Polymer Electric. Operating Instructions. Control Unit SG-TRS 3X8. Version 1

Transcription

1 Operating Instructions Control Unit SGTRS 3X8 Version SGTRS V= SGTRS 38 4 V= Original instructions GmbH & Co KG Örlinger Straße Ulm GERMANY Tel: Fax: infoulm@mayserde Internet: wwwmaysercom

2 Content About these operating instructions 3 Intended use 4 Safety instructions 4 Parts supplied 5 You also require 5 Transport and storage 6 Packaging and transport 6 Storage 6 Product overview 6 Connections 6 LEDs information 6 Operation, installation and commissioning 7 Operation 7 Installation 7 Commissioning 9 Check operation 9 Correlation 10 Recommissioning 10 Automatic reset 10 Connection examples 11 Maintenance and cleaning 11 Maintenance 11 Cleaning 11 Troubleshooting and remedies 12 Correlation 13 Replacement parts 14 Disposal 14 Conformity 14 EC Design Test 14 Technical Data 14 Copyright The reproduction, distribution and utilization of this document as well as the communication of its contents without express authorization is prohibited Offenders will be held liable for the payment of damages All rights reserved in the event of the grant of a patent, utility model or design Mayser Ulm 2011 Page /15 Operating Instructions SGTRS 3X v10

3 About these operating instructions These operating instructions are part of the product Mayser accepts no responsibility or warranty claims for damage and consequential damage due to failure to observe the operating instructions Read operating instructions carefully before use Keep operating instructions for the complete service life of the product Pass operating instructions on to every subsequent owner or user of the product Add any supplement received from the manufacturer to the operating instructions Validity These operating instructions are only valid for the products specified on the title page Target group The target group of these operating instructions are operators and trained specialist personnel who are familiar with installation and commissioning Other applicable documents In addition to the operating instructions, observe the following documents: Drawing of the sensor system (optional) Wiring diagram (optional) Installation instructions of the sensors used Symbols used Symbol Meaning Action with one step or with more than one step where the order is not relevant 1 3 Action with more than one step where the order is relevant Bullets first level Bullets second level (see Assembly) Crossreference v10 Operating Instructions SGTRS 3X8 Page 3/15

4 Danger symbols and information Symbol DANGEr Meaning Immediate danger leading to death or serious injury CAUTION Possible danger which may lead to slight injury or damage to property Information on easier or safer working practices Intended use The Control Unit is designed for signal processing of a pressuresensitive protective device (PSPD) for buses and trains It evaluates the output signals of sensors with transponder technology as well as sensors with monitoring resistor 1k2 The integrated output signal switching device (OSSD) transmits the evaluated safety signals directly to the downstream control The Control Unit complies with IEC SIL2 and IEC SIL2 When used in conjunction with a TRS transponder system the Control Unit functions as a radio module per the R&TTE Directive 1999/5/EEC Safety instructions Do not modify Control Unit Never manipulate or modify the Control Unit Check supply voltage Check supply voltage It must correspond with the connecting voltage U S on the type plate Maintain distance When installing in the switch cabinet, ensure sufficient distance from heat sources (at least 2 cm) Protect from sunlight In the case of surface installation, ensure that the Control Unit is protected from direct sunlight Page 4/15 Operating Instructions SGTRS 3X v10

5 Observe pin assignment Observe pin assignment when connecting the supply voltage Protect relay contacts Risk of welding: Protect the relay contacts externally Fit spark absorbers When connecting inductive loads, fit spark absorbers (RC modules) to the consumer Do not cross link Control Unit Do not cross link the Control Unit with other Control Units Terminals ANT1, ANT2 and Y1, Y2 are not voltage free Do not overload Control Unit Ensure that the specified switching current is not exceeded Continue redundancy Make sure you wire the unit directly in the control circuit or that the downstream control is also in dual channel mode In the event of a fault, put out of operation In the event of malfunctions and visible damage, put the Control Unit out of operation Do not use in ATEX zones Do not use the Control Unit in potentially explosive environments (ATEX) The Control Unit is not authorised for use in these zones Parts supplied 1 Control Unit Enclosure with electronics module 1 Operating Instructions 1 Declaration of Conformity Check the scope of supply for completeness and the perfect condition of the product immediately after receipt You also require 1x round plug connector set M23, 9poles, socket (Part No ) v10 Operating Instructions SGTRS 3X8 Page 5/15

6 Transport and storage Packaging and transport The Control Units are packed individually in cardboard boxes Several Control Units are stacked in one large cardboard box The documents are enclosed separately Storage Store the Control Units in the original packaging in a dry place Observe the storage temperatures given in the technical specifications Product overview Connections Plug X1 Signal PIN Round connector Supply voltage Sensor A1 A2 Y1 Y2 Switching channel Switching channel Equipotential bonding M23 Socket X2 Signal PIN Round connector Transmitting antenna ANT1 ANT2 1 2 M16 LEDs information green LED Power : supply voltage connected yellow LED Channel 1 active : channel 1 activated yellow LED Channel 2 active : channel 2 activated green LED K1/K2 active : switching channel 1 and 2 closed red LED Channel 2 fault : channel 2 fault red LED General fault : internal fault Page 6/15 Operating Instructions SGTRS 3X v10

7 Operation, installation and commissioning Operation The singlefaultsafe electronics module has dual channels (redundant) Each channel controls a forceguided relay and additionally monitors the relay of the other channel The electronic system monitors the sensor on channel 2 (= sensor 2) and the sensor with integrated transponder chip (= sensor 1) The control unit is powered with DC 110 V or DC 24 V When the supply voltage is connected, the green Power LED is lit up When both sensors are not activated, relays K1 and K2 energise, channel 1 and 2 are closed If one of the sensors is activated, relays K1 and K2 deenergise Green LED K1/ K2 active go off, yellow LED Channel 1 active or/and yellow LED Channel 2 active are lit, Channel 1 and 2 are open The unit does not work if channel 1 is not connected Channel 2 can be bridged with a resistor if it is not required Installation danger Danger of injury due to electrocution! Disconnect all devices and live parts in the immediate environment of the power supply and protect them against being switched on again (see relevant operating instructions) Check that all devices and parts are disconnected from the power supply caution Impaired operation due to overheating The operation of the protective device may be impaired due to overheating of the Control Unit When installing in the switch cabinet, ensure sufficient distance from heat sources (at least 2 cm) In the case of surface installation, ensure that the Control Unit is protected from direct sunlight Mount the Control Unit in any position with screws Ø 4 mm For this, remove the enclosure cover v10 Operating Instructions SGTRS 3X8 Page 7/15

8 (rear) Caution Overall safety endangered The quality and reliability of the interface between the protective device and the machine influences the overall safety Install the interface very carefully 1 Wire the transmitting antenna, sensor, relay contacts as well as supply voltage and equipotential bonding at the round connectors sensor channel 2 transmitting antenna channel 1 caution Protection class can decrease The quality of the round plug connections on X1 and X2 affect the protection class of the Control Unit Take special care when carrying out the screw connections Page 8/15 Operating Instructions SGTRS 3X v10

9 Commissioning 1 Reinstall the enclosure cover The screws used to fix the lid of the enclosure also ensure the equipotential bonding to the lower part of the enclosure Tighten all screws well Connect the supply voltage danger Danger of injury due to electrocution! Never unplug plug connections with the power on Check operation 1 Make sure no sensors are activated and transponder antenna is in field green LED Power is lit green LED K1/K2 active is lit contacts of switching channels 1 and 2 closed Activate sensor 1 green LED Power is lit yellow LED Channel 1 active is lit green LED K1/K2 active go off contacts of switching channels 1 and 2 open 3 Repeat step 1 4 Activate sensor 2 green LED Power is lit yellow LED Channel 2 active is lit green LED K1/K2 active go off contacts of switching channels 1 and 2 open 5 Repeat step 1 6 Remove the transponder antenna from the field Alternately place a metal plate between the transponder antenna and the transmitting antenna green LED Power is lit yellow LED Channel 1 active is lit green LED K1/K2 active go off contacts of switching channels 1 and 2 open 7 Repeat step v10 Operating Instructions SGTRS 3X8 Page 9/15

10 8 Disconnect sensor 2 green LED Power is lit red LED Channel 2 fault is lit green LED K1/K2 active go off contacts of switching channels 1 and 2 open 9 If the result of the operational test is positive, enter the date on the type plate under installation date Correlation LEDs Remedy Power Channel Channel K1/K2 Channel General 1 active 2 active active 2 fault fault LED off: LED on: green yellow yellow green red red Supply voltage connected, Control Unit ready: (1) transponder antenna not in field, sensor 2 not activated, switching channels open (2) transponder antenna in field, sensor 1 activated, sensor 2 not activated, switching channels open Transponder antenna in field, sensor 1 and 2 not activated, switching channels closed Transponder antenna in field, sensor 1 not activated, sensor 2 activated, switching channels open (1) Transponder antenna not in field, sensor 2 activated switching channels open (2) Transponder antenna in field, sensors 1 and 2 activated, switching channels open Recommissioning danger Danger of injury! Never start your machine as long as the danger remains Automatic reset The Control Unit works without a reset command If the sensor is enabled after actuation, relays K1 and K2 reenergise after a delay t w Check for proper functioning after recommissioning (see section Commissioning) Page 10/15 Operating Instructions SGTRS 3X v10

11 Connection examples Maintenance and cleaning Maintenance The Control Unit is maintenancefree Repeat the operational test monthly Cleaning danger Danger of injury due to electrocution! Disconnect the Control Unit as well as all devices and live parts in the immediate environment of the power supply and protect them against being switched on again (see relevant operating instructions) Check that all devices and parts are disconnected from the power supply Clean the outside of the enclosure with conventional cleaning products Allow the enclosure to dry before recommissioning v10 Operating Instructions SGTRS 3X8 Page 11/15

12 Troubleshooting and remedies Fault display Possible cause Remedy green LED POWER off No or incorrect supply voltage 1 Check supply voltage, compare with type plate green LED K1/K2 active off yellow LED Channel 2 active on and sensor 2 not activated Prerequisite: The Control Unit is connected to the supply voltage and sensor The sensor is not activated If supply voltage is correctly connected: Control Unit is faulty Channel 1: Fault on transponder side Check terminal connections Replace Control Unit Check whether transponder antenna is in field and that sensor 1 not activated Take transponder antenna out of field and place reference transponder T02 (Part No ) in the field Check if switching channels energise 4 If yes: Replace entire transponder side Channel 1: Fault on Control Unit side 1 Measure voltage on terminals 1 and 2: set value > AC 25 V / 125 khz Channel 2: Fault on sensor 2 Sensor or supply line faulty (line disconnection) Actual value < AC 25 V: Replace transmitting antenna Fault still exists: Control Unit faulty Check if yellow LED Channel 2 active or red LED Channel 2 fault on Connect resistor 1k2 instead of sensor 2 Fault eliminated: Replace sensor 2 Fault still exists: Control Unit faulty Measure resistor on sensor 2 : set value = 1k2 ±5% Actual value set value: Replace Sensor 2 Connect resistor 1k2 instead of sensor 2 Fault eliminated: Replace sensor 2 Fault still exists: Control Unit faulty Page 12/15 Operating Instructions SGTRS 3X v10

13 Fault display Possible cause Remedy red LED Channel 2 fault on and sensor 2 not activated Sensor or supply line faulty (cable break) 1 Measure resistor on sensor 2: set value = 1k2 ±5% Actual value set value: Replace sensor Connect resistor 1k2 instead of sensor 2 Fault eliminated: Replace sensor 2 and supply line red LED General fault on Control Unit faulty 5 Fault still exists: Replace Control Unit Replace Control Unit Fault can still not be detected? Contact MayserSupport: Tel Correlation LEDs Meaning Power Channel Channel K1/K2 Channel General 1 active 2 active active 2 fault fault LED off: LED om: green yellow yellow green red red CPU fault RAM fault ROM fault Relay fault Program run fault Fault during test SLBetätigt (transponder antenna in field) Fault during test SLStörung (transponder antenna in field) Fault during test SLBetätigt (transponder antenna not in field) Fault during test SLStörung (transponder antenna not in field) v10 Operating Instructions SGTRS 3X8 Page 13/15

14 Replacement parts Caution Overall safety endangered If the sensor and Control Unit are not replaced with original parts from Mayser, operation of the protective device may be impaired Only use original parts from Mayser Disposal The Control Units produced by Mayser are professional electronic tools exclusively intended for commercial use (socalled B2B devices) Unlike devices mainly used in private households (B2C), they may not be disposed of at the collection centres of public sector disposal organisations (eg municipal recycling depots) At the end of their useful life, the devices may be returned to us for disposal WEEE reg no DE Conformity The product design fulfils the fundamental requirements of the R&TTE Directive 1999/5/EEC The Declaration of Conformity is available in the Downloads section of the website: wwwmaysersicherheitstechnikde/english/indexasp EC Design Test The product was tested by an independent institute An EC design type test certificate confirms conformity The EC design type test certificate is available in the Downloads section of the website: wwwmaysersicherheitstechnikde/english/indexasp Technical Data SGTRS 3X8 DC 24 V DC 110 V Test principles EN 17602, EN 50155, IEC 61508, IEC Connecting voltage U S Voltage tolerance Nominal current External protection Power consumption Times Reaction time t a Restart time t w 30% to +25% 95 ma 500 ma T < 3 W < 150 ms < 200 ms 30% to +25% 20 ma 500 ma T < 3 W < 150 ms < 200 ms Page 14/15 Operating Instructions SGTRS 3X v10

15 SGTRS 3X8 DC 24 V DC 110 V Safety classifications EN 1760: Reset IEC IEC EN : Creep distance and air gap Control Unit Inputs Sensor 1 Voltage Line length (max) transmitting antenna SL/TRS Sensor 2 Monitoring resistor shortcircuit resistance Line resistance Line length (max) Switching thresholds Sensor active cable break Control Unit Outputs Switching channel 1 and 2 Relay Type Switching voltage (max) Switching current (max) Switching current (min) Switching capacity (max) Switching operations, mechanical Switching operations, electrical Contact fuse protection external Mechanical operating conditions Round plug connectors X1: M23, 9poles X2: M16, 3poles IEC 60529: Degree of protection max humidity (23 C) Operating temperature Storage temperature EN 50155: temperature class IEC 61373: Schock and vibration Dimensions (W H D) Weight without SIL2 SIL2 for soiling degree 2, overvoltage category II / 110 V 1, 2 AC 120 V / 125 khz 50 m 30 m Y1, Y2 1k2 Ohm 400 Ohm 10 Ohm 10 m < 600 Ohm > 1k8 Ohm 13, 14 / 23, 24 NO contact forceguided DC 110 V 01 A 10 ma 22 W > > (DC 24 V / 10 ma) > (DC 110 V / 01 A) 200 ma quickacting (13, 14) 200 ma quickacting (23, 24) X1, X2 Crimp bushings for strands without sleeve to 10 mm to 25 mm 2 IP65 95% 25 to +55 C 25 to +55 C T1 Category 1, class B mm 850 g without SIL2 SIL2 for soiling degree 2, overvoltage category II / 110 V 1, 2 AC 120 V / 125 khz 50 m 30 m Y1, Y2 1k2 Ohm 400 Ohm 10 Ohm 10 m < 600 Ohm > 1k8 Ohm 13, 14 / 23, 24 NO contact forceguided DC 110 V 01 A 10 ma 22 W > > (DC 24 V / 10 ma) > (DC 110 V / 01 A) 200 ma quickacting (13, 14) 200 ma quickacting (23, 24) X1, X2 Crimp bushings for strands without sleeve to 10 mm to 25 mm 2 IP65 95% 25 to +55 C 25 to +55 C T1 Category 1, class B mm 850 g v10 Operating Instructions SGTRS 3X8 Page 15/15