ma & THERMOCOUPLE SIMULATORS CALIBRATORS

Transcription

1 ma & THERMOCOUPLE SIMULATORS CALIBRATORS Features Model CCMA: Easy to use pocket checker for simulating current loops Instantly determines if your device needs calibration or if a sensor needs to be replaced Simulates output ranges of 4 ma, 12 ma and 20 ma Accurate to 0.1 ma Overload indication when load exceeds 240Ω Compact case features push button output selector switch and bright red LEDs that indicate simulation output or battery status Complete with 9V battery and calibration cable terminated with spade plugs Dimensions/Weight: 89 x 58.4 x 25.4mm / 284g Features Model CCTEMPK: Provides a quick and easy way of checking the calibration of type K thermocouple devices or controllers Simulates 4 common values in C and F Ranges: 32 F (0 C), 212 F (100 C), 932 F (500 C) and 1832 F (1000 C) Accuracy: ±(0.25% + 1 C or F) Complete with 9V battery, vinyl pouch case and 60" calibration cable terminated with subminiature connector Dimensions/Weight: 89 x 58.4 x 25.4mm / 284g CC-MA Current Loop Simulator $ CC-TEMPK Type K Thermocouple Simulator $ Features Model CC-421: Current Source: 0 to 24 ma, 2 ranges Current Measurement: 0 to 24 ma, 2 ranges Power and Current Measurement of 2-wire loop: 0 to 24mA, 2 ranges DC mv Source: mv to mv Current calibrator drives loads up to 500Ω Sampling Time: Approx. 0.4 second Dimensions/Weight: 185 x 78 x 38mm / 265g Features Model CC-422: Adjustable 0 to 24 ma current source, 2 ranges Range/Resolution: 0 to ma/0.01 ma; 0 to 24.0 ma/0.1 ma Current calibrator drives loads up to 500Ω Sampling Time: Approx. 0.4 second Dimensions/Weight: 185 x 78 x 38mm / 265g Features Model TC-920: Type K thermocouple thermometer and calibrator in one unit Range: -199 to 1230 C (-325 to 2246 F) Fahrenheit/Celsius switchable Data Hold High precision, temperature linearity compensation circuit Accepts any standard Type K thermocouple probe RS-232 serial computer interface Dimensions/Weight: 185 x 78 x 38mm / 280g 222 M2500E CC-421 Voltage/Current Calibrator $ CC-422 Current Calibrator $ TC-920 Thermometer/Temperature Calibrator $338.00

2 Features Model 707 & 705: Innovative output adjustment dial on 707 provides 1µA and 100µA resolution and one-hand operation Large display and simple interface for ease of use Simultaneous ma and % readout for quick, easy interpretation of readings maaccuracy of 0.015% on the 707 and 0.02% on the 705 HART mode on the 707 connects 250Ω resistor in series with 24V loop for compatibility with HART communicators Push button 25% steps for fast, easy linearity checks "Span Check" for fast confirmation of zero & span Selectable slow and fast linear step ramp provide ramping outputs for valve slewing, remote testing and loop functional tests 24V internal loop supply so you can power and read a transmitter at the same time without carrying a DMM 0-20mA or 4-20mA default start up modes Includes C-10 protective yellow holster, TL75 test leads, AC72 test clips and instruction sheet Features Model 715: Measure loop current (0-20mA, 4-20mA) signals with 0.015% accuracy and 1µA resolution Measure voltage output process signals from PLCs, transmitters Source or simulate 24mA loop current Source voltage to 100mV or 10V 24V loop supply with simultaneous current measurement Includes C-81Y protective yellow holster with Flex-Stand, test leads and alligator clips, 9V alkaline battery and instruction sheet Features Model 707Ex: Includes the great features of the standard 707 Certified in accordance with ATEX directive (EX II 2 G Eex ia IIC T4) & FM Class 1, Division 2, Group A-D LOOP CALIBRATORS Model 705 & VOLTAGE MEASUREMENT Range 0 to 28V 0 to 100mV, 0 to 10V Resolution 1mV 10µV, 1mV Accuracy 705: 0.025% rdg + 1 LSD 0.02% rdg. + 2 LSD 707: 0.015% rdg + 2 LSD CURRENT MEASUREMENT Range 0 to 24mA 0 to 24mA Resolution 0.001mA 0.001mA Accuracy 705: 0.02% rdg + 2 LSD 0.015% rdg. + 2 LSD 707: 0.015% rdg + 2 LSD CURRENT SOURCING Range 0 to 20mA or 4 to 20mA 0 to 20mA or 4 to 20mA Accuracy 705: 0.025% rdg + 2 LSD 0.015% rdg. + 2 LSD 707: 0.015% rdg + 2 LSD Drive Capability 705: 24mA 24mA 707: 24mA Measurement Loop Power 24V 24V Voltage Sourcing n/a 0 to 100mV or 0 to 10V Display Current & % Span Yes ma or % Auto Step, Auto Ramp Yes No Span Check Yes No 705 Loop Calibrator $ Loop Calibrator $ Ex Intrinsically Safe Loop Calibrator $ Volt/mA Calibrator $ M1726E 223

3 LOOP CALIBRATOR Perform field calibration of 2-wire transmitters, receivers, recorders, and controllers with Model LC21 Smart Loop Calibrator. The portable LC21 calibrator sources 24VDC, reads 0 to ma and simulates 2-wire transmitters. Unit features continuous output or fixed step current output. Use fixed calibration currents to test and calibrate equipment or to control valve stroking. Output currents can be changed manually or automatically. The LC21 calibrator can source or simulate continuous up/down cycling between 4 and 20 ma or 0 and 20 ma -- ideal for endurance testing. Display readings in ma or in % of 4-20 ma or 0-20 ma. Unit includes 13" (33cm) long leads, carrying case, batteries, spare fuse, and manual. Output Range: 0 to ma Input Range: 0 to ma Accuracy: ±0.05% of range Resolution: 10 µa Internal Loop Power: 24 VDC stabilized External Loop Power: 56 VDC maximum Fixed Steps: 4-20 ma lin: ; 0-20 ma lin: ; 4-20 ma sq. rt (flow): ; 0-20 ma sq. rt (flow): ; 4-20 ma valve: Fixed Step Interval: 10 seconds in auto-stepping mode Auto-Ramping Interval: 60 seconds between limits Temp. Effect: % per F, 0.003% per C Drive Capability: 900Ω Power Supply: Four AA 1.5V alkaline batteries Battery Life: Sources: 13 hrs; Measures: 64 hrs Dimensions: 4.88 x 3.0 x 0.84" (124 x 76.2 x 21.3mm) Weight: 9 oz (285 g) LC21 Smart Loop Calibrator $ V/60Hz Line Adapter $90.00 UPS-15 Intrisically BAE $ Provides source and measurement of ten (10) common thermocouples, as well as mv High accuracy ±3 C (Type J thermocouple, all errors combined) Accepts both thermocouple mini-plugs and bare thermocouple wires Simple decade control of output Three (3) setpoints for each T/C type MIN/MAX recall in measure mode Large knob for decade control of the output in source mode Input protection to 240 VAC GENERAL 224 THERMOCOUPLE CALIBRATOR CJC Temp. Offset: ±0.05 C/ C outside of 23±5 C Warm-up Time: 1 minute to specification Operating Temp.: -10 C to +55 C Power Supply: 9V alkaline battery; 006P/ IEC 6F22/ NEDA Optional NiCad. Optional AC adapter/ charger Dimensions: 5.7 x 3.15 x 1.43" (14.47 x 8.00 x 3.63 cm) Weight: 12 oz (340 g) M1725E OUTPUT VOLTAGE Range/Resolution: -10 to mv / 1 µv Accuracy: ±0.007% rdg., ±10 µv Output Impedance: 1Ω INPUT VOLTAGE Range/Resolution: -10 to mv / 1 µv Accuracy: ±0.007% rdg., ±10 µv Input Impedance: > 1MΩ THERMOCOUPLE SOURCE/ MEASURE Types: J, K, T, E, R, S, B, L, U, C Resolution: Source: ±0.1 C/ F; Measure: ±0.01 C/ F ACCURACY J ±0.5 C: -210 to -100 C; ±0.3 C: -100 to 1200 C K ±0.6 C: -200 to 100 C; ±0.35 C: -100 to 1000 C; ±0.5 C: 1000 to 1372 T ±0.7 C: -200 to -150 C; ±0.3 C: -150 to 400 C E ±0.5 C: -200 to -100 C; ±0.3 C: -100 to 1000 C R ±1.8 C: 0 to 250 C; ±1.0 C: 250 to 1767 C S ±1.8 C: 0 to 250 C; ±1.0 C: 250 to 1767 C B ±1.7 C: 600 to 1000 C; ±1.2 C: 1000 to 1820 C L ±0.5 C: -200 to -100 C; ±0.4 C: -100 to 900 C U ±0.7 C: -200 to 0 C; ±0.3 C: 0 to 600 C C ±0.4 C: 0 to 1000 C; ±0.7 C: 1000 to 1800 C; ±1.2 C: 1800 to 2316 C TC100 Thermocouple Calibrator $983.00

4 MULTI-FUNCTION CALIBRATOR Accuracy ±0.6 C T/C ±0.3 C RTD and 0.015% electrical Choose either read or source modes Operates with external pressure modules 10 T/C types; 8 RTD types plus YSI 400 series thermistor (medical applications) Full function 4 to 20 ma read, source, simulate and read/ power modes with 0.015% reading accuracy Source 0 to 10 volts or read 0 to 20 volts with 0.015% of reading accuracy Measure 0 to 250 VDC or VAC Direct keyboard entry allows for quick output changes Store up to nine setpoints for each output function RTD function works with all pulsed XMTR's RS232 Interface The MC-1000 combines the accuracy and functions of our next generation PTC-8000 temperature calibrator with V/mA and frequency functions added. The performance level is twice that of similarly priced products and will calibrate virtually any process device. Pressure Ranges: See specifications for 700 Series Modules on page 249 T/C Ranges: J, K, T, E, R, S, N, B, L, U; 10 to 70 mv RTD Ranges: Pt385 (100, 200, 500, 1000Ω) Pt392, JIS, Ni120, CU10, YS1400 Ohms Ranges: 0 to and to ma Range: 0 to ma Voltage: (Low) Input/ Output V (High) Input only VDC or VAC Frequency: CPM; Hz; khz Continuity: 0 to 400.0Ω, audible tone when under 10Ω Accuracy: T/C Type J: ± 3C ±10 µv (± 0.6 C total error) RTD PT100: ±1 C ±0.75Ω (±0.3 C total error) 400Ω: ±0.1Ω; 4000Ω: ±0.1Ω ma Compliance: Up to 1000 Ω load Drive Capability: 1 ma RTD IEX-range: 0.01 ma to 3 ma RTD Freq. Response: 10 ms - works with all pulsed XMTR's Power Supply: 4 AA alkaline batteries, 25 hours typical operating time Dimensions: 7.5" x 4" x 1.5" CURRENT/VOLTAGE CALIBRATOR Remarkable 0.015% of reading accuracy Four ranges; 200 mv, 2 V, 20 V and 24 ma RS-232 interface - can be computer controlled Built-in 24V supply can drive 4 to 20 ma loops over 1000Ω Intuitive, easy to use controls Rugged lightweight, hand-held case Range Min Max Accuracy (% rdg. ± cts.) mv % ±2 V % ± % ±2 ma % ±2 The MC-1000 also combines several DMM functions like voltage measurement to 250 V AC or DC and a continuity test function. This combination of a high accuracy calibrator along with common DMM functions makes the MC-1000 the only instrument you may ever need to maintain and calibrate your instrumentation. MC1000 Multi-function Calibrator $ The all new IVC-222HPII has the capability to store and recall up to two values in the setpoints provided by the SP1 and SP2 keys. The IVC-222HPII has a RS-232 port which can be accessed via a custom cable available allowing the unit to be computer controlled for automated testing. Voltage Output ma Output Output Range: 200mV, 2V, 20V 24mA Resolution: 0.01 mv 0.1mV 1 mv 1mA Accuracy: ±0.015% rdg. ±2 cts. Temperature Stability: 0 to 18 C; 28 to 50 C Load Capability: ±1 ma for rated accuracy 1000Ω Capacitive Load: No limitations N/A Output Protection: Current limited internal reset Power Supply: 9V alkaline battery or optional NiCd Dimensions: 1.43 x 3/15 x 5.7" Weight: 12 oz. M1523E IVC222HPII Current/Voltage Calibrator $ C232SJ RS-232 Cable w/ Miniature Plug $ V NiCd Battery $ V Optional A/C Adapter/Charger $

5 Measure and source 13 types of thermocouples, 13 types of RTDs, current, voltage, frequency, and pulse trains Isolated ma/v readback circuit for complete transmitter calibration Pressure module communication port compatible with Fluke 700 series, Mensor and Martel pressure modules Large, backlit, menu-driven graphical display ensures simple operation Arrow keys and direct numeric keypad entry for quick, precise setting of output parameters All source modes can be programmed with dedicated setpoints to speed calibration and linearity tests Built-in 250Ω resistor for Hart compatibility Compatible with smart transmitters and PLCs Highest accuracy in class to 0.015% of reading Full fuseless protection to 240VAC Serial communication port for full control with ASCII commands Operates with common AA batteries or optional rechargeable batteries Meets CE requirements and is designed to IEC 1010 safety standards Accessories include test leads, carrying case, 4 alkaline batteries, NIST certificate and instruction manual The new MC-1200 multi-function calibrator provides the functions and accuracy associated with fixed-installation, laboratory instruments. It has everything needed for virtually any calibration task. A communications port compatible with Fluke 700 series, Mensor and Martel pressure modules, and an isolated ma/v read-back circuit. the accuracy and stability of the MC-1200 provides first class performance specified in demanding real-world conditions. GENERAL Stability: Power Supply: Dimensions: Weight: 226 MULTI-FUNCTION CALIBRATOR ±0.005% of reading/ C outside of 23 C ±5 C 6 VDC, 4 x AA batteries, alkaline or rechargeable 7.5 x 4.0 x 1.5 (190.5 x x 38.1mm) 20.0 oz (567g) M1727E VOLTAGE SOURCE AND READ Source Range: to VDC Read Range: Isolated: to VDC; Non-isolated: to VDC Accuracy: ±0.015% of reading ± 2 mv THERMOCOUPLE mv SOURCE AND READ Range: to mv Accuracy: ±0.02% of reading ± 10 µv CURRENT SOURCE AND READ Source Range: to ma Read Range: Isolated: to ma; Non-isolated: to ma Accuracy: ±0.015% of reading ± 2 µa FREQUENCY SOURCE AND READ CPM Range: 2.0 to CPM CPM Accuracy: ±0.05% of reading, maximum Hz Range: 1.0 to Hz Hz Accuracy: ±0.05% of reading, maximum khz Range: 1.0 to khz khz Accuracy: ±0.05% of reading, maximum ma Range: 0 to ma PULSE SOURCE only Source Range: 1 to pulses; 2 CPM to 10kHz Ohms Source: 5.0 to 4000 Ω Ohms Read: 0.00 to Ω Ohms Accuracy: 400Ω Range: ±0.025% of reading ± 0.05 Ω; 4000Ω Range: ±0.025% of reading ± 0.5 Ω THERMOCOUPLE SOURCE AND READ T/C Type Range Accuracy J to C ±0.2 C K to C ±0.3 C T to C ±0.2 C E to C ±0.2 C R to C ±1.2 C S to C ±1.2 C B to C ±1.2 C C 0 to C ±0.6 C XK to C ±0.2 C BP 0 to C ±0.9 C L to C ±0.2 C U to C ±0.25 C N to C ±0.4 C RTD SOURCE AND READ RTD Type Range Accuracy Ni120 (672) to C ±0.2 C Pt100 (385) to C ±0.2 C Pt100 (3926) to C ±0.2 C Pt100 (3916) to C ±0.2 C Pt200 (385) to C ±0.8 C Pt500 (385) to C ±0.4 C Pt1000 (385) to C ±0.2 C Cu to C ±1.4 C YSI to C ±0.1 C Cu to +200 C ±0.4 C Cu to +200 C ±0.3 C Pt to C ±1.4 C PT to C ±0.4 C MC1200 Multi-function Calibrator $

6 TEMPERATURE CALIBRATOR Accuracy ±0.4 C type J T/C and ±0.3 C 4-wire PT385 RTD, all errors included 10 thermocouple types and 8 RTD types including Pt385 (1000Ω) and Cu (10Ω) Store up to 9 setpoints for each output function Direct keyboard entry or scroll control of output RTD simulation works with all pulsed transmitters YSI400 thermistor range for medical applications Standard mini-plug or banana jack connections for thermocouples RS232 Interface NEMA 4 rated case The PTC-8001 combines virtually all widely used thermocouple and RTDs into one device. The PTC-8001 is especially valuable for calibrating smart or pulsed RTD transmitters where many other calibrators fail to work or operate at reduced accuracy specifications. RTD CALIBRATOR T/C Ranges: J, K, T, E, R, S, N, B, L, U; 10 to 70 mv RTD Ranges: Pt385 (100, 200, 500, 1000Ω) Ohms Ranges: 0 to and to Accuracy: Type J T/C: ± 0.3 C ±10 µv (± 0.6 C total error); RTD PT100: ±0.1 C ±0.075Ω (±0.3 C total error); 400Ω: ±0.1Ω; 4000Ω: ±1.0Ω RTD IEX-Range: 0.01 to 3 ma RTD Freq. Response: 10 ms - works with all pulsed XMTR's Power Supply: 4 AA alkaline batteries Battery Life: 50 hours typical Dimensions: 7.5 x 4 x 1.5" PTC-8001 Temperature Calibrator $ High accuracy source/read capability Easy-to-read super-twist LCD Intuitive, easy to use controls Rugged, dust tight, water resistant, case Powered by a common 9V battery Ranges: PT395: -200 to 850 C; PT392: -200 to 850 C Ni120: -80 to 320 C; JIS392: -200 to 850 C Selectable C or F Resolution: 1 C or F Accuracy: ±1 C (18 to 28 C) Temp. Stability: 0.01% f.s./ C (0 to 18 C & 28 to 50 C) Step Size: 100 C/100 F Scroll Size: 1 C/1 F Excitation Range: 0.125mA to 2mA continuous DC Dimensions: 1.43 x 3.15 x 5.7" Weight: 12 oz. M1728E T130 RTD Calibrator $

7 TEMPERATURE CALIBRATOR View source and measure values simultaneously on a clear, twochannel display Measure RTD's, thermocouples, ma, volts and ohms to test sensors and transmitters Source/simulate 7 RTDs, 10 thermocouples, volts and ohms to calibrate transmitters Perform fast linearity tests with 25% and 100% stepping Conduct remote tests with autostep and auto-ramp features Power transmitters using loop supply with simultaneous ma measurement Store eight frequently-used test setups for later use Small, streamlined shape, with protective urethane overmold, makes it easy to carry Backlight lets you work in poor light EMI tolerant, dust- & splash-resistant Each calibrator includes TL75 Test Leads, AC70 Test Clips, one pair of stackable test leads and user's manual Function (M or S) Range or Type Resolution Accuracy Voltage 0 to 100 mv 0.01 mv 0.02% rdg. + 2 LSD 0 to 10 V (source) 0.01V 0 to 30 V (measure) 0.01 V ma (Measure only) 0 to 24 ma ma 0.02% rdg. + 2 LSD mv (TC terminals) mv to mv 0.01 mv 0.025% range + 1 LSD Resistance 15Ω to 3200Ω 0.01Ω to 0.1Ω 0.10Ω to 1.0Ω Frequency 2.0 to 1,000.0 CPM 0.1 CPM ±0.05% 1 to 1100 Hz 1 Hz ±0.05% 1.0 to 10.0 khz 0.1 khz ±0.25% Loop Supply 24 VDC n/a 10% Thermocouples J, K, T, E, L, N, U 0.1 C, 0.1 F to 0.7 C Thermocouples B, R, S 1 C, 1 F to 1.4 C RTDs Ni120 (672), 0.1 C, 0.1 F to 0.2 C Pt100, 200, 500, 1000 (385) Pt100 (3916), Pt100 (3926) Power Supply Four "AA" alkaline batteries Battery Life 25 hours typical Dimensions 96 x 200 x 47 mm (3.8 x 7.9 x 1.9") Weight 650 g (23 oz) 724 Temperature Calibrator $ Features Model 712: Compatible with pulsed current transmitters Measure temperature from RTD output probe Simulate RTD output Operates with 7 types of RTD Measure additional RTDs using Ohms measurement function Simulate additional RTDs using Ohms source function F or C selectable Four shrouded banana jacks 228 TEMPERATURE CALIBRATORS Features Model 714: Measure temperature from thermocouple output probe Simulate thermocouple output Operable with 9 types of thermocouples Calibrate linear T/C transmitter with mv source function Selectable F or C Thermocouple mini-jack termination Available as accessories: 700TC1 and TC2 Thermocouple Mini-plug Kits M1729E Model Function Range Resolution Accuracy 712 Measure/simulate -200 to 800 C 0.1 C, 0.1 F 0.33 C, 0.6 F RTD (Pt 100) (Pt 100) Measure/simulate Ω 15 Ω to 3200 Ω 0.1Ω 0.1 Ω to 1 Ω 714 Measure/simulate T/C -200 to 1800 C 0.1 C or F 0.3C C + 10 µv depending on type (1 C or F; BRS) (K, -200 to 1370 C) Measure/simulate mv -10 to 75 mv 0.01 mv 0.025% + 1 ct Maximum Voltage 30 V Shock 1m drop test Safety CSA C22.2 No :1192 EMC EN :1992 & EN55022:1994 Class B Operating Temperature -10 to 55 C Power Supply 9V alkaline battery Battery Life 4 to 20 hours, typical Dimensions 187 x 87 x 32 mm (7.35 x 3.41 x 1.25") Weight 330 g (12 oz) 712 RTD Calibrator $ Thermocouple Calibrator $

8 PROCESS CALIBRATOR Calibrate temperature, pressure, voltage, current, resistance and frequency Simultaneously measure and source Automatically capture calibration results Document procedures and results to meet ISO 9000 and other government requirements Measure/simulate 11 types of thermocouples and eight RTDs Four types of built-in automated calibration procedures; linear transmitter, square root devices, one and two-point limit switches User-entered values to capture readings observed, measured or sources by other devices Custom units to capture data in measurement units not directly supported by the calibrator, e.g. ppm or rpm Optional shunts support ma/ma applications Built-in calculator permits readings to be recalled from the measurement function, or to store calculation results to a source function Autostep permits the calibrator to be used as a remote, continuously varying test source Programmable measurement delay supports slowly responding instruments Store up to 8,000 readings in data logging mode (743B and 744 only) PC interface (743B and 744 only) Operates in English, French, German, Italian, and Spanish Protected against dirt, dust, and moisture; unaffected by vibration 741B Documenting Calibrator The 741B is the economical choice for plants that don't use PC's or that require traditional paper forms. It has storage capacity for a day's calibration and measurement data. When you're back at the shop, recall the data on screen to fill out calibration forms. 743B More Memory, plus a PC Interface and Data Logging The 743B has all the capabilities of the 741B, plus a PC interface that lets you download procedures, lists and instructions created with software - or upload data for printing, archiving and analysis. With its expanded memory, the 743B can hold a full week of calibrations and procedures. 743B Communicates with HART Instruments The Fluke 744 offers all of the capabilities of the 743B, plus the ability to calibrate, maintain, and troubleshoot HART instrumentation. Integrated HART communication functions permit you to monitor, control, and calibrate HART instrumentation. It handles fast pulsed instruments such as RTD transmitters and PLCs, with pulses as short as 1ms. Every Fluke 741B and 743B comes with two sets of TL224 industrial test leads, two sets of AC test clips, one set of TP220 test probes, a BP7217 battery pack and charger, an instruction manual, and all units are shipped with NIST traceable certificates. Every 743B includes a serial port cable and a DPC/ TRACK Sample, including complimentary upload/export utility software. DPC/TRACK software includes software disks, an instruction manual, a serial port cable, and a DB9 to DB25 (9-pin top 25-pin) adapter. Included with the 744 are two sets of TL224 industrial test leads, two sets of AC test clips, one set of TP220 test probes, BP7235 NiMH battery pack and charger, serial port cable, HART communications cable, DPC/TRACK Sample Version with free PC communication utility software, instruction manual, HART user's manual, NIST traceable certificate and data. Function Measure Sourcing DC Voltage 0.025% rdg % f.s. 0.01% output % f.s. DC Current 0.01% rdg % f.s. 0.01% output % f.s. Resistance 0.05% rdg. + 50mΩ 0.01% output + 40mΩ Frequency 0.05% 0.01% Thermocouples 0.3 C 0.2 C RTDs 0.3 C 0.1 C Pressure To 0.05% f.s., per Pressure Module specs. (see p. 230) Power Supply 741B & 743B: Internal NiCd battery pack, 7.2V, 1700mAh; 744: Internal NiMH battery pack, 3500mAh Battery Life Typically over 8 hours Dimensions 130 x 236 x 61mm (5.1 x 9.3 x 2.4") Weight 1.4 kg (3 lb 1 oz) 741B Documenting Process Calibrator $ B Documenting Process Calibrator $ Documenting Process Calibrator $ BC7217 Battery Charger $ BE9005 Battery Eliminator $ BP7217 NiCd Battery Pack $ BP7235 NiMH Battery Pack $ C700 Hard Carrying Case $ C781 Soft Carrying Case $64.00 C789 Soft Carrying Case $ M1731E 229

9 PROCESS CALIBRATOR Easy to read measure/source screen lets you view input and output simultaneously Measure volts, ma, RTDs, thermocouples, frequency and ohms Source/Simulate volts, ma, thermocouples, RTDs, frequency, ohms and pressure to calibrate transmitters Measure/Source pressure using any of 29 Fluke 700Pxx Pressure Modules Source ma with simultaneous pressure measurement to conduct valve and I/P tests Support flow meter testing with frequency and counts per minute Perform fast linearity tests with auto step and auto ramp Power transmitters during test using loop supply with simultaneous measurement Store frequently-used test set-ups for later use Easy to carry yet stands up to field use Each calibrator includes TL75 Test Leads, AC70 Test Clips, one pair of stackable test leads and user's manual Function (M or S) Range or Type Resolution Accuracy Voltage 0 to 100 mv 0.01 mv 0.02% rdg. + 2 LSD 0 to 10 V (Source) 0.01V 0 to 30 V (Measure) 0.01 V ma 0 to 24 ma ma 0.02% rdg. + 2 LSD mv (TC terminals) mv to mv 0.01 mv 0.025% range + 1 LSD Resistance 15 to 3200Ω 0.01 to 0.1Ω 0.10 to 1.0Ω Frequency 2.0 to 1,000.0 CPM 0.1 CPM ±0.05% 1 to 1100 Hz 1 Hz ±0.05% 1.0 to 10.0 khz 0.1 khz ±0.25% Loop Supply 24 VDC n/a 10% Thermocouples J, K, T, E, L, N, U 0.1 C, 0.1 F to 0.7 C Thermocouples B, R, S 1 C, 1 F to 1.4 C RTDs Ni120 (672), 0.1 C, 0.1 F to 0.2 C Pt100, 200, 500, 1000 (385) Pt100 (3916), Pt100 (3926) Power Supply Four "AA" alkaline batteries Battery Life 25 hours typical Dimensions 96 x 200 x 47 mm (3.8 x 7.9 x 1.9") Weight 650 g (23 oz) 725US Multifunction Process Calibrator $ PRESSURE MODULES 29 pressure module options Ranges from in. H 2 O (0.249 kpa) to 10,000 psi ( MPa) Gauge, differential dual (compound), absolute and vacuum modules Full accuracy performance from 0 to 50 C Pressure readings update twice per second and may be displayed in up to 11 different units Rugged cases protect the modules from harsh environments 230 M1730E 700P00 Pressure Module, 0-1 in H 2 0 Diff $ P01 Pressure Module, 0-10 in H 2 0 Diff $ P02 Pressure Module, 0-1 PSID $ P03 Pressure Module, 0-5 PSID $ P04 Pressure Module, 0-15 PSID $ P05 Pressure Module, 0-30 PSIG $ P06 Pressure Module, PSIG $ P07 Pressure Module, PSIG $ P08 Pressure Module, PSIG $ P09 Pressure Module, 1500 PSIG $ P22 Pressure Module, 0-1 PSID, Wet $ P23 Pressure Module, 0-5 PSID, Wet $ P24 Pressure Module, 0-15 PSID, Wet $ P27 Pressure Module, 300 PSIG, Wet $ P29 Pressure Module, 3000 PSIG, Wet $ P30 Pressure Module, 5000 PSIG, Wet $ P31 Pressure Module, PSIG, Wet $ PA3 Pressure Module, 0-5 PSIA $ PA4 Pressure Module, 0-15 PSIA $ PA5 Pressure Module, 0-30 PSIA $ PA6 Pressure Module, PSIA $ PD2 Pressure Module, ±1 PSID $ PD3 Pressure Module, ± 5 PSID $ PD4 Pressure Module, ± 15 PSID $ PD5 Pressure Module, PSIG $ PD6 Pressure Module, PSIG $ PD7 Pressure Module, PSIG $ PV3 Pressure Module, -5 PSID $ PV4 Pressure Module, -15 PSID $

10 PROCESS CALIBRATORS Features Model 787: Cat III 1000V safety-rated, True RMS multimeter Measure AC and DC voltage, AC and DC current, resistance, continuity and frequency Simultaneous ma and % of scale readout on ma output 25% Manual Step plus Auto Step and Auto Ramp on ma output True RMS AC voltage measurement to 1kHz Frequency measurement to 20kHz Min/Max/Avg/Hold/ Relative modes Diode test and continuity beeper DC current source/loop calibrator 20mA current source/ simulator Clear, 4000-count LCD with backlight Includes: C81Y protective yellow holster with Flex-Stand, TL75 safety-designed test lead set plus alligator clips, one 9V alkaline battery, product overview and users manual (CD-ROM) Features Model 789: 24V loop power supply HART mode setting with loop power (adds 250Ω resistor) 20mA drive into 1200Ω 0-100% ma Span Check buttons to toggle between 4 and 20mA Double-sized, dual display Backlight with two brightness settings Infrared I/O serial port compatible with FlukeView Forms Software Improved battery power with four AA batteries Includes: TL71 premium safety-designed test lead set plus alligator clips, 4 AA alkaline batteries, product overview and users manual (CD-ROM) in 14 languages Accessories: TL71 80i-400 C81Y 80T-IR TL220 Function Range Accuracy DC Voltage 400.0mV, 4.000, 40.00, 400.0, 1000V 0.1% rdg. + 1 LSD AC Voltage (Trms) 400.0mV, 4.000, 40.00, 400.0, 1000V 0.7% rdg. + 2 LSD DC Current 30.00mA 0.05% rdg. + 2 LSD 1.000A (0.440A continuous) 0.2% rdg. + 2 LSD AC Current 1.000A (0.440A continuous) 1% rdg. + 2 LSD Resistance 400.0Ω, 4.000, 40.00, 400.0kΩ, 0.2% rdg. + 1 LSD 4.0, 40MΩ Frequency , Hz, kHz 0.005% rdg. +1 Diode Test 789: 2.000V (shows diode voltage drop) 2% rdg. + 1 LSD 787: 2.400V (shows diode voltage drop) 2% rdg. + 1 LSD Continuity Beeps for resistance < 100Ω Output Function Range Drive Capability Accuracy DC Current Output to mA or 789: 24V or Ω 0.05% span to mA 20mA Over-range to mA 787: 12V or 500Ω 0.05% 20mA DC Current Simulate to mA or 20mA 0.05% span to mA (selectable) Over-range to mA 24V Loop Supply 789: Minimum 24V 20mA > 24V 787: n.a. 80T-150U C25 C100 TL81A 787 Process Calibrator/Multimeter $ Process Calibrator/Multimeter $ T-IR Infrared Temperature Probe $ TK Thermocouple Module $ T-150U Universal Temperature Probe $ i-400 AC/DC Clamp-on Current Probe $ i1010 AC/DC Current Clamp $ C25 Soft Carrying Case $41.00 C100 Hard Carrying Case $48.00 LPAK80-4 Meter Locking Kit $32.00 TPAK Meter Hanging Kit $40.00 TL220 Industrial Test Leads $72.00 TL81A Deluxe Test Lead Set with Case $ M1732E 231

11 PRESSURE CALIBRATORS Model G & 100G Measure pressure and vacuum to 0.05% of full scale with internal 30 psig or 100 psig sensor 1/8 NPT pressure fitting compatible with noncorrosive gases and liquids Measure pressure to 10,000 psi/69 mpa using one of 29 Series 700 Pressure Modules Measure ma with 0.025% accuracy and ma resolution, while sourcing 24V loop power Wide range of selectable measurements units for pressure Min/Max/Hold functions Model US & 100US Built-in pressure/vacuum hand pump, with vernier and bleed valve Pressure and vacuum measurement to 0.05% of full span, using an internal pressure sensor (dry air only) Pressure measurement to 10,000 psi/700 bar using any of the Series 700 Pressure Modules Wide range of selectable measurement units for pressure Measure ma with 0.025% accuracy and ma resolution 24 volt loop power supply 1/8" NPT female pressure fitting Min/Max/Hold functions G Pressure Calibrator $ G Pressure Calibrator $ US Pressure Calibrator $ US Pressure Calibrator $ Series 700 Pressure Modules 29 pressure modules Ranges from 1.000" H 2 O ( kpa) to 10,000 psi ( Mpa) Gauge, differential, dual (compound), absolute and vacuum modules Rugged cases protect the modules from harsh environments Full-accuracy performance from 0 C to 50 C Pressure readings update twice per second, and may be displayed in up to 11 different units Pressure Modules are found on page G G US US Function Range Resolution Accuracy Notes Measure pressure 1-12 to 30 psi psi 0.05% f.s. Dry air only (718), (internal sensor) (-83 to 207 kpa) (0.01 kpa) Zero, Min, Max, Over-pressure 3xFS Hold, Damp Measure pressure 1-12 to 100 psi 0.01 psi 0.05% f.s. Dry air only (718), (internal sensor) (-83 to 690 kpa) (0.1 kpa) Zero, Min, Max, Over-pressure 2xFS Hold, Damp Measure pressure 1 28 Pressure To psi, To 0.05% f.s. Media compatibility (w/ Pressure Modules) Modules, 1.0" per pressure per pressure per Pressure Module Over-pressure per H 2 O/0.25 kpa to module specs module specs specs. Zero, Min, Max, Pressure Module specs 10,000 psi/69 Mpa Hold, Damp Source Pressure, 12 psig to f.s. N/A N/A built-in pump Measure ma 0 to 24 ma ma 0.025% + 1 ct. Loop Supply 24V DC N/A ±10% Drive; 20 ma into 1000Ω for battery > 6.8V; 700Ω for battery 5.8 to 6.8V 1 Supported Pressure Units; psi, in. H 2 O (4 C), in. H 2 O (20 C), cm H 2 O (20 C), bar, mbar, kpa, inhg, mmhg, kg/cm 2 2 Fluke 718 for use with non-corrosive gases. 232 M2087E

12 INFRARED CALIBRATORS This new portable infrared calibrator provides a stable blackbody target for calibrating noncontact infrared thermometers up to 500 C (932 F). This unit features a large, temperature controlled blackbody target with a diameter of 2.25" (57mm), which offers a large field of view area for optical variations in infrared thermo-meters. The emissivity of the isothermal target is set at 0.95 (±0.02%) and the target temperature can be controlled in setpoint increments of 0.1 C. For even higher precision, a well is located directly behind the blackbody surface for contact calibration of the blackbody. This unit is as easy to use as "point and shoot". Simply set the desired blackbody temperature from the front panel control buttons, wait a few minutes for equilibrium, and point the thermometer at the target. The radiated energy from the blackbody is measured by your infrared thermometer. simply compare its reading to the display on the blackbody and record the difference. This new portable infrared calibrator can certify most handheld thermometers in the range of 50 to 500 C, with accuracy to ±0.5 C and stability to ±0.1 C. Short heating and cooling times mean you won't have to wait long to get your work done. From room temperature to 500 C, the 9132 will be stable within 30 minutes. No other infrared calibrator gives you this level of precision in such a compact package. Range: 50 to 500 C (122 to 932 F) Accuracy: ±0.5 C at 100 C (±0.9 F at 212 F); ±0.8 C at 500 C (±1.4 F at 932 F) Stability: ±0.1 C at 100 C (±0.18 F at 212 F) ±0.3 C at 500 C (±0.54 F at 932 F) Resolution: 0.1 Target Size: 2.25" (57mm) Target Emissivity: 0.95 (±0.02 from 8 to 14µm) Heating Time: 30 minutes (50 to 500 C) Cooling Time: 30 minutes (500 to 100 C) Power Supply: 115 VAC ±10%, 3A or 230 VAC ±10%, 1.5A, switchable, 50/60Hz, 340W Dimensions: 4 x 6 x 7" (102 x 152 x 178mm) Weight: 4 lb (1.8 kg) HT Infrared Thermometer Calibrator $ CALIBRATION BATHS These Micro-Baths give you the stability and precision of a liquid bath in a dry-well-sized package. Each model is stable to ±0.03 C or better, depending on the fluid you use. Uniformity is ±0.02 C or better for low uncertainties using a reference thermometer. Display accuracy is ±0.25 C for quick calibrations without a reference thermometer. With a 1.9" diameter, 5.5" deep tank, a Micro-Bath can calibrate any type of sensor including short, square, or odd-shaped sensors. The problems of fit and immersion are virtually eliminated by using a fluid medium rather than a dry block calibrator. Micro- Baths are perfect for liquid-in-glass and bimetal thermometers. Cold Micro-Baths are CFC-free, and also compressor-free. Temperature range and stability are achieved with only one moving part, which means more durability and less weight. All Micro-Baths have RS-232 ports, come with Interface-it software, and can be used with Met/Temp II software. Also included are contacts to calibrate a thermal switch, eight set-point memory storage, ramp-rate adjust, and over-temperature safety cutout. Model HT HT HT Range 35 to 200 C (95 to 392 F) -5 to 125 C (23 to 257 F) -30 to 125 C (-22 to 257 F) Stability ±0.02 C at 100 C; ±0.03 C at 200 C ±0.015 C at -5 C; ±0.03 C at 121 C ±0.03 C at -25 C; ±0.05 C at 125 C (oil 5013) (oil 5010) (oil 5010) Accuracy ±0.25 C Uniformity ±0.02 C Resolution 0.01 C/ F Heating Time 25 to 200 C: 40 minutes 25 to 100 C: 30 minutes 25 to 100 C: 35 minutes Cooling Time 200 to 100 C: 35 minutes 25 to 0 C: 30 minutes 25 to -20 C: 45 minutes Fluid Volume 0.75L 0.75L 1.0L Well Size 2.5" dia. x 5.5" deep (64 x 139 mm) Access opening is 1.9" (48 mm) dia. Power Supply 115VAC, 2.3A or 230VAC, 1.1A 115VAC, 1.8A or 230VAC, 0.9A VAC, 50-60Hz, 400W switchable, 50/60Hz, 270W switchable, 50/60Hz, 200W Dimensions (WHD) 5.5" x 10.4" x 8" 7.2" x 12" x 9.5" 9" x 13.2" x 10.5" (140 x 260 x 200 mm) (180 x 310 x 240 mm) (230 x 340 x 260 mm) Weight 10 lb (4.5 kg) with fluid 15 lb (6.8 kg) with fluid 22 lb (9.8 kg) with fluid Model $ $ $ M1595E 233

13 DRY-WELL CALIBRATORS The Model 9100S Dry-well is perfect for checking RTDs, thermocouples, and small bimetal thermometers in the field. It's simple and convenient, too. Plug it in, switch it on, set the temperature with the front panel buttons, and insert your probe into the properly sized well. Compare the reading of your device to the display temperature or to an external reference, and the difference is the error in your device. It has a range to 375 C (707 F) and a display resolution of 0.1. Accuracy ranges from ±0.25 C to ±0.5 C and stability ranges from ±0.7 C to ±0.3 C, depending on set-point temperature. The Model 9102S is excellent for dial gauges, digital thermometers, bulb switches, and other sensors that need calibration below ambient. It has a temperature range of -10 to 122 C, features display accuracy of ±0.25 C, and is stable to ±0.05 C. The 9102S has two wells so you can use one for a reference thermometer to increase accuracy. Both wells are 1/2" in diameter, and each has inserts for almost any sensor size. The 9102S also has a battery pack option that gives you approximately four hours of field use when AC power is unavailable. Model 9100S HT9102S-156 Range 35 to 375 C (95 to 707 F) -10 to 122 C (14 to 252 F) at 23 C ambient Accuracy ±0.25 C at 50 C; ±0.25 C at 100 C; ±0.5 C at 375 C ±0.25 C Stability ±0.07 C at 50 C; ±0.1 C at 100 C; ±0.3 C at 375 C ±0.05 C Well-to-Well Uniformity ±0.2 C with sensors of similar size at equal depths within wells Heating Times Ambient to 375 C: 9.5 minutes Ambient to 100 C: 10 minutes Stabilization Time 5 minutes 7 minutes Cooling Times 375 C to 100 C: 14 minutes Ambient to 0 C: 10 minutes Well Depth 4" (102mm); 1/16" (1.6mm) hole is 3.5" (89mm) deep 4" (102mm) Power Supply 115VAC, 1.5A or 230VAC, 0.8A, specify, 50/960Hz, 175W VAC, 50/60Hz, 60W; or 12VDC Dimensions 2.25 x 4.9 x 5.9" (57 x 125 x 150mm) 3.9 x 5.5 x 6.9" (99 x 140 x175mm) Weight 2 lb 3 oz (1 kg) 4 lb (1.8 kg) The Model 9100S is available with a choice of four fixed-block options. Block "A" handles a full range of probe sizes with a single well of each size (1/16", 1/8", 1/4", 5/32"; 2 wells of 3/16"). Block "B" features four different size wells (1/8", 3/16", 1/4", 3/8"). Block "C" has two wells, one well is 3/16" in diameter, the other has a diameter of 1/2" and accepts 9102H inserts. Block "D" has three pairs of metric sized wells (3mm, 4mm, 6mm). HT9100S-A-156 Dry-well Calibrator w/ Micro-block A $ HT9100S-B-156 Dry-well Calibrator w/ Micro-block B $ HT9100S-C-156 Dry-well Calibrator w/ Micro-block C $ HT9100S-D-156 Dry-well Calibrator w/ Micro-block D $ C Carrying Case $84.00 Model 9102S features removable insert sleeves 1/2" O.D. x 4" deep (13 mm x 102 mm) and comes complete with 1/4" and 3/16" inserts. Order additional insert sizes as needed. HT9102S-156 Dry-well Calibrator $ Blank Insert $ Insert, 1/16" (1.6 mm) $ Insert, 1/8" (3.2 mm) $ Insert, 3/16" (4.8 mm) $ Insert, 1/4" (6.4 mm) $ HT Insert, 5/16" (7.9 mm) $ Insert, 3/8" (9.5 mm) $ HT Insert, 7/16" (11.1 mm) $ HT Insert, 5/32" (4 mm) $ Battery Pack $ Carrying Case $ M1597E

14 DRY-WELL CALIBRATORS These field dry-wells beat every other dry-well in the industry in performance, size, weight, convenience, ease of calibration, software, and price. In addition, the heating and cooling rate of each of these dry-wells is adjustable from the front panel, thermal switches can be checked for actuation testing, and multiple hole inserts are available for a variety of probe sizes. These dry-wells are also very easy to calibrate. You don't even have to open the case. This means less maintenance costs and less down time when they do need calibration. Interface-it software lets you adjust set points and ramp rates, log dry-well readings to a file, create an electronic strip chart, and perform thermal switch testing with data collection. MODEL 9103 This model covers below-ambient temperatures as low as -25 C. It reaches temperatures 50 C below ambient, so -25 C is reached under normal ambient conditions. The 9103 is stable to ±0.02 C and its display is calibrated to an accuracy of ±0.25 C at all temperatures within its range. 0 C is reached in just 8 minutes, and 100 C is reached in 6 minutes. MODEL 9140 This model has a temperature range of 35 to 350 C, and it reaches it maximum temperature in 12 minutes. The unit has a stability of ±0.05 C or better and a uniformity of at least 0.4 C in the largest diameter wells and 0.1 C in the smaller wells. Use the display, calibrated to ±0.5 C, as your reference, or use an external thermometer for maximum calibration accuracy. MODEL 9141 This upright unit does calibrations up to 650 C and heats up in only 12 minutes. You can control all functions from the front panel or hook it up to your PC with its built-in RS-232 port. Interchangeable Insert Options Four removable well inserts are available. Insert "A" handles a full range of probe sizes with a single well of each size (1/16", 1/8", 3/16", 1/4", 3/8", 1/2"). Insert "B" features two wells each of 3/8", 1/4" and 3/16" in diameter for doing comparison calibrations. Insert "C" has six 1/4" diameter wells for multiple probe calibrations. Insert "D" has three pairs of metric sized wells (3mm, 4mm, 6mm) X Dry-well Calibrator $ Blank Insert $ Insert A $ Insert B $ Insert C $ Insert D $ X Dry-well Calibrator $ Blank Insert $ Insert A $ Insert B $ Insert C $ Insert D $ X Dry-well Calibrator $ Blank Insert $ Insert A $ Insert B $ Insert C $ Insert D $ Specify insert X, X = A, B, C or D included insert Model Range -25 to 140 C (-13 to 284 F) at 23 C ambient 35 to 350 C (95 to 662 F) 50 to 650 C (122 to 1202 F) Accuracy ±0.25 C ±0.5 C (holes > 1/4": ±1 C) ±0.5 C to 400 C; ±1.0 C to 650 C (holes > 1/4": ±2 C) Stability ±0.02 C at -25 C; ±0.04 C at 140 C ±0.03 C at 50 C; ±0.05 C at 350 C ±0.05 C at 100 C; ±0.12 C at 500 C ±0.12 C at 650 C Uniformity ±0.1 C between similarly sized wells ±0.1 C with similarly sized wells ±0.1 C < 400 C, ±0.5 C > 400 C with similarly sized wells Heating Times 18 minutes from ambient to 140 C 12 minutes from ambient to 350 C 12 minutes from ambient to 650 C Cooling Times 20 minutes from ambient to -25 C 15 minutes from 350 C to 100 C Stabilization Time 7 minutes Immersion Depth 4.875" (124mm) Insert O.D. 1.25" dia. x 4.88" long (31.8 x 124mm) 1.12" dia. x 4.88 long (28.5 x 124mm) Power Supply 115VAC, 1.3A or 230VAC, 0.7A 115VAC, 4.4A or 230VAC, 2.2A 115VAC, 8.8A or 230VAC, 4.4A switchable, 50/60Hz, 150W switchable, 50/60Hz, 500W switchable, 50/60Hz, 1000W Dimensions (WHD) 5.6" x 10.25" x 9.6" 6" x 3.375" x 7.75" 4.3" x 9.3" x 7.3" (143 x 261 x 245 mm) (152 x 86 x 197 mm) (109 x 236 x 185 mm) Weight 12 lb (5.7 kg) 6 lb (2.7 kg) 8 lb (3.6 kg) M1596E 235

15 PROCESS LABORATORY CALIBRATORS Superior calibration accuracy to % of reading Direct keyborad entry or cursor entry with decade control Automatic standby function protects device under test Both mdoels source current and voltage Read thermocouple, RTD and pressure (M2001 only) Source/Read 11 thermocouple types (M2001 only) Source/Read 19 standard RTD types (M2001 only) Custom RTD/SPRT profile (M2001 only) Nine setpoints for each output range and type Auto step and dwell Local or RS232 remote control Function Output Range Input Range 4 Resolution Accuracy 1 Voltage 0 to mV n/a 1µV ±0.003% (30ppm) ± 3µV 0 to V n/a 10µV ±0.003% (30ppm) ± 20µV 0 to V n/a 100µV ±0.003% (30ppm) ± 200µV 0 to V n/a 1mV ±0.003% (30ppm) ± 2mV Current 0 to mA n/a 1µA ±0.1% ±2 counts MODEL M2001 ONLY Thermocouple J, K, T, E, R, S, N, B, L, U, C J, K, T, E, R, S, N, B, L, U, C 0.1 C/ F ±0.14 C; type J typical & mv & mv RTD Pt385 (100, 200, 500, 1000), Pt385 (100, 200, 500, 1000), 0.1 C/ F; Pt ±0.1 C; Pt Pt392, Pt3916 (JIS), Ni120, Pt392, Pt3916 (JIS), Ni120, C/ F; Pt ±0.020 C; Pt Cu10, YSI400 Cu10, YSI400, 25Ω SPRT Ohms 5 to Ω n/a 0.01Ω ±0.03Ω 5 to Ω n/a 0.1Ω ±0.3Ω n/a 0 to Ω 0.001Ω 40ppm ±0.002Ω n/a 0 to Ω 0.01Ω 40ppm ±0.02Ω Pressure n/a 0 to 1 H 2 O; to 10,000 psi Module dependent ±0.025% f.s. typical 1 Accuracy specs are % rdg. unless otherwise noted 2 RTD output accuracy and resolution 3 RTD input accuracy and resolution 4 All RTD/Ω input are 4-wire Stability: Warm-up Time: Display: Power Supply: Dimensions: Weight: 10% of accuracy spec/ C 30 minutes to rated accuracy 16 x 2 large character alphanumeric LCD, backlit 90 to 240 VAC; < 15 VA 11.5 x 4.7 x 8.75 (292 x 119 x 220mm) 5 lb (2.27kg) M2000 Bench Calibrator $ M2000A Bench Calibrator w/ IEEE-488 Interface $ M2001 Lab Process Calibrator $ M2001A Lab Process Calibrator w/ IEEE-488 Interface $ M2000/1RMK Rack/Panel Mount Kit $ IBP-1 Pt100 High Accuracy Probe $ LCA-1 Low Thermal RTD Lemo Connector $ JKTE Thermocouple Kit $ RSNB Thermocouple Kit $ URA-1 Universal RTD/Ω Adapter $ M1743E