WNC1800/ZFR182x Pro Series Wireless Field Bus System

Transcription

1 WNC1800/ZFR182x Pro Series Wireless Field Bus System Product Bulletin Code No. LIT Issued February 2017 The WNC1800/ZFR182x Pro (ZFR Pro) Series Wireless Field Bus System provides a wireless platform for all Metasys Field Equipment Controller (FEC) and select TEC3000 Thermostat Controllers (TEC) family controllers using BACnet protocol over the 2.4 GHz wireless ISM band. The pairing of a ZFR1821 or ZFR1822 Pro Router and any FEC family device, or a wireless TEC3000 model (with built-in router), are referred to as Wireless- Enabled Field Controllers (WEFCs). An FEC family device is an Advanced Application Field Equipment Controller (FAC), FEC, Input/Output Module (IOM), or VAV Modular Assembly 16 Series (VMA16) field controller. A ZFR Pro Series system consists of: Wireless Network Coordinators (WNC) Gateways ZFR1820 or ZFR1823 Pro Coordinator Radios TEC3000 Wireless Thermostat Controllers ZFR1821 or ZFR1822 Pro Router connected to FEC Family devices or acting as repeaters WRZ Series Wireless Room Sensors Note: Repeaters extend the wireless transmission distance of the BACnet data communications, fill in any gaps within the wireless mesh network, and provide alternate wireless data transmission pathways. Table 1: Features and Benefits (Part 1 of 2) Features Benefits Wireless Communications for a Metasys System Wireless Mesh Network Improved Application Mobility and Flexibility Refer to the QuickLIT website for the most up-to-date version of this document. Figure 1: WNC1800/ZFR182x Pro Series Components Together, these components create a wireless mesh network that allows the exchange of data between the collection of WNC Gateways, WEFCs, TEC3000s, and WRZs within the ZFR Pro Series system s wireless network and a network engine using standard BACnet IP communications. The wireless mesh network enhances reliability by providing redundant transmission paths for the data through other routers in the mesh network. The result is a resilient, self-healing network. Provide a wireless platform for Metasys BACnet devices across multiple levels of a Metasys Building Automation System (BAS), from supervisory engines to field controllers to room sensors; enable wireless devices to coexist with hard-wired devices on the same Metasys engine; offer simple add-on hardware to seamlessly enable standard Metasys BACnet field controllers to function wirelessly. Enables quick, economical, and low-maintenance installation; minimizes MS/TP BACnet hardwiring; and enhances reliability through automatically forming wireless links and redundant wireless data transmission paths. Provides a wireless alternative to hard-wired counterparts; facilitates easy initial location and relocation with minimal disruption to building occupants; and cost-effectively extends Metasys systems to applications where building aesthetics (such as solid walls or ceilings, temporary walls, or decorative surfaces) normally hinder hardwiring. WNC1800/ZFR182x Pro Series Wireless Field Bus System Product Bulletin 1

2 Table 1: Features and Benefits (Part 2 of 2) Benefits Features Support of up to Nine WRZ Series Wireless Room Sensors per Wirelessly Enabled Field Controller Multiple Diagnostic Light-Emitting Diodes (LEDs) and display icons Compact, Easy-to-Install, and Versatile ZFR1821/ZFR1822 Pro Routers Naming Conventions in this Document The ZFR Pro Wireless Field Bus system is separate from the existing ZFR Wireless Field Bus System. The following table describes naming conventions used with the new system. Facilitates averaging and high/low selection to optimize comfort in larger zones. Installs easily; provides room temperature, setpoint temperature, occupancy status, and low battery status information to a Metasys system; offers extensive battery life of up to 5 years. Provide quick and easy visual indication of power, FC bus activity, wireless activity, wireless signal strength, and fault conditions; help locate optimum device positions during installation and aid in troubleshooting. Adapt easily to multiple mounting scenarios; serve multiple functions, including providing wireless interface for numerous Metasys FEC, IOM, and VMA16 controllers; and function as repeaters to extend wireless transmission range. Table 2: ZFR Pro Part Number Full Name Short Name Various WNC1800/ZFR182x Pro Series Wireless Field Bus System ZFR Pro Series Wireless Field Bus System WNC1800 Wireless Network Coordinator (WNC) Gateway WNC Gateway ZFR1820/ZFR1823 ZFR1820 or ZFR1823 Pro Coordinator Radio ZFR Pro Coordinator Radio ZFR1821/ZFR1822 ZFR1821 or ZFR1822 Pro Wireless Router ZFR Pro Router TEC30xx TEC3000 Series Thermostat Controllers ZFR Pro Thermostats WRZxxxx WRZ Series Wireless Room Sensors ZFR/ZFR Pro Sensors Applications IMPORTANT: Use the ZFR Pro Wireless Field Bus System only to provide an input to equipment under normal operating conditions. Where failure or malfunction of the sensor could lead to personal injury or property damage to the controlled equipment or other property, additional precautions must be designed into the control system. Incorporate and maintain other devices, such as supervisory or alarm systems or safety or limit controls, intended to warn of or protect against failure or malfunction of the ZFR Pro Wireless Field Bus System. The wireless Metasys products within a Metasys system are ideal for any location where it is cost-prohibitive, difficult, or aesthetically unappealing to hardwire between Metasys products. Examples of these locations include the following: hospitals, office buildings, university campuses, educational facilities, correctional facilities, and other commercial structures with brick or solid concrete walls and/or ceilings that impede hard-wired applications office buildings, retail stores, and other commercial real estate where tenant turnover is frequent and temporary walls and ceilings are common museums, historical buildings, atriums, and other sites where building aesthetics and historical preservation are important stadiums, arenas, gymnasiums, convention centers, airports, zoos, and other locations with large, open spaces buildings with marble, granite, glass, mirrored, wood veneer, or other decorative surfaces that present challenges to hardwiring buildings with asbestos or other hazardous materials that must not be disturbed 2

3 buildings with occupants sensitive to disruptions to business regions with high labor costs The ZFR Pro Series System is approved by national compliance agencies for use only in the United States and Canada. See Technical Specifications. Applications to Avoid IMPORTANT: A Network Engine reports an offline alarm within a certain period of time when an associated WEFC goes offline. For a hard-wired FAC, FEC, IOM, or VMA16 device, this time period is a nominal 20 seconds. For WEFCs within the ZFR Pro Wireless Field Bus System, this time period is 5 minutes. Locations or applications that prohibit cellular telephones or Wi-Fi systems are unsuitable for the wireless Metasys products. Examples include: operating rooms or radiation therapy rooms validated environments UL 864 applications Department of Defense applications requiring DIACAP certification (for example, military bases and military hospitals) Do not use the wireless Metasys products in applications that cannot tolerate intermittent interference, or where: critical control features would impact life-safety or result in large monetary loss, including secondary (backup) life-safety applications data centers, production lines, or critical areas would be shut down loss of critical control would result from loss of data from humidity or temperature sensor communications operation of exhaust fans or Air Handling Units (AHUs) would impair a purge or pressurization mode missing data would invalidate reporting required by the customer security points are monitored System Overview Figure 2 illustrates a simple ZFR Pro Wireless Field Bus System applied to BACnet field controllers on a Metasys network. These devices provide wireless monitoring and control of HVAC equipment within multiple levels of a Metasys BACnet system. Refer to the WNC1800/ZFR182x Pro Series Wireless Remote Field Bus System Technical Bulletin (LIT ) for information on commissioning and configuring a ZFR Pro Wireless Field Bus System for operation. The MS/TP trunk and device limits for supported NAE35/45/55 models are the same for hard-wired devices, wireless devices, or a combination of hardwired and wireless devices. For more information, refer to the WNC1800/ZFR182x Pro Series Wireless Field Bus System Technical Bulletin (LIT ). For information on device quantity limits in a ZFR Pro Wireless Field Bus System, see Table 3. Table 3: ZFR Pro Series Wireless Field Bus System Device Quantity Limits Device Quantity Limit WNC Gateway ZFR1821 or ZFR1822 Pro Router Paired with a WEFC. Or a Wireless TEC3000. ZFR1821 or ZFR1822 Pro Router Used as Repeaters WRZ Series Sensor Component Descriptions Up to eight for each Network Engine (NAE Dependent) Up to 35 WEFCs for each WNC Gateway. Up to 100 for each Network Engine, depending on the network engine (50 with NAE35). Unlimited 1 Up to nine sensors per wireless-enabled field controller (Not supported on TEC3000s) 1. Indiscriminate use of ZFR1821 Pro Routers as repeaters can lead to reduced performance. Network Automation Engine (NAE) NAEs are web-enabled, Ethernet-based controllers that monitor and supervise networks of field-level building automation devices that typically control HVAC equipment, lighting, security, fire, and building access. NAEs provide features, including alarm and event management, trending, archiving, energy management, scheduling, and password protection through the embedded Site Management Portal UI. Different models and options support various communications protocols including BACnet over IP, BACnet Master-Slave/Token-Passing (MS/TP), N2 Bus, N2 over Ethernet, and LONWORKS protocol. 3

4 WNC Gateway with ZFR1820 or ZFR1823 Pro Coordinator Radio A WNC Gateway is used in conjunction with a ZFR1820 or ZFR1823 Pro Coordinator radio. The pro coordinator radio provides a wireless interface between an NxE supervisory controller on a wired BACnet IP network and WEFCs. Each wireless mesh network requires one WNC Gateway, which initiates the formation of the network. Each NAE can support up to eight WNC Gateways. A WNC Gateway can operate from either of two power sources when using a supplied transformer: a 24 VAC, Class 2 power source a VAC outlet ZFR1821 and ZFR1822 Pro Routers A ZFR1821 or ZFR1822 Pro Router is used with any WEFC to provide a wireless interface between a field controller and: the NAE supervisory controller (by means of a WNC Gateway) its associated WRZ Series Sensors The ZFR1821 or ZFR1822 Pro Router can also be used as a repeater to extend the range of the data communications within the wireless mesh network, or to fill any gaps within the mesh network, based on the physical layout of the wireless devices, obstacles, and other characteristics of the installation site. A ZFR1821 or ZFR1822 Pro Router is powered directly from the connected field controller s 15 VDC output. When ordered as a repeater, a 24 VAC-15 VDC power supply is included as a repeater accessory to allow use as a stand-alone repeater. The ZFR1822 Pro Router is an alternate packaging design to the ZFR1821 Pro Router and is intended for flush wall-mount or ceiling-mount applications. The ZFR1822 Pro Router can be mounted in open areas of a building, which can improve communication distances between wireless devices. The ZFR1822 Pro Router includes mounting hardware and a 10-foot RJ- 12 cable for interfacing to wirelessly enabled field controllers. Repeater kits are used to extend wireless transmission distances or fill in gaps in a wireless mesh to increase wireless reliability. Each repeater kit includes everything you need to install one ZFR1821 or ZFR1822 Pro Router as a repeater in a ZFR Pro Wireless Field Bus System: ZFR1821 or ZFR1822 Pro Router 24 VAC to 15 VDC power supply for the ZFR1822 Pro Router RJ-12 cable for power extension Mounting hardware Notes: Use the ZFR1821 Pro Router for above ceiling mounting Use the ZFR1822 Pro Router for flush wallmount and below ceiling-mount applications Supported Field Controllers The ZFR Pro Wireless Field Bus System enables wireless BACnet connectivity between WEFCs, such as wireless TEC3000s, FACs, FECs, IOMs, or VMA16 controllers and Network Automation Engines, including NAE/35/45/55s. In addition, the wireless field bus system provides wireless communication between FEC/VMA16 controllers and WRZ Series wireless sensors. Notes: The ZFR1821 or ZFR1822 Pro Router is automatically updated during the main code download to the field controller. For information on uploading or downloading the devices to match, refer to the Loading Devices chapter of the CCT Help (LIT ). WEFCs can also use hard-wired NS Series network sensors. TEC3000 Series Wireless Thermostat Controllers The TEC3000 Series Thermostat Controllers are wireless, stand-alone devices that provide on/off, floating, and proportional control of the following: local hydronic reheat valves pressure-dependent VAV equipment with or without local reheat two- or four-pipe fan coils cabinet unit heaters other zoning equipment using an on/off, floating, or 0 to 10 VDC proportional control input The wireless TEC3000 models have an embedded ZFR radio that is updated during a firmware update. Models also provide single- or two-stage control of unitary rooftop units (RTUs) with or without economizers and heat pumps. 4

5 WRZ Series Sensors Depending on the sensor model, the WRZ Series Sensors transmit temperature, setpoint, humidity, occupancy status, and low battery conditions to an associated field controller by means of a ZFR1821 or ZFR1822 Pro Router. If the field controller is mapped to the engine, the data sent by the wireless sensor can be displayed. Some applications that support the temperature or humidity control functions do not support the occupancy/temperature setback function. Refer to a field controller s commissioning and operation literature to determine if the application supports occupancy or temperature setback functions. Notes: Configure the Analog Inputs (AIs) on all WRZ Sensors as SA Bus devices (the same as with hard-wired NS Series Sensors). The WRZ Series Sensors are designed for indoor, intra-building applications only. The WRZ Series Sensors require two 1.5 VDC AA alkaline batteries. The WRZ sensors minimize power consumption by transmitting data only once per minute, which yields an expected battery life of up to 5 years. ZFR Checkout Tool (ZCT) The ZFR Checkout Tool at version 6.3 or later, is an optional tool, included with the installation of the Controller Configuration Tool (CCT), or it can be downloaded as a stand-alone application. ZCT allows you to validate the wireless connectivity and health of wireless devices within a ZFR Pro Wireless Field Bus System, helping ensure a reliable mesh network is in place. You can use the information provided by the ZCT to analyze and troubleshoot the wireless mesh network created by a ZFR Pro Wireless Field Bus System. The ZCT gathers information by discovering the wireless field controllers and wireless sensors on your network and analyzing their status and wireless communication paths. The ZCT provides a simple report of wireless network performance, including online status verification and wireless signal strength information. The ZCT also provides wireless device lists, signal strength information, and diagnostic measurements of the wireless mesh network. Refer to the ZCT Help (LIT ) for more information on the ZCT. The ZCT requires a ZFR Wireless Universal Serial Bus (USB) Dongle adapter with ZFR driver as described below. Note: You must connect the adapter to the computer running CCT/ZCT before attempting to scan the network. ZFR Wireless USB Dongle The ZFR connection type within CCT requires the USB adapter with ZFR driver for your laptop computer. The ZFR Wireless USB Dongle allows a laptop computer to connect to a ZFR wireless field bus for the purpose of commissioning and downloading applications to wirelessly enabled field controllers using the CCT. It is also used for analyzing a ZFR wireless mesh using the ZCT. The ZFR Wireless USB Dongle requires a USB software driver that is installed automatically with CCT Version 5.3 or later. No user configuration is required. See Table 7 to order the ZFR USB adapter (product code ZFR-USBHA-0). This device is an IEEE ZFR to USB Adapter for the 2.4 GHz ISM Band. For more information, refer to the WNC1800/ZFR182x Pro Series Wireless Remote Field Bus System Technical Bulletin (LIT ). WRZ-SST-120 Wireless Sensing System Tool Use the optional, battery-operated WRZ-SST-120 Wireless Sensing System Tool with any model WRZ Series Sensor as a site survey tool to determine the wireless signal strength between potential locations of ZFR1800 system devices to survey your application and adjust ZFR1800 device locations before installing the devices. Refer to the WRZ-SST-120 Wireless Sensing System Tool Installation Instructions (Part No ) for more information on the tool. 5

6 Figure 2: ZFR Pro Wireless Field Bus System as Part of a Metasys Network WNC1800/ZFR182x Pro Series Wireless Field Bus System Wireless Communication The ZFR Pro Series System devices create a wireless mesh network using the ZigBee enhancement to the IEEE standard. The mesh network provides redundant wireless paths, enabling the BACnet data to traverse the network through alternate, automatically forming paths and arrive at the target destination device even if a ZFR1821 or ZFR1822 Pro Router or Repeater within the wireless mesh network experiences interference or drops out of the network. The ZFR Pro System radios use Direct Sequence Spread Spectrum (DSSS) Radio Frequency (RF) technology and operates on the globally accepted 2.4 GHz Industrial, Scientific, and Medical (ISM) band. All ZFR Pro System radios use a transmission power of 10 mw and meet the Institute of Electrical and Electronics Engineers, Inc. (IEEE) standard for low power, low duty-cycle wireless transmitting systems. For more information on wireless transmissions, signal strength, and locating devices for optimum signal strength, refer to the WNC1800/ZFR182x Pro Series Wireless Remote Field Bus System Technical Bulletin (LIT ). Wireless Signal Transmission Range The effective transmission range/distance for indoor applications varies because of wireless signal absorption and reflection due to metal obstructions, walls (or floors), and furniture found in typical building interiors. Transmission ranges between ZFR182x Pro Series products can be less than the maximum distances shown in Table 4. Table 4: Indoor Line-of-Sight Transmission Ranges Range Type Transmission Distance ZFR1820 or ZFR1823 Pro Coordinator Radio, ZFR1821 or ZFR1822 Pro Router WRZ Series Sensor Recommended 15.2 m (50 ft) 15.2 m (50 ft) Maximum 76.2 m (250 ft) 30 m (100 ft) Wireless Interference and Security The ZFR Pro Wireless Field Bus System is designed to minimize the potential for wireless interference with other wireless applications. In most commercial environments, the ZFR182x Series System does not encounter or generate wireless interference, even in environments with cell phones and competing Wi-Fi applications. 6

7 ZFR182x Series Wireless transmissions use different modulation schemes than Wi-Fi applications and use frequencies between popular Wi-Fi bands, enabling Wi-Fi and ZFR1800 Series Wireless networks to coexist in the same areas. For more information on wireless interference and security, refer to the WNC1800/ZFR182x Pro Series Wireless Remote Field Bus System Technical Bulletin (LIT ). Physical Features and Dimensions Figure 3 shows the WNC Gateway. Note that the overall dimensions depend on the mounting options used. The dimensions of the unit itself are: 120 x 70 x 24.5 mm (4-23/32 x 2-3/4 x 31/32 in. when used vertically). Refer to the WNC1800 Wireless Network Coordinator Gateway Installation Instructions (Part No ) for mounting dimensions. Figure 3: WNC Gateway Figure 4 shows the dimensions of the ZFR1820 Pro Coordinator radio and the ZFR1821 Pro Router. These two devices have the same form factor. Figure 4: ZFR1820 Pro Coordinator Radio and ZFR1821 Pro Router, Physical Features and Dimensions, mm (in.) 7

8 Figure 5 shows the dimensions of the ZFR1822 Pro Router and the ZFR1823 Pro Coordinator Radio. These models are intended for wall- or ceiling-mount applications. Figure 7 shows the WRZ Series Sensor. Figure 7: WRZ Series Sensor, Physical Features and Dimensions, mm (in.) Figure 5: ZFR1822 Pro Router and ZFR1823 Pro Coordinator Radio, Physical Features and Dimensions, mm (in.) Figure 6 illustrates features and dimensions of wireless TEC 3000 Thermostat Controllers. Figure 6: Wireless TEC3000 Thermostat Controller Ordering Information For WNC1800/ZFR182x Pro Series System product ordering information, see Table 5. For WNC1800/ ZFR182x Pro Series System accessories product ordering information, see Table 7. For supported models of the Metasys BACnet field controllers, refer to the Metasys System Field Equipment Controllers and Related Products Product Bulletin (LIT ). For wireless TEC3000 model information, refer to the TEC3000 Series Wireless, Stand-Alone, and Field-Selectable BACnet MS/TP or N2 Networked Thermostat Controllers Product Bulletin (LIT ). Contact the nearest Johnson Controls representative to order the products ZFR Pro products. Specify the desired product code number from the ordering tables in this document and in related literature. Refer to the Network Automation Engine (NAE) Product Bulletin (LIT ) and the Metasys System Field Equipment Controllers and Related Products Product Bulletin (LIT ) for additional information on related products. 8

9 Repair Information If a ZFR Pro Wireless Field Bus System component fails to operate within its specifications, replace the unit. For a replacement ZFR Pro Series System component, contact the nearest Johnson Controls representative. Table 5: ZFR Pro Wireless Field Bus System Components (Part 1 of 2) Product Code Product Description Number MS-WNC1820-0A MS-WNC1823-0A MS-ZFR1821-0B MS-ZFR1822-0B MS-ZFR MS-ZFR The MS-WNC1820-OA kit is comprised of the following components: WNC Gateway and mounting base with 110/220 VAC Power Supply. The ZFR1820 Pro Coordinator Radio with 3-Foot RJ-12 connecting cable Box mount for ZFR1820 Pro Coordinator Radio The MS-WNC1823-OA kit is comprised of the following components: WNC Gateway and mounting base with 110/220 VAC Power Supply. The ZFR1823 Pro Coordinator Radio with 10-Foot RJ-12 connecting cable. Mounting screws for ZFR1823 Pro Coordinator Radio Note: A field-provided ceiling clip is required to mount the ZFR1823 Pro Coordinator Radio below grid ceilings The MS-ZFR1821-0B kit is comprised of the following components: ZFR1821 Pro Router, EMT mount, with 3-Foot RJ-12 connecting cable. 24 VAC to 15 VDC power supply for the router. Box mount for ZFR1821 Pro Router Note: Use the ZFR1821 EMT mount repeater for above the ceiling mounting. Use the alternative ZFR1822 Pro Router for flush wall-mount or below the ceiling-mount applications. A field-provided ceiling clip is required to mount the ZFR1822 Pro Router below grid ceilings. The MS-ZFR1822-0B kit is comprised of the following components: ZFR1822 Pro Router, wall-mount, with 10-Foot RJ-12 connecting cable. 24 VAC to 15 VDC power supply for the router. Drywall-mounting hardware (ceiling clips not provided due to variety of ceiling types) Note: Use the ZFR1822 Pro Router for flush wall-mount or below the ceiling-mount applications. A field-provided ceiling clip is required to mount the ZFR1822 Pro Router below grid ceilings. Use the alternative ZFR1821 EMT mount repeater for above the ceiling mounting. The MS-ZFR kit is comprised of the following components: ZFR1821 Pro Router, EMT mount, functions with Metasys BACnet WEFCs and WRZ Series Sensors Box mount for ZFR1821 Note: Use the ZFR1821 EMT mount repeater for above the ceiling mounting. Use the alternative ZFR1822 Pro Router for flush wall-mount or below the ceiling-mount applications. A field-provided ceiling clip is required to mount the ZFR1822 Pro Router below grid ceilings. The MS-ZFR kit is comprised of the following components: ZFR1822 Pro Router, wall-mount; functions with Metasys BACnet WEFCs and WRZ Series Sensors Drywall-mounting hardware (ceiling clips not provided due to variety of ceiling types) Notes: Use the ZFR1822 Pro Router for flush wall-mount or below the ceiling-mount applications. A field-provided ceiling clip is required to mount the ZFR1822 Pro Router below grid ceilings. Use the alternative ZFR1821 EMT mount repeater for above the ceiling mounting. 9

10 Table 5: ZFR Pro Wireless Field Bus System Components (Part 2 of 2) MS-WNC1820-0B MS-WNC1823-0B The MS-WNC1820-OB kit is comprised of the following components: WNC Gateway and mounting base with 24 VAC Power Supply and WNC power adapter cable ZFR1820 Pro Coordinator Radio with 3-Foot RJ-12 connecting cable Box mount for ZFR1820 Pro Coordinator Radio The MS-WNC1823-OB kit is comprised of the following components: WNC Gateway and mounting base with 24 VAC Power Supply and WNC power adapter cable. ZFR1823 Pro Coordinator Radio with 10-Foot RJ-12 connecting cable. Mounting screws for ZFR1823 Pro Coordinator Radio Note: A field-provided ceiling clip is required to mount the ZFR1823 Pro Coordinator Radio below grid ceilings Table 6: Related Field Controllers and Sensors Product Code Product Description Number TEC30xx-0x-000 MS-FACxxxx, MS- FECxxxx, MS- IOMxxxx, MS- VMAxxxx WRZ-xxxx For information on Wireless TEC3000 Models, refer to the TEC3000 Series Wireless, Stand-Alone, and Field-Selectable BACnet MS/TP or N2 Networked Thermostat Controllers Product Bulletin (LIT ) for ordering information. This document describes the different models and links to further information such as installation instructions. For information on Wireless Enabled Field Controllers, refer to the Metasys System Field Equipment Controllers and Related Products Product Bulletin (LIT ). This document describes the different models and links to further information such as installation instructions. For information on WRZ Series Room sensors, refer to the WRZ Series Wireless Room Sensors Product Bulletin (LIT ). This document describes the different models and links to further information such as installation instructions. Table 7: Accessories Product Code Product Description Number MS-ZFRCBL-0 ZFR-USBHA-0 ZFR-WallCover WRZ-SST VDC, AA Alkaline Battery Wire Harness with Connectors for use with MS-ZFR182x-x Router for Wireless Field Bus. Allows ZFR1821 or ZFR1822 Pro Router to function with FEC1620 controller; and with FEC1610, VMA1610, or VMA1620 controllers in conjunction with NS Series Sensors, MS-BTCVT-1 Wireless Commissioning Converter, or DIS1710 Local Controller Display. Universal Serial Bus (USB) Dongle with ZFR Driver provides a wireless connection through the CCT to allow wireless commissioning of the wirelessly enabled FEC, IOM, and VMA16 Series Field Controllers. Also used for the ZFR Checkout Tool (ZCT) in CCT. The ZFR-Wall Cover is an optional accessory of the ZFR Pro Series Wireless Field Bus System and is meant to enable mounting of the ZFR1822 Pro Router or ZFR1823 Pro Coordinator Radio, to be wallmounted to an existing double-gang electrical box. Optional Wireless Sensing System Tool to be used with a WRZ Series Sensor to indicate wireless signal strength between potential locations of ZFR1800 System devices. Replacement Battery for WRZ Series Sensors (Purchase Locally) 10

11 Technical Specifications WNC Gateway (Part 1 of 2) Product Code Number Power Consumption Ambient Temperature Conditions Ambient Humidity Conditions Transmission Power (Wi-Fi) (Typical) WLAN Receiver Sensitivity (Typical) Transmission Speeds Wi-Fi Transmission Range (Typical) ZFR Pro Transmission Range Wi-Fi Wireless Security Network and Serial Interfaces Dimensions (H x W x D) Housing Weight MS-WNC1800-0S: WNC Gateway and mounting base IMPORTANT: Follow local ordinances for the installation of Class 2 power supplies. Note: Used in the following kits, see Table 5. MS-WNC1820-0A MS-WNC1823-0A MS-WNC1820-0B MS-WNC1820-0B From SA/FC bus: 15 VDC at 2.7 VA maximum Operating: 0 to 50 C (32 to 122 F) Operating Survival: -30 to 60 C (-22 to 140 F) Non-Operating: -40 to 70 C (-40 to 158 F) Storage: -40 to 70 C (-40 to 158 F); 5 to 95% RH 30 C (86 F) maximum dew point conditions Operating: 0 to 50 C (32 to 122 F); 5 to 95% RH, 30 C (86 F) maximum dew point conditions Wireless Local Area Network (WLAN) Transmission Power: dbm, 54 Mbps dbm, 65 Mbps -76 dbm, 10% packet error rate (PER ), 54 Mbps -73 dbm, 10% PER, 65 Mbps Wireless Communication: 2.4 GHz ISM bands, b/g/n, 11/22/54 Mbps Serial Communication (SA/FC Bus): 9600, 19.2k, 38.4k, or 115.2k bps Ethernet Communication: 10, 100 Mbps Wi-Fi Wireless Communication: 30 m (100 ft) line-of-sight indoors, however a typical indoor range in an area with obstacles is 15 m (50 ft). WLAN Range Performance: 0 15 m (0 50 ft) = Excellent m ( ft) = Good m ( ft) = Weakest, approaching out of range ZFR Pro Communications ( ): 76 m (250 ft) Maximum Indoor Line-of-Sight 15 m (50 ft) Recommended Indoor WPA2-PSK TKIP (Wi-Fi Protected Access Pre-Shared Key Mode Temporal Key Integrity Protocol) WPA2-EAP-PEAP WPA2-EAP-TLS One SA/FC port (6-pin port; connects with ZFR1820 or ZFR1823 Pro Coordinator Radio. Can be extended to 30 m (100 ft), if necessary) One USB port (Micro-B port; 2.0; supports Open Host Controller Interface [Open HCI] specification) Unit alone: 120 x 70 x 24.5 mm (4-23/32 x 2-3/4 x 31/32 in. when used vertically) Unit in shell: 128 x 75 x 29.5 mm (5-1/32 x 2-61/64 x 1-5/32 in. when used vertically) White Acrylonitrile butadiene styrene (ABS) bracket, plenum-rated WNC Gateway alone: 0.10 kg (0.22 lb) Note: Weights do not include any peripheral components such as cables, lanyard, or an external power supply. 11

12 WNC Gateway (Part 2 of 2) Web Browser Requirements for Computers and Handheld Devices Compliance Computer: Windows Internet Explorer 10 and Windows Internet Explorer 11, Apple Safari 6.1 and later, and Google Chrome Handheld Device: The handheld device must be running either Internet Explorer Mobile for Windows Mobile version 5 or version 6 operating system (OS); Apple iphone and ipod touch ios version 7.0 or greater; Android 4.0.3, 4.0.4, and 4.1+, or Google Chrome. Other web browsers may display the UI, but the functionality is not guaranteed. United States UL Listed File E365459, ANSI/UL , Information Technology Equipment; UL 2043 (Stationary version only), Suitable for Use in Other Environmental Air Space in Accordance with Section , (C) of the National Electric Code. Transmission Complies with FCC Part Regulations for Low Power Unlicensed Transmitters Transmitter FCC Identification: OEJ-MAPWIFI FCC Compliant to CFR 47, Part 15, Subpart B, Class A Canada: Industry Canada IC: 279A-MAPWIFI IC: RSS-210 ULC Listed File E365459, CAN/CSA-C22.2 No , Safety of Information Technology Equipment Australia and New Zealand: RCM Mark, Australia/NZ Emissions Compliant. Europe: CE Mark Johnson Controls declares that this product is in compliance with the essential requirements and other relevant provisions of the RED Directive and the EMC Directive. CE Emission: EN : 2007; Generic standards for residential, commercial, and light-industrial environments. ETSI EN : , ETSI EN : (Class 2), IEC / EN ZFR1820/ZFR1823 Pro Coordinator Radio (Part 1 of 2) Product Code Number MS-ZFR1820-x: ZFR1820 Pro Conduit-Mount Coordinator Radio MS-ZFR1823-x: ZFR1823 Pro Wall-Mount Coordinator Radio Power Supply Input 15 VDC Nominal. Provided through the RJ-12 cable connected to the WNC Gateway. Addressing DIP Switches, Field Adjustable Wireless Band Direct-Sequence Spread-Spectrum, 2.4 GHz ISM Bands Transmission Power 10 mw Maximum Transmission Range 76.2 m (250 ft) Maximum Line-of-Sight 15 m (50 ft) Recommended Ambient Conditions Operating: 0 to 50 C (32 to 122 F), 5 to 95% RH, Noncondensing Storage: -20 to 70 C (-4 to 158 F), 5 to 90% RH, Noncondensing Materials ZFR1820: White Plastic Housing with Plenum rating per UL1995 UL94-5VB Flammability Rating ZFR1823: White PC/ABS Cycoloy Terminations RJ-12 plug for connection to WNC1800 Gateway Dimensions ZFR1820: 136 x 100 x 18 mm (5-3/8 x 3-15/16 x 3/4 in.) ZFR1823: 63.5 x 100 x 20.3 mm (2-1/2 x 3-15/16 x 4/5 in.) Mounting Hardware ZFR1820: 1/2 in. trade size Electrical Mechanical Tubing (EMT) connector ZFR1823: Screw mounted Shipping Weights ZFR1820: kg (0.21 lb) ZFR1823: kg (.25 lb) 12

13 ZFR1820/ZFR1823 Pro Coordinator Radio (Part 2 of 2) Compliance United States: UL 916 Energy Management Plenum rated per UL1995 UL94-5VB Flammability Rating FCC Compliant to CFR47, Part 15, Subpart B, Class A Transmission Complies with FCC Part Regulations for Low Power Unlicensed Transmitters Transmitter Identification ZFR1820/ZFR1823: FCC: OEJ-WRZRADIO Canada:CAN/CSA C22.2 No. 205, Signal Equipment Industry Canada (IC) Compliant to Canadian ICES-003, Class B Limits Industry Canada (IC) RSS-210 Transmitter Identification ZFR1820/ZFR1823: 279A-WRZRADIO Australia and New Zealand: RCM Mark, Australia/NZ Emissions Compliant Europe: CE Mark Johnson Controls declares that this product is in compliance with the essential requirements and other relevant provisions of the EMC Directive. ZFR1821/ZFR1822 Pro Routers (Part 1 of 2) Product Code Number MS-ZFR1821-0: ZFR1821 Pro Router, Conduit-Mount, for Field Controller Router Applications MS-ZFR1822-0: ZFR1822 Pro Router, Wall-Mount, for Field Controller Router Applications MS-ZFR1821-0B: ZFR1821 Pro Router, Conduit-Mount, with 24 VAC Power Supply for Field Controller Router Applications MS-ZFR1822-0B: ZFR1822 Pro Router, Wall-Mount, with 24 VAC Power Supply for Field Controller Router Applications Power Supply Input 15 VDC Nominal. Provided through the RJ-12 cable connected from a field controller or repeater power supply. Addressing DIP Switches, Field Adjustable Wireless Band Direct-Sequence Spread-Spectrum, 2.4 GHz ISM Bands Transmission Power 10 mw Maximum Transmission Range 76.2 m (250 ft) Maximum Line-of-Sight 15 m (50 ft) Recommended Ambient Conditions Operating: 0 to 50 C (32 to 122 F), 5 to 95% RH, Noncondensing Storage: -20 to 70 C (-4 to 158 F), 5 to 90% RH, Noncondensing Materials ZFR1821: White Plastic Housing with Plenum rating per UL1995 UL94-5VB Flammability Rating ZFR1822: White PC/ABS Cycoloy Terminations RJ-12 plug for connection to field controllers or Repeater Kit power supply Dimensions ZFR1821: 136 x 100 x 18 mm (5-3/8 x 3-15/16 x 3/4 in.) ZFR1822: 61 x 100 x 20.5 mm (5-3/8 x 3-15/16 x 3/4 in.) Mounting Hardware ZFR1821: 1/2 in. trade size Electrical Mechanical Tubing (EMT) connector ZFR1822: Screw mounted Shipping Weights ZFR1821: kg (0.21 lb) ZFR1822: kg (.25 lb) Repeater Power Supply: 227 kg (.50 lb) 13

14 ZFR1821/ZFR1822 Pro Routers (Part 2 of 2) Compliance United States: UL 916 Energy Management Plenum-rated per UL1995 UL94-5VB Flammability Rating FCC Compliant to CFR47, Part 15, Subpart B, Class A Transmission Complies with FCC Part Regulations for Low Power Unlicensed Transmitters Transmitter Identification ZFR1821/ZFR1822: FCC: OEJ-WRZRADIO Canada: CAN/CSA C22.2 No. 205, Signal Equipment Industry Canada (IC) Compliant to Canadian ICES-003, Class B Limits Industry Canada (IC) RSS-210 Transmitter Identification ZFR1821/ZFR1822: 279A-WRZRADIO Australia and New Zealand: RCM Mark, Australia/NZ Emissions Compliant Europe: CE Mark Johnson Controls declares that this product is in compliance with the essential requirements and other relevant provisions of the EMC Directive. European Single Point of Contact: NA/SA Single Point of Contact: APAC Single Point of Contact: JOHNSON CONTROLS WESTENDHOF ESSEN GERMANY JOHNSON CONTROLS 507 E MICHIGAN ST MILWAUKEE WI USA JOHNSON CONTROLS C/O CONTROLS PRODUCT MANAGEMENT NO. 22 BLOCK D NEW DISTRICT WUXI JIANGSU PROVINCE CHINA Building Technology & Solutions 507 E. Michigan Street, Milwaukee, WI Metasys and Johnson Controls are registered trademarks of Johnson Controls All other marks herein are the marks of their respective owners Johnson Controls 14 Published in U.S.A.