Computer Networking. December 2004 CEN CN
|
|
- Madison Austin
- 6 years ago
- Views:
Transcription
1 Computer Networking CEN CN 1
2 Layer 2 - Bridge Frame Header Data Bridge Trailer Data Link Layer Physical Layer More complex than repeat, it requires hardware and software Bridges have diminished because of the widespread use of switch technology. Operate on frames, PDU= frames and based their decision on the destination address of the frame. CEN CN 2
3 Layer 2 - Bridge Node Node Server Node Bridge Node Node Server Node Filtering is when the bridge does not forward the frame to the other bridge ports. Forwarding is sending the frame out another port to the appropriate segment. Isolate traffic to local LAN segment to increase the overall performance of a network. CEN CN 3
4 Transparent Bridge The endpoint devices do not need to know that the bridges exist. Three key functions. Learning. Forwarding or filtering. Spanning-tree protocol. Mac address table MAC Address Associated Port CEN CN 4
5 Bridge Operations A frame is received. If the destination is a broadcast or multicast, forward on all ports. If the destination is a unicast and the address is not in the address table, forward on all ports. If the destination is a unicast and the address is in the address table, forward the frame out the associated port, unless the MAC address is associated with the incoming port. CEN CN 5
6 Transparent Bridge Summary Broadcast & multicast are forwarded by a bridge Layer 2 header & addresses Layer 3 protocol independent Different collision domain One broadcast domain Store-and-forward operation Latency (compare to a single-lan segment) CEN CN 6
7 Spanning Tree Protocol (STP) Network Redundant Links without STP Physically redundant paths exist. PcA B3 PcC. PcA B2 b1 PcC. Q: PcA sends a single unicast frame to PcC, but PcC is powered off and none of bridges has learned PcC s address. Frame to PcC will loop forever. CEN CN 7
8 Spanning Tree Protocol (STP) STP blocks some ports so that only one active path exists between any pair of LAN segment (collision domains) to dynamically create a bridge/switched network. Set the bridge port state, forward or block? Benefit Redundant Link in case of failure of one link Only one active link Loop avoided CEN CN 8
9 Switch Multi-port Bridge Selection Issues: Speed Media or user interface Need for trunking and interswitch links Workgroup segmentation (VLANs) Port density needs Product Category Desktop/Workgroup Level Cisco Catalyst 1900, 2900 XL series Wiring Closet/Backbone Level Cisco Catalyst 5000 series CEN CN 9
10 Switch - Method Store-and-forward. The switch fully receives all bits in the frame before forwarding the frame. This allows the switch to check the FCS before forwarding the frame. Cut-through. The switch performs the address table lookup as soon as the destination address field in the header is received. The first bit in the frame can be sent out the outbound port before the final bits in the incoming frame are received. Fragment-free. This performs like cut-through, but the switch waits for 64 bytes to be received before forwarding the first bytes of the outgoing frame. According to the Ethernet specifications, collisions should be detected during the first 64B of the frame. CEN CN 10
11 Traditional LAN vs. VLAN CEN CN 11
12 VLAN A group of ports or users in the same broadcast domain LAN switches and network management software provide a mechanism to create VLANs Remove Physical Boundary Group users by department, team, or application Routers provide communication between VLANs CEN CN 12
13 VLAN Frame tagged with VLAN ID Trunking CEN CN 13
14 Port-based VLAN Types of VLANs Example File Server VLAN1: Port 1,2,7,13 VLAN2: Port 3,4,8 VLAN3: Port 5,6, A B C D E F G H CEN CN 14
15 Mac-address Based VLAN Types of VLANs Example MAC address A: ABC B: DEF C: GHI 13 File Server VLAN1: ABC DEF Switch Hub A B C D E F CEN CN 15
Internetworking Concepts Overview. 2000, Cisco Systems, Inc. 2-1
Internetworking Concepts Overview 2000, Cisco Systems, Inc. 2-1 2000, Cisco Systems, Inc. www.cisco.com ICND v1.0a 2-2 Objectives On completion of this chapter, you will be able to perform the following
More information- Hubs vs. Switches vs. Routers -
1 Layered Communication - Hubs vs. Switches vs. Routers - Network communication models are generally organized into layers. The OSI model specifically consists of seven layers, with each layer representing
More informationCatalyst 1900 Series and Catalyst 2820 Series Enterprise Edition Software Configuration Guide
INDEX A allowed list, VLAN 2-28 to 2-29 ATM 2-5 firmware upgrade B-5 to B-7 LANE trunk connections 1-4 module 2-9, 2-13, 2-23 networks 2-5 trunk 2-4, 2-14 B bridge groups 3-15 bridge number 2-10 Bridge
More informationChapter 3 Part 2 Switching and Bridging. Networking CS 3470, Section 1
Chapter 3 Part 2 Switching and Bridging Networking CS 3470, Section 1 Refresher We can use switching technologies to interconnect links to form a large network What is a hub? What is a switch? What is
More informationChapter 6 Connecting Device
Computer Networks Al-Mustansiryah University Elec. Eng. Department College of Engineering Fourth Year Class Chapter 6 Connecting Device 6.1 Functions of network devices Separating (connecting) networks
More informationLOCAL AREA NETWORKS Q&A Topic 4: VLAN
A. Indicate whether the sentence or statement is true or false: 1. VLANs are more flexible in handling moves and additions of ports than routers 2. VLANs logically segment the physical LAN infrastructure
More informationSwitched Ethernet Virtual LANs
Switched Ethernet Virtual LANs Computer Networks Lecture 4 http://goo.gl/pze5o8 Switched Ethernet 2 LAN Switches Behave as bridges (operates in the logical tree topology) Switching is implemented by hardware
More informationConnecting to the Network
Connecting to the Network Networking for Home and Small Businesses Chapter 3 1 Objectives Explain the concept of networking and the benefits of networks. Explain the concept of communication protocols.
More informationLecture 9: Switched Ethernet Features: STP and VLANs
Lecture 9: Switched Ethernet Features: STP and VLANs Dr. Mohammed Hawa Electrical Engineering Department University of Jordan EE426: Communication Networks Ethernet Switch Features The following features
More informationTable of Contents 1 VLAN Configuration 1-1
Table of Contents 1 VLAN Configuration 1-1 Overview 1-1 Introduction to VLAN 1-1 VLAN Fundamentals 1-2 Types of VLAN 1-3 Introduction to Port-Based VLAN 1-3 Configuring a VLAN 1-4 Configuration Task List
More informationVLANs Level 3 Unit 9 Computer Networks
VLANs Some Requirements of LANs Need to split up broadcast domains to make good use of bandwidth People in different departments may need to be grouped together for access to servers Security: restrict
More informationHubs. twisted pair. hub. 5: DataLink Layer 5-1
Hubs Hubs are essentially physical-layer repeaters: bits coming from one link go out all other links at the same rate no frame buffering no CSMA/CD at : adapters detect collisions provides net management
More informationIntroducing Campus Networks
Cisco Enterprise Architecture Introducing Campus Networks 2003, Cisco Systems, Inc. All rights reserved. 2-1 2003, Cisco Systems, Inc. All rights reserved. BCMSN v2.0 2-2 Campus Data Center Combines switching
More informationComputer Networks Principles LAN - Ethernet
Computer Networks Principles LAN - Ethernet Prof. Andrzej Duda duda@imag.fr http://duda.imag.fr 1 Interconnection structure - layer 3 interconnection layer 3 router subnetwork 1 interconnection layer 2
More informationThe MAC Address Format
Directing data is what addressing is all about. At the Data Link layer, this is done by pointing PDUs to the destination MAC address for delivery of a frame within a LAN. The MAC address is the number
More informationAntonio Cianfrani. Virtual LAN (VLAN)
Antonio Cianfrani Virtual LAN (VLAN) Ethernet Ethernet standard (IEEE 802.3) for Local Area Network (LAN). CSMA/CD (Carrier Sense Multiple Access/Collision Detection) Carrier Sense: all devices have to
More informationUnderstanding Issues Related to Inter VLAN Bridging
Understanding Issues Related to Inter VLAN Bridging Document ID: 11072 Contents Introduction Prerequisites Requirements Components Used Conventions Spanning Tree Topology Concerns Recommended Use of Hierarchical
More informationVLANs. LAN Switching and Wireless Chapter 3. Version Cisco Systems, Inc. All rights reserved. Cisco Public 1
VLANs LAN Switching and Wireless Chapter 3 Version 4.0 2006 Cisco Systems, Inc. All rights reserved. Cisco Public 1 Objectives Explain the role of VLANs in a converged network. Explain the role of trunking
More informationChapter 5 Reading Organizer After completion of this chapter, you should be able to:
Chapter 5 Reading Organizer After completion of this chapter, you should be able to: Describe the operation of the Ethernet sublayers. Identify the major fields of the Ethernet frame. Describe the purpose
More informationChapter 3 Reading Organizer
Name Date Chapter 3 Reading Organizer After completion of this chapter, you should be able to: 3.1 Compare the types of switches used in an enterprise network. Explain how Spanning Tree Protocol prevents
More information3. What could you use if you wanted to reduce unnecessary broadcast, multicast, and flooded unicast packets?
Nguyen The Nhat - Take Exam Exam questions Time remaining: 00: 00: 51 1. Which command will give the user TECH privileged-mode access after authentication with the server? username name privilege level
More informationOverview. Overview. OTV Fundamentals. OTV Terms. This chapter provides an overview for Overlay Transport Virtualization (OTV) on Cisco NX-OS devices.
This chapter provides an overview for Overlay Transport Virtualization (OTV) on Cisco NX-OS devices., page 1 Sample Topologies, page 6 OTV is a MAC-in-IP method that extends Layer 2 connectivity across
More informationUpon completion of this chapter, you will be able to perform the following tasks: Identify what a VLAN is and how it operates. Configure a VLAN to
Upon completion of this chapter, you will be able to perform the following tasks: Identify what a VLAN is and how it operates. Configure a VLAN to improve network performance. Identify what role the switch
More informationGuide to Networking Essentials, 6 th Edition. Chapter 7: Network Hardware in Depth
Guide to Networking Essentials, 6 th Edition Chapter 7: Network Hardware in Depth Objectives Describe the advanced features and operation of network switches Describe routing table properties and discuss
More informationThe following steps should be used when configuring a VLAN on the EdgeXOS platform:
EdgeXOS VLANs VLAN Overview This document provides an overview of what a VLAN is and how it is configured on the EdgeXOS platform. Use the step-by-step guide below to configure a VLAN on the Edge appliance
More informationData Communications. Connecting Devices
Data Communications Connecting Devices Connecting Devices Networks do not normally operate in isolation. They are connected to one another or to the Internet. To connect LANs, or segments of LANs, we use
More informationCCNA Layer 2 switching. Revision no.: PPT/2K605/03
CCNA 640-801 Layer 2 switching Revision no.: PPT/2K605/03 What is Switching? It breaks the Collision Domain It takes the packet and forwards to destined port without any modification. Network still remains
More informationA. ARPANET was an early packet switched network initially connecting 4 sites (Stanford, UC Santa Barbara, UCLA, and U of Utah).
Volume: 245 Questions Question No: 1 Which of the following statements best describes ARPANET? A. ARPANET was an early packet switched network initially connecting 4 sites (Stanford, UC Santa Barbara,
More informationImi :... Data:... Nazwisko:... Stron:...
Imi :.................................................... Data:....................... Nazwisko:............................................... Stron:...................... 1. Which of the following protocols
More informationPrivate and Public addresses. Real IPs. Lecture (09) Internetwork Layer (3) Agenda. By: Dr. Ahmed ElShafee
Agenda Lecture (09) Internetwork Layer (3) Private and public addresses Network Address Translation Virtual Private Network (VPN) Virtual LANs By: Dr. Ahmed ElShafee ١ ٢ Private and public addresses Private
More informationConfiguring VLANs. Understanding VLANs CHAPTER
CHAPTER 11 This chapter describes how to configure normal-range VLANs (VLAN IDs 1 to 1005) and extended-range VLANs (VLAN IDs 1006 to 4094) on the Cisco ME 3400 Ethernet Access switch. It includes information
More informationTransparent Bridging and VLAN
Transparent Bridging and VLAN Plug and Play Networking (C) Herbert Haas 2005/03/11 Algorhyme I think that I shall never see a graph more lovely than a tree a graph whose crucial property is loop-free connectivity.
More informationImage courtesy Cisco Systems, Inc. Illustration of a Cisco Catalyst switch
by Jeff Tyson If you have read other HowStuffWorks articles on networking or the Internet, then you know that a typical network consists of nodes (computers), a connecting medium (wired or wireless) and
More informationCCNA Cisco Certified Network Associate CCNA (v3.0)
200-125 - CCNA Cisco Certified Network Associate CCNA (v3.0) 1.What is one benefit of PVST+? A. PVST+ supports Layer 3 load balancing without loops. B. PVST+ reduces the CPU cycles for all the switches
More informationAdditional Slides (Basics) Intermediate Systems
Automation Systems Discrete Event Control Systems and Networked Automation Systems Additional Slides (Basics) Intermediate Systems Outline Building Larger (and more Reliable) Networks: Intermediate Systems
More informationChapter 15 Local Area Network Overview
Chapter 15 Local Area Network Overview LAN Topologies Bus and Tree Bus: stations attach through tap to bus full duplex allows transmission and reception transmission propagates throughout medium heard
More informationRouting Between VLANs Overview
Routing Between VLANs Overview This chapter provides an overview of VLANs. It describes the encapsulation protocols used for routing between VLANs and provides some basic information about designing VLANs.
More informationSwitching and Forwarding Reading: Chapter 3 1/30/14 1
Switching and Forwarding Reading: Chapter 3 1/30/14 1 Switching and Forwarding Next Problem: Enable communication between hosts that are not directly connected Fundamental Problem of the Internet or any
More informationVLAN Configuration. Understanding VLANs CHAPTER
CHAPTER 11 This chapter describes how to configure normal-range VLANs (VLAN IDs 1 to 1005) and extended-range VLANs (VLAN IDs 1006 to 4094) on the CGR 2010 ESM. It includes information about VLAN membership
More informationConfiguring IEEE 802.1Q Tunneling and Layer 2 Protocol Tunneling
CHAPTER 14 Configuring IEEE 802.1Q Tunneling and Layer 2 Protocol Tunneling With Release 12.1(13)E and later, the Catalyst 6500 series switches support IEEE 802.1Q tunneling and Layer 2 protocol tunneling.
More informationConfiguring MPLS and EoMPLS
37 CHAPTER This chapter describes how to configure multiprotocol label switching (MPLS) and Ethernet over MPLS (EoMPLS) on the Catalyst 3750 Metro switch. MPLS is a packet-switching technology that integrates
More informationConfiguring VLANs CHAPTER
CHAPTER 8 This chapter describes how to configure your access point to operate with the VLANs set up on your wired LAN. These sections describe how to configure your access point to support VLANs: Understanding
More informationMore on LANS. LAN Wiring, Interface
More on LANS Chapters 10-11 LAN Wiring, Interface Mostly covered this material already NIC = Network Interface Card Separate processor, buffers incoming/outgoing data CPU might not be able to keep up network
More informationDD2490 p Layer 2 networking. Olof Hagsand KTH CSC
DD2490 p4 2010 Layer 2 networking Olof Hagsand KTH CSC 1 Literature Radia Pearlman Interconnections - Bridges, Routers, Switches and Internetworking Protocols, Addison-Wesley. Section 3: Transparent bridges
More informationChapter 16: Switched Ethernet in Automation. Wenbo Qiao
Chapter 16: Switched Ethernet in Automation Wenbo Qiao Ethernet Basics What is Ethernet? Why Ethernet? ( not FieldBus?) Flexibility, Scalability and Performance Key Strength: many protocols running simultaneously
More informationConfiguring VLANs. Understanding VLANs CHAPTER
CHAPTER 14 This chapter describes how to configure normal-range VLANs (VLAN IDs 1 to 1005) and extended-range VLANs (VLAN IDs 1006 to 4094). It includes information about VLAN modes and the VLAN Membership
More informationConfiguring your VLAN. Presented by Gregory Laffoon
Configuring your VLAN Presented by Gregory Laffoon 1 Overview of Networking Terms Networking Terms Overview OSI Model Defines a networking framework for implementing protocols in seven layers Control is
More informationECE 435 Network Engineering Lecture 21
ECE 435 Network Engineering Lecture 21 Vince Weaver http://web.eece.maine.edu/~vweaver vincent.weaver@maine.edu 27 November 2018 Announcements HW#9 was posted Project Status One e-mail per group One-line
More informationChapter 2. Switch Concepts and Configuration. Part I
Chapter 2 Switch Concepts and Configuration Part I CCNA3-1 Chapter 2-1 Note for Instructors These presentations are the result of a collaboration among the instructors at St. Clair College in Windsor,
More informationLayer 2 functionality bridging and switching
Layer 2 functionality bridging and switching BSAD 141 Dave Novak Sources: Network+ Guide to Networks, Dean 2013 Overview Layer 2 functionality Error detection Bridges Broadcast and collision domains How
More informationChapter 4 Configuring Switching
Chapter 4 Configuring Switching Using the Switching Tab The navigation tabs on the top of the home page include a Switching tab that lets you manage your GS108T Gigabit Smart Switch using features under
More informationConfiguring VLANs. Understanding VLANs CHAPTER
CHAPTER 9 This chapter describes how to configure normal-range VLANs (VLAN IDs 1 to 1005) and extended-range VLANs (VLAN IDs 1006 to 4094). It includes information about VLAN membership modes, VLAN configuration
More informationCSCI Computer Networks
CSCI-1680 - Computer Networks Link Layer III: LAN & Switching Chen Avin Based partly on lecture notes by David Mazières, Phil Levis, John Jannotti, Peterson & Davie, Rodrigo Fonseca Today: Link Layer (cont.)
More informationData Link Layer. Our goals: understand principles behind data link layer services: instantiation and implementation of various link layer technologies
Data Link Layer Our goals: understand principles behind data link layer services: link layer addressing instantiation and implementation of various link layer technologies 1 Outline Introduction and services
More informationYildiz Technical University Computer Engineering Department BLM 6196 Computer Networks And Communication Protocols.
Yildiz Technical University Computer Engineering Department BLM 6196 Computer Networks And Communication Protocols Hubs and Switches Prepared by: Naseer Ahmad SEDDIQI Email Address: seddiqinaseer@gmail.com
More informationConfiguring VLANs. Understanding VLANs CHAPTER
7 CHAPTER This chapter describes how to configure normal-range VLANs (VLAN IDs 1 to 1005) and extended-range VLANs (VLAN IDs 1006 to 4094) on the Cisco MWR 2941 router. It includes information about VLAN
More informationPrinciples behind data link layer services
Data link layer Goals: Principles behind data link layer services Error detection, correction Sharing a broadcast channel: Multiple access Link layer addressing Reliable data transfer, flow control: Done!
More informationPort ACLs (PACLs) Prerequisites for PACls CHAPTER
71 CHAPTER Prerequisites for PACls, page 71-1 Restrictions for PACLs, page 71-2 Information About PACLs, page 71-2 How to Configure PACLs, page 71-7 Note For complete syntax and usage information for the
More informationConfiguring VLANs. Understanding VLANs CHAPTER
CHAPTER 10 This chapter describes how to configure normal-range VLANs (VLAN IDs 1 to 1005) and extended-range VLANs (VLAN IDs 1006 to 4094) on the switch. It includes information about VLAN membership
More informationSome portions courtesy Srini Seshan or David Wetherall
CSE 123 Computer Networks Fall 2009 Lecture 6: Data-Link III: Hubs, Bridges and Switches Some portions courtesy Srini Seshan or David Wetherall Misc Homework solutions have been posted I ll post a sample
More informationGuide to Networking Essentials, 6 th Edition. Chapter 7: Network Hardware in Depth
Guide to Networking Essentials, 6 th Edition Chapter 7: Network Hardware in Depth Objectives Describe the advanced features and operation of network switches Describe routing table properties and discuss
More informationConfiguring Virtual Private LAN Services
Virtual Private LAN Services (VPLS) enables enterprises to link together their Ethernet-based LANs from multiple sites via the infrastructure provided by their service provider. This module explains VPLS
More informationHigher scalability to address more Layer 2 segments: up to 16 million VXLAN segments.
This chapter tells how to configure Virtual extensible LAN (VXLAN) interfaces. VXLANs act as Layer 2 virtual networks over Layer 3 physical networks to stretch Layer 2 networks. About VXLAN Encapsulation
More informationConfiguring IEEE 802.1Q and Layer 2 Protocol Tunneling
CHAPTER 8 Configuring IEEE 802.1Q and Layer 2 Protocol Tunneling Virtual private networks (VPNs) provide enterprise-scale connectivity on a shared infrastructure, often Ethernet-based, with the same security,
More informationPrinciples behind data link layer services:
Data link layer Goals: Principles behind data link layer services: Error detection, correction Sharing a broadcast channel: Multiple access Link layer addressing Reliable data transfer, flow control Example
More informationPrinciples behind data link layer services:
Data link layer Goals: Principles behind data link layer services: Error detection, correction Sharing a broadcast channel: Multiple access Link layer addressing Reliable data transfer, flow control Example
More informationConfiguring BPDU tunneling
Contents Configuring BPDU tunneling 1 Introduction to BPDU tunneling 1 Background 1 BPDU Tunneling implementation 2 Configuring BPDU tunneling 3 Configuration prerequisites 3 Enabling BPDU tunneling for
More informationRouting Between VLANs Overview
Routing Between VLANs Overview This chapter provides an overview of VLANs. It describes the encapsulation protocols used for routing between VLANs and provides some basic information about designing VLANs.
More informationConfiguring VLANs CHAPTER
CHAPTER 13 This chapter describes how to configure your access point/bridge to operate with the VLANs set up on your wired LAN. These sections describe how to configure your access point/bridge to support
More informationConfiguring IEEE 802.1Q Tunneling and Layer 2 Protocol Tunneling
9 CHAPTER Configuring IEEE 802.1Q Tunneling and Layer 2 Protocol Tunneling Virtual private networks (VPNs) provide enterprise-scale connectivity on a shared infrastructure, often Ethernet-based, with the
More informationCS343: Data Communication LAN Overview
CS343: Data Communication LAN Overview by Dr. Manas Khatua Assistant Professor Dept. of CSE IIT Guwahati E-mail: manaskhatua@iitg.ac.in Communication Network Topology Topology refers to the way in which
More informationFor information about configuring these settings from Cluster Management Suite (CMS), refer to the online help.
Configuring VLANs This chapter provides information about configuring virtual LANs (VLANs). It includes command-line interface (CLI) procedures for using commands that have been specifically created or
More informationNetworking for Data Acquisition Systems. Fabrice Le Goff - 14/02/ ISOTDAQ
Networking for Data Acquisition Systems Fabrice Le Goff - 14/02/2018 - ISOTDAQ Outline Generalities The OSI Model Ethernet and Local Area Networks IP and Routing TCP, UDP and Transport Efficiency Networking
More informationEnterprise. Nexus 1000V. L2/L3 Fabric WAN/PE. Customer VRF. MPLS Backbone. Service Provider Data Center-1 Customer VRF WAN/PE OTV OTV.
2 CHAPTER Cisco's Disaster Recovery as a Service (DRaaS) architecture supports virtual data centers that consist of a collection of geographically-dispersed data center locations. Since data centers are
More informationConfiguring IGMP Snooping and MVR
CHAPTER 21 This chapter describes how to configure Internet Group Management Protocol (IGMP) snooping on the Cisco ME 3400 Ethernet Access switch, including an application of local IGMP snooping, Multicast
More informationConfiguring Interfaces
CHAPTER 9 This chapter defines the types of interfaces on the Cisco ME 3400 Ethernet Access switch and describes how to configure them. Understanding Interface Types, page 9-1 Using Interface Configuration
More informationInternetwork Expert s CCNP Bootcamp. Hierarchical Campus Network Design Overview
Internetwork Expert s CCNP Bootcamp Hierarchical Campus Network Design Overview http:// Hierarchical Campus Network Design Overview Per Cisco, a three layer hierarchical model to design a modular topology
More informationChapter 5: Ethernet. Introduction to Networks - R&S 6.0. Cisco Networking Academy. Mind Wide Open
Chapter 5: Ethernet Introduction to Networks - R&S 6.0 Cisco Networking Academy Mind Wide Open Chapter 5 - Sections 5.1 Ethernet Protocol Describe the Ethernet MAC address and frame fields 5.2 LAN Switches
More informationSpanning-Tree Protocol
Spanning-Tree Protocol Malin Bornhager Halmstad University Session Number 2002, Svenska-CNAP Halmstad University 1 Objectives Redundancy in a converged network Spanning-Tree Protocol (STP) STP Operation
More informationCisco Systems, Inc. Norman Finn. July 9, /12. Class of Service in Class of Service in Norman Finn Cisco Systems
Class of Service in 802.1 Norman Finn Cisco Systems, Inc. July 9, 1996 1/12 CoS Bridging Example sw2 16 Mb T-R 100 Mb Ether sw3 sw1 10 Mb Ether FDDI X Y 100 Mb and 10 Mb Ethernet prevent passing access
More informationEthernet. Network Fundamentals Chapter Cisco Systems, Inc. All rights reserved. Cisco Public 1
Ethernet Network Fundamentals Chapter 9 1 Objectives Identify the basic characteristics of network media used in Ethernet. Describe the physical and data link features of Ethernet. Describe the function
More informationWhat LinkSec Should Know About Bridges Norman Finn
What LinkSec Should Know About Bridges Norman Finn What LinkSec Should Know About Bridges Rev. 2 Norman Finn, Cisco Systems IEEE 802 LinkSec SG 1/20 What Do Bridges Do? (1) A network of bridges emulates
More informationMore on Link Layer. Recap of Last Class. Interconnecting Nodes in LAN (Local-Area Network) Interconnecting with Hubs. Computer Networks 9/21/2009
More on Link Layer Kai Shen Recap of Last Class Ethernet dominant link layer technology for local-area l networks Ethernet frame structure Ethernet multiple access control CSMA/CD, exponential back-off
More informationConfiguring Private VLANs
36 CHAPTER This chapter describes private VLANs (PVLANs) on Catalyst 4500 series switches. It also provides restrictions, procedures, and configuration examples. This chapter includes the following major
More information3.5 CONNECTING DEVICES
3.5 CONNECTING DEVICES LANs or WANs do not normally operate in isolation. They are connected to one another or to the Internet. To connect LANs and WANs together we use connecting devices. Connecting devices
More informationConfiguring Interfaces
CHAPTER 9 This chapter defines the types of interfaces on the Cisco ME 3400 Ethernet Access switch and describes how to configure them. The chapter consists of these sections: Understanding Interface Types,
More informationSections Describing Standard Software Features
30 CHAPTER This chapter describes how to configure quality of service (QoS) by using automatic-qos (auto-qos) commands or by using standard QoS commands. With QoS, you can give preferential treatment to
More informationTraffic/Security Filters
10 Traffic/Security Filters Contents Overview..................................................... 10-2 Introduction.................................................. 10-2 Filter Limits...............................................
More informationL2 Bridging Across an L3 Network Configuration Example
L2 Bridging Across an L3 Network Configuration Example Document ID: 116266 Contributed by Atri Basu, Jay Young Taylor, and Mani Ganesan, Cisco TAC Engineers. Jul 09, 2013 Contents Introduction Prerequisites
More informationCisco Introducing Cisco Data Center Networking - DCICN. Download Full version :
Cisco 640-911 Introducing Cisco Data Center Networking - DCICN Download Full version : http://killexams.com/pass4sure/exam-detail/640-911 There is a large amount of traffic inside a network segment with
More informationSeite von 7 05.0.200 Close Window Assessment System Exam Viewer - CCNA Practice Certification Exam # - (Version 4.0) Below you will find the assessment items as presented on the exam as well as the scoring
More informationQ&As Implementing Cisco IP Switched Networks (SWITCH v2.0)
CertBus.com 300-115 Q&As Implementing Cisco IP Switched Networks (SWITCH v2.0) Pass Cisco 300-115 Exam with 100% Guarantee Free Download Real Questions & Answers PDF and VCE file from: 100% Passing Guarantee
More information: Building Cisco Multilayer Switched Networks
Exam : Cisco 642-812 Title : Building Cisco Multilayer Switched Networks Version : Demo Cheat-Test,help you pass any IT exam! Q: 1 Which three statements about the Multiple Spanning Tree (MST) protocol
More informationVirtual University of Pakistan. Describe the Hidden Node and Exposed Node problems in Standard? VUSR. [Larry L. Peterson]
www..net Solution Assignment No. 2 Question No. 1 Describe the Hidden Node and Exposed Node problems in 802.11 Standard? Hidden Node Problem: Consider the figure below. [Larry L. Peterson] B can exchange
More informationTop-Down Network Design
Top-Down Network Design Chapter Seven Selecting Switching and Routing Protocols Original slides by Cisco Press & Priscilla Oppenheimer Selection Criteria for Switching and Routing Protocols Network traffic
More informationConfiguring EtherChannels and Link-State Tracking
CHAPTER 37 Configuring EtherChannels and Link-State Tracking This chapter describes how to configure EtherChannels on Layer 2 and Layer 3 ports on the switch. EtherChannel provides fault-tolerant high-speed
More informationIEEE 802.1ad Support on Provider Bridges
IEEE 802.1ad Support on Provider Bridges First Published: April 19, 2010 Last Updated: May 26, 2011 Service provider bridges (also called provider bridges) allow switches in a service provider network
More informationSwitching & ARP Week 3
Switching & ARP Week 3 Module : Computer Networks Lecturer: Lucy White lbwhite@wit.ie Office : 324 Many Slides courtesy of Tony Chen 1 Ethernet Using Switches In the last few years, switches have quickly
More informationConfiguring VLANs. Understanding VLANs
This document describes how to configure your Cisco wireless mobile interface card (WMIC) to operate with the VLANs set up on your wired LAN. These sections describe how to configure your WMIC to support
More informationCCENT Study Guide. Chapter 2 Ethernet Networking and Data Encapsulation
CCENT Study Guide Chapter 2 Ethernet Networking and Data Encapsulation Chapter 2 Objectives The CCENT Topics Covered in this chapter include: Network Fundamentals 1.6 Select the appropriate cabling type
More information