ch4.ai 2008/4/21 U È 05:19:25 ch4.ai 2008/4/21 U È 05:19:25 Media Converters 4

Transcription

1 ch.ai 2008//21 U È 05:19:25

2 NS-200F series_1.ai 2008/5/21 U È 08:01:08 NS-200F series NS-200F Series Industrial 10/100 Base-T(X) to 100 Base-FX Fiber Optics Converter Highlight Information 10/100 LAN x 1 Fiber Optic 100Base-FX x C + 0 Mount NS-200FC/FCS NS-200FT The NS-200F series is a Ethernet(10/100Base-TX) to Fiber Optic(100Base-FX) converter. The Ethernet supports 10/100M auto-negotiation feature and auto MDI/MDIX function. The NS-200F series operates at either half or full duplex mode. It contains "soft start" function with overload protection, high-low voltage protection. The width of the NS-200F series is just mm, so it can be used where space is important. Features Automatic MDI / MDI-X crossover for plug-and-play Each port supports both 10/100 Mbps speed auto negotiation Store-and-forward architecture Full duplex IEEE 802.3x and half duplex backpressure flow control 1.Gbps high performance memory bandwidth Frame buffer memory: 512 Kbit Integrated look-up engine with dedicated 1 K unicast MAC addresses Supports +10~+30Vdc voltage Reverse Polarity Protection Supports operating temperatures from 0 ~ +70 C mount for industrial usage -1 ICP DAS Professional Provider of High Quality Industrial Data Acquisition and Control Products

3 NS-200F series_2.ai 2008/7/ W È 10:3:9 High Reliability Industrial Ethernet Switch for Rugged Environment Specifications Technology Standards Processing Type MAC Addresses Memory Bandwidth Flow Control Interface RJ-5 Port Fiber Port LED Indicators Ethernet Isolation Frame Ground for EMS Protection Multi Mode Single Mode Ethernet Transmission distance Power Input Voltage Range Power Consumption LED Indicator Protection Frame Ground for EMS Protection Mechanical Case Dimensions (W x H x D) Installation Environmental Operating Temperature Storage Temperature Ambient Relative Humidity IEEE802.3, 802.3u, 802.3x Store & forward wire speed switching - no delays Gbps IEEE802.3x flow control, back pressure flow control 10/100BaseT(X) auto negotiation speed, F/H duplex mode, and auto MDI/MDIX connection 100 Base-FX 10/100M, Link/Act, Full duplex/half duplex(fiber Port) 1500 Vrms 1 minute Multi mode fiber cables: 50/125, 62.5/125 or 100/10 μm Distance: 2 km, (62.5/125 μm recommended) for full duplex Wavelength: 1300 or 1310nm Min. TX Output: -20 dbm Max. TX Output: -1 dbm RX Sensitivity: -3 to -31 dbm Single-mode fiber cables: 8.3/125, 8.7/125, 9/125 or 10/125 μm Distance: 15 km, (9/125 μm recommended) for full duplex Wavelength: 1300 or 1310nm Min. TX Output: - 15 dbm Max. TX Output: -8 dbm RX Sensitivity: -36 to -31 dbm Ethernet: 2-pair UTP/STP Cat.3,,5, EIA/TIA ohm Fast Ethernet: 2-pair UTP/STP Cat. 5, EIA/TIA ohm +10 ~ +30VDC (Non-isolation) 1.2A@2VDC, +/- 5% arrowed with 100M Full duplex Power reverse polarity protection Plastic (Flammability UL 9V-0) 33mm x 107mm x 85mm 0 C ~ +70 C -20 C ~ +85 C 10% to 90% non-condensing NS-200F Series -2

4 NS-200F series_3.ai 2008/5/21 U È 08:01:37 LED Functions Standard RJ-5 female connectors are provided. A standard RJ-5 plug cable is necessary to connect your device to the unit since switch that supports auto crossover. 100 Mbps Mbps NS-200F Series LED Color Description PWR Fiber Optic Ethernet LED Indicator Functions Red Off Yellow_On Yellow_Off Green_On Green_Off Yellow Green Off Power is On Power is Off Full Duplex Mode Half Duplex Mode Link/Act Not Networking Link to 10 Mbps Link to 100 Mbps Not Networking Pin# RJ-5 Pin-Out Signal Name RD+ TD+ TD- RD- Function Transmit Data Transmit Data Receive Data Receive Data Pin Function for Terminal Block External power supply is connected using the removable terminal block: +Vs : Power input +10 to +30V GND: Ground F.G. : F.G. stands for Frame Ground (protective ground). It is optional. If you use this pin, it can reduce EMI radiation; improve EMI performance and ESD protection. Appearance LED indicators Plastic case Fiber port LED indicators Power input -3 ICP DAS Professional Provider of High Quality Industrial Data Acquisition and Control Products

5 NS-200F series_.ai 2008/5/23 U È 07:17:28 High Reliability Industrial Ethernet Switch for Rugged Environment Dimensions (Unit: mm) Ordering Information Left Side View Front View Right Side View Back View Bottom View Top View 85.0 NS-200F Series NS-200F - - Fiber Port Connector Single Mode Distance Operating Temperature Ordering Code Definition T: Multi mode ST connector C: Multi mode SC connector CS: Single mode SC connector 0: 0 km Standard Models: 15 km T: Operating Temp: -30 to +75 C Standard Models: 0 to 70 C Models NS-200FT NS-200FC NS-200FCS NS-200FCS-0 NS-200FT-T NS-200FC-T NS-200FCS-T NS-200FCS-0T Accessories GPSU06-6 KWM F DIN-KA52F 2V/0.25A Power Supply, (No-mounting) 2V/0.75A Power Supply, (No-mounting) 2V/1A Power Supply, (With mounting) -

6 NS-200WDM_1.ai 2008/5/21 U È 08:03:01 NS-200WDM NS-200WDM Industrial Single-Strand 10/100 Base-T(X) to 100 Base-FX Media Converter Highlight Information 10/100 LAN x 1 Fiber Optics x C + 0 Mount NEW NS-200WDM-A NS-200WDM-B Using the fiber optic medium for Ethernet applications has become more popular due to fiber optic's excellent physical features, especially for long distance networks. However, fiber optic cable is very expensive, so if we can apply a solution that uses only 1 cable instead of 2, the infrastructure cost can be cut in half. The NS-200WDM Series provides a solution that reduces your expense by 50%! The NS-200WDM Series of Single-Strand Fiber Converters supports Wavelength Division Multiplexing (WDM) technology that allows two independent data communication channels to transmit and receive over one standard, single mode, fiber optic line. This not only doubles your existing bandwidth, but also effectively reduces the cost of creating a new fiber optic infrastructure. 50% Cost Saving for Fiber Optic Infrastructures With a pair of NS-200WDM series products (NS-200WDM-A and NS-200WDM-B), you can double the utilization of your existing, costly fiber optic cable, and save 50% of the cost of a newly installed fiber optic application. It contains "soft start" function with overload protection, high-low voltage protection. The width of the NS-200WDM is just 32mm, so it can be used where space is important. Features Automatic MDI / MDI-X crossover for plug-and-play Each port supports both 10/100 Mbps speed auto negotiation Store-and-forward architecture Full duplex IEEE 802.3x and half duplex backpressure flow control 1.Gbps high performance memory bandwidth Integrated look-up engine with dedicated 1 K unicast MAC addresses Supports +10~+30Vdc voltage Reverse Polarity Protection Supports operating temperatures from 0 ~ +70 C -5 ICP DAS Professional Provider of High Quality Industrial Data Acquisition and Control Products

7 NS-200WDM_2.ai 2008/7/ W È 10:37:22 High Reliability Industrial Ethernet Switch for Rugged Environment Specifications Technology Standards Processing Type MAC Addresses Memory Bandwidth Flow Control Interface RJ-5 Port Fiber Port LED Indicators Ethernet Isolation Frame Ground for EMS Protection Fiber Optic Ethernet Transmission distance Power Input Voltage Range Power Consumption LED Indicator Protection Frame Ground for EMS Protection Connection Mechanical Case Flammability Dimensions (W x H x D) Installation Environmental Operating Temperature Storage Temperature Ambient Relative Humidity IEEE802.3, 802.3u, 802.3x Store & forward wire speed switching - no delays Gbps IEEE802.3x flow control, back pressure flow control 10/100BaseT(X) auto negotiation speed, F/H duplex mode, and auto MDI/MDIX connection 100 Base-FX(Single-mode; SC connector) 10/100M, Link/Act, Full duplex/half duplex(fiber Port) 1500 Vrms 1 minute Single-mode fiber cables: 8.3/125, 8.7/125, 9/125 or 10/125 μm Distance: 15 km, (9/125 μm recommended) for full duplex Wavelength: TX: 1310, RX: 1550 nm for NS-200WDM-A TX: 1550, RX: 1310 nm for NS-200WDM-B Min. TX Output: -1 dbm Max. TX Output: -8 dbm RX Sensitivity: -31 dbm Ethernet: 2-pair UTP/STP Cat.3,,5, EIA/TIA ohm Fast Ethernet: 2-pair UTP/STP Cat. 5, EIA/TIA ohm +10 ~ +30VDC (Non-isolation) 0.12A@2VDC, +/- 5% arrowed with 100M Full duplex Power reverse polarity protection 3-Pin Removable Terminal Block Plastic UL 9V-0 33mm x 107mm x 85mm 0 C ~ +70 C -20 C ~ +85 C 10% to 90% non-condensing NS-200WDM -6

8 NS-200WDM_3.ai 2008/5/21 U È 08:03:5 LED Functions Standard RJ-5 female connectors are provided. A standard RJ-5 plug cable is necessary to connect your device to the unit since switch that supports auto crossover. 100 Mbps Mbps NS-200WDM LED Color Description PWR Fiber Optic Ethernet LED Indicator Functions Red Off Yellow_On Yellow_Off Green_On Green_Off Yellow Green Off Power is On Power is Off Full Duplex Mode Half Duplex Mode Link/Act Not Networking Link to 10 Mbps Link to 100 Mbps Not Networking Pin# RJ-5 Pin-Out Signal Name RD+ TD+ TD- RD- Function Transmit Data Transmit Data Receive Data Receive Data Pin Function for Terminal Block External power supply is connected using the removable terminal block: +Vs : Power input +10 to +30V GND: Ground F.G. : F.G. stands for Frame Ground (protective ground). It is optional. If you use this pin, it can reduce EMI radiation; improve EMI performance and ESD protection. Applications General Media Converter Solution A general media converter requires a pair of fiber optic cables for data transmission and receiving. 10/100Base T(X) 1310 um TX 100Base-FX 1310 um RX 100Base-FX 10/100Base T(X) NS-200FCS NS-200FCS WP-81 Single-Strand Fiber Converter Solution Wavelength Division Multiplexing (WDM) supports bi-directional data transmission and receiving using dual wavelengths (1310/1550 nm) over a single strand, of single-mode optical fiber um 10/100Base T(X) 1310 um 100Base-FX TX & RX 10/100Base T(X) NS-200WDM-A NS-200WDM-B WP-81-7 ICP DAS Professional Provider of High Quality Industrial Data Acquisition and Control Products

9 NS-200WDM_.ai 2008/5/23 U È 07:55:02 High Reliability Industrial Ethernet Switch for Rugged Environment Appearance LED indicators Plastic case Dimensions (Unit: mm) Fiber port 78.0 LED indicators Power input NS-200WDM Left Side View Front View Right Side View Back View Bottom View Top View Ordering Information NS-200WDM-A CR NS-200WDM-B CR 10/100BaseT(X) to 100BaseFX Single-Strand Media Converter, TX 1310 nm, RX 1550 nm, SC (RoHS) 10/100BaseT(X) to 100BaseFX Single-Strand Media Converter, TX 1550 nm, RX 1310 nm, SC (RoHS) Important Note: You must purchase both NS-200WDM-A and NS-200WDM-B since these products work as a pair. Accessories GPSU06-6 KWM F DIN-KA52F 2V/0.25A Power Supply, (No-mounting) 2V/0.75A Power Supply, (No-mounting) 2V/1A Power Supply, (With mounting) -8

10 NS-200G series_1.ai 2008/5/23 U È 01:09:00 NS-200G Series Available Soon Industrial 1000 Base-T to 1000 Base-SX/LX NS-200G series Highlight Information NS-200GSX NS-200GLX NS-200G Series 1000 GbE x LAN Gigabit C + 0 Only for NS-200GSX Series Fiber Optic 1000Base-SX 850um x 1 Only for NS-200GLX Series Fiber Optic 1000Base-LX 1300um Mount x 1 The NS-200G Series is designed to convert Gigabit Ethernet networks to Gigabit fiber networks by transparently converting Ethernet signals to optic signals. That is an ideal solution for bandwidth-hungry applications (such as high resolution digital image transmission, video/audio file streaming/downloading, and server farm connectivity). The flow control mechanism is also negotiated. There is link/data rate LEDs for each port to aid troubleshooting. Port connectors are shielded RJ-5. The width of the NS-200G series is just 33 mm, so it can be used where space is important. Features Automatic MDI / MDI-X crossover for plug-and-play Store-and-forward architecture Full duplex IEEE 802.3x 3.2Gbps high performance memory bandwidth Frame buffer memory: 512 Kbit Integrated look-up engine with dedicated 1 K unicast MAC addresses Supports +10~+30Vdc voltage Reverse Polarity Protection Supports operating temperatures from 0 ~ +70 C mount -9 ICP DAS Professional Provider of High Quality Industrial Data Acquisition and Control Products

11 NS-200G series_2.ai 2008/5/23 U È 01:17:09 High Reliability Industrial Ethernet Switch for Rugged Environment Specifications Technology Standards Processing Type MAC Addresses Memory Bandwidth Interface RJ-5 Port Fiber Port LED Indicators Ethernet Isolation Frame Ground for EMS Protection Multi Mode For SX Single Mode For LX Ethernet Transmission distance Power Input Voltage Range Power Consumption LED Indicator Protection Frame Ground for EMS Protection Mechanical Case Dimensions (W x H x D) Installation Environmental Operating Temperature Storage Temperature Ambient Relative Humidity IEEE802.3, 802.3u, 802.3x, 802.3ab, 802.3z Store & forward wire speed switching - no delays Gbps 1000BaseT auto MDI/MDIX connection 1000 Base-SX(LX) 1000M, Link/Act 1500 Vrms 1 minute Multi mode fiber cables: 50/125, 62.5/125 μm Distance: 500 km, (50/125 μm) for full duplex Wavelength: 850 Min. TX Output: -9.5 dbm Max. TX Output: - dbm RX Sensitivity: Max dbm for 50um Single-mode fiber cables: 9/125 μm Distance: 10 km, for full duplex Wavelength: 1300 nm Min. TX Output: dbm Max. TX Output: -3 dbm RX Sensitivity: Max. -1. dbm Gigabit Ethernet: -pair UTP/STP Cat.5, EIA/TIA ohm +10 ~ +30VDC (Non-isolation) 1.2A@2VDC, +/- 5% arrowed Power reverse polarity protection Plastic (Flammability UL 9V-0) 33mm x 107mm x 85mm 0 C ~ +70 C -20 C ~ +85 C 10% to 90% non-condensing NS-200G Series -10

12 NS-200G series_3.ai 2008/5/26 W È 09::55 Appearance LED indicators Plastic case NS-200G series Dimensions (Unit: mm) Fiber port 78.0 LED indicators Power input Left Side View Front View Right Side View Back View Bottom View Top View Ordering Information NS-200GSX CR NS-200GLX CR 1000 BaseT to 1000 Base-SX Media Converter 1000 BaseT to 1000 Base-LX Media Converter Accessories GPSU06-6 KWM F DIN-KA52F 2V/0.25A Power Supply, (No-mounting) 2V/0.75A Power Supply, (No-mounting) 2V/1A Power Supply, (With mounting) -11 ICP DAS Professional Provider of High Quality Industrial Data Acquisition and Control Products