and identification Mnemonic Ordering kit part number Provisioning part number Description CLEI CPR ECI/ Bar code I-240G-P 3FE AC 3FE AD GPON I-series ONT, version P, 2 POTS and 4 GigE Ethernet interfaces. Includes ac/dc power cord with European variant plug. 3FE AN GPON I-series ONT, version P, 2 POTS, and 4 GigE Ethernet interfaces. Includes ac/dc power cord with Australian variant plug. 3FE AP GPON I-series ONT, version P, 2 POTS and 4 GigE Ethernet interfaces.includes ac/dc power cord with United Kingdom variant plug. 3FE AX (customerspecific variant) 3FE AE GPON I-series ONT, version P, 2 POTS and 4 GigE Ethernet interfaces.includes ac/dc power cord with United Kingdom variant plug. 3FE AA (customerspecific variant) 3FE AQ GPON I-series ONT, version P, 2 POTS and 4 GigE Ethernet interfaces.includes ac/dc power cord with United Kingdom variant plug. I-240G-Q 3FE AA 3FE AC GPON I-series ONT, version Q, 2 POTS and 4 GigE Ethernet interfaces.capable of being configured as a Residential Gateway (RGW). Includes ac/dc power cord with European variant plug. 3FE AB 3FE AC GPON I-series ONT, version Q, 2 POTS and 4 GigE Ethernet interfaces. Capable of being configured as a Residential Gateway (RGW). Includes ac/dc power cord with Australian variant plug. GPON I-series ONT, version P, 2 POTS and 4 GigE Ethernet interfaces. Capable of being configured as a Residential Gateway (RGW). Includes ac/dc power cord with United Kingdom variant plug. (1 of 2) Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

155 34 I-240G-P, I-240G-Q, I-240G-T, I-241G-P, and I-241G-R unit data sheet Mnemonic Ordering kit part number Provisioning part number Description CLEI CPR ECI/ Bar code I-240G-T 3FE AB 3FE AA GPON I-series ONT, version T, 2 POTS and 4 GigE Ethernet interfaces. Includes ac/dc power cord with European (EU) variant plug. 3FE AA (customerspecific variant) 3FE AB GPON I-series ONT, version T, 2 POTS and 4 GigE Ethernet interfaces. Includes ac/dc power cord with European (EU) variant plug. 3FE BA GPON I-series ONT, version T, 2 POTS and 4 GigE Ethernet interfaces. Includes ac/dc power cord with Australian (AU) variant plug. 3FE CA GPON I-series ONT, version T, 2 POTS and 4 GigE Ethernet interfaces. Includes ac/dc power cord with United Kingdom (UK) variant plug. 3FE EA GPON I-series ONT, version T, 2 POTS and 4 GigE Ethernet interfaces. Includes ac/dc power cord with United States (US) variant plug. I-241G-R 3FE AZ 3FE AT GPON I-series ONT, version R, 2 POTS, 4 GigE Ethernet, and 1 RF video interfaces. Includes ac/dc power cord with European variant plug. I-241G-P 3FE AD 3FE AM GPON I-series ONT, version P, 2 POTS, 4 GigE Ethernet, and 1 RF video interfaces.includes ac/dc power cord with European variant plug and fiber storage tray. 3FE AS 3FE AU GPON I-series ONT, version P, 2 POTS, 4 GigE Ethernet, and 1 RF video interfaces.includes ac/dc power cord with Australian variant plug and fiber storage tray. GPON I-series ONT, version P, 2 POTS, 4 GigE Ethernet, and 1 RF video interfaces.includes ac/dc power cord with United Kingdom variant plug and fiber storage tray. (2 of 2) 34.2 I-240G-P, I-240G-Q, I-240G-T, I-241G-P, and I-241G-R general description The I-240G-P, I-240G-Q, I-240G-T, I-241G-P, and I-241G-R indoor ONTs provide a subscriber interface for the network by terminating the PON interface and converting it to user interfaces that directly connect to subscriber devices. The ONT is compatible with all existing subscriber equipment, including analog phones with both tone and rotary dial capabilities, cordless phones, modems, fax machines, and caller ID boxes (Type I, Type II, and Type III) November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

156 34 I-240G-P, I-240G-Q, I-240G-T, I-241G-P, and I-241G-R unit data sheet These indoor ONTs provide the following functions: fully G.984 series GPON standard compliant G984.4 and G standard compliant ONT Management Control Interface (OMCI) interface for ONT management and provisioning Management Information Base (MIB) manipulation over OMCI by Create, Delete, Set, Get, and Get next commands optics that support received signal strength indication (RSSI) remote software image download (as well as activation and reboot) over OMCI performance monitoring as well as alarms and AVC reports The I-240G-P ONT provides the following additional functions: IGMP snooping delivers video content in the form of data by multicast or unicast support for Multicast GEM port The I-241G-P ONT provides the following additional functions: two types of video services: video overlay and IP Television/Video on Demand (IPTV/VoD) support for Multicast GEM port for IPTV services optional TR-069 Customer Premises Equipment (CPE) WAM management limited web-based end-user configuration 34.3 I-240G-P, I-240G-Q, I-240G-T, I-241G-P, and I-241G-R software and installation feature support Table 34-2 provides a list of software-based features and installation information supported by I-240G-P, I-240G-Q, I-240G-T, I-241G-P, and I-241G-R indoor ONTs. Table 34-2 I-240G-P, I-240G-Q, I-240G-T, I-241G-P, and I-241G-R indoor ONT software feature support Features Chapter Cross reference for more information General ONT and MDU overview Service interface specifications RSSI specifications General information common to multiple devices and an explanation of general system behaviors. ONT and MDU general and interface technical specifications ONT and MDU general and interface technical specifications ONT and MDU overview Ethernet interface specifications POTS interface specifications RF video interface specifications for video overlay (I-241G-P and I-241G-R ONTs only) RSSI specifications Wi-Fi specifications Optical budget (1 of 2) ONT and MDU general and interface technical specifications ONT optical budget Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

157 34 I-240G-P, I-240G-Q, I-240G-T, I-241G-P, and I-241G-R unit data sheet Features Chapter Cross reference for more information Location and installation options How to install and replace I-240G-P, I-240G-Q, I-240G-T, I-241G-P, or I-241G-R indoor ONTs Install an I-240G-P, I-24OG-Q, I-240G-T, I-241G-P, or I-241G-R indoor ONT Replace an I-240G-P, I-240G-Q, I-240G-T, I-241G-P, or I-241G-R indoor ONT Activation method ONT and MDU overview ONT activation and behavior using SLID HTTP ONT management procedures Statistics and performance monitoring Supported UPS (2 of 2) Information necessary to manage an ONT at a local site using an HTTP interface, CLI interface, CLI interface, or butt set. ONT and MDU statistics and performance monitoring Part numbers, ordering, and deployment configuration overview ONT management using an ONT interface Procedure using butt set or telephone for Package D ONTs Performance monitoring statistics for Package C ONTs Performance monitoring statistics for Package K ONTs (I-240G-T ONTs only) ONT and MDU to UPS or power adapter compatibility support 34.4 I-240G-P, I-240G-Q, I-240G-T, I-241G-P, and I-241G-R interfaces and interface capacity Table 34-3 describes the supported interfaces and the maximum connection capacity for I-240G-P, I-240G-Q, I-240G-T, I-241G-P, and I-241G-R indoor ONTs. Table 34-3 I-240G-P, I-240G-Q, I-240G-T, I-241G-P, and I-241G-R indoor ONT interface connection capacity ONT type and model Maximum capacity POTS 10/ 100 BASE-T 10/ 100/ 1000 BASE-T RF video (CATV) MoCA VDSL2 DS1/ E1 Local craft GPON SC/ APC I-240G-P I-240G-Q I-240G-T I-241G-P I-241G-R (1) 1 Note (1) The I-241G-R ONT is identical to the I-241G-P ONT except that the RF video has an additional RF filter. The I-240G-P, I-240G-Q, I-240G-T, I-241G-P, and I-241G-R indoor ONTs are for indoor deployment and can be installed horizontally on a flat surface as well as attached to a wall. The I-241G-P indoor ONT comes equipped with a removable fiber access tray for storing excess cable. Figure 34-1 shows the connections for I-240G-P and I-240G-Q indoor ONTs November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

158 34 I-240G-P, I-240G-Q, I-240G-T, I-241G-P, and I-241G-R unit data sheet Figure 34-1 I-240G-P and I-240G-Q indoor ONT physical connections POWER OPTICAL LAN UPDATE ALARM POTS GE1 GE2 GE3 GE4 POTS1 POTS2 RESET PWR Ethernet ports (RJ45) POTS ports (RJ-11) Fiber optic connector Power connector Reset button Figure 34-2 shows the I-240G-T indoor ONT physical connections. Figure 34-2 I-240G-T indoor ONT connections POWER OPTICAL LAN UPDATE ALARM POTS RESET PWR GE1 GE2 GE3 GE4 POTS1 POTS2 Ethernet ports (RJ45) Reset button ON/OFF POTS ports (RJ-11) Power ON/OFF button Power connector Fiber optic connector The I-240G-T indoor ONTs has an ON/OFF power button for manual shut down when needed. Figure 34-3 shows the connections for I-241G-P and I-241G-R indoor ONTs. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

159 34 I-240G-P, I-240G-Q, I-240G-T, I-241G-P, and I-241G-R unit data sheet Figure 34-3 I-241G-P and I-241G-R indoor ONT physical connections GE POTS Ethernet ports (RJ45) POTS ports (RJ-11) F-Type coaxial connector Power connector A B RF Fiber optic connector (internal) PWR 12VDC GPON 2.5G/1.25G G B+ Class 1 Laser Table 34-4 describes the physical connections on I-240G-P, I-240G-Q, I-240G-T, I-241G-P, and I-241G-R indoor ONTs. Table 34-4 I-240G-P, I-240G-Q, I-240G-T, I-241G-P, and I-241G-R indoor ONT physical connections Connection (1) Ethernet ports POTS RF video coaxial (I-241G-P and I-241G-R ONT only) Power Fiber optic Description This connection is provided through Ethernet RJ-45 cables. Up to four 10/100/1000 Base-T Ethernet interfaces are supported.the Ethernet ports can support both data and in-band video services on all four interfaces. This connection is provided through RJ-11 ports. Up to two POTS connections are supported.the POTS ports support voice services. This connection is provided through an F-Type coaxial connector. This connection is provided through the power connector. A power cable fitted with a barrel connector is used to make the connection. This connection is provided through a SC/APC fiber optic connector. The fiber optic connector is located behind a fiber optic port cover on these ONTs. Note (1) The primary path for the earth ground for these ONTs is provided by the 12V Return signal in the power connector I-240G-P, I-240G-Q, I-240G-T, I-241G-P, and I-241G-R LEDs Figure 34-4 shows the I-240G-P, I-240G-Q, and I-240G-T indoor ONT LEDs November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

160 OPTICAL LAN UPDATE ALARM POTS POWER 34 I-240G-P, I-240G-Q, I-240G-T, I-241G-P, and I-241G-R unit data sheet Figure 34-4 I-240G-P, I-240G-Q, and I-240G-T indoor ONT LEDs POWER OPTICAL LAN UPDATE ALARM POTS Table 34-5 provides I-240G-P and I-240G-T indoor ONT LED descriptions. Table 34-5 I-240G-P and I-240G-T indoor ONT LEDs Indicator LED color and behavior LED behavior description POWER OPTICAL LAN UPDATE ALARM (1) POTS Green solid Green flashing Red solid Green solid Green flashing Off Green solid Green flashing Off Green flashing Red solid Off Red solid Red flashing Green solid Off Green solid Green flashing Operating on ac power ONT is starting up Optical interface abnormal (LOS or LOF) ONT working normally ONT is ranging and synchronizing Ethernet service is not configured in the ONT Ethernet service is configured in the ONT Ethernet service is not configured in the ONT and there is transmitting or receiving activity No software update ONT software downloading ONT software download failed ONT is operating without failure ONT hardware is out of order ONT software failure No alarm, with local access enabled No POTS provisioned (all phones are on-hook or no phones connected) One or more phones are off-hook One or more phones are off-hook for the minimum of one hour I-240G-P indoor ONTs (3FE AX variant) (1 of 2) Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

161 34 I-240G-P, I-240G-Q, I-240G-T, I-241G-P, and I-241G-R unit data sheet Indicator LED color and behavior LED behavior description OPTICAL POTS (2 of 2) Red solid Red and green flashing Green solid Green flashing Off Green solid Green flashing No optical signal detected Not registered to the OLT Register to the OLT Ranging POTS port not registered or not configured POTS port registered to IMS/SIP server One or more phones are off-hook Note (1) For the I-240G-T 3FE AB variant only, the solid green LED means that the ONT is operating without failure. Table 34-6 provides I-240G-Q indoor ONT LED descriptions. Table 34-6 I-240G-Q indoor ONT LEDs Indicator LED color and behavior LED behavior description POWER OPTICAL LAN UPDATE ALARM POTS Off Red solid Green solid Green flashing (slow) Green flashing (fast) Off Red solid Green solid Green flashing Off Green solid Green flashing Off Red solid Green flashing Off Red solid Green solid Off Green solid Green flashing No power Battery power is low Operating on ac power Operating on battery power ONT is starting up Optical power is off ONT initial ranging is complete PON is engaged in ranging and synchronizing process WAN is not configured Successful PPPoE/DHCP signup. Internet is connected. L2 path is complete and PPPoE/DHCP signup is underway Normal status ONT software download failed ONT software downloading Normal status ONT hardware failure No alarm, with local Ethernet access enabled No POTS provisioned (all phones are on-hook or no phones connected) One or more phones are off-hook One or more phones are off-hook for the minimum of one hour Figure 34-5 shows the I-241G-P and I-241G-R indoor ONT LEDs November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

162 RESET 34 I-240G-P, I-240G-Q, I-240G-T, I-241G-P, and I-241G-R unit data sheet Figure 34-5 I-241G-P and I-241G-R indoor ONT LEDs PWR GPON INET UPG ALARM POTS VIDEO Table 34-7 provides I-241G-P and I-241G-R indoor ONT LED descriptions. Table 34-7 I-241G-P and I-241G-R indoor ONT LED descriptions Indicator LED color and behavior LED behavior description PWR GPON INET UPG (1 of 2) Off Green solid Green flashing Red solid (I-241G-P and I-241G-R only) Red solid Green solid Green flashing Off Green solid Green flashing Off Green solid (I-241G-P only) Green flashing Red solid No power Operating on ac power ONT is starting up Operating on battery backup power Equipment failure or not ranged or synchronized ONT initial ranging is complete ONT management control interface (OMCI) traffic exchange between OLT and ONT None of the data ports are connected Some of the data In/Out devices/ports are connected Some of the data In/Out devices/ports are active and passing traffic. Faster flashes indicate faster traffic rates. No software update ONT software download complete ONT software downloading ONT software download failed Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

163 34 I-240G-P, I-240G-Q, I-240G-T, I-241G-P, and I-241G-R unit data sheet Indicator LED color and behavior LED behavior description ALARM POTS or OFFHOOK (I-241G-P) VIDEO (2 of 2) Off Red solid Red flashing Off Green solid Off Green ONT is operating without failure ONT hardware is out of order ONT software failure No POTS provisioned (all phones are on-hook or no phones connected) One or more phones are off-hook RF is disabled or the video optical band being received is lower than the prescribed limit RF is enabled and optical signal power is working 34.6 I-240G-P, I-240G-Q, I-240G-T, I-241G-P and I-241G-R detailed specifications Table 34-8 lists the physical specifications for I-240G-P and I-240G-Q indoor ONTs. Table 34-8 I-240G-P, I-240G-Q, and I-240G-T indoor ONT physical specifications Dimensions Height Width Depth Specifications 5.1 in. (13 cm) 6.8 in. (17.2 cm) 1.3 in. (3.3 cm) Weight [within ± 0.5 lb (0.23 kg)] 1.1 lb (500 g) Table 34-9 lists the physical specifications for I-241G-P and I-241G-R indoor ONTs. Table 34-9 I-241G-P and I-241G-R indoor ONT physical specifications Dimensions Height Width Depth Specifications 2.6 in. (6.6 cm) 10.5 in. (26.7 cm) 7.9 in. (20 cm) Weight [within ± 0.5 lb (0.23 kg)] 2.2 lb (990 g) Table lists power consumption specifications for I-240G-P, I-240G-Q, I-241G-P, and I-241G-R indoor ONTs November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

164 34 I-240G-P, I-240G-Q, I-240G-T, I-241G-P, and I-241G-R unit data sheet Table I-240G-P, I-240G-Q, I-240G-T, I-241G-P and I-241G-R indoor ONT power consumption specifications Mnemonic Maximum power (not to exceed) Condition Minimum power Condition I-240G-P and I-240G-Q 9 W 2 POTS off-hook, 4 Gig-E operational 4.5 W 2 POTS on-hook, other interfaces/services not provisioned I-240G-T 8.2 W 2 POTS off-hook, 4 E operational 5 W 2 POTS on-hook, other interfaces/services not provisioned I-241G-P and I-241G-R 12 W 2 POTS off-hook, 4 Gig-E, Video operational 5.5 W 2 POTS on-hook, other interfaces/services not provisioned Table lists the environmental requirements for I-240G-P, I-240G-Q, I-240G-T, I-241G-P and I-241G-R indoor ONTs. Table I-240G-P, I-240G-Q, I-240G-T, I-241G-P and I-241G-R indoor ONT environmental requirements ONT type Mounting method Temperature range and humidity Altitude Desk or wall mounted Operating: 32 F to 104 F (0 C to 40 C) ambient temperature 5% to 90% relative humidity, non-condensing Storage: Contact your Alcatel-Lucent support representative for more information Contact your Alcatel-Lucent technical support representative for more information 34.7 I-240G-P, I-240G-Q, I-240G-T, I-241G-P and I-241G-R GEM ports and T-CONTs Table lists the maximum number of supported T-CONTs and GEM ports for I-240G-P, I-240G-Q, I-240G-T, I-241G-P, and I-241G-R indoor ONTs. Not all ONTs will be supported in all of the releases indicated the table. See the appropriate release Customer Release Notes for the most accurate list of supported devices. Table I-240G-P, I-240G-Q, I-240G-T, I-241G-P and I-241G-R indoor ONT capacity for GEM ports and T-CONTs per package and release ONT or MDU Release (1) Maximum Notes Package C ONTs (1 of 2) Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

165 34 I-240G-P, I-240G-Q, I-240G-T, I-241G-P, and I-241G-R unit data sheet ONT or MDU Release (1) Maximum Notes GEM ports per indoor or outdoor ONT R to R are present: 10 are available, 2 are reserved for multicast and debugging R x, R , R , R R x, R x, R x, R x, R x are present: 30 are available, 2 are reserved for multicast and debugging 30 R x 30 T-CONTs per indoor or outdoor ONT R to R are present: 6 are available, 1 is reserved for OMCI R x, R , R , R R x, R x, R x, R x, R x, R x R x, R x, R x, R are present: 15 are available, 1 is reserved for OMCI are present: 31 are available, 1 is reserved for OMCI Package K ONTs (I-240G-T ONT only) GEM ports per ONT All 32 per UNI 128 are present: 126 are available, 2 are reserved for multicast and debugging T-CONTs per ONT All are present: 15 are available, 1 is reserved for OMCI (2 of 2) Note (1) The letter x following a release number denotes either a letter of the alphabet for maintenance releases or digit from 0 to 9 for minor releases I-240G-P, I-240G-Q, I-240G-T, I-241G-P and I-241G-R power support The following power supply supports the I-240G-P, I-240G-Q, I-240G-T, I-241G-P and I-241G-R indoor ONTs. Click on one of the links for more information. Leader Electronics 12W, 18W, and 24W ac/dc switching power supply unit data sheet Leader Electronics 12W, 18W, and 24W ac/dc switching power supply unit data sheet (3FE AA variant of the I-240G-P ONT only) DVE 12 W AC/DC switching power adapter unit data sheet (I-240G-T ONT only) 34.9 I-240G-P, I-240G-Q, I-240G-T, I-241G-P, and I-241G-R functional blocks This chapter describes the new and highly integrated System on a Chip (SoC) technology used on I-240G-P, I-240G-Q, I-240G-T, I-241G-P, and I-241G-R indoor ONTs November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

166 34 I-240G-P, I-240G-Q, I-240G-T, I-241G-P, and I-241G-R unit data sheet I-240G-P, I-240G-Q, I-241G-P, and I-241G-R functional blocks Table describes the supported interfaces for I-240G-P, I-240G-Q, I-241G-P, and I-241G-R ONTs (Package C). Table I-240G-P, I-240G-Q, I-241G-P, and I-241G-R ONT interfaces ONT category description Interface capacity POTS ports Ethernet ports VDSL2 MoCA RF Video HPNA Wi-Fi Single-residence Gigabit Ethernet ONTs with POTS and with or without RF video Optional 0 0 I-240G-P, I-240G-Q, I-241G-P, and I-241G-R indoor ONTs transmit Ethernet packets to four RJ-45 Ethernet ports and voice traffic to two RJ-11 POTS ports. RF video ports are available for I-241G-P and I-241G-R ONTs in addition to POTS and Ethernet ports and transmit video traffic to one F-type coaxial connector.these ONTs also feature fiber optic and power connectors. Figure 34-6 shows the functional blocks for I-240G-P and I-240G-Q indoor ONTs with Gigabit Ethernet, POTS, and coaxial ports. For those ONTs with less than the maximum number of Gigabit Ethernet or POTS ports, the excess ports are blocked by a plastic cover. Figure 34-6 Single-residence Gigabit Ethernet ONT with POTS and with or without RF video (diplexer) Power Converter Power connector GPON Optical block SOC POTS (4/2/1) Ethernet (4/2) RJ-11 RJ-45 RF Video Amp Diplexer F-type connector Figure 34-7 shows the functional blocks for I-241G-P and I-241G-R ONTs with four Gigabit Ethernet, two POTS, and coaxial ports. This ONT has a triplexer and RF filter rather than a diplexer. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

167 34 I-240G-P, I-240G-Q, I-240G-T, I-241G-P, and I-241G-R unit data sheet Figure 34-7 Single-residence Gigabit Ethernet ONT with POTS and RF video (triplexer) Power Converter Power connector GPON SOC POTS (2) GigE (4) RJ-11 RJ-45 Triplexer RF Filter F-type connector The hardware blocks for I-240G-P, I-240G-Q, I-241G-P, and I-241G-R indoor ONTs are described in ONT SoC technology. I-240G-T functional blocks Table describes the supported interfaces for I-240G-T indoor ONTs (Package K). Table I-240G-T indoor ONT interfaces ONT category description Interface capacity POTS ports Ethernet ports VDSL2 MoCA RF Video HPNA Wi-Fi Single-residence Gigabit Ethernet ONTs with POTS and without RF video The hardware blocks for I-240G-T indoor ONTs are described in ONT SoC technology. ONT SoC technology ONT SoC technology serves as the main hardware block for I-240G-P, I-240G-Q, I-240G-T, I-241G-P, and I-241G-R indoor ONTs; see Figure November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

168 34 I-240G-P, I-240G-Q, I-240G-T, I-241G-P, and I-241G-R unit data sheet Figure 34-8 I-240G-P, I-240G-Q, I-240G-T, I-241G-P and I-241G-R ONT hardware block POTS ports Control processor SoC DSP SoC Bridge Ethernet MACs GPON MAC Ethernet ports GPON ONT SoC technology consists of five key elements: GPON MAC The Gigabit Passive Optical Network Media Access Control (GPON MAC) element on the SoC terminates the GPON interface using an optical diplexer. This interface supports GPON as described in G (GPON TC Layer) ITU specification. Ethernet MAC The SoC provides up to four GE MACs. DSP interface The Digital Signal Processor (DSP) provides voice processing for 2 POTS lines with the 3-way calling. The DSP has a dedicated 64 kbyte instruction cache and shares a 32 kbyte data cache with the Control Processor. Control Processor The Control Processor features an integral memory management unit that supports a dedicated 64 kbyte instruction cache and shares a single 32 kbyte data cache with the DSP. The Control Processor and DSP also include a single channel Data Management Application (DMA) controller with a 4 kbyte read ahead low-latency Dynamic Random Access Memory (DRAM) access port. The processors typically run at 400 MHz. Switch matrix The Switch matrix provides an integrated data channel between the four GE MACs, the GPON MAC, the MoCA MAC, the DSP, the control processor, and the other integrated elements such as flash memory, DRAM, and the local bus controller. These ONTs can also interact with additional hardware components to support functionality not provided by the SoC technology. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

169 34 I-240G-P, I-240G-Q, I-240G-T, I-241G-P, and I-241G-R unit data sheet I-240G-P, I-240G-Q, I-240G-T, I-241G-P and I-241G-R standards compliance The I-240G-P, I-240G-Q, I-240G-T, I-241G-P, and I-241G-R indoor ONTs are compliant with the following standards: 802.1d support for bridging 802.1p support for mapping and mapper service profile on U/S 802.1p support for marking and remarking 802.1p support for Class of Service based on VLAN-ID 802.1q support for virtual switch based on VLAN G.711 support for FAX, modem connection, and TTY devices G.984 support GPON interface (framing) G support for Amd1, Class B+ G support for activation and password functions G support for AES with operator enable/disable on per port-id level G support for FEC in both upstream and downstream directions G support for multicast using a single GEM Port-ID for all video traffic G984.4 and G support for OMCI interface for ONT management and provisioning G support for blocking filter as an option I-240G-P, I-240G-Q, I-240G-T, I-241G-P, and I-241G-R special considerations Some I-240G-P indoor ONTs (3FE AX variant) support consultative call transfer with third party control. Service creation considerations and limitations Port-to-port mode must be enabled when using the four-port Ethernet I-240G-P, I-240G-Q, I-241G-P, and I-241G-R indoor ONTs. When using port-to-port mode, you can only configure one Ethernet port. Upgrade considerations and limitations Existing ONTs that use 7342 ISAM FTTU releases older than R04.06.xx and R04.07.xx must be upgraded to use R software while assigned to a PON ID value smaller than 64. For this purpose, if split ratios larger than 1:64 are being deployed, you may choose to set aside the first PON ID as a staging point. I-240G-P, I-240G-Q, I-241G-P, and I-241G-R ONT considerations and limitations Table lists the considerations and limitations for these ONTs November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

170 34 I-240G-P, I-240G-Q, I-240G-T, I-241G-P, and I-241G-R unit data sheet Table I-240G-P, I-240G-Q, I-240G-T, I-241G-P, and I-241G-R ONT considerations and limitations Considerations and limitations Support for up to 32 GEM ports per Ethernet UNI Support for 7 T-CONTs including the OMCI T-CONT Ethernet OAM (802.1 ag) is not supported TPID overwrite is not supported Anti-spoofing is supported on I-020G-P and I-120G-P ONTs by treating PPPoE packets in the same manner as IPoE packets when anti-spoofing is configured. Other ONTs do not support anti-spoofing x is not supported IGMPv3 snooping with SSM is not supported VLAN translation is supported prior to replication for downstream IPTV multicast. The same VLAN operation must be provisioned for all Ethernet UNIs participating in IPTV multicasting. The ONT will not support sending some untagged multicast frames through one Ethernet UNI while sending other tagged multicast frames through another Ethernet UNI. Double-tagged frames are not supported Flow control is not supported. The ONT will not generate PAUSE frames for the client if there is traffic congestion. Configurable Ethernet for VLAN tag detection is not supported. Currently, only 0x8100 is supported. POTS pull-break-dial-tone (PBDT) is not supported for SIP, H.248, and G6 Call history data collection (ONTCALLHST) is not supported G.729 and G.711 a/u are supported while G codec is not supported Only one global DSCP to pbit mapping table is supported Default Ethernet flow and wildcard Ethernet flow coexisting on the same Ethernet port is not supported Maximum of 16 service flows (VLANs) can be enabled with pbit translation Non-supported call services: Direct connect Warm line Call forward status indications Home Intercom Call park Bridged line Call pickup with barge-in Suppressed ringing Service classification by Ethertype is not supported The first time an ONT is connected, the initial Ethernet UNI is enabled by default. This Ethernet UNI can be disabled by the OLT. When pbit translation is enabled, each GEM port can only translate into one pbit. Mapping downstream Pbits to different GEM ports is the only form of supported pbit translation. Static multicast is not supported IPTV multicast over PPPoE (from the multicast port) is not supported PM counter is partially supported (1 of 2) Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

171 34 I-240G-P, I-240G-Q, I-240G-T, I-241G-P, and I-241G-R unit data sheet Considerations and limitations Pbit translation following DSCP to pbit mapping is not supported Pbit translation when a UNI is set to pass through any VLAN ID (unisidevlan=4096 and networksidevlan=4096) is not supported Packet loss occurs in 1G wirespeed. Due to the additional 4-byte routing tag, throughput is less than 1G for all packet lengths. Weighted round robin (WRR) is not accurate when configured with OMCI because the weight definition in the device is the reverse of OMCI definition For WRR scheduling, bandwidth not used by a queue can not be claimed by any other queues Up to eight extended VLAN rules per VLAN port is supported AES key can not be changed locally on an ONT 100M half is not supported (2 of 2) I-240G-T ONT considerations and limitations Table lists the considerations and limitations for this ONT. Table I-240G-T ONT considerations and limitations Considerations and limitations Support for up to 32 GEM ports per Ethernet UNI (128 in total) Support for 16 T-CONTs including the OMCI T-CONT ONT only supports enabling or disabling the ONTSIG (channel package) by setting the ME for the first UNI. ONT snoops IGMP in all provisioned VLAN ports. ONT ignores "Max simultaneous groups" and "multicastbandwidth" in "Multicast Service package table". ONT only supports IGMPv3 ASM. SSM is not supported. ONT should be rebooted to switch from channel package mode to ONT snooping mode. In channel package mode, the ONT only supports group aging time less than 80 seconds. ONT always ignores "double-tag rules" and only classifies packets based on the most outer VLAN tag. ONT always identifies VLAN tag by TPID 0x8100 and does not support TPID re-writing. The VID classified rule and PBIT classified rule should not co-exist on the UNI port, for example, a rule with VID 100 (all PBITs) and a rule with PBIT 1 (all VIDs). The VID classified rule and VID+PBIT classified rule may co-exist on the UNI port, but the VID should be unique. For example a rule of VID 100 and a rule VID PBIT 3 cannot be supported on the same UNI. (1 of 3) November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

172 34 I-240G-P, I-240G-Q, I-240G-T, I-241G-P, and I-241G-R unit data sheet Considerations and limitations VLAN Op limitations for non-broadcast packets received from incidental broadcast GEM (in G-38T and 7318). If non-broadcast packets, including multicast packets are received from incidental GEM port, they will be forwarded by hardware without rate limits. But the VLAN operation is limited, since the SoC only supports VLAN operation before packet replication. For each ANI side VLAN ID, the ONT supports a single UNI VLAN tag for all UNI ports. If the UNI egress VLAN is configured differently amongst UNI ports and the packet is duplicated to multiple UNI ports, the ONT will perform VLAN operation in an undefined way. This limitation is also applicable for IPv6 multicast traffic in some releases in which IPv6 multicast traffic is carried in incidental broadcast GEM. ONT cannot map "VID+all_priority" and "VID+specific_priority" flows after VLAN Op with same VID into the same GEM. ONT not supporting asymmetrical traffic class provisioning when enabling PBIT translation and 802.1p mapper. ONT CFM limitations: Due to CPU forwarding capability, the maximum CFM throughput support by the ONT is 200 pps. The resolution of timestamp in DM is in ms. Except for LBM/LTM/DMM/LMM, all other OAM messages will be regarded as Other. ONT software doesn't support 802.1x. ONTs don't support IEEE 802 LLC/SNAP frame format. Only Ethernet encapsulation frame format is supported. ONT cannot support filtering on packet p-bit in downstream direction. DHCP discovery packets (with source IP ) may be blocked in MAC+IP anti-spoofing mode. ONT can only support 7 anti-spoofing entries per UNI in IP-only inclusive mode. IPv6 packets are blocked in IP-only and MAC+IP inclusive anti-spoofing mode. ONT doesn't support per service IP anti-spoofing. Never provision a single MAC address in multiple anti-spoofing lists for different UNI ports. ONT does not support all-zero IP or MAC address in MAC+IP exclusive mode anti-spoofing. ONT doesn't support RTP performance monitoring. G codec is not supported. G.729 and G.711 a/u are supported. ONT does not support automatic fill-in of selected parameters based on keywords for those parameters in the SIP provisioning data. ONT does not support configuration of SIP timers used for signaling requests with these SIP provisioning parameters for each POTS line. ONT does not support RFC SDP Simple Capability Declaration. ONT does not support registrar and outbound proxy redundancy based on DNS A records or SRV Records. Tightly coupled call flow is not supported. POTS PBDT (Pull-Break-Dial-Tone) is not supported. Call History Data collection (ONTCALLHST) is not supported. (2 of 3) Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

173 34 I-240G-P, I-240G-Q, I-240G-T, I-241G-P, and I-241G-R unit data sheet Considerations and limitations The following call services are not supported: Direct Connect Call Forwarding Status indications Home Intercom Call Park Bridged Line Call Pickup with Barge-in Suppressed ringing Re-register POTS service when any one POTS port is reconfigured. ONT does not support the following whole ONT TC-layer transmit and receiving counters: received fragments received blocks transmitted fragments transmitted blocks ONT does not support some per GEM PM counters listed in OMCI. The ONT does not support the following PM counters: Loss GEM Fragment Counter Downstream Loss GEM Fragment Counter Upstream Bad GEM Headers Received Counter (3 of 3) Residential gateway rules and requirements I-240G-Q indoor ONTs support the configuration of the home network to act as a router that allows each device in the network to communicate with any other device. The following functions can be configured on these router ONTs: DHCP service IP routing and NAT function on the ONT DNS requirements IGMP functionality UPnP Note Do not configure the I-240G-Q indoor ONT as a router for the home network by using a bridge concept for all the devices in the home November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

174 34 I-240G-P, I-240G-Q, I-240G-T, I-241G-P, and I-241G-R unit data sheet DHCP service The DHCP allows individual clients to obtain IP configuration from a server at start-up. The DHCP can function in one of the following two ways: DHCP server for the LAN An internal DHCP server allocates IP addresses to all the network devices attached to the ONT. DHCP client instances on the WAN The ONT receives an IP addresses for each type of client instance from 23 different DHCP servers in the WAN network: one DHCP client instance for obtaining a public IP address for HSI data traffic one DHCP client instance for VoIP for obtaining a private IP address from the WAN network for voice (dedicated VLAN) Figure 34-9 shows a diagram of the LAN (DHCP server) and WAN (DHCP client) functioning of the DCHP service on an ONT. Figure 34-9 LAN and WAN functions of the DCHP service VoIP ONT STBx IPTV STBx PC Others DHCP server DHCP client for HSI data DHCP client for VoIP voice Devices connected to ONT IP addresses from DHCP server IP routing IP routing allows the network to be routed so that all devices in the home can communicate with each other. In this case, IP routing uses NAT for translation of the IP address of a host in a packet. NAT is employed by I-240G-Q indoor ONTs configured as a residential gateway to route traffic in one of the following two ways: HSI traffic is directed to a public IP address The default gateway that will route the HSI traffic has its address transmitted to the ONT router using DHCP Option 3. Video traffic is directed to a private IP address Routes used for the IPTV service are transmitted to the ONT router using DHCP Option 121. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

175 34 I-240G-P, I-240G-Q, I-240G-T, I-241G-P, and I-241G-R unit data sheet NAT rules are not used for VoIP traffic since the routes used by this traffic are received by DHCP Option 121. DNS requirements DNS maps a domain name to its corresponding IP address and vice versa. For the WAN, the ONT receives two series of DNS addresses: The first series of received DNS addresses are the primary and secondary addresses from the IP edge for HSI traffic. The second series of received DNS addresses are the primary and secondary addresses from the IP edge for video services. All four of these addresses are transmitted using DHCP Option 6. IGMP functionality IGMP is a network-layer protocol used to establish membership in a multicast group and not to carry user data. When enabled on these ONTs, IGMP possesses fast-leave capabilities as well as proxy and snooping functions. Also, the IGMP engine on the ONT features explicit host-tracking of IGMP requests. If two set-top boxes are seeking to access the same MCST channel, and one of them is leaving the channel, then the router will keep the channel available for the other set-top box. UPnP UPnP is a distributed open networking standard that uses TCP/IP for simple peer-to-peer network connectivity between devices. A UPnP device can dynamically join a network, obtain an IP address, convey its capabilities, and learn about other devices on the network. Also, a UPnP device can leave a network smoothly and automatically when it is no longer in use. Since the I-240G-Q indoor ONT can act as a router for networks with multiple devices, they have UPnP for their WAN traffic. Web-based ONT configuration and reporting The I-240G-Q indoor ONT supports limited configuration using a web-based GUI. The following configuring and reporting procedures can be performed using the GUI: network advanced maintenance status Procedure 34-1 Login to web-based GUI 1 Open a web browser and enter the IP address of the ONT in the address bar. The login window appears November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

176 34 I-240G-P, I-240G-Q, I-240G-T, I-241G-P, and I-241G-R unit data sheet The default gateway IP address is You can also obtain the IP address using DHCP after connecting your PC to the layer 3 UNI. 2 Enter your username and password in the Login window. The default username is root while the default password is admin. Note If you forget the current username and password, press the reset button for 5 s and the default values for the username and password will be recovered upon start up. 3 Click OK. 4 STOP. This procedure is complete. Network configuration using the web-based GUI The following procedures provide the steps for configuring the network settings for the LAN and WAN service. Procedure 34-2 Network LAN configuration 1 Select the LAN option from the Network section of the navigation tree in the GPON ONT window. The LAN window appears; see Figure Figure LAN window Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

177 34 I-240G-P, I-240G-Q, I-240G-T, I-241G-P, and I-241G-R unit data sheet 2 Configure the LAN parameters. Table describes the fields in the LAN window. Table LAN parameters Field MAC Address Local IP Address Subnet mask DHCP server Starting Ip Address Max Number of DHCP Users Client Lease Time IP Address Range Option60 Class ID1 Starting Ip Address Max Number of Option60 Users Option60 Class ID2 Starting Ip Address Max Number of Option60 Users Description MAC address of the LAN interface IP address of the LAN interface in dotted-decimal format. For example, a sample IP address is Subnet mask of the IP addresses in your LAN. The default is Select either the Enable or Disable radio button. If enabled, the ONT assigns IP addresses, an IP default gateway, and DNS servers to computers that support the DHCP client; for example, Windows 95, Windows NT. Starting IP address of the DHCP IP pool Maximum number of DHCP users Number of minutes of client lease time. A zero means one day of lease time IP address of the LAN interface in dotted-decimal format. For example, a range of IP addresses that could be entered is from to IP address for the PC that transits the DHCP discovery packets with the matched Option 60 value IP address of the PC that transits the DHCP discovery packets with the matched Option 60 value Maximum number of Option60 users IP address for the PC that transits the DHCP discovery packets with the matched Option 60 value IP address of the PC that transits the DHCP discovery packets with the matched Option 60 value Maximum number of Option60 users 3 Click Apply to save your changes or Refresh to clear the fields. Note By default, the LAN DHCP server is enabled. If the PC cannot get the IP address using DHCP, click Reset on the PC for 5 s and the default values for the LAN DHCP server will be recovered upon start up. 4 STOP. This procedure is complete November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

178 34 I-240G-P, I-240G-Q, I-240G-T, I-241G-P, and I-241G-R unit data sheet Procedure 34-3 Network WAN configuration 1 Select the WAN option from the Network section of the navigation tree in the GPON ONT window. The WAN window appears. 2 Select one of the following options to obtain the WAN IP address from the Internet Connection Type drop-down menu. i PPPoE The WAN window appears with the PPPoE tab displayed; see Figure Figure PPPoE tab of the WAN window Configure the PPPoE parameters. Table describes the PPPoE fields in the WAN window. Table PPPoE parameters Field Connection Status IP Address Subnet mask Default Gateway DNS Server 1 Description Status is either Connected or Disconnected IP address of the WAN interface Subnet mask of the WAN interface IP address of the node on the network that is chosen as default when the IP address does not match any other routes in the routing table IP Address of the first DNS server (1 of 2) Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

179 34 I-240G-P, I-240G-Q, I-240G-T, I-241G-P, and I-241G-R unit data sheet Field DNS Server 2 User Name Password Connection Mode Redial Period Description IP Address of the second DNS server Username for the PPPoE connection Password for the PPPoE connection Default mode is Keep Alive, which means the connection is always kept. The Manual option can also be selected from the drop-down menu Number of seconds, between 5 and 25, for the redial period (2 of 2) ii Automatic Configuration - DHCP The WAN window appears with the Automatic Configuration - DHCP tab displayed; see Figure Figure Automatic Configuration - DHCP tab of the WAN window Configure the DHCP parameters. You can connect or disconnect any DHCP connection by using the Disconnect and Connect buttons. Table describes the DHCP fields in the WAN window November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

180 34 I-240G-P, I-240G-Q, I-240G-T, I-241G-P, and I-241G-R unit data sheet Table DHCP parameters Field Connection Status MAC Address IP Address Subnet Mask Default Gateway DNS Server 1 DNS Server 2 Description Status is either Connected or Disconnected MAC address of the WAN interface IP address of the WAN interface Subnet mask of the IP addresses in your WAN. The default is IP address of the node on the network that is chosen as default when the IP address does not match any other routes in the routing table IP address of the first DNS server IP address of the second DNS server iii Static IP The WAN window appears with the Static IP tab displayed; see Figure Figure Static IP tab of WAN window Configure the Static IP parameters. Table describes the Static IP fields in the WAN window. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

181 34 I-240G-P, I-240G-Q, I-240G-T, I-241G-P, and I-241G-R unit data sheet Table Static IP parameters Field IP Address Subnet Mask Default Gateway DNS Server 1 DNS Server 2 Description IP address of the WAN interface Subnet mask of the IP addresses in your WAN. The default is IP address of the node on the network that is chosen as default when the IP address does not match any other routes in the routing table IP address of the first DNS server IP address of the second DNS server 3 Click Apply to save your changes or Refresh to clear the fields. 4 STOP. This procedure is complete. Advanced configuration using the web-based GUI The following procedures provide the steps for performing advanced ONT configuration including the setting up of SNTP, DDNS, port forwarding, and firewalls. Procedure 34-4 Advanced configuration 1 Select one of the following options from the Advanced section of the navigation tree in the GPON ONT window. i SNTP The SNTP window appears; see Figure November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

182 34 I-240G-P, I-240G-Q, I-240G-T, I-241G-P, and I-241G-R unit data sheet Figure SNTP window Configure the SNTP parameters. Go to step 2 when you are finished configuring the parameters. Table describes the fields in the SNTP window. Table SNTP parameters Field SNTP State NTP Time Server Time Zone Description Select either the Enable or Disable radio button Select an option from the drop-down menu or enter the IP address or URL of another network time protocol server Select a time zone from the drop-down menu ii DDNS The DDNS window appears; see Figure Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

183 34 I-240G-P, I-240G-Q, I-240G-T, I-241G-P, and I-241G-R unit data sheet Figure DDNS window Configure the DDNS parameters. Go to step 3 when you are finished configuring the parameters. Table describes the fields in the DDNS window. Table DDNS parameters Field DDNS Service User name Password Host Name Description Select a supported DDNS service or select Disable to turn off DDNS. Supported DDNS services are DynDNS.org and TZO.com. Username for your DDNS account Password for your DDNS account Host name iii Port Forwarding The Port Forwarding window appears; see Figure November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

184 34 I-240G-P, I-240G-Q, I-240G-T, I-241G-P, and I-241G-R unit data sheet Figure Port Forwarding window Configure the Port Forwarding parameters. Go to step 3 when you are finished configuring the parameters. Table describes the fields in the Port Forwarding window. Table Port Forwarding parameters Column Application Start-End Port Protocol To IP Address Start-End Port Enable Description Name of the application to be filtered. Options are: IFIP HTTP FTP Telnet Starting port number followed by the ending port number of the external host, in two fields Protocol(s) used by the application. Options are: TCP UDP Both IP address of the host that is currently blocked from the application Starting port number followed by the ending port number of the internal host, in two fields Check box to Enable to apply this filter rule; leave box unchecked to Disable this filter rule iv Firewall The Firewall window appears; see Figure Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

185 34 I-240G-P, I-240G-Q, I-240G-T, I-241G-P, and I-241G-R unit data sheet Figure Firewall window Configure the Firewall parameters. Go to step 3 when you are finished configuring parameters. Table describes the fields in the Firewall window. Table Firewall parameters Field Web Access from LAN Web Access from WAN Dmz Dmz Host UPnP Enable Description Select Enable to enable web access from the LAN or select Disable to disable web access from the LAN Select Enable to enable web access from the WAN, or select Disable to disable web access from the WAN Select Enable to turn on the demilitarized zone function, or select Disable to turn off the demilitarized zone function Select the first radio button and choose a preexisting (or preset) LAN host, or select the second radio button and enter an IP address manually Select Enable to enable the UPnP function, or select Disable to disable the UPnP function 2 Click Submit to save your SNTP configuration changes, then go to step 4. 3 Click Apply to save your changes or Refresh to clear the fields. 4 STOP. This procedure is complete November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

186 34 I-240G-P, I-240G-Q, I-240G-T, I-241G-P, and I-241G-R unit data sheet Maintenance configuration using the web-based GUI The following procedures provide the steps for performing maintenance tasks on the ONT. Procedure 34-5 Maintenance configuration 1 Select one of the following options from the Maintain section of the navigation tree in the GPON ONT window. i Password The Password window appears; see Figure Figure Password window Change your password by using this window, then go to step 2. Table describes the fields in the Password window. Table Password window fields Field Web New Password Re-enter to confirm Description New password other than the default one Confirm the new password by re-entering it ii Factory Default The Factory Default window appears; see Figure Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

187 34 I-240G-P, I-240G-Q, I-240G-T, I-241G-P, and I-241G-R unit data sheet Figure Factory Default window Click Reset to reset the system configuration to the factory default setting, then go to step 3. iii Reboot Device The Reboot Device window appears; see Figure Figure Reboot Device window November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

188 34 I-240G-P, I-240G-Q, I-240G-T, I-241G-P, and I-241G-R unit data sheet Click Reboot to reboot the system, the go to step 3. iv Upgrade The Password window appears; see Figure Figure Upgrade window The ONT supports upgrades using the web. First, put the software image on the internal PC and enable the FTP server. Second, click Upgrade to get the software image from the local PC using FTP and display it before the image is upgraded. You can also refresh the display of the software image by clicking Refresh. 2 Click Apply to save your changes or Refresh to clear the fields. 3 STOP. This procedure is complete. Status reports using the web-based GUI The following procedures provide the steps for obtaining ONT status information. Procedure 34-6 Status report generation 1 Select one of the following options from the Status section of the navigation tree in the GPON ONT window. i Device Info The Device Info window appears; see Figure Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

189 34 I-240G-P, I-240G-Q, I-240G-T, I-241G-P, and I-241G-R unit data sheet Figure Device Info window Go to step 3 when you are finished reading the information in the window. Table describes the fields in the Device Info window. Table Device Info window fields Field Software Version: Build Date: MAC Address Current Time Description Current version of the software Date stamp on the software load MAC address of the WAN interface Time when the information was collected ii WAN Status The WAN Status window appears; see Figure November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

190 34 I-240G-P, I-240G-Q, I-240G-T, I-241G-P, and I-241G-R unit data sheet Figure WAN Status window Table describes the fields in the WAN Status window. Go to step 2 if you require updated information. Table WAN Status window fields Field Internet Connection Type Connection Status MAC Address IP Address Subnet Mask Default Gateway DNS Server 1 DNS Server 2 Description Type of internet connection used by the WAN interface. Options are: PPPOE DHCP Static IP Status is either Connected or Disconnected MAC address of the WAN interface IP address of the WAN interface Subnet mask of the WAN interface IP address of the node on the computer network that is chosen as default when the IP address does not match any other routes in the routing table IP address of the first DNS server IP address of the second DNS server iii PON Statistics The PON Statistics window appears; see Figure Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

191 34 I-240G-P, I-240G-Q, I-240G-T, I-241G-P, and I-241G-R unit data sheet Figure PON Statistics window Table describes the fields in the PON Statistics window. Go to step 2 if you require updated information. Table PON Statistics window fields Field Tx Packets Rx Packets Tx Lost Packets Rx Lost Packets Rx Error Packets Description Number of packets that have been transmitted Number of packets that have been received Number of packets lost during transmission Number of packets lost prior to reception Number of packets that have been received with errors 2 Click Refresh to clear the fields and obtain updated data. 3 STOP. This procedure is complete November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

192 NTP 178 Install an I-240G-P, I-24OG-Q, I-240G-T, I-241G-P, or I-241G-R indoor ONT Purpose This NTP provides the steps to install I-240G-P, I-240G-Q, I-240G-T, I-241G-P, or I-241G-R indoor ONTs. General The DLPs listed in this NTP describe mounting and cabling for I-240G-P, I-240G-Q, I-240G-T, I-241G-P, and I-241G-R indoor ONTs. Prerequisites See the listed DLPs for prerequisites. Recommended tools You need the following tools for the installation: #2 Phillips screwdriver 1/4 in. (6 mm) flat blade screwdriver wire strippers fiber optic splicing tools RJ-45 cable plug crimp tool voltmeter or multimeter optical power meter wall mounting template drill and drill bits Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November 2013 NTP FE AAAA TCZZA Edition 01

193 NTP 178 Install an I-240G-P, I-24OG-Q, I-240G-T, I-241G-P, or I-241G-R indoor ONT Safety information Read the following safety information before installing the unit. Danger 1 Contact the local utility company before you connect the enclosure to the utilities. Danger 2 Observe the local and national laws and regulations that may be applicable to this installation. Danger 3 If the coaxial output of the ONT is connected to the dwelling infrastructure coaxial distribution system, ensure that the coaxial distribution system is separately grounded. Grounding of the dwelling coaxial infrastructure shall use Listed grounding devices and must be installed in accordance with local Codes and Article 800 of the National Electric Code, ANSI/NFPA 70, following the manufacturers instructions. Warning This equipment is ESD sensitive. Proper ESD protections should be used when removing the fiber access cover of the indoor ONT. Caution Keep indoor ONTs out of direct sunlight. Prolonged exposure to direct sunlight can damage the unit. Procedure Note Observe the following: The indoor ONT should be installed in accordance with the applicable requirements of the NEC or CEC. Local authorities and practices take precedent when there is conflict between the local standard and the NEC or CEC. The indoor ONT must be installed by qualified service personnel. Indoor ONTs must be installed with cables that are suitably rated and listed for indoor use. See I-240G-P, I-240G-Q, I-240G-T, I-241G-P and I-241G-R detailed specifications in the unit data sheet for the temperature ranges for this ONT. Use this procedure to install an I-240G-P, I-240G-Q, I-240G-T, I-241G-P, or I-241G-R indoor ONT. 1 Prepare the cables at the site where the ONT will be installed (DLP 100). 2 Locate any missing cables and route them to the ONT as per local practices. NTP November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

194 OPTICAL LAN UPDATE ALARM POTS POWER NTP 178 Install an I-240G-P, I-24OG-Q, I-240G-T, I-241G-P, or I-241G-R indoor ONT 3 Place the indoor ONT unit: a On the flat surface, such as a desk, horizontally resting on its four feet as shown in Figure NTP 178-1; go to step 4. Note The I-240G-P cannot be stacked with another ONT or with other equipment. The ONT mounting requirements are: allow a minimum 100 mm clearance above the top cover allow a minimum 50 mm clearance from the side vents do not place any heat source directly above the top cover or below the bottom cover Figure NTP 178-1: I-240G-P, I-240G-Q, or I-240G-T indoor ONT on a desk b On a wall (DLP 122). 4 Review the connection locations as shown in Figure NTP for I-240G-P or I-240G-Q indoor ONTs, Figure NTP for I-240G-T indoor ONTs, and Figure NTP for I-241G-P and I-241G-R indoor ONTs Figure NTP 178-2: I-240G-P or I-240G-Q indoor ONT connections POWER OPTICAL LAN UPDATE ALARM POTS GE1 GE2 GE3 GE4 POTS1 POTS2 RESET PWR Ethernet ports (RJ45) POTS ports (RJ-11) Fiber optic connector Power connector Reset button Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November 2013 NTP FE AAAA TCZZA Edition 01

195 NTP 178 Install an I-240G-P, I-24OG-Q, I-240G-T, I-241G-P, or I-241G-R indoor ONT Figure NTP 178-3: I-240G-T indoor ONT connections POWER OPTICAL LAN UPDATE ALARM POTS GE1 GE2 GE3 GE4 POTS1 POTS2 Ethernet ports (RJ45) ON/OFF RESET PWR Reset button POTS ports (RJ-11) Power ON/OFF button Power connector Fiber optic connector Figure NTP 178-4: I-241G-P and I-241G-R indoor ONT connections GE POTS Ethernet ports (RJ45) POTS ports (RJ-11) F-Type coaxial connector Power connector A B RF Fiber optic connector (internal) PWR 12VDC GPON 2.5G/1.25G G B+ Class 1 Laser The I-241G-R ONT is identical to the I-241G-P ONT except that its RF video connector is plugged with a filter and is not used. 5 Connect the Ethernet cables to the RJ-45 ports (DLP 101). 6 Connect the POTS cables to the RJ-11 ports (DLP 123). 7 For I-241G-P and I-241G-R ONTs only, connect the coaxial cable to the F-Type connector (DLP 116). 8 Connect the SC/APC fiber optic cable (DLP 125). Warning Be careful to maintain a bend radius of no less than 1.5 inches (3.8 cm) when connecting the fiber optic cable. Too small of a bend radius in the cable can result in damage to the optic fiber. NTP November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

196 NTP 178 Install an I-240G-P, I-24OG-Q, I-240G-T, I-241G-P, or I-241G-R indoor ONT 9 Install the power supply according to manufacturer specifications. Note Observe the following: Units must be powered by a Listed or CE approved and marked limited power source power supply with a minimum output rate of 12 V dc, 1.25 A. 10 Connect the power cable to the power connector. 11 For the I-240G-T indoor ONT, power up the unit by pressing the ON/OFF power switch. 12 If used, configure the SLID (chapter 6). 13 Verify the ONT LEDs, voltage status, and optical signal levels (DLP 127). 14 Activate and test the services (DLP 128). 15 If necessary, reset the ONT (DLP 126). 16 STOP. This procedure is complete. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November 2013 NTP FE AAAA TCZZA Edition 01

197 NTP 178 Install an I-240G-P, I-24OG-Q, I-240G-T, I-241G-P, or I-241G-R indoor ONT NTP November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

198 NTP 179 Replace an I-240G-P, I-240G-Q, I-240G-T, I-241G-P, or I-241G-R indoor ONT Purpose This NTP provides the steps to replace I-240G-P, I-240G-Q, I-240G-T, I-241G-P, or I-241G-R indoor ONTs. General The DLPs listed in this NTP describe mounting and cabling for I-240G-P, I-240G-Q, I-240G-T, I-241G-P, or I-241G-R indoor ONTs. Prerequisites See the listed DLPs for prerequisites. Recommended tools You need the following tools for replacing the ONT: #2 Phillips screwdriver 1/4 in. (6 mm) flat blade screwdriver wire strippers fiber optic splicing tools RJ-45 cable plug crimp tool voltmeter or multimeter optical power meter wall mounting template drill and drill bits Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November 2013 NTP FE AAAA TCZZA Edition 01

199 NTP 179 Replace an I-240G-P, I-240G-Q, I-240G-T, I-241G-P, or I-241G-R indoor ONT Safety information Read the following safety information before replacing the unit. Danger 1 Contact the local utility company before you connect the enclosure to the utilities. Danger 2 Observe the local and national laws and regulations that may be applicable to this installation. Danger 3 If the coaxial output of the ONT is connected to the dwelling infrastructure coaxial distribution system, ensure that the coaxial distribution system is separately grounded. Grounding of the dwelling coaxial infrastructure shall use Listed grounding devices and must be installed in accordance with local Codes and Article 800 of the National Electric Code, ANSI/NFPA 70, following the manufacturers instructions. Warning This equipment is ESD sensitive. Proper ESD protections should be used when removing the fiber access cover of the indoor ONT. Caution Keep indoor ONTs out of direct sunlight. Prolonged exposure to direct sunlight can damage the unit. Procedure Note Observe the following: The indoor ONT should be installed in accordance with the applicable requirements of the NEC or CEC. Local authorities and practices take precedent when there is conflict between the local standard and the NEC or CEC. The indoor ONT must be installed by qualified service personnel. Indoor ONTs must be installed with cables that are suitably rated and listed for indoor use. See I-240G-P, I-240G-Q, I-240G-T, I-241G-P and I-241G-R detailed specifications in the unit data sheet for the temperature ranges for this ONT. Use this procedure to replace an I-240G-P, I-240G-Q, I-240G-T, I-241G-P, or I-241G-R indoor ONT. 1 Deactivate the ONT services (DLP 131). If you are using the SLID feature, this step is not required. The ONT and the services can remain in service (IS). 2 For the I-240G-T indoor ONT, power down the unit by pressing the ON/OFF power switch. NTP November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

200 NTP 179 Replace an I-240G-P, I-240G-Q, I-240G-T, I-241G-P, or I-241G-R indoor ONT 3 Disconnect the POTS, Ethernet, fiber optic cables (DLP 133), and power cables from the ONT; see Figure NTP for the connector locations on I-240G-P and I-240G-Q ONTs, Figure NTP for I-240G-T indoor ONTs, and Figure NTP for I-241G-P and I-241G-R ONTs. Figure NTP 179-1: I-240G-P and I-240G-Q indoor ONT connections POWER OPTICAL LAN UPDATE ALARM POTS GE1 GE2 GE3 GE4 POTS1 POTS2 RESET PWR Ethernet ports (RJ45) POTS ports (RJ-11) Fiber optic connector Power connector Reset button Figure NTP 179-2: I-240G-T indoor ONT connections POWER OPTICAL LAN UPDATE ALARM POTS RESET PWR GE1 GE2 GE3 GE4 POTS1 POTS2 Ethernet ports (RJ45) Reset button ON/OFF POTS ports (RJ-11) Power ON/OFF button Power connector Fiber optic connector Figure NTP 179-3: I-241G-P and I-241G-R indoor ONT connections GE POTS Ethernet ports (RJ45) POTS ports (RJ-11) F-Type coaxial connector Power connector A B RF Fiber optic connector (internal) PWR 12VDC GPON 2.5G/1.25G G B+ Class 1 Laser Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November 2013 NTP FE AAAA TCZZA Edition 01

201 NTP 179 Replace an I-240G-P, I-240G-Q, I-240G-T, I-241G-P, or I-241G-R indoor ONT The I-241G-R ONT is identical to the I-241G-P ONT except that its RF video connector is plugged with a filter and is not used. 4 Replace the ONT with a new unit: a On a flat surface, such as a desk, substitute a replacement ONT for the old ONT; go to step 5. Note The I-240G-P cannot be stacked with another ONT or with other equipment. The ONT mounting requirements are: b allow a minimum 100 mm clearance above the top cover allow a minimum 50 mm clearance from the side vents do not place any heat source directly above the top cover or below the bottom cover On a wall. i ii Slide the old ONT off of the mounting screws until the ONT is free of the wall. Install the replacement ONT following the wall mounting instructions for I-240G-P, I-240G-Q, I-240G-T, I-241G-P, and I-241G-R indoor ONTs (DLP 122). 5 Connect the Ethernet cables to the RJ-45 ports (DLP 101). 6 Connect the POTS cables to the RJ-11 ports (DLP 123). 7 For I-241G-P and I-241G-R ONTs only, connect the coaxial cable to the F-Type connector (DLP 116). 8 If required, have approved service personnel who are trained to work with optic fiber clean the fiber optic connection. See DLP 134 for more information about fiber optic handling, inspection, and cleaning. Danger Fiber optic cables transmit invisible laser light. To avoid eye damage or blindness, never look directly into fibers, connectors, or adapters. 9 Connect the SC/APC fiber optic cable (DLP 125). Warning Be careful to maintain a bend radius of no less than 1.5 inches (3.8 cm) when connecting the fiber optic cable. Too small of a bend radius in the cable can result in damage to the optic fiber. 10 Install the power supply according to manufacturer specifications. Note Observe the following: Units must be powered by a Listed or CE approved and marked limited power source power supply with a minimum output rate of 12 V dc, 1.25 A. NTP November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

202 NTP 179 Replace an I-240G-P, I-240G-Q, I-240G-T, I-241G-P, or I-241G-R indoor ONT 11 Connect the power cable to the power connector. 12 For the I-240G-T indoor ONT, power up the unit by pressing the ON/OFF power switch. 13 If necessary, reset the ONT (DLP 126). 14 If used, configure the SLID (chapter 6). Note A new SLID or the old SLID may be used with the replacement ONT. If a new SLID is used, the new SLID must also be programmed at the P-OLT using TL1 or a network manager. If the old SLID is used, no changes need to be made at the P-OLT; see the operations and maintenance documentation for the OLT for more details. 15 Verify the ONT LEDs, voltage status, and optical signal levels (DLP 127). 16 Activate and test the services (DLP 128). 17 STOP. This procedure is complete. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November 2013 NTP FE AAAA TCZZA Edition 01

203 NTP 179 Replace an I-240G-P, I-240G-Q, I-240G-T, I-241G-P, or I-241G-R indoor ONT NTP November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

204 NTP 180 Configure an I-240G-P, I-240G-Q, I-240G-T, I-241G-P, or I-241G-R indoor ONT General Please refer to the OLT Operations and Maintenance using TL1 and CLI guide for the software configuration procedure for I-240G-P, I-240G-Q, I-240G-T, I-241G-P, and I-241G-R indoor ONTs. For HTTP configuration procedures, please refer to chapter 6, ONT management using an ONT interface. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November 2013 NTP FE AAAA TCZZA Edition 01

205 NTP 180 Configure an I-240G-P, I-240G-Q, I-240G-T, I-241G-P, or I-241G-R indoor ONT NTP November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

206 I-240G-R, I-240G-U 35 I-240G-R and I-240G-U unit data sheet NTP 181 Install an I-240G-R or I-240G-U indoor ONT NTP 182 Replace an I-240G-R or I-240G-U indoor ONT NTP 183 Configure an I-240G-R or I-240G-U indoor ONT Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

207 November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

208 35 I-240G-R and I-240G-U unit data sheet 35.1 I-240G-R and I-240G-U part numbers and identification I-240G-R and I-240G-U general description I-240G-R and I-240G-U software and installation feature support I-240G-R and I-240G-U interfaces and interface capacity I-240G-R and I-240G-U LEDs I-240G-R and I-240G-U detailed specifications I-240G-R and I-240G-U GEM ports and T-CONTs I-240G-R and I-240G-U power support I-240G-R and I-240G-U functional blocks I-240G-R and I-240G-U standards compliance I-240G-R and I-240G-U special considerations Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

209 35 I-240G-R and I-240G-U unit data sheet 35.1 I-240G-R and I-240G-U part numbers and identification Table 35-1 provides part numbers and identification information for I-240G-R and I-240G-U indoor ONTs. Table 35-1 I-240G-R and I-240G-U part numbers and identification Mnemonic Ordering kit part number Provisioning part number Description CLEI CPR ECI/ Bar code I-240G-R 3FE AB 3FE AP GPON I-series ONT, version R, 2 POTS and 4 GigE Ethernet interfaces. Includes ac/dc power cord with European (EU) variant plug. 3FE AC GPON I-series ONT, version R, 2 POTS and 4 GigE Ethernet interfaces. Includes ac/dc power cord with Australian (AU) variant plug. 3FE AD GPON I-series ONT, version R, 2 POTS and 4 GigE Ethernet interfaces. Includes ac/dc power cord with United Kingdom (UK) variant plug. 3FE AF GPON I-series ONT, version R, 2 POTS and 4 GigE Ethernet interfaces. Includes ac/dc power cord with United States (US) variant plug. 3FE AE (customerspecific variant) 3FE BK GPON I-series ONT, version R, 2 POTS and 4 GigE Ethernet interfaces. Includes ac/dc power cord with Australian (AU) variant plug. This ONT is shipped with a fiber storage tray. 3FE AB (customerspecific variant) 3FE AB GPON I-series ONT, version R, 2 POTS and 4 GigE Ethernet interfaces. Includes ac/dc power cord with Australian (AU) variant plug. This ONT only supports wall mounting in an ALU qualified customer-specific enclosure or an I-240G-R fiber storage tray. I-240G-U 3FE AA 3FE AA GPON I-series ONT, version U, 2 POTS and 4 GigE Ethernet interfaces. Includes ac/dc power cord with European (EU) variant plug. 3FE CA 3FE EA GPON I-series ONT, version U, 2 POTS and 4 GigE Ethernet interfaces. Includes ac/dc power cord with United Kingdom (UK) variant plug. GPON I-series ONT, version U, 2 POTS and 4 GigE Ethernet interfaces. Includes ac/dc power cord with United States (US) variant plug November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

210 35 I-240G-R and I-240G-U unit data sheet 35.2 I-240G-R and I-240G-U general description The I-240G-R and I-240G-U indoor ONTs provide a subscriber interface for the network by terminating the PON interface and converting it to user interfaces that directly connect to subscriber devices. The ONT is compatible with all existing subscriber equipment, including analog phones with both tone and rotary dial capabilities, cordless phones, modems, fax machines, and caller ID boxes (Type I, Type II, and Type III). The I-240G-R and I-240G-U indoor ONT provides the following functions: fully G.984 series GPON standard compliant IGMP v2/v3 snooping dedicated Multicast GEM port on the downstream Broadcast/Multicast rate limiting auto-negotiation and MDI/MDIX auto-sensing Gb/s downstream receiver and Gb/s burst mode upstream transmitter 35.3 I-240G-R and I-240G-U software and installation feature support Table 35-2 provides a list of software-based features and installation information supported by I-240G-R and I-240G-U indoor ONTs. Table 35-2 I-240G-R and I-240G-U indoor ONT software feature support Features Chapter Cross reference for more information General ONT and MDU overview Service interface specifications General information common to multiple devices and an explanation of general system behaviors. ONT and MDU general and interface technical specifications ONT and MDU overview Ethernet interface specifications POTS interface specifications RSSI specifications Wi-Fi specifications Optical budget Location and installation options ONT and MDU general and interface technical specifications How to install and replace I-240G-R indoor ONTs ONT optical budget Install an I-240G-R or I-240G-U indoor ONT Replace an I-240G-R or I-240G-U indoor ONT Activation method ONT and MDU overview ONT activation and behavior using SLID HTTP ONT management procedures Statistics and performance monitoring (1 of 2) Information necessary to manage an ONT at a local site using an HTTP interface, CLI interface, CLI interface, or butt set. ONT and MDU statistics and performance monitoring ONT management using an ONT interface Performance monitoring statistics for Package D ONTs Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

211 35 I-240G-R and I-240G-U unit data sheet Features Chapter Cross reference for more information Supported UPS (2 of 2) Part numbers, ordering, and deployment configuration overview ONT and MDU to UPS or power adapter compatibility support 35.4 I-240G-R and I-240G-U interfaces and interface capacity Table 35-3 describes the supported interfaces and the maximum connection capacity for I-240G-R and I-240G-U indoor ONTs. Table 35-3 I-240G-R and I-240G-U indoor ONT interface connection capacity ONT type and model Maximum capacity POTS 10/ 100 BASE-T 10/ 100/ 1000 BASE-T RF video (CATV) MoCA VDSL2 DS1/ E1 Local craft GPON SC/ APC I-240G-R I-240G-U I-240G-R and I-240G-U indoor ONTs are for indoor deployment and can be installed horizontally on a flat surface as well as attached to a wall. Figure 35-1 shows the connections for I-240G-R and I-240G-U indoor ONTs. Figure 35-1 I-240G-R and I-240G-U indoor ONT physical connections UNI-V UNI-D 1 2 RESET POWER POTS ports (RJ-11) Reset button Ethernet ports (RJ-45) Power connector Fiber optic connector Table 35-4 describes the physical connections on I-240G-R and I-240G-U indoor ONTs. Table 35-4 I-240G-R and I-240G-U indoor ONT physical connections Connection (1) POTS Description This connection is provided through RJ-11 ports. Up to two POTS connections are supported.the POTS ports support voice services. (1 of 2) 35-4 November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

212 35 I-240G-R and I-240G-U unit data sheet Connection (1) Ethernet ports Power Fiber optic Description This connection is provided through Ethernet RJ-45 cables. Up to four 10/100/1000 Base-T Ethernet interfaces are supported.the Ethernet ports can support both data and in-band video services on all four interfaces. This connection to the ONT is provided through a + 12 V dc UPS power connector. A power cable is fitted with an eight-pin connector. This connection is provided through a SC/APC fiber optic connector with SFF-type laser. The fiber optic connector is located behind a fiber optic port cover on these ONTs. (2 of 2) Note (1) The primary path for the earth ground for these ONTs is provided by the 12V Return signal in the power connector I-240G-R and I-240G-U LEDs Figure 35-2 shows the I-240G-R and I-240G-U indoor ONT LEDs. Figure 35-2 I-240G-R and I-240G-U indoor ONT LEDs POWER OPTICAL ALARM UNI-D 1 UNI-D 2 UNI-D 3 UNI-D 4 UNI-V 1/2 UPDATE I-240G-R UNI-V 1 UNI-V 2 UNI-D 1 UNI-D 2 UNI-D 3 UNI-D Table 35-5 provides I-240G-R and I-240G-U indoor ONT LED descriptions. Table 35-5 I-240G-R and I-240G-U indoor ONT LEDs Indicator LED color and behavior LED behavior description POWER (1 of 2) Off Red solid Green solid Green flashing No power Operating from battery Operating on ac power ONT is starting up Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

213 35 I-240G-R and I-240G-U unit data sheet Indicator LED color and behavior LED behavior description OPTICAL ALARM UNI-D1 to UNI-D4 UNI-V1/2 UPDATE (2 of 2) Off Red solid Green solid Green flashing Off Red solid Green solid Off Yellow solid Yellow flashing Green solid Green flashing Off Green solid Green flashing Off Red solid Green flashing ONT disabled by OLT PON Loss of link Optical link is connected and ranged Activity on PON (any data including OMCI) ONT is operating without failure ONT hardware failure No alarm, with local Ethernet access enabled No service provisioned or no link detected 1G link detected 1G data activity 10/100 link detected 10/100 data activity No POTS provisioned (all phones are on-hook or no phones connected) One or more phones are off-hook One or more phones are off-hook for the minimum of one hour Normal status ONT software download failure ONT software downloading 35.6 I-240G-R and I-240G-U detailed specifications Table 35-6 lists the physical specifications for I-240G-R and I-240G-U indoor ONTs. Table 35-6 I-240G-R and I-240G-U indoor ONT physical specifications) Dimensions Height Width Depth Specifications 5.1 in. (13 cm) 6.8 in. (17.2 cm) 1.4 in. (3.6 cm) Weight [within ± 0.5 lb (0.23 kg)] 0.7 lb (335 g) Table 35-7 lists power consumption specifications for I-240G-R and I-240G-U indoor ONTs November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

214 35 I-240G-R and I-240G-U unit data sheet Table 35-7 I-240G-R and I-240G-U indoor ONT power consumption specifications Mnemonic Maximum power (not to exceed) Condition Minimum power Condition I-240G-R 10.5 W 2 POTS off-hook, 4 Gig-E operational I-240G-U 10.5 W 2 POTS off-hook, 4 Gig-E operational 5.5 W 2 POTS on-hook, other interfaces/services not provisioned 5.5 W 2 POTS on-hook, other interfaces/services not provisioned Table 35-8 lists the environmental requirements for I-240G-R and I-240G-U indoor ONTs. Table 35-8 I-240G-R and I-240G-U indoor ONT environmental requirements ONT type Mounting method Temperature range and humidity Altitude I-240G-R (except 3FE AB) and I-240G-U desk or wall mounted I-240G-R 3FE AB variant wall mounted in an ALU-qualified customer-specific enclosure or an I-240G-R fiber storage tray only Operating: 32 F to 104 F (0 C to 40 C) ambient temperature 10% to 90% relative humidity, non-condensing Storage: Contact your Alcatel-Lucent support representative for more information Operating: 32 F to F (0 C to 42 C) ambient temperature 10% to 90% relative humidity, non-condensing Storage: Contact your Alcatel-Lucent support representative for more information Minimum operating altitude is 197 ft (60 m) below sea level to a maximum of 6000 ft (1800 m) above mean sea level Minimum operating altitude is 197 ft (60 m) below sea level to a maximum of 6000 ft (1800 m) above mean sea level 35.7 I-240G-R and I-240G-U GEM ports and T-CONTs Table 35-9 lists the maximum number of supported T-CONTs and GEM ports for I-240G-R and I-240G-U indoor ONTs. Not all ONTs will be supported in all of the releases indicated the table. See the appropriate release Customer Release Notes for the most accurate list of supported devices. Table 35-9 I-240G-R and I-240G-U indoor ONT capacity for GEM ports and T-CONTs per package and release ONT or MDU Release (1) Maximum Notes Package D ONTs (1 of 2) Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

215 35 I-240G-R and I-240G-U unit data sheet ONT or MDU Release (1) Maximum Notes GEM ports per indoor or outdoor ONT R x, R are present: 30 are available, 2 are reserved for multicast and debugging R , R a are present T-CONTs per indoor or outdoor ONT R x, R are present: 31 are available, 1 is reserved for OMCI (2 of 2) Note (1) The letter x following a release number denotes either a letter of the alphabet for maintenance releases or digit from 0 to 9 for minor releases I-240G-R and I-240G-U power support See Part numbers, ordering, and deployment configuration overview for the specific power supplies supported by the I-240G-R and I-240G-U indoor ONTs I-240G-R and I-240G-U functional blocks I-240G-R and I-240G-U indoor ONTs transmit Ethernet packets to four RJ-45 Ethernet ports and voice traffic to two RJ-11 POTS ports. These ONTs also feature fiber optic and power connectors. ONT SoC technology consists of five key elements: GPON MAC The Gigabit Passive Optical Network Media Access Control (GPON MAC) element on the SoC terminates the GPON interface using an optical diplexer. This interface supports GPON as described in G (GPON TC Layer) ITU specification. Ethernet MAC The SoC provides up to four GE MACs. DSP interface The Digital Signal Processor (DSP) provides voice processing for 2 POTS lines with the 3-way calling. The DSP has a dedicated 64 kbyte instruction cache and shares a 32 kbyte data cache with the Control Processor. Control Processor The Control Processor features an integral memory management unit that supports a dedicated 64 kbyte instruction cache and shares a single 32 kbyte data cache with the DSP. The Control Processor and DSP also include a single channel Data Management Application (DMA) controller with a 4 kbyte read ahead low-latency Dynamic Random Access Memory (DRAM) access port. The processors typically run at 400 MHz. Switch matrix The Switch matrix provides an integrated data channel between the four GE MACs, GPON MAC, DSP, the control processor, and the other integrated elements such as flash memory, DRAM, and the local bus controller November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

216 35 I-240G-R and I-240G-U unit data sheet Single-residence Gigabit Ethernet ONTs with POTS and with or without RF video represent another variation of the Package D ONT. In the case of I-240G-R ONTs, there is no RF video port in addition to POTS and Ethernet ports. These Package D ONTs transmit Ethernet packets to up to four RJ-45 Ethernet ports, and voice traffic to either one or two RJ-11 POTS ports. These ONTs also feature fiber optic and power connectors. Figure 35-3 shows the functional blocks for an I-240G-R and I-240G-U indoor ONT with four Gigabit Ethernet and two POTS ports. Figure 35-3 Single-residence Gigabit Ethernet ONT with POTS and Ethernet ports SC/APC Diplexer GPON SOC SLIC GE switch 2xRJ11 4xRJ45 PWR I-240G-R and I-240G-U standards compliance I-240G-R and I-240G-U indoor ONTs are compliant with the following standards: 802.1d support for bridging 802.1p support for mapping and mapper service profile on U/S 802.1p support for marking and remarking 802.1p support for Class of Service based on VLAN-ID 802.1q support for virtual switch based on VLAN G.711 support for FAX, modem connection, and TTY devices G.984 support GPON interface (framing) G support for Amd1, Class B+ G support for activation and password functions G support for AES with operator enable/disable on per port-id level G support for FEC in both upstream and downstream directions G support for multicast using a single GEM Port-ID for all video traffic G984.4 and G support for OMCI interface for ONT management and provisioning G support for blocking filter as an option Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

217 35 I-240G-R and I-240G-U unit data sheet I-240G-R and I-240G-U special considerations Upgrade considerations and limitations Existing ONTs that use 7342 ISAM FTTU releases older than R04.06.xx and R04.07.xx must be upgraded to use R software while assigned to a PON ID value smaller than 64. For this purpose, if split ratios larger than 1:64 are being deployed, you may choose to set aside the first PON ID as a staging point. I-240G-R and I-240G-U ONT considerations and limitations Table lists the considerations and limitations for the I-240G-R and I-240G-U indoor ONTs. Table I-240G-R and I-240G-U indoor ONT considerations and limitations Considerations and limitations Support for up to 32 GEM ports Support for 32 T-CONTs Ethernet OA&M (802.1 ag) is not supported V+G-based downstream multicast VLAN translation is not supported The ONT pads packets to 104 as SoC limitation IGMPv3 snooping with SSM is not supported. IGMPv3 snooping without SSM is supported x is not supported ONT does not support service classification by Ethertype The uplink port of the SoC chipset is limited to 1 Gb/s IPv6 is not supported 100M half is not supported When the internal downstream traffic exceeds 1 Gb/s, the ONT drops lower priority packets from the QoS queues and buffer pools November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

218 NTP 181 Install an I-240G-R or I-240G-U indoor ONT Purpose This NTP provides the steps to install an I-240G-R or I-240G-U indoor ONT. General The steps listed in this NTP describe how to install an I-240G-R or I-240G-U indoor ONT. Prerequisites See the listed DLPs for prerequisites. Recommended tools You need the following tools for the installation: #2 Phillips screwdriver 1/4 in. (6 mm) flat blade screwdriver wire strippers fiber optic splicing tools RJ-45 cable plug crimp tool voltmeter or multimeter optical power meter wall mounting template drill and drill bits Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November 2013 NTP FE AAAA TCZZA Edition 01

219 NTP 181 Install an I-240G-R or I-240G-U indoor ONT Safety information Read the following safety information before installing the unit. Danger 1 Always contact the local utility company before you connect the enclosure to the utilities. Danger 2 Observe the local and national laws and regulations that may be applicable to this installation. Warning Do not install electrical equipment in wet or damp conditions. Caution Observe the following: Always use caution when handling live electrical connections. Do not allow anything to rest on the power cable or install the ONT in a place where people will stand or walk on the power cable. With this ONT use only the certified adapter model, which complies with the requirement of limited power source, included inside the package. Note Observe the following: The ONT should be installed in accordance with the applicable requirements of the NEC or CEC. Local authorities and practices take precedence when there is conflict between the local standard and the NEC or CEC. The ONT must be installed by qualified service personnel only. Indoor ONTs must be installed with cables that are suitably rated and listed for indoor use. Ensure that the power source for the system is adequately-rated to assure safe operation and provides current overload protection. NTP November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

220 NTP 181 Install an I-240G-R or I-240G-U indoor ONT Procedure Use this procedure to install an I-240G-R or I-240G-U indoor ONT. 1 Prepare the cables at the site where the ONT will be installed (DLP 100). Also, locate the power source where the power supply will be installed. 2 Place the indoor ONT unit: Note The I-240G-R 3FE AB variant can only be wall mounted in an ALU qualified customer-specific enclosure or I-240G-R fiber storage tray. It cannot be used on a desk. a On the flat surface, such as a desk, horizontally resting on its four plastic feet; go to step 3. Note The I-240G-R (excluding the 3FE AB variant) or I-240G-U cannot be stacked with another ONT or with other equipment. The ONT mounting requirements are: allow a minimum 100 mm clearance above the top cover allow a minimum 50 mm clearance from the side vents do not place any heat source directly above the top cover or below the bottom cover b On a wall (DLP 122). Note The I-240G-R 3FE AB variant can only be mounted vertically in an ALU qualified customer-specific enclosure or I-240G-R fiber storage tray. The ONT mounting requirements are: allow a minimum 100 mm clearance from the front face of the enclosure or wall-mounted ONT allow a minimum 50 mm clearance from the top, bottom, left, and right faces of the enclosure or wall-mounted ONT do not place any heat source directly next to the ONT or enclosure do not place the ONT on a desk or stack with other ONTs 3 Review the connection locations shown in Figure NTP Figure NTP 181-1: I-240G-R and I-240G-U indoor ONT connections UNI-V UNI-D 1 2 RESET POWER POTS ports (RJ-11) Reset button Ethernet ports (RJ-45) Power connector Fiber optic connector Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November 2013 NTP FE AAAA TCZZA Edition 01

221 NTP 181 Install an I-240G-R or I-240G-U indoor ONT 4 Connect the SC/APC fiber optic cable (DLP 125). Warning Be careful to maintain a bend radius of no less than 1.5 inches (3.8 cm) when connecting the fiber optic cable. Too small of a bend radius in the cable can result in damage to the optic fiber. Caution Invisible laser radiation may be emitted from the ends of un-terminated fiber cables or connectors. Never look directly into an un-terminated cable or connector. 5 Verify that the power cable terminates with an 8-pin connector as shown in Figure NTP and described in Table NTP Figure NTP 181-2: 8-pin connector Pin 8 Pin5 Pin 4 Pin Table NTP 181-1: Pin assignments on the 8-pin connector Pin # Definition Pin # Definition 1 Power input (+ 12V) 5 12 V power return 2 UPS status: On battery 6 Alarm ground 3 UPS status: Battery missing 7 UPS status: Replace battery 4 GNC / Optional frame ground 8 UPS status: Low battery 6 Connect the power cable to the power connector on the ONT. Note Observe the following: Units must be powered by a Listed or CE approved and marked limited power source power supply with a minimum output rate of 12 V dc, 1.25 A. 7 Connect the POTS cables to the RJ-11 ports (DLP 123). 8 Connect the Ethernet cables to the RJ-45 ports (DLP 101). 9 If used, configure the SLID (DLP 129). 10 Verify the ONT LEDs, voltage status, and optical signal levels (DLP 127). 11 Activate and test the services (DLP 128). NTP November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

222 NTP 181 Install an I-240G-R or I-240G-U indoor ONT 12 If necessary, reset the ONT (DLP 126). 13 STOP. This procedure is complete. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November 2013 NTP FE AAAA TCZZA Edition 01

223 NTP 181 Install an I-240G-R or I-240G-U indoor ONT NTP November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

224 NTP 182 Replace an I-240G-R or I-240G-U indoor ONT Purpose This NTP provides the steps to replace an I-240G-R or I-240G-U indoor ONT. General The steps listed in this NTP describe how to replace an I-240G-R or I-240G-U indoor ONT. Prerequisites See the listed DLPs for prerequisites. Recommended tools You need the following tools for the installation: #2 Phillips screwdriver 1/4 in. (6 mm) flat blade screwdriver wire strippers fiber optic splicing tools RJ-45 cable plug crimp tool voltmeter or multimeter optical power meter wall mounting template drill and drill bits Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November 2013 NTP FE AAAA TCZZA Edition 01

225 NTP 182 Replace an I-240G-R or I-240G-U indoor ONT Safety information Read the following safety information before installing the unit. Danger 1 Always contact the local utility company before you connect the enclosure to the utilities. Danger 2 Observe the local and national laws and regulations that may be applicable to this installation. Warning Do not install electrical equipment in wet or damp conditions. Caution Observe the following: Always use caution when handling live electrical connections. Do not allow anything to rest on the power cable or install the ONT in a place where people will stand or walk on the power cable. With this ONT use only the certified adapter model, which complies with the requirement of limited power source, included inside the package. Procedure Note Observe the following: The ONT should be installed in accordance with the applicable requirements of the NEC or CEC. Local authorities and practices take precedence when there is conflict between the local standard and the NEC or CEC. The ONT must be installed by qualified service personnel only. Indoor ONTs must be installed with cables that are suitably rated and listed for indoor use. Ensure that the power source for the system is adequately-rated to assure safe operation and provides current overload protection. Use this procedure to replace an I-240G-R or I-240G-U indoor ONT. 1 Deactivate the ONT services (DLP 131). If you are using the SLID feature, this step is not required. The ONT and the services can remain in service (IS). 2 Disconnect the cables from the ONT in the following order; see Figure NTP for the connector locations on I-240G-R or I-240G-U ONT. i ii iii iv Disconnect the power cable from the power connector. Disconnect the Ethernet cables from the RJ-45 ports. Disconnect the POTS cables from the RJ-11 ports. Disconnect the SC/APC fiber optic cable from the fiber optic connector. NTP November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

226 NTP 182 Replace an I-240G-R or I-240G-U indoor ONT Figure NTP 182-1: I-240G-R or I-240G-U indoor ONT connections UNI-V UNI-D 1 2 RESET POWER POTS ports (RJ-11) Reset button Ethernet ports (RJ-45) Power connector Fiber optic connector Replace the ONT with a new unit: Note The I-240G-R 3FE AB variant can only be mounted vertically in an ALU qualified customer-specific enclosure or I-240G-R fiber storage tray. The ONT mounting requirements are: a allow a minimum 100 mm clearance from the front face of the enclosure or wall-mounted ONT allow a minimum 50 mm clearance from the top, bottom, left, and right faces of the enclosure or wall-mounted ONT do not place any heat source directly next to the ONT or enclosure do not place the ONT on a desk or stack with other ONTs On a flat surface, such as a desk, substitute a replacement ONT for the old ONT. Note The I-240G-U cannot be stacked with another ONT or with other equipment. The ONT mounting requirements are: b allow a minimum 100 mm clearance above the top cover allow a minimum 50 mm clearance from the side vents do not place any heat source directly above the top cover or below the bottom cover On a wall. i ii Slide the old ONT off of the mounting screws until the ONT is free of the wall. Install the replacement ONT following the wall mounting instructions for an I-240G-R or I-240G-U indoor ONT (DLP 122). 4 Connect the SC/APC fiber optic cable (DLP 125). Warning Be careful to maintain a bend radius of no less than 1.5 inches (3.8 cm) when connecting the fiber optic cable. Too small of a bend radius in the cable can result in damage to the optic fiber. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November 2013 NTP FE AAAA TCZZA Edition 01

227 NTP 182 Replace an I-240G-R or I-240G-U indoor ONT 5 If required, have approved service personnel who are trained to work with optic fiber clean the fiber optic connection. See DLP 134 for more information about fiber optic handling, inspection, and cleaning. Danger Fiber optic cables transmit invisible laser light. To avoid eye damage or blindness, never look directly into fibers, connectors, or adapters. 6 Verify that the power cable terminates with an 8-pin connector as shown in Figure NTP and described in Table NTP Figure NTP 182-2: 8-pin connector Pin 8 Pin5 Pin 4 Pin Table NTP 182-1: Pin assignments on the 8-pin connector Pin # Definition Pin # Definition 1 Power input (+ 12V) 5 12 V power return 2 UPS status: On battery 6 Alarm ground 3 UPS status: Battery missing 7 UPS status: Replace battery 4 GNC / Optional frame ground 8 UPS status: Low battery 7 Connect the power cable to the power connector on the ONT. Note Observe the following: Units must be powered by a Listed or CE approved and marked limited power source power supply with a minimum output rate of 12 V dc, 1.25 A. 8 Connect the POTS cables to the RJ-11 ports (DLP 123). 9 Connect the Ethernet cables to the RJ-45 ports (DLP 101). 10 If used, configure the SLID (chapter 6). Note A new SLID or the old SLID may be used with the replacement ONT. If a new SLID is used, the new SLID must also be programmed at the P-OLT using TL1 or a network manager. If the old SLID is used, no changes need to be made at the P-OLT; see the operations and maintenance documentation for the OLT for more details. 11 Verify the ONT LEDs, voltage status, and optical signal levels (DLP 127). NTP November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

228 NTP 182 Replace an I-240G-R or I-240G-U indoor ONT 12 Activate and test the services (DLP 128). 13 If necessary, reset the ONT (DLP 126). 14 STOP. This procedure is complete. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November 2013 NTP FE AAAA TCZZA Edition 01

229 NTP 182 Replace an I-240G-R or I-240G-U indoor ONT NTP November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

230 NTP 183 Configure an I-240G-R or I-240G-U indoor ONT General Please refer to the OLT Operations and Maintenance using TL1 and CLI guide for the software configuration procedure for I-240G-R or I-240G-U indoor ONTs. For HTTP configuration procedures, please refer to chapter 6, ONT management using an ONT interface. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November 2013 NTP FE AAAA TCZZA Edition 01

231 NTP 183 Configure an I-240G-R or I-240G-U indoor ONT NTP November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

232 I-240W-A 36 I-240W-A unit data sheet NTP 184 Install an I-240W-A indoor ONT NTP 185 Replace an I-240W-A indoor ONT NTP 186 Configure an I-240W-A indoor ONT Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

233 November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

234 36 I-240W-A unit data sheet 36.1 I-240W-A part numbers and identification I-240W-A general description I-240W-A software and installation feature support I-240W-A interfaces and interface capacity I-240W-A LEDs I-240W-A detailed specifications I-240W-A GEM ports and T-CONTs I-240W-A power support I-240W-A functional blocks I-240W-A standards compliance I-240W-A special considerations Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

235 36 I-240W-A unit data sheet 36.1 I-240W-A part numbers and identification Table 36-1 provides part numbers and identification information for I-240W-A indoor ONT. Table 36-1 Identification of I-240W-A indoor ONTs Mnemonic Ordering kit part number Provisioning part number Description CLEI CPR ECI/ Bar code I-240W-A 3FE AA customer-specific 3FE AB 2 POTS ports, 4 10/100/1000 Base-T Ethernet interfaces, and mw Wi-Fi radio with on/off switch. This ONT also has 2 USB ports. 3FE AA 3FE AB 2 POTS ports, 4 10/100/1000 Base-T Ethernet interfaces, and mw Wi-Fi radio with on/off switch. This ONT also has 2 USB ports. Includes 3-pin desktop European (EU) AC/DC adaptor. 3FE AB 2 POTS ports, 4 10/100/1000 Base-T Ethernet interfaces, and mw Wi-Fi radio with on/off switch. This ONT also has 2 USB ports. Includes 2-pin wall-mounted European (EU) AC/DC adaptor. 3FE BA 2 POTS ports, 4 10/100/1000 Base-T Ethernet interfaces, and mw Wi-Fi radio with on/off switch. This ONT also has 2 USB ports. Includes ac/dc power cord with Australian (AU) plug. 3FE CA 2 POTS ports, 4 10/100/1000 Base-T Ethernet interfaces, and mw Wi-Fi radio with on/off switch. This ONT also has 2 USB ports. Includes 3-pin wall-mounted British (UK) AC/DC adaptor. 3FE DA customer specific 2 POTS ports, 4 10/100/1000 Base-T Ethernet interfaces, and mw Wi-Fi radio with on/off switch. This ONT also has 2 USB ports. Includes 3-pin wall-mounted US AC/DC adaptor and RJ-11, RJ45, and SC/APC cables. (1 of 2) 36-2 November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

236 36 I-240W-A unit data sheet Mnemonic Ordering kit part number Provisioning part number Description CLEI CPR ECI/ Bar code I-240W-A (cont d) (2 of 2) 3FE DB 3FE AB 2 POTS ports, 4 10/100/1000 Base-T Ethernet interfaces, and mw Wi-Fi radio with on/off switch. This ONT also has 2 USB ports. Includes 3-pin wall-mounted US AC/DC adaptor. 3FE EA 2 POTS ports, 4 10/100/1000 Base-T Ethernet interfaces, and mw Wi-Fi radio with on/off switch. This ONT also has 2 USB ports. Includes 3-pin wall-mounted British (UK) AC/DC adaptor I-240W-A general description I-240W-A indoor ONTs provide the subscriber interface for the network by terminating the PON interface and converting it to user interfaces that directly connect to subscriber devices. The ONT is compatible with all existing subscriber equipment, including analog phones with both tone and rotary dial capabilities, cordless phones, modems, fax machines, and caller ID boxes (Type I, Type II, and Type III). I-240W-A indoor ONTs provide the following functions: Single fiber GPON interface with 1.244Gbit/s upstream and 2.488Gbit/s downstream data rates Advanced data features such as VLAN tag manipulation, classification, and filtering. Traffic classification and QoS capability Analog Telephone Adapter (ATA) function integrated based on SIP (RFC3261), with various CLASS services supported, including Caller ID, Call Waiting, Call Forwarding, and Call Transfer 5 REN per line Multiple voice Codec MDI/MDIX auto-negotiation Line Rate L2 traffic Internal Switch UPnP IGD1.0 support Bridged mode or routed mode per LAN port Internal DHCP server, with configurable DHCP pool and gateway WPS on wireless authorization support Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

237 36 I-240W-A unit data sheet 36.3 I-240W-A software and installation feature support Table 36-2 provides a list of software-based features and installation information supported by I-240W-A indoor ONTs. Table 36-2 I-240W-A indoor ONT software feature support Feature Chapter/description Click link for more information General ONT and MDU overview Service interface specifications General information common to multiple devices and an explanation of general system behaviors. ONT and MDU general and interface technical specifications ONT and MDU overview Ethernet interface specifications POTS interface specifications Services supported See the appropriate P-OLT user documentation for service creation procedures and descriptions. RSSI Wi-Fi specifications Optical budget Location and installation options ONT and MDU general and interface technical specifications ONT and MDU general and interface technical specifications ONT and MDU general and interface technical specifications How to install and replace an I-240W-A indoor ONT RSSI specifications Wi-Fi specifications ONT optical budget Install an I-240W-A indoor ONT Replace an I-240W-A indoor ONT Activation methods ONT and MDU overview SLID entry via Ethernet port HTTP management Statistics and performance monitoring Supported UPS configurations Information necessary to manage an ONT at a local site using an HTTP interface, CLI interface, CLI interface, or butt set. ONT and MDU statistics and performance monitoring Part numbers, ordering, and deployment configuration overview ONT management using an ONT interface Contact your Alcatel-Lucent representative ONT and MDU to UPS or power adapter compatibility support 36.4 I-240W-A interfaces and interface capacity Table 36-3 describes the supported interfaces and interface capacity for I-240W-A indoor ONTs November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

238 36 I-240W-A unit data sheet Table 36-3 I-240W-A indoor ONT interface connection capacity ONT type and model Maximum capacity POTS 10/ 100 BASE-T 10/ 100/ 1000 BASE-T RF video (CATV) MoCA VDSL2 E1/T1 Local craft GPON SC/ APC I-240W-A (1) Note (1) The I-240W-A ONTs provide Wi-Fi service that is enabled and disabled using a Wi-Fi on/off switch. I-240W-A connections and components Figure 36-1and 36-2 show the physical connections for I-240W-A indoor ONTs, Figure 36-1 I-240W-A indoor ONT physical connections (back view) OPTICAL Fiber optic port POTS port (RJ-11) TEL1 TEL2 POWER ON/OFF LAN1 LAN2 LAN3 LAN4 Ethernet ports (RJ45) Power input Power button Figure 36-2 I-240W-A indoor ONT physical connections (side view) USB 1 USB 2 LED WPS WLAN RESET USB port WPS button WLAN button Reset button Table 36-4 describes the physical connections for I-240W-A indoor ONTs. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

239 36 I-240W-A unit data sheet Table 36-4 I-240W-A indoor ONT physical connections Connection (1) Ethernet ports Fiber optic LED button POTS Wireless button WPS button Power USB ports Description This connection is provided through Ethernet RJ-45 connectors. Up to four 10/100 Base-T Ethernet interfaces are supported.the Ethernet ports can support both data and in-band video services on all four interfaces. This connection is provided through an SC/APC fiber optic connector. This buttons turns all LEDs on or off. This connection is provided through RJ-11 ports. Up to two POTS connections are supported.the POTS ports support voice services. Wi-Fi service is compliant with IEEE standards and is enabled and disabled using a Wireless button. The Wi-Fi Protected Setup button is labelled WPS. This button enables and disables WLAN data encryption. This connection is provided through the power connector. A power cable fitted with a barrel connector is used to make the connection. This connection is provided through 2 USB ports. Note (1) The primary path for the earth ground for these ONTs is provided by the 12V Return signal in the power connector I-240W-A LEDs Figure 36-3 shows the I-240W-A indoor ONT LEDs. Figure 36-3 I-240W-A indoor ONT LEDs POWER LINK AUTH LAN1 LAN2 LAN3 LAN4 TEL1 TEL2 VoIP WPS WLAN USB INTERNET Table 36-5 provides LED descriptions for I-240W-A indoor ONTs November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

240 36 I-240W-A unit data sheet Table 36-5 I-240W-A indoor ONT LEDs Indicator LED color and behavior LED behavior description PWR Link Auth LAN 1 to 4 TEL 1 to 2 VOIP WPS WLAN USB INTERNET Green solid Off Green solid Off Green solid Off Green solid Off Green solid Green flashing Off Green solid Off Green solid Red Off Green solid Green flashing Off Green solid Green flashing Off Green solid Off Operating on AC power No power source GPON link is OK GPON link is not OK ONT is authorized ONT is not authorized Ethernet is linked ONT power off or Ethernet not connected Off hook Call in On hook VOIP is OK VOIP is not OK "In Progress" or "Success" status "Error" and "Session Overlap" status WPS not activated Wireless enabled Traffic on wireless interface Wireless disabled One or more USB device is connected One or more USB device is connected with traffic No USB device connected HSI WAN is connected HSI WAN is not connected 36.6 I-240W-A detailed specifications Table 36-6 lists the physical specifications for I-240W-A indoor ONTs. Table 36-6 I-240W-A indoor ONT physical specifications Description Length Width Height Weight [within ± 0.5 lb (0.23 kg)] Specification 8.07 in. (205 mm) 6.94 in. (176.3 mm) 1.54 in. (39 mm) 0.79 lb (0.36 kg) Table 36-7 lists the power consumption specifications for I-240W-A indoor ONTs. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

241 36 I-240W-A unit data sheet Table 36-7 I-240W-A indoor ONT power consumption specifications Mnemonic Maximum power (Not to exceed) Condition Minimum power Condition I-240W-A (3FE AB) I-240W-A (3FE AB) 24 W 2 POTS off-hook, 4 10/100/1000 Base-T Ethernet, Wi-Fi operational 18 W 2 POTS off-hook, 4 10/100/1000 Base-T Ethernet, Wi-Fi operational 5.1 W 2 POTS on-hook, other interfaces/services not provisioned 5.9 W 2 POTS on-hook, other interfaces/services not provisioned Table 36-8 lists the environmental specifications for I-240W-A indoor ONTs. Table 36-8 I-240W-A indoor ONT environmental specifications Mounting method Temperature range and humidity Altitude On desk or wall mounted Operating: 23 F to 113 F (-5 C to 45 C) ambient temperature 10% to 90% relative humidity, non-condensing Storage: Contact your Alcatel-Lucent support representative for more information Contact your Alcatel-Lucent technical support representative for more information 36.7 I-240W-A GEM ports and T-CONTs Table 36-9 lists the maximum number of supported T-CONTs and GEM ports. See the appropriate release Customer Release Notes for the most accurate list of supported devices. Table 36-9 I-240W-A indoor ONT capacity for GEM ports and T-CONTs ONT or MDU Release Maximum Notes Package L ONTs GEM ports per indoor or outdoor ONT T-CONTs per indoor or outdoor ONT ONT R ONT R ONT R2.0 8 ONT R I-240W-A power support For the I-240W-A indoor ONT, contact your Alcatel-Lucent technical support representative for more information November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

242 36 I-240W-A unit data sheet 36.9 I-240W-A functional blocks I-240W-A indoor ONTs are single-residence ONTs that support Wireless (Wi-Fi) service. Wi-Fi service on these ONTs are compliant with the IEEE standard and enabled or disabled using a WLAN button. In addition to the Wi-Fi service, these ONTs transmit Ethernet packets to four RJ-45 Ethernet ports and voice traffic to two RJ-11 POTS ports. These ONTs also feature fiber optic, USB, and power connectors. Figure 36-4 shows the functional blocks for I-240W-A indoor ONT. Figure 36-4 Single-residence Wi-Fi ONT with Gigabit Ethernet and POTS and without RF video RJ-11 Power adapter Power POTS (2) GPON Optical block SOC Giganit Ethernet (4) Wi-Fi USB Wi-Fi RJ ONT SoC technology serves as the main hardware block for these ONTs; see Figure Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

243 36 I-240W-A unit data sheet Figure 36-5 I-240W-A ONT hardware block POTS ports Control processor SoC DSP SoC Bridge Ethernet MACs GPON MAC Ethernet ports GPON ONT SoC technology consists of five key elements: GPON MAC The Gigabit Passive Optical Network Media Access Control (GPON MAC) element on the SoC terminates the GPON interface using an optical diplexer. This interface supports GPON as described in G (GPON TC Layer) ITU specification. Ethernet MAC The SoC provides up to four GE MACs. DSP interface The Digital Signal Processor (DSP) provides voice processing for 2 POTS lines with 3-way calling. The DSP has a dedicated 64 kbyte instruction cache and shares a 32 kbyte data cache with the Control Processor. It provides up to 4 network processor cores, each at 800MHz. Control Processor The Control Processor features an integral memory management unit that supports a dedicated 64 kbyte instruction cache and shares a single 32 kbyte data cache with the DSP. The Control Processor and DSP also include a single channel Data Management Application (DMA) controller with a 4 kbyte read ahead low-latency Dynamic Random Access Memory (DRAM) access port. The processors typically run at 500 MHz. Switch matrix The Switch matrix provides an integrated data channel between the four GE MACs, the GPON MAC, the DSP, the control processor, and the other integrated elements such as flash memory, DRAM, and the local bus controller. These ONTs can also interact with additional hardware components to support functionality not provided by the SoC technology November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

244 36 I-240W-A unit data sheet I-240W-A standards compliance I-240W-A indoor ONTs are compliant with the following standards: 802.1p marking and VLAN based pbit is supported G.711 support for FAX and modem connection G.984 support GPON interface (framing) G support for Amd1, class B+ G support for activation and password functions G support for AES with operator enable/disable on per port-id level G support for FEC in both upstream and downstream directions G support for multicast using a single GEM Port-ID for all video traffic G984.4 and G support for OMCI interface for ONT management and provisioning I-240W-A special considerations Wi-Fi service I-240W-A indoor ONTs feature Wi-Fi service as well as voice and data services. Wi-Fi is a wireless networking technology that uses radio waves to provide wireless HSI and network connections. This ONT complies with the IEEE standards, which the Wi-Fi Alliance defines as the basis for Wi-Fi technology. Wi-Fi physical features I-240W-A indoor ONTs have the following physical features that assist in providing Wi-Fi service: WLAN button for enabling and disabling Wi-Fi service two external multi-directional antennae Wi-Fi Protected Setup (WPS) push button for adding WPS-enabled wireless devices Wi-Fi standards and certifications The Wi-Fi service on I-240W-A indoor ONTs supports the following IEEE standards and Wi-Fi Alliance certifications: compliant with IEEE standards certified for IEEE b/g/n standards WPA support including WPA-PSK certified for WPA2-Personal and WPA2-Enterprise Wi-Fi GUI features I-240W-A indoor ONTs have HTML-based Wi-Fi configuration GUIs. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

245 36 I-240W-A unit data sheet Procedure 36-1 Login to web-based GUI 1 Open a web browser and enter the IP address of the ONT in the address bar. The login window appears. The default gateway IP address is You can also obtain the IP address using DHCP after connecting your PC to the layer 3 UNI. 2 Enter your username and password in the Log in window. The default username is default while the default password is printed on the back of the ONT. Caution If you reset the router to recover the default username and password, all other router configuration settings will also be restored to their factory default values. Note If you forget the current username and password, press the reset button for 5 s and the default values for the username and password will be recovered at startup. 3 Click Login. 4 STOP. This procedure is complete November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

246 NTP 184 Install an I-240W-A indoor ONT Purpose This NTP provides the steps to install an I-240W-A indoor ONT. General The DLPs listed in this NTP describe mounting and cabling for I-240W-A indoor ONTs. Prerequisites See the listed DLPs for prerequisites. Recommended tools You need the following tools for the installation: #2 Phillips screwdriver 1/4 in. (6 mm) flat blade screwdriver wire strippers fiber optic splicing tools RJ-45 cable plug crimp tool voltmeter or multimeter optical power meter drill and drill bits Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November 2013 NTP FE AAAA TCZZA Edition 01

247 NTP 184 Install an I-240W-A indoor ONT Safety information Read the following safety information before installing the unit. Danger 1 Contact the local utility company before you connect the enclosure to the utilities. Danger 2 Observe the local and national laws and regulations that may be applicable to this installation. Warning This equipment is ESD sensitive. Proper ESD protections should be used when removing the fiber access cover of the indoor ONT. Caution Keep indoor ONTs out of direct sunlight. Prolonged exposure to direct sunlight can damage the unit. Procedure Note Observe the following: The indoor ONT should be installed in accordance with the applicable requirements of the NEC or CEC. Local authorities and practices take precedent when there is conflict between the local standard and the NEC or CEC. The indoor ONT must be installed by qualified service personnel. Indoor ONTs must be installed with cables that are suitably rated and listed for indoor use. See the detailed specifications in the I-240W-A unit data sheet for the temperature ranges for these ONTs. Use this procedure to install an I-240W-A indoor ONT. 1 Prepare the cables at the site where the ONT will be installed (DLP 100). 2 Are any of the cables missing? a If yes, go to step 3. b If no, go to step 4. 3 Locate each missing cable and route them to the ONT as per local practices. NTP November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

248 NTP 184 Install an I-240W-A indoor ONT 4 Place the indoor ONT unit: a On the flat surface, such as a desk. Note The I-240W-A cannot be stacked with another ONT or with other equipment. The ONT mounting requirements are: allow a minimum 100 mm clearance above the top cover allow a minimum 50 mm clearance from the side vents do not place any heat source directly above the top cover or below the bottom cover b On a wall (DLP 122). 5 Review the connection locations as shown in Figure NTP and NTP for the I-240W-A indoor ONT. Figure NTP 184-1: I-240W-A indoor ONT connections (back view) OPTICAL Fiber optic port POTS port (RJ-11) TEL1 TEL2 POWER ON/OFF LAN1 LAN2 LAN3 LAN4 Ethernet ports (RJ45) Power input Power button Figure NTP 184-2: I-240W-A indoor ONT connections (side view) USB 1 USB 2 LED WPS WLAN RESET USB port WPS button WLAN button Reset button Connect the Ethernet cables to the RJ-45 ports (DLP 101). 7 Connect the POTS cables to the RJ-11 ports (DLP 123). Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November 2013 NTP FE AAAA TCZZA Edition 01

249 NTP 184 Install an I-240W-A indoor ONT 8 Connect the SC/APC fiber optic cable (DLP 125). Warning Be careful to maintain a bend radius of no less than 1.5 inches (3.8 cm) when connecting the fiber optic cable. Too small of a bend radius in the cable can result in damage to the optic fiber. 9 Install the power supply according to manufacturer specifications. Note Observe the following: Units must be powered by a Listed or CE approved and marked limited power source power supply with a minimum output rate of 12 V dc, 1.25 A. 10 Connect the power cable to the power connector. 11 Power up the ONT unit by using the power switch. 12 If used, enable the Wi-Fi service (DLP 130). 13 Verify the ONT LEDs, voltage status, and optical signal levels (DLP 127). 14 Activate and test the services (DLP 128). 15 If used, configure the SLID (DLP 129). 16 If necessary, reset the ONT (DLP 126). 17 STOP. This procedure is complete. NTP November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

250 NTP 185 Replace an I-240W-A indoor ONT Purpose This NTP provides the steps to replace I-240W-A indoor ONTs. General The DLPs listed in this NTP describe mounting and cabling for I-240W-A indoor ONTs. Prerequisites See the listed DLPs for prerequisites. Recommended tools You need the following tools for replacing the ONT: #2 Phillips screwdriver 1/4 in. (6 mm) flat blade screwdriver wire strippers fiber optic splicing tools RJ-45 cable plug crimp tool voltmeter or multimeter optical power meter drill and drill bits Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November 2013 NTP FE AAAA TCZZA Edition 01

251 NTP 185 Replace an I-240W-A indoor ONT Safety information Read the following safety information before replacing the unit. Danger 1 Contact the local utility company before you connect the enclosure to the utilities. Danger 2 Observe the local and national laws and regulations that may be applicable to this installation. Warning This equipment is ESD sensitive. Proper ESD protections should be used when removing the fiber access cover of the indoor ONT. Caution Keep indoor ONTs out of direct sunlight. Prolonged exposure to direct sunlight can damage the unit. Procedure Note Observe the following: The indoor ONT should be installed in accordance with the applicable requirements of the NEC or CEC. Local authorities and practices take precedent when there is conflict between the local standard and the NEC or CEC. The indoor ONT must be installed by qualified service personnel. Indoor ONTs must be installed with cables that are suitably rated and listed for indoor use. See the detailed specifications in the I-240W-A unit data sheet for the ONT temperature ranges for these ONTs. Use this procedure to replace an I-240W-A indoor ONT. 1 Deactivate the ONT services (DLP 131). If you are using the SLID feature, this step is not required. The ONT and the services can remain in service (IS). 2 If used, disable the Wi-Fi service (DLP 130). 3 Power down the unit by using the on/off power switch. 4 Disconnect the POTS, Ethernet, and power cables (DLP 132) as well as fiber optic cables (DLP 133) from the ONT; see Figures NTP and NTP for the connector locations on the I-240W-A indoor ONT. NTP November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

252 NTP 185 Replace an I-240W-A indoor ONT Figure NTP 185-1: I-240W-A indoor ONT connections (back view) OPTICAL Fiber optic port POTS port (RJ-11) TEL1 TEL2 POWER ON/OFF LAN1 LAN2 LAN3 LAN4 Ethernet ports (RJ45) Power input Power button Figure NTP 185-2: I-240W-A indoor ONT connections (side view) USB 1 USB 2 LED WPS WLAN RESET USB port WPS button WLAN button Reset button Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November 2013 NTP FE AAAA TCZZA Edition 01

253 NTP 185 Replace an I-240W-A indoor ONT 5 Replace the ONT with a new unit: a On a flat surface, such as a desk. i Substitute the new ONT for the old ONT on a flat surface, horizontally resting on its four feet. Note The I-240W-A cannot be stacked with another ONT or with other equipment. The ONT mounting requirements are: allow a minimum 100 mm clearance above the top cover allow a minimum 50 mm clearance from the side vents do not place any heat source directly above the top cover or below the bottom cover ii Go to step 6. b On a wall. i ii Slide the old ONT off of the mounting screws until the ONT is free of the wall. Slide the wall mount holes on the ONT enclosure over the mounting screws until it is securely seated. 6 Connect the Ethernet cables to the RJ-45 ports (DLP 101). 7 Connect the POTS cables to the RJ-11 ports (DLP 123). 8 If required, have approved service personnel who are trained to work with optic fiber clean the fiber optic connection. See DLP 134 for more information about fiber optic handling, inspection, and cleaning. Danger Fiber optic cables transmit invisible laser light. To avoid eye damage or blindness, never look directly into fibers, connectors, or adapters. 9 Connect the SC/APC fiber optic cable (DLP 125). Warning Be careful to maintain a bend radius of no less than 1.5 inches (3.8 cm) when connecting the fiber optic cable. Too small of a bend radius in the cable can result in damage to the optic fiber. 10 Install the power supply according to manufacturer specifications. Note Observe the following: Units must be powered by a Listed or CE approved and marked limited power source power supply with a minimum output rate of 12 V dc, 1.25 A. 11 Connect the power cable to the power connector. 12 Power up the unit by using the power switch. NTP November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

254 NTP 185 Replace an I-240W-A indoor ONT 13 If used, enable the Wi-Fi service (DLP 130). 14 If used, configure the SLID (DLP 129). Note A new SLID or the old SLID may be used with the replacement ONT. If a new SLID is used, the new SLID must also be programmed at the P-OLT using TL1 or a network manager. If the old SLID is used, no changes need to be made at the P-OLT; see the operations and maintenance documentation for the OLT for more details. 15 Verify the ONT LEDs, voltage status, and optical signal levels (DLP 127). 16 Activate and test the services (DLP 128). 17 If necessary, reset the ONT (DLP 126). 18 STOP. This procedure is complete. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November 2013 NTP FE AAAA TCZZA Edition 01

255 NTP 185 Replace an I-240W-A indoor ONT NTP November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

256 NTP 186 Configure an I-240W-A indoor ONT General Please refer to the OLT Operations and Maintenance using TL1 and CLI guide for the software configuration procedure for I-240W-A indoor ONT. For HTTP configuration procedures, please refer to chapter 6, ONT management using an ONT interface. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November 2013 NTP FE AAAA TCZZA Edition 01

257 NTP 186 Configure an I-240W-A indoor ONT NTP November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

258 I-240W-B 37 I-240W-B unit data sheet NTP 187 Install an I-240W-B indoor ONT NTP 188 Replace an I-240W-B indoor ONT NTP 189 Configure an I-240W-B indoor ONT Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

259 November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

260 37 I-240W-B unit data sheet 37.1 I-240W-B part numbers and identification I-240W-B general description I-240W-B software and installation feature support I-240W-B interfaces and interface capacity I-240W-B LEDs I-240W-B detailed specifications I-240W-B GEM ports and T-CONTs I-240W-B power support I-240W-B functional blocks I-240W-B standards compliance I-240W-B special considerations Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

261 37 I-240W-B unit data sheet 37.1 I-240W-B part numbers and identification Table 37-1 provides part numbers and identification information for I-240W-B indoor ONT. Table 37-1 I-240W-B part numbers and identification Mnemonic Ordering kit part number Provisioning part number Description CLEI CPR ECI/ Bar code I-240W-B 3FE CA 3FE CA 2 POTS ports, 4 Ethernet 10/100 Base-T interfaces, and 1 Wi-Fi radio on/off switch I-240W-B general description I-240W-B indoor ONTs provide the subscriber interface for the network by terminating the PON interface and converting it to user interfaces that directly connect to subscriber devices. The ONT is compatible with all existing subscriber equipment, including analog phones with both tone and rotary dial capabilities, cordless phones, modems, fax machines, and caller ID boxes (Type I, Type II, and Type III). I-240W-B indoor ONTs provide the following functions: Single fiber GPON interface with 1.244Gbit/s upstream and 2.488Gbit/s downstream data rates Advanced data features such as VLAN tag manipulation, classification, and filtering. Traffic classification and QoS capability Analog Telephone Adapter (ATA) function integrated based on SIP (RFC3261), with various CLASS services supported, including Caller ID, Call Waiting, Call Forwarding, and Call Transfer 5 REN per line Multiple voice Codec 37.3 I-240W-B software and installation feature support Table 37-2 provides a list of software-based features and installation information supported by I-240W-B indoor ONTs November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

262 37 I-240W-B unit data sheet Table 37-2 I-240W-B indoor ONT software feature support Feature Chapter/description Click link for more information General ONT and MDU overview Service interface specifications General information common to multiple devices and an explanation of general system behaviors. ONT and MDU general and interface technical specifications ONT and MDU overview Ethernet interface specifications POTS interface specifications Services supported See the appropriate P-OLT user documentation for service creation procedures and descriptions. RSSI Wi-Fi specifications Optical budget Location and installation options ONT and MDU general and interface technical specifications ONT and MDU general and interface technical specifications ONT and MDU general and interface technical specifications How to install and replace an I-240W-B indoor ONT RSSI specifications Wi-Fi specifications ONT optical budget Install an I-240W-B indoor ONT Replace an I-240W-B indoor ONT Activation methods ONT and MDU overview SLID entry via Ethernet port HTTP management Statistics and performance monitoring Supported UPS configurations Information necessary to manage an ONT at a local site using an HTTP interface, CLI interface, CLI interface, or butt set. ONT and MDU statistics and performance monitoring Part numbers, ordering, and deployment configuration overview ONT management using an ONT interface Performance monitoring statistics for Package N ONTs ONT and MDU to UPS or power adapter compatibility support 37.4 I-240W-B interfaces and interface capacity Table 37-3 describes the supported interfaces and interface capacity for I-240W-B indoor ONTs. Table 37-3 I-240W-B indoor ONT interface connection capacity ONT type and model Maximum capacity POTS 10/ 100 BASE-T 10/ 100/ 1000 BASE-T RF video (CATV) MoCA VDSL2 E1/T1 Local craft GPON SC/ APC I-240W-B (1) Note (1) The I-240W-B ONTs provide Wi-Fi service that is enabled and disabled using a Wi-Fi on/off switch. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

263 37 I-240W-B unit data sheet I-240W-B connections and components Figure 37-1and 37-2 show the physical connections for I-240W-B indoor ONTs, Figure 37-1 I-240W-B indoor ONT physical connections (back view) WLAN RESET WPS OPTIC Fiber optic connector LAN1 LAN2 LAN3 LAN4 USB POTS1 POTS2 POWER Ethernet interface USB interface POTS interface Power connection Power button Figure 37-2 I-240W-B indoor ONT physical connections (side view) WLAN RESET WPS WLAN RESET WPS Table 37-4 describes the physical connections for I-240W-B indoor ONTs. Table 37-4 I-240W-B indoor ONT physical connections Connection (1) Ethernet ports POTS WLAN button WPS button Description This connection is provided through Ethernet RJ-45 connectors. Up to four 10/100 Base-T Ethernet interfaces are supported.the Ethernet ports can support both data and in-band video services on all four interfaces. This connection is provided through RJ-11 ports. Up to two POTS connections are supported.the POTS ports support voice services. Wi-Fi service is compliant with IEEE standards and is enabled and disabled using a Wi-Fi on/off switch. The Wi-Fi Protected Setup button is labelled WPS. This button enables and disables WLAN data encryption. (1 of 2) 37-4 November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

264 Power GPON Link Optical LAN1 LAN2 LAN3 LAN4 VOIP1 VOIP2 WLAN WIPS USB 37 I-240W-B unit data sheet Connection (1) Power Fiber optic USB ports Description This connection is provided through the power connector. A power cable fitted with a barrel connector is used to make the connection. This connection is provided through an SC/APC fiber optic connector. This connection is provided through a USB port. (2 of 2) Note (1) The primary path for the earth ground for these ONTs is provided by the 12V Return signal in the power connector I-240W-B LEDs Figure 37-3 shows the I-240W-B indoor ONT LEDs. Figure 37-3 I-240W-B indoor ONT LEDs LAN VOIP Power GPON Link Optical WLAN WPS USB WLAN RESET WPS Table 37-5 provides LED descriptions for I-240W-B indoor ONTs. Table 37-5 I-240W-B indoor ONT LEDs Indicator LED color and behavior LED behavior description PWR GPON Link Optical (1 of 2) Green solid Off Green solid Green flashing Off Red flashing Off Operating on AC power No power source ONT activated and registered with OLT ONT is ranging and synchronizing ONT has not begun activation Received optical power is less than optics sensitivity Received optical power is OK Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

265 37 I-240W-B unit data sheet Indicator LED color and behavior LED behavior description LAN 1 to 4 VOIP 1 to 2 WLAN WPS USB (2 of 2) Green solid Green flashing Off Green solid Green flashing Off Green solid Green flashing Off Green solid Green flashing (slow) Green flashing (fast) Off Green solid Green flashing Off Ethernet is linked but no service traffic Ethernet is linked with service traffic ONT power off or Ethernet not connected Registered to the soft switch but no service traffic POTS line is linked with service traffic ONT power off or VoIP service not registered Wireless enabled Traffic on wireless interface Wireless disabled Connection successful under protection set In negotiation under protection set Negotiation failed under protection set Connection failed under protection set or WPS not activated USB device connected without traffic USB device connected with traffic No USB device connected 37.6 I-240W-B detailed specifications Table 37-6 lists the physical specifications for I-240W-B indoor ONTs. Table 37-6 I-240W-B indoor ONT physical specifications Description Length Width Height Weight [within ± 0.5 lb (0.23 kg)] Specification 8.19 in. (208 mm) 6.65 in. (169 mm) 1.34 in. (34 mm) 0.86 lb (0.39 kg) Table 37-7 lists the power consumption specifications for I-240W-B indoor ONTs. Table 37-7 I-240W-B indoor ONT power consumption specifications Mnemonic Maximum power (Not to exceed) Condition Minimum power Condition I-240W-B 17.6 W 2 POTS off-hook, 4 10/100 Base-T Ethernet, Wi-Fi operational 3.1 W 2 POTS on-hook, other interfaces/services not provisioned Table 37-8 lists the environmental specifications for I-240W-B indoor ONTs November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

266 37 I-240W-B unit data sheet Table 37-8 I-240W-B indoor ONT environmental specifications Mounting method Temperature range and humidity Altitude On desk Operating: 23 F to 113 F (-5 C to 45 C) ambient temperature 5% to 90% relative humidity, non-condensing Storage: Contact your Alcatel-Lucent support representative for more information Contact your Alcatel-Lucent technical support representative for more information 37.7 I-240W-B GEM ports and T-CONTs Table 37-9 lists the maximum number of supported T-CONTs and GEM ports. See the appropriate release Customer Release Notes for the most accurate list of supported devices. Table 37-9 I-240W-B indoor ONT capacity for GEM ports and T-CONTs ONT or MDU Release Maximum Notes Package N ONTs GEM ports per indoor or outdoor ONT T-CONTs per indoor or outdoor ONT ONT R ONT R I-240W-B power support For the I-240W-B indoor ONT, contact your Alcatel-Lucent technical support representative for more information I-240W-B functional blocks I-240W-B indoor ONTs are single-residence ONTs that support Wireless (Wi-Fi) service. Wi-Fi service on these ONTs are compliant with the IEEE standard and enabled or disabled using a Wi-Fi on/off switch. In addition to the Wi-Fi service, these ONTs transmit Ethernet packets to four RJ-45 Ethernet ports and voice traffic to two RJ-11 POTS ports. These ONTs also feature fiber optic, USB, and power connectors. Figure 37-4 shows the functional blocks for I-240W-B indoor ONT. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

267 37 I-240W-B unit data sheet Figure 37-4 Single-residence Wi-Fi ONT with Gigabit Ethernet and POTS and without RF video RJ-11 Power adapter Power POTS (2) GPON Optical block SOC Fast Ethernet PHY (4) Wi-Fi USB Wi-Fi RJ ONT SoC technology serves as the main hardware block for these ONTs; see Figure Figure 37-5 I-240W-B ONT hardware block POTS ports Control processor SoC DSP SoC Bridge Ethernet MACs GPON MAC Ethernet ports GPON ONT SoC technology consists of five key elements: GPON MAC The Gigabit Passive Optical Network Media Access Control (GPON MAC) element on the SoC terminates the GPON interface using an optical diplexer. This interface supports GPON as described in G (GPON TC Layer) ITU specification November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

268 37 I-240W-B unit data sheet Ethernet MAC The SoC provides up to four GE MACs. DSP interface The Digital Signal Processor (DSP) provides voice processing for 2 POTS lines with 3-way calling. The DSP has a dedicated 64 kbyte instruction cache and shares a 32 kbyte data cache with the Control Processor. Control Processor The Control Processor features an integral memory management unit that supports a dedicated 64 kbyte instruction cache and shares a single 32 kbyte data cache with the DSP. The Control Processor and DSP also include a single channel Data Management Application (DMA) controller with a 4 kbyte read ahead low-latency Dynamic Random Access Memory (DRAM) access port. The processors typically run at 400 MHz. Switch matrix The Switch matrix provides an integrated data channel between the four GE MACs, the GPON MAC, the DSP, the control processor, and the other integrated elements such as flash memory, DRAM, and the local bus controller. These ONTs can also interact with additional hardware components to support functionality not provided by the SoC technology I-240W-B standards compliance I-240W-B indoor ONTs are compliant with the following standards: 802.1p support for mapping and mapper service profile on U/S 802.1p support for marking and remarking 802.1p support for Class of Service based on VLAN-ID b support for maximum transmit power (EIRP) equal to or greater than 200 mw (19 dbm) n support for maximum transmit power (EIRP) equal to or greater than 100 mw (19 dbm) g/n support for processing that does not degrade the committed LAN-LAN and/or LAN-WAN throughput rate G.711 support for FAX, modem connection, and TTY devices G support for activation and password functions G support for AES with operator enable/disable on per port-id level G support for FEC in both upstream and downstream directions G support for multicast using a single GEM Port-ID for all video traffic G984.4 and G support for OMCI interface for ONT management and provisioning Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

269 37 I-240W-B unit data sheet I-240W-B special considerations Wi-Fi service I-240W-B indoor ONTs feature Wi-Fi service as well as voice and data services. Wi-Fi is a wireless networking technology that uses radio waves to provide wireless HSI and network connections. This ONT complies with the IEEE standards, which the Wi-Fi Alliance defines as the basis for Wi-Fi technology. Wi-Fi physical features I-240W-B indoor ONTs have the following physical features that assist in providing Wi-Fi service: on/off radio switch for enabling and disabling Wi-Fi service two external multi-directional antennae Wi-Fi Protected Setup (WPS) push button, with indicator LED, for adding WPS-enabled wireless devices Wi-Fi standards and certifications The Wi-Fi service on I-240W-B indoor ONTs supports the following IEEE standards and Wi-Fi Alliance certifications: compliant with IEEE standards certified for IEEE b/g/n standards WPA support including WPA-PSK certified for WPA2-Personal certified for WMM and WMM scheduled access certified for WPS as an AP type device with registrar support Wi-Fi GUI features I-240W-B indoor ONTs have HTML-based Wi-Fi configuration GUIs containing the following features: configuration of the best available channel to a fixed value selection of the LAN devices allowed to access the ONT through a wireless interface (for example, MAC address filtering) operational status indicators for numerous data elements entry of Wi-Fi device WPS PIN codes disabling of the broadcasting of the primary user SSID (default broadcasting must be enabled) user scheduling of the enabling and disabling of the Wi-Fi connection November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

270 37 I-240W-B unit data sheet Web-based ONT configuration and reporting I-240W-B indoor ONTs support limited configuration using a web-based GUI. Using the GUI, you can configure or view information for the following options: device status network security application management diagnostics Procedure 37-1 Login to web-based GUI 1 Open a web browser and enter the IP address of the ONT in the address bar. The login window appears. The default gateway IP address is You can also obtain the IP address using DHCP after connecting your PC to the layer 3 UNI. 2 Enter your username and password in the Log in window. The default username and password are printed on the label on the back of the ONT. Caution If you reset the router to recover the default username and password, all other router configuration settings will also be restored to their factory default values. Note If you forget the current username and password, press the reset button for 5 s and the default values for the username and password will be recovered at startup. 3 Click Log in. 4 STOP. This procedure is complete. Procedure 37-2 General status information retrieval 1 Select Status from the top menu in the GPON Web-Management System window. 2 Select the Device Info option from the Status menu. The Status -> Device Information window appears; see Figure Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

271 37 I-240W-B unit data sheet Figure 37-6 Device information window Table describes the fields in the Device Information window. Table Device Information parameters Field Device Name Serial Number Hardware Version Software Version Description A string identifying the name of the device. A string identifying the unique serial number of the device. A string identifying the particular hardware version. A string identifying the current software version. 3 STOP. This procedure is complete. Procedure 37-3 WAN information retrieval 1 Select Status from the top menu in the GPON Web-Management System window. 2 Select the WAN Info option from the Status menu. The Status -> WAN Information -> IPv4 Link Information window appears; see Figure November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

272 37 I-240W-B unit data sheet Figure 37-7 WAN IPv4 Link Information window Table describes the fields in the WAN IPv4 Link Information window. Table WAN IPv4 Link Information parameters Field Default Gateway Subnet Mask Preferred DNS Server Alternate DNS Server Description IP address of the node on the network that is chosen as default when the IP address does not match any other routes in the routing table Subnet mask of the WAN interface IP Address of the first DNS server IP Address of the second DNS server 3 Select the IPv6 Link Info option from the left-hand menu. The Status -> WAN Information -> IPv6 Link Information window appears; see Figure Figure 37-8 WAN IPv6 Link Information window Table describes the fields in the WAN IPv6 Link Information window. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

273 37 I-240W-B unit data sheet Table WAN IPv6 Link Information parameters Field Default IPv6 Gateway Preferred IPv6 DNS Server Alternate IPv6 DNS Server IPv6 Connection Description IP address of the node on the network that is chosen as default when the IP address does not match any other routes in the routing table when IPv6 is used IP address of the first IPv6 DNS server IP address of the second IPv6 DNS server Details existing IPv6 connection(s) 4 Select the GPON Link Info option from the left-hand menu. The Status -> WAN Information -> GPON Link Information window appears; see Figure Figure 37-9 WAN GPON Link Information window Table describes the fields in the WAN GPON Link Information window November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

274 37 I-240W-B unit data sheet Table WAN GPON Link Information parameters Field Description GPON Link Information Connection Status LOID Register Status FEC Ability FEC Mode Status of the WAN connection Logical ID authentication status Whether FEC is supported Whether FEC is enabled or disabled GPON Tx/Rx Packets Status Receive Bytes Send Bytes Receive Packets Send Packets Receive Multicast Packets Send Multicast Packets Receive Broadcast Packets Send Broadcast Packets Receive OMCI Packets Send OMCI Packets FEC Error HEC Error Drop Packets Number of bytes of information sent on the WAN connection Number of bytes of information received on the WAN connection Number of packets sent on the WAN connection Number of packets received on the WAN connection Number of multicast packets sent on the WAN connection Number of multicast packets received on the WAN connection Number of broadcast packets sent on the WAN connection Number of broadcast packets received on the WAN connection Number of OMCI packets sent on the WAN connection Number of OMCI packets received on the WAN connection Number of FEC errors Number of HEC errors Number of dropped packets on the WAN connection Warning Information Light Signal Mode Status of optical module Optical Module Information Receive Power Send Power Receive power (in dbm) Send power (in dbm) 5 STOP. This procedure is complete. Procedure 37-4 User information retrieval 1 Select Status from the top menu in the GPON Web-Management System window. 2 Select the User Info option from the Status menu. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

275 37 I-240W-B unit data sheet The Status -> User Information -> WLAN Information window appears; see Figure Figure User WLAN Information window Table describes the fields in the User WLAN Information window. Table User WLAN Information parameters Field Description WLAN Interface Information WLAN Connection Status Channel SSID-1 Name SSID-1 Authentication and Encryption Whether WLAN connection is enabled or disabled Channel Name of the SSID-1 Type of authentication and encryption used on SSID-1 Tx/Rx Packets Status Interface Number of bytes, packets, errors, and dropped packets on the interface 3 Select the Ethernet Info option from the left-hand menu. The Status -> User Information -> Ethernet Information window appears; see Figure November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

276 37 I-240W-B unit data sheet Figure User Ethernet Information window Table describes the fields in the User Ethernet Information window. Table User Ethernet Information parameters Field Description Network Information IP Address: LAN Side IPv4 address IP Address: LAN Side IPv6 address MAC address IP address of the LAN-side IPv4 server IP address of the LAN-side IPv6 server Network MAC address Tx/Rx Packets Status Interface Number of bytes, packets, errors, and dropped packets on the interface Ethernet device information IP Address MAC address Address source Status IP Address of the Ethernet device MAC address of the Ethernet device The way to obtain an IP address - DHCP or static IP Whether the Ethernet device is connected. 4 Select the USB Info option from the left-hand menu. The Status -> User Information -> USB Information window appears; see Figure Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

277 37 I-240W-B unit data sheet Figure User USB Information window The User USB Information window indicates whether anything is connected to the USB port. 5 STOP. This procedure is complete. Procedure 37-5 Voice information retrieval 1 Select Status from the top menu in the GPON Web-Management System window. 2 Select the Voice Info option from the Status menu. The Status -> Voice Information -> Voice Configuration Information window appears; see Figure Figure Voice Configuration Information window Table describes the fields in the Voice Configuration Information window November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

278 37 I-240W-B unit data sheet Table Voice Configuration Information parameters Field Description SIP Setting Proxy Server Registrar Server Outbound Proxy Server Standby Proxy Server Standby Registrar Server Standby Outbound Proxy Server User agent domain IP address, port, and protocol of the proxy server IP address, port, and protocol of the registrar server IP address and port of the outbound proxy server IP address, port, and protocol of the standby proxy server IP address, port, and protocol of the standby registrar server IP address and port of the standby outbound proxy server Port and protocol of the user agent domain Coding ability Support dial-up plan Support signaling protocol Support heartbeat Whether a dial-up plan is supported The supported signaling protocol: H.248 or SIP Whether heartbeat is supported Codec list EntryID Codec Packetization Period Integer that identifies the entry Supported Codec Assigned packetization period by the specified codec, in milliseconds 3 Select the Line Status option from the left-hand menu. The Status -> Voice Information -> Line Status window appears; see Figure Figure Voice Line Status window Table describes the fields in the Voice Line Status window. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

279 37 I-240W-B unit data sheet Table Voice Line Status parameters Field Line ID Status Telephone Number Codec setting Description Integer that identifies the voice line Enabled or disabled Telephone number Codec settings 4 STOP. This procedure is complete. Procedure 37-6 Remote status information retrieval 1 Select Status from the top menu in the GPON Web-Management System window. 2 Select the Remote Status option from the Status menu. The Status -> Remote Status -> ITMS Connecting window appears; see Figure Figure Remote ITMS Connecting window Table describes the fields in the Remote ITMS Connecting window. Table Remote ITMS Connecting parameters Field Inform Report ITMS Connection Request Description Mechanism that allows HGU to inform a corresponding ACS of various conditions Mechanism for the ACS to issue a Connection Request to HGU at any time 3 Select the ITMS Distributing option from the left-hand menu November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

280 37 I-240W-B unit data sheet The Status -> Remote Status -> ITMS Distributing window appears; see Figure Figure Remote ITMS Distributing window Table describes the fields in the Remote ITMS Distributing window. Table Remote ITMS Distributing parameters Field The Latest Remote Business Configuration Status Description Status of ACS provision services to HGU recently, for example: Configuration Success or Configuration failed. 4 STOP. This procedure is complete. Network configuration using the web-based GUI The following procedures provide the steps for configuring the network settings for the WAN, LAN, WLAN, Remote, QoS, Time, and Route. Procedure 37-7 Network WAN configuration 1 Select Network from the top menu in the GPON Web-Management System window. 2 Select the WAN Settings option from the Network menu. The Network -> WAN Settings -> Internet Link window appears; see Figure Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

281 37 I-240W-B unit data sheet Figure WAN Settings window 3 Configure the WAN parameters as described in Table Table WAN parameters Field Connection Name Status Connection mode IP Mode Enable NAT MTU Enable DHCP server Enable VLAN Description WAN connection name Enable or disable Choose bridged or routed Choose IPv4, IPv6, or IPV4V6 from the drop-down menu. Choose DHCP, Static, or PPPoE by clicking the appropriate radio button. Click on the checkbox to enable NAT Maximum Transmission Unit Click on the checkbox to enable the DHCP server Click on the checkbox to enable VLAN VLAN ID Value of VLAN, from 2 to p Value of 802.1p Service bind LAN Port binding SSID Port binding Port VLAN bindings Choose service type for this WAN Choose LAN port to bind on this WAN Choose Wi-Fi port to bind on this WAN Choose port on which to do VLAN binding 4 Click on Save/Enable to save your changes and enable WAN. 5 STOP. This procedure is complete November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

282 37 I-240W-B unit data sheet Procedure 37-8 Network LAN configuration 1 Select Network from the top menu in the GPON Web-Management System window. 2 Select the LAN Settings option from the Network menu. The Network -> LAN Settings -> IPv4 Setting window appears; see Figure Figure LAN IPv4 Settings window 3 Configure the LAN IPv4 parameters as described in Table Table LAN IPv4 parameters Field IPv6 Address Subnet Mask DHCP Server DHCP Start IP Address DHCP End IP Address Subnet Mask DHCP Lease Time Description IP address of the LAN interface in dotted-decimal format. For example, a sample IP address is Subnet mask of the IP addresses in your LAN. The default is Select either the Enable or Disable radio button. If enabled, the ONT assigns IP addresses, an IP default gateway, and DNS servers to computers that support the DHCP client; for example, Windows 95, Windows NT. Starting IP address of the DHCP IP pool Ending IP address of the DHCP IP pool DHCP subnet mask Number of minutes of client lease time. A zero means one day of lease time Device Address Range Configuration Device Type DHCP Start IP Address DHCP End IP Address Click the checkbox for each type of supported device: computer, STB, phone, or camera Starting IP address of the DHCP IP pool Ending IP address of the DHCP IP pool Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

283 37 I-240W-B unit data sheet 4 Click on Save/Apply to save your changes and apply them to the LAN. 5 Select the IPv6 Setting from the left-hand menu. The Network -> LAN Settings -> IPv6 Setting window appears; see Figure Figure LAN IPv6 Settings window 6 Configure the LAN IPv6 parameters as described in Table Table LAN IPv6 parameters Field DHCPv6 Server Enable DHCPv6 Server IP Address Pool Enable DHCP Start IP Address DHCP End IP Address SLAAC Enable Stateful IP Address Configuration Stateful Others Configuration Maximum interval for periodic RA messages Minimum interval for periodic RA messages Description Click the checkbox to enable the DHCPv6 server Click the checkbox to enable DHCPv6 server IP address pool Starting IP address of the DHCP IP pool Ending IP address of the DHCP IP pool Click the checkbox to enable SLAAC Click the checkbox to enable Stateful IP address configuration Check the checkbox to enable Stateful Others configuration Maximum interval for periodic RA messages Minimum interval for periodic RA messages 7 Click on Save to save your changes and apply them to the LAN. 8 STOP. This procedure is complete November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

284 37 I-240W-B unit data sheet Procedure 37-9 Network WLAN configuration 1 Select Network from the top menu in the GPON Web-Management System window. 2 Select the WLAN Settings option from the Network menu. The Network -> WLAN Settings -> Basic Setting window appears; see Figure Figure WLAN Basic Settings window 3 Configure the WLAN basic parameters as described in Table Table WLAN basic parameters Field Enable Wifi SSID Select Enable SSID Hidden Hotspot SSID BSSID Description Click the checkbox to enable the Wi-Fi Choose which SSID to configure Click the checkbox to enable the SSID Click the checkbox to hide the SSID during AP scans Enter the SSID BSSID Band Choose a band from the drop-down menu: 2.4G Channel Choose channel 1 to 13 or Auto from the drop-down menu Mode Choose b/g/n mixed,802.11b/g,802.11g or b from the drop-down menu Bandwidth Control Sideband Guard Interval Choose 20MHz,40Mhz or 20/40MHz auto from the drop-down menu Choose up sideband or down sideband from the drop-down menu Choose 800ns or 400ns from the drop-down menu n Rate Choose 0:Auto, 1:6.5Mbps, 2:13Mbps, 3:19.5Mbps, 4:26Mbps, 5:39Mbps, 6:52Mbps, 7:58.5Mbps, 8:65Mbps, 9:13Mbps, 10:26Mbps, 11:39Mbps, 12:52Mbps, 13:78Mbps, 14:104Mbps, 15:117Mbps or 16:130Mbps from the drop-down menu (1 of 2) Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

285 37 I-240W-B unit data sheet Field b/g Rate Transmission Power WMM Wi-Fi Multimedia Description Choose 0:Auto, 1:6.5Mbps, 2:13Mbps, 3:19.5Mbps, 4:26Mbps, 5:39Mbps, 6:52Mbps, 7:58.5Mbps, 8:65Mbps, 9:13Mbps, 10:26Mbps, 11:39Mbps, 12:52Mbps, 13:78Mbps, 14:104Mbps, 15:117Mbps or 16:130Mbps from the drop-down menu Choose 100%, 80%, 60%, 40% or 20% from the drop-down menu Choose Enable or Disable from the drop-down menu (2 of 2) 4 Click Save/Apply to save your changes. 5 Select the Security Setting link from the left-hand menu. The Network -> WLAN Settings -> Security Setting window appears; see Figure Figure WLAN Security Settings window 6 Configure the WLAN security parameters as described in Table Table WLAN security parameters Field Description Wireless settings Security SSID Select SSID Network Authentication Method WPA Pre-Shared Key Key Display WPA Updated Session Key Interval Select the SSID Displays the associated SSID Choose Open, Share, WPA-PSK, WPA2-PSK, or Mixed WPA2/WPA-PSK from the drop-down menu Enter the pre-share key Click this checkbox to display the WPA pre-shared key Enter the WPA Update Session Key Interval (1 of 2) November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

286 37 I-240W-B unit data sheet Field WAN Connection Description Choose AES or TKIP from the drop-down menu WPS PIN Connect PIN Enter the PIN (2 of 2) 7 Click Save/Apply to save your changes in the Wireless security settings or press Connect to connect to the wireless network. 8 STOP. This procedure is complete. Procedure Network remote configuration 1 Select Network from the top menu in the GPON Web-Management System window. 2 Select the Remote option from the Network menu. The Network -> Remote -> TR-069 Setting window appears; see Figure Figure Remote TR-069 Settings window 3 Configure the Remote TR-069 parameters as described in Table Table Remote TR-069 parameters Field Inform Inform Interval ACS URL ACS Username Description Select the Disabled or Enabled radio button Set the interval duration Enter the URL for the TR-069 Auto Configuration Server Enter the username for the TR-069 Auto Configuration Server (1 of 2) Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

287 37 I-240W-B unit data sheet Field ACS Password Connection Request URL Connection Request Username Connection Request Password Description Enter the password for the TR-069 Auto Configuration Server URL for the TR-069 connection Enter your TR-069 connection username Enter your TR-069 connection password (2 of 2) 4 Click Save/Apply to save your changes. 5 Select the LOID Config link from the left-hand menu. The Network -> Remote -> LOID Config window appears; see Figure Figure Remote LOID Configuration window 6 Configure the remote LOID configuration parameters as described in Table Table Remote LOID Configuration parameters Field LOID Password Description Enter the LOID, do not exceed 24 characters Enter the password 7 Click Save/Apply to save your changes in the Wireless security settings or press Connect to connect to the wireless network. 8 STOP. This procedure is complete November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

288 37 I-240W-B unit data sheet Procedure Network QoS configuration 1 Select Network from the top menu in the GPON Web-Management System window. 2 Select the QoS Config option from the Network menu. The Network -> QoS Config window appears; see Figure Figure QoS Configuration window 3 Configure the QoS parameters as described in Table Table QoS parameters Field Enable QoS Bandwidth Enable CAR Schedule Policy Rule Template Enable DSCP Marking Enable 802.1p Marking Description Click the checkbox to enable QoS Enter the bandwidth (in bps) Click the checkbox to enable CAR Choose the PQ or WRR radio button Choose a rule template from the drop-down menu Click the checkbox to enable DSCP marking Click the checkbox to enable 802.1p marking Queue Queue Priority Lists QoS queues Lists queue priorities App App Queue Lists applications Lists queue associated with each application Classifications Queue clsf type (Min) value QoS queue CLSF type Minimum value (1 of 2) Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

289 37 I-240W-B unit data sheet Field Max value Protocol DSCP mark value Description Maximum value Protocols DSCP mark value 802.1p mark value 802.1p mark value (2 of 2) 4 Click Edit to edit a specific application or classification table entry. 5 Click Apply to save your changes. 6 STOP. This procedure is complete. Procedure Network Time configuration 1 Select Network from the top menu in the GPON Web-Management System window. 2 Select the Time option from the Network menu. The Network -> Time window appears; see Figure Figure Time window 3 Set the time. a Set the time manually. i ii Enter a time in the Current System Time field. Click Set Time November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

290 37 I-240W-B unit data sheet b Set the time using an Internet time server. i ii Click Get Time. Click Set Time. c Automatically synchronize the system time with an Internet time server by selecting the Automatically synchronize with an Internet time server checkbox. 4 Click Save/Apply to save your changes. 5 STOP. This procedure is complete. Procedure Network route configuration 1 Select Network from the top menu in the GPON Web-Management System window. 2 Select the Route option from the Network menu. The Network -> Route -> IPv4 Static Route window appears; see Figure Figure IPv4 Static Route window 3 For each hop in the route, enter the following information: Destination IP Address Subnet Mask Length Gateway Interface 4 Click Submit to save your changes. 5 STOP. This procedure is complete. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

291 37 I-240W-B unit data sheet Security configuration using the web-based GUI The following procedures provide the steps for performing security configuration including the setting up of URL, MAC, and port filters and firewalls. Procedure Security URL filter configuration 1 Select Security from the top menu in the GPON Web-Management System window. 2 Select the URL Filter option from the Security menu. The Security -> URL Filter window appears; see Figure Figure Security URL filter window 3 Enable a URL filter by clicking the Enable URL filter checkbox. 4 Choose whether your filter will block or allow the listed URLs. 5 For each URL to be added to the URL list, enter the URL Address and port and then click Add Filter. 6 STOP. This procedure is complete. Procedure Security firewall configuration 1 Select Security from the top menu in the GPON Web-Management System window. 2 Select the Firewall option from the Security menu. The Security -> Firewall -> Security Level window appears; see Figure November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

292 37 I-240W-B unit data sheet Figure Security firewall security level window 3 Select the security level of the firewall from the drop-down menu. 4 Click Add/Apply. 5 Select the DoS Setting link from the left-hand menu. The Security -> Firewall -> DoS setting window appears; see Figure Figure Security firewall DoS settings window 6 Enable or disable DoS protection by choosing the appropriate radio button. 7 Click Add/Apply. 8 STOP. This procedure is complete. Procedure Security MAC filter configuration 1 Select Security from the top menu in the GPON Web-Management System window. 2 Select the MAC Filter option from the Security menu. The Security -> MAC Filter window appears; see Figure Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

293 37 I-240W-B unit data sheet Figure Security MAC filter window 3 Enable or disable a MAC filter by choosing the appropriate radio button. 4 Choose whether your filter will block or allow the listed MAC addresses by choosing the appropriate radio button. 5 For each MAC address to be added to the list, enter the MAC Address and then click Add Filter. 6 STOP. This procedure is complete. Procedure Security Port filter configuration 1 Select Security from the top menu in the GPON Web-Management System window. 2 Select the Port Filter option from the Security menu. The Security -> Port Filter window appears; see Figure Figure Security Port filter window November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

294 37 I-240W-B unit data sheet 3 Enable or disable an IP filter by choosing the appropriate radio button. 4 Choose whether your filter will block or allow the listed IP addresses by choosing the appropriate radio button. 5 For each IP address to be added to the list, enter the IP Address and then click Add Filter. 6 STOP. This procedure is complete. Application configuration using the web-based GUI The following procedures provide the steps for performing application configuration including the setting up of DDNS, advanced NAT, UpnP, IGMP, MLD, voice, and scheduled tasks. Procedure DDNS configuration 1 Select Application from the top menu in the GPON Web-Management System window. 2 Select the DDNS Config option from the Application menu. The Application -> DDNS Config window appears; see Figure Figure DDNS configuration window 3 Add a DNS server by entering the following information: Service provider Domain Interface Username Password Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

295 37 I-240W-B unit data sheet 4 Enable the DDNS. a b Select the Enable checkbox in the Add DDNS panel before pressing submit. Select the Enable checkbox in the DDNS table and then press Save. 5 Click Submit. 6 STOP. This procedure is complete. Procedure Advanced NAT configuration 1 Select Application from the top menu in the GPON Web-Management System window. 2 Select the Advanced NAT option from the Application menu. The Application -> Advanced NAT -> ALG Config window appears; see Figure Figure Advanced NAT ALG configuration window 3 Choose which ALGs to enable by clicking the appropriate checkboxes. 4 Click Save. 5 Select the DMZ Config link from the left-hand menu. The Application -> Advanced NAT -> DMZ Config window appears; see Figure November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

296 37 I-240W-B unit data sheet Figure Advanced NAT DMZ configuration window 6 Enable DMZ by clicking the checkbox. 7 Click Save. 8 Select the Host Virtual Config link from the left-hand menu. The Application -> Advanced NAT -> Host Virtual Config window appears; see Figure Figure Advanced NAT host virtual configuration window 9 Add a virtual server by entering: Any Interface External start port External end port Protocol Internal start port Internal end port Server IP Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

297 37 I-240W-B unit data sheet 10 Click Add. 11 STOP. This procedure is complete. Procedure UPnP configuration 1 Select Application from the top menu in the GPON Web-Management System window. 2 Select the UPnP Setting option from the Application menu. The Application -> UPnP Setting window appears; see Figure Figure UPnP window 3 Enable UPnP by clicking the checkbox. 4 Click Save/Apply. 5 STOP. This procedure is complete. Procedure IGMP configuration 1 Select Application from the top menu in the GPON Web-Management System window. 2 Select the IGMP Setting option from the Application menu. The Application -> IGMP Setting -> IGMP Snooping window appears; see Figure November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

298 37 I-240W-B unit data sheet Figure IGMP snooping window 3 Enable or disable IGMP snooping by choosing the appropriate radio button. 4 Click Save/Apply. 5 Select the IGMP Proxy option from the left-hand menu. The Application -> IGMP Setting -> IGMP Proxy window appears; see Figure Figure IGMP proxy window 6 Enable or disable the IGMP proxy by choosing the appropriate radio button. 7 Click Add/Apply. 8 STOP. This procedure is complete. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

299 37 I-240W-B unit data sheet Procedure MLD configuration 1 Select Application from the top menu in the GPON Web-Management System window. 2 Select the MLD Setting option from the Network menu. The Application -> MLD Setting -> MLD Snooping window appears; see Figure Figure MLD snooping window 3 Enable or disable MLD snooping by choosing the appropriate radio button. 4 Click Save/Apply. 5 Select the MLD Proxy option from the left-hand menu. The Application -> MLD Setting -> MLD Proxy window appears; see Figure Figure MLD proxy window 6 Enable or disable the MLD proxy by choosing the appropriate radio button November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

300 37 I-240W-B unit data sheet 7 Click Add/Apply. 8 STOP. This procedure is complete. Procedure Voice configuration 1 Select Application from the top menu in the GPON Web-Management System window. 2 Select the Voice option from the Application menu. The Application -> Voice -> Voice Config window appears; see Figure Figure Voice configuration window 3 Configure the Voice parameters as described in Table Table Voice parameters Field Description Voice Voice protocol DTMF transfer mode CLIP mode Flashhook detecting time range Hanging reminder timer Busy tone time (second) No answer tone time (second) Codec Negotiation Rule Fax mode Voice services use signaling protocol, such as H.248 or SIP Method by which DTMF digits must be passed, for example, InBand, or RFC2833 Only supports FSK Flashhook event detection time range in milliseconds Duration of the hanging reminder tone played by the ONT, in seconds Duration of busy tone played by the ONT, in seconds Duration of ringback tone played by the ONT, in seconds Choose remote first or local first Choose G711 or T38 (1 of 2) Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

301 37 I-240W-B unit data sheet Field Fax negotiation mode Enable synchronization telephone time Enable polarity revert charging Description Choose control by SIP server or auto-switch by ONT. Provides telephone time which can be synchronized with an NTP server Enable or disable polarity revert charging SIP Setting Proxy Server Registrar Server Outbound Proxy Standby Proxy Server Standby Registrar Server Standby Outbound Proxy Home Gateway Domain Signal DSCP RTP DSCP Enable Heartbeat Heartbeat Cycle (second) Heartbeat Count Heartbeat Method Register Period (second) Register Retry Interval (second) Session Refresh Interval (minute) Minimum Session Refresh Interval (minute) Configure IP address or host name, destination port, and transport protocol for connecting to the SIP server Configure IP address or host name, destination port, and transport protocol for connecting to the SIP registrar server Configure IP address or host name, destination port, and transport protocol for connecting to the outbound proxy Configure IP address or host name, destination port, and transport protocol for connecting to the standby SIP server Configure IP address or host name, destination port, and transport protocol for connecting to the standby SIP registrar server Configure IP address or host name, destination port, and transport protocol for connecting to the standby outbound proxy ONT domain, local port and transport protocol Diffserv code point to be used for outgoing SIP signaling packets, from 0 to 63 Diffserv code point to be used for outgoing RTP packets, from 0 to 63 Enable heartbeat between SIP server with ONT Heartbeat cycle in seconds Heartbeat time-out counts Choose active or passive Period over which ONT must periodically register, in seconds Register retry interval, in seconds Session refresh timer, in minutes Minimum session refresh timer, in minutes (2 of 2) 4 Click Save. 5 Select the DigitMap Config option from the left-hand menu. The Application -> Voice -> DigitMap Config window appears; see Figure November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

302 37 I-240W-B unit data sheet Figure Voice DigitMap configuration window 6 Configure the Voice DigitMap parameters as described in Table Table Voice DigitMap parameters Field Enable dialplan Dialplan DigitMap match mode Start Digit Timer (second) Interdigit Short Timer (second) Interdigit Long Timer (second) Description Click the checkbox to enable a dialplan Digit map controlling the transmission of dialed digit information. The maximum length is Choose minimum match or maximum match Maximum allowable time, in seconds, before receiving first dialed digit. This timer is restarted by off-hook. Minimum allowable time, in seconds, between the dialing of digits. This timer is restarted every time a digit is dialed. Maximum allowable time, in seconds, between the dialing of digits. This timer is restarted every time a digit is dialed. Expiration of this timer indicates "End of Dialing". 7 Click Save. 8 Select the Line Setting option from the left-hand menu. The Application -> Voice -> Line Setting window appears; see Figure Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

303 37 I-240W-B unit data sheet Figure Voice line settings window 9 Configure the voice line parameters as described in Table Table Voice line parameters Field Description Line Setting Line Enable Status Authenticate Username Authenticate Password Telephone Number Codec Setting Transmit Gain (db) Receive Gain (db) Connection Status Enable Echo Cancellation Echo Cancellation Tail Select line Enable or disable this line Indicates current status of this line Username used to authenticate the connection to the server Password used to authenticate the connection to the server Telephone number the ONT will use to identify this line Set of codecs enabled for use with this line Gain, in db, to apply to the transmitted voice signal prior to encoding Gain, in db, to apply to the received voice signal after decoding Indication of whether or not echo cancellation is currently in for this line Enable or disable echo cancellation for this line Tail length in milliseconds of the echo canceller associated with this line (whether or not it is currently in use) Physical Term ID Port Physical term ID of port Port1 Physical term ID of port 1 Port2 Physical term ID of port 2 10 Click Save. 11 Select the Supplementary option from the left-hand menu November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

304 37 I-240W-B unit data sheet The Application -> Voice -> Supplementary window appears; see Figure Figure Voice supplementary window 12 Configure the voice supplementary parameters as described in Table Table Voice supplementary parameters Field Supplement Service Mode Warmline Delay Timer (second) Line Enable Callwaiting Enable Conference Intelligence Public Telephone Access Code Warmline URI Description Choose the supplement service mode Warmline delay timer, in seconds Line Enable or disable call waiting Enable or disable conference Intelligence Public Telephone Access Code Warmline URI 13 Click Save. 14 Select the Voice Test option from the left-hand menu. The Application -> Voice -> Voice Test window appears; see Figure Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

305 37 I-240W-B unit data sheet Figure Voice test window 15 Configure the voice test parameters as described in Table Table Voice test parameters Field Description Voice Test Interface Selector Test State Connectivity Test Result Choose the interface Choose the selector Test state Connectivity test result IADDiagnostics Test Test Server Test State Register Result Reason Choose whether to test the primary server or standby server by choosing the appropriate radio button. Test state Register result Reason Voice IMS Subscription Line dial-tone-pattern mcid-service no-dialing-behaviour hold-service three-party-service conference-uri hotline-uri cw-service Choose the line to test dial-tone-pattern mcid-service no-dialing-behavior hold-service three-party-service conference-uri hotline-uri cw-service November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

306 37 I-240W-B unit data sheet 16 Click Start test to start the test or Query status to determine the status of a test. 17 STOP. This procedure is complete. Procedure Scheduled tasks configuration 1 Select Application from the top menu in the GPON Web-Management System window. 2 Select the Scheduled Tasks option from the Application menu. The Application -> Scheduled Tasks -> Home Storage window appears; see Figure Figure Scheduled tasks home storage window 3 Perform a USB download by entering the following information: Download directory User Name Password FTP Remote URL 4 Click Download. 5 Select the IPTV option from the left-hand menu. The Application -> Scheduled Tasks -> IPTV window appears; see Figure Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

307 37 I-240W-B unit data sheet Figure Scheduled tasks IPTV window 6 Enter the multicast VLAN for IPTV. 7 Click Save. 8 STOP. This procedure is complete. Management configuration using the web-based GUI The following procedures provide the steps for performing management configuration for users and devices, and configuring log files. Procedure User management 1 Select Management from the top menu in the GPON Web-Management System window. 2 Select the User Management option from the Management menu. The Management -> User Management window appears; see Figure Figure User management window November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

308 37 I-240W-B unit data sheet 3 Add a new user or change an existing user s username or password by entering the following information: User name New user name (leave blank if no change) New password Confirm password (must match password above) 4 Click Save. 5 STOP. This procedure is complete. Procedure Device management 1 Select Management from the top menu in the GPON Web-Management System window. 2 Select the Device Management option from the Management menu. The Management -> Device Management -> Device Reboot window appears; see Figure Figure Reboot window 3 Click Reboot to reboot the HGU. 4 Select the USB Backup link from the left-hand menu. The Management -> Device Management -> USB Backup window appears; see Figure Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

309 37 I-240W-B unit data sheet Figure USB backup window 5 Enable or disable fast recovery by choosing the appropriate radio button. 6 Enter the USB port on which to allow fast recovery. 7 Click Backup Config. 8 Select the Restore Default link from the left-hand menu. The Management -> Device Management -> Restore Default window appears; see Figure Figure Restore default window 9 Click on Click to restore default. 10 STOP. This procedure is complete. Procedure Log file management 1 Select Management from the top menu in the GPON Web-Management System window. 2 Select the Log File option from the Management menu November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

310 37 I-240W-B unit data sheet The Management -> Log File -> Log Level window appears; see Figure Figure Log level window 3 Enable or disable the log file by choosing the appropriate radio button. 4 Choose a log level for which items will be saved in the log file. 5 Choose a display level for which items will be displayed in the system log. 6 Click Save. 7 Select the System Log link from the left-hand menu to view the system log. The Management -> Log File -> System Log window appears; see Figure Figure System log window 8 Click Refresh log to refresh the system log view. 9 STOP. This procedure is complete. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

311 37 I-240W-B unit data sheet Procedure SLID Management 1 Select Management from the top menu in the GPON Web-Management System window. 2 Select the GPON Config option from the Management menu. The Management -> GPON Config window appears; see Figure Figure GPON Config window 3 The current SLID is shown. To change the SLID, enter the new SLID, choose the SLID mode from the drop-down menu and click on Save/Apply. Diagnostics configuration using the web-based GUI The following procedures provide the steps for performing diagnostics on the ONT. Procedure Ping 1 Select Diagnostics from the top menu in the GPON Web-Management System window. The Diagnostics -> PING Test window appears; see Figure November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

312 37 I-240W-B unit data sheet Figure Ping window 2 Choose the interface to use for the ping test. 3 Enter the Destination IP Address or Host Name. 4 Click Ping. 5 STOP. This procedure is complete. Procedure Trace route 1 Select Diagnostics from the top menu in the GPON Web-Management System window. 2 Choose the Trace Route link in the left-hand menu. The Diagnostics -> Trace Route window appears; see Figure Figure Trace route window 3 Choose the interface to use for the trace route test. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

313 37 I-240W-B unit data sheet 4 Enter the Destination IP Address or Host Name. 5 Click Trace Route. 6 STOP. This procedure is complete. Procedure Manual Inform Test 1 Select Diagnostics from the top menu in the GPON Web-Management System window. 2 Choose the Manually Inform link in the left-hand menu. The Diagnostics -> Manually Inform window appears; see Figure Figure Manually inform window 3 Click Manual Inform to perform the manual inform test. 4 STOP. This procedure is complete November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

314 NTP 187 Install an I-240W-B indoor ONT Purpose This NTP provides the steps to install an I-240W-B indoor ONT. General The DLPs listed in this NTP describe mounting and cabling for I-240W-B indoor ONTs. Prerequisites See the listed DLPs for prerequisites. Recommended tools You need the following tools for the installation: #2 Phillips screwdriver 1/4 in. (6 mm) flat blade screwdriver wire strippers fiber optic splicing tools RJ-45 cable plug crimp tool voltmeter or multimeter optical power meter drill and drill bits Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November 2013 NTP FE AAAA TCZZA Edition 01

315 NTP 187 Install an I-240W-B indoor ONT Safety information Read the following safety information before installing the unit. Danger 1 Contact the local utility company before you connect the enclosure to the utilities. Danger 2 Observe the local and national laws and regulations that may be applicable to this installation. Warning This equipment is ESD sensitive. Proper ESD protections should be used when removing the fiber access cover of the indoor ONT. Caution Keep indoor ONTs out of direct sunlight. Prolonged exposure to direct sunlight can damage the unit. Procedure Note Observe the following: The indoor ONT should be installed in accordance with the applicable requirements of the NEC or CEC. Local authorities and practices take precedent when there is conflict between the local standard and the NEC or CEC. The indoor ONT must be installed by qualified service personnel. Indoor ONTs must be installed with cables that are suitably rated and listed for indoor use. See the detailed specifications in the I-240W-B unit data sheet for the temperature ranges for these ONTs. Use this procedure to install an I-240W-B indoor ONT. 1 Prepare the cables at the site where the ONT will be installed (DLP 100). 2 Are any of the cables missing? a If yes, go to step 3. b If no, go to step 4. 3 Locate each missing cable and route them to the ONT as per local practices. NTP November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

316 NTP 187 Install an I-240W-B indoor ONT 4 Place the indoor ONT unit: a On the flat surface, such as a desk. Note The I-240W-B cannot be stacked with another ONT or with other equipment. The ONT mounting requirements are: allow a minimum 100 mm clearance above the top cover allow a minimum 50 mm clearance from the side vents do not place any heat source directly above the top cover or below the bottom cover b On a wall (DLP 122). 5 Review the connection locations as shown in Figure NTP and NTP for the I-240W-B indoor ONT. Figure NTP 187-1: I-240W-B indoor ONT connections (back view) WLAN RESET WPS OPTIC Fiber optic connector LAN1 LAN2 LAN3 LAN4 USB POTS1 POTS2 POWER Ethernet interface USB interface POTS interface Power connection Power button Figure NTP 187-2: I-240W-B indoor ONT (side view) WLAN RESET WPS WLAN RESET WPS Connect the Ethernet cables to the RJ-45 ports (DLP 101). 7 Connect the POTS cables to the RJ-11 ports (DLP 123). Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November 2013 NTP FE AAAA TCZZA Edition 01

317 NTP 187 Install an I-240W-B indoor ONT 8 Connect the SC/APC fiber optic cable (DLP 125). Warning Be careful to maintain a bend radius of no less than 1.5 inches (3.8 cm) when connecting the fiber optic cable. Too small of a bend radius in the cable can result in damage to the optic fiber. 9 Install the power supply according to manufacturer specifications. Note Observe the following: Units must be powered by a Listed or CE approved and marked limited power source power supply with a minimum output rate of 12 V dc, 1.25 A. 10 Connect the power cable to the power connector. 11 Power up the ONT unit by using the power switch. 12 If used, enable the Wi-Fi service (DLP 130). 13 Verify the ONT LEDs, voltage status, and optical signal levels (DLP 127). 14 Activate and test the services (DLP 128). 15 If used, configure the SLID (DLP 129). 16 If necessary, reset the ONT (DLP 126). 17 STOP. This procedure is complete. NTP November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

318 NTP 188 Replace an I-240W-B indoor ONT Purpose This NTP provides the steps to replace I-240W-B indoor ONTs. General The DLPs listed in this NTP describe mounting and cabling for I-240W-B indoor ONTs. Prerequisites See the listed DLPs for prerequisites. Recommended tools You need the following tools for replacing the ONT: #2 Phillips screwdriver 1/4 in. (6 mm) flat blade screwdriver wire strippers fiber optic splicing tools RJ-45 cable plug crimp tool voltmeter or multimeter optical power meter drill and drill bits Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November 2013 NTP FE AAAA TCZZA Edition 01

319 NTP 188 Replace an I-240W-B indoor ONT Safety information Read the following safety information before replacing the unit. Danger 1 Contact the local utility company before you connect the enclosure to the utilities. Danger 2 Observe the local and national laws and regulations that may be applicable to this installation. Warning This equipment is ESD sensitive. Proper ESD protections should be used when removing the fiber access cover of the indoor ONT. Caution Keep indoor ONTs out of direct sunlight. Prolonged exposure to direct sunlight can damage the unit. Procedure Note Observe the following: The indoor ONT should be installed in accordance with the applicable requirements of the NEC or CEC. Local authorities and practices take precedent when there is conflict between the local standard and the NEC or CEC. The indoor ONT must be installed by qualified service personnel. Indoor ONTs must be installed with cables that are suitably rated and listed for indoor use. See the detailed specifications in the I-240W-B unit data sheet for the ONT temperature ranges for these ONTs. Use this procedure to replace an I-240W-B indoor ONT. 1 Deactivate the ONT services (DLP 131). If you are using the SLID feature, this step is not required. The ONT and the services can remain in service (IS). 2 If used, disable the Wi-Fi service (DLP 130). 3 Power down the unit by using the on/off power switch. 4 Disconnect the POTS, Ethernet, and power cables (DLP 132) as well as fiber optic cables (DLP 133) from the ONT; see Figures NTP and NTP for the connector locations on the I-240W-B indoor ONT. NTP November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

320 NTP 188 Replace an I-240W-B indoor ONT Figure NTP 188-1: I-240W-B ONT connections (back view) WLAN RESET WPS OPTIC Fiber optic connector LAN1 LAN2 LAN3 LAN4 USB POTS1 POTS2 POWER Ethernet interface USB interface POTS interface Power connection Power button Figure NTP 188-2: I-240W-B ONT (side view) WLAN RESET WPS WLAN RESET WPS Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November 2013 NTP FE AAAA TCZZA Edition 01

321 NTP 188 Replace an I-240W-B indoor ONT 5 Replace the ONT with a new unit: a On a flat surface, such as a desk. i Substitute the new ONT for the old ONT on a flat surface, horizontally resting on its four feet. Note The I-240W-B cannot be stacked with another ONT or with other equipment. The ONT mounting requirements are: allow a minimum 100 mm clearance above the top cover allow a minimum 50 mm clearance from the side vents do not place any heat source directly above the top cover or below the bottom cover ii Go to step 6. b On a wall. i ii Slide the old ONT off of the mounting screws until the ONT is free of the wall. Slide the wall mount holes on the ONT enclosure over the mounting screws until it is securely seated. 6 Connect the Ethernet cables to the RJ-45 ports (DLP 101). 7 Connect the POTS cables to the RJ-11 ports (DLP 123). 8 If required, have approved service personnel who are trained to work with optic fiber clean the fiber optic connection. See DLP 134 for more information about fiber optic handling, inspection, and cleaning. Danger Fiber optic cables transmit invisible laser light. To avoid eye damage or blindness, never look directly into fibers, connectors, or adapters. 9 Connect the SC/APC fiber optic cable (DLP 125). Warning Be careful to maintain a bend radius of no less than 1.5 inches (3.8 cm) when connecting the fiber optic cable. Too small of a bend radius in the cable can result in damage to the optic fiber. 10 Install the power supply according to manufacturer specifications. Note Observe the following: Units must be powered by a Listed or CE approved and marked limited power source power supply with a minimum output rate of 12 V dc, 1.25 A. 11 Connect the power cable to the power connector. 12 Power up the unit by using the power switch. NTP November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

322 NTP 188 Replace an I-240W-B indoor ONT 13 If used, enable the Wi-Fi service (DLP 130). 14 If used, configure the SLID (DLP 129). Note A new SLID or the old SLID may be used with the replacement ONT. If a new SLID is used, the new SLID must also be programmed at the P-OLT using TL1 or a network manager. If the old SLID is used, no changes need to be made at the P-OLT; see the operations and maintenance documentation for the OLT for more details. 15 Verify the ONT LEDs, voltage status, and optical signal levels (DLP 127). 16 Activate and test the services (DLP 128). 17 If necessary, reset the ONT (DLP 126). 18 STOP. This procedure is complete. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November 2013 NTP FE AAAA TCZZA Edition 01

323 NTP 188 Replace an I-240W-B indoor ONT NTP November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

324 NTP 189 Configure an I-240W-B indoor ONT General Please refer to the OLT Operations and Maintenance using TL1 and CLI guide for the software configuration procedure for I-240W-B indoor ONT. For HTTP configuration procedures, please refer to chapter 6, ONT management using an ONT interface. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November 2013 NTP FE AAAA TCZZA Edition 01

325 NTP 189 Configure an I-240W-B indoor ONT NTP November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

326 I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P 38 I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P unit data sheet NTP 190 Install an I-240W-P, I-240W-Q, I-240W-R, I-240W-T, or I-241W-P indoor ONT NTP 191 Replace an I-240W-P, I-240W-Q, I-240W-R, I-240W-T, or I-241W-P indoor ONT NTP 192 Configure an I-240W-P, I-240W-Q, I-240W-R, I-240W-T, or I-241W-P indoor ONT Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

327 November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

328 38 I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P unit data sheet 38.1 I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P part numbers and identification I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P general description I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P software and installation feature support I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P interfaces and interface capacity I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P LEDs I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P detailed specifications I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P GEM ports and T-CONTs I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P power support I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P functional blocks Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

329 38 I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P unit data sheet I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P standards compliance I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P special considerations November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

330 38 I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P unit data sheet 38.1 I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P part numbers and identification Table 38-1 provides part numbers and identification information for I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P indoor ONT. Table 38-1 I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P part numbers and identification Mnemonic Ordering kit part number Provisioning part number Description CLEI CPR ECI/ Bar code I-240W-P 3FE AD 3FE AH 2 POTS ports, and 4 Ethernet 10/100/1000Base-T interfaces, and 1 Wi-Fi radio on/off switch. Includes ac/dc power cord with European variant plug and fiber storage tray. 3FE AN 3FE AP 3FE AU 2 POTS ports, and 4 Ethernet 10/100/1000 Base-T interfaces, and 1 Wi-Fi radio on/off switch. Includes ac/dc power cord with Australian variant plug and fiber storage tray. 2 POTS ports, and 4 Ethernet 10/100/1000 Base-T interfaces, and 1 Wi-Fi radio on/off switch. Includes ac/dc power cord with United Kingdom variant plug and fiber storage tray. 2 POTS ports, and 4 Ethernet 10/100/1000 Base-T interfaces, and 1 Wi-Fi radio on/off switch. Includes ac/dc power cord with United States variant plug and fiber storage tray. I-240W-Q 3FE AE 3FE BL 2 POTS ports, and 4 Ethernet 10/100/1000Base-T interfaces, and 1 Wi-Fi radio on/off switch. Includes ac/dc power cord with European (EU) variant plug and fiber storage tray. 3FE AQ 2 POTS ports, and 4 Ethernet 10/100/1000 Base-T interfaces, and 1 Wi-Fi radio on/off switch. Includes ac/dc power cord with Australian (AU) variant plug and fiber storage tray. 3FE AR 2 POTS ports, and 4 Ethernet 10/100/1000 Base-T interfaces, and 1 Wi-Fi radio on/off switch. Includes ac/dc power cord with United Kingdom (UK) variant plug and fiber storage tray. 3FE AY (customer-specific variant) 3FE AN 2 POTS ports, and 4 Ethernet 10/100/1000 Base-T interfaces, and 1 Wi-Fi radio on/off switch. Includes ac/dc power cord with United States (US) variant plug and fiber storage tray. (1 of 2) Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

331 38 I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P unit data sheet Mnemonic Ordering kit part number Provisioning part number Description CLEI CPR ECI/ Bar code I-240W-R 3FE AW (customerspecific variant) 2 POTS ports, and 4 Ethernet 10/100 Base-T interfaces, and 1 Wi-Fi radio on/off switch. Includes ac/dc power cord with China (CCC) variant plug and fiber storage tray. 3FE AX (customerspecific variant) 2 POTS ports, and 4 Ethernet 10/100 Base-T interfaces, and 1 Wi-Fi radio on/off switch. Includes ac/dc power cord with United States (US) variant plug and fiber storage tray. I-240W-T 3FE AB (customerspecific variant) 2 POTS ports, and 4 Ethernet 10/100/1000 Base-T interfaces, and Wi-Fi service. Includes ac/dc power cord with United States (US) variant plug and fiber storage tray. I-241W-P 3FE AA 3FE AG 2 POTS ports, 4 Gig E Ethernet 10/100/1000 Base-T interfaces, 1 RF video connector, and 1 Wi-Fi radio on/off switch. Includes ac/dc power cord with European variant plug and fiber storage tray. 3FE AG 3FE AH 2 POTS ports, 4 GigE Ethernet 10/100/1000 Base-T interfaces, 1 RF video connector, and 1 Wi-Fi radio on/off switch. Includes ac/dc power cord with Australian variant plug and fiber storage tray. 2 POTS ports, 4 GigE Ethernet 10/100/1000 Base-T interfaces, 1 RF video connector, and 1 Wi-Fi radio on/off switch. Includes ac/dc power cord with United Kingdom variant plug and fiber storage tray. (2 of 2) 38.2 I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P general description I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P indoor ONTs provide the subscriber interface for the network by terminating the PON interface and converting it to user interfaces that directly connect to subscriber devices. The ONT is compatible with all existing subscriber equipment, including analog phones with both tone and rotary dial capabilities, cordless phones, modems, fax machines, and caller ID boxes (Type I, Type II, and Type III). I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P indoor ONTs provide the following functions: ITU-T Wi-Fi interface to enable wireless access two types of video services: video overlay and IPTV/VoD (I-240W-Q, I-240W-R, and I-240W-T ONTs excepted) 38-4 November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

332 38 I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P unit data sheet video contents delivered in two forms as data: unicast or multicast (I-240W-Q, I-240W-R and I-240W-T ONTs) fully G.984 series GPON standard compliant multicast GEM port for IPTV services IGMPv3 (RFC 3376) or IGMPv2 (RFC 2236) snooping G984.4 and G standard compliant OMCI interface for ONT management and provisioning MIB manipulation over OMCI by Create, Delete, Set, Get, and Get next commands limited web-based end-user configuration remote software image download (as well as activation and reboot) over OMCI performance monitoring as well as alarms and AVC reports 38.3 I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P software and installation feature support Table 38-2 provides a list of software-based features and installation information supported by I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P indoor ONTs. Table 38-2 I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P indoor ONT software feature support Feature Chapter/description Click link for more information General ONT and MDU overview Service interface specifications General information common to multiple devices and an explanation of general system behaviors. ONT and MDU general and interface technical specifications ONT and MDU overview Ethernet interface specifications POTS interface specifications RF video interface specifications for video overlay (I-241W-P ONT only) Services supported See the appropriate P-OLT user documentation for service creation procedures and descriptions. RSSI Wi-Fi specifications Optical budget Location and installation options ONT and MDU general and interface technical specifications ONT and MDU general and interface technical specifications ONT and MDU general and interface technical specifications How to install and replace an I-241W-P indoor ONT RSSI specifications Wi-Fi specifications ONT optical budget Install an I-240W-P, I-240W-Q, I-240W-R, I-240W-T, or I-241W-P indoor ONT Replace an I-240W-P, I-240W-Q, I-240W-R, I-240W-T, or I-241W-P indoor ONT Activation methods ONT and MDU overview SLID entry via Ethernet port HTTP management (1 of 2) Information necessary to manage an ONT at a local site using an HTTP interface, CLI interface, CLI interface, or butt set. ONT management using an ONT interface Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

333 38 I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P unit data sheet Feature Chapter/description Click link for more information Statistics and performance monitoring Supported UPS configurations (2 of 2) ONT and MDU statistics and performance monitoring Part numbers, ordering, and deployment configuration overview Performance monitoring statistics for Package C ONTs ONT and MDU to UPS or power adapter compatibility support 38.4 I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P interfaces and interface capacity Table 38-3 describes the supported interfaces and interface capacity for I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P indoor ONTs. Table 38-3 I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P indoor ONT interface connection capacity ONT type and model Maximum capacity POTS 10/ 100 BASE-T 10/ 100/ 1000 BASE-T RF video (CATV) MoCA VDSL2 E1/T1 Local craft GPON SC/ APC I-240W-P (1) I-240W-Q (1) I-240W-R (1) I-240W-T (1) I-241W-P (1) Note (1) The I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P ONTs provide Wi-Fi service that is enabled and disabled using a radio on/off switch. I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P connections and components I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P are indoor ONTs for indoor deployment and can be installed horizontally on a flat surface as well as attached to a wall. These ONTs feature a removable fiber access tray for storing excess cable and Wi-Fi service that is enabled and disabled using a radio on/off switch. Other features of these indoor ONTs include an ON/OFF power switch for manual shutdown (I-240W-P and I-241W-P excluded) a reset button two external, three-directional antennae 38-6 November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

334 38 I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P unit data sheet Figure 38-1 shows the I-240W-P indoor ONTs physical connections. Figure 38-1 I-240W-P indoor ONT connections GE POTS Ethernet ports (RJ45) POTS ports (RJ-11) Wi-Fi on/off switch A B WiFi ON OFF Power connector PWR 12VDC GPON 2.5G/1.25G G B+ Class 1 Laser Fiber optic connector (internal) Figures 38-2 and 38-3 show I-240W-Q, I-240W-R, and I-240W-T indoor ONT physical connections. Figure 38-2 I-240W-Q, I-240W-R, and I-240W-T indoor ONT connections (back view) TEL1 TEL2 LAN1 LAN2 LAN3 LAN4 ON/OFF POWER OPTICAL POTS ports (RJ-11) Ethernet ports (RJ-45) Power On/Off switch Power connector Fiber optic connector Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

335 38 I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P unit data sheet Figure 38-3 I-240W-Q, I-240W-R, and I-240W-T indoor ONT connections (side view) USB2 USB1 WPS RESET WLAN USB ports Wi-Fi Protected Setup Reset button WLAN button Figure 38-4 shows I-241W-P indoor ONT physical connections. Figure 38-4 I-241W-P indoor ONT connections GE POTS Ethernet ports (RJ45) POTS ports (RJ-11) Wi-Fi on/off switch F-Type coaxial connector A B WiFi ON OFF RF Power connector PWR 12VDC GPON 2.5G/1.25G G B+ Class 1 Laser Fiber optic connector (internal) Table 38-4 describes the I-240W-P, I-240W-Q, I-240W-R, and I-240W-T indoor ONT physical connections. Table 38-5 describes the I-241W-P indoor ONT physical connections November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

336 38 I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P unit data sheet Table 38-4 I-240W-P, I-240W-Q, I-240W-R, and I-240W-T indoor ONT physical connections Connection (1) Ethernet ports POTS WLAN button WPS button Power Fiber optic USB ports Description For I-240W-P, I-240W-Q, and I-240W-T ONT, this connection is provided through Ethernet RJ-45 cables. Up to four 10/100/1000 Base-T Ethernet interfaces are supported.the Ethernet ports can support both data and in-band video services on all four interfaces. For the I-240W-R ONT, this connection is provided through Ethernet RJ-45 cables. Up to four 10/100 Base-T Ethernet interfaces are supported.the Ethernet ports can support both data and in-band video services on all four interfaces. This connection is provided through RJ-11 ports. Up to two POTS connections are supported.the POTS ports support voice services. Wi-Fi service is compliant with IEEE standards and is enabled and disabled using a radio on/off switch. For I-240W-Q, I-240W-R, and I-240W-T ONTs, the Wi-Fi switch is labelled WLAN. For I-240W-Q, I-240W-R, and I-240W-T ONTs, the Wi-Fi Protected Setup switch is labelled WPS. This button enables and disables WLAN data encryption. This connection is provided through the power connector. A power cable fitted with a barrel connector is used to make the connection. For the I-240W-R ONT, the power connection is provided by either a 2-pin power adaptor or optional 8-pin power input with UPS monitoring. For the I-240W-T ONT, the power connection is provided through a 2-pin power adaptor. For I-240W-P ONT, this connection is provided through a SC/APC fiber optic connector located behind a fiber optic port cover. For I-240W-Q, I-240W-R, and I-240W-T ONTs, this connection is provided through a SC/APC fiber optic connector without a fiber optic port cover. For I-240W-Q, I-240W-R, and I-240W-T ONTs, this connection is provided through USB ports. Up to two USB host interfaces are supported. Note (1) The primary path for the earth ground for these ONTs is provided by the 12V Return signal in the power connector. Table 38-5 I-241W-P indoor ONT physical connections Connection (1) Ethernet ports POTS Wi-Fi interface Description This connection is provided through Ethernet RJ-45 cables. Up to four 10/100/1000 Base-T Ethernet interfaces are supported.the Ethernet ports can support both data and in-band video services on all four interfaces. This connection is provided through RJ-11 ports. Up to two POTS connections are supported.the POTS ports support voice services. Wi-Fi service is compliant with IEEE standard and enabled and disabled using an on/off switch. (1 of 2) Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

337 RESET 38 I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P unit data sheet Connection (1) RF video coaxial Power Fiber optic Description This connection is provided through a F-Type coaxial connector. This connection is provided through the power connector. A power cable fitted with a barrel connector is used to make the connection. This connection is provided through a SC/APC fiber optic connector. The fiber optic connector is located behind a fiber optic port cover. (2 of 2) Note (1) The primary path for the earth ground for these ONTs is provided by the 12V Return signal in the power connector I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P LEDs Figure 38-5 shows the I-240W-P and I-241W-P indoor ONT LEDs. Figure 38-5 I-240W-P and I-241W-P indoor ONT LEDs PWR GPON INET UPG ALARM POTS VIDEO WIFI Table 38-6 provides LED descriptions for I-240W-P and I-241W-P indoor ONTs November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

338 38 I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P unit data sheet Table 38-6 I-240W-P and I-241W-P indoor ONT LEDs Indicator LED color and behavior LED behavior description PWR GPON INET UPG ALARM POTS WIFI I-241W-P only VIDEO Green solid Green flashing (fast) Green flashing (slow) Red solid Red solid Green solid Green flashing Off Off Green solid Green flashing Off Green flashing Red solid Off Green solid Red solid Red flashing Off Green solid Green flashing Off Green solid Green flashing Off Green Operating on AC power System booting Operating from battery power Battery low Equipment failure or not ranged or synchronized ONT initial ranging is complete ONT is ranging and synchronizing Emergency stop state WAN is not configured Internet is connected PPPoE/DHCP signup is proceeding Normal Upgrading Upgrade failure No alarm No alarm with local access enabled ONT hardware is out of order ONT software failure All phones are on-hook One or more phones are off-hook One or more phones has been off-hook for at least one hour Wi-fi is disabled Wi-fi is configured and enabled Wi-fi is active RF is disabled or the video optical band being received is lower than the prescribed limit RF is enabled and optical signal power is working Figure 38-6 shows the I-240W-Q, I-240W-R, and I-240W-T indoor ONT LEDs. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

339 38 I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P unit data sheet Figure 38-6 I-240W-Q, I-240W-R, and I-240W-T indoor ONT LEDs USB2 USB1 WLAN WPS VoIP TEL2 TEL1 LAN4 LAN3 LAN2 LAN1 AUTH LINK POWER Table 38-7 provides LED descriptions for I-240W-Q, I-240W-R, and I-240W-T indoor ONTs. Table 38-7 I-240W-Q, I-240W-R and I-240W-T indoor ONT LEDs Indicator LED color and behavior LED behavior description POWER LINK AUTH LAN1 to LAN4 TEL1 and TEL2 VoIP WPS WLAN (1 of 2) Off Green solid Off Green solid Off Green solid Off Green solid Off Green solid Green flashing Off Green solid Off Green solid Red solid Off Green solid Green flashing No power Operating on AC power Failure on the PON link PON link is operating without failure ONU is not authorized ONU is authorized Not active Active On-hook Off-hook Incoming call VoIP is experiencing failure VoIP is operating without failure WPS is disable In Progress and Success status Error and Session Overlap status Error/WLAN is not connected/wlan disable Connected Data received and transferred (2H flash) November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

340 38 I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P unit data sheet Indicator LED color and behavior LED behavior description USB1 and USB2 Internet (2 of 2) Off Green solid Green flashing Off Green solid Green flashing No power/error/usb is not connected/usb disable Connected Data received and transferred (2H flash) WAN is not configured PPPoE/DHCP signup is successful. Internet is connected. Obtaining IP with PPPoE/DHCP 38.6 I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P detailed specifications Table 38-8 lists the physical specifications for I-240W-P and I-241W-P indoor ONTs. Table 38-8 I-240W-P and I-241W-P indoor ONT physical specifications Description Length Width Height Specification 2.6 in. (6.6 cm) 10.5 in. (26.7 cm) 7.9 in. (20 cm) Weight [within ± 0.5 lb (0.23 kg)] 2.2 lb (990 g) Table 38-9 lists the physical specifications for I-240W-Q, I-240W-R, and I-240W-T indoor ONTs. Table 38-9 I-240W-Q, I-240W-R, and I-240W-T indoor ONT physical specifications Dimensions Height Width Depth Weight [within ± 0.5 lb (0.23 kg)] Specifications 7.9 in. (20 cm) 6.3 in. (16 cm) 1.3 in. (3.3 cm) 0.9 lb (0.42 kg) [excluding power adaptor] Table lists the power consumption specifications for I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P indoor ONTs. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

341 38 I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P unit data sheet Table I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P indoor ONT power consumption specifications Mnemonic Maximum power (Not to exceed) Condition Minimum power Condition I-240W-P 15 W 2 POTS off-hook, 4 Gig-E, Wi-Fi operational I-240W-Q 15 W 2 POTS off-hook, 4 Gig-E, Wi-Fi operational I-240W-R 15 W 2 POTS off-hook, 4 Ethernet operational I-240W-T 16 W 2 POTS off-hook, 4 Gig-E, Wi-Fi operational I-241W-P 14.6 W 2 POTS off-hook, 4 Gig-E, RF video, Wi-Fi operational 5.5 W 2 POTS on-hook, other interfaces/services not provisioned 4.5 W 2 POTS on-hook, other interfaces/service not provisioned 4.5 W 2 POTS on-hook, other interfaces/service not provisioned 4.5 W 2 POTS on-hook, other interfaces/services not provisioned 5.5 W 2 POTS on-hook, other interfaces/services not provisioned Table lists the environmental specifications for I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P indoor ONTs. Table I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P indoor ONT environmental specifications Mounting method Temperature range and humidity Altitude Indoor 10/100/1000Base-T Gigabit Ethernet ONTs (I-240W-P and I-241W-P) Desk or wall mounted Operating: 32 F to 104 F (0 C to 40 C) ambient temperature 5% to 90% relative humidity, non-condensing Storage: Contact your Alcatel-Lucent support representative for more information Contact your Alcatel-Lucent technical support representative for more information Indoor 10/100Base-T Ethernet Wi-Fi ONTs (I-240W-R) and 10/100/1000Base-T Ethernet Wi-Fi ONTs (I-240W-Q, I-240W-T) Desk or wall mounted Operating: 32 F to 104 F (0 C to 40 C) ambient temperature 10% to 90% relative humidity, non-condensing Storage: Contact your Alcatel-Lucent support representative for more information Contact your Alcatel-Lucent technical support representative for more information November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

342 38 I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P unit data sheet 38.7 I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P GEM ports and T-CONTs Table lists the maximum number of supported T-CONTs and GEM ports. Not all ONTs will be supported in all of the releases indicated the table. See the appropriate release Customer Release Notes for the most accurate list of supported devices. Table I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P indoor ONT capacity for GEM ports and T-CONTs per package and release ONT or MDU Release Maximum Notes Package C ONTs GEM ports per indoor or outdoor ONT R to R are present: 10 are available, 2 are reserved for multicast and debugging All other releases are present: 30 are available, 2 are reserved for multicast and debugging T-CONTs per indoor or outdoor ONT R to R ,R x, R , R , R R x, R x, R x, R x, R x 6 7 are present: 6 are available, 1 is reserved for OMCI are present: 15 are available, 1 is reserved for OMCI R x, R x, R x are present: 31 are available, 1 is reserved for OMCI 38.8 I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P power support I-240W-P and I-241W-P indoor ONTs support the following power supply: Leader Electronics 12W, 18W, and 24W ac/dc switching power supply unit data sheet I-240W-R, and I-240W-T indoor ONTs support the following power supply: DVE 24 W ac/dc switching power adapter unit data sheet 38.9 I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P functional blocks Table describes the supported interfaces for I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P indoor ONTs. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

343 38 I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P unit data sheet Table I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P indoor ONT interfaces ONT category description Interface capacity POTS ports Ethernet ports VDSL2 MoCA RF Video HPNA Wi-Fi Single-residence Wi-Fi ONTs with Gigabit Ethernet ONTs and POTS and with or without RF video (I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P indoor ONTs) 2 4 0/1 1 I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P indoor ONTs are single-residence ONTs that support Wireless (Wi-Fi) service. Wi-Fi service on these ONTs are compliant with the IEEE standard and enabled or disabled using a radio on/off switch. In addition to the Wi-Fi service, these ONTs transmit Ethernet packets to four RJ-45 Ethernet ports, voice traffic to two RJ-11 POTS ports, and, on the I-241W-P ONT, RF video traffic to one F-type coaxial connector. These ONTs also feature fiber optic and power connectors. Figure 38-7 shows functional blocks for I-241W-P indoor ONTs with Gigabit Ethernet, POTS, and coaxial interface for RF video. This ONT has a triplexer and RF filter. Figure 38-7 Single-residence Wi-Fi ONT with Gigabit Ethernet, POTS, and RF video (triplexer) Power Converter Power connector GPON SOC POTS (2) GigE (4) RJ-11 RJ-45 Triplexer RF Filter F-type connector Figure 38-8 shows functional blocks for I-240W-P, I-240W-Q, I-240W-R, and I-240W-T indoor ONTs. These ONTs have the same functional blocks as the I-241W-P indoor ONT except for the triplexer and RF filter November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

344 38 I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P unit data sheet Figure 38-8 Single-residence Wi-Fi ONT with Gigabit Ethernet and POTS and without RF video Diplexer SC/APC GPON SOC RESET WiFi POTS GE PHY switch WiFi switch ISB 2.0 Host 2xRJ11 4xRJ45 PWR 2 x USB I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P indoor ONTs are single-residence Gigabit Ethernet ONTs with POTS and Ethernet ports. These ONTs transmit Ethernet packets to four RJ-45 Ethernet ports and voice traffic to four RJ-11 POTS ports. This ONT also features fiber optic and power connectors. ONT SoC technology serves as the main hardware block for these ONTs; see Figure Figure 38-9 I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P ONT hardware block POTS ports Control processor SoC DSP SoC Bridge Ethernet MACs GPON MAC Ethernet ports GPON Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

345 38 I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P unit data sheet ONT SoC technology consists of five key elements: GPON MAC The Gigabit Passive Optical Network Media Access Control (GPON MAC) element on the SoC terminates the GPON interface using an optical diplexer. This interface supports GPON as described in G (GPON TC Layer) ITU specification. Ethernet MAC The SoC provides up to four GE MACs. DSP interface The Digital Signal Processor (DSP) provides voice processing for 2 POTS lines with 3-way calling. The DSP has a dedicated 64 kbyte instruction cache and shares a 32 kbyte data cache with the Control Processor. Control Processor The Control Processor features an integral memory management unit that supports a dedicated 64 kbyte instruction cache and shares a single 32 kbyte data cache with the DSP. The Control Processor and DSP also include a single channel Data Management Application (DMA) controller with a 4 kbyte read ahead low-latency Dynamic Random Access Memory (DRAM) access port. The processors typically run at 400 MHz. Switch matrix The Switch matrix provides an integrated data channel between the four GE MACs, the GPON MAC, the DSP, the control processor, and the other integrated elements such as flash memory, DRAM, and the local bus controller. These ONTs can also interact with additional hardware components to support functionality not provided by the SoC technology I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P standards compliance I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P indoor ONTs are compliant with the following standards: 802.1p support for mapping and mapper service profile on U/S 802.1p support for marking and remarking 802.1p support for Class of Service based on VLAN-ID 802.1q support for virtual switch based on VLAN b support for maximum transmit power (EIRP) equal to or greater than 200 mw (23.01 dbm) g support for maximum transmit power (EIRP) equal to or greater than 100 mw (20 dbm) g/n support for processing that does not degrade the committed LAN-LAN and/or LAN-WAN throughput rate G.711 support for FAX, modem connection, and TTY devices G.984 support GPON interface (framing) G support for Amd1, class B+ G support for activation and password functions November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

346 38 I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P unit data sheet G support for AES with operator enable/disable on per port-id level G support for FEC in both upstream and downstream directions G support for multicast using a single GEM Port-ID for all video traffic G984.4 and G support for OMCI interface for ONT management and provisioning I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P special considerations Service creation considerations and limitations Port-to-port mode must be enabled when using the four-port Ethernet ONT I-240W-P and I-241W-P indoor ONTs. When using port-to-port mode, you can only configure one Ethernet port. Upgrade considerations and limitations Existing ONTs that use 7342 ISAM FTTU releases older than R04.06.xx and R04.07.xx must be upgraded to use R software while assigned to a PON ID value smaller than 64. For this purpose, if split ratios larger than 1:64 are being deployed, you may choose to set aside the first PON ID as a staging point. I-240W-P and I-241W-P indoor ONTs support voice, video, and HSI data services. These ONTs, which features Wi-Fi technology, can also function as a residential gateway with layer 2 and layer 3 processing capabilities. I-240W-P, I-240W-Q, I-240W-R, I-240W-T and I-241W-P ONT considerations and limitations Table lists the considerations and limitations for these ONTs. Table I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P ONT considerations and limitations Considerations and limitations Support for up to 32 GEM ports per Ethernet UNI Support for 7 T-CONTs including the OMCI T-CONT Ethernet OAM (802.1 ag) is not supported TPID overwrite is not supported Anti-spoofing is supported on I-020G-P and I-120G-P ONTs by treating PPPoE packets in the same manner as IPoE packets when anti-spoofing is configured. Other ONTs do not support anti-spoofing x is not supported IGMPv3 snooping with SSM is not supported VLAN translation is supported prior to replication for downstream IPTV multicast. The same VLAN operation must be provisioned for all Ethernet UNIs participating in IPTV multicasting. The ONT will not support sending some untagged multicast frames through one Ethernet UNI while sending other tagged multicast frames through another Ethernet UNI. (1 of 3) Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

347 38 I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P unit data sheet Considerations and limitations Double-tagged frames are not supported Flow control is not supported. The ONT will not generate PAUSE frames for the client if there is traffic congestion. Configurable Ethernet for VLAN tag detection is not supported. Currently, only 0x8100 is supported. POTS pull-break-dial-tone (PBDT) is not supported for SIP, H.248, and G6 Call history data collection (ONTCALLHST) is not supported G.729 and G.711 a/u are supported while G codec is not supported Only one global DSCP to pbit mapping table is supported Default Ethernet flow and wildcard Ethernet flow coexisting on the same Ethernet port is not supported Maximum of 16 service flows (VLANs) can be enabled with pbit translation Non-supported call services: Direct connect Warm line Call forward status indications Home Intercom Call park Bridged line Call pickup with barge-in Suppressed ringing Service classification by Ethertype is not supported The first time an ONT is connected, the initial Ethernet UNI is enabled by default. This Ethernet UNI can be disabled by the OLT. When pbit translation is enabled, each GEM port can only translate into one pbit. Mapping downstream Pbits to different GEM ports is the only form of supported pbit translation. Static multicast is not supported IPTV multicast over PPPoE (from the multicast port) is not supported PM counter is partially supported Pbit translation following DSCP to pbit mapping is not supported Pbit translation when a UNI is set to pass through any VLAN ID (unisidevlan=4096 and networksidevlan=4096) is not supported Packet loss occurs in 1G wirespeed. Due to the additional 4-byte routing tag, throughput is less than 1G for all packet lengths. Weighted round robin (WRR) is not accurate when configured with OMCI because the weight definition in BL device is the reverse of OMCI definition For WRR scheduling, bandwidth is not used by a queue can not be claimed by any other queues Up to eight extended VLAN rules per VLAN port is supported AES key can not be changed locally on an ONT 100M half is not supported When the Ethernet cable of the ONT is pulled and the services go out-of-service (OOS), traffic is still forwarded and MAC addresses are still learned when wireless is enabled. (2 of 3) November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

348 38 I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P unit data sheet Considerations and limitations As of R and later, the ONT support stacked VLAN ibridges mode. With a stacked VLAN ibridge, in addition to performing bringing operations, the ONT supports when the ISAM can add/remove a VLAN header to customer upstream or downstream traffic, which allows support for different broadband access solutions. (3 of 3) Voice, video, and data services The voice service on I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P indoor ONTs is delivered by up to two POTS ports that support: five REN per line (balanced ring at 55 V rms) multiple voice codec echo cancelling, VAD, and CNG static or dynamic jitter buffer various CLASS services including caller ID, call waiting, and call transfer SIP (RFC3261) or MEGACO v2 (H.248) multiple country profiles Two types of video service are supported on this ONT: RF video overlay (supported by I-241W-P only) IPTV/VoD by unicast or multicast For unicast IPTV/VoD, a triplexer is used to deliver a dedicated wavelength that carries a video broadcast signal to the subscriber. For multicast IPTV/VoD that delivers video content through data channels, the ONT supports a dedicated multicast GEM port on the downstream. Bandwidth efficiency is improved by having the video contents received and processed by all the ONTs on the same PON link through a unified channel. The HSI data service on these ONTs (except I-240W-R) is delivered by up to four 10/100/1000 Base-T Ethernet ports that support: auto-negotiation and MDI/MDIX auto-sensing layer 2 data transferring at wire speed for all packet sizes built-in layer 2 switch advanced data features such as VLAN tag manipulation, classification, and filtering built-in layer 3 routing and residential gateway The same data service is delivered on the I-240W-R indoor ONT by up to four 10/100 Base-T Ethernet ports. The I-240W-Q, I-240W-R, and I-240W-T ONTs also support two USB host interfaces compliant to USB 2.0. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

349 38 I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P unit data sheet Additional supported features In addition to voice, video, and data service, I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P indoor ONTs support Ethernet bridging and IP routing and firewall features. The following Ethernet bridging features are supported: wirespeed forwarding hardware priority queues in the upstream and downstream direction in support of CoS virtual switching based on 802.1q VLAN up to 256 MAC address and 16 VLAN groups (I-240W-T ONT excluded) VLAN tagging/detagging per Ethernet port VLAN stacking (Q-in-Q) and VLAN translation IP ToS/DSCP to 802.1p mapping CoS based on VLAN-ID, 802.1p bit, ToS/DSCP marking/remarking of 802.1p IGMP v2/v3 snooping broadcast/multicast rate limiting MAC address limiting (I-240W-T ONT excluded) Supported IP routing and firewall features including the following: PPPoE NAT and NAPT port forwarding, ALGs, UPnP integrated stateful packet inspection firewall with ACL VPN pass-though for PPTP, L2TP, and IPsec static routing and RIP2 dynamic routing (I-240W-T ONT excluded) DHCP client/server DNS client/server Wi-Fi service I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P indoor ONTs feature Wi-Fi service as well as voice, video, and data services. Wi-Fi is a wireless networking technology that uses radio waves to provide wireless HSI and network connections. This ONT complies with the IEEE standards, which the Wi-Fi Alliance defines as the basis for Wi-Fi technology. Wi-Fi physical features I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P indoor ONTs have the following physical features that assist in providing Wi-Fi service: on/off radio switch for enabling and disabling Wi-Fi service two external multi-directional antennae November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

350 38 I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P unit data sheet Wi-Fi standards and certifications The Wi-Fi service on I-240W-P, I-240W-Q, I-240W-R, I-240W-T and I-241W-P indoor ONTs supports the following IEEE standards and Wi-Fi Alliance certifications: compliant with IEEE standards certified for IEEE a/b/e/g/h/n standards certified for IEEE b/g/n standards (for I-240W-T) WPA support including WPA-PSK certified for WPA2-Personal and WPA2-Enterprise certified for WMM and WMM scheduled access certified for WPS as an AP type device with registrar support Wi-Fi GUI features I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P indoor ONTs have HTML-based Wi-Fi configuration GUIs containing the following features: configuration of the best available channel to a fixed value selection of the LAN devices allowed to access the ONT through a wireless interface (for example, MAC address filtering) operational status indicators for numerous data elements entry of Wi-Fi device WPS PIN codes disabling of the broadcasting of the primary user SSID (default broadcasting must be enabled) user scheduling of the enabling and disabling of the Wi-Fi connection Wi-Fi access point features I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P indoor ONTs have the following Wi-Fi access point features: ability to scan the frequency spectrum and select the best available channel and power up following a reset MAC address filtering ability for a minimum of 32 devices to simultaneously connect to the AP of the device 64- and 128-bit WEP support support for both the entry of hexadecimal encryption keys used by WEP and ASCII-based pass phrases when working with WPA support for two SSIDs each with its own unique characteristics including protocol configuration, data rate supported, authentication, encryption, and broadcasting status. blocking of association requests that do not specify a valid SSID support for WDS that allows the ONT to act as a base station for a user-configured list of specific repeaters Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

351 38 I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P unit data sheet Residential gateway functions As a residential gateway, I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P indoor ONTs feature layer 2 and 3 processing capabilities and support the following home router functions: PPPoE or 802.1x for WAN interface NAPT and firewall DHCP/DNS service (client and server) port-forwarding, ALCG, and UPnP routing VPN pass-through Residential gateway rules and requirements I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P indoor ONTs act as a router that allows each device in the network to communicate with any other device. The following functions can be configured on these router ONTs: DHCP service IP routing and NAT function on the ONT DNS requirements IGMP functionality UPnP Note Do not configure the I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P indoor ONT as a router for the home network by using a bridge concept for all the devices in the home. DHCP service DHCP allows individual clients to obtain IP configuration from a server at start-up. DHCP can function in one of the following two ways: DHCP server for the LAN An internal DHCP server allocates IP addresses to all the network devices attached to the ONT. DHCP client instances on the WAN The ONT receives an IP addresses for each type of client instance from 23 different DHCP servers in the WAN network: one DHCP client instance for obtaining a public IP address for HSI data traffic one DHCP client instance for VoIP for obtaining a private IP address from the WAN network for voice (dedicated VLAN) Figure shows a diagram of the LAN (DHCP server) and WAN (DHCP client) DCHP service on an ONT November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

352 38 I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P unit data sheet Figure LAN and WAN functions of the DCHP service VoIP ONT STBx IPTV STBx PC Others DHCP server DHCP client for HSI data DHCP client for VoIP voice Devices connected to ONT IP addresses from DHCP server IP routing IP routing allows the network to be routed so that all devices in the home can communicate with each other. In this case, IP routing uses NAT to translate the IP address of a host within a packet. NAT is employed in one of the following two ways: HSI traffic is directed to a public IP address The default gateway that will route the HSI traffic has its address transmitted to the ONT router using DHCP Option 3. Video traffic is directed to a private IP address Routes used for the IPTV service are transmitted to the ONT router using DHCP Option 121. NAT rules are not used for VoIP traffic since the routes used by this traffic are received by DHCP Option 121. DNS requirements DNS maps a domain name to its corresponding IP address and vice versa. For the WAN, the ONT receives two sets of DNS addresses: The first set of received DNS addresses are the primary and secondary addresses from the IP edge for HSI traffic. The second set of received DNS addresses are the primary and secondary addresses from the IP edge for video services. All four of these addresses are transmitted using DHCP Option 6. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

353 38 I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P unit data sheet IGMP functionality IGMP is a network-layer protocol used to establish membership in a multicast group and not to carry user data. When enabled on these ONTs, IGMP possesses fast-leave capabilities as well as proxy and snooping functions. Also, the IGMP engine on the ONT features explicit host-tracking of IGMP requests. If two set-top boxes are seeking to access the same multicast channel, and one of them is leaving the channel, then the router will keep the channel available for the other set-top box. UPnP UPnP is a distributed open networking standard that uses TCP/IP for simple peer-to-peer network connectivity between devices. A UPnP device can dynamically join a network, obtain an IP address, convey its capabilities, and learn about other devices on the network. Also, a UPnP device can leave a network smoothly and automatically when it is no longer in use. Since the I-240W-Q, I-240W-R and I-241W-P indoor ONT can act as a router for networks with multiple devices, they have UPnP for their WAN traffic. Web-based ONT configuration and reporting I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P indoor ONTs support limited configuration using a web-based GUI. Using the GUI, you can configure or view information for the following options: network security application maintain status Procedure 38-1 Login to web-based GUI 1 Open a web browser and enter the IP address of the ONT in the address bar. The login window appears. The default gateway IP address is You can also obtain the IP address using DHCP after connecting your PC to the layer 3 UNI. 2 Enter your username and password in the Login window. The default username is root while the default password is admin. Caution If you reset the router to recover the default username and password, all other router configuration settings will also be restored to their factory default values November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

354 38 I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P unit data sheet Note If you forget the current username and password, press the reset button for 5 s and the default values for the username and password will be recovered upon start up 3 Click OK. 4 STOP. This procedure is complete. Network configuration using the web-based GUI The following procedures provide the steps for configuring the network settings for the LAN, WAN, Wi-Fi, routing, DNS, and TR-069 service. Procedure 38-2 Network LAN configuration 1 Select the LAN option from the Network section of the navigation tree in the GPON ONT window. The LAN window appears; see Figure Figure LAN window 2 Configure the LAN parameters. Table describes the fields in the LAN window. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

355 38 I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P unit data sheet Table LAN parameters Field IP Address Subnet mask DHCP Enable DHCP Start IP Address DHCP End IP Address Max Number of DHCP Users DHCP Lease Time Bind MAC Address Bind IP Address Description IP address of the LAN interface in dotted-decimal format. For example, a sample IP address is Subnet mask of the IP addresses in your LAN. The default is Select or clear the DHCP Enable radio button. If enabled, the ONT assigns IP addresses, an IP default gateway, and DNS servers to computers that support the DHCP client; for example, Windows 95, Windows NT. Starting IP address of the DHCP IP pool Last IP address in the DHCP IP pool Maximum number of DHCP users Number of minutes of client lease time. A zero means one day of lease time Bind MAC Address Bind IP Address 3 If required, click Add to build a list of Bind MAC and IP addresses. 4 Click Apply to save your changes or Refresh to clear the fields. Note By default, the LAN DHCP server is enabled. If the PC cannot get the IP address using DHCP, click Reset on the PC for 5 s and the default values for the LAN DHCP server will be recovered upon start up. 5 STOP. This procedure is complete. Procedure 38-3 Network WAN configuration 1 Select the WAN option from the Network section of the navigation tree in the GPON ONT window. The WAN window appears. Depending on the software you are using, the WAN window may vary. 2 Select one of the following options to obtain the WAN IP address from the Internet Connection Type drop-down menu. i PPPoE The WAN window appears with the PPPoE tab displayed; see Figure November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

356 38 I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P unit data sheet Figure PPPoE tab of the WAN window Configure the PPPoE parameters. Table describes the PPPoE field parameters in the WAN window. Table PPPoE field parameters Field WAN Connection List Delete Enable/Disable NAT Service: Enable VLAN VLAN ID VLAN PRI WAN IP Mode Username Password Keep Alive Time Description Select a WAN connection from the list in the drop-down menu Select the Delete check box to remove the WAN connection selected from the WAN connection list Select or clear the Enable/Disable check box Select or clear the NAT check box to enable or disable Network Address Translation (NAT) Select the check box for one of the following services: VoIP, TR-069, Internet, or IPTV Select the Enable VLAN check box to enable Virtual Local Area Network (VLAN) Enter the identification number for the VLAN Enter the Primary Rate Interface (PRI) for the VLAN Select PPPoE from the WAN IP mode drop-down menu Username for the PPPoE connection Password for the PPPoE connection Set the duration (in seconds between 5 and 60) to keep alive a connection Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

357 38 I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P unit data sheet ii Automatic Configuration - DHCP The WAN window appears with the Automatic Configuration - DHCP tab displayed; see Figure Figure Automatic Configuration - DHCP tab of the WAN window You can connect or disconnect any DHCP connection by using the Disconnect and Connect buttons. Table describes the DHCP field parameters in the WAN window. Table DHCP parameters Field WAN Connection List Delete Enable/Disable NAT Service: Enable VLAN VLAN ID VLAN PRI WAN IP Mode Description Select a WAN connection from the list in the drop-down menu Select the Delete check box to remove the WAN connection selected from the WAN connection list Select or clear the Enable/Disable check box Select or clear the NAT check box to enable or disable Network Address Translation (NAT) Select the check box for one of the following services: VoIP, TR-069, Internet, or IPTV Select the Enable VLAN check box to enable Virtual Local Area Network (VLAN) Enter the identification number for the VLAN Enter the Primary Rate Interface (PRI) for the VLAN Select DHCP from the WAN IP mode drop-down menu iii Static IP November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

358 38 I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P unit data sheet The WAN window appears with the Static IP tab displayed; see Figure Figure Static IP tab of WAN window Configure the Static IP parameters. Table describes the Static IP fields in the WAN window. Table Static IP parameters Field WAN Connection List Delete Enable/Disable NAT Service: Enable VLAN VLAN ID VLAN PRI WAN IP Mode IP Address Description Select a WAN connection from the list in the drop-down menu Select the Delete check box to remove the WAN connection selected from the WAN connection list Select or clear the Enable/Disable check box Select or clear the NAT check box to enable or disable Network Address Translation (NAT) Select the check box for one of the following services: VoIP, TR-069, Internet, or IPTV Select the Enable VLAN check box to enable Virtual Local Area Network (VLAN) Enter the identification number for the VLAN Enter the Primary Rate Interface (PRI) for the VLAN Select Static IP from the WAN IP mode drop-down menu IP address of the WAN interface in dotted-decimal format. For example, a sample IP address is (1 of 2) Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

359 38 I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P unit data sheet Field Netmask Gateway Description Subnet mask of the IP addresses in your WAN. The default is IP address of the node on the network that is chosen as default gateway when the IP address does not match any other routes in the routing table Pri DNS (2 of 2) 3 Click Apply to save your changes or Refresh to clear the fields. 4 STOP. This procedure is complete. Procedure 38-4 Network Wi-Fi configuration 1 Select the Wi-Fi option from the Network section of the navigation tree in the GPON ONT window. The WIFI window appears; see Figure November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

360 38 I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P unit data sheet Figure Wi-Fi window Configure the Wi-Fi parameters. Table describes the fields in the Wi-Fi window. Table Wi-Fi parameters Field Enable Mode Channel Transmitting Power WiFi Mac Filter SSID Select SSID Name Enable SSID SSID Broadcast Description Select the Enable check box to enable Wi-Fi Select the Wi-Fi mode from the drop-down menu. Default mode is Auto. Other options can be selected from the drop-down menu. Select either 25%, 50%, 75%, or 100% from the drop-down menu Select either Enable or Disable from the drop-down menu Select either SSID1 or SSID2 from the drop-down menu Enter a name for the SSID Select either Enable or Disable from the drop-down menu Select either Enable or Disable from the drop-down menu (1 of 2) Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

361 38 I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P unit data sheet Field SSID Isolate Enable WPS WPS Mode Description Select either Enable or Disable from the drop-down menu Select either Enable or Disable from the drop-down menu Select a WPS mode from the drop-down menu PIN Code Number Encrypt Mode WPA Version WPA Encryption Mode WPA Key Select a encryption mode from the drop-down menu Select a WPA option from the drop-down menu Select an WPA encryption mode from the drop-down menu Enter the WPA key number (2 of 2) 2 Click Apply to save your changes or Refresh to clear the fields. 3 STOP. This procedure is complete. Procedure 38-5 Network Routing configuration 1 Select the Routing option from the Network section of the navigation tree in the GPON ONT window. The Routing window appears; see Figure Figure Routing window Configure the Routing parameters. Table describes the fields in the Routing window November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

362 38 I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P unit data sheet Table Routing parameters Field Enable Routing Destination IP Address Destination Netmask Gateway IPV4 Interface Description Select or clear the Enable Routing check box to enable or disable routing Enter the IP address for the end destination for the connection Enter the netmask address for the end destination for the connection IP address of the node on the network that is chosen as default when the IP address does not match any other routes in the routing table Select an option from the drop-down menu 2 Click Apply to save your changes or Refresh to clear the fields. 3 STOP. This procedure is complete. Procedure 38-6 Network DNS configuration 1 Select the DNS option from the Network section of the navigation tree in the GPON ONT window. The DNS window appears; see Figure Figure DNS window Configure the DNS parameters. Table describes the fields in the DNS window. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

363 38 I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P unit data sheet Table DNS parameters Field Domain Name IP Address Description Enter the domain name Enter the IP address of the interface 2 Click Apply to save your changes or Refresh to clear the fields. 3 STOP. This procedure is complete. Procedure 38-7 Network TR-069 configuration 1 Select the TR-069 option from the Network section of the navigation tree in the GPON ONT window. The TR-069 window appears; see Figure Figure TR-069 window Configure the TR-069 parameters. Table describes the fields in the TR-069 window. Table TR-069 parameters Field Periodic Inform Enable Description Select or clear the check box Periodic Inform Interval(s) URL Username Enter the URL from which to perform remote management Enter the username (1 of 2) November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

364 38 I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P unit data sheet Field Password Description Enter the password Correct Request Username Correct Request Password (2 of 2) 2 Click Apply to save your changes or Refresh to clear the fields. 3 STOP. This procedure is complete. Security configuration using the web-based GUI The following procedures provide the steps for performing security ONT configuration including the setting up of firewalls, MAC filters, IP filters, DMZ and ALG. Procedure 38-8 Security firewall configuration 1 Select the Firewall option from the Security section of the navigation tree in the GPON Home Gateway window to configure the firewall protection level. The Firewall window is displayed; see Figure Figure Firewall window Configure the firewall protection level. Table describes the fields in the Firewall window. Table Firewall parameters Field Security Level Attack Protect Description Select either High or Low from the drop-down menu Select either Enable or Disable from the drop-down menu Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

365 38 I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P unit data sheet 2 Click Save to save your changes or Refresh to clear the fields. 3 STOP. This procedure is complete. Procedure 38-9 Security MAC Filter configuration 1 Select the MAC Filter option from the Security section of the navigation tree in the GPON Home Gateway window to configure the MAC Filter mode. The MAC Filter window is displayed; see Figure Figure MAC Filter window Configure the MAC filter mode. Table describes the fields in the MAC Filter window. Table MAC filter parameters Field Enable Mac Filter Mac Address Mac Filter Mode Description Select the check box to enable MAC filtering Select the IP address for the MAC Select either Black or White from the drop-down menu 2 If required, click Add to build a list of MAC filters. 3 Click Save to save your changes or Refresh to clear the fields. 4 STOP. This procedure is complete November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

366 38 I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P unit data sheet Procedure IP Filter configuration 1 Select the IP Filter option from the Security section of the navigation tree in the GPON Home Gateway window to configure the IP filter. The IP filter window is displayed; see Figure Figure IP Filter window Configure the IP filter mode. Table describes the fields in the IP Filter window. Table IP filter parameters Field Enable IP Filter Mode Source Start IP Address Source End IP Address Destination Start IPS Address Destination End IP Address Protocol Description Select the check box to enable IP filtering Select an option from the drop-down menu Enter the source IP address for the start of the connection Enter the source IP address for the end of the connection Enter the IP address for the start of the destination connection Enter the IP address for the end of the destination connection Select an option from the drop-down menu 2 If necessary, click Add to build a list of IP filters. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

367 38 I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P unit data sheet 3 Click Save to save your changes or Refresh to clear the fields. 4 STOP. This procedure is complete. Procedure DMZ and ALG configuration 1 Select the DMZ and ALG option from the Security section of the navigation tree in the GPON Home Gateway window to configure ALG or DMZ. The DMZ and ALG window is displayed; see Figure Figure DMZ and ALG window Configure the ALG function and DMZ server. Table describes the fields in the DMZ and ALG window. Table DMZ and ALG parameters Field Description ALG Config ALG Config Select the check box for one of the following services: FTP, TFTP, SIP, H323, RTSP, L2TP, or IPSEC DMZ Config WAN Connection List Enable DMZ Destination Start IPS Address DMZ IP Address Select a WAN connection from the list in the drop-down menu Select the check box to enable DMZ Enter the IP address for the start of the destination connection Enter the IP address for the DMZ November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

368 38 I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P unit data sheet 2 Click Save ALG or Save DMZ to save either the ALG type or DMZ server. 3 STOP. This procedure is complete. Application configuration using the web-based GUI The following procedures provide the steps for performing application tasks on the ONT. Procedure Port Forwarding configuration 1 Select the Port Forwarding option from the Application section of the navigation tree in the GPON Home Gateway window to configure port forwarding. The Port Forwarding window is displayed; see Figure Figure Port Forwarding window Configure the port forwarding parameters. Table describes the fields in the Port Forwarding window. Table Port forwarding parameters Field WAN Port LAN Port LAN IP Address Description Select an option from the drop-down menu or enter the IP address or URL of another network time protocol server Starting port number followed by the ending port number of the external host, in two fields IP address of the host that is currently blocked from the application (1 of 2) Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

369 38 I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P unit data sheet Field Protocol Enable Mapping WAN Connection List Description Protocol(s) used by the application. Options are: TCP UDP Both Check box to Enable to apply this filter rule; leave box unchecked to Disable this filter rule Select a WAN connection from the list in the drop-down menu (2 of 2) 2 Click Add to save your configuration changes. 3 STOP. This procedure is complete. Procedure DDNS configuration 1 Select the DDNS option from the Application section of the navigation tree in the GPON Home Gateway window to configure dynamic DNS. The DDNS window is displayed; see Figure Figure DDNS window Configure the DDNS parameters. Table describes the fields in the DDNS window. Table DDNS parameters Field WAN Connection List Description Select a WAN connection from the list in the drop-down menu (1 of 2) November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

370 38 I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P unit data sheet Field Enable DDNS ISP Domain Name Username Password Description Check box to enable dynamic DNS; leave box unchecked to disable dynamic DNS Select a ISP from the list in the drop-down menu Enter the domain name Username for the DDNS connection Password for the DDNS connection (2 of 2) 2 Click Save to save your changes or Refresh to clear the fields. 3 STOP. This procedure is complete. Procedure NTP configuration 1 Select the NTP option from the Application section of the navigation tree in the GPON Home Gateway window to configure the NTP. The NTP window is displayed; see Figure Figure NTP window Configure the NTP parameters. Table describes the fields in the NTP window. Table NTP parameters Field Enable NTP Service Description Check box to enable NTP; leave box unchecked to disable NTP (1 of 2) Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

371 38 I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P unit data sheet Field Current Time Description Time when the information was collected First Time Server Second Time Server Interval Time Time Zone Select a time zone from the drop-down menu (2 of 2) 2 Click Save to save your changes or Refresh to clear the fields. 3 STOP. This procedure is complete. Maintenance configuration using the web-based GUI The following procedures provide the steps for performing maintenance tasks on the ONT. Procedure Password configuration 1 Select the Password option from the Maintain section of the navigation tree in the GPON Home Gateway window to configure your password. The Password window is displayed; see Figure Figure Password window Configure the Password parameters. Table describes the fields in the Password window November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

372 38 I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P unit data sheet Table Password parameters Field Original Password New Password Re-enter Password Description Enter the current password New password other than the default one Verify the new password by re-entering it Prompt Message 2 Click Save to save your changes or Refresh to clear the fields. 3 STOP. This procedure is complete. Procedure SLID configuration 1 Select the SLID Configuration option from the Maintain section of the navigation tree in the GPON Home Gateway window to configure the SLID. The SLID configuration window is displayed; see Figure Figure SLID Configuration window Configure the SLID configuration parameters. Table describes the fields in the SLID configuration window. Table SLID configuration parameters Field Current SLID Description Display of the current SLID (1 of 2) Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

373 38 I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P unit data sheet Field Input New SLID SLID Mode Description Enter the new SLID Select a SLID mode from the drop-down menu. Options are: ASCII (2 of 2) 2 Click Save to save your changes or Refresh to clear the fields. 3 STOP. This procedure is complete. Procedure Backup and restore configuration 1 Select the Backup and Restore option from the Maintain section of the navigation tree in the GPON Home Gateway window to configure the backup. The Backup and Restore window is displayed; see Figure Figure Backup and Restore window Configure the Backup and Restore parameters. Table describes the fields in the Backup and Restore window. Table Backup and Restore parameters Field Select File Description Select the file for backup or restoration from the drop-down menu. Click November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

374 38 I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P unit data sheet 2 Click Import to import the configuration file or Export to export the configuration file. 3 STOP. This procedure is complete. Procedure Firmware Upgrade configuration 1 Select the Firmware Upgrade option from the Maintain section of the navigation tree in the GPON Home Gateway window to upgrade ONT firmware. The Firmware Upgrade window is displayed; see Figure Figure Firmware Upgrade window Configure the Firmware Upgrade parameters. Table describes the fields in the Firmware Upgrade window. Table Firmware upgrade parameters Field Select File Description Select the file for upgrade from the drop-down menu. Click 2 Click Upgrade to commence the upgrade. 3 STOP. This procedure is complete. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

375 38 I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P unit data sheet Procedure Reboot the ONT 1 Select the Reboot Device option from the Maintain section of the navigation tree in the GPON Home Gateway window to reboot. The Reboot Device window is displayed; see Figure Figure Reboot Device window 2 Click Reboot to reboot the device. 3 STOP. This procedure is complete. Procedure Reset the ONT to factory defaults 1 Select the Factory Default option from the Maintain section of the navigation tree in the GPON Home Gateway window to revert to the ONT factory default settings. The Factory Default window is displayed; see Figure November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

376 38 I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P unit data sheet Figure Factory Default window 2 Click Factory Default to revert to the ONT factory default settings. 3 STOP. This procedure is complete. Procedure Diagnose network problems 1 Select the Diagnose option from the Maintain section of the navigation tree in the GPON Home Gateway window to diagnose the network using ping or traceroute. The Diagnose window is displayed; see Figure Figure Diagnose window Configure the Diagnose parameters. Table describes the fields in the Diagnose window. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

377 38 I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P unit data sheet Table Diagnose parameters Field WAN Connection List IP or Domain Name Test Description Select a WAN connection from the list in the drop-down menu Enter the IP or domain name Select either the ping or traceroute check box 2 Click Start test to commence the test or Show result to display the test results. 3 STOP. This procedure is complete. Procedure Display operational log 1 Select the Log option from the Maintain section of the navigation tree in the GPON Home Gateway window to display the operational logs. The Log window is displayed; see Figure Figure Log window Configure the Log parameters. Table describes the fields in the Log window November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

378 38 I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P unit data sheet Table Log parameters Field Writing Level Reading Level Description Select a writing level from the drop-down menu. Options are: Debug Select a reading level from the drop-down menu. Options are: Debug 2 Click Save to save your changes or Refresh to clear the fields. 3 STOP. This procedure is complete. Status reports using the web-based GUI The following procedures provide the steps for obtaining ONT status information. Procedure Display device information 1 Select the Device Information option from the Status section of the navigation tree in the GPON Home Gateway window to present device information. The Device Information window is displayed; see Figure Figure Device Information window Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

379 38 I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P unit data sheet 2 Click Refresh to clear the fields and obtain updated data. 3 STOP. This procedure is complete. Procedure Display LAN status 1 Select the LAN Status option from the Status section of the navigation tree in the GPON Home Gateway window. The LAN Status window is displayed; see Figure Figure LAN Status window 2 Click Refresh to update the displayed information. 3 STOP. This procedure is complete. Procedure Display WAN status 1 Select the WAN Status option from the Status section of the navigation tree in the GPON Home Gateway window. The WAN Status window is displayed; see Figure November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

380 38 I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P unit data sheet Figure WAN Status window 2 Click Refresh to update the displayed information. 3 STOP. This procedure is complete. Procedure Display home networking information 1 Select the Home Networking option from the Status section of the navigation tree in the GPON Home Gateway window. The Home Networking window is displayed; see Figure Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

381 38 I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P unit data sheet Figure Home Networking window for the I-240W-Q indoor ONT 2 Click Refresh to update the displayed information. 3 STOP. This procedure is complete. Procedure Display the optics module status 1 Select the Optics Module Status option from the Status section of the navigation tree in the GPON Home Gateway window. The Optics Module Status window is displayed; see Figure Figure Optics Module Status window November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

382 38 I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P unit data sheet 2 Click Refresh to update the displayed information. 3 STOP. This procedure is complete. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

383 38 I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P unit data sheet November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

384 NTP 190 Install an I-240W-P, I-240W-Q, I-240W-R, I-240W-T, or I-241W-P indoor ONT Purpose This NTP provides the steps to install an I-240W-P, I-240W-Q, I-240W-R, I-240W-T, or I-241W-P indoor ONT. General The DLPs listed in this NTP describe mounting and cabling for I-240W-P, I-240W-Q, I-240W-R, I-240W-T, or I-241W-P indoor ONTs. Prerequisites See the listed DLPs for prerequisites. Recommended tools You need the following tools for the installation: #2 Phillips screwdriver 1/4 in. (6 mm) flat blade screwdriver wire strippers fiber optic splicing tools RJ-45 cable plug crimp tool voltmeter or multimeter optical power meter drill and drill bits Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November 2013 NTP FE AAAA TCZZA Edition 01

385 NTP 190 Install an I-240W-P, I-240W-Q, I-240W-R, I-240W-T, or I-241W-P indoor ONT Safety information Read the following safety information before installing the unit. Danger 1 Contact the local utility company before you connect the enclosure to the utilities. Danger 2 Observe the local and national laws and regulations that may be applicable to this installation. Danger 3 If the coaxial output of the ONT is connected to the dwelling infrastructure coaxial distribution system, ensure that the coaxial distribution system is separately grounded. Grounding of the dwelling coaxial infrastructure shall use Listed grounding devices and must be installed in accordance with local Codes and Article 800 of the National Electric Code, ANSI/NFPA 70, following the manufacturers instructions. Warning This equipment is ESD sensitive. Proper ESD protections should be used when removing the fiber access cover of the indoor ONT. Caution Keep indoor ONTs out of direct sunlight. Prolonged exposure to direct sunlight can damage the unit. Procedure Note Observe the following: The indoor ONT should be installed in accordance with the applicable requirements of the NEC or CEC. Local authorities and practices take precedent when there is conflict between the local standard and the NEC or CEC. The indoor ONT must be installed by qualified service personnel. Indoor ONTs must be installed with cables that are suitably rated and listed for indoor use. See the detailed specifications in the I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P unit data sheet for the temperature ranges for these ONTs. Use this procedure to install an I-240W-P, I-240W-Q, I-240W-R, I-240W-T, or I-241W-P indoor ONT. 1 Prepare the cables at the site where the ONT will be installed (DLP 100). 2 Are any of the cables missing? a If yes, go to step 3. b If no, go to step 4. 3 Locate each missing cable and route them to the ONT as per local practices. NTP November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

386 NTP 190 Install an I-240W-P, I-240W-Q, I-240W-R, I-240W-T, or I-241W-P indoor ONT 4 Place the indoor ONT unit: a On the flat surface, such as a desk. i ii iii Wrap the excess optic cable inside the fiber storage tray. Attach the fiber storage tray to the ONT. Place the ONT on the flat surface, horizontally resting on its four feet as shown in Figures NTP 190-1, NTP 190-2, and NTP Note The I-240W-P, I-240W-Q, I-240W-R, I-240W-T, or I-241W-P cannot be stacked with another ONT or with other equipment. The ONT mounting requirements are: allow a minimum 100 mm clearance above the top cover allow a minimum 50 mm clearance from the side vents do not place any heat source directly above the top cover or below the bottom cover iv Go to step 5. b On a wall (DLP 122). 5 Review the connection locations as shown in Figure NTP for I-240W-P indoor ONT, Figures NTP and NTP for I-240W-Q, I-240W-R, and I-240W-T indoor ONTs, and Figure NTP for I-241W-P indoor ONTs. Figure NTP 190-1: I-240W-P indoor ONT connections GE POTS Ethernet ports (RJ45) POTS ports (RJ-11) Wi-Fi on/off switch A B WiFi ON OFF Power connector PWR 12VDC GPON 2.5G/1.25G G B+ Class 1 Laser Fiber optic connector (internal) Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November 2013 NTP FE AAAA TCZZA Edition 01

387 NTP 190 Install an I-240W-P, I-240W-Q, I-240W-R, I-240W-T, or I-241W-P indoor ONT Figure NTP 190-2: I-240W-Q, I-240W-R, and I-240W-T indoor ONT connections (back view) TEL1 TEL2 LAN1 LAN2 LAN3 LAN4 ON/OFF POWER OPTICAL POTS ports (RJ-11) Ethernet ports (RJ-45) Power On/Off switch Power connector Fiber optic connector Figure NTP 190-3: I-240W-Q, I-240W-R, and I-240W-T indoor ONT connections (side view) USB2 USB1 WPS RESET WLAN USB ports Wi-Fi Protected Setup Reset button WLAN button NTP November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

388 NTP 190 Install an I-240W-P, I-240W-Q, I-240W-R, I-240W-T, or I-241W-P indoor ONT Figure NTP 190-4: I-241W-P indoor ONT connections GE POTS Ethernet ports (RJ45) POTS ports (RJ-11) Wi-Fi on/off switch F-Type coaxial connector A B WiFi ON OFF RF Power connector PWR 12VDC GPON 2.5G/1.25G G B+ Class 1 Laser Fiber optic connector (internal) Connect the Ethernet cables to the RJ-45 ports (DLP 101). 7 Connect the POTS cables to the RJ-11 ports (DLP 123). 8 For the I-241W-P indoor ONT only, connect the coaxial cable to the F-Type connector (DLP 116). 9 Connect the SC/APC fiber optic cable (DLP 125). Warning Be careful to maintain a bend radius of no less than 1.5 inches (3.8 cm) when connecting the fiber optic cable. Too small of a bend radius in the cable can result in damage to the optic fiber. 10 Install the power supply according to manufacturer specifications. Note Observe the following: Units must be powered by a Listed or CE approved and marked limited power source power supply with a minimum output rate of 12 V dc, 1.25 A. 11 Connect the power cable to the power connector. 12 For I-240W-Q, I-240W-R and I-240W-T ONTs, power up the ONT unit by using the ON/OFF power switch. 13 If used, enable the Wi-Fi service (DLP 130). 14 Verify the ONT LEDs, voltage status, and optical signal levels (DLP 127). 15 Activate and test the services (DLP 128). Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November 2013 NTP FE AAAA TCZZA Edition 01

389 NTP 190 Install an I-240W-P, I-240W-Q, I-240W-R, I-240W-T, or I-241W-P indoor ONT 16 If used, configure the SLID (DLP 129). 17 If necessary, reset the ONT (DLP 126). 18 STOP. This procedure is complete. NTP November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

390 NTP 191 Replace an I-240W-P, I-240W-Q, I-240W-R, I-240W-T, or I-241W-P indoor ONT Purpose This NTP provides the steps to replace I-240W-P, I-240W-Q, I-240W-R, I-240W-T, or I-241W-P indoor ONTs. General The DLPs listed in this NTP describe mounting and cabling for I-240W-P, I-240W-Q, I-240W-R, I-240W-T, or I-241W-P indoor ONTs. Prerequisites See the listed DLPs for prerequisites. Recommended tools You need the following tools for replacing the ONT: #2 Phillips screwdriver 1/4 in. (6 mm) flat blade screwdriver wire strippers fiber optic splicing tools RJ-45 cable plug crimp tool voltmeter or multimeter optical power meter drill and drill bits Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November 2013 NTP FE AAAA TCZZA Edition 01

391 NTP 191 Replace an I-240W-P, I-240W-Q, I-240W-R, I-240W-T, or I-241W-P indoor ONT Safety information Read the following safety information before replacing the unit. Danger 1 Contact the local utility company before you connect the enclosure to the utilities. Danger 2 Observe the local and national laws and regulations that may be applicable to this installation. Danger 3 If the coaxial output of the ONT is connected to the dwelling infrastructure coaxial distribution system, ensure that the coaxial distribution system is separately grounded. Grounding of the dwelling coaxial infrastructure shall use Listed grounding devices and must be installed in accordance with local Codes and Article 800 of the National Electric Code, ANSI/NFPA 70, following the manufacturers instructions. Warning This equipment is ESD sensitive. Proper ESD protections should be used when removing the fiber access cover of the indoor ONT. Caution Keep indoor ONTs out of direct sunlight. Prolonged exposure to direct sunlight can damage the unit. Procedure Note Observe the following: The indoor ONT should be installed in accordance with the applicable requirements of the NEC or CEC. Local authorities and practices take precedent when there is conflict between the local standard and the NEC or CEC. The indoor ONT must be installed by qualified service personnel. Indoor ONTs must be installed with cables that are suitably rated and listed for indoor use. See the detailed specifications in the I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P detailed specifications for the ONT temperature ranges for these ONTs. Use this procedure to replace an I-240W-P, I-240W-Q, I-240W-R, I-240W-T, or I-241W-P indoor ONT. 1 Deactivate the ONT services (DLP 131). If you are using the SLID feature, this step is not required. The ONT and the services can remain in service (IS). 2 If used, disable the Wi-Fi service (DLP 130). 3 For I-240W-Q, I-240W-R, and I-240W-T ONTs, power down the unit by using the on/off power switch. NTP November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

392 NTP 191 Replace an I-240W-P, I-240W-Q, I-240W-R, I-240W-T, or I-241W-P indoor ONT 4 Disconnect the POTS, Ethernet, coaxial, fiber optic cables (DLP 133), and power cables from the ONT; see Figure NTP for the connector locations on I-240W-P indoor ONT, see Figures NTP and NTP for the connector locations on I-240W-Q, I-240W-R, and I-240W-T indoor ONTs, and Figure NTP for the connector locations on I-241W-P indoor ONTs. Figure NTP 191-1: I-240W-P ONT connections GE POTS Ethernet ports (RJ45) POTS ports (RJ-11) Wi-Fi on/off switch A B WiFi ON OFF Power connector PWR 12VDC GPON 2.5G/1.25G G B+ Class 1 Laser Fiber optic connector (internal) Figure NTP 191-2: I-240W-Q, I-240W-R, and I-240W-T ONT connections (back view) TEL1 TEL2 LAN1 LAN2 LAN3 LAN4 ON/OFF POWER OPTICAL POTS ports (RJ-11) Ethernet ports (RJ-45) Power On/Off switch Power connector Fiber optic connector Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November 2013 NTP FE AAAA TCZZA Edition 01

393 NTP 191 Replace an I-240W-P, I-240W-Q, I-240W-R, I-240W-T, or I-241W-P indoor ONT Figure NTP 191-3: I-240W-Q, I-240W-R, and I-240W-T ONT connections (side view) USB2 USB1 WPS RESET WLAN USB ports Wi-Fi Protected Setup Reset button WLAN button Figure NTP 191-4: I-241W-P ONT connections GE POTS Ethernet ports (RJ45) POTS ports (RJ-11) Wi-Fi on/off switch F-Type coaxial connector A B WiFi ON OFF RF Power connector PWR 12VDC GPON 2.5G/1.25G G B+ Class 1 Laser Fiber optic connector (internal) Replace the ONT with a new unit: a On a flat surface, such as a desk. i ii Wrap the excess optic cable for the new ONT inside the fiber storage tray. Attach the fiber storage tray to the new ONT. NTP November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

394 NTP 191 Replace an I-240W-P, I-240W-Q, I-240W-R, I-240W-T, or I-241W-P indoor ONT iii Substitute the new ONT for the old ONT on a flat surface, horizontally resting on its four feet, as shown in Figures NTP 191-1, NTP 191-2, and NTP Note The I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P ONTs cannot be stacked with another ONT or with other equipment. The ONT mounting requirements are: allow a minimum 100 mm clearance above the top cover allow a minimum 50 mm clearance from the side vents do not place any heat source directly above the top cover or below the bottom cover iv Go to step 6. b On a wall. i ii Slide the old ONT off of the mounting screws until the ONT is free of the wall. Slide the wall mount holes on the ONT enclosure or fiber storage tray of the new ONT over the mounting screws until it is securely seated. 6 Connect the Ethernet cables to the RJ-45 ports (DLP 101). 7 Connect the POTS cables to the RJ-11 ports (DLP 123). 8 For the I-241W-P indoor ONT only, connect the coaxial cable to the F-Type connector (DLP 116). 9 If required, have approved service personnel who are trained to work with optic fiber clean the fiber optic connection. See DLP 134 for more information about fiber optic handling, inspection, and cleaning. Danger Fiber optic cables transmit invisible laser light. To avoid eye damage or blindness, never look directly into fibers, connectors, or adapters. 10 Connect the SC/APC fiber optic cable (DLP 125). Warning Be careful to maintain a bend radius of no less than 1.5 inches (3.8 cm) when connecting the fiber optic cable. Too small of a bend radius in the cable can result in damage to the optic fiber. 11 Install the power supply according to manufacturer specifications. Note Observe the following: Units must be powered by a Listed or CE approved and marked limited power source power supply with a minimum output rate of 12 V dc, 1.25 A. 12 Connect the power cable to the power connector. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November 2013 NTP FE AAAA TCZZA Edition 01

395 NTP 191 Replace an I-240W-P, I-240W-Q, I-240W-R, I-240W-T, or I-241W-P indoor ONT 13 For I-240W-Q, I-240W-R, and I-240W-T ONTs, power up the unit by using the on/off power switch. 14 If used, enable the Wi-Fi service (DLP 130). 15 If used, configure the SLID (DLP 6). Note A new SLID or the old SLID may be used with the replacement ONT. If a new SLID is used, the new SLID must also be programmed at the P-OLT using TL1 or a network manager. If the old SLID is used, no changes need to be made at the P-OLT; see the operations and maintenance documentation for the OLT for more information. 16 Verify the ONT LEDs, voltage status, and optical signal levels (DLP 127). 17 Activate and test the services (DLP 128). 18 If necessary, reset the ONT (DLP 126). 19 STOP. This procedure is complete. NTP November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

396 NTP 192 Configure an I-240W-P, I-240W-Q, I-240W-R, I-240W-T, or I-241W-P indoor ONT General Please refer to the OLT Operations and Maintenance using TL1 and CLI guide for the software configuration procedure for I-240W-P, I-240W-Q, I-240W-R, I-240W-T, and I-241W-P indoor ONTs. For HTTP configuration procedures, please refer to chapter 6, ONT management using an ONT interface. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November 2013 NTP FE AAAA TCZZA Edition 01

397 NTP 192 Configure an I-240W-P, I-240W-Q, I-240W-R, I-240W-T, or I-241W-P indoor ONT NTP November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

398 I-240W-S, I-241W-S, I-241W-U 39 I-240W-S, I-241W-S, and I-241W-U unit data sheet NTP 193 Install an I-240W-S, I-241W-S, or I-241W-U indoor ONT NTP 194 Replace an I-240W-S, I-241W-S, or I-241W-U indoor ONT NTP 195 Configure an I-240W-S, I-241W-S, or I-241W-U indoor ONT Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

399 November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

400 39 I-240W-S, I-241W-S, and I-241W-U unit data sheet 39.1 I-240W-S, I-241W-S, I-241W-U part numbers and identification I-240W-S, I-241W-S, and I-241W-U general description I-240W-S, I-241W-S, and I-241W-U software and installation feature support I-240W-S, I-241W-S, and I-241W-U interfaces and interface capacity I-240W-S, I-241W-S, and I-241W-U LEDs I-240W-S, I-241W-S, and I-241W-U detailed specifications I-240W-S, I-241W-S, and I-241W-U GEM ports and T-CONTs I-240W-S, I-241W-S, and I-241W-U power support I-240W-S, I-241W-S, and I-241W-U functional blocks I-240W-S, I-241W-S, and I-241W-U standards compliance I-240W-S, I-241W-S, and I-241W-U special considerations Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

401 39 I-240W-S, I-241W-S, and I-241W-U unit data sheet 39.1 I-240W-S, I-241W-S, I-241W-U part numbers and identification Table 39-1 provides part numbers and identification information for I-240W-S, I-241W-S, and I-241W-U indoor ONTs. Table 39-1 I-240W-S, I-241W-S, and I-241W-U indoor ONT part numbers and identification Mnemonic Ordering kit part number Provisioning part number Description CLEI CPR ECI/ Bar code I-240W-S 3FE AA 3FE AA 2 POTS ports, 4 Gig-E 10/100/1000 Base-T interfaces, and 1 Wi-Fi radio on/off switch. Includes ac/dc power cord with European (EU) variant plug. 3FE BA 2 POTS ports, 4 Gig-E 10/100/1000 Base-T interfaces, and 1 Wi-Fi radio on/off switch. Includes ac/dc power cord with Australian (AU) variant plug. 3FE CA 2 POTS ports, 4 Gig-E 10/100/1000 Base-T interfaces, and 1 Wi-Fi radio on/off switch. Includes ac/dc power cord with United Kingdom (UK) variant plug. 3FE EA 2 POTS ports, 4 Gig-E 10/100/1000 Base-T interfaces, and 1 Wi-Fi radio on/off switch. Includes ac/dc power cord with United States (US) variant plug. I-241W-S 3FE AA 3FE AB 2 POTS ports, 4 Gig-E 10/100/1000 Base-T interfaces, 1 RF video connector, and 1 Wi-Fi radio on/off switch. Includes ac/dc power cord with European (EU) variant plug. 3FE BA 2 POTS ports, 4 Gig-E 10/100/1000 Base-T interfaces, 1 RF video connector, and 1 Wi-Fi radio on/off switch. Includes ac/dc power cord with Australian (AU) variant plug. 3FE CA 2 POTS ports, 4 Gig-E 10/100/1000 Base-T interfaces, 1 RF video connector, and 1 Wi-Fi radio on/off switch. Includes ac/dc power cord with United Kingdom (UK) variant plug. 3FE EA 2 POTS ports, 4 Gig-E 10/100/1000 Base-T interfaces, 1 RF video connector, and 1 Wi-Fi radio on/off switch. Includes ac/dc power cord with United States (US) variant plug. (1 of 2) 39-2 November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

402 39 I-240W-S, I-241W-S, and I-241W-U unit data sheet Mnemonic Ordering kit part number Provisioning part number Description CLEI CPR ECI/ Bar code I-241W-U 3FE AA 3FE AA 2 POTS ports, 4 Gig-E 10/100/1000 Base-T interfaces, 1 RF video connector, 2 USB ports, and dual-band Wi-Fi radio. Includes ac/dc power cord with European (EU) variant plug. 3FE EA 2 POTS ports, 4 Gig-E 10/100/1000 Base-T interfaces, 1 RF video connector, 2 USB ports, and dual-band Wi-Fi radio. Includes ac/dc power cord with United States (US) variant plug. (2 of 2) 39.2 I-240W-S, I-241W-S, and I-241W-U general description I-240W-S, I-241W-S, and I-241W-U indoor ONTs provide the subscriber interface for the network by terminating the PON interface and converting it to user interfaces that directly connect to subscriber devices. The ONT is compatible with all existing subscriber equipment, including analog phones with both tone and rotary dial capabilities, cordless phones, modems, fax machines, and caller ID boxes (Type I, Type II, and Type III). I-240W-S, I-241W-S, and I-241W-U indoor ONTs provide the following functions: four configurable 10/100/1000BASE-T Ethernet interfaces using RJ-45 ports two POTS interfaces using RJ-11 ports single mode fiber (SC/APC connector) one coaxial RF video connector (I-241W-S only) one coaxial RF video connector and HPNA v3.1 over Coax (I-241W-U only) one USB port (I-240W-S and I-241W-S) two USB 2.0 ports (I-241W-U only) IEEE Wi-Fi interface to enable wireless access 2.4G and 5G dual band concurrent Wi-fi (I-241W-U) fully G.984 series GPON standard compliant G984.5 standard compliant compliance with FCC part 15 Class B supports VPN pass-through for PPTP, L2TP, and IPsec 39.3 I-240W-S, I-241W-S, and I-241W-U software and installation feature support Table 39-2 provides a list of software-based features and installation information supported by I-240W-S, I-241W-S, and I-241W-U indoor ONTs. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

403 39 I-240W-S, I-241W-S, and I-241W-U unit data sheet Table 39-2 I-240W-S and I-241W-S indoor ONT software feature support Feature Chapter/description Click link for more information General ONT and MDU overview Service interface specifications General information common to multiple devices and an explanation of general system behaviors. ONT and MDU general and interface technical specifications ONT and MDU overview Ethernet interface specifications POTS interface specifications RF video interface specifications for video overlay (I-241W-S and I-241W-U only) Services supported See the appropriate P-OLT user documentation for service creation procedures and descriptions. RSSI (1) Wi-Fi specifications Optical budget Location and installation options ONT and MDU general and interface technical specifications ONT and MDU general and interface technical specifications ONT and MDU general and interface technical specifications How to install and replace an I-240W-S, I-241W-S or I-241W-U indoor ONT RSSI specifications Wi-Fi specifications ONT optical budget Install an I-240W-S, I-241W-S, or I-241W-U indoor ONT Replace an I-240W-S, I-241W-S, or I-241W-U indoor ONT Activation methods ONT and MDU overview SLID entry via Ethernet port HTTP management Statistics and performance monitoring Supported UPS configurations Information necessary to manage an ONT at a local site using an HTTP interface, CLI interface, CLI interface, or butt set. ONT and MDU statistics and performance monitoring Part numbers, ordering, and deployment configuration overview Web-based ONT configuration Performance monitoring statistics for Package D ONTs ONT and MDU to UPS or power adapter compatibility support Note (1) I-241W-U indoor ONTs do not support RSSI 39.4 I-240W-S, I-241W-S, and I-241W-U interfaces and interface capacity Table 39-3 describes the supported interfaces and interface capacity for I-240W-S, I-241W-S, and I-241W-U indoor ONTs November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

404 39 I-240W-S, I-241W-S, and I-241W-U unit data sheet Table 39-3 I-240W-S, I-241W-S, and I-241W-U indoor ONT interface connection capacity ONT type and model Maximum capacity POTS 10/ 100 BASE- T 10/ 100/ 1000 BASE- T RF video (CATV) MoCA VDSL2 E1/T1 Local craft GPON SC/ APC HPNA USB I-240W-S (1) I-241W-S (1) I-241W-U (1) Note (1) I-240W-S, I-241W-S, and I-241W-U ONTs provide Wi-Fi service without a physical connection. I-240W-S, I-241W-S, and I-241W-U connections and components I-240W-S, I-241W-S, and I-241W-U indoor ONTs are intended for indoor deployment and can be installed vertically, horizontally, or attached to a wall. Other features of these indoor ONTs include an ON/OFF power switch for manual shut down a reset button an external multi-directional antennae (I-240W-S and I-241W-S only) Wi-Fi service that is enabled and disabled by Web GUI or TR-064/TR-069 a Wi-Fi Protected Setup button Figure 39-1 shows the physical connections for I-240W-S indoor ONTs. Figure 39-1 I-240W-S indoor ONT physical connections I O USB ports Wi-Fi Protected Reset button Service button POTS ports (RJ-11) Ethernet ports (RJ-45) Fiber optic connector Power connector Power on/off switch Figure 39-2 shows the physical connections for I-241W-S indoor ONTs. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

405 39 I-240W-S, I-241W-S, and I-241W-U unit data sheet Figure 39-2 I-241W-S indoor ONT physical connections Reset button Wi-Fi Protected POTS ports Service button (RJ-11) Ethernet ports (RJ-45) Fiber Power optic connector connector Power on/off switch F-type coaxial connector Figure 39-3 shows the physical connections for I-241W-U indoor ONTs. Figure 39-3 I-241W-U indoor ONT physical connections Power WAN GPON Gigabit Ethernet VOIP Link/Act GE4 GE3 GE2 GE1 VOIP2 VOIP1 Wi-Fi 5G Wi-Fi 2.4G WPS 5G WPS 2.4G USB RF Video HPNA USB Reset Button Reset WPS Phone WPS Button POTS ports (RJ-11) Gigabit Ethernet GPON RF Video UPS Power Ethernet ports (RJ45) Fiber optic port Power button Power connector RF Video Figure 39-4 shows the location of the USB host port at the side of I-240W-S ONTs November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

406 39 I-240W-S, I-241W-S, and I-241W-U unit data sheet Figure 39-4 I-240W-S indoor ONT physical connections (USB host port) Internet/ USB host port I O Figure 39-5 shows the location of the USB port on the I-241W-S indoor ONTs. Figure 39-5 I-241W-S indoor ONT physical connections (USB host port) USB port Figure 39-3 shows the location of the USB port on the I-241W-U indoor ONTs. Table 39-4 describes the physical connections for I-240W-S, I-241W-S, and I-241W-U indoor ONTs. Table 39-4 I-240W-S, I-241W-S, and I-241W-U indoor ONT physical connections Connection (1) Ethernet ports Description This connection is provided through Ethernet RJ-45 cables. Up to four 10/100/1000 Base-T Ethernet interfaces are supported.the Ethernet ports can support both data and in-band video services on all four interfaces. (1 of 2) Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

407 39 I-240W-S, I-241W-S, and I-241W-U unit data sheet Connection (1) POTS WPS button RF video coaxial Power Fiber optic USB ports Description This connection is provided through RJ-11 ports. Up to two POTS connections are supported.the POTS ports support voice services. The Wi-Fi Protected Setup switch is labelled WPS. This button enables and disables the WPS mode. This connection is provided through a F-Type coaxial connector. This connection is found only on the I-241W-S and I-241W-U indoor ONTs. For the I-241W-U it also supports HPNA v3.1 over Coax. This connection is provided through the power connector. A power cable fitted with a Molex connector is used to make the connection. This connection is provided through a GPON SC/APC fiber optic connector. On I-240W-S indoor ONTs, this connection is provided through the following USB ports: Two USB host interfaces, compliant to USB 2.0, are supported (one of the USB ports is not powered). One USB host port, compliant to USB 2.0, with a Motive dongle. On I-241W-S indoor ONTs, this connection is provided by one USB host port, compliant to USB 2.0. On I-241W-U indoor ONTs, this connection is provided by two USB host ports, compliant to USB 2.0. Cables with A-type connectors are used to connect to the USB ports. (2 of 2) Note (1) The primary path for the earth ground for these ONTs is provided by the 12V Return signal in the power connector I-240W-S, I-241W-S, and I-241W-U LEDs Figure 39-6 shows the I-240W-S and I-241W-S indoor ONT LEDs. Figure 39-6 I-240W-S and I-241W-S indoor ONT LEDs Gigabit VoIP GPON Ethernet Power WAN Link/Act Wi-Fi WPS USB Gigabit VoIP GPON Ethernet Power WAN Link/Act Wi-Fi WPS USB November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

408 39 I-240W-S, I-241W-S, and I-241W-U unit data sheet Figure 39-7 shows the I-241W-U indoor ONT LEDs. Figure 39-7 I-241W-U indoor ONT LEDs Power WAN GPON Link/Act Gigabit Ethernet VOIP GE4 GE3 GE2 GE1 VOIP2 VOIP1 Wi-Fi 5G Wi-Fi 2.4G WPS 5G WPS 2.4G USB RF Video HPNA Power WAN GPON Gigabit Ethernet VOIP Link/Act GE4 GE3 GE2 GE1 VOIP2 VOIP1 Wi-Fi 5G Wi-Fi 2.4G WPS 5G WPS 2.4G USB RF Video HPNA Reset WPS Phone Gigabit Ethernet GPON RF Video UPS Power Table 39-5 provides LED descriptions for I-240W-S, I-241W-S, and I-241W-U indoor ONTs. Table 39-5 I-240W-S, I-241W-S, and I-241W-U indoor ONT LEDs Indicator LED color and behavior LED behavior description Power WAN GPON Link/Act (1 of 2) Off Green solid Off Green flashing Green solid Red Red solid Red flash Green solid Orange flash Orange solid Power is off Power is on Broadband physical connection is not present or no IP address assigned IP connected and IP traffic is passing IP connected and no traffic passing Device attempted IP connection and failed No GPON signal detected GPON signal detected and ranging GPON connection is up and in-service OMCI data going through GPON port GPON connection is up but out-of-service Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

409 39 I-240W-S, I-241W-S, and I-241W-U unit data sheet Indicator LED color and behavior LED behavior description Gigabit Ethernet VoIP (without VoIP registration status) VoIP (with VoIP registration status) Wi-Fi WPS (I-240W-S and I-241W-S) WPS (I-241W-U) USB Off Green flashing Green solid Off Green solid Off Green solid Green flashing Off Green flashing Green solid Off Green solid Green flashing Red solid Green solid Red solid Off Green flashing Green solid No Ethernet signal detected User data going through Gigabit Ethernet port Gigabit Ethernet interface is ready to work Phone is on-hook Phone is off-hook VoIP is unregistered VoIP is registered and phone is on-hook VoIP is registered and phone is off-hook No radio signal detected User data going through WLAN port Wi-Fi interface is ready to work Inactive Success status In Progress status Error and Session Overlap status In Progress or Success status Error and Session Overlap status No USB signal detected Traffic activity on the USB port At least one device which is not a USB hub is connected to the USB port I-241W-S and I-241W-U indoor ONT only RF Video Off Green RF is disabled or the video optical band being received is lower than the prescribed limit RF is enabled and optical signal power is working I-241W-U indoor ONT only HPNA (2 of 2) Off Green flashing Green solid HPNA not connected Traffic activity on the HPNA port HPNA is connected 39.6 I-240W-S, I-241W-S, and I-241W-U detailed specifications Table 39-6 lists the physical specifications for I-240W-S, I-241W-S, and I-241W-U indoor ONTs. Table 39-6 I-240W-S, I-241W-S, and I-241W-U indoor ONT physical specifications Description Height Width Depth Specification 8.9 in. (22.5 cm) 6.5 in. (16.6 cm) 1.7 in. (4.3 cm) (1 of 2) November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

410 39 I-240W-S, I-241W-S, and I-241W-U unit data sheet Description I-240W-S weight including fiber storage tray [within ± 0.5 lb (0.23 kg)] I-241W-S weight including fiber storage tray [within ± 0.5 lb (0.23 kg)] I-241W-U weight including fiber storage tray [within ± 0.5 lb (0.23 kg)] Specification 1.64 lb (743 g) 1.7 lb (773 g) 1.55 lb (702 g) (2 of 2) Table 39-7 lists the power consumption specifications for I-240W-S, I-241W-S, and I-241W-U indoor ONTs. Table 39-7 I-240W-S, I-241W-S, and I-241W-U indoor ONT power consumption specifications Mnemonic Maximum power (Not to exceed) Condition Minimum power Condition I-240W-S less than 30 W 2 POTS off-hook, 4 Gig-E, Wi-Fi operational I-241W-S less than 24 W 2 POTS off-hook, 4 Gig-E, 1 RF video, Wi-Fi operational I-241W-U less than 30 W 2 POTS off-hook, 4 Gig-E, 1 RF video, Wi-Fi operational 6.3 W 2 POTS on-hook, other interfaces/services not provisioned 7.7 W 2 POTS on-hook, other interfaces/services not provisioned 8.6 W 2 POTS on-hook, other interfaces/services not provisioned Table 39-8 lists the environmental specifications for I-240W-S, I-241W-S, and I-241W-U indoor ONTs. Table 39-8 I-240W-S and I-241W-S indoor ONT environmental specifications Mounting method Temperature range and humidity Altitude I-240W-S and I-241W-S Desk or wall mounted I-241W-U (1 of 2) Operating: (1) -4 F to 122 F (-20 C to 50 C) ambient temperature 20% to 90% relative humidity, non-condensing Storage: Contact your Alcatel-Lucent support representative for more information Contact your Alcatel-Lucent technical support representative for more information Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

411 39 I-240W-S, I-241W-S, and I-241W-U unit data sheet Mounting method Temperature range and humidity Altitude Desk or wall mounted (2 of 2) Operating: 23 F to 104 F (-5 C to 40 C) ambient temperature 8% to 95% relative humidity, non-condensing Maximum rate of temperature change is 108 F (60 C) per hour Storage: -40 F to 149 F (-40 C to 65 C) 8% to 95% relative humidity, non-condensing Contact your Alcatel-Lucent technical support representative for more information Note (1) When an I-240W-S ONT is used with a power adapter, the maximum operating temperature is 122 F (50 C) while the maximum temperature for an I-240W-S ONT used with an uninterrupted power supply (UPS) is 104 F (40 C) I-240W-S, I-241W-S, and I-241W-U GEM ports and T-CONTs Table 39-9 lists the maximum number of supported T-CONTs and GEM ports. Not all ONTs will be supported in all of the releases indicated the table. See the appropriate release Customer Release Notes for the most accurate list of supported devices. Table 39-9 I-240W-S, I-241W-S, and I-241W-U indoor ONT capacity for GEM ports and T-CONTs per package and release ONT or MDU Release Maximum Notes Package D ONTs GEM ports per indoor or outdoor ONT R are present: 31 are available, 1 is reserved for OMCI R are present: 127 are available, 1 is reserved for OMCI T-CONTs per indoor or outdoor ONT R R I-240W-S, I-241W-S, and I-241W-U power support I-240W-S and I-241W-S indoor ONTs support the following power supply: CyberPower CyberShield CSN27U12V UPS unit data sheet I-241W-U indoor ONTs support the following power supply: Delta DUPS-1232G UPS unit data sheet November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

412 39 I-240W-S, I-241W-S, and I-241W-U unit data sheet 39.9 I-240W-S, I-241W-S, and I-241W-U functional blocks Table describes the supported interfaces for I-240W-S, I-241W-S, and I-241W-U indoor ONTs. Table I-240W-S, I-241W-S, and I-241W-U indoor ONT interfaces ONT category description Interface capacity POTS ports Ethernet ports VDSL2 MoCA RF Video HPNA Wi-Fi USB Single-residence Wi-Fi ONTs with Gig-E ONTs, POTS, and with or without RF video (I-240W-S, I-241W-S) Single-residence Wi-Fi ONTs with Gig-E ONTs, POTS, and with or without RF video and with HPNA (I-241W-U) 2 4 0/1 1 1/ I-240W-S, I-241W-S, and I-241W-U indoor ONTs are single-residence ONTs that support Wireless (Wi-Fi) service. Wi-Fi service on these ONTs are compliant with the IEEE standard and enabled or disabled using a radio on/off switch. In addition to the Wi-Fi service, these ONTs transmit Ethernet packets to four RJ-45 Ethernet ports, and voice traffic to two RJ-11 POTS ports. These ONTs have USB ports also. The I-240W-S and I-241W-S have one USB connector, while the I-241W-U has two USB2.0 connectors. The I-241W-S ONT also supports RF video traffic on one F-type coaxial connector. The I-241W-U ONT supports RF video and HPNA traffic on one F-type coaxial connector. Both ONTs feature fiber optic and power connectors. Figure 39-8 shows functional blocks for I-240W-S indoor ONTs. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

413 39 I-240W-S, I-241W-S, and I-241W-U unit data sheet Figure 39-8 Single-residence Wi-Fi ONT with Gigabit Ethernet and POTS and without RF video Diplexer USB Internal Host GPON SOC RESET External USB Host POTS GE PHY switch 2xUSB 2xRJ11 4xRJ45 PWR Figure 39-9 shows functional blocks for the I-241W-S and I-241W-U indoor ONT which have the same functional blocks as the I-240W-S indoor ONT except for having a triplexer, rather than a diplexer, and an RF video or HPNA filter. The I-241W-S has one external USB port, while the I-241W-U has two. Figure 39-9 Single-residence Wi-Fi ONT with Gigabit Ethernet and POTS and with RF video Triplexer RF or HPNA filter F-type connector Internal USB host GPON SOC RESET External USB Host POTS GE PHY switch 2xUSB 2xRJ11 4xRJ45 PWR ONT SoC technology serves as the main hardware block for these ONTs; see Figure November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

414 39 I-240W-S, I-241W-S, and I-241W-U unit data sheet Figure I-240W-S, I-241W-S, and I-241W-U ONT hardware block POTS ports Control processor SoC DSP SoC Bridge Ethernet MACs GPON MAC Ethernet ports GPON ONT SoC technology consists of five key elements: GPON MAC The Gigabit Passive Optical Network Media Access Control (GPON MAC) element on the SoC terminates the GPON interface using an optical diplexer. This interface supports GPON as described in G (GPON TC Layer) ITU specification. Ethernet MAC The SoC provides up to four GE MACs. DSP interface The Digital Signal Processor (DSP) provides voice processing for 2 POTS lines with the 3-way calling. The DSP has a dedicated 64 kbyte instruction cache and shares a 32 kbyte data cache with the Control Processor. Control Processor The Control Processor features an integral memory management unit that supports a dedicated 64 kbyte instruction cache and shares a single 32 kbyte data cache with the DSP. The Control Processor and DSP also include a single channel Data Management Application (DMA) controller with a 4 kbyte read ahead low-latency Dynamic Random Access Memory (DRAM) access port. The processors typically run at 400 MHz. Switch matrix The Switch matrix provides an integrated data channel between the four GE MACs, the GPON MAC, the DSP, the control processor, and the other integrated elements such as flash memory, DRAM, and the local bus controller. These ONTs can also interact with additional hardware components to support functionality not provided by the SoC technology. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

415 39 I-240W-S, I-241W-S, and I-241W-U unit data sheet I-240W-S, I-241W-S, and I-241W-U standards compliance I-240W-S, I-241W-S, and I-241W-U indoor ONTs are compliant with the following standards: b support for maximum transmit power (EIRP) equal to or greater than 200 mw (23.01 dbm) g support for maximum transmit power (EIRP) equal to or greater than 100 mw (20 dbm) n support for wireless LAN interface G.984 support GPON interface (framing) G support for Amd1, class B+ G984.5 support for optical and other transport network infrastructures UPnP compliance (I-241W-U) DLNA compliance (I-241W-U) HPNA compliance (I-241W-U) I-240W-S, I-241W-S, and I-241W-U special considerations I-240W-S, I-241W-S, and I-241W-U indoor ONT considerations and limitations Table lists the considerations and limitations for I-240W-S, I-241W-S, and I-241W-U ONTs. Table I-240W-S, I-241W-S, and I-241W-U ONT considerations and limitations Considerations and limitations Performance Counters for SIP Voice is not supported Emergency call alarming is not supported by H.248 No support for IGMP on PPPoE sessions No support for MAC learning Upgrade considerations and limitations Existing ONTs that use 7342 ISAM FTTU releases older than R04.06.xx and R04.07.xx must be upgraded to use R software while assigned to a PON ID value smaller than 64. For this purpose, if split ratios larger than 1:64 are being deployed, you may choose to set aside the first PON ID as a staging point. I-240W-S, I-241W-S, and I-241W-U indoor ONTs support voice, video, and data services. These ONTs, which feature Wi-Fi technology, can also function as a residential gateway with layer 2 and layer 3 processing capabilities November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

416 39 I-240W-S, I-241W-S, and I-241W-U unit data sheet I-240W-S, I-241W-S, and I-241W-U ONT supported features The I-240W-S, I-241W-S, and I-241W-U ONT supports one of two modes at any given time. The supported modes are ONT Residential gateway You determine which of the two modes is configured using TR-069. Set the parameter InternetGatewayDevice.LANDevice.{i}.LANEthernetInterfaceConfig.{i}.X_ALU_COM_BridgeMode to TRUE for bridge (ONT) mode or to FALSE for routing (RG) mode. ONT mode When operating in ONT mode, I-240W-S and I-241W-S ONTs have four Gig-E and two POTS ports while the Wi-Fi service and USB modules are disabled. I-240W-S, I-241W-S, and I-241W-U indoor ONTs support the following services controlled by OLT: VoIP L2 bridging Multicast Table describes the services supported by I-240W-S, I-241W-S, and I-241W-U indoor ONTs when in ONT mode. Table Supported services in ONT mode Supported services VoIP Description The IP host interface is dedicated for VoIP service The SIP protocol (RFC3261) is ported to the ONT. VoIP-related parameters are configured through the OMCI protocol and downloading the VoIP XML file to the ONT. See VoIP overview for details about the XML download files. The MEGACO v2 (H.248) protocol is supported by the ONT. (1 of 2) Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

417 39 I-240W-S, I-241W-S, and I-241W-U unit data sheet Supported services L2 bridging Multicast Description Each Ethernet port supports the following VLAN tagging VLAN/p-bit transparent VLAN/p-bit translation The following OLT VLAN modes are supported for 7342 ISAM FTTU: XCONN - Cross-connect RBRIDGE - Residential Bridge (default) CVLANLEARN - C-VLAN Learning Mode (not supported by the GLT2-A/B/C) MIRROR - Mirroring Mode The following OLT VLAN modes are supported for 7302 ISAM, 7330 ISAM FTTN, and 7360 ISAM FX: C-VLAN cross-connect S+C-VLAN cross-connect S-VLAN tunnel cross-connect C-VLAN residential-bridge IGMP snooping 64 multicast groups (2 of 2) Residential gateway ONT mode When operating in Residential gateway ONT mode, I-240W-S, I-241W-S, and I-241W-U ONTs have one virtual Ethernet IP and two POTS ports. I-240W-S, I-241W-S, and I-241W-U indoor ONTs support the following services: VoIP L3 routing Residential gateway interfaces Multicast VoIP service is controlled by OMCI while OLT is reserved for configuring L2 bridging and Multicast services for the L3 routing interface. Established L3 routing can be managed using Access Control Server (ACS). Table describes the services supported by I-240W-S, I-241W-S, and I-241W-U indoor ONTs in Residential gateway mode. Table Supported services in Residential gateway ONT mode Supported services VoIP Description The IP host interface is dedicated for VoIP service The SIP protocol (RFC3261) is ported to the ONT. VoIP-related parameters are configured through the OMCI protocol and downloading the VoIP XML file to the ONT. See VoIP overview for details about the XML download files. (1 of 2) November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

418 39 I-240W-S, I-241W-S, and I-241W-U unit data sheet Supported services L3 routing Description Each Ethernet port supports the following VLAN tagging VLAN/p-bit transparent VLAN/p-bit translation OLT must be used to configure the VLAN/p-bit used by the following services: HSI IPTV including VoD and Multicast service Management After the OLT has configured the L2 bridging path for the L3 routing interface, the Residential gateway service can be controlled remotely by ACS using the TR-069 protocol. Residential gateway interfaces Both LAN and WAN connections are provided. On the up to four WAN connections on the WAN side the following services are provided HSI internet service IPTV including VoD and Multicast service TR-069 remote management VoIP (ACS-controlled VoIP service) Only the HSI and IPTV interfaces are used for routing services for LAN devices. The traffic on other interfaces terminates at the ONT. IPoE and PPPoE can be configured for each interface with the exception of the IPTV interface which does not support the PPPoE mode. On the two LAN connections the following services are provided Home network interface is the main interface includes four Ethernet ports, one Wi-Fi AP, and one USB interface. All of these interfaces are bridged. The user on this interface can access HSI and IPTV services. From the LAN side, web GUIs and TR-064 are used to manage the ONT. UPnP IGD and DLNA services are not supported on this interface. Guest network interface is an extra LAN interface with only one Wi-Fi AP attached. Guests can access HSI and IPTV services but can not access the ONT management interface. UPnP IGD and DLNA services are not supported on this interface. Multicast IGMP snooping for home network interface IGMP proxy for WAN IPTV interface Multicast service is not supported on the guest network interface (2 of 2) Wi-Fi service I-240W-S, I-241W-S, and I-241W-U indoor ONTs feature Wi-Fi service as well as voice, video, and data services. Wi-Fi is a wireless networking technology that uses radio waves to provide wireless HSI and network connections. This ONT complies with the IEEE standards, which the Wi-Fi Alliance defines as the basis for Wi-Fi technology. The I-241W-U indoor ONT supports dual-band Wi-Fi at 2.4 GHz and 5GHz. Wi-Fi physical features I-240W-S and I-241W-S indoor ONTs have one external multi-directional antennae. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

419 39 I-240W-S, I-241W-S, and I-241W-U unit data sheet The I-240W-S, I-241W-S, and I-241W-U indoor ONTs provide a Wi-Fi Protected Setup (WPS) push button, with indicator LED, for adding WPS-enabled wireless devices. Wi-Fi standards, certifications and services The Wi-Fi service on I-240W-S, I-241W-S, and I-241W-U indoor ONTs support the following standards and Wi-Fi Alliance certifications: compliant with IEEE 802.1x EAP encapsulation certified for IEEE b/g/n standards multiple SSID and WDS WEP, WPA, and WPA2 MAC address filtering ONT management features I-240W-S, I-241W-S, and I-241W-U indoor ONTs support management using the following methods: Web GUI using HTTP OMCI interface VoIP xml TR-069 Contact your Alcatel-Lucent technical support representative for more information about ONT management for I-240W-S, I-241W-S, and I-241W-U indoor ONTs. Web-based ONT configuration I-240W-S, I-241W-S, and I-241W-U indoor ONTs support limited configuration using a web-based GUI. The following types of configuration and information retrieval procedures can be performed using the GUI: supported device information supported ONT information supported RGW supported VoIP supported diagnosis supported management Supported Device information I-240W-S, I-241W-S, and I-241W-U indoor ONTs support limited retrieval of supported device information using a web-based GUI. The following status information can be retrieved using a GUI: General status Transceiver status UPS status November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

420 39 I-240W-S, I-241W-S, and I-241W-U unit data sheet Procedure 39-1 General status information retrieval 1 Select Device Info from the top-level menu in the GPON Web-Management System window. 2 Select the General Status option from the Device Info menu. The Device Information -> General Status window appears; see Figure Figure General Status window Table describes the fields in the General Status window. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

421 39 I-240W-S, I-241W-S, and I-241W-U unit data sheet Table General Status parameters Field Software Version Hardware Version System Time Uptime Board ID Build Timestamp Boatloader (CFE) Version Wireless Driver Version Description Identifying the software version currently. Example: 3FE54278AOAA18 A string identifying the particular CPE model and version. Example: REV1.0 The current date and time in the CPE Time since the CPE was last restarted Board ID of the CPE Build date and time of the current software Identifying the software version currently. Example: A string identifying the particular wireless driver version. Example: cpe4.11L STOP. This procedure is complete. Procedure 39-2 Transceiver status information retrieval 1 Select Device Info from the top-level menu in the GPON Web-Management System window. 2 Select the Transceiver Status option from the Device Info menu. The Device Information -> Transceiver Status and Threshold window appears; see Figure November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

422 39 I-240W-S, I-241W-S, and I-241W-U unit data sheet Figure Transceiver Status and Threshold window Table describes the fields in the Transceiver Status and Threshold window. Table Transceiver Status and Threshold parameters Field Temperature RX Power TX Power Voltage Description Current temperature of the CPE. The unit is degree centigrade (C). Current RX power of the CPE. The unit is dbm. Current TX power of the CPE. The unit is dbm. Current voltage of the CPE 3 STOP. This procedure is complete. Procedure 39-3 UPS status information retrieval 1 Select Device Info from the top-level menu in the GPON Web-Management System window. 2 Select the UPS Status option from the Device Info menu. The Device Information -> UPS Status window appears; see Figure Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

423 39 I-240W-S, I-241W-S, and I-241W-U unit data sheet Figure UPS Status window Table describes the fields in the UPS Status window. Table UPS status parameters Field Status Description Show current UPS status of the CPE 3 STOP. This procedure is complete. Supported ONT information I-240W-S, I-241W-S, and I-241W-U indoor ONTs support limited retrieval of supported ONT information using a web-based GUI. The following status information can be retrieved using a GUI: GPON Multicasting IP Host VEIP November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

424 39 I-240W-S, I-241W-S, and I-241W-U unit data sheet Procedure 39-4 GPON status information retrieval 1 Select ONT from the top-level menu in the GPON Web-Management System window. 2 Select the GPON option from the ONT menu. The ONT -> GPON window appears; see Figure Figure GPON window Table describes the fields in the GPON window displayed below the Serial Number. Table GPON parameters Field Password (ASCII) Password (hex) Description Set GPON password with ASCII characters Set GPON password with hexadecimal characters 3 Click Apply/Save. See the GPON Status, Mapping, and Statistics information in the window. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

425 39 I-240W-S, I-241W-S, and I-241W-U unit data sheet 4 Click Refresh to update the GPON status, mapping, and statistics information in the window. 5 STOP. This procedure is complete. Procedure 39-5 Multicasting status information retrieval 1 Select the ONT option from the top-level menu in the GPON Web-Management System window. 2 Select the Multicasting option from the ONT menu. The ONT -> Multicasting window appears; see Figure Figure Multicasting window Table describes the fields in the Multicasting window November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

426 39 I-240W-S, I-241W-S, and I-241W-U unit data sheet Table Multicasting parameters Field Status Description Index and active group ID information is displayed. 3 STOP. This procedure is complete. Procedure 39-6 IP Host information retrieval 1 Select ONT from the top-level menu in the GPON Web-Management System window. 2 Select the IP Host option from the ONT menu. The ONT -> IP Host window appears; see Figure Figure IP Host window Table describes the fields in the IP Host window. Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

427 39 I-240W-S, I-241W-S, and I-241W-U unit data sheet Table IP Host parameters Field IP address Subnet Mask Gateway DNS Server Mode RX Statistics TX Statistics Description Current IP address of IP host Current subnet mask of IP host Current Gateway of IP host Current DNS Server of IP host Current addressing mode of IP host RX statistics of IP host TX statistics of IP host 3 STOP. This procedure is complete. Procedure 39-7 VEIP status information retrieval 1 Select ONT from the top-level menu in the GPON Web-Management System window. 2 Select the VEIP option from the ONT menu. The ONT -> VEIP window appears; see Figure November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

428 39 I-240W-S, I-241W-S, and I-241W-U unit data sheet Figure VEIP window Table describes the fields in the VEIP window. Table VEIP parameters Field RX Statistics TX Statistics Description RX statistics of VEIP TX statistics of VEIP 3 STOP. This procedure is complete. Supported Residential Gateway (RGW) configuration - WAN I-240W-S, I-241W-S, and I-241W-U indoor ONTs support limited configuration of RGW service using a web-based GUI. The following WAN IPv4 and IPv6 tasks can be performed using the following GUI procedures: add WAN PPPoE service (IPv4) add WAN IPoE service (IPv4) remove WAN connection (IPv4) retrieve IPv6-related WAN connection information Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01

429 39 I-240W-S, I-241W-S, and I-241W-U unit data sheet Procedure 39-8 Add WAN PPPoE service 1 Select the RGW option from the top-level menu in the GPON Web-Management System window. 2 Select the WAN and IPv4 options from the RGW menu. The RGW -> WAN -> IPv4 window appears; see Figure Figure WAN IPv4 window 3 Configure PPPoE by clicking Add. The WAN Service Configuration window appears; see Figure November 2013 Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R Edition 01 3FE AAAA TCZZA

430 39 I-240W-S, I-241W-S, and I-241W-U unit data sheet Figure WAN Service Configuration window 4 Configure the parameters for the PPPoE service. Table describes the fields to select for the PPPoE service. Table PPPoE service parameters Field Description Select WAN Connection type: PPP over Ethernet (PPPoE) IP over Ethernet (IPoE) Select for PPPoE service Select for IPoE service Service Type: (Multiple selections are possible) HSI VoIP Management Select to provide High Speed Internet Select to provide VoIP service (not supported) Select to provide TR-069 remote management Other fields Enter Service Description Enter 802.1P Priority [0-7] Enter a description of the WAN service Enter the priority which is used on egress traffic from this WAN. The value will be ignored when the option Enable DSCP to P-bit for this connection is checked. (1 of 2) Alcatel-Lucent 7302 ISAM 7330 ISAM FTTN 7360 ISAM FX ONT R November FE AAAA TCZZA Edition 01