Linear Position Transducer HLT 1000-R2

Transcription

1

2 7 Linear Position Transducer HLT 1000-R2 Description: The sensor works on the principle of magnetostriction. This measuring principle determines with high accuracy the position, distance and/or speed and is based on elapsed time measurement. On the basis of this non-contact and wear-free measurement system, HYDAC offers a version in pressureresistant stainless steel housing for complete integration in hydraulic cylinders. The different output signals (analogue/canopen) facilitate the connection of all HYDAC ELECTRONIC GMBH measurement and control devices as well as connection to standard evaluation systems (e.g. also to PLC controls). The main areas of application are in mobile hydraulics. Special features: High accuracy, e.g. ± 0.05 % FS for CANopen Very robust housing High resistance to shock and vibration Excellent EMC characteristics Non-contact and wear-free Persuasive price / performance ratio Technical data: Input data Measuring ranges mm Measured variable Distance, position, speed Mechanical connection Cylinder-integrated Housing Stainl. steel: pressure resistance 450 bar Output data Signal output Current: ma or ma Voltage: V or V V or V CANopen Measuring accuracy Analogue CANopen Resolution 12 bit 0.1 mm min. 0.1 mm Non-linearity ± 0.05 % FS ± 0.05 % FS Hysteresis ± 0.1 mm ± 0.1 mm Repeatability ± 0.1 mm ± 0.1 mm Temperature coefficient ± 0.01 % FS / C ± % FS / C Installation position and travel speed Optional Environmental conditions Operating temperature range C Relative humidity 90 %, non-condensing Storage temperature range C, dry Vibration resistance to DIN EN at Hz 20 g at 5 khz 15 g Shock resistance to 50 g DIN EN (11 ms) mark EN / 2 / 3 / 4 EMC - Emitted interference DIN EN Interference resistance DIN EN Housing / Stainless steel, pressure-resistant Protection class to IEC ) IP 67 Other data Electrical connection 1) Flying leads Separate male panel mount connection M12x1 Supply voltage V DC Current consumption without load max. 100 ma Weight Depends on length Note: Reverse polarity protection of the supply voltage and excess voltage protection are provided. FS (Full Scale) = relative to the complete measuring range 1) Other versions are possible. E /

3 7 Model code: HLT R2 XXX XXX XXXX 000 Mobile Design/Geometry type 1 = Rod Mechanical connection R2 = Cylinder-integrated Electrical connection Cable output K01 = Flying lead, length 1 m K02 = Flying lead, length 2 m K05 = Flying lead, length 5 m K10 = Flying lead, length 10 m Separate male panel mount connection M12x1 (4 pole for signal output analogue 5 pole for signal output CANopen) L06 = 60 mm cable length L18 = 180 mm cable length L24 = 240 mm cable length Signal output C01 = Analogue ma, 3 conductor C02 = Analogue ma, 3 conductor B01 = Analogue V B02 = Analogue V G01 = Analogue V G02 = Analogue V CAN = CANopen Measuring range in mm (50 to 2500 mm) Example 0150 = 150 mm Modification 000 = Standard Pin connections: Cable outlet Core Analogue CANopen brown +U B +U B white 0 V 0 V green Analogue CAN_L yellow n.c. CAN_H M12x1, 4 pole Pin 1 +U B 2 n.c. 3 0 V 4 Signal Notes: Special models on request. On instruments with a different modification number, please read the label or the technical amendment details supplied with the instrument. Items supplied: HLT 1100-R2 Installation instructions German/English HLT 1100 CD incl. case M12x1, 5 pole Accessories: Appropriate accessories, such as position magnets, etc. can be found in the Accessories section of the Electronics brochure. The recommended position magnet ZBL MR33, part no , must be ordered separately. Dimensions: Pin Signal Description 1 n.c. 2 +U B supply+ 3 0 V supply- 4 CAN_H bus line dominant high 5 CAN_L bus line dominant low E /11.13 Damping zone Measuring length Zero position Note: The information in this brochure relates to the operating conditions and applications described. For applications and operating conditions not described, please contact the relevant technical department. Subject to technical modifications. HYDAC electronic GmbH Hauptstraße 27, D Saarbrücken Telephone +49 (0) Fax +49 (0) electronic@hydac.com Internet: 132

4 Linear Position Transmitter HLT 2150 Rod Version, Partly-Integrated Description: The HLT 2150 is a linear position transmitter which, due to its compact design, was developed in particular for use in applications where space is very limited. A wide range of accessories such as magnets is available for individual adaptation to the particular application. The HLT 2150 ist available for measuring ranges up to 2.5 m. The different output signals (analogue, CANopen) facilitate the connection of all HYDAC ELECTRONIC GMBH measurement and control devices as well as connection to standard evaluation systems (e.g. also to PLC controls). The main fields of application for the HLT 2150 are, for example, general positioning tasks in mechanical engineering and in mobile and industrial hydraulics, as a partly-integrated solution in hydraulic cylinders. Special features: Compact design High resistance to shock and vibration Excellent EMC characteristics For measuring ranges up to 2.5 m Non-contact and wear-free Persuasive price / performance ratio Technical data: Input data Measuring ranges mm Pressure resistance 450 bar Peak pressure 630 bar Housing Stainless steel ( / ) Output data Signal output Current: ma or ma Voltage: V or V V or V V V CANopen Measuring accuracy Analogue CANopen Resolution 12 bit, 0.1 mm 0.1 mm Ohmic resistance to GND Current: Ω Voltage: > 2 kω Non-linearity ± 0.05 % FS ± 0.02 % FS Hysteresis ± 0.1 % FS ± 0.1 mm Repeatability ± 0.1 % FS ± 0.1 mm Temperature coefficient ± 0.01 % FS / C ± % FS / C Sampling rate (internal) 2 ms 2 ms Installation position and travel speed No restrictions Environmental conditions Operating temperature range C Storage temperature range C, dry Fluid temperature range C Relative humidity 90 %, non-condensing mark EN / 2 / 3 / 4 Vibration resistance to DIN EN at Hz at 5 khz 20 g 15 g Shock resistance to 50 g DIN EN (11 ms) Protection class to IEC IP 67 Other data Electrical connection M12x1 plug Supply voltage V DC Residual ripple of supply voltage 250 mvpp Current consumption without output max. 100 ma Weight Depends on length Note: Reverse polarity protection of the supply voltage, excess voltage and short circuit protection are provided. FS (Full Scale) = relative to the complete measuring range E /

5 Model Code: HLT R1 XXX - XXX XXXX 000 Pin connections: M12x1, 4 pole Design/Geometry type 1 = Rod Model R1 = Threaded flange M18x1.5 Electrical connection Signal output analogue M04 = Male M12x1, 4 pole Signal output CANopen M05 = Male M12x1, 5 pole Signal output C01 = Analogue ma, 3 conductor C02 = Analogue ma, 3 conductor B01 = Analogue V B02 = Analogue V F11 = CANopen G01 = Analogue V G02 = Analogue V G03 = Analogue V G04 = Analogue V Measuring range in mm (50 to 2500 mm) Example 0150 = 150 mm Modification 000 = Standard Notes: Special models on request. The position magnet must be ordered separately. Pin 1 +U B 2 n.c. 3 0 V 4 Signal M12x1, 5 pole Pin Signal Description 1 n.c. 2 +U B supply V supply - 4 CAN_H bus line dominant high 5 CAN_L bus line dominant low Items supplied: HLT 2150 Operating instructions Accessories: Appropriate accessories, such as position magnets, etc., can be found in the Accessories section of the Electronics brochure. Dimensions: Measuring length M12 4pole / 5pole Note: The information in this brochure relates to the operating conditions and applications described. For applications and operating conditions not described, please contact the relevant technical department. Subject to technical modifications. E /05.15 HYDAC ELECTRONIC GMBH Hauptstraße 27, D Saarbrücken Telephone +49 (0) Fax +49 (0) electronic@hydac.com Internet: 2

6

7

8

9

10

11