Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment

Transcription

1 Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment FAST SHIPPING AND DELIVERY TENS OF THOUSANDS OF IN-STOCK ITEMS EQUIPMENT DEMOS HUNDREDS OF MANUFACTURERS SUPPORTED LEASING/MONTHLY RENTALS ITAR CERTIFIED SECURE ASSET SOLUTIONS SERVICE CENTER REPAIRS Experienced engineers and technicians on staff at our full-service, in-house repair center SM InstraView REMOTE INSPECTION Remotely inspect equipment before purchasing with our interactive website at Contact us: (888) 88-SOURCE WE BUY USED EQUIPMENT Sell your excess, underutilized, and idle used equipment We also offer credit for buy-backs and trade-ins LOOKING FOR MORE INFORMATION? Visit us on the web at for more information on price quotations, drivers, technical specifications, manuals, and documentation

2 NI R Series Onboard FPGA chip, programmable with the LabVIEW FPGA Module User-defined triggering, timing, and decision making in hardware with 25 ns resolution Up to 8 analog inputs, independent sampling rates up to 750 khz, 16-bit resolution Up to 8 analog outputs, independent update rates up to 1 MHz, 16-bit resolution Up to 160 digital lines configurable as inputs, outputs, counters, or custom logic at rates up to 40 MHz Direct memory access (DMA) channels for high-speed data streaming Implement custom control logic, inline signal processing, and digital communication protocols Operating Systems Windows XP/2000 LabVIEW Real-Time Recommended Software LabVIEW LabVIEW FPGA Module LabVIEW code compiler for FPGAs Emulated debugging mode LabVIEW Real-Time Module Driver Software (included) NI-RIO Calibration Certificate Available Max Sampling Rate per Channel (ks/s) Max Update Rate per Channel (MS/s) Product Bus/Form Factor FPGA 16-Bit Analog Inputs 16-Bit Analog Outputs Multifunction R Series NI 7851R PXI Virtex-5 LX NI 7852R PXI Virtex-5 LX NI 7841R PXI Virtex-5 LX NI 7842R PXI Virtex-5 LX NI 7830R PCI, PXI Virtex-II 1M gates NI 7831R PCI, PXI Virtex-II 1M gates NI 7833R PCI, PXI Virtex-II 3M gates Digital R Series NI 7811R PCI, PXI Virtex-II 1M gates 160 NI 7813R PCI, PXI Virtex-II 3M gates 160 Table 1. R Series Selection Guide Digital I/O Overview Intelligent DAQ is multifunction data acquisition that features userdefined onboard processing as well as complete flexibility of I/O timing and triggering. You can configure all device functionality by creating NI LabVIEW block diagrams with the LabVIEW FPGA Module. Your block diagram executes in hardware, giving you direct, immediate control of all I/O signals on the PXI or PCI device. With R Series and LabVIEW FPGA, you can configure user-defined hardware for a wide variety of applications requiring precise timing and control such as: Data acquisition with flexible triggering and onboard processing High-speed analog and discrete control loops Pulse-width modulation (PWM) and encoder interfacing User-defined digital communication protocols Custom counters with up to 64-bit resolution Hardware-timed decision making at 40 MHz Key Features Through programming in LabVIEW FPGA, you can control each of the I/O signal lines independently or synchronize a line with other channels. You can configure the digital I/O lines as custom counter/timers, PWM channels, or communication buses for user-defined protocols. All multifunction R Series devices have dedicated analog-to-digital converters/digital-to-analog converters on every analog I/O channel. This offers specialized functionality such as multirate sampling and individual channel triggering, which are beyond the capabilities of typical data acquisition hardware. You can sample every analog input channel on an R Series device simultaneously at rates up to 750 khz, and you can program every analog output on an R Series device to update simultaneously at rates up to 1 MHz. You can also store your compiled LabVIEW FPGA application in the onboard flash memory of any R Series device and configure it for automatic loading and/or execution at power up.

3 New Virtex-5 FPGAs The new NI PXI-784x and PXI-785x R Series modules use new Virtex-5 field-programmable gate arrays (FPGAs) with improved optimization capabilities that provide faster code execution and increased code capacity. These Virtex-5 FPGAs feature a new six-input look-up table (LUT) architecture for substantially improved resource utilization as well as DSP48 slices that make it possible for you to implement more complex digital signal processing at faster rates. Previous-generation Virtex-II FPGAs use four-input LUTs for up to 16 combinations of digital logic values. The new Virtex-5 FPGAs use six-input LUTs for up to 64 combinations, increasing the amount of logic that you can implement per slice. In addition, the slices themselves are placed in closer proximity to each other to reduce the propagation delay of electrons and increase overall execution rates. The single-cycle timed loop structure in LabVIEW FPGA takes full advantage of six-input LUTs for substantially improved resource utilization. This means you can optimize more LabVIEW FPGA code to fit within Virtex-5 FPGAs and perform more operations per clock cycle. Figure 1. General logic benchmarks show that Virtex-5 FPGAs offer larger sizes when compared to Virtex-II FPGAs. Figure 2. Execution speed benchmarks show that Virtex-5 FPGAs feature faster processing capabilities when compared to Virtex-II FPGAs. For more information on LabVIEW FPGA benchmarks for Virtex-5 FPGAs, visit ni.com/info and enter lvfpgabenchmarks. 2

4 Recommended Accessories High Performance SHC68-68-RMIO High-performance shielded 68-conductor cable terminated with a VHDCI 68-pin male connector at one end and a 68-pin female D-type connector at the other end that has been specifically designed for the multifunction I/O connector on R Series intelligent DAQ devices. 1 m m Required Software for R Series Intelligent DAQ NI 781xR and 783xR devices require the LabVIEW FPGA Module 7.1 or later, and NI-RIO driver software 1.3 or later. NI 784xR and 785xR devices require the LabVIEW FPGA Module or later, and NI-RIO driver software 2.4 or later. SHC68-68-RDIO High-performance shielded 68-conductor cable terminated with a VHDCI 68-pin male connector at one end and a 68-pin female D-type connector at the other end that has been specifically designed for the digital I/O connector on R Series intelligent DAQ devices. 1 m SCB-68 Shielded I/O connector block for rugged, very low-noise signal termination for connecting to 68-pin devices. The SCB-68 also includes two general-purpose breadboard areas. Dimensions 19.5 by 15.2 by 4.5 cm (7.7 by 6.0 by 1.8 in.) SCB Low Cost SH68-C68-S General-purpose shielded cable that connects any type of R Series connector to 68-pin connector blocks. 0.5 m r5 1 m m Custom Cabling SHC68-NT-S Shielded 68-conductor cable terminated with a 68-pin male VHDCI connector at one end and unterminated bare wires at the other. Use this cable, ideal for OEM applications, to create custom cabling solutions for R Series devices. 2 m NSC Shielded cable terminated with a VHDCI 68-pin male connector at one end and two 26-pin ribbon connectors and one 50-pin ribbon connector on the other; designed to connect the R Series RMIO connector to standard ribbon cable accessories. 1 m NSC Shielded cable terminated with a VHDCI 68-pin male connector at one end and two 50-pin ribbon connectors on the other; designed to connect R Series RDIO connectors to standard ribbon cable accessories. 1 m Ordering Information PCI NI PCI-7811R NI PCI-7813R NI PCI-7830R NI PCI-7831R NI PCI-7833R PXI NI PXI-7811R NI PXI-7813R NI PXI-7830R NI PXI-7831R NI PXI-7833R NI PXI-7841R NI PXI-7842R NI PXI-7851R NI PXI-7852R Includes NI-RIO driver software. BUY NOW! For complete product specifications, pricing, and accessory information, call (U.S.) or go to ni.com/rseries. 3

5 Specifications Analog Input (NI 783xR/784xR/785xR Only) Input Characteristics Number of channels NI 7830R... 4 NI 7831R/7833R/7841R/ 7842R/7851R/7852R... 8 Input modes... DIFF, RSE, NRSE (software-selectable; selection applies to all channels) Type of ADC... Resolution bits, 1 in 65,536 Conversion time NI 783xR/NI 784xR... 4 µs NI 785xR... 1 µs Maximum sampling rate NI 783xR/NI 784xR... NI 785xR... Input impedance Powered on... Powered off/overload... Input signal range... Input bias current Input offset current Input coupling... Maximum working voltage (signal + common mode)... Successive approximation 200 ks/s (per channel) 750 ks/s (per channel) 10 GΩ in parallel with 100 pf 4.0 kω min ±10 V ±2 na ±5 na ±1 na ±5 na DC Inputs should remain within ±12 V of ground Overvoltage protection Powered on...±42 V Powered off...±35 V Data transfers...dma, interrupts, programmed I/O Accuracy Information NI 783xR Nominal Range (V) Positive Full Negative Full % of Reading 24 Hours 1 Year Absolute Accuracy Noise + Quantization Offset (µv) Single Point Averaged Temp Drift (%/ C) Absolute Accuracy at Full (±mv) Relative Accuracy Resolution (µv) Single Point Averaged , , Note: Accuracies are valid for measurements following an internal calibration. Averaged numbers assume dithering and averaging of 100 single-channel readings. Measurement accuracies are listed for operational temperatures within ±1 C of internal calibration temperature and ±10 C of external or factory-calibration temperature. Accuracy Information NI 784xR/785xR Nominal Range (V) Positive Full DC Transfer Characteristics INL DNL No missing codes CMRR, DC to 60 Hz... Settling Time Device NI 783xR NI 784xR/ 785xR Negative Full % of Reading 24 Hours 1 Year Crosstalk... Dynamic Characteristics Bandwidth NI 783xR Absolute Accuracy Noise + Quantization Offset (µv) Small signal (-3 db)... Large signal (1% THD)... NI 784xR/785xR Small signal (-3 db)... Large signal (1% THD)... Single Point Averaged Temp Drift (%/ C) ±3 LSB typ, ±6 LSB max ±1 LSB typ, ±3 LSB max -1.0 to +2.0 LSB max ±0.4 LSB typ, ±0.9 LSB max 16 bits typ, 15 bits min 16 bits guaranteed -86 db Accuracy Step Size 16 LSB 4 LSB 2 LSB ±20.0 V 7.5 µs 10.3 µs 40 µs ±2.0 V 2.7 µs 4.1 µs 5.1 µs ±0.2 V 1.7 µs 2.9 µs 3.6 µs ±20.0 V 2.1 µs 4.2 µs 8 µs ±2.0 V 1.3 µs 1.6 µs 1.8 µs ±0.2 V 0.8 µs 1.1 µs 1.2 µs -80 db, DC to 100 khz 650 khz 55 khz 1 MHz 500 khz Absolute Accuracy at Full (±mv) Analog Output (NI 783xR/784xR/785xR Only) Output Characteristics Relative Accuracy Resolution (µv) Single Point Averaged ,591 1, , Note: Accuracies are valid for measurements following an internal calibration. Averaged numbers assume dithering and averaging of 100 single-channel readings. Measurement accuracies are listed for operational temperatures within ±1 C of internal calibration temperature and ±10 C of external or factory-calibration temperature. Output type... Single-ended, voltage output Number of channels NI 7830R... 4 NI 7831R/7833R/7841R/ 7842R/7851R/7852R... 8 Resolution bits, 1 in 65,536 Update time µs Maximum update rate... 1 MS/s Type of DAC... Enhanced R-2R Data transfers... DMA, interrupts, programmed I/O 4

6 Voltage Output Range... Output coupling... Output impedance Current drive... Protection... Power-on state... Accuracy Information DC Transfer Characteristics ±10 V DC Absolute Accuracy Nominal Range (V) % of Reading Positive Negative Full Full 24 Hours 1 Year Offset (µv) 1.25 Ω 0.5 Ω ±2.5 ma Short-circuit to ground User configurable INL... ±0.5 LSB typ, ±4.0 LSB max DNL... ±0.5 LSB typ, ±1 LSB max Monotonicity bits, guaranteed Settling Time Dynamic Characteristics Slew rate V/µs Noise µv rms, DC to 1 MHz Glitch energy at midscale transition.. ±200 mv for 3 µs Digital I/O Number of channels NI 7811R/7813R NI 7830R NI 7831R/7833R/7841R/ Temp Drift (%/ C) 7842R/7851R/7852R Digital logic levels V TTL, 5 V TTL Compatible Output current Source ma Sink ma Input leakage current... ±10 µa Power-on state... Programmable, by line Data transfers... DMA, interrupts, programmed I/O Absolute Accuracy at Full (mv) , Note: Accuracies are valid for analog output following an internal calibration. Analog output accuracies are listed for operation temperatures within ±1 C of internal calibration temperature and ±10 C of external or factory calibration temperature. Temperature drift applies only if ambient is greater than ±10 C of previous external calibration. Accuracy Step Size 16 LSB 4 LSB 2 LSB ±20.0 V 6.0 µs 6.2 µs 7.2 µs ±2.0 V 2.2 µs 2.9 µs 3.8 µs ±0.2 V 1.5 µs 2.6 µs 3.6 µs Level Min (V) Max (V) Input low voltage (V IL ) 0.0 V 0.8 V Input high voltage (V IH ) 2.0 V 5.5 V Output low voltage (V OL ), 0.4 V where I OUT = -4 ma Output high voltage (V OH ), where I OUT = 4 ma 2.4 V 3.3 V Protection Input NI 781xR/783xR... NI 784xR/785xR... Output... Minimum pulse width Input... Output... Minimum sampling period NI 781xR/783xR... Reconfigurable FPGA -0.5 to 7.0 V, single line to 20.0 V, single line Short-circuit (up to eight lines may be shorted at a time) 25 ns 12.5 ns 5 ns 8.33 ns NI 7811R/7830R/7831R FPGA type... Virtex-II 1000 Number of flip-flops... 10,240 Number of 4-input LUTs... 10,240 Number of 18x18 multipliers Embedded block RAM kb NI 7813R/7833R FPGA type... Virtex-II 3000 Number of flip-flops... 28,672 Number of 4-input LUTs... 28,672 Number of 18x18 multipliers Embedded block RAM... 1,728 kb NI 7841R/7851R FPGA type... Virtex-5 LX30 Number of flip-flops... 19,200 Number of 6-input LUTs... 19,200 Number of DSP48 slices (25x18 multipliers) Embedded block RAM... 1,152 kb NI 7842R/7852R FPGA type... Virtex-5 LX50 Number of flip-flops... 28,800 Number of 6-input LUTs... 28,800 Number of DSP48 slices (25x18 multipliers) Embedded block RAM... 1,728 kb Timebases NI 781xR/783xR... Timebase reference sources NI PCI-781xR/783xR... NI PXI-78xxR... Timebase accuracy, onboard clock... Phase-locked to PXI 10 MHz clock (NI PXI-78xxR only)... 40, 80, 120, 160, or 200 MHz 40, 80, or 120 MHz Onboard clock only Onboard clock, phase-locked to PXI 10 MHz clock ±100 ppm, 250 ps peak-to-peak jitter Adds 350 ps peak-to-peak jitter 5

7 Additional frequency-dependent peak-to-peak jitter NI 781xR/783xR 40 MHz... None 80 MHz ps 120 MHz ps 160 MHz ps 200 MHz ps NI 784xR/785xR 40 MHz... None 80 MHz ps 120 MHz ps Calibration (NI 783xR/784xR/785xR Only) Recommended warm-up time... Calibration interval... Onboard calibration reference DC level... Temperature coefficient... Long-term stability minutes 1 year V (±3.5 mv) (actual value stored in flash memory) ±5 ppm/ C max ±20 ppm/ 1,000 h Note: Refer to Calibration Certificates at ni.com/calibration to generate a calibration certificate for the NI 783xR. Bus Interface PXI (NI PXI-78xxR only)... PCI (NI PCI-781xR/783xR only)... Physical Dimensions (not including connectors) NI PCI-781xR/783xR... NI PXI-78xxR... Weight NI PCI-781xR/783xR... NI PXI-78xxR... I/O connectors NI 781xR... NI 783xR/784xR/785xR... Master, slave Master, slave 17 by 11 cm (6.7 by 4.3 in.) 16 by 10 cm (6.3 by 3.9 in.) 112 g 152 g Four 68-pin female high-density VHDCI type Three 68-pin female high-density VHDCI type Maximum Working Voltage Maximum working voltage refers to the signal voltage plus the common-mode voltage. Channel-to-earth... Channel-to-channel... ±12 V, Measurement Category I ±24 V, Measurement Category I Caution: Do not use the NI 783xR/784xR/785xR for connection to signals in Measurement Category II, III, or IV. Power Requirement +5 VDC (±5%) 1 NI 781xR... 9 ma (typ), 50 ma (max) NI 7830R/7831R ma (typ), 355 ma (max) NI 7833R ma (typ), 586 ma (max) NI 7841R/7851R ma (typ), 252 ma (max) NI 7842R/7852R ma (typ), 291 ma (max) +3.3 VDC (±5%) 2 NI 7811R ma (typ), 1,000 ma (max) NI 7813R ma (typ), 1,350 ma (max) NI 7830R/7831R ma (typ), 660 ma (max) NI 7833R ma (typ), 1,148 ma (max) NI 7841R/7851R ma (typ), 1,244 ma (max) NI 7842R/7852R ma (typ), 1,484 ma (max) +12 V 0.5 A -12 V 0.25 A +5 V terminal Connector A max Connector A max Connector A max All connectors A max 3 To calculate the total current sourced by the digital outputs use the following equation: j current sourced on channel i i=1 Power available at I/O connectors to 5.25 VDC at 1 A total, 250 ma per I/O connector pin 1 Does not include current drawn from the +5 V line on the I/O connectors. 2 Does not include current sourced by the digital outputs. 3 The NI 784xR/785xR devices have a user-replaceable socketed fuse that opens when current exceeds the current specification. Refer to the R Series Intelligent DAQ User Manual, available at ni.com/manuals, for information about fuse replacement. 6

8 Environmental NI 78xxR devices are intended for indoor use only. Operating Environment NI 781xR... 0 to 55 C (tested in accordance with IEC and IEC ) NI 7830R, NI 7831R 40 or 80 MHz timebase... 0 to 55 C (tested in accordance with IEC and IEC ) NI 7833R/7841R/7842R/7851R/7852R 40 MHz timebase... 0 to 55 C (tested in accordance with IEC and IEC ) 80 MHz timebase... 0 to 55 C except the following: 0 to 45 C when installed in an NI PXI-1000/B or NI PXI-101x (tested in accordance with IEC and IEC ) Relative humidity range to 90%, noncondensing (tested in accordance with IEC ) Altitude... 2,000 m at 25 C ambient temperature Storage Environment Ambient temperature range... Relative humidity range to 70 C (tested in accordance with IEC and IEC ) 5 to 95%, noncondensing (tested in accordance with IEC ) Note: Clean the device with a soft, nonmetallic brush. Make sure that the device is completely dry and free from contaminants before returning it to service. Shock and Vibration (for NI PXI-78xxR Only) Operational Shock... Random Vibration Operating... Nonoperating g peak, half-sine, 11 ms pulse (tested in accordance with IEC ; test profile developed in accordance with MIL-PRF-28800F) 5 to 500 Hz, 0.3 g rms 5 to 500 Hz, 2.4 g rms (tested in accordance with IEC ; nonoperating test profile exceeds the requirements of MIL-PRF-28800F, Class 3) Safety and Compliance Safety NI 78xxR devices are designed to meet the requirements of the following standards of safety for electrical equipment for measurement, control, and laboratory use: IEC , EN UL , CSA Note: For UL and other safety certifications, refer to the product label or visit ni.com/certification, search by model number or product line, and click the appropriate link in the Certification column. Electromagnetic Compatibility This product is designed to meet the requirements of the following standards of EMC for electrical equipment for measurement, control, and laboratory use: EN EMC requirements; Minimum Immunity EN Emissions; Group 1, Class A CE, C-Tick, ICES, and FCC Part 15 Emissions; Class A Note: For EMC compliance, operate this device according to product documentation. CE Compliance This product meets the essential requirements of applicable European Directives, as amended for CE marking, as follows: 2006/95/EC; Low-Voltage Directive (safety) 2004/108/EC; Electromagnetic Compatibility Directive (EMC) Note: Refer to the Declaration of Conformity (DoC) for this product for any additional regulatory compliance information. To obtain the DoC for this product, visit ni.com/certification, search by model number or product line, and click the appropriate link in the Certification column. Environmental Management National Instruments is committed to designing and manufacturing products in an environmentally responsible manner. NI recognizes that eliminating certain hazardous substances from our products is beneficial not only to the environment but also to NI customers. For additional environmental information, refer to the NI and the Environment Web page at ni.com/environment. This page contains the environmental regulations and directives with which NI complies, as well as other environmental information not included in this document. Waste Electrical and Electronic Equipment (WEEE) EU Customers: At the end of their life cycle, all products must be sent to a WEEE recycling center. For more information about WEEE recycling centers and National Instruments WEEE initiatives, visit ni.com/environment/weee.htm. 7

9 NI Services and Support MAINTAIN DEPLOY SERVICE NEEDS Training and Certification NI has the services and support to meet your needs around the globe and through the application life cycle from planning and development through deployment and ongoing maintenance. We offer services and service levels to meet customer requirements in research, design, validation, and manufacturing. Visit ni.com/services. NI training is the fastest, most certain route to productivity with our products. NI training can shorten your learning curve, save development time, and reduce maintenance costs over the application life cycle. We schedule instructor-led courses in cities worldwide, or we can hold a course at your facility. We also offer a professional certification program that identifies individuals who have high levels of skill and knowledge on using NI products. Visit ni.com/training. Professional Services Our NI Professional Services team is composed of NI applications and systems engineers and a worldwide National Instruments Alliance Partner program of more than 600 independent consultants and integrators. Services range from start-up assistance to turnkey system integration. Visit ni.com/alliance. OEM Support PLAN DEVELOP We offer design-in consulting and product integration assistance if you want to use our products for OEM applications. For information about special pricing and services for OEM customers, visit ni.com/oem. Local Sales and Technical Support In offices worldwide, our staff is local to the country, giving you access to engineers who speak your language. NI delivers industry-leading technical support through online knowledge bases, our applications engineers, and access to 14,000 measurement and automation professionals within NI Developer Exchange forums. Find immediate answers to your questions at ni.com/support. We also offer service programs that provide automatic upgrades to your application development environment and higher levels of technical support. Visit ni.com/ssp. Hardware Services NI Factory Installation Services NI Factory Installation Services (FIS) is the fastest and easiest way to use your PXI or PXI/SCXI combination systems right out of the box. Trained NI technicians install the software and hardware and configure the system to your specifications. NI extends the standard warranty by one year on hardware components (controllers, chassis, modules) purchased with FIS. To use FIS, simply configure your system online with ni.com/pxiadvisor. Calibration Services NI recognizes the need to maintain properly calibrated devices for high-accuracy measurements. We provide manual calibration procedures, services to recalibrate your products, and automated calibration software specifically designed for use by metrology laboratories. Visit ni.com/calibration. Repair and Extended Warranty NI provides complete repair services for our products. Express repair and advance replacement services are also available. We offer extended warranties to help you meet project life-cycle requirements. Visit ni.com/services. ni.com National Instruments info@ni.com *351588A-01* A D 2008 National Instruments Corporation. All rights reserved. LabVIEW, National Instruments, National Instruments Alliance Partner, NI, ni.com, and SCXI are trademarks of National Instruments. Other product and company names listed are trademarks or trade names of their respective companies. A National Instruments Alliance Partner is a business entity independent from NI and has no agency, partnership, or joint-venture relationship with NI.

10 Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment FAST SHIPPING AND DELIVERY TENS OF THOUSANDS OF IN-STOCK ITEMS EQUIPMENT DEMOS HUNDREDS OF MANUFACTURERS SUPPORTED LEASING/MONTHLY RENTALS ITAR CERTIFIED SECURE ASSET SOLUTIONS SERVICE CENTER REPAIRS Experienced engineers and technicians on staff at our full-service, in-house repair center SM InstraView REMOTE INSPECTION Remotely inspect equipment before purchasing with our interactive website at Contact us: (888) 88-SOURCE WE BUY USED EQUIPMENT Sell your excess, underutilized, and idle used equipment We also offer credit for buy-backs and trade-ins LOOKING FOR MORE INFORMATION? Visit us on the web at for more information on price quotations, drivers, technical specifications, manuals, and documentation