Electronic Balance Ionizer STABLO-AP Service Manual

Size: px
Start display at page:

Download "Electronic Balance Ionizer STABLO-AP Service Manual"

Transcription

1 Jan Electronic Balance Ionizer STABLO-AP Service Manual Analytical & Measuring Instruments Division

2 This page is intentionally left blank.

3 Table of Contents 1. Precautions for Troubleshooting Preliminary Check Visual Check Handling Precautions Troubleshooting The [POWER] indicator does not illuminate The [ALARM] indicator illuminates The key switch does not function Other function Replacing Parts Disassembling the Case Assembling the Case Removing and Replacing Circuit Boards Replacing Electrode Probes Checking Functionality Maintenance Parts... 15

4 1. Precautions for Troubleshooting 1.1 Preliminary Check Before troubleshooting, check the following. (1) Is the AC power cord disconnected or damaged? (2) Is the AC adapter connected properly? 1.2 Visual Check Open the ionizer cover and visually check for any problems, such as broken cable connections or cut or short-circuited circuit board wiring patterns. 1.3 Handling Precautions Disconnect the AC adapter before opening the ionizer cover. Be careful to prevent injury when handling the electrode probe, which has a very sharp point.

5 2. Troubleshooting 2.1 The [POWER] indicator does not illuminate. [POWER] indicator is not illuminated Is the AC adapter fully inserted? Insert the AC adapter plug all the way in. Turn the power switch ON and OFF several times. Finished Use an electrical tester to verify that the adapter output is normal. (24 V) Is the adapter functioning normally? Replace the adapter with one that functions properly. Check the LED board connections (connector insertion and solder joints). Finished Replace all circuit boards. Replace individual circuit boards in the following sequence. (1) LED board (2) Interface board (3) Power board (4) CPU board Adjust the ion balance if the LED board was replaced. Note: Adjust the trimmer to the same angle. The transformer is damaged. It must be repaired. Finished

6 2.2 The [ALARM] indicator illuminates. The [ALARM] indicator is illuminated. Is there debris or other contaminant near the electrode probes? Unplug the AC adapter and remove the debris or other contaminant. Turn the power switch ON and OFF several times. Finished Check for contact with the opposing electrode (connector insertion or solder joint) Finished Replace all circuit boards. Replace individual circuit boards in the following sequence. (1) LED board (2) Interface board (3) Power board (4) CPU board Adjust the ion balance if the LED board was replaced. Note: Adjust the trimmer to the same angle. The transformer is damaged. It must be repaired. Finished

7 2.3 The key switch does not function. The key switch does not Is there key stroke movement? Remove the upper cover. Remove the upper cover. Is there a clicking sensation when the button on the circuit board is pressed? Fit the button properly into the boss in the upper cover. Note: It only fits properly in the specified orientation. Is the LED connector fully inserted? Replace the power board. Fully insert the LED connector. Replace the LED board. Finished Finished Adjust the ion balance if the LED board was replaced. Note: Adjust the trimmer to the same angle. Finished

8 2.4 Other function.

9 3. Replacing Parts 3.1 Disassembling the Case 1) Remove three screws from the back of the ionizer case. Use a #0 Phillips screwdriver to unscrew the screw circled in yellow (20 mm long tapping screw with 2.6 mm nominal diameter) and a #1 Phillips screwdriver to unscrew the two screws circled in blue (16 mm long tapping screw with 3 mm nominal diameter). 2) Remove the upper cover. Note: There are tabs located near the area circled in red. Remove the upper cover carefully, being especially careful of the tabs. 3) Remove the LED board. Remove the board by gripping the top of the board and pulling it away from the cover, in the direction shown. 4) Place the ionizer on a flat surface and remove the one screw that fastens the circuit board assembly. Use a #0 Phillips screwdriver to remove the screw circled in red (6 mm long tapping screw with 3 mm nominal diameter).

10 5) Remove both the circuit boards and base together from the lower cover. Note 1: Remove both the circuit boards and base from the lower cover together at the same time. Note 2: They can be removed more easily by turning them upside down. Note 3: The thin metal electrode plate may be disconnected from the base. Be careful not to bend it. Also be careful not to cut your hand on its sharp edges. Note 4: Be careful not to poke or scratch yourself on the sharp metal needleshaped electrode probes that are installed on the base. 3.2 Assembling the Case 1) Temporarily secure the button. Note: Insert the button into the designated hole in the upper cover in the orientation that allows it to fit smoothly. Then temporarily secure it from the outside of the cover using masking tape or other means. 2) Insert the circuit boards and base into the lower cover. Note: Make sure that four base alignment bosses are fitted into the corresponding slots in the lower cover and the circuit board is fitted into its alignment slot.

11 3) Make sure the cable is not pinched in the lower cover. Note: Confirm that the cable is not next to the boss circled in red. If it is, use tweezers or other tool to move it away from the boss. 4) Screw the circuit board to the lower cover. Use a #0 Phillips screwdriver to fasten the screw circled in red (6 mm long tapping screw with 3 mm nominal diameter). 5) Install the LED board into the upper cover. Note: Press the edge of the LED board against the LED board mounting area on the upper cover. Then, with the edge pressed against the edge of the mounting surface, tilt the LED board and press into position.

12 6) Install the upper cover onto the lower cover. Note 1: Be careful of the cable routing from the LED board. Make sure the cable passes through the notch (circled in red) in the base. Note 2: Insert the upper cover by engaging the tabs, visually inspecting to make sure the cable is not pinched and there is no gap between the covers. 7) Fasten the three screws into the back of the ionizer case. Use a #0 Phillips screwdriver to fasten the screw circled in yellow (20 mm long tapping screw with 2.6 mm nominal diameter) and a #1 Phillips screwdriver to fasten the two screws circled in blue (16 mm long tapping screw with 3 mm nominal diameter). Remove the masking tape from the upper cover button and check if the button operates correctly. (It should have a clicking sensation.)

13 3.3 Removing and Replacing Circuit Boards 1) Remove the circuit boards and base from the lower cover, as described in ) First remove the interface board from the other boards, being careful not to damage the connector that connects the boards. Interface board 3) Then remove the power board by loosening one screw and carefully disconnecting the connector between the boards. Power board

14 Note: The discharge electrode plate and electrode probes are connected to the power board via a cable and connector. 4) Disconnect the LED board from the CPU board. The LED board is connected to the CPU board via a cable and connector. CPU board LED board 5) Replace the board that needs to be replaced and reassemble the boards by reversing the steps above. 6) Install the circuit boards and base into the lower cover, as described in 3.2. Note: Precautions for Replacing Circuit Boards To reduce the number of adjustment labor hours, method A is recommended for replacing circuit boards. A. Not Replacing the LED Board 1. Use the maintenance part ( ) to replace everything except the new LED board (dispose of the new LED board). B. Replacing the LED Board. 1. Remove the old LED board from the main STABLO unit and other circuit boards. 2. Measure the resistance values between H501 and H502 on the old LED board. (Record the result as value A. Measure up to XX kω, or 4.51 kω, for example.) 3. Measure the resistance values between H502 and H506 on the old LED board. (Record the result as value B, measuring up to XX kω or about kω.) 4. Measure the resistance values between H502 and H506 on the new board. (Record the result as value C, measuring up to XX kω or kω, for example.)

15 5. Adjust the trimmer value on the new board to the value determined by the calculation A/B C. Measure and adjust the resistance between H501 and H502 (to within an adjustment error of ±0.04 kω). (In this example, adjust the resistance to A/B C = 4.51/ = 4.74 kω.) H501 H502 H506 トリマ

16 3.4 Replacing Electrode Probes 1) Remove the circuit boards and base from the lower cover, as described in ) Pull out the electrode probe from the base. Note 1: Pull out the electrode probe by gripping it with needle nose pliers at the base of the probe. Note 2: Be careful of the sharp point on electrode probes. 3) Insert a new electrode probe. Note 1: Insert the electrode probe into the socket by gripping it with needle nose pliers on main shaft section of the probe. Note 2: When gripping an electrode probe with needle nose pliers or other tool, be sure to grip it along the shaft section of the probe. Gripping it on the tapered section could chip the electrode probe. Note 3: Insert electrode probes securely all the way in. 4) Check the tip of the inserted electrode probe. Note 1: Check the following two points. Check the electrode probe tip area for chips or bending. Confirm that the electrode probe tip is not excessively protruding or recessed. Note 2: If there is a problem with an electrode probe, replace it with a new one (only the probe with a problem). 5) Install the circuit boards and base into the lower cover, as described in 3.2.

17 4. Checking Functionality Confirm that the product functions properly after replacing a part. 1) Connect the ionizer to the power supply and confirm that the LED indicator illuminates. (If it does not illuminate, see 2. Troubleshooting and take necessary measures.) 2-1) Rub a sheet of fluoropolymer and nylon together and then use a quick static checker (P/N ) to confirm that the static charge at a perpendicular distance of 30 mm from the fluoropolymer sheet is about -5 kv. If inadequate, rub the sheets together again. (Static charge does not develop as readily if both sheet surfaces are not clean. In that case, resolve the problem by cleaning both sheet surfaces with alcohol.) 2-2) Then operate the ionizer unit for five seconds at a perpendicular distance of 30 mm from the fluoropolymer sheet, moving the ionizer as though it was spraying the entire sheet surface with mist. The purpose of moving the ionizer is to remove the static charge uniformly from the entire fluoropolymer sheet. 2-3) Then use the quick static checker (P/N ) again to confirm that the static charge at a perpendicular distance of 30 mm from the fluoropolymer sheet is about -300 V. 2-4) If the value is inappropriate, repeat the test. Then if there is a problem, see 2. Troubleshooting.)

18 5. Maintenance Parts No. P/N Description Remarks Brush BRUSH Dedicated AC Adapter AC ADAPTER,ATS024-P Electrode Probe ELECTRODE PROBE Sold individually (seven probes used) Circuit board unit CIRCUIT BOARD UNIT Jig, PTFE JIG, PTFE Jig, NYLON JIG, NYLON Static-E tester STATIC-E TESTER Cable assy, ionizer CABLE ASSY, IONIZER Caution label CAUTION LABEL

HP Pavilion dv7-6c90us Cooling fan Replacement

HP Pavilion dv7-6c90us Cooling fan Replacement HP Pavilion dv7-6c90us Cooling fan Replacement This guide will walk you through the process of replacing the cooling fan in an HP Pavilion dv7 laptop. Written By: Angelina Clayton ifixit CC BY-NC-SA www.ifixit.com

More information

Plasma Panel Replacement Guide DU-42PX12X

Plasma Panel Replacement Guide DU-42PX12X Plasma Panel Replacement Guide DU-42PX12X Panel Replacement: At this point, the panel has been determined to be defective and replacement is necessary. Upon receiving the replacement panel, it must be

More information

Chapter 4 Replacement Procedures

Chapter 4 Replacement Procedures Chapter 4 Replacement Procedures 4 4-ii Satellite P30 Series Maintenance Manual Chapter 4 Contents 4.1 General... 4-1 4.2 Battery... 4-7 4.3 PC Card... 4-8 4.4 HDD... 4-10 4.5 Optical Drive Module... 4-12

More information

RSL PSM-2 Power Supply Module Project: Modifying a FlatCap2

RSL PSM-2 Power Supply Module Project: Modifying a FlatCap2 RSL PSM-2 Power Supply Module Project: Modifying a FlatCap2 Dear Do-It-Yourselfer, The stock FlatCap2 is less than a stellar performer. Used with a CD5 CD player, for example, it gives flabby bass control,

More information

4.1 General. 4 Replacement Procedures

4.1 General. 4 Replacement Procedures 4.1 General This chapter explains how to disassemble the computer and replace Field Replaceable Units (FRUs). It may not be necessary to remove all the FRUs in order to replace one. The chart below is

More information

Welch Allyn Connex Vital Signs Monitor 6000 Power Supply Replacement

Welch Allyn Connex Vital Signs Monitor 6000 Power Supply Replacement Welch Allyn Connex Vital Signs Monitor 6000 Power Supply Replacement Replace the power supply in a 6000 series Welch Allyn Connex Vital Signs Monitor. Written By: Sam Lionheart ifixit CC BY-NC-SA www.ifixit.com

More information

How to Assemble a Desktop PC

How to Assemble a Desktop PC How to Assemble a Desktop PC By Taylor Koch iii Table of Contents Introduction to Building a Desktop PC... 1 Preparation and Precautions... 3 PC Parts... 3 Basic Tools... 3 Safety Precautions... 3 Installing

More information

Written By: Charlie Mohr

Written By: Charlie Mohr NEC LCD1770NX Capacitor Replacement Replacement of a capacitor on the power supply circuit board. Written By: Charlie Mohr ifixit CC BY-NC-SA www.ifixit.com Page 1 of 14 INTRODUCTION There are many capacitors

More information

CINTENNA ANTENNA REPAIR GUIDE

CINTENNA ANTENNA REPAIR GUIDE The Cintenna is a great tool when looking to transmit WIRELESS DMX data over obstacles or hard to reach places. Wireless DMX can have its issues when not having a good line of sight between the transmitter

More information

Phillips Screwdriver. Some C-128's may need a TORX ("star" point) driver (size T10)f available at Sears, and other hardware and automotive stores.

Phillips Screwdriver. Some C-128's may need a TORX (star point) driver (size T10)f available at Sears, and other hardware and automotive stores. C-128 INSTALLATION Required Tools: Phillips Screwdriver. Some C-128's may need a TORX ("star" point) driver (size T10)f available at Sears, and other hardware and automotive stores. IC extractor or small,

More information

2015 SIMMCONN LABS, LLC. All rights reserved. NewScope-T1 Operation Manual

2015 SIMMCONN LABS, LLC. All rights reserved. NewScope-T1 Operation Manual 2015 SIMMCONN LABS, LLC. All rights reserved NewScope-T1 Operation Manual April 12, 2017 NewScope-T1 Operation Manual 1 Introduction... 3 2 Installation... 4 2.1 Initial Inspection... 4 2.2 Installation

More information

Written By: Walter Galan

Written By: Walter Galan Replace a cracked screen on your iphone 4S. Written By: Walter Galan ifixit CC BY-NC-SA www.ifixit.com Page 1 of 32 INTRODUCTION Use this guide to replace the screen on your iphone 4S. After successfully

More information

Replacement Keyswitch Assembly

Replacement Keyswitch Assembly Installation Instructions Replacement Keyswitch Assembly (Catalog No. 2711E-NKSW1) Applicable Terminals Use this replacement keyswitch with PanelView Terminals 2711-KA1, -KC1, -TA1, -TC1, -TA4, -TC4 and

More information

imac Intel 21.5" EMC 2389 Stand Replacement

imac Intel 21.5 EMC 2389 Stand Replacement imac Intel 21.5" EMC 2389 Stand Replacement Replace a broken or cosmetically unappealing stand on the imac 2389 21.5 Written By: Aaron Cooke ifixit CC BY-NC-SA www.ifixit.com Page 1 of 30 INTRODUCTION

More information

OnePlus 5 Screen and Digitizer Assembly Replacement

OnePlus 5 Screen and Digitizer Assembly Replacement OnePlus 5 Screen and Digitizer Assembly Replacement Follow this guide to replace the screen and digitizer for the OnePlus 5. This replaces the screen as well as the frame it is attached to. Written By:

More information

Z-Truck (Vertical Moving) Z-truck Flag. Y-Truck (Horizontal Moving) FIGURE 1: VIEW OF THE Z-TRUCK. Flexshaft Assembly

Z-Truck (Vertical Moving) Z-truck Flag. Y-Truck (Horizontal Moving) FIGURE 1: VIEW OF THE Z-TRUCK. Flexshaft Assembly Replacing the LCD Cable To remove and replace the LCD Cable you will need the following tools: #2 Phillips screwdriver (magnetic tip preferred) Socket wrench with 10mm socket Removing the Side Panel 1.

More information

Canon EOS Rebel T2i Top Cover Replacement

Canon EOS Rebel T2i Top Cover Replacement Canon EOS Rebel T2i Top Cover Replacement Replacing the top piece of a Canon T2i (550D). In my case, I had a broken hot-shoe, but as most controls on this camera are built into the same part, this repair

More information

Replacing the Hardware Configuration Option EPROM on the 1822

Replacing the Hardware Configuration Option EPROM on the 1822 MPMS Service Note 1014-806 Replacing the Hardware Configuration Option EPROM on the 1822 When you install an MPMS option, you will use these procedures to replace the hardware configuration option EPROM

More information

Replacing the PanelMate Power Pro 1785 Series, PanelMate epro 7585x-8 and 7685x-8 Series Backlight Assembly

Replacing the PanelMate Power Pro 1785 Series, PanelMate epro 7585x-8 and 7685x-8 Series Backlight Assembly Replacing the PanelMate Power Pro 1785 Series, PanelMate epro 7585x-8 and 7685x-8 Series Assembly Introduction The Replacement Kit provides a replacement backlight for the PanelMate Power Pro 1785 Series,

More information

Gateway Profile 4 service guide

Gateway Profile 4 service guide Gateway Profile 4 service guide Customizing Troubleshooting Contents Replacing Components in Your Gateway Profile 4.................. 1 About this guide.....................................................

More information

apple Service Source PowerBook G4 Updated 8 July Apple Computer, Inc. All rights reserved.

apple Service Source PowerBook G4 Updated 8 July Apple Computer, Inc. All rights reserved. apple Service Source PowerBook G4 Updated 8 July 2003 2003 Apple Computer, Inc. All rights reserved. apple Service Source Take Apart PowerBook G4 2003 Apple Computer, Inc. All rights reserved. apple PowerBook

More information

To connect the AC adapter:

To connect the AC adapter: Replacing the AC Adapter Replacing the AC Adapter 3 Plug the power cord into a wall outlet. The power indicator turns on. To connect the AC adapter: Connect the power cord to the AC adapter. Power indicator

More information

Quicksilver 606 TR-606 CPU Upgrade

Quicksilver 606 TR-606 CPU Upgrade Quicksilver 606 TR-606 CPU Upgrade D650C 128 Installation Guide Social Entropy Electronic Music Instruments TABLE OF CONTENTS WARNINGS... 1 OVERVIEW... 2 WHAT'S IN THE BOX... 3 OPENING THE TR-606 CASE...

More information

imac Intel 27" EMC 2639 Hard Drive

imac Intel 27 EMC 2639 Hard Drive imac Intel 27" EMC 2639 Hard Drive Replacement Replace the Hard Drive in your imac Intel 27" EMC 2639. Written By: Walter Galan ifixit CC BY-NC-SA www.ifixit.com Page 1 of 26 INTRODUCTION Replacing the

More information

Dell Inspiron N5110 Service Manual

Dell Inspiron N5110 Service Manual Dell Inspiron N5110 Service Manual Regulatory model: P17F Regulatory type: P17F001 Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better use of your computer.

More information

Replacing the Galaxy II CRT Monitor with a Flat Screen Monitor Kit # 42638

Replacing the Galaxy II CRT Monitor with a Flat Screen Monitor Kit # 42638 Replacing the Galaxy II CRT Monitor with a Flat Screen Monitor Kit # 42638 This kit contains detailed instructions on removing a Galaxy II Daewoo monitor and replacing it with a 19 wide flat screen monitor.

More information

Live emate repair at WWNC.

Live emate repair at WWNC. Live emate repair at WWNC Frank Gründel http://www.pda-soft.de A word about me Frank Gründel alias Frank Gruendel Approx. 45 years old Married to an amazing wife One child Hardware developer for 15 years

More information

Written By: Colin Glaves

Written By: Colin Glaves Written By: Colin Glaves ifixit CC BY-NC-SA www.ifixit.com Page 1 of 9 INTRODUCTION Please try our Troubleshooting Guide prior to replacing your Display Assembly. This guide covers the detachment and assembly

More information

E1135C PDU and Pod Upgrade Procedure

E1135C PDU and Pod Upgrade Procedure E4030-90010 Rev. B 12/2003 In this Document... Tools Needed, 2 Contents of the Upgrade Kits, 2 Installation Procedures, 4 Verifying the Power Option of the New PDU, 4 Removing the PDU from the Support

More information

GL2200 MIXING CONSOLE

GL2200 MIXING CONSOLE GL2200 MIXING CONSOLE SYS-LINK EXPANDER OPTION This option connects a GL2200 console as a channel expander to a second console with just one or two interconnecting cables. Kit GL2200-SL1 = SINGLE Single

More information

4.1 Parts and Components... IV Assembly Tips... IV Assembly Precautions... IV Required Tools, Equipment and Materials..

4.1 Parts and Components... IV Assembly Tips... IV Assembly Precautions... IV Required Tools, Equipment and Materials.. IV PERSONALITY MODULE ASSEMBLY 4.1 Parts and Components............ IV-1 4.2 Assembly Tips............... IV-1 4.3 Assembly Precautions............ IV-1 4.4 Required Tools, Equipment and Materials.. IV-1

More information

imac Intel 27" Retina 5K Display CPU Replacement

imac Intel 27 Retina 5K Display CPU Replacement imac Intel 27" Retina 5K Display CPU Replacement Replace or upgrade the CPU in your imac Intel 27" Retina 5K Display. Written By: Sam Lionheart ifixit CC BY-NC-SA www.ifixit.com Page 1 of 36 INTRODUCTION

More information

Encore XT Manual Gun Upgrade Kit

Encore XT Manual Gun Upgrade Kit Instruction Sheet P/N 1600823-01 Encore XT Manual Gun Upgrade Kit 1600834 Introduction Follow these instructions to upgrade your Encore manual spray gun to the improved design of the Encore XT spray gun.

More information

Upgrading and Servicing Guide

Upgrading and Servicing Guide Upgrading and Servicing Guide The information in this document is subject to change without notice. Hewlett-Packard Company makes no warranty of any kind with regard to this material, including, but not

More information

Removing and Replacing Parts

Removing and Replacing Parts Removing and Replacing Parts Preparing to Work Inside the Computer Recommended Tools Screw Identification System Components Hard Drive Fixed Optical Drive Media Bay Devices Memory Modules Mini PCI Card

More information

GPIB-232CT-A IBCL EPROM Installation Guide

GPIB-232CT-A IBCL EPROM Installation Guide NATIONAL INSTRUMENTS The Software is the Instrument Installation Guide GPIB-232CT-A IBCL EPROM Installation Guide This guide describes how to replace the factory-installed EPROM that comes with your GPIB-232CT-A.

More information

Removal and Installation8

Removal and Installation8 8 Screw Types 8-4 Top Cover Assembly 8-5 Left Hand Cover 8-6 Right Hand Cover 8-10 Front Panel Assembly 8-14 Left Rear Cover 8-15 Right Rear Cover 8-16 Extension Cover (60" Model only) 8-17 Media Lever

More information

ASUS D550MA-DS01 Screen Replacement

ASUS D550MA-DS01 Screen Replacement ASUS D550MA-DS01 Screen Replacement This guide will show you how to replace your laptop screen. Written By: Calvin Wieczorek ifixit CC BY-NC-SA www.ifixit.com Page 1 of 12 INTRODUCTION Many people will

More information

TCM-4 Data Logger Battery Replacement Instructions

TCM-4 Data Logger Battery Replacement Instructions TCM-4 Data Logger Battery Replacement Instructions These instructions apply to the following product: TCM-4 Shallow Water Current Meter These instructions assume that the user has purchased a TCM-4 Battery

More information

Upgrade Instructions. P/N Revision A. October Printer Terminal Holder * *

Upgrade Instructions. P/N Revision A. October Printer Terminal Holder * * Upgrade Instructions P/N 96-08-0 Revision A October 000 480 Printer Terminal Holder P/N 96-08-0 Revision A *96080* Instructions This terminal holder connects the INTERMEC R 600 Series and 700 Series Computers

More information

Written By: Andrew Bookholt

Written By: Andrew Bookholt Replace a dead logic board in your iphone 4 Verizon. Written By: Andrew Bookholt ifixit CC BY-NC-SA www.ifixit.com Page 1 of 17 INTRODUCTION Use this guide to replace your iphone's logic board. TOOLS:

More information

iphone 6 Plus Front Facing Camera and Sensor Assembly Replacement

iphone 6 Plus Front Facing Camera and Sensor Assembly Replacement iphone 6 Plus Front Facing Camera and Sensor Assembly Replacement Replace the Front-Facing Camera and Sensor Assembly in your iphone 6 Plus. Written By: Walter Galan ifixit CC BY-NC-SA www.ifixit.com Page

More information

Dell OptiPlex All-in-One. Stand Installation Guide

Dell OptiPlex All-in-One. Stand Installation Guide Dell OptiPlex All-in-One Stand Installation Guide Notes, cautions, and warnings NOTE: A NOTE indicates important information that helps you make better use of your product. CAUTION: A CAUTION indicates

More information

iphone 4 Verizon Headphone Jack Cable Replacement

iphone 4 Verizon Headphone Jack Cable Replacement iphone 4 Verizon Headphone Jack Cable Replacement Replace a broken headphone jack cable that contains the upper microphone as well as the electronic portions of the volume buttons and silent switch on

More information

Chapter 2: Disassembly

Chapter 2: Disassembly P370EM / P370EM3 Chapter 2: Overview This chapter provides step-by-step instructions for disassembling the P370EM / P370EM3 series notebook s parts and subsystems. When it comes to reassembly, reverse

More information

Richter Optica. Instructions for Model: MDS2 Middle School Microscope

Richter Optica. Instructions for Model: MDS2 Middle School Microscope Richter Optica info@richter-optica.com Instructions for Model: MDS2 Middle School Microscope Eyepiece 360 Rotatable Head Revolving Nosepiece Carrying Handle Objectives Rack Stop Stage Stage Clips Disc

More information

Installing a Power over Ethernet injector

Installing a Power over Ethernet injector Installing a Power over Ethernet injector AlphaEclipse StreetSmart and RoadStar signs The instructions in this document explain how to install/replace a Power over Ethernet (PoE) injector in a StreetSmart

More information

Elecraft K3 KREF3 Output Level Modification

Elecraft K3 KREF3 Output Level Modification Elecraft K3 Revision A, September 15, 2015 Copyright 2015, Elecraft, Inc. All Rights Reserved Introduction This modification increases the output levels from the KREF3 Reference Oscillator to provide proper

More information

Chapter 4 Replacement Procedures

Chapter 4 Replacement Procedures Chapter 4 Replacement Procedures 4 Replacement Procedures 4 4-ii Portege M200 Maintenance Manual (960-457) 4 Replacement Procedures Chapter 4 Contents 4.1 Overview... 4-1 Safety Precautions... 4-2 Before

More information

*E * E E0606

*E * E E0606 75000 SERIES B Instrument BASIC Installation Note Copyright Agilent Technologies, Inc., 1990-2006 *E1300-90020* E1300-90020 E0606 Manual Part Number: E1300-90020 Printed: June 2006 Edition 1 Rev 2 Microfiche

More information

Written By: Sam Lionheart

Written By: Sam Lionheart iphone 5s Earpiece Speaker Replacement Replace the earpiece speaker in an iphone 5s. Written By: Sam Lionheart ifixit CC BY-NC-SA www.ifixit.com Page 1 of 22 INTRODUCTION Use this guide to replace a broken

More information

CAMERA ASSEMBLY. Removal/Replacement of the Camera Box Assembly APR-CA. Install Camera Assembly. Remove Camera Assembly

CAMERA ASSEMBLY. Removal/Replacement of the Camera Box Assembly APR-CA. Install Camera Assembly. Remove Camera Assembly CAMERA ASSEMBLY Removal/Replacement of the Camera Box Assembly APR-CA REQUIRED TOOLS: 9/64 hex key Small flat-tip screwdriver Remove Camera Assembly camera 1. Locate the camera assembly underneath the

More information

A how-to guide for replacing the DJI Phantom 4 body shell. *Replacing the body shell could also be used as a tear-down guide. Written By: GotMac

A how-to guide for replacing the DJI Phantom 4 body shell. *Replacing the body shell could also be used as a tear-down guide. Written By: GotMac A how-to guide for replacing the DJI Phantom 4 body shell. *Replacing the body shell could also be used as a tear-down guide. Written By: GotMac ifixit CC BY-NC-SA www.ifixit.com Page 1 of 15 INTRODUCTION

More information

edrive RAM Battery Alternate Replacement Procedure

edrive RAM Battery Alternate Replacement Procedure edrive RAM Battery Summary This technical note describes the process for replacing the TINI RAM battery with a higher capacity battery. With the edrive turned on, the external battery can be changed without

More information

NewScope-T0 Operation Manual

NewScope-T0 Operation Manual 2014 SIMMCONN LABS, LLC. All rights reserved NewScope-T0 Operation Manual Including NewScope-T0 and NewScope-T0e February 26, 2017 NewScope-T0 Operation Manual 1 Introduction... 3 2 Installation... 4 2.1

More information

WEASEL N/B MAINTENANCE

WEASEL N/B MAINTENANCE 2. System Assembly & Disassembly 2.1 System View 2.1.1 Front View ❶ Microphone Connector ❷ Audio Input Connector ❸ Audio Output Connector ❹ Top Cover Latch ❹ ❶ ❸ ❷ 2.1.2 Left-Side View ❶ VGA Port ❷ S-Video

More information

TABLE OF CONTENTS SECTION 1 TABLETOP CONFIGURATION SECTION 2 TABLETOP CONFIGURATION ACCESSORIES SECTION 3 SLIDE CONFIGURATION

TABLE OF CONTENTS SECTION 1 TABLETOP CONFIGURATION SECTION 2 TABLETOP CONFIGURATION ACCESSORIES SECTION 3 SLIDE CONFIGURATION S6 USER S MANUAL TABLE OF CONTENTS SECTION 1 TABLETOP CONFIGURATION SECTION 2 TABLETOP CONFIGURATION ACCESSORIES SECTION 3 SLIDE CONFIGURATION SECTION 4 SLIDE CONFIGURATION ACCESSORIES SECTION 5 RACK MOUNT

More information

Power Supply, 17-inch

Power Supply, 17-inch apple imac G5 Power Supply, 17-inch Replacement Instructions Follow the instructions in this sheet carefully. Failure to follow these instructions could damage your equipment and void its warranty. Note:

More information

iphone 6s Front Panel Replacement

iphone 6s Front Panel Replacement iphone 6s Front Panel Replacement Note: DIY at your own risk. New beginner must be careful, screens got problems mostly due to wrong installation process. INTRODUCTION Use this guide to replace a cracked

More information

Written By: Walter Galan

Written By: Walter Galan iphone 6 Plus Front Panel Replacement Replace the Front Panel in your iphone 6 Plus. Written By: Walter Galan ifixit CC BY-NC-SA www.ifixit.com Page 1 of 27 INTRODUCTION Use this guide to strip and replace

More information

Installing imac Intel 27" EMC 2390 Dual HDD or

Installing imac Intel 27 EMC 2390 Dual HDD or Installing imac Intel 27" EMC 2390 Dual HDD or SSD Drive Installing a secondary HDD or SSD in the mid 2010 27" imac EMC 2390. Written By: Brett Hartt ifixit CC BY-NC-SA www.ifixit.com Page 1 of 23 INTRODUCTION

More information

Texas Instruments TI-92 Screen Cover

Texas Instruments TI-92 Screen Cover Texas Instruments TI-92 Screen Cover Replacement Written By: Daniel Maldonado ifixit CC BY-NC-SA www.ifixit.com Page 1 of 10 INTRODUCTION In this guide we will show how to access and remove the plastic

More information

imac Intel 21.5" Retina 4K Display (2017) RAM

imac Intel 21.5 Retina 4K Display (2017) RAM imac Intel 21.5" Retina 4K Display (2017) RAM Replacement Learn how to replace or upgrade the RAM in your 2017 Retina 4K imac. Written By: Evan Noronha ifixit CC BY-NC-SA www.ifixit.com Page 1 of 38 INTRODUCTION

More information

iphone 4 Verizon Earpiece Speaker Replacement

iphone 4 Verizon Earpiece Speaker Replacement iphone 4 Verizon Earpiece Speaker Replacement Replace a blown-out earpiece speaker in your iphone 4 Verizon. Written By: Andrew Bookholt ifixit CC BY-NC-SA www.ifixit.com Page 1 of 18 INTRODUCTION Use

More information

Upgrading and Servicing Guide

Upgrading and Servicing Guide Upgrading and Servicing Guide The only warranties for Hewlett-Packard products and services are set forth in the express statements accompanying such products and services. Nothing herein should be construed

More information

Replacing the RAID Battery Backup Unit Assembly on Series 3 FireSIGHT 3500 Defense Centers, Version 5.x

Replacing the RAID Battery Backup Unit Assembly on Series 3 FireSIGHT 3500 Defense Centers, Version 5.x Replacing the RAID Battery Backup Unit Assembly on Series 3 FireSIGHT 3500 Defense Centers, Version 5.x Last Updated: December 4, 2014 Use these instructions to replace the RAID battery backup unit (BBU)

More information

Phase Loss Protection Upgrade. Phase Loss Protection Upgrade. In this bulletin:

Phase Loss Protection Upgrade. Phase Loss Protection Upgrade. In this bulletin: Phase Loss Protection Upgrade In this bulletin: Introduction... 2 Purpose... 2 General... 2 Applicability... 2 HD3070 Phase Loss Protection Upgrade Kit Parts... 2 Preparation... 4 Install the Phase Loss

More information

Microscope with original illuminator. Microscope with Nanodyne replacement illuminator.

Microscope with original illuminator. Microscope with Nanodyne replacement illuminator. Nanodyne Replacement Illuminator for Zeiss xioskop Microscope Microscope with original illuminator. Microscope with Nanodyne replacement illuminator. Copyright 09 Nanodyne Measurement Systems. Document

More information

Written By: Andrew Bookholt

Written By: Andrew Bookholt iphone 4 Rear Camera Replacement Removing your iphone 4's 5 MP rear camera. Written By: Andrew Bookholt ifixit CC BY-NC-SA www.ifixit.com Page 1 of 10 INTRODUCTION Use this guide to remove the iphone's

More information

imac Intel 21.5" EMC 2638 RAM Replacement

imac Intel 21.5 EMC 2638 RAM Replacement imac Intel 21.5" EMC 2638 RAM Replacement Replace the RAM in your imac Intel 21.5" EMC 2638. Written By: Walter Galan ifixit CC BY-NC-SA www.ifixit.com Page 1 of 33 INTRODUCTION Use this guide to replace

More information

HTC RE Companion Handheld camera

HTC RE Companion Handheld camera HTC RE Companion Handheld camera disassemby HTC RE Companion camera disassembly starting point. This will get the camera open with minimal damage, and give you some options to repair. Written By: Mike

More information

GbX Backplane and Daughtercard Tooling. *GbX is a Trademark of Teradyne Inc.

GbX Backplane and Daughtercard Tooling. *GbX is a Trademark of Teradyne Inc. GbX BACKPLANE and DAUGHTERCARD INSTALLATION TOOLING For GbX Connector Series 75220 and 75360 (4 Pair and 5 Pair Daughtercard assemblies) 75292 (Daughtercard Power) 75235 and 75237 (4 Pair and 5 Pair Backplane

More information

Apple 3.5 Drive External Floppy Drive

Apple 3.5 Drive External Floppy Drive Apple 3.5 Drive External Floppy Drive Teardown This guide will show the disassembly down to the bare internal drive and other components of the Apple 3.5 Drive. Written By: rockinkat ifixit CC BY-NC-SA

More information

Apex Tablet 7 Battery Replacement

Apex Tablet 7 Battery Replacement Apex Tablet 7 Battery Replacement This guide will instruct you on how to replace the lithium-ion battery inside the Apex 7" Tablet. Written By: Corrine Nief ifixit CC BY-NC-SA www.ifixit.com Page 1 of

More information

imac Intel 27" EMC 2546 Adhesive Strips

imac Intel 27 EMC 2546 Adhesive Strips imac Intel 27" EMC 2546 Adhesive Strips Replacement Reattach your display with a set of adhesive foam strips. Written By: Andrew Optimus Goldberg ifixit CC BY-NC-SA www.ifixit.com Page 1 of 18 INTRODUCTION

More information

Olympus BX43 and BX46 Installation Instruction for Microscope End Users (easy install version) 4

Olympus BX43 and BX46 Installation Instruction for Microscope End Users (easy install version) 4 Olympus X and X6 Installation Instruction for Microscope End Users (easy install version) PN 07 Olympus X_6 Illuminator ssy dditional Items Included ut Not Shown: PN 077 Hex Key mm PN 060 Hex Key mm M

More information

iphone 6 Plus 5GHz Wi-Fi Antenna Replacement

iphone 6 Plus 5GHz Wi-Fi Antenna Replacement iphone 6 Plus 5GHz Wi-Fi Antenna Replacement Replace the 5GHz Wi-Fi antenna in your iphone 6 Plus. Written By: Walter Galan ifixit CC BY-NC-SA www.ifixit.com Page 1 of 19 INTRODUCTION Use this guide to

More information

FITTING INSTRUCTIONS

FITTING INSTRUCTIONS & This option connects a GL3000 or GL3300 console as a channel expander to a second console with just one or two interconnecting cables. Kit Part No: GL3000-SL1 Single option to install SYS-LINK to one

More information

Elecraft K3 KPA3 Power Connector Replacement Revision B, June 30, 2017 Copyright 2017, Elecraft, Inc. All Rights Reserved

Elecraft K3 KPA3 Power Connector Replacement Revision B, June 30, 2017 Copyright 2017, Elecraft, Inc. All Rights Reserved Introduction Elecraft K3 KPA3 Power Connector Replacement Revision B, June 30, 2017 Copyright 2017, Elecraft, Inc. All Rights Reserved The connectors furnishing high current to the KPA3 module have failed

More information

Toshiba Satellite A210 Motherboard

Toshiba Satellite A210 Motherboard Toshiba Satellite A210 Motherboard Replacement In this guide you will learn how to properly remove the Motherboard. Written By: Devin ifixit CC BY-NC-SA www.ifixit.com Page 1 of 12 INTRODUCTION Before

More information

NewScope-7B Operating Manual

NewScope-7B Operating Manual 2016 SIMMCONN Labs, LLC All rights reserved NewScope-7B Operating Manual Preliminary May 13, 2017 NewScope-7B Operating Manual 1 Introduction... 3 1.1 Kit compatibility... 3 2 Initial Inspection... 4 3

More information

Mac mini Mid 2010 IR Sensor Replacement

Mac mini Mid 2010 IR Sensor Replacement Replace a broken IR sensor/sleep LED. Written By: Andrew Bookholt ifixit CC BY-NC-SA www.ifixit.com Page 1 of 18 INTRODUCTION Use this guide to replace your mini's IR sensor/sleep LED assembly. Replacing

More information

Peel & Present Option Rev.C

Peel & Present Option Rev.C Peel & Present Option 92-2479-01 Rev.C Contents of the Peel & Present Kit This kit contains the following items: Peel and Present Mechanism Assist Roller Bushing Follow the steps below to install these

More information

Mac mini Late 2014 Power Supply Replacement

Mac mini Late 2014 Power Supply Replacement Mac mini Late 2014 Power Supply Replacement Replace the power supply in a Late 2014 Mac mini. Written By: Sam Lionheart ifixit CC BY-NC-SA www.ifixit.com Page 1 of 19 INTRODUCTION Use this guide to replace

More information

Replacing Preamplifier Circuit Boards

Replacing Preamplifier Circuit Boards Instruction Guide Replacing Preamplifier Circuit Boards Before you begin This instruction sheet applies to the Plexon PBX-series preamplifiers. Use these instructions to expand, replace, or upgrade the

More information

Chapter 4 Replacement Procedures

Chapter 4 Replacement Procedures Chapter 4 Replacement Procedures 4 Replacement Procedures 4 4-ii Satellite A50/TECRA A2 Maintenance Manual (960-478) 4 Replacement Procedures Chapter 4 Contents 4.1 Overview...4-1 Safety Precautions...

More information

Written By: Evan Noronha

Written By: Evan Noronha Replace just the front panel not including the home button assembly, front-facing camera and sensor assembly, or earpiece speaker in an iphone 6s Plus. Written By: Evan Noronha ifixit CC BY-NC-SA www.ifixit.com

More information

Smart Multivariable Transmitter (SMV 3000) Electronics Module Replacement Kit Instruction

Smart Multivariable Transmitter (SMV 3000) Electronics Module Replacement Kit Instruction Smart Multivariable Transmitter (SMV 3000) Electronics Module Replacement Kit Instruction Electronics Module (Part number 51404208 503, -513) Document Form: 34-SM-33-01 Effective: 09-01 Supersedes: 34-SM-33-01,

More information

Samsung Galaxy S10 Motherboard

Samsung Galaxy S10 Motherboard Samsung Galaxy S10 Motherboard Replacement This guide shows how to remove the motherboard for the Galaxy S10. This assembly includes the USB-C charging port. Written By: Arthur Shi ifixit CC BY-NC-SA www.ifixit.com

More information

Dell XPS 14z Owner s Manual

Dell XPS 14z Owner s Manual Dell XPS 14z Owner s Manual Computer model: L412z Regulatory model: P24G series Regulatory type: P24G001 Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better

More information

Sony SLT Alpha-65V Flash Capacitor

Sony SLT Alpha-65V Flash Capacitor Sony SLT Alpha-65V Flash Capacitor Replacement How to replace the flash capacitor located on the left side of the camera. Written By: Dima Kyle ifixit CC BY-NC-SA www.ifixit.com Page 1 of 11 INTRODUCTION

More information

Moto G4 LCD Screen and Digitizer Assembly Replacement

Moto G4 LCD Screen and Digitizer Assembly Replacement Moto G4 LCD Screen and Digitizer Assembly Replacement Replace a cracked or faulty display as a complete assembly, including the surrounding frame/chassis. Written By: Richard Gonzalez ifixit CC BY-NC-SA

More information

Motion LE1700 Tablet PC Hard Disk Drive Upgrade Procedure

Motion LE1700 Tablet PC Hard Disk Drive Upgrade Procedure Motion LE1700 Tablet PC Hard Disk Drive Upgrade Procedure 2008 Motion Computing, Inc. All rights reserved. This document contains information protected by copyright. No part of this document may be reproduced

More information

Motorola Moto X Display Assembly

Motorola Moto X Display Assembly Motorola Moto X Display Assembly Replacement Replace the display assembly on a Motorola Moto X. Written By: Sam Lionheart ifixit CC BY-NC-SA www.ifixit.com Page 1 of 22 INTRODUCTION Shattered screen? Darn

More information

Liebert XDA Air Flow Enhancer. User Manual

Liebert XDA Air Flow Enhancer. User Manual Liebert XDA Air Flow Enhancer User Manual Technical Support Site If you encounter any installation or operational issues with your product, check the pertinent section of this manual to see if the issue

More information

3 1 ROM. Installation Manual

3 1 ROM. Installation Manual 3 1 ROM Installation Manual 3.1 ROM Installation Instructions Please read the following cartfully The following installation sequences should be performed by an authorised Amiga Technologies service centre,

More information

Written By: Walter Galan

Written By: Walter Galan imac Intel 21.5" EMC 2428 CPU Replacement Replace the CPU in your imac Intel 21.5" EMC 2428. Written By: Walter Galan ifixit CC BY-NC-SA www.ifixit.com Page 1 of 33 INTRODUCTION Use this guide to upgrade

More information

Escrito por: Andrew Bookholt

Escrito por: Andrew Bookholt Replace the exterior metal silent switch on your Verizon iphone 4. Escrito por: Andrew Bookholt ifixit CC BY-NC-SA es.ifixit.com Página 1 de 23 INTRODUCCIÓN Use this guide to replace the external metal

More information

ABM International, Inc. Lightning Stitch Checklist 9/13/2013

ABM International, Inc. Lightning Stitch Checklist 9/13/2013 ABM International, Inc. Lightning Stitch Checklist 9/13/2013 1) Piggy backed board assembly (1) Piggy back board assembly tested? Yes No 24v passed XB passed XA passed YB passed YA passed SAFE passed S/S

More information

How to Perform an IBM ThinkPad X60s Fan Spindle Replacement

How to Perform an IBM ThinkPad X60s Fan Spindle Replacement How to Perform an IBM ThinkPad X60s Fan Spindle Replacement This guide details an IBM ThinkPad X60s fan spindle replacement. Written By: Samuel Lees ifixit CC BY-NC-SA www.ifixit.com Page 1 of 10 INTRODUCTION

More information