JDSU Packet Transport Network (PTN) Test Solutions and Examples. Communications Test and Measurement Solutions

Transcription

1 JDSU Packet Transport Network (PTN) Test Solutions and Examples Communications Test and Measurement Solutions

2 Table of Contents JDSU PTN Test Solutions and Examples... 3 ONT Optical Network Tester... 4 T-BERD 8000 Integrated Field Application Tester... 6 T-BERD 6000A and 8000 Multi-Service Application Module (MSAM)... 7 T-BERD 5800 Handheld Network Tester... 8 HST-3000 Ethernet Handheld Tester... 9 SmartClass Ethernet Fiber Inspection, Cleaning and Test Solutions Power Measurement and Fiber Identification Solutions OTDR and Optical Power Measurement Solutions Test Example 1: End-to-End MPLS-TP Flow and OAM Verification Test Example 2: MPLS-TP Flow Real-Time Network Monitoring Test Example 3: Ensure Accurate Time Synchronization Verification for 1588v2 Networks Test Example 4: PTN One-Way Latency Test Test Example 5: Synchronous Ethernet Clock Synchronization Test

3 JDSU PTN Test Solutions and Examples With full-service networks being IP-based, three major domestic carriers have put much energy into developing their own mobile backhaul technology in the past three years. As PTN technology possesses many inherent advantages, China Mobile has been widely using it as its first choice for mobile backhaul; China Telecom is also looking at the mobile backhaul technology for its FDD network, and testing focused on PTN has proven remarkable. China Unicom is following China Mobile and China Telecom, and has organized a large number of PTN tests. With the PTN network being gradually applied to access transmission networks, test programs are currently quite limited and there are no effective solutions. JDSU offers end-to-end PTN test solutions that cover the entire PTN application life cycle and various aspects from deployment to post-launch maintenance. It enhances the operator s confidence in network deployment, new service provisioning, network post-launch maintenance, and fault location. At the same time, it requires minimal hardware resources, is easy to use, and can save the user significant costs while handling large-scale applications. (5). T-BERD 5800 (7). HST-3000 PTN network topology and JDSU test tools 3

4 ONT Optical Network Tester The industry s most advanced and complete solutions for 1.5 Mbps to 112 G which can cover error, warning, switching, delay, overhead, pointer, clock synchronization, optical power, frequency offset, wander, and jitter, and can be applied to a variety of applications such as development, production, installation, commissioning, and maintenance. ONT-503/506 ModuleE+Jitter-E PTN Features The precision 1310/1550 nm jitter and wander function is the industry s only solution that meets Annexes VII and VIII of ITU-T O.172 and that can be calibrated, received, or sent with Golden TX. Detailed charting ensures the precision applied by each speed. Provides ±15 mui jitter measurement accuracy. Supports jitter and wander testing for 1/10.3 GE Sync-E, OTU1e, and OTU2e, and provides G.8262 testing templates. Includes CC64 khz, 1.5/2/6.3/10 MHz, E1/DS1, and 1 pps signal wander characteristics (TDEV, MTIE), wander tolerance, a wander transmission test function, the industry s only wander generation feature with noise modulation, and a corresponding G.8261 test template to satisfy the needs of various clock tests for PTN wireless backhaul. Includes a round-trip-delay (RTD) testing function. The industry s leading switching test function supports event triggering on multiple ODU and customer levels. Includes optional parallel and multi-trigger sources. Provides the industry s leading 64 VC-4, 192 VC-3, and STM16/OC-48 full-rate multi-channel test function, and supports OTU1 and OTU2 for each ODU particle mapping SDH/SONET load multi-channel testing. OTN scheduling functions include ODU0/ODU1 to OTU2 single-level or multilevel scheduling, support for ODUFlex, client signal mapping, and multichannel OTN. Fully supports the latest G.709/2009 standards. Fully supports two online test modes: transparent pass-through and enhanced penetration. Includes SONET/SDH and OTN online monitoring and on-line warning/error insertion, cost overrides. 4

5 Ordering Information ONT-506/503 Optical Network Tester Order Number ONT-506 Optical Network Tester 6 slot host box 3062/01 ONT-503 Optical Network Tester 3 slot host box 3075/01 Module-E 10G/2.5G XFP/SFP slot 10G/2.5G test module 3061/92.05 Module-E 10G XFP slot 3061/92.10 Jitter Module 10G-E 1310/1550 nm dual-wavelength 3061/90.76 Jitter Module 10G-E 1550 nm 10G 3061/90.75 Jitter 10.3G-E 10.3G 3061/90.70 Jitter 10.7G-E 10.7G 3061/90.78 Jitter Module 2.5G-D 1310/1550 nm dual-wavelength 3061/90.67 Jitter 2.5G-D 1550 nm 2.5G test module 3061/90.66 Jitter 2.7G-D 2.7G 3061/90.68 Jitter 1.25G-D 1.25G 3061/90.69 Software options Order Number 10GigE LAN 10G LAN test software 3061/ G Ethernet 1G Ethernet test software 3061/93.43 Lower Rates SDH/SONET low speed SDH/SONET test software 3061/93.34 SDH/SONET Single Channel 3061/93.36 OTN 2.7G 2.7G OTN test software 3061/93.49 OTN 10.7G 10.7G OTN test software 3061/93.57 Wander 10/11G 10G speed wander software 3061/93.95 Wander 10/11G Expert 3061/93.97 Wander 2.5/2.7G (software) 2.5G/2.7G wander test software 3061/93.92 Wander2.5/2.7G Expert 3061/93.89 Wander DS1/E1+BITS E1/T1 clock test 3061/93.96 Wander BITS Expert (hardware option) 3061/90.74 ESMC G.8264 SSM test 3061/

6 T-BERD 8000 Integrated Field Application Tester The industry s most advanced, portable, versatile, and integrated test platform covers error, warning, switching, delay, overhead, pointer, clock synchronization, optical power, frequency offset, wander and jitter, and can be applied to a variety of applications such as development, production, installation, commissioning, and maintenance. T-BERD 8000 Scalable Multitest Platform PTN Features High precision 1310/1550 nm jitter and wander features, fully compliant with the MTS-8000 Transport Module ITU-T O.172 Annexes VII and VIII. Includes functions for E1/DS1 signal jitter, wander characteristics (TDEV and MTIE), wander tolerance, wander transmission testing, and a wander-generation feature modulated with corresponding noise to meet the need for clock testing for PTN wireless backhaul. Advanced APS switching time test and a round-trip-delay (RTD) test feature. Provides the industry s most complete 10 Mbps-10 GE Layer 1-4 Ethernet testing with RFC 2544, VLAN, Q-in-Q, VPLS, MPLS, multi-stream, and full support for the ITU-T Y.1564 standard. Please contact your JDSU representative for ordering information. 6

7 T-BERD 6000A and 8000 Multi-Service Application Module (MSAM) T-BERD 6000A Compact Network Test Platform Key Benefits Maximizes ROI with a modular, field-upgradeable tester that seamlessly expands into future technologies and interfaces. Provides an industry-leading, multi-port 10 G modular platform for network field installation and advanced troubleshooting. Guarantees end-customer satisfaction with deep application layer testing for data (TrueSpeed per RFC 6349), voice (VoIP), and video (IPTV). Promotes an efficient service and network management life cycle with integrated installation tools and advanced troubleshooting analysis in a single test instrument. Reduces installation and troubleshooting times with automated J-Complete test tools that follow best practices and provide repeatable methods and procedures with easy-to-understand results. Extends the leading portfolio of T-BERD/MTS portable test solutions. The T-BERD product suite was created by experts to simplify network deployment and is trusted by leading service providers around the world. Applications Tests and troubleshoots converged Ethernet/IP backhaul for 10 Mbps to 10 G interfaces and captures and analyzes packets. Tests Layers 1-3 Ethernet/IP SLAs with an automated, enhanced RFC 2544/ SAMComplete per ITU-T Y Tests TDM/PDH to SONET/SDH at OC-3/STM-1 to OC-192/STM-64, including service-disruption measurements and path-overhead (POH) capture with triggers. Enables installation and maintenance of OTN networks up to 11.1 G and includes an interface with ODU-0 support for Ethernet client interfaces. Validates network synchronization for quality of experience on mobile applications. Emulates a 1588v2 master clock/slave recovery to ensure proper point-to-point (PTP) message propagation and to verify packet-delay variation (PDV). Verifies accurate SyncE frequency synchronization and Ethernet synchronization message channel (ESMC) message propagation. Ready for packet transport networks using MPLS-TP. Supports J-Complete, an exclusive suite of automated test tools from JDSU. Supports SFP and XFP pluggable optics including 50 GHz C-band tunable XFPs Please contact your JDSU representative for ordering information. 7

8 T-BERD 5800 Handheld Network Tester T-BERD 5800 Handheld Network Tester Key Benefits All-in-one handheld tool designed to reduce the complexity of multi-technology testing. Optimized for field ease-of-use while addressing emerging network technologies. Guarantees maximum efficiency and success in the evolution of carrier Ethernet and mobile backhaul networks. Ensures service life cycle management, integrating both installation and troubleshooting capabilities in one instrument. Automates services verification with support of the J-Complete suite of test tools. The T-BERD product suite was created by experts to simplify network deployment and is trusted by leading service providers around the world. Applications Six T-BERD 5800 configurations: Single- and dual-port Ethernet versions With or without TDM/PDH interfaces Fully loaded TDM/PDH to 10 GE, SONET, and SDH Layer 1-3 Ethernet/IP SLA verification with Class of Service testing that includes automated, enhanced RFC 2544 tests. Support for emerging Ethernet synchronization testing including 1588v2 and SyncE verification. BER testing up to OC192/STM-64, service disruption, and circuit monitoring on TDM/PDH/SONET/SDH interfaces. Supports PTN evolution with MPLS-TP technology. Supports the J-Complete automated suite of test applications. Please contact your JDSU representative for ordering information. 8

9 HST-3000 Ethernet Handheld Tester The industry s highest-performance, modular, and portable tester, with full support for multiple-access and metro-interconnect technology (including xdsl, copper, T1/E1, fiber, and Ethernet), can meet the needs of applications such as PTN access layer opening, maintenance, and optimization. HST-3000 Ethernet Module PTN Features Achieves full-speed port coverage from 10 Mbps to 1 GE for Ethernet network testing on a single test platform, and fully meets the needs of future LTE and IP networks. Meets the needs of Ethernet access-layer test applications in video and mobile backhaul. Complete 10 Mbps to 1 GE Layers 1-4 Ethernet support for RFC 2544, VLAN, Q-in-Q, VPLS, MPLS, and multi-stream. Ordering Information HST-3000 Portable PTN Business Tester HST3000 Non-Copper mainframe HST-3000 host Ethernet SIM for HST-3000 Ethernet test module Optical Ethernet option for HST-3000 Adv.IP Suite - PING and Through Mode support PING Advanced IP Directory Multiple Streams option for HST HST-3000 Soft Carrying Case Order Number HST3000-NG2 HST3000-ETH HST3000-OPTETH HST3000S-IP HST3000-MSTR CC

10 SmartClass Ethernet The SmartClass Ethernet product is an easy to use, cost-effective testing solution for basic physical layer cable testing, Layers 2/3 traffic generation, and full RFC 2544 testing. The rugged, battery operated, application-specific test tool lets field technicians turn-up Ethernet and IP services by running an RFC 2544 test or by following a set of methods and procedures. The SmartClass product comes in two major configurations, one a loopback-only device and the other featuring full traffic generation. SmartClass Ethernet Applications Quickly verify basic Ethernet backhaul performance on 10/100/1 GE with an automated RFC-2544 test. Verify Class of Services with up to eight independent traffic streams. Supports testing in MPLS/VPLS networks. Cost-effective loop device for end-to-end Layer 2/ 3 tests. Please contact your JDSU representative for ordering information. Fiber Inspection, Cleaning and Test Solutions As fiber penetrates further into next-generation networks, proactively inspecting and cleaning each connection point is no longer optional, but critical. Optimized physical performance of fiber connections is imperative to deliver future-proof and reliable PTN and LTE networks. Today s fiber technician needs tools that provide a seamless workflow for inspecting, cleaning, testing, and troubleshooting a fiber link that also drives behavior, best practices, and field efficiency. JDSU offers essential fiber-handling tools in fast, portable, and easy-to-use systems for any fiber technician. The P5000i Digital Analysis Microscope with FiberChek- PRO makes it fast and easy to certify that every connection in your network is optimized and compliant to IEC Standard pass/fail thresholds. HP3 Series Fiber Inspection and Test System with Compact Video Display and P500i Digital Analysis Microscope Ordering Information Product Description Fiber Essentials Tool Kit: Dual-mag (200/400X) FBP probe microscope and tips, FIT-HP2-60-P4 inspection and test system with 400X PCM, FFL-050 visual fault locator, cleaning tools, utility carrier, carrying case. Inspection Kit: Dual mag (200/400X)FBP probe microscope and tips, HD2 Display with 200x PCM and adaptors, case Utility Carrier System for FBP-SE05 Digital PASS/FAIL Analysis kit: P5000i, FiberChekPRO Software, tips and Case Digital PASS/FAIL Analysis & Test kit: P5000i, MP-60 w/ FiberChekPRO, tips, adaptors and Case Visual fault locator (compact) Visual fault locator (ruggedized) with 1.25 mm adapter Fiber Field Cleaning Kit Order Number FIT-S205-PRO FBP-SE05 FBPP-UC2 FBP-SD101 FBP-SD103 FFL-050 FFL-100 FCR-CLN-01 HP3-60 Kit with P5000i Digital Analysis Microscope and Visual Fault Locator 10

11 Power Measurement and Fiber Identification Solutions To deliver high-performance, best-in-class PTN or LTE networks, it is critical that fiber systems are correctly installed and tested. This ensures that the physical layer meets the minimum optical performance specification requirements to deliver reliable services. JDSU offers a wide array of solutions from fiber identifiers to insertion-loss and power-measurement tools. These tools are ideal for installation and maintenance applications for standard multimode and single-mode fibers and CWDM/DWDM systems. Ordering Information Product Description OMK-35P Singlemode SmartPocket Test is a dual-wavelength optical test kit with a single-port laser source and a power meter with a UPP interface for power level and loss test measurement in access, metro and core networks. Order Number 2127/02 FI-60 Live Fiber Identifier (left), OLS-35 SmartPocket Optical Light Source (center), SmartClass OCC-55 Optical CWDM Channel Checker (right) OLS /1550 nm Singlemode Light Source 2303/11 OCC-55 Optical Channel Checker for CWDM wavelengths. 2277/40 OCC-56 Optical Channel Checker for DWDM wavelengths 2277/41 Live Fiber Identifier- integrated OPM adaptors, software and case. FI-60 OTDR and Optical Power Measurement Solutions Fiber is the lifeline to your customers. The physical integrity of the fiber is critical for optimum service delivery. It is imperative to properly characterize the performance of the physical layer to ensure reliability. The MTS-2000 Handheld Modular Test Set solution addresses the complexity of fiber testing and drives maximum efficiency for technicians to perform all the tests required to ensure optimized performance and high-quality fiber networks. The MTS-2000 handles the widest range of test applications including OTDR, FiberComplete automatic IL/ORL, CWDM analyzer, and connector inspection with IEC pass/fail analysis. This solution makes even the most novice fiber tech an instant fiber expert. Ordering Information Product Description Order Number MTS-2000 Handheld Modular Test Set MTS-2000 Handheld Modular Test Set EM2000T OTDR module: Last Mile range 1310/1550nm E4126LM OTDR module: Metro-Access range 1310/1550nm E4126MA FiberComplete Module: Metro-Access OTDR, IL, ORL 1310/1550nm E4126FCOMP-MA Light source option for OTDR Module (through OTDR port) E41OTDRLS Power Meter option for OTDR Module (through OTDR port) E4OTDRPM Optical Spectrum Analyzer for CWDM COSA /01 Digital PASS/FAIL Analysis & Test kit: P5000i with FiberChekPRO, 7x tips and Case FBP-MTS

12 Test Example 1: End-to-End MPLS-TP Flow and OAM Verification By connecting the test instrument to the proximal and distal converter or router port, you can use the T-BERD 6000A/8000 MSAM or T-BERD 5800 to generate and analyze end-to-end MPLS-TP flows. In this example, each test instrument is configured with terminal mode to measure the flow of simulation customer data sent along each direction. Subsequently, analysis can be done on each test instrument for detected test flow, MPLS-TP Provider A MPLS-TP Provider B Customer service (such as Ethernet) Ca1a MPLS-TP FW Ca1a pa1a Cb1b MPLS-TP LSP Ca2a Ca2a MPLS-TP Segment layer Mark 14 OAL OAM Mark 13 Mark 14 OAL ACH OAM LEP CAL OAM Mark 13 LEP OAL ACH OAM Mark 14 LEP PW CAL OAM Mark 13 LEP PW OAL ACH OAM and the instrument will display flow (bandwidth utilization or CIR), packet loss (FL), round-trip delay (FD), the speed deviation (FDV), and other key indicators as well as MPLS-TP header information. Using this mode, you can conduct OAM generation and validation and analyze OAM control layer flow during operation maintenance or troubleshooting. CCM can be used to verify the link connection, and loopback/link tracking can be used to determine the fault isolation. 12

13 Test Example 2: MPLS-TP Flow Real-Time Network Monitoring When the T-BERD 6000A/8000 MSAM or T-BERD 5800 is connected to the mirror port or a free port on the router, it can be used to monitor and analyze MPLS-TP flow and implement MPLS-TP channel scan. In this example, the test instrument is configured to monitor mode to detect the real-time MPLS-TP flow switched from the switch to this mirror port. Subsequently, you can analyze the detected flow on the test instrument interface, and use a real-time display of bandwidth utilization, user channel, frames received, and other key flow statistics, as well as MPLS-TP header information such as service provider (SP), the customer ID, and prioritized items. Test Example 3: Ensure Accurate Time Synchronization Verification for 1588v2 Networks Time precision in a 1588v2 network depends on the PTP information exchange between the master and slave clock that is received constantly. Network data layer traffic can affect the PTP information transmission delay because all of them share a NE flow processor. Therefore, the use of a high-end network will affect the performance of PTP information, and eventually lead to synchronization of variation. Measure from the main NE and NE information exchanged between the PTP packet delay variation (PDV) to determine the problem. By using the T-BERD 6000A/8000 MSAM or T-BERD 5800 to measure a certain period of PDV, PTP will be able to verify that the information transmission is normal. To simulate the master/slave clock network element, the PTP protocol on the PTN network packet capture statistics, verified by analyzing the function of PTP protocol and configuration of various parameters meeting specifications, package contents from the agreement to provide specific time synchronization visual performance. The use of instruments in the fault node test, through the instrument interaction between the main clock, performance analysis of network latency, PDV, performance degradation, and failure time synchronization, pinpoints the specific location. 13

14 TDM Ethernet TDM CE IWF NTE Ethernet NTE network Ethernet network Main Primary reference source PTP information MSAM- 1588v2 Slave Synchronous packet delay variation Test Example 4: PTN One-Way Latency Test Time precision in a 1588v2 network depends on the network s two-way transmission latency symmetry. It is asymmetric in actual networks, so the accurate measurement of one-way latency in network links is extremely crucial to the direct judgment of the slave clock s recovery quality (if it meets < 3us indicators) in latency compensation and post-launch maintenance of network opening. In addition, one-way delay of the business is vital to the existing businesses that require a very high real-time quality. By using the T-BERD 6000A/8000 MSAM or T-BERD 5800, users can deploy this test. RS-232- USB Adapter TOD lnput 1PPS lnput BNC Adapter AC Test lnterface Network External GPS Rx 14

15 Test Example 5: Synchronous Ethernet Clock Synchronization Test Synchronous Ethernet is another vital technology for a PTN to realize clock synchronization. Assessing network performance is crucial for new network launches and post-launch maintenance. JDSU offers the industry s most complete test solution. Its synchronous Ethernet testing ensures clock synchronization throughout Layer 1, and is the technology that adopts the Ethernet link stream to restore the clock. Therefore, it has high accuracy and fast convergence, and its upper-packet PDV has no effect on the performance of clock synchronization. The T-BERD 6000A/8000 MSAM or T-BERD 5800 can support synchronous Ethernet testing, realize Sync-E generation and receiving verification tests, and validate if a synchronized network is working properly by measuring G.8264 SSM messaging rates and analytical validation of messages. The specific physical performance (jitter and wander) of synchronous Ethernet can be measured and validated by using the advanced JDSU Optical Network Tester, the ONT-5xx, which is the industry s leading synchronous Ethernet testing tool. Jitter/Wander Generation Jitter/Wander Tolerance Jitter/Wander Transfer Jitter Jitter-free with Jitter with Jitter SyncE SyncE SyncE Jitter measurement Event detection Jitter measurement Reference signal Reference signal Reference signal Wander SyncE With Wander SyncE BITS With Wander SyncE Wander measurement Event detection Wander measurement 15

16 Test & Measurement Regional Sales north america toll free: fax: latin america tel: fax: asia pacific tel: fax: emea tel: fax: Product specifications and descriptions in this document subject to change without notice JDS Uniphase Corporation PTN-NETWORK.BR.NSD.TM.AE January 2012