SGE-3G/GPRS INSTRUCTION MANUAL (M179B A)

Size: px

Start display at page:

Download "SGE-3G/GPRS INSTRUCTION MANUAL (M179B A)"

Francine Hawkins
5 years ago
Views:

1 Modem/Router INSTRUCTION MANUAL (M179B A)

2 2

SAFETY PRECAUTIONS Follow the warnings described in this manual with the symbols shown below. DANGER Warns of a risk, which could result in personal injury or material damage.

3 SAFETY PRECAUTIONS Follow the warnings described in this manual with the symbols shown below. DANGER Warns of a risk, which could result in personal injury or material damage. ATTENTION Indicates that special attention should be paid to a specifi c point. If you must handle the unit for its installation, start-up or maintenance, the following should be taken into consideration: Incorrect handling or installation of the unit may result in injury to personnel as well as damage to the unit. In particular, handling with voltages applied may result in electric shock, which may cause death or serious injury to personnel. Defective installation or maintenance may also lead to the risk of fi re. Read the manual carefully prior to connecting the unit. Follow all installation and maintenance instructions throughout the unit s working life. Pay special attention to the installation standards of the National Electrical Code. Refer to the instruction manual before using the unit In this manual, if the instructions marked with this symbol are not respected or carried out correctly, it can result in injury or damage to the unit and /or installations. CIRCUTOR, SA reserves the right to modify features or the product manual without prior notifi cation. DISCLAIMER CIRCUTOR, SA reserves the right to make modifi cations to the device or the unit specifi cations set out in this instruction manual without prior notice. CIRCUTOR, SA on its web site, supplies its customers with the latest versions of the device specifi cations and the most updated manuals. 3

4 CONTENTS SAFETY PRECAUTIONS...3 DISCLAIMER...3 CONTENTS...4 REVISION LOG...5 SYMBOLS VERIFICATIONS UPON RECEPTION DESCRIPTION OF THE PRODUCT INSTALLING THE DEVICE PRELIMINARY RECOMMENDATIONS INSTALLATION INSTALLATION ON DIN RAIL PANEL-MOUNTED INSTALLATION TERMINALS OF THE DEVICE START-UP OPERATION INDICATOR LEDs COMMUNICATIONS PORTS CONFIGURATION MODEM DynDNS TIME: NTP SERVER ETHERNET PORT PORT FORWARDING RS RS DELIVERY OF SMS MESSAGES SECURITY SAVING THE CONFIGURATION TECHNICAL FEATURES TECHNICAL SERVICE WARRANTY CE CERTIFICATE

REVISION LOG Table 1: Revision log. Date Revision Description 06/17 M179B01-03-17A Initial Version SYMBOLS Symbol Table 2: Symbols. Description In compliance with the corresponding European directive.

5 REVISION LOG Table 1: Revision log. Date Revision Description 06/17 M179B A Initial Version SYMBOLS Symbol Table 2: Symbols. Description In compliance with the corresponding European directive. The unit complies with the 2002/96/EC European directive. Do not dispose of the unit in a household waste container at the end of its useful life. Observe the local electronic unit recycling regulations. Direct current. ~ Alternating current. Note: The images of the devices are for illustrative purposes only and might differ from the original device. 5

1.- VERIFICATIONS UPON RECEPTION The following must be checked upon reception of the device: a) The device has been supplied according to the specifications in your order.

6 1.- VERIFICATIONS UPON RECEPTION The following must be checked upon reception of the device: a) The device has been supplied according to the specifications in your order. b) The device has not been damaged during transport. c) Perform an external visual inspection of the device before connecting it. d) Check that it has been supplied with the following: - An installation guide. Immediately contact the carrier and/or CIRCUTOR's after-sales service if you detect any problem in the device upon reception. 2.- DESCRIPTION OF THE PRODUCT The can connect an application to the Internet via IP connections locally or through networks. The can be connected to UMTS networks (Universal Mobile Telecommunication System) where this technology is installed. Otherwise, it will connect via GPRS networks (General Packet Radio Service). The SIM card installed must have the necessary services, which must have been activated by its service provider. In the case of facilities with no fixed IP, the is compatible with the DYNDNS service. The device features: - 3 communications ports: Ethernet, RS-232 and RS Indicator LEDs. 6

7 3.- INSTALLING THE DEVICE PRELIMINARY RECOMMENDATIONS The people using and handling the device must follow the safety measures established in the country where the device will be used to guarantee its safe operation, using personal protective equipment if needed. The device must be installed by authorised and qualified staff. Disconnect the device from the mains and disconnect the measuring devices before handling, changing the connections of or replacing the device. Handling the device while it is connected is hazardous to the people near it. The cables must be in perfect working order to prevent accidents or injuries to people and/or damage to the facilities/installations. Limit the operation of the device to measuring the specified current or voltage values. The manufacturer of the device shall not be held responsible for any damage resulting from the user or installation company failing to observe the warnings and/or recommendations indicated in this manual nor for the damage derived from the use of non-original products or accessories or those from other brands. Inspect the device before using it. Make sure that there are no cracks and that the housing is intact. Do not use the device to take measurements if you detect an anomaly or malfunction. Check the environment in which the device is installed before taking a measurement. Do not use the device to take measurements in dangerous, explosive, wet or damp environments. Disconnect the device from the mains and from the power supply (both the device and its measuring system) before performing any maintenance operations, repairs or handling any of the connections of the device. Contact the after-sales service if you detect that the device is not working properly. 7

8 3.2.- INSTALLATION While the device is connected, the terminals, opening the cover or removing elements can expose parts that are hazardous to the touch. The device must not be used until the installation process is complete. The device must be connected to a power circuit that is protected with GL (IEC 269) or M-type fuses, rated 0.5 to 2A. It must feature a thermal-magnetic circuit breaker or equivalent device to disconnect the device from the mains. The power circuit of the device will be connected with a cable with a minimum cross-section of 1.5 mm². The device can be connected to other CIRCUTOR modules. To do so, insert the plastic clips, as shown in Figure 1, to guarantee that the modules are firmly connected. Figure 1: Inserting the clips. The device can be installed on a DIN Rail or mounted on a panel INSTALLATION ON DIN RAIL Figure 2 shows how the DIN Rail fastening elements must be attached to the rear of the device. Figure 2:Fitting the DIN Rail fixing elements. 8

9 Lift the guides after fitting the guides and mounting the on a DIN rail, to ensure they are firmly secured PANEL-MOUNTED INSTALLATION Figure 3 and Figure 4 show different options that can be used to fit the panel mounting guides. The modules are somewhat symmetrical, so they can be attached to the panel in different ways. Figure 3: Option 1: Fitting the panel fixing elements. Figure 4: Option 2: Fitting the panel fixing elements. Figure 5 shows how to insert the screws to secure the panel fixing elements. 9

10 Figure 5:How to insert the screws into the panel fixing elements TERMINALS OF THE DEVICE Table 3:List of terminals of the. Terminals of the 1: Ethernet Communications 5: A, RS-485 Communications 2: RS-232 Communications 6: N, Auxiliary power supply 3: B, RS-485 Communications 7: L, Auxiliary power supply 4: S, RS-485 Communications Figure 6: Terminals. 10

4.- START-UP The following conditions must be met to guarantee the proper operation of the : The antenna must meet the GMS frequency range requirements established in each country.

11 4.- START-UP The following conditions must be met to guarantee the proper operation of the : The antenna must meet the GMS frequency range requirements established in each country. The SIM card must be supplied by the mobile phone operator and have the data transmission function active to guarantee its correct operation. The PIN code must be deactivated before the SIM card is inserted. The Modem/Router must be configured on its web site, so no additional software is required to start-up the device. A computer with an Ethernet port and an Ethernet crossover cable are required to configure the device. The default IP address of the device is: IP: Netmask: A secure web protocol (HTTPS) is required to access the through the web site. The device will be accessed from the following address: The SIM card is inserted through the rear of the. Press the button on the slot to extract the card holder. Figure 7: Slot used to insert the SIM card. 11

12 5.- OPERATION INDICATOR LEDs The device features 11 Indicator LEDs, Figure 10 and Table 4. H M L 3G Stat PMon Tx Rx Tx Rx ON Figure 8: Indicator LEDs. LED H M L 3G Stat PMon Tx Rx ON Table 4: Description of the LEDs Description Very good coverage Good coverage Poor coverage Steady: Device connected to a 3G network Flashing: Device connected to a GPRS network Modem active Concentrator power supply Delivery of data via RS-232 or RS-485 Reception of data via RS-232 or RS-485 The device is working correctly 12

5.2.- COMMUNICATIONS PORTS The features three communications ports: Ethernet (terminal in Table 3) allows the device to communicate with a PC or any device with a communication port.

The port must be configured from the web site of the. Table 5: RS-232 Connector.

13 5.2.- COMMUNICATIONS PORTS The features three communications ports: Ethernet (terminal in Table 3) allows the device to communicate with a PC or any device with a communication port. This is the port through which the device is configured, see 6.- CONFIGURATION. RS-232 (terminal 2 in Table 3) allows the device to communicate with any device using this protocol. The port must be configured from the web site of the. Table 5: RS-232 Connector. RS-232 Connector PIN Description 1 GND 2 RX 3 TX 4 CTS 5 RTS 6 GND If the RS-232 port has been deactivated, bridge pins 4 and 5 for at least 3 seconds to send SMS messages to the telephone number configured in the web site of the SGE-3G/ GPRS. RS-485 (terminals 3, 4 and 5 in Table 3) allows the device to communicate with any other device using this protocol. The port must be configured from the web site of the. 13

6.- CONFIGURATION After connecting to the Local Area Network (LAN) and configuring the IP address or DHCP name, the device features an internal web site where the network protocol and serial port

14 6.- CONFIGURATION After connecting to the Local Area Network (LAN) and configuring the IP address or DHCP name, the device features an internal web site where the network protocol and serial port configuration parameters can be configured. To access this web site, simply use a conventional browser and enter the default IP address in the : This is a secure web site; select the Continue to this website (not recommended) option. Press the "Setup" button to access the setup screen of the. Figure 9 shows the home configuration screen. Figure 9: Home configuration screen. It shows: Connection: Type of connection established and power of the signal. IP address: IP address Hostname: Name of the DynDNS (only active if the DynDNS has been programmed) Time: Time of the. Press the Setup button to access the setup screen of the. 14

6.1.- MODEM The can be connected to 3G or GPRS networks. The parameters provided by the operator of the SIM card must be configured to access some of these networks. Figure 10: Setup screen: Modem. 6.

15 6.1.- MODEM The can be connected to 3G or GPRS networks. The parameters provided by the operator of the SIM card must be configured to access some of these networks. Figure 10: Setup screen: Modem DynDNS The DynDNS service (Dynamic Domain Server) allows the real-time update of information about domain names in a name server. The most common use is the assignment of an Internet domain name to a computer with a variable IP address (in our case, with a dynamic IP address). This allows the establishment of a connection with the device without the need for an Internet connection with identification via a fixed IP address. Servers DYNDNS Sending the IP (publishes) + Hostname DYNDNS DYNDNS hostname IP request Facilitates IP Computer to which the wants to connect DYNDNS connection Ethernet connection Private IP Figure 11: Operation of the DynDNS service. Users that wish to use the DynDNS service must be registered in the service. To do so, open the following web site: Figure 12: Setup screen: DynDNS. 15

16 Setup parameters: Hostname: hostname of the DynDNS service that the user must have created previously. User: Name of the user of the DynDNS account to access the service. Password: Password of the user of the DynDNS account to access the service TIME: NTP SERVER The can be synchronised with the NTP (Network Time Protocol) time and date server in a UTC time system. The default device shows no values, indicating that the system is synchronised with DHCP, provided that the network server allows this. 2 NTP servers can be configured, in case one stops operating. Figure 13: Setup screen: Time, NTP server. The device time can be updated with 2 methods: 1.- Press the Sync to PC Time button to synchronise the time of the with that of the PC. 2.- Using an NTP time server, for which the following sections must be configured: Primary NTP server and Secondary NTP server ETHERNET PORT The Ethernet port has the following setup parameters: Hostname: Name of the Ethernet port. Address: IP Address of the Netmask: Netmask of the device DHCP: Activates the DHCP server of the First address: Start IP of the DHCP. Last address: Final IP of the DHCP. Forced DNS server: DNS used to assign the configuration of the DHCP. 16

6.5.- PORT FORWARDING Port Forwarding assigns ports to deliver information through a network of different IP addresses. Figure 14:Port forwarding example.

17 6.5.- PORT FORWARDING Port Forwarding assigns ports to deliver information through a network of different IP addresses. Figure 14:Port forwarding example. Figure 15: Setup screen: Port forwarding. Setup parameters: 3G Port: Input port of the. Forward to Address: Destination IP Address. Port: Port of the destination IP Address. 17

18 6.6.- RS-485 The device features an RS-485 communication bus that is used to communicate with external peripherals, acting as a communications master. Figure 16: Setup screen: RS-485. Setup parameters: Protocol: Communications protocol: TCP or UDP. Port: Destination port of the device with which the system will communicate. Packing timeout: maximum waiting time. Baud rate: Transmission speed: bauds. Data bits: No. of data bits: 7 or 8. Parity: Parity: None, Even or Odd. Stop bits: No. of stop bits: 1 or RS-232 The device features an RS-232 communication bus that is used to communicate with external peripherals, acting as a communications master. Setup parameters: Figure 17: Setup screen: RS-232. Protocol: Communications protocol: TCP or UDP. Port: Destination port of the device with which the system will communicate. Packing timeout: maximum waiting time. Baud rate: Transmission speed: bauds. Data bits: No. of data bits: 7 or 8. Parity: Parity: None, Even or Odd. Stop bits: No. of stop bits: 1 or 2. 18

19 6.8.- DELIVERY OF SMS MESSAGES The device can send SMS messages via port RS-232, see COMMUNICATIONS PORTS. Figure 18: Setup screen: Delivery of SMS messages. Setup parameters: Number : No. of telephones to which the message will be sent. Message text: text of the message that will be sent SECURITY The edit password can be enabled in the, avoiding the modification of the setup parameters. It is not active by default. In case it is activated, the "user" will always be admin, only the password can be modified. Figure 19: Setup screen: Security SAVING THE CONFIGURATION If the information in any of the above sections is modified, it must be saved by pressing the Save Setup button. To return to the default setup, press Load default setup Figure 20: Setup screen: Save the configuration. 19

20 7.- TECHNICAL FEATURES Power supply Rated voltage V ~ Frequency Hz Power VA Installation category CAT III 300V Type Working Life Battery CR2032 SLF (ref: , VARTA) 5 years Type Clock RTC, powered with battery Connection Transmission Antenna: Nominal impedance Antenna: Connector Radio Communications Four-band GSM/GPRS/EDGE: GSM850/900/1800/1900 Double-band HSPA:900/2100 GPRS: D/L up to 85.6Kbps, U/L up to 85.6Kbps EDGE: D/L up to 236.8Kbps, U/L up to 236.8Kbps UMTS: D/L up to 384Kbps, U/L up to 384Kbps HSPA: D/L up to 7.2Mbps, U/L up to 5.76Mbps 50 Ω SMA RS RS-485 Communications Fieldbus RS-485 RS-232 Communications protocol UDP - TCP UDP - TCP Speed bauds bauds Stop bits Parity None - Even - Odd None - Even - Odd Ethernet Communications 10/100 Base-T ; Ethernet IEEE802; 10/100 Mbits/s, self-adapting LED User interface 11 LEDs Environmental features Operating temperature -10ºC ºC Relative humidity (without condensation) % Maximum altitude 2000 m Protection degree IP41 Insulation Class II Mechanical features Dimensions Figure 21 20

21 125 35, Figure 21: Dimensions of the. Standards IEC 60664, VDE 0110, UL 94, EN , EN 55011, EN , EN , EN , EN , EN , EN , EN , EN , EN , EN , EN , EN , EN , EN

8.- TECHNICAL SERVICE In the case of any query in relation to unit operation or malfunction, please contact the CIRCUTOR, SA Technical Support Service.

22 8.- TECHNICAL SERVICE In the case of any query in relation to unit operation or malfunction, please contact the CIRCUTOR, SA Technical Support Service. Technical Assistance Service Vial Sant Jordi, s/n, Viladecavalls (Barcelona) Tel: ( España) / (outside of Spain) sat@circutor.com 9.- WARRANTY CIRCUTOR guarantees its products against any manufacturing defect for two years after the delivery of the units. CIRCUTOR will repair or replace any defective factory product returned during the guarantee period. No returns will be accepted and no unit will be repaired or replaced if it is not accompanied by a report indicating the defect detected or the reason for the return. The guarantee will be void if the units has been improperly used or the storage, installation and maintenance instructions listed in this manual have not been followed. Improper usage is defi ned as any operating or storage condition contrary to the national electrical code or that surpasses the limits indicated in the technical and environmental features of this manual. CIRCUTOR accepts no liability due to the possible damage to the unit or other parts of the installation, nor will it cover any possible sanctions derived from a possible failure, improper installation or improper usage of the unit. Consequently, this guarantee does not apply to failures occurring in the following cases: - Overvoltages and/or electrical disturbances in the supply; - Water, if the product does not have the appropriate IP classifi cation; - Poor ventilation and/or excessive temperatures; - Improper installation and/or lack of maintenance; - Buyer repairs or modifi cations without the manufacturer s authorisation. 22

23 10.- CE CERTIFICATE 23

24 CIRCUTOR, SA Vial Sant Jordi, s/n Viladecavalls (Barcelona) Tel: (+34) Fax: (+34) central@circutor.com

CEM M-RS485 INSTRUCTION MANUAL (M014B A)

Communications interface CEM M-RS485 INSTRUCTION MANUAL (M014B01-03-14A) 2 SAFETY PRECAUTIONS Follow the warnings described in this manual with the symbols shown below. DANGER Warns of a risk, which could