The PM1000 series is a universal 4 digit LED plug-on display for transmitters with 4-20mA 2 wire output and fitted with DIN43650 connector.

Transcription

1 PM1000 SERIES PLUG-ON DISPLAY BRIGHT LED DISPLAY INDICATION RANGE -999 TO FITS TO DIN CONNECTOR PLUG-ON TO ANY TRANSMITTER WITH 4-20MA OUTPUT EASY TO SCALE ON SITE ROBUST DESIGN SET POINT OPTION The PM1000 series is a universal 4 digit LED plug-on display for transmitters with 4-20mA 2 wire output and fitted with DIN43650 connector. The plug-on display simply fits between the transmitter plug and connecting cable socket and is powered from the 4-20mA current loop signal of the transmitter. No additional power is required. Display settings are stored in non-volatile EEPROM, and can be easily modified through the menu using two programming buttons. Calibration parameters (zero, span, decimal point position, filter, and set-point level) can all be reprogrammed and stored and retained when power is removed. The display assembly inside the enclosure can be rotated through 90º steps, which will suit any mounting angle and simply installation. Model PM1000 is the standard version. An integral open-drain switch output is provided on model PM1001. This can be programmed to open or close at a set-point level. The output can then by used to trigger an alarm or provided external controller. Typical applications for the plug-on display include use on pressure, temperature, level, RH, or flow transmitters for local readout, alarm activation or control. Adaptations for custom connectors can be made and available on request. Fax: +44 (0) Tel: +44 (0) sales@esi-tec.com

2 PM1000 SERIES PLUG-ON DISPLAY SPECIFICATION DISPLAY: 4 digit red LED display, 7mm digit height. DISPLAY OUTPUT RANGE: -999 to 9999 INPUT SIGNAL: 4-20mA, 2 wire current loop. DISPLAY CALIBRATION: Factory set to display 4.00 to for 4-20mA input. ACCURACY: 0.2% of full-scale input +/- 1 digit POWER SUPPLY VOLTAGE: Requires 5 V or less from loop supply. ALLOWED LOOP CURRENT: Maximum 60mA. Above this automatic circuit protection is activated. DISPLAY SAMPLING RATE: 300mS to 25.5 S, adjustable filter setting from menu. OPEN DRAIN SWITCH OUTPUT: Model number PM1001 only: P type MOSFET switch. Maximum current source: 90mA, with automatic circuit protection. PROGRAMMING: Via two press buttons, menu assisted. Access to the programming buttons is made by removing front cover. MENU SELECTION: Zero adjustment: -999 to 9999 Span adjustment: 0 to 9999 Decimal point: 3 positions or off Filter: 0.3 to 25.5 second Over-range: On/Off Setpoint: -999 to 9999 Setpoint direction: Up/Down Settings stored in Non-volatile EEPROM ERROR MESSAGES: When over-range option is selected: HI is displayed when input is above 20mA LO is displayed when input is less than 4mA when over-range option is off: ErC6 is displayed when range -999 to 9999 is exceeded. TEMPERATURE RANGE: Operating: - 10 C to + 60 C Storage: - 30 C to + 80 C CASE MATERIAL: Moulded ABS plastic, Red Acrylic display widow, Nitrile seal. INGRESS PROTECTION TYPE: Splash-proof, enclosure sealed to IP65 ELECTRICAL CONNECTION: Plugs directly onto transmitters with 4-20 ma output and right-angle DIN (3-pin +earth) connector plug. DIMENSIONS (in mm) PROGRAMMING To setup display: Remove 4 screws and front cover to access programming buttons ORDER DETAILS State model number. Model No. PM1000 PM1001 Standard plug-on display. Plug-on display with single set point. ELECTRICAL CONNECTIONS Pin No. PM1000 PM supply +supply mA signal -supply 3 not connected open drain (P type switch) Connected through to transducer plug CALIBRATION All products manufactured by Ellison Sensors are calibrated using precision calibration equipment with traceability to international standards. Ellison Sensors operates a policy of continuous product development. We reserve the right to change specification without prior notice.

3 PM8000 SIMPLE TO USE PROCESS INDICATOR 3 1/2 DIGIT LED PROCESS METER WIDE RANGE OF SCALABILITY 4-20mA, 0-10 & 1-5V DC PROCESS SIGNALS EXCELLENT STABILITY/ACCURACY DUAL SLOPE ADC DECIMAL POINT DISPLAY Model shown PM8004 The PM8000 offers you a simple process indicator ideal for general monitoring applications. The wide range of scalability provided makes this panel meter suitable for displaying of many different physical variables such as temperature, pressure, weight, humidity etc. The 3digit red LED Display has an accuracy of 0.1% ± 1 count and accepts standard process signals of 4-20mA, 1-5V and 0-10V and many others. A regulated 24V (rated 30mA) or 10V (rated 50mA) sensor supply is readily available on the input connector which can be used to power an external sensor. Jumper switches can be used to select 10V or 24V. Detachable screw connectors are provided to allow easy maintenance and installation. Zero and Span can be finely trimmed with a multi-turn potentiometer. Dual slope integration is employed to give ±1999 count resolution for ±20mA or ±10V analogue input signals. A decimal point can be selected to appear where required by a push-on jumper switch. Optional features include variable display brightness control, remote decimal point selection using remote switching and an extra fixed zero digit to multiply the reading by 10. Sensor House, Wrexham Technology Park, Wrexham, LL13 7YP, Wales, UK

4 PM8000 SPECIFICATION DISPLAY: 4 digit red LED display, 14.2mm digit height. RESOLUTION: 1 in 2000 maximum over full range, with 3 1/2 Digit Display (0 to +/- 1999) INPUT SIGNAL: 4-20mA, 0+/-20mA, 0+/-1mA, 0-10Vdc,0+/-10Vdc, 1-5Vdc,...others possible on request. INPUT RESISTANCE: 13ohms for current input, 1 Mohms for voltage COMMON MODE REJECTION: 100dB 0-60Hz, 250V max ADC METHOD: Dual slope conversion SPEED OF RESPONSE: Display update: 2.5/sec ACCURACY: 0.10% of reading +/- 2 counts TEMPERATURE STABILITY: 100 ppm/ºc for span, 50 ppm/ºc fo zero OUTPUT FOR EXTERNAL SENSORS: 24Vdc or 10V ACCURACY OF THE EXCITATION SUPPLY: +/-20% accuracy CURRENT CAPACITY OF THE EXCITATION SUPPLY: 30mA for 24V, 50mA for 10V POWER SUPPLY: 110 or 240 Vac standard, 11 to 30Vdc as option. POWER CONSUMPTION: 4VA maximum TEMPERATURE RANGE: Operating: 0 C to + 50 C Storage: - 10 C to + 70 C HUMIDITY: 90% RH maximum at 40ºC, non-condensing ELECTROMAGNETIC-COMPATIBILTY: Emissions EN Immunity EN Certification CE marked ELECTRICAL CONNECTION: 4 way detachable screw terminal connector for conductor size 0.5 to 1.5mm BEZEL SIZE: 96mm wide x 48mm high (1/8 DIN) CUTOUT SIZE: 92mm wide x 45 mm high DEPTH BEHIND PANEL: 93 mm minimum required WEIGHT: 300 grams typically CASE MATERIAL: Black polycarbonate DIMENSIONS (in mm) ORDER DETAILS State model number. No options with this panel meter Model No. PM /2 Digit Scalable Process Meter CALIBRATION All products manufactured by Ellison Sensors are calibrated using precision calibration equipment with traceability to international standards. Ellison Sensors operates a policy of continuous product development. We reserve the right to change specification without prior notice. Sensor House, Wrexham Technology Park, Wrexham, LL13 7YP, Wales, UK

5 PM8001 PM8002 PM MA, 0-10V & 0-5V DC & 1-5V PROCESS SIGNALS 3 1/2 & 4 1/2 DIGIT DISPLAY FORMATS EXCELLENT STABILITY/ACCURACY REGULATED SENSOR SUPPLY ZERO & SPAN ADJUSTMENTS LARGE RANGE OF OUTPUT FORMATS Model shown PM8004 OPTIONAL FEATURES The PM8001, PM8002 and PM8003 are an extremely versatile range of process meters providing the solution to most process monitor and readout needs. PM8001 has a 3digit display ranging from 0 to PM8001 and PM8002 have 4digit displays ranging from 0 to 19999, with accuracy of 0.05%. All have 14.2mm high, bright red LED readout as standard. Optional readout colours are available. Input signals options include 4-20mA, 0-10V, 1-5V and 0-5V, with other possible on request. Specify input type when ordering. Many output options are available in this range. These include analogue signal output for re-transmission, setpoint alarm relays, serial data output. Specify output type when ordering. Traditional screwdriver trimming potentiometers are used for calibration and alarm level setting on this product. This provides an uncomplicated, quick approach to setting operating parameters during installation.

6 PM8001 PM8002 PM8003 SPECIFICATION DISPLAY: High intensity red LED display, 14.2mm digit height. RESOLUTION: 3 1/2 Digit model PM /2 Digit models PM8002, PM8003 INPUT SIGNAL: 4-20mA, 0-10Vdc, 1-5Vdc, 0-5Vdc...others possible on request. INPUT RESISTANCE: 24ohms for current input, 1.1Mohms for voltage SPEED OF RESPONSE: Display update: 2.5/sec DECIMAL POINT SELECTION: Set position with push-on jumpers at rear ACCURACY: 0.05% of reading +/- 1 count PM8001 +/-10 counts PM8002/3 TEMPERATURE STABILITY: 50 ppm of range/ºc span and zero OUTPUT FOR EXTERNAL SENSORS: Selectable 10 or 24Vdc, regulated. Others possible, including constant current. ACCURACY OF THE EXCITATION SUPPLY: +/-5% accuracy. Stability is 50ppm/C typical CURRENT CAPACITY OF THE EXCITATION SUPPLY: 120mA for 10V, 30mA for 24V POWER SUPPLY: 110 or 230 Vac standard, 24Vac and 10 to 30Vdc as option. CURRENT CONSUMPTION: 8VA maximum TEMPERATURE RANGE: Operating: - 20 C to + 50 C Storage: - 40 C to + 70 C HUMIDITY: 90% RH maximum at 40ºC, non-condensing ELECTROMAGNETIC-COMPATIBILTY: Emissions EN Immunity EN Certification CE marked ELECTRICAL CONNECTION: 4 way detachable screw terminal connector for conductor size 0.5 to 1.5mm BEZEL SIZE: 96mm wide x 48mm high (1/8 DIN) CUTOUT SIZE: 92mm wide x 45 mm high DEPTH BEHIND PANEL: 125 mm minimum required WEIGHT: 550 grams typically CASE MATERIAL: UL 94V0 rated black ABS OPTIONS (spec): ANALOGUE OUTPUT DRIVE CAPACITY: 4-20mA into loads 0-500ohms. 0-10V into loads from 500ohms to Infinity ANALOGUE OUTPUT ISOLATION: 380V safety rated from power & earth, but not isolated from input stage ANALOGUE OUTPUT SPEED OF RESPONSE: 500 milliseconds. ANALOGUE OUTPUT ACCURACY: 0.05% of range ANALOGUE OUTPUT LINEARITY: 0.01% of range ALARM RELAYS: 2 SPCO relays with adjustable hysteresis. Set HIGH or LOW. De-energise on alarm for fail safe RELAY CURRENT RATING: 7A, resistive load. If driving inductive loads, MOV varistors are recommended RELAY VOLTAGE RATING: 250Vac, 24Vdc ALARM SET-POINT STABILITY: +/- 100 ppm/ºc typical ALARM SPEED OF RESPONSE: 15mS typical ALARM HYSTERESIS: 1 count (PM8001), 10 counts (PM8002/3) ALARM ANNUNCIATION: Red LED illuminates when relay de-energises SERIAL OUTPUT FORMAT: 1 start bit, 8 data bits, 1or more stop bits. ASCII data terminated with a carriage return BAUD RATE: Selectable 1200, 2400, 4800 or 9600 DIMENSIONS (in mm) ORDER DETAILS State model number, input signal and output option if required. Model No. PM8001 PM8002 PM /2 digits. 2 programmable alarms 4 1/2 digits. No alarms 4 1/2 digits. 2 programmable alarms OPTIONS Analogue Output. 4-20mA, 0-10Vdc, +/-5Vdc Alarm Output. 2 SPCO Relay Serial Output. RS232 CALIBRATION All products manufactured by Ellison Sensors are calibrated using precision calibration equipment with traceability to international standards. Ellison Sensors operates a policy of continuous product development. We reserve the right to change specification without prior notice.

7 PM mA, 0-10V, 1-5V & 0-10mA INPUT/ DISPLAY RANGES SIMPLE TO PROGRAM 8 PROGRAM MEMORY OPTION 5 DIGIT LED DISPLAY EXCELLENT STABILITY/ACCURACY ISOLATED 24Vdc SENSOR EXCITATION 10 POINT USER-DEFINED LINEARISATION DIRECT ACCESS MENU FUNCTIONS FOR CALIBRATION, ALARM SETTING AND MORE The PM8004 series of digital panel meters are the ideal solution for measurement display and control applications, and are well suited to the readout and display of physical properties such as pressure, strain, temperature, humidity and others. A MENU-FREE calibration system is employed with this panel meter design. This makes calibration and set-up of operating parameters very straightforward and radically simplifies this process compared with the usual complex menu arrangement used on most digital meters. In the PM8004 the menu is replaced by simple push buttons enabling the zero, span, analogue output or alarms to be adjusted via a button on the front of the panel. The 5 digit red LED display is standard, providing 1 in resolution and an accuracy of 0.05% of range. Inputs include 4-20mA, 0-10V, 1-5V and 0-10mA. A 24V sensor excitation supply is provided and can be used to power an external transmitter current loop. Additionally a linearisation feature is provided with10 user-defined points, which can be used to improve display accuracy with non-linear input signals. Standard features include: Peak and valley memories to record max/min readings and which can be viewed using the MAX/MIN button on the front panel or by using remote contact closure switches. Automatic zero-drift compensation used to cancel long-term drift caused by ageing and temperature change etc. Calibration counter and tamper detector, in which an internal totaliser counts each calibration. This is then stored in non-volatile memory, which cannot be reset, making this a useful function to track calibration history. Finally a reset command can be used to clear any stored data. As a safety precaution for stored data, a 'lock-out' switch has been incorporated into the design to ensure that if this switch is enabled, no data can be lost. Options include 2 or 4 programmable alarm relay outputs, analogue outputs for signal retransmission, RS232 serial or BCD outputs.

8 PM8004 SPECIFICATION DISPLAY: High intensity red LED display, 14.2mm digit height. RESOLUTION: 1 in maximum over full range, with 5 Digit Display ( ) INPUT SIGNAL: 4-20mA,0-10mA, 0-10Vdc, 1-5Vdc,...others possible on request. INPUT RESISTANCE: 33ohms for current input, 1.1Mohms for voltage SPEED OF RESPONSE: Display update: 2/sec FILTERING / SMOOTHING: Selectable time constant of 0 to 5 seconds ACCURACY: 0.05% of reading TEMPERATURE STABILITY: 50 ppm/ºc for span, 20/ºC for zero OUTPUT FOR EXTERNAL SENSORS: 24Vdc, isolated ACCURACY OF THE EXCITATION SUPPLY: +/-20% accuracy. CURRENT CAPACITY OF THE EXCITATION SUPPLY: 50mA for 24V POWER SUPPLY: 95 to 265 Vac standard, 11 to 30Vdc as option.. CURRENT CONSUMPTION: 8VA maximum TEMPERATURE RANGE: Operating: - 20 C to + 50 C Storage: - 40 C to + 70 C HUMIDITY: 90% RH maximum at 40ºC, non-condensing ELECTROMAGNETIC-COMPATIBILTY: Emissions EN Immunity EN Certification CE marked ELECTRICAL CONNECTION: 4 way detachable screw terminal connector for conductor size 0.5 to 1.5mm BEZEL SIZE: 96mm wide x 48mm high (1/8 DIN) CUTOUT SIZE: 92mm wide x 45 mm high DEPTH BEHIND PANEL: 125 mm minimum required WEIGHT: 300 grams typically CASE MATERIAL: UL 94V0 rated black ABS OPTIONS (spec): ANALOGUE OUTPUT DRIVE CAPACITY: 4-20mA into loads 0-500ohms. 0-10V into loads from 500ohms to Infinity ANALOGUE OUTPUT ISOLATION: 250V optically isolated ANALOGUE OUTPUT SPEED OF RESPONSE: 100 milliseconds. ANALOGUE OUTPUT ACCURACY: 0.1% of range ANALOGUE OUTPUT LINEARITY: 0.02% of range ALARM RELAYS: 2 or 4 SPCO relays with adjustable hysteresis. Set HIGH or LOW. De-energise on alarm for fail safe RELAY CURRENT RATING: 5A, resistive load. If driving inductive loads, MOV varistors are recommended RELAY VOLTAGE RATING: 250Vac, 24Vdc ALARM SET-POINT STABILITY: +/- 100 ppm/ºc typical ALARM SPEED OF RESPONSE: 15mS typical SERIAL OUTPUT FORMAT: 1 start bit, 8 data bits, 1 or more stop bits. ASCII data terminated with a carriage return BAUD RATE: Selectable 1200, 2400, 4800 or 9600 DIMENSIONS (in mm) ORDER DETAILS State model number, and option. MODEL NO. PM8004 PM8004-2AL PM8004-4AL PM8004-AN5V PM8004-AN10V PM8004-AN20 PM8004-RS232 PM8004-DIFF PM8004-BCD Standard, no alarms 2 programmable alarms 4 programmable alarms No alarms. 0-5Vdc external O/P No alarms. 0-10Vdc external O/P No alarms. 4-20mA external O/P No alarms. RS232 external O/P No alarms. 4-20mA diff. external O/P No alarms. BCD external O/P All models, up to 5 programmable digits. CALIBRATION All products manufactured by Ellison Sensors are calibrated using precision calibration equipment with traceability to international standards. Ellison Sensors operates a policy of continuous product development. We reserve the right to change specification without prior notice.

9 PM8005 PM mA, 0-10V, 1-5V etc PROCESS SIGNALS 5 DIGIT LED DISPLAY EXCELLENT STABILITY/ACCURACY DIRECT ACCESS MENU FUNCTIONS FOR CALIBRATION, ALARM SETTING AND MORE LARGE RANGE OF STANDARD FEATURES Model shown PM8004 The PM8005 and PM8006 digital panel meters are simplified versions of the popular PM8004 digital process meter family offering the same high performance standards as the PM8004 but with a trimmed down feature list. A MENU-FREE calibration system is employed with this panel meter design. This makes calibration and set-up of operating parameters very straightforward and radically simplifies this process compared with the usual menu arrangement used on most digital meters. The menu in this case is replaced by simple push buttons enabling zero, span, analogue output or alarms to be adjusted via a button on the front of the panel. The 5 digit red LED display is standard, providing +/ count resolution and an accuracy of 0.10% of range. Input signals include 4-20mA, 0-10V, 1-5V and 0-10mA. A 24V sensor excitation supply is provided and can be used to power an external transmitter current loop. Standard features include: digital signal filtering, automatic zero-drift compensation, last digit rounding (count by 1, 2, 5, 10, 20, 50), minimum (valley) and maximum (peek) reading memory, display taring, two set-point alarm relays with latching or adjustable hysteresis, calibration counter and taper detector.

10 PM8005 PM8006 SPECIFICATION DISPLAY: High intensity red LED display, 14.2mm digit height. RESOLUTION: +/ counts maximum over full range, with 5 Digit Display ( to ) INPUT SIGNAL: 4-20mA,0-10mA, 0-10Vdc, 1-5Vdc,...others possible on request. INPUT RESISTANCE: 33ohms for current input, 1.1Mohms for voltage SPEED OF RESPONSE: Display update: 2.5/sec FILTERING / SMOOTHING: Selectable time constant of 0 to 5 seconds ACCURACY: 0.1% of reading +/-2 counts TEMPERATURE STABILITY: 100 ppm/ºc for span, 50/ºC for zero OUTPUT FOR EXTERNAL SENSORS: 24Vdc ACCURACY OF THE EXCITATION SUPPLY: +/-20% accuracy. CURRENT CAPACITY OF THE EXCITATION SUPPLY: 30mA for 24V POWER SUPPLY: 95 to 265 Vac standard, 11 to 30Vdc as option.. CURRENT CONSUMPTION: 8VA maximum TEMPERATURE RANGE: Operating: 0 C to + 50 C Storage: - 10 C to + 70 C HUMIDITY: 90% RH maximum at 40ºC, non-condensing ELECTROMAGNETIC-COMPATIBILTY: Emissions EN Immunity EN Certification CE marked ELECTRICAL CONNECTION: 4 way detachable screw terminal connector for conductor size 0.5 to 1.5mm BEZEL SIZE: 96mm wide x 48mm high (1/8 DIN) CUTOUT SIZE: 92mm wide x 45 mm high DEPTH BEHIND PANEL: 125 mm minimum required WEIGHT: 300 grams typically CASE MATERIAL: UL 94V0 rated black ABS Programmable alarm on PM8006 only: ALARM RELAYS: 2 SPCO relays with adjustable hysteresis. Set HIGH or LOW. De-energise on alarm for fail safe RELAY CURRENT RATING: 5A, resistive load. If driving inductive loads, MOV varistors are recommended RELAY VOLTAGE RATING: 250Vac, 24Vdc ALARM HYSTERESIS: Settable from 0 to 9998 counts ALARM SET-POINT STABILITY: +/- 100 ppm/ºc typical ALARM SPEED OF RESPONSE: 15mS typical DIMENSIONS (in mm) ORDER DETAILS State model number only. No options available. MODEL NO. PM8005 PM8006 No alarms 2 programmable alarms CALIBRATION All products manufactured by Ellison Sensors are calibrated using precision calibration equipment with traceability to international standards. Ellison Sensors operates a policy of continuous product development. We reserve the right to change specification without prior notice.