APPROVAL SHEET. 10Gbps XFP Transceiver, 80km Reach X55-64D80-RLP R&D QA CEO

Transcription

1 APPROVAL SHEET Project Name Product Name Model Name 10Gbps XFP Transceiver, 80km Reach X55-64D80-RLP Approval Code Reporting Date Approval Date Customer Maker R&D QA CEO Maker : FOTTU CO., LTD Address : Room 2306, A tower, Gunpo IT Valley, 1045 Dangieong-dong, Gunpo-city Gyeonggi-province, Korea Contact : Hyunsam Lee (TEL: ) FAX: sam@fottu.com

2 승인원이력 LIST 이력변경날짜항목 / 내용변경사유비고 Rev 초도제정 9 페이지 * 특이사항 * 2/9

3 X31-64D10-RLP 10Gbps XFP Transceiver, 80km Reach Product Features Compliance with Digital Diagnostic Monitoring Hot-pluggable capability Maximum link length of 80km with SMF Cooled 1550nm EML laser XFP MSA package with duplex LC connector No reference clock required Single +3.3V power supply 2-Wire Data Transfer Protocol RoHS Compliant Applications 10GBASE-LR/LW 10G Ethernet Absolute Maximum Rating Parameter Symbol Min. Max. Unit Note Power Supply Voltage Vcc 0 4 V Soldering Temperature C 10 seconds on leads only Storage Temperature Tstg C 0% ~ 85% RH Recommended Operating Condition Parameter Symbol Min. Typ. Max. Unit Power Supply Voltage Vcc V Total Current Icc3 750 Icc5 500 ma Operating Temperature(NOTE1) Top 0 70 C Data Rate Gbps NOTE1: Measured on top side front center of SFP module. 3/9

4 Transmitter Specifications (Tc=0~70 C, Unless otherwise specified) Parameter Symbol Min. Typ. Max. Unit Note Average Launched Power Po 0 4 dbm Emission Center Wavelength c nm Spectral nm Average Output Power(Laser off) Pout-off -30 dbm Side Mode Suppression Ratio SMAR 30 db Extinction Ratio (Dynamic) ER 9 db Relative Intensity Noise RIN12OMA -128 db/hz Optical Return Loss Tolerance ORLT 12 db Transmitter Reflectance TR -12 db Transmitter and Dispersion Penalty TDP 3.2 db Input Different Impedance Zin Ω Differential Data Input Swing Vin,p-p mvp-p Eye Pattern Mask Compliant with IEEE TxFault_High VEN VCCT V TxFault_Low VDIS V Tx Disable Voltage VEN 2 - VCCT V Tx Enable Voltage VDIS V LVTTL LVTTL Receiver Specifications(Tc=0~70 C, Unless otherwise specified) Parameter Symbol Min. Typ. Max. Unit Note Maximum Input Power Pin -8 - dbm Receiving Wavelength c nm Receiver Sensitivity Ps dbm Note1 Receiver Reflectance Ref -12 db Differential Data Output Amplitude Vin,p-p 650 mvp-p Input Differential Impedance Zin Ω LOS Assert Level Pa dbm LOS Deassert Level Pd dbm LOS Hysteresis db LOS Voltage-Low VSD_L V LOS Voltage-High VSD_H 2 Vcc V Note1: PRBS2 31-1@ Gbps, BER E-12 4/9

5 Management Interface The digital diagnostic memory map specific data field defines as following. 5/9

6 Pin Function Definitions Pin Logic Symbol Name/Description Ref 1 GND Module Ground 1 2 VEE5 Optional 5.2 Power Supply Not required 3 LVTTL-I Mod- Desel Module De-select; When held low allows the module to, respond to 2- wire serial interface commands 4 LVTTL-O Interrupt Interrupt (bar); Indicates presence of an important condition which can be read over the serial 2-wire interface 2 5 LVTTL-I TX_DIS Transmitter Disable; Transmitter laser source turned off 6 VCC5 +5 Power Supply 7 GND Module Ground 1 8 VCC3 +3.3V Power Supply 9 VCC3 +3.3V Power Supply 10 LVTTL-I SCL Serial 2-wire interface clock 2 11 LVTTL- I/O SDA Serial 2-wire interface data line 2 6/9

7 12 LVTTL-O Mod_Abs Module Absent; Indicates module is not present. Grounded in the 2 module 13 LVTTL-O Mod_NR Module Not Ready; 2 14 LVTTL-O RX_LOS Receiver Loss of Signal indicator 2 15 GND Module Ground 1 16 GND Module Ground 1 17 CML-O RD- Receiver inverted data output 18 CML-O RD+ Receiver non-inverted data output 19 GND Module Ground 1 20 VCC2 +1.8V Power Supply Not required 21 LVTTL-I P_Down/R ST Power Down; When high, places the module in the low power stand-by mode and on the falling edge of P_Down initiates a module reset Reset; The falling edge initiates a complete reset of the module including the 2-wire serial interface, equivalent to a power cycle. 22 VCC2 +1.8V Power Supply Not required 23 GND Module Ground 1 24 PECL-I RefCLK+ 25 PECL-I RefCLK- Reference Clock non-inverted input, AC coupled on the host board Not required Reference Clock inverted input, AC coupled on the host board Not required 26 GND Module Ground 1 27 GND Module Ground 1 28 CML-I TD- Transmitter inverted data input 29 CML-I TD+ Transmitter non-inverted data input 30 GND Module Ground 1 Notes: 1. Module circuit ground is isolated from module chassis ground within the module. 2. Open collector, should be pulled up with 4.7k 10k ohms on host board to a voltage between 3.15Vand 3.6V. 3. A Reference Clock input is not required /9

8 Recommended Host Board Power Supply Circuit Recommended High-speed Interface Circuit 8/9

9 Mechanical Diagram Dimensions are in millimeters. Tolerances are ±0.2mm, unless otherwise specified Ordering Information 제품명설명 Latch Color Remark X55-64D80-RLP 10Gbps LC/PC XFP White 9/9