EXPERT 24 CUTTING PLOTTER User Manual
|
|
- Maria Moore
- 5 years ago
- Views:
Transcription
1 EXPERT 24 CUTTING PLOTTER User Manual ` Great Computer Corporation
2 NOTICE GCC reserves the right to modify the information contained in this user manual at any time without prior notice; un-authorised modification, copying distribution or display is prohibited. All comments, queries or suggestions concerning this manual please consult with your local dealer.
3 Expert 24 user manual Important Information Thank you for purchasing the Expert 24 Cutting Plotter. Before you use the cutting plotter, please make sure that you have read the safety precautions and instructions below.! Caution SAFETY PRECAUTIONS! For safety concern, please always hold the cutter firmly from the bottom while moving it. Do not move the cutter by clasping the depression area on both sides. O (correct) X (Incorrect) Do not shake or drop the blade holder, a blade tip can fly out. During an operation, do not touch any of the moving parts of this machine (such as the carriage). Also be careful to make sure that clothing and hair do not get caught. Always connect the power cable to a grounded outlet. Always use the accessory power cable which is provided. Do not wire the power cable so that it becomes bent or caught between objects. Do not connect the power cable to branching outlet to which other machines are also connected, or use an extension cable. There is danger of overheating and of mis-operation of the machine. Keep the tools away from children where they can reach. Always put the pinch rollers within the white marks. Important Information
4 Important Information Table of Contents Expert 24 user manual 1. General Information 1.1 Package Items Product Features The Appearance Installation 2.1 Precaution Stand & Flexible Media Support System Blade Installation Media Loading Cable Connections USB Interface How to switch the USB mode RS-232 Interface Operation 3.1 The Control Panel VLCD File Uploader Data Transmission Basic Maintenance 4.1 Cleaning the cutting Plotter Cleaning the Grid Drum Cleaning the Pinch Rollers Trouble Shooting 5.1 What if Expert 24 cannot Operate? Light Indicators Cutting Quality Problems 5-4 Appendix A-1 CorelDraw instruction A-1 A-2 Expert 24 Specification A-2 A-3 Blade Specification A-3 Table of Contents
5 1. General Information Expert 24 user manual 1.1 Package Items The package of Expert 24 contents the items listed below, please check carefully. If you find any item missing, please consult your local dealer for further assistance. Item Quantity Cutting Plotter 1 Set Accessories 1 Set 1. Installation CD 2. AC Power Cord 3. Desktop Support Brackets 4. Cutting Pad 5. USB Cable 6. RS-232 Cable 7. Tweezers 8. Paper Slicer 1.2 Product Features The followings are the main features of the Expert 24 cutting plotters: Dual-port connectivity USB & Serial interface. Up to 250 gram cutting force. Up to 400 mm/per second cutting speed. General Information 1-1
6 Expert 24 user manual 1.3 The Appearance (EX-24) The Front View A B C D E Figure 1-1 F G H Object Description A Primary Pinch Roller To help hold the media during cutting. B Slicing Groove To help slice off media. C Alignment Ruler To align media with clear guideline marks D Tool Carriage To help perform cutting job with installed blade or pen. E Blade Holder To hold the blade. F Platen The surface for holding and supporting media in operation. G Cutting Pad To protect blade and plate in operation. H Control Panel To consist of 10 control keys and 6 LED lights The Back View J Figure 1-2 Object Description J Grid Drum To move media back and forth in operation. General Information 1-2
7 Expert 24 user manual The Side Views K L M Figure 1-3 N O Figure 1-4 Object Description K AC Power Connector To insert the AC power cord. L Fuse 3Amp. M Power Switch To turn on or off the machine. N USB Connector To connect the machine and a computer through a USB cable. O Serial Interface Connector To connect the machine and a computer through a RS-232 cable. General Information 1-3
8 Expert 24 User Manual 2. Installation 2.1 Precaution Please read below information carefully before you start installation. Notice 1 Make sure the power switch is off before installing the cutting plotter. Carefully handle the cutter to prevent any injuries. Notice 2 Choosing a proper place before setting up the cutting plotter Before installing your cutting plotter, select a suitable location, which meets the following conditions. The machine can be approached easily from any direction. Keep enough space for the machine, accessories and supplies. Keep the working area stable, avoiding severe vibration. Keep the temperature between 15 and 30 (60-86 o F) in the workshop. Keep the relative humidity between 25% and 75% in the workshop. Protecting the machine from dust and strong air current. Preventing the machine from direct sunlight or extremely bright lighting. Notice 3 Connecting the Power Supply Check the plug of the power cord to see if it mates with the wall outlet. If not, please contact your dealer. Insert the plug (male) into a grounded power outlet. Insert the other end (female) of power cord into the AC connector of cutting plotter. Installation 2-1
9 Expert 24 User Manual 2.2 Stand Stand Installation Please follow the procedures below for assembling the stand and the media support system. Step 1 Please examine the supplied items in the accessory box of the stand carton before you install: Stand is an optional item for Expert 24, Item List: 1 Left side vertical stand 1 Right side vertical stand 1 Support for left side 1 Support for right side 1 Stand Beam 2 Bottom Stands with wheels 2 Sliding brackets for paper take up 1 Hex Wrench (M5)Φ4 28 Socket flat head screws(m6*12l) 1 Installation Guide Step 2 Position the Left side vertical stand perpendicularly to part and put the screws into the holes and tighten them to form a left side T-stand (Figure 2-1). Repeat the same steps with the Right side vertical stand. Left side vertical stand Bottom Stand Figure 2-1 Installation 2-2
10 Expert 24 User Manual Step 3 Place the stand beam upright on the T-stand and put the screws into the holes but do not tighten them at this step. Stand Beam T-stand Figure 2-2 Step 4 Position both the left Support and right Support perpendicularly to the T-stand and put the screws into the holes and tighten them as shown in Figure 2-3. Support for left side Support for right side Figure 2-3 Installation 2-3
11 Expert 24 User Manual Step 5 Remove the cutting plotter from the carton. Position the stand under the plotter, and insert the screws into the holes on the bottom of the plotter but do not tighten them up as shown in Figure 2-4. Figure 2-4 Step 6 Tighten the screws of step 3 and step 5. Place the sliding brackets for paper takeup onto the stand beam. sliding brackets for paper takeup Figure 2-5 Installation 2-4
12 2.3 Blade Installation Figure 2-6 is the illustrator of the blade holder. Insert a blade into the bottom of the blade holder and remove the blade by pushing the pin. Make sure that your fingers are away from the blade tip. Adjustment depth knob Outward ring Expert 24 User Manual Pin Step 1 Step 2 Figure 2-6 Install blade (Figure 2-7). Push the blade to the bottom of the blade holder (Figure 2-8). Figure 2-7 Figure 2-8 Step 3 Adjust the blade tip to suitable length by screwing Blade tip adjustment screw clockwise or count-clockwise. (Figure 2-9). Figure 2-9 Tips: The proper length means the blade s length is adjusted 0.1mm more than film s thickness. That is, if the thickness of film is 0.5mm, then blade s length is properly adjusted 0.6mm and it can completely cut through the film layer yet avoid penetrating the backing. Installation 2-5
13 Expert 24 User Manual Step 4 Insert the blade holder into tool carriage. Please note the outward ring of the holder must put into the grooves of carriage firmly (see Figure 2-10), fasten the case (Figure 2-11). Figure 2-10 Figure 2-11 Step 5 Use the reversing steps to remove the blade holder. Step 6 Eject the blade: Push Blade eject pin to eject blade when the blade needs to be replaced. Caution The blade will lose its sharpness after a period of usage, the cutting quality m be affected. By increasing the cutting force, it might do the trick. However, the blade is worn out and no longer provides a reliable cutting, you should rep a new one. The blade is consumable and must be replaced as often as neces to maintain the cutting quality. The quality of the blade deeply affects cu quality. So be sure to use a high quality blade to ensure good cutting results. Tips - When to replace a new blade: If the blade is broken, you have to replace a new one. If cutting quality is not as good as usual, you may need to replace a new one. If the material cannot be cut through by higher cutting force, you may need to replace a new one. Installation 2-6
14 2.4 Media Loading Expert 24 User Manual Loading the Sheet Media To load the media properly, please follow the below procedures: Step 1 Lift the 2 levers at the back side of cutter to raise pinch rollers (Figure 2-12). Figure 2-12 Step 2 Load your media on the platen and slide it under the pinch rollers from either the front side or the backside. The alignment rulers on the platen extension will help you to adjust the media precisely (Figure 2-13). Figure 2-13 Step 3 Then move the pinch rollers manually to the proper position. Be sure the pinch rollers must be positioned above the grid drum. The white marks on the main beam will remind you where the grid drums are (Figure 2-14). White mark Figure 2-14 Figure 2-15 Installation 2-7
15 Expert 24 User Manual CAUTION!!! Make sure the Primary and secondary pinch rollers are set to right positions. Position the Primary Pinch Rollers at the right and left sides of media. Position the Secondary Pinch Roller at the center of media. (O) Correct Figure 2-16 Secondary Pinch Roller Primary Pinch Roller (X) Incorrect Figure 2-17 Step 4 Push the lever backward to lower down the pinch rollers (Figure 2-15). Step 5 After turn on the power, the tool carriage will measure the size of the media automatically. And the plotting cutter begins to work. Installation 2-8
16 Expert 24 User Manual Note: Always adjust the position with the pinch rollers raised. Please reposition the pinch roller by holding the center of the pinch roller and moving it from the rear end of the machine. (Figure 2-18) DO NOT move the pinch roller by holding its front rubber roller (Figure 2-19). Figure 2-18 Figure 2-19 (O) Correct (X) Incorrect Loading the Roll Media You can use the stand with flexible media support system. Please refer to Chapter 2.2 for hardware setup, and Chapter for media loading. 2.5 Cable Connection The cutting plotter communicates with a computer through a USB (Universal Serial Bus) or a Serial port (RS-232C). This chapter shows you how to connect the cutting plotter to a host computer and how to set up the computer/cutting plotter interconnection.!! Notice: When USB connection is enabled, serial port will be disabled automatically. Installation 2-9
17 Expert 24 User Manual USB Interface Expert 24 build-in USB interface are based on the Universal Serial Bus Specifications Revision 1.1. (Operation system of Windows 95, Windows NT don t support USB ). USB driver installation Caution!! If you are using Windows 2000 / XP / Vista / 7 as your operating system, make sure you log in using the Administrator account. Use the USB One-click Installation for quick driver installation. Follow the simple steps below for driver setup. Step 1: Connecting your GCC cutter 1. Connect the USB connector to the machine and then USB driver will installed automatically. NOTE Check that the USB mode option is set to Common USB Mode before running the installation. Step 2: Installing the software (1) Put the installation CD into your CD-ROM. Please make sure that the USB device is connected before you start the driver installation. Installation 2-10
18 Expert 24 User Manual (2) Choose the model you want to install from the driver list and click on either the 32 bit or 64 bit driver installation depending on the operating system installed on your computer to start the installation. (The Expert Pro model is used as an illustration in the following steps.) NOTE If you use the Windows 7 / Vista 64 bit program, please note that a pop-up window will be shown upon the initial installation as shown below: Click Yes to continue. Installation 2-11
19 Expert 24 User Manual (3) Click Next (4) The installation will take a few minutes to complete and you will see a message below and click on OK upon completion. Enjoy your GCC cutter! Note: (1) If the driver is being installed for a second time, the user will be prompted as to whether a second copy of the driver installation is required. (2) If the user selects yes, a second copy of the driver will be installed. Installation 2-12
20 Expert 24 User Manual How to switch the USB mode? Step 1. Press ON/ Offline button to switch to the offline status. Step 2. Press Pause and Origin Set button at the same time and you will find the current status of the USB mode indicated by the three LEDs as shown below. Flashing LED on Operation System Repeat Data Clear Cut Test Common USB Mode GCC USB Mode A. Switching to GCC USB mode If you want to switch the USB mode from Common USB mode to GCC USB mode, please press the Data Clear button and then press the origin set button to finish your set up. B. Switching to Common USB mode If you want to switch the USB mode from GCC USB mode to Common USB mode, please press the Cut Test button and then press the origin set button to finish your set up. Step 3. Please re-connect the U SB cable and complete the installation RS-232 Interface Connecting to the RS-232 (Serial) Port 1. For IBM PC, PS/2 users or compatibles, connect the RS-232C cable to the serial connector of the assigned serial port (COM1 or COM2) of your host computer. 2. Set up the communication parameters (Baud Rate and Data Bits/Parity) to match the setting of software package, refer to chapter 3 Misc key description. Installation 2-13
21 Expert 24 user manual 3. Operation 3.1 The Control Panel The Outline of control panel Figure 3-1 Key Function POWER LED To indicate the power status ( light up: power on; light off: power off ) ERROR LED To indicate the error status ( light up: error; light off: normal ) To switch modes or stop cutting job( light up: on-line; light off: off-line ) ON/OFF LINE While in on-line mode: only ON/OFF LINE and PAUSE keys activated While in off-line mode: the settings in VLCD can be adjusted. PAUSE REPEAT DATA CLEAR CUT TEST ORIGIN SET To temporarily halt cutting process or to continue To repeat last job. To clear up buffer memory. To perform cutting tests in different ways. To reset origin at a new position. 4 Arrow Keys To move carriage position, select function, or change setting Reset Origin Note: Make sure the machine is in off-line mode to enable this function. Step 1 Move the carriage to a new position. Step 2 Press the ORIGIN SET button to reset origin. Operation 3-1
22 Expert 24 user manual Cut Test Note: Make sure the machine is in off-line mode to enable this function. It s recommended to keep performing this function until the cutting quality meets your demand before executing the cutting job. Step 1 After sizing, press the ON/OFF LINE button to set as off-line mode. Step 2 Move the carriage to a preferred position. Step 3 Press CUT TEST button to perform Repeat Note: Make sure the machine is in off-line mode to enable this function. Step 1 Press the ON/OFF LINE button to set as off-line mode. Step 2 Press the REPEAT button to perform re-plot function starting at the position where the carriage locates. It is also available to move carriage to a preferred position, re-set origin, and then perform this function. 3.2 VLCD VLCD is a computer program to help modify parameters of cutting functions Installation Step 1 Copy the VLCD.exe file in the Accessories folder of the Expert 24 Installation CD onto your local drive to finish installation. Step 2 Launch VLCD by double-click on the icon. Note: Make sure the machine is in on-line mode to enable this program. There is media in the machine. Operation 3-2
23 Expert 24 user manual Step 3 Choose the right port connected to your computer (Figure 3-2). If you are using the USB cable, choose USB0 from the pull down menu. If you are using a Serial cable, choose either COM1 or COM2. Make sure no other devices are occupying the port that you are going to use. Step 4 Press the Connect button to connect your computer and the cutter. If the connection succeeds, the model info, firmware version, and adjustable parameter columns will be showing (Figure 3-3). (The Expert 24 LX is used as an illustration.) Figure 3-2 Figure Functions of VLCD Below are the functions adjustable in VLCD for Expert 24. Poll Size Force Media Weight Offset Auto Unroll Update Setting Poll Size Click on the Poll Size button will reveal the X/Y values. Operation 3-3
24 Expert 24 user manual In the case, the maximum plotting length is 25000mm, and the distance between the farthest two pinch rollers is mm (Figure 3-4). Figure 3-4 Force To adjust the blade force between 0 and 250 (Default = 50). Media Weight To choose different weights of media in two options: Heavy, and Light (Default). Offset To adjust the blade offset to ensure cutting quality in 8 options: 0.000, (Default), 0.250, 0.275, 0.300, 0.500, 0.750, and Auto Unroll To switch options for sheet media (Auto Unroll Off: Default) and roll media (Auto Unroll On). Update Setting To apply the changed setting onto the cutter by press the Update Setting button. Operation 3-4
25 Expert 24 user manual 3.3 File Uploader Installation File Uploader is a tool to help loading files for direct output. The program ONLY supports HPGL format-files generated via GCC Cutter driver. Copy the GCC File Uploader.exe file in the Accessories folder of the Expert 24 s Installation CD onto your local drive to finish installation. Launch GCC File Uploader by double-click on the icon (Figure 3-5). Figure 3-5 Figure Functions of File Uploader Port setup This function will be activated while choosing COM port for data transmission. Press the Port setup button to pop up the setup window for parameter change (Figure 3-6). Repeat Activate this function by click on the Repeat s checkbox. Repeat Delay the pause time between jobs; Unit: second. Repeat Counts the number of repeat jobs. Operation 3-5
26 Expert 24 user manual 3.4 Data Transmission There are two options to transmit the data from the computer to the cutting plotter: Option 1: With proper interface settings, the data can be transmitted from your application software package to the cutting plotters directly. Option 2: Most cutting software packages are able to emulate HP-GL or HP-GL/2 commands, therefore. As long as the file is HP-GL or HP-GL/2 format, the cutting plotter can output the data precisely. Operation 3-6
27 Expert 24 user manual 4. Basic Maintenance This chapter explains the basic maintenance (i.e. cleaning the cutting plotter) required for the cutting plotter. Except 24 for the steps mentioned below, all the other maintenances must be performed by a qualified service technician. 4.1 Cleaning the cutting plotter In order to keep the cutting plotter under good conditions and have the best performance, you need to clean the machine properly and regularly. Precaution in Cleaning Unplug the cutting plotter before cleaning. Never use solvents, abrasive cleaners or strong detergents for cleaning. They may damage the surface of the cutting plotter and the moving parts. Recommended Methods Gently wipe the cutting plotter surface with a lint-free cloth. If necessary, clean it with a water-rinsed or an alcohol-rinsed cloth. Wipe the cutting plotter to remove any residues on the cutting plotter. Finally absorb water with a soft, lint-free cloth. Wipe all the dust and dirt from the tool carriage rail. Use a vacuum cleaner to clean any accumulated dirt and media residue beneath the pinch roller housing. Clean the platen, paper sensors and the pinch rollers with a water-rinsed cloth or alcohol-rinsed cloth. Finally absorb water with a soft, lint-free cloth. Use the same method mentioned above to clean dust and dirt from the stand. 4.2 Cleaning the Grid Drum Turn off the cutting plotter, and move the tool carriage away from the area needed to be cleaned. Raise the pinch rollers and move them away from the grid drum for cleaning. Use a bristle (a toothbrush is also acceptable) to remove dust from the drum surface. It needs to rotate the drum manually to clean the drum completely (Figure 4-1). Basic Maintenance 4-1
28 Expert 24 user manual Figure Cleaning the Pinch Rollers If the pinch rollers need a thorough cleaning, use a lint-free cloth or cotton swab to wipe away the accumulated dust from the rubber portion of the pinch rollers. To prevent the pinch rollers from rotating while cleaning, use your fingers to hold the pinch rollers in place. Use a lint-free cloth or cotton swab rinsed with alcohol to remove the embedded or persistent dust. Basic Maintenance 4-2
29 Expert 24 user manual 5. Trouble Shooting This chapter helps you to correct some common problems you may come across. Prior to getting into the details of this chapter, please be sure that your application environment is compatible with the cutting plotter. Note: Before contacting your local dealer, please make sure that the problems are coming from your cutting plotter, not from the communication between the computer and cutting plotter or from a malfunction in your computer or software. Why doesn t the cutting plotter operate? 5.1 What if Expert 24 cannot operate? If your cutting plotter doesn t plot, please check the following items first: Is the power cord plugged in properly? Is the power cord connected to the power connector properly? Is the power switch turned on properly? Solutions: If the POWER LED lights on, the cutting plotter should be in a normal condition. Turn off the cutting plotter and turn it on again to see if the problem still exists. If the POWER LED doesn t light, please call your local dealer to resolve this problem. 5.2 Light Indicators Some of the operating problems can be identified by the lights on the control panel. When your cutting plotter stops operating or the lights are on or flashing unexpectedly, see the following descriptions of the panel light patterns and the actions you should take. Trouble Shooting 5-1
30 Expert 24 user manual Warning Indicators When the ERROR LED flashes (as shown below), take the necessary actions according to the following instructions. When the problems are solved, the ERROR LED will turn off automatically. Pressing the ON/OFF LINE button can also turn off the ERROR LED. Warning Indicators ERROR ON/OFF LINE REPEAT DATA CLEAR CUT TEST 1 Graph was clipped 2 HPGL/2 command Error 3 Lever up or no media 4 Cannot repeat 5 Communication error 6 Width sensor error 7 Check media, drum or X motor = flash = on = off Warning 1 The graph is clipped This condition indicates that the cutting graph is bigger than the cutting area. You can solve the problem by: 1. Reload a wider or longer media. 2. Move the pinch rollers to widen the cutting area. 3. Re-scale the graph to a smaller size. Then send the cutting job again from your computer to the cutting plotter. Warning 2 HPGL/2 command error If the cutting plotter cannot recognize the commands from your computer, please check the commands applied to your cutting plotter in the HP-GL/2 or HPGL commands. Then send the same job to the cutting plotter again. If that doesn t solve the problem, please contact your local dealer. Warning 3 Lever up or no media Check that you have lowered the lever down and make sure that you load the media before cutting. Trouble Shooting 5-2
31 Expert 24 user manual Warning 4 Cannot repeat cutting There are two possibilities: 1. There is no data in the buffer: please send the job again from your computer; 2. The buffer is full: please send the same job from your computer again. Under both conditions, press the ON/OFF LINE key to clear the warning message. Warning 5 Communication error Check that the serial/usb/parallel cable has been connected to the cutting plotter and computer properly. If so, then check whether the interface settings are correct. Check that the communication settings in your PC are the same as the ones on your cutting plotter (for example 9600bps, no parity, 8 bits, 1 stop bit). Then, press ON/OFF Line key to switch back to On Line mode. Warning 6 Width sensor error Check that the pinch rollers are positioned above the grid drum and reload the media again. Note: In order to identify the warning messages easily, please stick the warning sticker (in accessory box) on the side cover of your cutting plotter Error Indicators If some mechanical problems occur during the operation, the ERROR LED will turn on. Please follow the instructions below to solve the problem. If the cutting plotter still cannot work, please contact your local dealer and tell him or her about the error indicator. Error Indicators ERROR ON/OFF LINE REPEAT DATA CLEAR CUT TEST 1 SRAM error 2 DRAM error 3 Check media, drum, or X motor 4 Check media or Y motor = flash = on = off Error 1 and 2 Please contact your local dealer to replace SRAM or DRAM. Trouble Shooting 5-3
32 Expert 24 user manual Error 3 Check the media, drum or X-motor (Drum driven motor) This message indicates that there might be a problem on the X-axis. Please check that the drums are working normally and see that the media is well loaded. Then turn on the power and reboot the cutting plotter. Error 4 Check the media, or Y motor (carriage driven motor) This message indicates that there might be an obstruction to the carriage relating to a problem on the Y-axis. Please clear the obstruction and check that the carriage can move smoothly. Then turn on the power and reboot the cutting plotter. 5.3 Cutting Quality Problems Check pen installed correctly and the blade holder fastened securely No Yes Please refer to Chpater 2. Is the blade broken? No Yes Check tool force setting No Replace a new blade Yes Please refer to 3.23 " Cutting Test" to adjust the tool force. Is there any dirt adhered to the blade No Yes Remove the blade and clean it Please contact customer service persionnel for technical support Trouble Shooting 5-4
33 Expert 24 User Manual CorelDRAW Output Instruction The following is an example of how to output the file with CorelDRAW. User Instructions 1. Open CorelDRAW, finish editing all the files you wish to plot and select all the images at once. 2. Select Outline Pen to adjust the outline for cutting. 3. Adjust the value of pen width to mm and click OK to save your input. CorelDRAW Plug-In A-1
34 Expert 24 User Manual 4. Select File Print to output the file to your cutters. 5. Choose the correct model you have installed. CorelDRAW Plug-In A-1
35 Expert 24 User Manual 6. Choose the Layout page and click the Reposition images to: Bottom left corner. Please note that you must put your image at the bottom left corner. 7. Go back to the General page and check that your image is at the bottom left corner. Click Print and get a wonderful cutting image. CorelDRAW Plug-In A-1
36 Expert 24 Specification Expert 24 user manual Model EX-24 Max. Cutting Width 600mm (23.6") Max. Media Width 719mm (28.3") Material Thickness 0.8mm Max. Cutting Force 250g Max. Cutting Speed(Diagonal) 400 mm /sec(15.7"/sec) Software Resolution mm Repeatability ±0.1mm Re-plot Memory 500 Kbyte Interfaces USB & RS-232 Commands HP-GL, HP-GL/2 Configurable Origin Yes Control Panel 6 LEDs/10 Keys Stand Optional Operation Temperature 15 C~30 C / 60 F~86 F Environment Humidity 25% ~ 75% Compatible with Windows 2000/XP/7. The specification and data sheet may vary with different materials used. In order to obtain the best output quality, please maintain the machine regularly and properly. GCC reserves the right to change the specifications at any time without notice. Specification A-2
37 Expert 24 User Manual Blade Specification G For cutting thick fluorescent and reflective vinyl. Also for cutting detailed work in standard vinyl. The blade is 45 with Red Cap(5-unit package), 0.25 mm offset G For cutting reflective vinyl, cardboard, sandblast, flock, and stencil sharp edge. The blade is 60 with Green Cap, 0.50 mm blade offset G For cutting thin sandblast mask and stencil with friction feed or sprocket feed machine. The blade is 60 with Blue Cap, 0.25 mm blade offset G For Cutting small text and fine detail. Sharp blade with smallest offset. The blade is mm blade offset with Black Cap Blade Specification A-3
38 Expert 24 User Manual About the Tool A generic term referring to the blade that cuts the sheet, the pen that does plotting, and the LED bombsight (option) used for pointing to the reference point. OFFSET is the distance that the blade tip is displaced from the centerline of the blade. Blade Blade tip Central line offset Protrusion Length of the Blade Protrusion length of the blade Thickness of the media (t1) Thickness of the base paper (t 2) Length of protrusion = t1 + t 2/ 2, but for your convenience you may just make it about 0.3mm ~ 0.5mm beyond the blade holder tip. Blade Specification A-3
EXPERT 24 CUTTING PLOTTER User Manual
EXPERT 24 CUTTING PLOTTER User Manual ` Great Computer Corporation V.12 2014 Jun. NOTICE GCC reserves the right to modify the information contained in this user manual at any time without prior notice;
More informationEXPERT 52 LX CUTTING PLOTTER User Manual
EXPERT 52 LX CUTTING PLOTTER User Manual ` Great Computer Corporation V.6 2014 Mar. NOTICE GCC reserves the right to modify the information contained in this user manual at any time without prior notice;
More informationLYNX. SIGNWarehouse com. User's Guide. lynx_man_rev1_0504
LYNX User's Guide SIGNWarehouse com lynx_man_rev1_0504 Table of Contents 1. Learning 1.1 Initial Inspection 1-1 1.2 Front View of Lynx 1-2 1.3 Back View of Lynx 1-2 1.4 Side View of Lynx 1-4 2. Installation
More informationEXPERT II Series User Manual
EXPERT II Series User Manual ` http://www.gccworld.com V.7 2017 Jun. NOTICE GCC reserves the right to modify the information contained in this user manual at any time without prior notice; un-authorized
More informationUser Manual. https://www.signwarehouse.com/blog-support/ NOTICE
User Manual https://www.signwarehouse.com/blog-support/ NOTICE SignWarehouse Inc. reserves the right to modify the information contained in this user manual at any time without prior notice; un-authorized
More informationExpert Pro Series User Manual
Expert Pro Series User Manual http://www.gccworld.com V.16 2015 Jul NOTICE GCC reserves the right to modify the information contained in this user manual at any time without prior notice; un-authorized
More informationJaguar IV Series User Manual
Jaguar IV Series User Manual http://www.gccworld.com V.2.4 Apr. 08 NOTICE GCC reserves the right to modify the information contained in this user manual at any time without prior notice; un-authorized
More informationMONARCH 9416 XL QUICK REFERENCE
MONARCH 9416 XL QUICK REFERENCE This Quick Reference contains ribbon loading, supply loading, and general care, maintenance, and troubleshooting procedures for the 9416 XL Thermal Direct and 9416 XL Thermal
More informationUser Manual. https://www.signwarehouse.com/blog-support/ NOTICE
User Manual https://www.signwarehouse.com/blog-support/ NOTICE SignWarehouse Inc. reserves the right to modify the information contained in this user manual at any time without prior notice; un-authorized
More informationTT230SM THERMAL TRANSFER PRINTER USER S MANUAL
TT230SM THERMAL TRANSFER PRINTER USER S MANUAL Operations Overview Unpacking and Inspection This printer has been specially packaged to withstand damage during shipping. Please carefully inspect the packaging
More informationFC7000 Quick Manual E-1 FC7000-UM-8M2
FC7000 Quick Manual FC7000-UM-8M2 Thank you for choosing an FC7000 Series cutting plotter. To ensure the safe and correct use of your cutting plotter and to fully understand and make optimum use of its
More informationRemoval and Installation8
8 Screw Types 8-4 Top Cover Assembly 8-5 Left Hand Cover 8-6 Right Hand Cover 8-10 Front Panel Assembly 8-14 Left Rear Cover 8-15 Right Rear Cover 8-16 Extension Cover (60" Model only) 8-17 Media Lever
More informationAuto-Cutter (JM98901) User's Manual
Auto-Cutter (JM98901) User's Manual -2- Contents Notice 3 SAFETY SIGNS that must be strictly observed! 5 1. Function 7 2. Main specifications of auto-cutter 7 3. Checking items inside the accessory box
More informationMX-8000 User Manual MX Rev
MX-8000 Rev. 070202 Greeting Thank you for purchasing PAITEC USA products. This manual is prepared to provide guidelines on how to properly operate and maintain MX-8000. Copyright Any of the contents should
More informationQuick Start Guide Ioline StudioJet
Quick Start Guide Ioline StudioJet User Notice Trademarks Ioline StudioJet is a trademark of Ioline Corporation. HP is a trademark of the Hewlett-Packard Company. Other product names, logos, designs, titles,
More information1 Contents Welcome... 3 Cutter Parts... 4 Front View... 4 Detail of Carriage Arm... 5 Right Side View... 6 Left Side View... 7 Back View... 8 Detail of Pinch Roller (Back View)... 9 Control Panel... 10
More informationUSER MANUAL. Sign Cutting Plotter VC-600 VC-1300 VC Read This Manual Before Using The Plotter.
USER MANUAL Sign Cutting Plotter VC-600 VC-1300 VC-1800 Read This Manual Before Using The Plotter. Rev No. Trademark Mentioned in this Manual MUTOH, ValueCut, VC-600, VC-1300, VC-1800, ValueJet are registered
More informationBe sure to read the attached "TO ENSURE SAFE AND CORRECT USE" prior to use. Otherwise, it may cause an unexpected accident or fire.
CE6000 SERIES CUTTING PLOTTER SETUP MANUAL MANUAL NO.CE6000-UM-8M4 Preface Thank you for choosing this product. Carefully keep this manual in a handy location for quick reference as necessity prior to
More informationASTRO UW-1C and RW-1C LABEL PRINTER UNWINDER & WINDER
ASTRO UW-1C and RW-1C LABEL PRINTER UNWINDER & WINDER OPERATOR MANUAL ASTRO MACHINE CORP. 630 Lively Blvd. Elk Grove Village, IL 60007 Phone: (847) 364-6363 Fax: (847) 364-9898 www.astromachine.com SAFETY
More informationDOT MATRIX PRINTER SP6000 SERIES
DOT MATRIX PRINTER SP6000 SERIES Hardware Manual < Approval: CEL > Trademark acknowledgments SP6000 : Star Micronics Co., Ltd. Notice All rights reserved. Reproduction of any part of this manual in any
More informationUSER MANUAL Resolution 0.02mm Speed 300mm/second Software: Wanhao Maker
1 Duplicator 5S & 5S MINI Desktop 3D Printers USER MANUAL Resolution 0.02mm Speed 300mm/second Software: Wanhao Maker 2014/2015 Wanhao USA 3 Table of Contents Welcome 1 Printer Specifications 2 Unboxing
More informationMVPplus Quick Reference Guide
MVPplus Quick Reference Guide Use this guide to operate your printer on a daily basis. For more detailed information, refer to the User Guide. Contents External View...........................................................
More informationKM-4800w. Installation Guide
KM-4800w Installation Guide TABLE OF CONTENTS page 1 Installation Requirements 2 2 Unpacking 3 2. 1 Unpacking 3 2. 2 Confirmation of Accessories 5 3 Leveling the Machine 7 4 Setup of the Roll Deck 9 5
More informationIoline 300/350HF System
Quick Start Guide Ioline 300/350HF System User Notice Trademarks Ioline is a trademark of Ioline Corporation. Other product names, logos, designs, titles, words or phrases mentioned within this publication
More informationTable of Contents. Unpacking and Inspection Setup Loading the Media Mount the Printer on the Wall... 16
WPL25/WHC25 Table of Contents Unpacking and Inspection... 1 Setup... 5 Loading the Media... 6 Mount the Printer on the Wall... 16 LED and Button Functions... 17 Troubleshooting... 18 Unpacking and Inspection
More informationAuto-Cutter. User s Manual. (For CL-S52X/53X/62X/63X, CL-S400DT,CL-E720/E730/E720DT)
Auto-Cutter User s Manual (For CL-S52X/53X/62X/63X, CL-S400DT,CL-E720/E730/E720DT) Contents Notice... 3 SAFETY SIGNS that must be strictly observed!... 4 1. Function... 6 2. Main specifications of auto-cutter...
More information2 1.1 Safety using methods Definition of warning symbols Standard accessories Installation...
Table of Contents 1 Satety precautions... 2 1.1 Safety using methods...2 1.2 Definition of warning symbols...2 2 Standard accessories......6 3 Installation... 7 3.2 Leg frame... 7 3.3 Installation and
More informationSetup Guide. Confirming the Installation Space. Installation space (W x D x H) 70.5 x 66.3 x 61.5 inches (1790 x 1684 x 1560 mm) 23.
Introductory Information Setup Guide ENGLISH Read this manual before attempting to operate the printer. Keep this manual in a handy location for future reference. Caution Instructions in this Setup Guide
More informationVJ-1614 INSTALLATION MANUAL
VJ-6 INSTALLATION MANUAL Please read this manual before using Thank you for purchasing a MUTOH product. This manual explains the steps for unpacking, mounting and basic installation before using the MUTOH
More informationUser's Manual. Metapace L-22D. Label Printer Rev. 1.00
User's Manual Metapace L-22D Label Printer Rev. 1.00 Table of Contents MANUAL INFORMATION & USAGE PRECAUTIONS... 3 1. CONTENT CONFIRMATION... 6 2. PRODUCT PARTS... 7 3. INSTALLATION & USAGE... 9 3-1 POWER
More informationRichter Optica. Instructions for Model: MDS2 Middle School Microscope
Richter Optica info@richter-optica.com Instructions for Model: MDS2 Middle School Microscope Eyepiece 360 Rotatable Head Revolving Nosepiece Carrying Handle Objectives Rack Stop Stage Stage Clips Disc
More informationVJ-1604 INSTALLATION MANUAL
Please read this manual before using Thank you for purchasing a MUTOH product. This manual explains the steps for unpacking, mounting and basic installation before using the MUTOH Full-color inkjet printer
More information9-pin dot matrix printer
9-pin dot matrix printer All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying,
More informationFRESHMARX 9417 QUICK REFERENCE
FRESHMARX 9417 QUICK REFERENCE For more detailed information, refer to the Operator s Handbook available on our Web site (www.monarch.com). Review the printer safety information in the Safety Sheet provided
More informationOcé User manual. Océ CS2024. Quick Start Guide
Océ User manual Océ CS2024 Quick Start Guide Océ Technologies B.V. Copyright 2005, Océ-Technologies B.V. Venlo, The Netherlands. All rights reserved. No part of this work may be reproduced, copied, adapted,
More informationAuto-Cutter CL-S6621. User s Manual
Auto-Cutter CL-S6621 User s Manual Contents Notice... 3 SAFETY SIGNS that must be strictly observed!... 4 1. Function... 6 2. Main specifications of auto-cutter... 6 3. Checking items inside the accessory
More informationLabelMax SP2 User Manual
LabelMax SP2 User Manual 1 GENERAL... 3 1.1 COPYRIGHT DECLARATION... 3 1.2 COMPLIANCES... 3 1.3 INTRODUCTION... 3 2 GETTING STARTED... 4 2.1 UNPACKING AND INSPECTION... 4 2.2 EQUIPMENT CHECKLIST... 4 2.3
More informationIOLINE SUMMIT 2200 MARKER PLOTTER GUIDE TO OPERATIONS
IOLINE SUMMIT 2200 MARKER PLOTTER GUIDE TO OPERATIONS Ioline Corporation Kirkland, Washington IOLINE Summit 2200 Marker Plotter This is the first edition of the Summit 2200 Marker Plotter Guide to Operations.
More informationInstallation Manual. 65 Interactive LED/LCD. Model: HILF65101 (64.56 )
Installation Manual 65 (64.56 ) Model: HILF65101 65 Interactive LED/LCD QUICK SETUP GUIDE For further information, see the user manual. Please contact directly if you have questions on the use of the touch
More informationVJ-1618 INSTALLATION MANUAL
Please read this manual before using Thank you for purchasing a MUTOH product. This manual explains the steps for unpacking, mounting and basic installation before using the MUTOH Full-color inkjet printer
More informationModel No. ET-JPF200BE
Operating Instructions Floor Stand Kit Commercial Use Model No. ET-JPF200BE ET-JPF200WE ENGLISH FRANÇAIS ESPAÑOL DEUTSCH ITALIANO * The above illustration is of this product mounted to an optional projector.
More informationCopyright Information: Firmware (Software) Agreement:
Maintenance Manual Copyright Information: CG Triumvirate is a trademark of Agfa Corporation. CG Times based upon Times New Roman under license from the Monotype Corporation. Windows is a registered trademark
More informationVinyl Express Cougar 24
Vinyl Express Cougar 24 Owner s Manual ValueCut 24 Table of contents 1. Safety precautions...1 2. Standard accessories...3 3. Install machine...5 3.1 Installation and connection......5 3.2 Install cutting
More informationThe Nureva Span ideation system. Installation guide. Single panoramic system
The Nureva Span ideation system Installation guide Single panoramic system Important SAFETY WARNINGS Prior to the installation of this product, the installation instructions should be completely read and
More informationUser Manual. Trinocular Stereo Microscope
User Manual Trinocular Stereo Microscope Model V434 XV434 Series MicroscopeNet.com Table of Contents i. Caution.. 1 ii. Care and Maintenance... 2 1. Component Illustration... 3 2. Installation 4 3. Operation....6
More informationScanPartner 600C Image Scanner. User s Manual
ScanPartner 600C Image Scanner User s Manual Version 1.0 (Doc. No. 250-0062-0) Table of Contents 1. INTRODUCTION 3-4 2. INSTALLATION AND CONNECTIONS. 5-13 2.1 Shipping Bracket 5 2.1.1 Removing the Shipping
More informationMini Cutting Plotter. NODE 101/ Cutok USER S MANUAL
Mini Cutting Plotter NODE 101/ Cutok USER S MANUAL Thank you for purchasing cutter NODE 101 / Cutok. It can be used for cutting vinyl, heavy-cardstock, paper and sticker film as well as pen plotting. Please
More informationCE5000 Series USER S MANUAL MANUAL NO. CE5000-UM-153
CE5000 Series CUTTING PLOTTER USER S MANUAL MANUAL NO. CE5000-UM-153 PREFACE Thank you for choosing a Graphtec CE5000 Series cutting plotter. The CE5000-60/120 cutting plotters employ a digital servo
More informationRemoval and Installation 8
Removal and Installation 8 8 Introduction 8-2 Service Calibration Guide to Removal and Installation 8-4 Window 8-8 Covers and Trims 8-12 Rear Tray 8-31 Rear Cover 8-32 Media Lever 8-33 Media Lever Position
More informationUsers Manual STP-103II. Thermal Printer Rev
Users Manual STP-103II Thermal Printer Rev. 1.00 http://www.bixolon.com Safety Precautions The instructions shown below must be followed to prevent possible danger or damage by using the product incorrectly.
More informationStereo Turntable System
3-866-873-15(1) Stereo Turntable System Operating Instructions OWNER S RECORD The model and serial numbers are located at the rear. Record the serial number in the space provided below. Refer to them whenever
More informationVinyl Express Qe60+ Signwarehouse.com. USER S MANUAL MANUAL NO. VEXQe6+-UM-151 CUTTING PLOTTER
Vinyl Express Qe60+ CUTTING PLOTTER USER S MANUAL MANUAL NO. VEXQe6+-UM-151 Signwarehouse.com PREFACE Thank you for choosing a Signwarehouse Vinyl Express Series cutting plotter. The Vinyl Express cutting
More informationXerox 8264E Color Wide Format Printer 100kg Unwinder / Winder
November 2009 70P3070 Xerox 8264E Color Wide Format Printer 00kg Unwinder / Winder 2009 Xerox Corporation. All rights reserved. Xerox, the sphere of connectivity design, and Xerox 8264E Color Wide Format
More informationfi-4120c Image Scanner
P3PC-E007-01EN fi-4120c Image Scanner Cleaning and Maintenance 5 DAILY CARE This chapter describes how to clean the scanner. WARNING When cleaning the scanner, turn off the power, and unplug the AC cable
More informationHD Mini IR Waterproof Bullet Network Camera. Quick Start Guide. Version 1.0.0
HD Mini IR Waterproof Bullet Network Camera Quick Start Guide Version 1.0.0 Welcome Thank you for purchasing our Network camera! This user s manual is designed to be a reference tool for your system. Please
More informationPA Series. Available in 6.0MP and 8.0MP
Camera Quick Install Guide PA Series Available in 6.0MP and 8.0MP Thank you for purchasing a PA Series CCTV Surveillance Camera. This Quick Install Guide covers basic setup, installation and use of your
More informationCANADIAN D.O.C. WARNING
Each product and program carries a respective written warranty, the only warranty on which the customer can rely. Avery Dennison Corp. reserves the right to make changes in the product, the programs, and
More informationM7 SERIES Thermal Printer Service Manual 4. PART LIST. 4.1 Main Printer Assemblies
4. PART LIST 4.1 Main Printer Assemblies 31 No. Part No. Description Remark Spare Requirement 1 120732 Electronics cover 1 pc 2 N/A Mainframe 1 pc 3 120733 Cover, front 1 pc 4 120734 Top right side cover
More informationHD Mini IR Waterproof Fixed Network Camera. Quick Start Guide. Version 1.2.0
HD Mini IR Waterproof Fixed Network Camera Quick Start Guide Version 1.2.0 Welcome Thank you for purchasing our Network camera! This user s manual is designed to be a reference tool for your system. Please
More informationAvailable in 2.0MP, 4.0MP and 8.0MP variants
Camera Quick Install Guide FBMINIIR Series Available in 2.0MP, 4.0MP and 8.0MP variants Thank you for purchasing a FBMINIIR Series CCTV Surveillance Camera. This Quick Install Guide covers basic setup,
More informationAstroJet TM M2 Quick Start Guide
AstroJet TM M2 Quick Start Guide Step 1 Remove Printer and Accessories from packaging. Place Printer on a flat, even surface. Step 2 Remove Service Station Transport Tab 1. Open Top Cover. 2. Open Print
More informationWhisper-Ride
11/16/2007 LR (1) CAUTION: Before you begin any of the installation procedures on page 3, read and follow the warnings and safety instructions on this page. WARNING! THIS IS NOT A TOY! WARNING! CHILDREN
More informationCraft ROBO USER S MANUAL MANUAL NO. CE50CRP-UM-152
Craft ROBO Pro Craft ROBO USER S MANUAL MANUAL NO. CE50CRP-UM-152 PREFACE Thank you for choosing a Graphtec Craft ROBO Pro (CE5000-40-CRP) cutting plotter. The Craft ROBO Pro cutting plotters employ a
More informationEPSON ActionLaser Read This First. eepa POLLUTION PREVENTER
EPSON ActionLaser 1400 Read This First eepa POLLUTION PREVENTER This booklet is to help you set up your printer and begin printing quickly. It also gives you instructions for routine maintenance. If you
More informationDisconnect the battery to ensure there will be no shorted wires during the installation procedure.
The round-style headunit receiver radio features Bluetooth technology allowing music to wirelessly stream from your compatible Bluetooth-enabled device. Control the audio from a distance -- all from your
More informationINSEBO2IRF 2.1MP 1080P IP Eyeball Camera with IR
INSEBO2IRF 2.1MP 1080P IP Eyeball Camera with IR Quick Start Guide Version 1.0.0 Welcome Thank you for purchasing our Network camera! This user s manual is designed to be a reference tool for your system.
More informationMH Series Troubleshooting Guide: Rough Draft
MH Series Troubleshooting Guide: Rough Draft Poor Cutting Lifting Corners: If the corners of the material are getting pulled up then the carriage speed will need to be reduced and the blade depth should
More informationCANADIAN D.O.C. WARNING
Each product and program carries a respective written warranty, the only warranty on which the customer can rely. Avery Dennison Corp. reserves the right to make changes in the product, the programs, and
More informationLexmark X203n and X204n Series. Maintenance Guide
Lexmark X203n and X204n Series Maintenance Guide February 2011 www.lexmark.com Contents...3 Cleaning the exterior of the printer...3 Cleaning the scanner glass...4 Cleaning the ADF separator rollers...5
More informationTOP - 1. Instruction Manual. Version 1.0 Produced in Jan. 2004
Version 1.0 Produced in Jan. 2004 Instruction Manual LCD monitor IV-08MP Thank you for purchasing the SHARP IV-08MP LCD monitor. Read this introductory instruction manual carefully to thoroughly familiarize
More informationGerber Tempo 600 Setup Manual and Quick Start Guide
Gerber Tempo 600 Setup Manual and Quick Start Guide Gerber Tempo 600 Setup Manual...2 1. Check the shipment...2 2. Prepare the connection cable...3 3. Prepare the power source...3 4. Install the plotter
More informationUser Guide PCT Multi Touch Monitor Display OF17T100-A1-PCT
User Guide PCT Multi Touch Monitor Display OF17T100-A1-PCT American Industrial Systems - OF17T100-A1-PCT User Guide Page 1 The information contained in this document is subject to change without notice.
More informationVJ-1304 INSTALLATION MANUAL
Please read this manual before using Thank you for purchasing a MUTOH product. This manual explains the steps for unpacking, mounting and basic installation before using the MUTOH Full-color inkjet printer
More informationNexa PX700IIS Thermal Receipt Printer. User Manual. P a g e 1
Nexa PX700IIS Thermal Receipt Printer User Manual P a g e 1 Table of Contents Safety Notice... 3 Available Functions... 3 Main Features... 4 Technical Specifications... 4 Unpacking the Printer... 5 Connection
More informationMUTOH EUROPE N.V. Tel.:32-(0) Fax:32-(0)
MUTOH INDUSTRIES LTD. Tel.:8-(0)-570-00 Fax:8-(0)-570-00 E-mail:ibd@mutoh.co.jp http://www.mutoh.co.jp MUTOH AMERICA INC. Tel.:-80-968-777 Fax:-80-968-7990 E-mail:sales@mutoh.com http://www.mutoh.com MUTOH
More informationAssembly and Setup Manual
M-12 Series Copyboard / C-12 Series Captureboard Assembly and Setup Manual This is the installation and assembly manual for the M-12 series Copyboard and C-12 series Captureboard. (The copyboard and/or
More informationAvailable in 2.0MP, 4.0MP, 6.0MP and 8.0MP, with 2.8mm and 3.6mm lenses.
Camera Quick Install Guide VDMINIIRCB Series Available in 2.0MP, 4.0MP, 6.0MP and 8.0MP, with 2.8mm and 3.6mm lenses. Thank you for purchasing a VDMINIIRCB Series CCTV Surveillance Camera. This Quick Install
More informationUser s Manual M EN
User s Manual Before Use.................................. 2 Unpacking.................................. 3 Part Names and Functions................... 4 Setup....................................... 6 Installing/Replacing
More information2015 SIMMCONN LABS, LLC. All rights reserved. NewScope-T1 Operation Manual
2015 SIMMCONN LABS, LLC. All rights reserved NewScope-T1 Operation Manual April 12, 2017 NewScope-T1 Operation Manual 1 Introduction... 3 2 Installation... 4 2.1 Initial Inspection... 4 2.2 Installation
More informationModel: PTTC4U. Multifunction Turntable With MP3 Recording, USB-to-PC, Cassette Playback
Model: PTTC4U Multifunction Turntable With MP3 Recording, USB-to-PC, Cassette Playback Read instructions carefully before use and store in a safe place for future reference. IMPORTANT SAFETY INSTRUCTIONS
More informationMi50 Inverted Microscope User s Manual. Fein.
Mi50 Inverted Microscope User s Manual Fein info@feinoptic.com Mi50 Microscope Components Siedentopf Trinocular Head Stage Plate Mechanical Stage Locking Screw Hex Wrench Storage Beam Splitter Dust Protector
More informationFull HD IP Vandal Dome Camera
Quick Start Guide Full HD IP Vandal Dome Camera O3VLD1 Version 1.0 Welcome Thank you for purchasing this network camera! This owner s manual is designed to be a reference tool for your system. Please read
More informationS-100X / S-200X Snow Machine User Manual
S-100X / S-200X Snow Machine User Manual English Français Deutsch 中文 2014 Antari Lighting and Effects Ltd. 1 2 User Manual Antari S-100X & S-200X Snow Machine Introduction Thank you for choosing an ANTARI
More information3 Indexer Installation For PRSalpha Tools
888-680-4466 ShopBotTools.com 3 Indexer Installation For PRSalpha Tools Copyright 2016 ShopBot Tools, Inc. page 1 Copyright 2016 ShopBot Tools, Inc. page 2 Table of Contents General Safety and Precautions...5
More information3M Duplex Polishing Machine 6851-E with Universal Dual Holder Instructions
3M Duplex Polishing Machine 6851-E with Universal Dual Holder Instructions Safety Information Read, understand and follow all safety information contained in these user instructions prior to use of the
More informationQUICK REFERENCE. Connecting the Cables
QUICK REFERENCE This Quick Reference contains supply loading and general care and maintenance procedures for the Monarch 9860 printer. For more detailed information, refer to the Operator s Handbook available
More informationE-37-V Dome Network Camera. Quick Start Guide
E-37-V Dome Network Camera Quick Start Guide i Welcome Thank you for purchasing our Network camera! This user s manual is designed to be a reference tool for your system. Please read the following safeguard
More informationStartup Guide C01
Startup Guide 4012988-00 C01 Startup Guide English Where to Find Information........................ 2 Safety Instructions.............................. 4 Important Safety Instructions...........................
More information1. Review the printer safety information in the Regulatory Compliance document provided with your printer.
QUICK REFERENCE This Quick Reference contains supply loading information and general care and maintenance procedures for the Monarch Pathfinder Ultra Platinum 6039 printer. For more detailed information,
More informationDahua HD IR Vari-Focal Fixed Network Camera. Quick Start Guide
Dahua HD IR Vari-Focal Fixed Network Camera Quick Start Guide Version 1.0.0 Dahua Technology CO., LTD Welcome Thank you for purchasing our Network camera! This user s manual is designed to be a reference
More informationAssembly and Setup Manual
M-11 Series Copyboard/C-11 Series Captureboard Assembly and Setup Manual This is the installation and assembly manual for the M-11 series/c-11 series. To the Customer Specialized techniques are required
More informationImageScan Pro 800ix Series High-Speed ADF Scanner. Installation and Setup Guide. Installation and Setup Guide
ImageScan Pro 800ix Series High-Speed ADF Scanner Installation and Setup Guide Installation and Setup Guide Box Contents: 1. Scanner 2. USB Cable 3. AC Adapter 4. Stacker Tray 5. Installation Guide 6.
More informationFC8600 SERIES. User's Manual CUTTING PLOTTER MANUAL NO.FC8600-UM-151
FC8600 SERIES CUTTING PLOTTER User's Manual MANUAL NO.FC8600-UM-151 TO ENSURE SAFE AND CORRECT USE l To ensure the safe and correct use of your plotter, read this manual thoroughly prior to use. l After
More informationOnePlus 5 Screen and Digitizer Assembly Replacement
OnePlus 5 Screen and Digitizer Assembly Replacement Follow this guide to replace the screen and digitizer for the OnePlus 5. This replaces the screen as well as the frame it is attached to. Written By:
More informationWAVECOM INSTRUMENTS PTY LTD
WAVECOM INSTRUMENTS PTY LTD www.wavecom.com.au WAVECOM TT040-50 THERMAL TRANSFER BAR CODE PRINTER USER MANUAL 1 Table of Contents Copyright Declaration 3 Introduction 3-4 Product Introduction Compliances
More informationContents. - i - Ver.:2
Contents 1 Accessories of D-Point 2... 2 2 Connecting Projector to PC... 4 3 Pen Action... 4 4 Driver Installation... 5 5 Configuration Setting... 8 6 D-Point 2 Pull-up Menu... 12 7 DT02 Multi-touch Interactive
More informationK Service Source. StyleWriter
K Service Source StyleWriter K Service Source Basics StyleWriter Basics Introduction - 1 Introduction The StyleWriter is a serial bubble jet ink-on-demand printer. The StyleWriter prints up to 1/3 page
More informationLuna. Instruction Manual
Luna Instruction Manual Safety Guidelines Product Components Explained. Luna Case. Luna Dock. Luna RFID Fob Luna Installation. Installation Guidelines. Fixing from Below. Fixing from Above. Luna Case Installation
More informationUser's Manual SRP-770II. Label Printer Rev
User's Manual Label Printer Rev. 1.12 http://www.samsungminiprinters.com Table of Contents Manual Information & Usage Precautions 3 1. Content Confirmation 7 2. Product Part Names 8 3. Installation & Usage
More informationAirport Bag Tag Printers. Level 1 Repair Program. Unimark ET6000 Unimark 8500
Level 1 Repair Program Unimark ET6000 Unimark 8500 Version: 2.2 Date: February 15, 2005 Owner: Business Support Author: Jack Michko Table of Contents Table of Contents Table of Contents... ii Unimark ET6000
More information