HomeTroller Zee Quick-Start Guide

Size: px
Start display at page:

Download "HomeTroller Zee Quick-Start Guide"

Transcription

1 HomeTroller Zee Quick-Start Guide Congratulations on your purchase! Your HomeTroller Zee is ready to put you in control of your home. Please take a few minutes to read through this guide to familiarize yourself with the steps required to set up your Z-Wave network and your HomeTroller Zee. STEP #1 HomeTroller Zee Initial Setup After you ve created your Z-Wave network, you ll need to install your HomeTroller Zee. Follow these steps: HomeTroller Zee Hardware Installation a) Unpack the HomeTroller Zee, Ethernet cable and AC power supply. b) Connect the Ethernet cable to your HomeTroller Zee and to a network port on your internet router. c) Connect the Z-Stick to one of the USB ports on your HomeTroller Zee d) Connect the AC power adapter to your HomeTroller Zee to begin the boot process. Allow the unit to boot fully (about 1 minute and 45 seconds). Accessing the HomeTroller Zee Web Interface Once the unit boots, you ll need to access the web interface to set the system up. The method below should work with any browser on any device (mobile or desktop). a) Navigate to b) Click the Search button. Your HomeSeer system should now appear at the bottom. c) Click the IP address hyperlink to access your system s web interface. Set Your System Password The system password screen will appear the first time you run your HomeTroller Zee. You MUST set a system password to prevent unauthorized access to your unit. Please do this now by following the prompts on your screen. Activate and Register Your HomeTroller Zee Online Be sure to activate your HomeTroller Zee and register the unit to receive HomeSeer support. To do this, make you re your unit is connected to the internet and follow these steps: a) From the HomeTroller Zee web interface, use the pull down menus to navigate to the General Tab of the Setup Area (TOOLS > Setup) b) Click the Register Online button in the License section of the Setup screen and enter your license codes. Note: License codes are included on a sticker on the bottom of your HomeTroller Zee. Setting the Time Zone and Updating Your HomeTroller Zee Be sure to set the time zone and check for updates and install any that are available. To do this, follow these steps: Page 1

2 a) Access the General Tab of the Setup Area again and scroll to the Location area. Find the Time Zone field and change that to time zone where your HomeTroller Zee is installed. Example: US America/New_York b) From the HomeTroller Zee web interface, use the pull down menus to navigate to the General Tab of the Setup Area (TOOLS > Setup). If an update is available, click the update button near to top of the page and wait for the update to download and install. Your HomeTroller Zee will automatically reboot once the update is installed. Configuring the Wi-Fi Adapter If you ordered the Wi-Fi adapter with your Zee, follow these instructions for setting it up: (You must have HS set up with the Ethernet cable first) a) Connect the Wi-Fi adapter to your HomeTroller with the Ethernet cable plugged in still. b) Access the Network Tab of the Setup section. Locate the Wi-Fi Settings section. c) Enter the SSID (Wi-Fi network name) of your Wi-Fi. (This is case sensitive) d) Choose your encryption type and enter your Wi-Fi password. Keep Use DHCP checked. e) Go to Tools->System->Shutdown System. Once the system is shutdown. Unplug the power and then the Ethernet cable. Now reconnect the power and let the system boot. f) If you go to find.homeseer.com now, it should show another HomeTrollerZEE. This is your new IP address and are all set to use the Wi-Fi adapter. STEP #2 Local/Remote Remote Access MyHS Remote is a free remote tool that will allow you to access the HS3 interface of the HomeTroller from any remote computer via home network (LAN) or the internet (WAN). The HomeTroller can also be accessed locally via IP address and/or computer name. See below for instructions. Accessing Your HomeTroller Locally HS3 can be accessed from any computer on the same local network just by typing in the IP Address (i.e ) of your HomeTroller. Using HomeSeer MyHS Remote Service Welcome to the MyHomeSeer Remote. MyHS will allow you to access your HS3 system from anywhere without having to access your router. There are requirements for MyHS to work. HS3 must be version or later. HSTouch Android client requires or later. Please make sure to update to these versions. It is recommended that you uninstall the application and then reinstall it from the Play Store/iTunes Store. (This guide assumes you have HSTouch Server already set up. If you do not, please refer to the HS3 Quick Start Guide on setting that up). Now, let s get started! To begin using MyHSRemote you will need to register your HS3 software with the connected service. Page 2

3 Registration a) Once the HSTouch has finished installing, go ahead and open it up. You will be prompted with a Log In to MyHS screen. b) Click Register. Your default browser will come forward and load the registration page. c) Enter in the preferred address you would like to use to be tied to your MyHS for the Account Address. This will later be used as your MyHS username. d) Enter a preferred Account Password. You will use this as the password to enter in your MyHS settings. e) The License ID you are asked for is your HS3 licenseid. The same goes for your License Password. (For HomeTroller HS3 users, this is located on the bottom of your unit. For HS3 Software users, this information was ed to you.) f) Click Register. You will receive a confirmation on the next screen unless errors are detected. You will also be ed an that requires a confirmation. Click the link in the . STEP #3 - Z-Wave Network Setup In order to control Z-Wave devices, such as light switches, thermostats, door locks and sensors, they must be included into a Z-Wave network. Follow the steps below to create your Z-Wave network and to include devices. Note: the steps below assume you ve already physically installed Z-Wave devices in your home. Including Externally Powered Devices (wall switches, receptacles, plug-in modules, etc) a) Unpack the enclosed black USB Z-Stick and put it into inclusion mode by pressing and releasing the large round button on one side. A blue LED light around the button will begin blinking slowly. b) While the Z-Stick is in inclusion mode, position it within 1-3 feet of your Z-Wave device. Now press the network button (or paddle) on your Z-Wave device and observe the blinking LED on the Z-Stick. If successful, the LED light will glow solidly for about 2 seconds and then will begin blinking slowly again. Note: If the LED does not glow solidly, the device may need to be reset. Reset the device by following the procedure outlined in Excluding Devices below. c) If you have other Z-Wave devices to add to your network, you may keep the Z-Stick in inclusion mode and add the remaining devices using the procedure above. Once you re finished, tap the button on the Z-Stick again. The LED light will turn off and it will no longer be in inclusion mode. Including Battery Powered Devices (door locks, environmental sensors, etc) Battery operated devices must be included into your Z-Wave network using the HomeTroller Zee web interface. Follow the steps below to include your battery operated device(s). a) Position your battery operated Z-Wave device within 1-3 Feet of your HomeTroller Zee. b) From the web interface, use the pull down menus to navigate to the Z-Wave Controller Management page (PLUG-INS > Z-Wave > Controller Management). c) Locate the Z-Wave Interfaces area and expand the ZStick section. Open the Actions: menu and choose Add/Include a Node. Page 3

4 d) Click the Start button below the Actions menu. Your HomeTroller Zee is now in inclusion mode and is ready to communicate with your battery operated device. e) Activate the network button (or button sequence) on your battery operated device and observe the inclusion process in the green log window. When done, you ll receive an acknowledgement such as Finished with Replication process. Your battery operated device is now included in your Z-Wave network! Excluding Devices Follow the procedure below to (a) reset the device to its factory settings or (b) remove the device from your Z-Wave interface. a) To put the Z-Stick into exclusion mode, press and hold its round button for 3 seconds. The LED light will begin to blink rapidly. b) Position the Z-Stick within 1 3 feet of your Z-Wave device and press the network button or paddle on your Z- Wave device. The blue LED light on your Z-Stick will glow solidly for about 2 seconds and then return to blinking rapidly. Your device has now been reset or removed from your network. STEP #4 Importing, Editing and Controlling Your Z-Wave Devices After you ve created your Z-Wave network, you ll need to import that network into your HomeTroller Zee, so that your devices can be monitored and controlled. Here s how to do that: Importing Z-Wave Devices g) From the web interface, use the pull down menus to navigate to the Z-Wave Controller Management page (PLUG-INS > Z-Wave > Controller Management). h) Locate the Z-Wave Interfaces area and expand the ZStick section. Open the Actions: menu and choose Import Node Info from Controller and Scan Devices. i) Click the Start button below the Actions menu. Your HomeTroller Zee is will now import your device information from the Z-Stick. When done, you ll receive an acknowledgement such as Finished with Z-Wave device synchronization. Your Z-Wave devices may now be monitored and controlled from the HomeTroller Zee! Editing and Controlling Your Z-Wave devices a) From the web interface, use the pull down menus to navigate to the Device Management Page (VIEW > Device Management). Click the Show All button in the upper right hand area of the page. A list of all your devices will now be displayed. b) To edit the name, location and other properties of any device, click the name. c) To control the device, use the buttons in the control column. Page 4

5 STEP #5 Z-Wave Device Configuration With Z-Wave devices, configuration can be done for each device. There are also tools for failed communication with these devices as well. Follow these steps to Configuring Device Settings a) From the web interface, go to your Device Management page and click on the device you wish to configure. b) Click on the Z-Wave tab. c) Here you can Rescan, Remove, Test, Optimize, and Audit the node. Associations can also be set here. d) Expanding the Settings section will allow you to change the wake-up interval for battery operated devices. Here you will also see many settings for different parameters depending on the device. STEP #6 Creating Automation Events Simply put, an automation event consists of an action (or actions) that are set into motion by one or more triggers. Example: Turning on lights at sunset. Trigger = sunset, Action = turning lights on. With HomeTroller Zee, you can quickly and easily create all the events you need. Here s how to create the sunset event above: Creating Events e) From the web interface, use the pull down menus to navigate to the Events page (VIEW > Events). f) Change the event group name from New Group to Lighting. g) Now expand the New Event section and rename the new event to Lights on at Sunset h) In the shaded blue Trigger section, choose The Time Is and then ZEEect The Time is Sunset i) If the shaded green Actions section, choose Control a Device and then ZEEect the device you wish to control and the method of control (on / off) you wish to use. The resulting event will look like this: Remote Access This Quick Start Guide is designed to cover initial setup of the unit for local (LAN) access and control. However, the unit may also be accessed remotely from other computers and mobile devices. Please see the complete online documentation for topics and information on setting up remote access. Page 5

6 STEP #7 Setting up Z-Wave and X10 PROBLEM: HomeTroller Zee includes an automatic port assignment function that's designed to simplify setup for users with a single protocol system (Z-Wave or X10). However, users with a multi-protocol system (Z-Wave and X10) may experience port assignment problems if the Z-Wave or X10 interfaces are detached and reattached to/from the system before being fully configured. If you have a multi-protocol system, follow the configuration steps below to ensure proper port assignment. SOLUTION 1. Navigate to the PLUG-INS > Z-Wave > Controller Management page and disable the Z-Wave interface. If there is a white button with a green checkbox at the top of the area, click it. If there is a yellow button with a red circle, no action is needed. 2. Navigate to the PLUG-INS > Manage page and disable the X10 and Z-Wave plug-ins. 3. Detach the X10 and Z-Wave interfaces from your HomeTroller Zee. Leave these detached until prompted to reattach below. 4. Navigate to the TOOLS > System > Restart System page and click the [Restart...] button to restart your HomeTroller Zee. 5. After the Zee has fully booted, attach the X10 interface cable to one of the USB ports. Navigate to the PLUG-INS > Manage page, ZEEect the available port and enable the X10 plug-in. Test the X10 plugin by creating an X10 device in the device management page. 6. If X10 testing was successful, navigate to then PLUG-INS > Manage page and enable the Z-Wave plug-in. NOW, attach to Z-Stick to the remaining USB port. The system will reboot and assign a port to the ZStick. 7. Once the box has restarted, navigate to PLUG-INS > Z-Wave > Controller Management page and click the yellow button with the red crossed circle to enable the Z-Stick interface. At this point, both interfaces should be properly connected and fully functional. Note: To avoid future port assignment problems, do not disconnect the X10 interface cable. STEP #8 HSTouch Server Setup After you have successfully connected to your Wi-Fi network, you will need to make sure HSTouch Server is properly set up before connecting the client to your HomeSeer system. Follow the instructions below to set up HSTouch Server. a) Go to the Plug-in s menu within your HomeSeer Web Control and click on Manage. b) If HSTouch Server is not installed follow these steps, otherwise skip to step f c) Click on Additional Interfaces to expand the plug-in updater. d) Scroll down to User Interfaces and expand that. Check the box next to HomeSeer HSTouch Sever. e) Scroll back up and click on Download and Install. f) Now that HSTouch Sever is installed we will need to enable it. Underneath the Enable column click on the red toggle. It should become green with a check mark in it. Page 6

7 g) HSTouch Server is now enabled. You can now go into HSTouch on your device to configure HSTouch. Setting Up IP Cameras For setting up an IP Camera within HS3, follow the instructions below. Note that all Foscam IP Netcams will be automatically detected by HS3 whereas other cameras will not. a) Now that HStouch is enabled you should be able to go to Plug-ins->HSTouch Server->HSTouch. b) At the bottom you will see an IP Camera section. All Foscam cameras will automatically show up here. Yoou will need to enter the username and password for each camera. c) For other branded cameras click the Green Plus to add a camera. d) Here you can name the camera, add the snapshot url (this will include the username and password), and then set up pan/tilt controls. STEP #9 HSTouch Client Setup Here you will configure your settings and connect to your HomeSeer system to allow for control from your device. Follow the instructions below to set up the HSTouch Client. For ios, please go to your Settings App first. a) HSTouch will prompt you to ZEEect a server or settings. Click settings. (The first launch will require an initial setup.) A menu on the bottom right will pop up. Click Settings again. (This menu can also be used to switch between servers, go to settings, or exit the app.) b) Within the settings you are given multiple options. Servers 1-4 allow you to configure each server for different locations. c) ZEEect the server you would like to have as your Home setup. d) Configure a Label for that HomeSeer system. Click Address to enter the IP Address or Domain of the HomeSeer System. e) Now that you have set up the connection address, go ahead and enter in your Username and Password for that server. There is no need to change the port. f) You can follow steps c-e for the remaining 3 connections. g) If you go back to the main settings screen, there are other options for setting up HSTouch. Page 7

8 h) Connection Mode allows you to choose a default connection for each time you start HSTouch. (HSTouch will no longer prompt to choose a connection at the beginning.) i) Dim Systembar allows for the bottom systembar to be dimmed. Font Scaling allows for changing the scaling factor. j) Auto Size allows for auto-sizing of the project being used for your device. Client Name will allow you to change the name of your device s HSTouch Client. (For use with HSTouch Designer). Zipcode is used for weather. k) Now that your Client has been set up, go back to the Main Screen and go to the settings menu on the bottom right. Click Exit. Now go to your app drawer and click HSTouch. This will allow for any changes to take place. l) You are now ready to control your home via your device! Setting Up MyHS Remote The next step involves going into the HSTouch application and entering in your Account Username and Account Password. a) Open up the HSTouch application. It will give you the same prompt as earlier to Log In to MyHS. b) The you used to register is your Username and the password you used will be used as the Password. c) Click Ok and HSTouch will now connect. d) HSTouch will now always connect through MyHS when launching. This will work from any location and any network. STEP #10 HS3 Recovery (911) The ability to fix any settings related issues or update issues with your Zee can now be address by adding :911 to the end of your IP address as the port number. This Recovery page will frequently be updated with new ways to fix your Zee. This page will only work when on the local network. 911 requires HS3 version or later. Option 1: Use option 1 if you cannot access your system due to forgetting username, changing settings that cause HS3 to not boot correctly, or enabling a plug-in that may cause HS3 to crash. Option 2: Use option 2 if you want to revert back to an update or update to the latest version. Update HS Recovery Utility: Use this to check for updates to your Recovery page with added recovery options. Return to HS: This will bring you back to find.homeseer.com to find your HS3 system. Page 8

9 Page 9

10 Icon Legend for HS3 This is a list of the icons that are found in HS3 with a description of their function. Note: Some buttons are multi-functional. ICON DESCRIPTION Add / Delete Copy Event Standard Editing / Advanced Editing Toggle Edit Mode Enabled / Disabled Error communicating Expand / Collapse Section Marked Devices Shown/Header and Menus Shown Marked Devices Hidden/Header and Menus Not Shown Access Log Settings Poll Devices for Status Reset Layout to Default Run Event Devices Ungrouped / Grouped Add a Keyword or Pair Group Conditions are used / not being used Expand Device Management Page / Collapse Device Management Page *If you want to know what that button will do, just hover your cursor over the icon and small text will show to provide definition. Page 10

11 Troubleshooting Your HomeTroller Zee Symptom Cause Solution Ac Adapter Unplugged Plug-In Adapter Unit Won t Power On AC Adapter Bad Power Cable Bad Contact Homeseer USB Hardware Conflict Detach USB Device And Reboot Unit Powers On But Won t Boot Software Failure Hardware Failure Contact Homeseer Device Was Previously Installed On Use Exclude Device Procedure To Z-Wave Devices Cannot Be Included Another Z-Wave Network Reset Device, Then Try To Include Into Z-Wave Network Device Failure Replace Device Z-Stick Failure Contact Homeseer Hometroller Zee Not Powered On Power Unit On Hometroller Zee Not Fully Booted Wait 2 Minutes For Unit To Boot HSDiscover Cannot Locate Device Hometroller Zee Not Connected To Connect Unit To Router And Reboot LAN Door Locks Won t Include Or Can t Exclude Devices and Repeat Be Controlled Inclusion Process Incorrect Or Procedure Outline In Including Incomplete Battery Powered Devices Section Sensors Won t Include Or Can t Be Monitored Wi-Fi not Connecting Incorrect Wi-Fi SSID or Password Contact HomeSeer All Other Problems Contact HomeSeer HomeSeer Technologies 10 Commerce Park North, Unit #10 Bedford, NH Page 11

HomeTroller SEL Getting Started Guide

HomeTroller SEL Getting Started Guide HomeTroller SEL Getting Started Guide Congratulations on your purchase! Your HomeTroller SEL is ready to put you in control of your home. Please take a few minutes to read through this guide to familiarize

More information

HomeTroller S6 Quick-Start Guide

HomeTroller S6 Quick-Start Guide HomeTroller S6 Quick-Start Guide Congratulations on your purchase! Your HomeTroller S6 is ready to put you in control of your home. Please take a few minutes to read through this guide to familiarize yourself

More information

HomeTroller Zee S2 Getting Started Guide

HomeTroller Zee S2 Getting Started Guide HomeTroller Zee S2 Getting Started Guide Congratulations on your purchase! Your HomeTroller Zee S2 is ready to put you in control of your home. Please take a few minutes to read through this guide to familiarize

More information

HomeTroller S6 Getting Started Guide

HomeTroller S6 Getting Started Guide HomeTroller S6 Getting Started Guide Congratulations on your purchase! Your HomeTroller S6 is ready to put you in control of your home. Please take a few minutes to read through this guide to familiarize

More information

HomeTroller SEL Getting Started Guide

HomeTroller SEL Getting Started Guide HomeTroller SEL Getting Started Guide Congratulations on your purchase! Your HomeTroller SEL is ready to put you in control of your home. Please take a few minutes to read through this guide to familiarize

More information

HomeTroller S6 Getting Started Guide

HomeTroller S6 Getting Started Guide HomeTroller S6 Getting Started Guide Congratulations on your purchase! Your HomeTroller S6 is ready to put you in control of your home. Please take a few minutes to read through this guide to familiarize

More information

TROUBLESHOOTING GUIDE

TROUBLESHOOTING GUIDE TROUBLESHOOTING GUIDE Difficulty installing apps on LeapFrog Epic tablet Q: While purchased apps appear in the App Manager on the "Not installed" tab, the Install button is grayed out. How can I install

More information

IpAlarm Module Set Up VirtuAlarm model

IpAlarm Module Set Up VirtuAlarm model Page 1 IpAlarm Module Set Up VirtuAlarm model Note: This device is shipped configured for Ethernet connectivity. To use in this mode, connect the BLUE Jack (marked WAN) to your router and wait at least

More information

Amcrest Eco HDCVI DVR Quick Start Guide

Amcrest Eco HDCVI DVR Quick Start Guide Amcrest Eco HDCVI DVR Quick Start Guide Version 1.0.1 Revised August 13th, 2015 Welcome Thank you for purchasing our Amcrest Eco HDCVI DVR! This quick start guide will help you become familiar with our

More information

IpAlarm Module Set Up

IpAlarm Module Set Up Page 1 IpAlarm Module Set Up Note: This device is shipped configured for Ethernet connectivity. To use in this mode, connect the BLUE Jack (marked WAN) to your router and wait for the LEDs to stabilize.

More information

35 Constitution Dr, Suite C Bedford, NH

35 Constitution Dr, Suite C Bedford, NH HomeSeer HS2 Getting Started Guide HomeSeer Technologies LLC 35 Constitution Dr, Suite C Bedford, NH 03110 www.homeseer.com Welcome to HomeSeer! This getting started guide is for use with the HS2 version

More information

HUB FAQ Wink HUB - F W A ink HUB - F Q 1 A

HUB FAQ Wink HUB - F W A ink HUB - F Q 1 A FAQ Wink - FAQ 1 How do I connect my Wink to my phone? 1. Download the Wink App from the Apple App Store or Google Play and follow the in-app instructions to sign up or login. 2. Select Wink and follow

More information

Quick Installation Guide

Quick Installation Guide Model: FI8916W Quick Installation Guide Indoor Pan/Tilt Wireless IP Camera Black White For Windows OS ------- Page 1 For MAC OS ------- Page 16 ShenZhen Foscam Intelligent Technology Co., Ltd Quick Installation

More information

Touch Screen Digital Signage (Network) User Manual

Touch Screen Digital Signage (Network) User Manual Touch Screen Digital Signage (Network) User Manual Manual Version: AOEF-DS (8350) Contents: 1. Installing Digital Signage App... 2 2. Getting Your Screen Online... 7 3. Menus... 11 3.1 Home Screen... 11

More information

linkzone User ManUal

linkzone User ManUal LINKZONE User Manual Getting to Know Your Mobile Hotspot Power key WPS key LED indicator USB jack LED Description Part Power key WPS key LED indicators Charging / USB Port Reset Reboot Description Hold

More information

Drobo 5N2 User Guide

Drobo 5N2 User Guide Drobo 5N2 User Guide Contents 1 Drobo 5N2 User Guide... 6 1.1 Before You Begin... 7 1.1.1 Product Features at a Glance... 8 1.1.2 Checking Box Contents...10 1.1.3 Checking System Requirements...11 1.1.3.1

More information

Quick Installation Guide

Quick Installation Guide V50.02 Model: FI8918W Quick Installation Guide Indoor Pan/Tilt Wireless IP Camera Black White For Windows OS ------- Page 1 For MAC OS ------- Page 14 Quick Installation Guide For Windows OS Package Contents

More information

HP Notebook PCs - Keyboard and TouchPad or ClickPad Guided Troubleshooter

HP Notebook PCs - Keyboard and TouchPad or ClickPad Guided Troubleshooter HP Notebook PCs - Keyboard and TouchPad or ClickPad Guided Troubleshooter This document applies to HP notebook computers. The keyboard, TouchPad, or ClickPad on your laptop is not working as expected:

More information

Please note, instructions in this guide are based on a PC running Windows 7. Please adapt the actions to suit your operating system.

Please note, instructions in this guide are based on a PC running Windows 7. Please adapt the actions to suit your operating system. Please note, instructions in this guide are based on a PC running Windows 7. Please adapt the actions to suit your operating system. Please follow these steps to ensure that any changes made by your previous

More information

Getting Started with your new TiO System. Get to know TiO. Welcome to your brand new TiO system! Your TiO system consists of 3 main components:

Getting Started with your new TiO System. Get to know TiO. Welcome to your brand new TiO system! Your TiO system consists of 3 main components: Quick Start Guide Getting Started with your new TiO System Welcome to your brand new TiO system! This guide will show you the basics of owning a TiO system. First-time setup of a TiO system Downloading

More information

DSL-G624T. Wireless ADSL Router. If any of the above items is missing, please contact your reseller. This product can be set up using any

DSL-G624T. Wireless ADSL Router. If any of the above items is missing, please contact your reseller. This product can be set up using any This product can be set up using any current web browser, i.e., Internet Explorer 6x or Netscape Navigator 7x. DSL-G624T Wireless ADSL Router Before You Begin 1. If you purchased this Router to share your

More information

AirServer Connect User Guide

AirServer Connect User Guide 1 Contents Welcome... 3 Unique features... 3 Set up your AirServer Connect... 4 The Home Screen... 5 Navigating Menus... 5 Configuring Basic Settings... 6 Screen Mirroring Methods... 7 Airplay... 7 Mac...

More information

Amcrest 960H DVR Quick Start Guide

Amcrest 960H DVR Quick Start Guide Amcrest 960H DVR Quick Start Guide Version 2.0.2 Revised July 22, 2015 Welcome Thank you for purchasing our Amcrest 960H DVR! This quick start guide will help you become familiar with our DVR in a very

More information

Table of Contents. Chapter 1 Introduction Chapter 2 Quick Install... 7

Table of Contents. Chapter 1 Introduction Chapter 2 Quick Install... 7 AVA-88 WELCOME Congratulations on purchasing the AVA-88. The AVA-88 integrates multiple complicated control, automation and internet protocols into one simple plug-and-play device. It is a central controller

More information

Networking the printer

Networking the printer Networking the printer General networking Networking overview A network is a collection of devices such as computers, printers, Ethernet hubs, wireless access points, and routers connected together for

More information

Setup Guide for Wi-Fi Hotspot Boosting Kit

Setup Guide for Wi-Fi Hotspot Boosting Kit Setup Guide for WI-KIT-02 Wi-Fi Hotspot Boosting Kit Congratulations on purchasing the WI-KIT-02, this contains everything you need to be able to connect to Wi-Fi at a camp site / marina / other location.

More information

Document Number: /4/2012

Document Number: /4/2012 Copyright 2012 icontrol Networks, Inc. All rights reserved. No reproduction in whole or in part without prior written approval. icontrol Networks, icontrol, and icontrol logo design are pending trademarks

More information

Network USB over IP Server With 1-USB2.0 Port. User Manual V1.0

Network USB over IP Server With 1-USB2.0 Port. User Manual V1.0 Network USB over IP Server With 1-USB2.0 Port User Manual V1.0 1 2 TABLE OF CONTENTS COPYRIGHT...4 1. INTRODUCTION...5 PRODUCT OVERVIEW...5 COMPONENTS AND FEATURES...5 HARDWARE INSTALLATION...5 2. THE

More information

Table of Contents. Camera Anatomy... pg 1. Package Contents... pg 2. Camera Assembly... pg 3. Account Login... pg 5. Adding a New Camera...

Table of Contents. Camera Anatomy... pg 1. Package Contents... pg 2. Camera Assembly... pg 3. Account Login... pg 5. Adding a New Camera... Table of Contents Camera Anatomy... pg 1 Package Contents... pg 2 Camera Assembly... pg 3 Account Login... pg 5 Adding a New Camera... pg 6 Wireless Configuration... pg 9 WPS Enabled Routers... pg 13 Technical

More information

How to manually set up EW-7228APn to extender wireless range

How to manually set up EW-7228APn to extender wireless range How to manually set up EW-7228APn to extender wireless range 1. Find out the IP address of your computer. Have your computer get on Internet as normally, without EW-7228APn turning on. If you use a Windows

More information

Congratulations on the purchase of your new Clover Mini

Congratulations on the purchase of your new Clover Mini Congratulations on the purchase of your new Clover Mini Set Up the Hardware What s included The white USB cord provided can be used to plug into the Hub and connected to other accessories (such as the

More information

Bush Baby Wi-Fi Wall Outlet Hidden Camera

Bush Baby Wi-Fi Wall Outlet Hidden Camera Bush Baby Wi-Fi Wall Outlet Hidden Camera SKU: BBWiFiWallOutlet 1 Version 1.1 THANK YOU FOR PURCHASING THE BBWIFIWALLOUTLET Please read this manual before operating the BBWIFIWALLOUTLET and keep it handy.

More information

Connecting to Director. Before setting up Director for the first time run through the check list below:

Connecting to Director. Before setting up Director for the first time run through the check list below: Connecting to Director Before setting up Director for the first time run through the check list below: 1.Are both the lights and router within reasonable distance from Director and all components preferably

More information

SAS Mobile BI 8.15 for Android: Help

SAS Mobile BI 8.15 for Android: Help SAS Mobile BI 8.15 for Android: Help Welcome Getting Started How Do I Use the App? Check out the new features. View the videos: SAS Mobile BI for Android playlist on YouTube Use TalkBack? Learn the specialized

More information

Android (A1000) Y4 Classrooms: User Guide

Android (A1000) Y4 Classrooms: User Guide Android (A1000) Y4 Classrooms: User Guide Provided by the SDUSD Ed Tech Team i21 2014 Teachers - Version 3.25.2014 Table of Contents Basic Functionality... Navigation Tips... Taking a Screenshot... Finding

More information

Sotion Wireless Camera. User Manual.

Sotion Wireless Camera. User Manual. Sotion Wireless Camera User Manual Email: Help@sotiongroup.com App Download & Installation The camera is compatible with Wi-Fi 2.4 GHz only, please connect camera to 2.4 GHz Wi-Fi. Make sure your network

More information

nettalk DUO WiFi Configuration (using an Android smartphone)

nettalk DUO WiFi Configuration (using an Android smartphone) nettalk DUO WiFi Configuration (using an Android smartphone) Step 1. Activate your Device a. Locate your username and password inside of the box. b. Go to www.nettalk.com/activate and follow the activation

More information

What s in the Box Get Started Hardware Installation For Mobile Device Set Up Camera... 6

What s in the Box Get Started Hardware Installation For Mobile Device Set Up Camera... 6 Quick Start Guide Table of Contents What s in the Box... 1 Get Started... 1 Hardware Installation... 2 For Mobile Device... 2 Set Up Camera... 6 Set Up Wi-Fi Without Network Cable... 8 View in Windows

More information

Quick Installation Guide

Quick Installation Guide V47.01 Model: FI8909W Quick Installation Guide Indoor Wireless IP Camera Black White For Windows OS ------- Page 1 For MAC OS ------- Page 16 ShenZhen Foscam Intelligent Technology Co., Ltd Quick Installation

More information

CLEARVIEW KIT INSTALLATION GUIDE

CLEARVIEW KIT INSTALLATION GUIDE CLEARVIEW KIT INSTALLATION GUIDE Kit contents 1. Recorder with power supply 2. Camera Cables 3. Cameras 4. Mouse ** Display monitor and HDMI cable not included Remove recorder from the Kit and look over

More information

Contents. 2 WiFi user guide

Contents. 2 WiFi user guide WiFi user guide Contents Welcome.... 3 What this guide provides... 3 Get to know your Nokia WiFi components... 4 Nokia WiFi Gateway 3........................................................... 4 Nokia

More information

1. Charging. 2. In-app Setup. 3. Physical Installation. 4. Features. 5. Troubleshooting

1. Charging. 2. In-app Setup. 3. Physical Installation. 4. Features. 5. Troubleshooting Spotlight Cam Smart Security at Every Corner of Your Home Your new Spotlight Cam lets you extend the Ring of Security around your entire property. Now, you ll always be the first to know when someone s

More information

Everything in your eyes. ismartviewpro. (For iphone) User Manual VER 5.0

Everything in your eyes. ismartviewpro. (For iphone) User Manual VER 5.0 IP Cloud Network Camera Everything in your eyes ismartviewpro (For iphone) User Manual 2018-01 VER 5.0 1. ismartviewpro Summary ismartviewpro (iphoneversion) is developed application software based on

More information

Thank you for purchasing the Mobile WiFi. This Mobile WiFi brings you a high speed wireless network connection.

Thank you for purchasing the Mobile WiFi. This Mobile WiFi brings you a high speed wireless network connection. Quick Start Thank you for purchasing the Mobile WiFi. This Mobile WiFi brings you a high speed wireless network connection. This document will help you understand your Mobile WiFi so you can start using

More information

power port make sure the ac adapter is plugged into the correct port Make sure to include at the beginning.

power port make sure the ac adapter is plugged into the correct port Make sure to include  at the beginning. Quickstart Guide If you have a blank SD card, you may insert it into the camera. To set up your camera for use on the network, connect the camera's wired network port to a router. Connect the AC adapter

More information

Quick Installation Guide

Quick Installation Guide V46.01 Model: FI8909W Quick Installation Guide Indoor Wireless IP Camera Black White For Windows OS ------- Page 1 For MAC OS ------- Page 11 ShenZhen Foscam Intelligent Technology Co., Ltd Quick Installation

More information

HSPA+ WiFi Router with Voice

HSPA+ WiFi Router with Voice NETCOMM LIBERTY SERIES HSPA+ WiFi Router with Voice 3G22WV Quick Start Guide This router has been designed to be placed on a desktop. All of the cables exit from the rear for better organization. The LED

More information

QUICK START GUIDE QT IP CAMERA & NVR BUNDLE ENGLISH

QUICK START GUIDE QT IP CAMERA & NVR BUNDLE ENGLISH QUICK START GUIDE QT IP CAMERA & NVR BUNDLE ENGLISH Table of Contents Welcome What s Included...3 Understanding your NVR...4 Get Connected Registration...5 Connect Your Cameras...5 Connect NVR to Display...6

More information

G-240WZ-A GPON Residential Gateway. A-240Z-A Ethernet Residential Gateway. Nokia Smart Home user guide

G-240WZ-A GPON Residential Gateway. A-240Z-A Ethernet Residential Gateway. Nokia Smart Home user guide G-240WZ-A GPON Residential Gateway A-240Z-A Ethernet Residential Gateway Nokia Smart Home user guide Introduction This manual shows you how to setup and manage your Nokia Smart Home. You ll be guided step

More information

WHEN YOU HAVE NO INTERNET ACCESS, WHAT NOW?

WHEN YOU HAVE NO INTERNET ACCESS, WHAT NOW? WHEN YOU HAVE NO INTERNET ACCESS, WHAT NOW? Let s quickly outline the steps first, then we ll go into detail on each one: 1. Confirm other devices can t connect 2. Reboot your computer 3. Unplug your modem

More information

Product Manual. Version PROMISE Technology, Inc. All Rights Reserved.

Product Manual. Version PROMISE Technology, Inc. All Rights Reserved. Product Manual Version 2.0 2016 PROMISE Technology, Inc. All Rights Reserved. Contents Table of Contents Introduction 1 Unpacking 1 Requirements for Apollo setup and use 1 Back of Apollo 2 Front of Apollo

More information

USER GUIDE. for ios Version 1. alula.net ALULA 1

USER GUIDE. for ios Version 1. alula.net ALULA 1 USER GUIDE for ios Version 1 alula.net 1-888-88-ALULA 1 1. GETTING STARTED 3 2. DOWNLOAD THE ALULA APP 3 3. SIGN IN 3 4. 4. LOCATIONS 4 5. MAIN DASHBOARD SCREEN 5 5.1. Application Menu 5 5.3. Feature Menus

More information

Catalogue. Assembling... 1 Unpack Charge the Battery Install the Memory Card Product Basics Buttons and Connections...

Catalogue. Assembling... 1 Unpack Charge the Battery Install the Memory Card Product Basics Buttons and Connections... Catalogue Assembling... 1 Unpack... 1 Charge the Battery... 1 Install the Memory Card... 1 1 Product Basics... 2 1.1 Buttons and Connections... 2 1.2 Start Up and Shut Down... 2 2 Introduction of Google

More information

Fix Home Network. Thousands of satisfied users! Easy steps to setup Wireless router with Cable or DSL internet service provider.

Fix Home Network. Thousands of satisfied users! Easy steps to setup Wireless router with Cable or DSL internet service provider. Fix Home Network Thousands of satisfied users! Easy steps to setup Wireless router with Cable or DSL internet service provider. Copyright, Legal Notice and Disclaimer: This publication is protected under

More information

User Manual. Microdigital IP-cameras with built-in Ivideon software. Cloud Video Surveillance

User Manual. Microdigital IP-cameras with built-in Ivideon software. Cloud Video Surveillance User Manual Microdigital IP-cameras with built-in Ivideon software Cloud Video Surveillance Table of Contents Ivideon: basic concepts 3 What is Ivideon? 3 What is an IP camera with built-in Ivideon software?

More information

HooToo IP Camera User Manual(part two)

HooToo IP Camera User Manual(part two) HooToo Inc. HooToo IP Camera User Manual(part two) For Model: HT-IP210P Published by SunvalleyTek Group 2014/9/14 Content 1. IPCamClient (windows software)...3 Set up...3 CAM... 13 Local Setting... 13

More information

Amcrest 650 TVL DVR Quick Start Guide

Amcrest 650 TVL DVR Quick Start Guide Amcrest 650 TVL DVR Quick Start Guide Version 1.0.2 Revised May 9 th, 2016 Welcome Thank you for purchasing our Amcrest 650 TVL DVR! This quick start guide will help you become familiar with our DVR in

More information

Bush Baby Alarm Clock With WiFi Hidden Camera

Bush Baby Alarm Clock With WiFi Hidden Camera Bush Baby Alarm Clock With WiFi Hidden Camera SKU: BBWiFiAlarmClock 1 Version 1.1 THANK YOU FOR PURCHASING THE BBWIFIALARMCLOCK Please read this manual before operating the BBWiFiAlarmClock and keep it

More information

Quick Start. MyAir4 User Manual. This section will give you a brief description about each of the buttons found on the home screen.

Quick Start. MyAir4 User Manual. This section will give you a brief description about each of the buttons found on the home screen. User Manual Quick Start... 3 HOME... 4 SIMPLE TIMER... 4 AIR CON... 5 ZONES... 6 PROGRAMS... 7 HELP... 11 SETTINGS... 12 MyZone - (optional feature)... 15 Constant Zones... 17 Android Tablet... 18 Smart

More information

This handbook contains important security measures and product information, to help avoid accidents. Please

This handbook contains important security measures and product information, to help avoid accidents. Please MANUAL Attention: This handbook contains important security measures and product information, to help avoid accidents. Please make sure to read the manual carefully before using the device. Do not store

More information

Table of Contents... ii. GO AHEAD BRING YOUR OWN DEVICE TO WORK... 1 Requirements... 1

Table of Contents... ii. GO AHEAD BRING YOUR OWN DEVICE TO WORK... 1 Requirements... 1 Table of Contents... ii GO AHEAD BRING YOUR OWN DEVICE TO WORK... 1 Requirements... 1 1: Use AT&T Toggle Applications on an iphone or ipad... 1 AT&T Toggle... 2 Set up Work Email within AT&T Toggle...

More information

Smart Security at Every Corner of Your Home

Smart Security at Every Corner of Your Home Spotlight Cam Smart Security at Every Corner of Your Home Your new Spotlight Cam lets you extend the Ring of Security around your entire property. Now, you ll always be the first to know when someone s

More information

EN ES FR. Quick Start Guide HGWIP-711. HOMEGUARD MODEL HGWIP-711

EN ES FR. Quick Start Guide HGWIP-711. HOMEGUARD MODEL HGWIP-711 EN ES FR RO HGWIP-711 Quick Start Guide HOMEGUARD 2016 www.homeguardworld.com support@homeguardworld.com MODEL HGWIP-711 GIVES YOU PEACE OF MIND WHEREVER YOU ARE HOME Surveillance CHILDREN Playing/Sleeping

More information

WRE6505 v2. User s Guide. Quick Start Guide. Wireless AC750 Range Extender. Default Login Details. Version 1.00 Edition 1, 10/2016

WRE6505 v2. User s Guide. Quick Start Guide. Wireless AC750 Range Extender. Default Login Details. Version 1.00 Edition 1, 10/2016 WRE6505 v2 Wireless AC750 Range Extender Version 1.00 Edition 1, 10/2016 Quick Start Guide User s Guide Default Login Details Web Address http://zyxelsetup http://dhcp-assigned IP www.zyxel.comhttp://192.168.1.2

More information

USER GUIDE. for Android Version 1. alula.net ALULA 1

USER GUIDE. for Android Version 1. alula.net ALULA 1 USER GUIDE for Android Version 1 alula.net 1-888-88-ALULA 1 1. GETTING STARTED 3 2. DOWNLOAD THE ALULA APP 3 3. SIGN IN 3 4. LOCATIONS 4 5. MAIN DASHBOARD SCREEN 5 5.1. Application Menu 5 5.2. Feature

More information

LeFun IP Camera Quick Install Guide

LeFun IP Camera Quick Install Guide LeFun IP Camera Quick Install Guide Website: www.lefunsmart.com E-mail: support@lefunsmart.com Catalog 1. Introduction... 2 1.1. Thank you for Choosing LeFun IP Camera... 2 1.2. Introducing LeFun IP Camera...2

More information

Getting Started. Activation Process. G450 Overview

Getting Started. Activation Process. G450 Overview ntrusion Started G450 Home Control Gateway Getting Getting Started This Home Control Gateway is a controller that supports home automation devices within a Home Control ecosystem. Home automation devices

More information

Welcome to ThinkEssentials

Welcome to ThinkEssentials User s Manual Welcome to ThinkEssentials Figure 1: Sample room and device layout with ten devices ThinkEssentials software includes the following features: Set up and control up to 230 Z-Wave devices Draw

More information

Zavio P5111/ P5116/ P5210 Quick Installation Guide

Zavio P5111/ P5116/ P5210 Quick Installation Guide 86085M2000010 Zavio P5111/ P5116/ P5210 Quick Installation Guide Installation Steps Please follow the installation steps below to set up your P5111 / P5116/ P5210 Day/Night Pan/Tilt IP Camera. Check the

More information

MARQUE: GARMIN REFERENCE: EX FRS CODIC: NOTICE

MARQUE: GARMIN REFERENCE: EX FRS CODIC: NOTICE MARQUE: GARMIN REFERENCE: EX3800-100FRS CODIC: 4121198 NOTICE Model EX3800 User Manual May 2015 202-11488-01 350 East Plumeria Drive San Jose, CA 95134 USA Support Thank you for selecting NETGEAR products.

More information

N150 Wireless Router WNR1000 Setup Manual

N150 Wireless Router WNR1000 Setup Manual N150 Wireless Router WNR1000 Setup Manual January 2009 208-10430-01 v1.0 2009 by NETGEAR, Inc. All rights reserved. Trademarks NETGEAR and the NETGEAR logo are registered trademarks, and RangeMax and Smart

More information

Quick Setup Guide - AirStation Draft-N WZR-G300N Nfiniti Wireless Router & AP

Quick Setup Guide - AirStation Draft-N WZR-G300N Nfiniti Wireless Router & AP Quick Setup Guide - AirStation Draft-N WZR-G300N Nfiniti Wireless Router & AP Package Contents WZR-G300N AirStation Base Stand AC Adapter and Power Cable CAT5 LAN cable Utility CD with Manual Quick Setup

More information

WELCOME. For customer support or any inquiries, please visit our web site at or contact us at

WELCOME. For customer support or any inquiries, please visit our web site at  or contact us at WELCOME Congratulations on purchasing the GBF Smart Four Wire Intercom System. Our factory engineers were the first to enable multiple security cameras being monitored through a smart mobile device and

More information

If you get stuck at any point, please let us know! We love talking to our customers! You can reach us at the number below:

If you get stuck at any point, please let us know! We love talking to our customers! You can reach us at the number below: Thank you for purchasing the HomeMinder Remote Video and Temperature Monitoring System. We wrote these instructions so you can get the most out of your HomeMinder, regardless of your technical knowledge.

More information

User Manual HIGHPOWER TM TOUCH SCREEN WI-FI RANGE EXTENDER S1

User Manual HIGHPOWER TM TOUCH SCREEN WI-FI RANGE EXTENDER S1 User Manual HIGHPOWER TM TOUCH SCREEN WI-FI RANGE EXTENDER S1 1 Table of Contents INTRODUCTION...4 Product view...4 Package Contents...5 Product Description...5 SETUP GUIDE (TOUCH SCREEN)...6 Find a Setup

More information

Quick Install Guide. Model: PLC-223W, PLC-233W

Quick Install Guide. Model: PLC-223W, PLC-233W Quick Install Guide Model: PLC-223W, PLC-233W This installation guide provides basic instructions for installing the PLC-213W/ PLC-223W/PLC-233W indoor wireless IP camera on your network. By following

More information

Quick Start. AC1200 WiFi Range Extender Model EX6150

Quick Start. AC1200 WiFi Range Extender Model EX6150 Quick Start AC1200 WiFi Range Extender Model EX6150 Getting Started The NETGEAR WiFi Range Extender increases the distance of a WiFi network by boosting the existing WiFi signal and enhancing the overall

More information

Introduction. MyAir5 User Guide

Introduction. MyAir5 User Guide User Guide Introduction... 3 Mode Page... 4 Zones Page... 10 Plans Page... 13 Setup Page... 17 Constant Zones... 19 Android Tablet... 20 Smart Phone Control Quick Setup Guide... 21 Network Troubleshooting...

More information

INNOV.NET PTY LTD. User guide

INNOV.NET PTY LTD. User guide User guide 0 Contents Compatibility... 1 What s in the package?... 1 Add device... 2 Legend... 2 Meaning of the LED indicators... 2 Setup the RM Mini 3... 3 Setup e-control on your smartphone... 3 How

More information

The following documents are included with your Sony VAIO computer.

The following documents are included with your Sony VAIO computer. Documentation The following documents are included with your Sony VAIO computer. Printed Documentation Quick Start Guide Describes the process from unpacking to starting up your VAIO. Troubleshooting and

More information

Using AORUS Notebook for the First Time

Using AORUS Notebook for the First Time Congratulations on your purchase of the AORUS Notebook! This Manual will help you to get started with setting up your notebook. For more detailed information, please visit our website at http://www.aorus.com.

More information

Installing the Linksys app on your Android device via the Google Play Store and Google Play Website

Installing the Linksys app on your Android device via the Google Play Store and Google Play Website User Guide Installing the Linksys app on your Android device via the Google Play Store and Google Play Website The Linksys app is a free mobile application that allows you to securely access your home

More information

1900AC. Digital TV box. User Manual.

1900AC. Digital TV box. User Manual. 1900AC Digital TV box User Manual http://www.mygica.com 1 2 3 4 Quick Setup Guide 8 8 1 5 6 7 1. USB 2.0 Port 3. Reset 5. LAN Port 7. DC Input 2. Micro SD Port 4. HDMI Port 6. SPIDF Port 8. Wi-Fi Antenna

More information

Saviour App User Manual. User Manual to use app. This documents describe the Saviour app functionalities for end user.

Saviour App User Manual. User Manual to use app. This documents describe the Saviour app functionalities for end user. Saviour App User Manual User Manual to use app This documents describe the Saviour app functionalities for end user. Introduction This document describes the Saviour app to use Saviour Indoor, Outdoor

More information

Congratulations on the purchase of your new Clover Mobile

Congratulations on the purchase of your new Clover Mobile Congratulations on the purchase of your new Clover Mobile Set Up the Hardware What s included Optional Accessories USB wall charger USB cable Clover Mobile Dock Clover Mobile Printer Clover Mobile Clover

More information

WRE2206. User s Guide. Quick Start Guide. Wireless N300 Range Extender. Default Details. Version 1.00 Edition 1, 01/2015

WRE2206. User s Guide. Quick Start Guide. Wireless N300 Range Extender. Default Details. Version 1.00 Edition 1, 01/2015 WRE2206 Wireless N300 Range Extender Version 1.00 Edition 1, 01/2015 Quick Start Guide User s Guide Default Details Web Address http://zyxelsetup OR http://192.168.1.2 www.zyxel.com User Name admin Password

More information

POS Android Digital Advertising Display (Network) Hardware User Manual

POS Android Digital Advertising Display (Network) Hardware User Manual POS Android Digital Advertising Display (Network) Hardware User Manual Manual Version POSW3.0 Safety Instructions Please keep the display away from any heat sources. Place the display in a stable and well-ventilated

More information

Thank You for Choosing the CRICKET CROSSWAVE

Thank You for Choosing the CRICKET CROSSWAVE CRICKET CROSSWAVE Thank You for Choosing the CRICKET CROSSWAVE The supported functions and actual appearance depend on the product you purchased. The following pictures are provided for illustration only.

More information

DSL-504T ADSL Router. CD-ROM (containing User Manual) Ethernet Cable (CAT5 UTP) ADSL Cable (For AUS 200CM) Power Adapter

DSL-504T ADSL Router. CD-ROM (containing User Manual) Ethernet Cable (CAT5 UTP) ADSL Cable (For AUS 200CM) Power Adapter This product can be set up using any current web browser, i.e., Internet Explorer 6 or Netscape Navigator 6.2.3. DSL-504T ADSL Router Before You Begin 1. If you purchased this Router to share your high-speed

More information

Electronic data system application end user manual

Electronic data system application end user manual The MalariaCare Toolkit Tools for maintaining high-quality malaria case management services Electronic data system application end user manual Download all the MalariaCare tools from: www.malariacare.org/resources/toolkit.

More information

WI-FI GARAGE DOOR CONTROLLER WITH CAMERA USER MANUAL

WI-FI GARAGE DOOR CONTROLLER WITH CAMERA USER MANUAL WI-FI GARAGE DOOR CONTROLLER WITH CAMERA USER MANUAL Contents Introduction 4 Product Features 5 Garage Door Controller LED Indicators 6 What s Included 7 Wi-Fi Requirements 8 Mobile Device Requirements

More information

EC-11 Ethernet Converter

EC-11 Ethernet Converter EC-11 Ethernet Converter PSTN Contact ID to TCP Converter Installation and Operations Manual Version 8.H3.MID 1 Table of Contents About EC-11 Ethernet Converter... 3 Circuit Board Layout and Wiring Diagram...

More information

Contents. 1. Verify the package contents

Contents. 1. Verify the package contents Bullet VERSION 1.3 This installation guide provides basic instructions for installing the PLC-325PW/ PLC-335PW on your network and then configure Android, ios App and PC software to view the camera. For

More information

Downloaded from manuals search engine. Quick Start

Downloaded from   manuals search engine. Quick Start Quick Start Thank you for purchasing the Mobile WiFi. This Mobile WiFi brings you a high speed wireless network connection. This document will help you understand your Mobile WiFi so you can start using

More information

Finding information on your computer

Finding information on your computer Important Be sure to create recovery discs immediately after your computer is ready for use because there are no recovery discs provided with the computer. For instructions on how to create the recovery

More information

WRE6606. User s Guide. Quick Start Guide. Dual-Band Wireless AC1300 Access Point. Default Login Details. Version 1.00 (ABDU.0) Edition 1, 10/2016

WRE6606. User s Guide. Quick Start Guide. Dual-Band Wireless AC1300 Access Point. Default Login Details. Version 1.00 (ABDU.0) Edition 1, 10/2016 WRE6606 Dual-Band Wireless AC1300 Access Point Version 1.00 (ABDU.0) Edition 1, 10/2016 Quick Start Guide User s Guide Default Login Details Web Address http://zyxelsetup http://dhcp-assigned IP www.zyxel.comhttp://192.168.1.2

More information

Wireless Video/Audio Intercoms

Wireless Video/Audio Intercoms Wireless Video/Audio Intercoms User Set-Up Guide and Instructions BEC Integrated Solutions Williamsville, New York 716-689-0871 1 Table of Contents: B-WSP1.Page 3 B-WSP2 Page 8 B-WC2..Page 13 B-WI2 Page

More information

quick start guide portable wireless speaker Welcome PREMIER Instructions en français...9 Instrucciones en español...17

quick start guide portable wireless speaker Welcome PREMIER Instructions en français...9 Instrucciones en español...17 AWSBT10BK PREMIER portable wireless speaker quick start guide Welcome Congratulations on your purchase of this Acoustic Research Premier Series speaker, the ultimate in stereo-capable wireless sound. This

More information

DI GHz Wireless Router

DI GHz Wireless Router This product can be set up using any current web browser, i.e., Internet Explorer 6 or Netscape Navigator 6.2.3. DI-514 2.4GHz Wireless Router Before You Begin 1. If you purchased this router to share

More information

Congratulations on the purchase of your new Clover Mobile

Congratulations on the purchase of your new Clover Mobile Congratulations on the purchase of your new Clover Mobile Set Up the Hardware What s included Optional Accessories Clover Mobile Dock Clover Mobile Printer Clover Mobile Clover Clip Clover PIN Entry Aid

More information