NB21-7MHR-6. Fusion IR Full HD Bullet IP Camera

Transcription

1 NB21-7MHR-6 Fusion IR Full HD Bullet IP Camera

2 CAUTION! TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. THE GRAPHIC SYMBOLS WITH SUPPLEMENTAL MARKING ARE ON THE BOTTOM OF THE SYSTEM. "WARNING-TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THE UNIT TO RAIN OR MOISTURE" Directions Be careful not to cause any physical damage by dropping or throwing IP Camera. Especially keep the device away from children. Do not disassemble IP Camera. No After Service is assumed when disassembled. Use only the power adapter provided with IP Camera. Be careful to prevent moisture or water penetration into the unit. Particular attention is needed when installing IP Camera. The screw holes for the installation screws and pipes should be maintained tight during the whole life time of the product. All the electrical connection wires plugging in the unit should be prepared so that water from the outside cannot flow into the unit through the surface of the wires. Penetration of the moisture through the wire for extended period can cause malfunction of the unit or deteriorated image. 2

3 Regulatory Notice This equipment has been tested and found to comply with limits for a Class of digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at their own CAUTION! expense. Changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment. 3

4 Contents 1. Introduction Overview Features & Specification Features Specification Applications of IP Camera Product Description Contents Camera mount configuration Product Preview Physical description External View Dimension External Connector Factory Default Switch Functional Description On Site Installation Getting Started PC Requirement Quick Installation Guide Connect PC and IP Camera to network Install IP installer and set IP parameters on IP Camera Remote video connection to IP Camera Additional settings through connection to the Admin Page Troubleshooting No power Cannot connect to the Video Windows Technical Assistance Appendix A Important Notice in Exchanging SD Card (Micro SD)

5 1. Introduction 1.1. Overview The product is multi-codec (H.264, MJPEG) IP camera (or network camera) built with embedded software and hardware technology. It enables real time transmission of synchronized video up to 1,080P and audio data. Remote clients can connect to IP Camera for the real time video/audio data through various client solutions running on PC or smart device. Real time 2-way communication is available through bidirectional audio communication feature. Dark Hunter technology is the most optimized solution for indoor and outdoor surveillance in low-light conditions by using superior CMOS sensor with low-light sensitivity ISP sensor. Furthermore, it can get much vivid image using Super IR LED in extremely low light conditions compared with using conventional IR LED. Designed to be a stand-alone streaming audio & video transmission device, the product can be applied to various application area such as video security, remote video monitoring, distance education, video conference or internet broadcasting system. Vandal proof and weather proof housing will extend the application area to harsh environment of wide temperature range. Embedded PoE (Power of Ethernet, IEEE 802.3af) will enable the owner to reduce TCO (Total Cost of Ownership) by reducing on-site wiring works for the installation. 5

6 1.2. Features & Specification Features H.264MP IP Camera Fusion IR Full HD Bullet IP Camera 1/3 Progressive scan CMOS Sensor Dual-Codec (H.264MP/MJPEG) Progressive scan megapixel (2M CMOS) Multi profile streaming (5 different streams per Resolution, Frame, Rate, Codec) Digital PTZ, video crop Analog video output (CVBS) Built-in standard PoE Two-way audio communication Dark Hunter + Super IR LED Compact design & Easy installation Vandal proof, Weather proof (IP66) Specification Camera Image sensor Full resolution Sync System Lens Day & Night Sensitivity Back Light Compensation White Balance Exposure WDR Progressive scan 1/3 inch CMOS 2M pixels 1,920 x 1,080 pixels (Full HD) Internal 6mm Fixed AUTO, DAY, NIGHT Color : to 0.04Lux, B/W : 0Lux(IR ON) ON / OFF ATW(2.000K ~ 10,000K) / MANUAL / PUSH DC / ESC ON / OFF 3D-DNR 0 ~ 20 Dark Hunter Privacy Mask Motion Detection Digital Zoom AUTO ON (Max. x32) / OFF ON / OFF (1 Programmable Zone) ON / OFF (3 Programmable Zone) X1 ~ X12 6

7 Mirror DEFOG OSD Super IR LED H / V / Rotate ON / OFF BUILT IN 2EA Video Compression method Resolution Multi-Profile Streaming Intelligent Bit-Rate Control PTZ Image Setting Motion detection Simultaneous Dual Codec (H.264MP / MJPEG) 1,920 x 1,080@30fps - 5 simultaneous video profiles - Select the codec type, resolution and frame rates for each profile. Hybrid Bit Rate control (VBR+CBR) Digital PTZ & Video crop Text overlay, Privacy mask, De-interlace filter 3 regions Audio Mono Upstream Mono Downstream 32Kbps G.726 ADPCM, 64Kbps 16bit μ-law PCM ~ MIC/Line-in 64Kbps 16bit μ-law PCM ~ Line-out Network Network Protocol Dynamic IP Security Streaming method - IPv4, TCP/IP, UDP, IGMP, ICMP, ARP, RARP, PPPoE, RTCP - RTP, RTSP, SDP, HTTP, SMTP, FTP, DHCP, UPnP - NTP, DNS, DynDNS Supported - User ID & Password protection, IP address filtering - Digest Authentication, User Access Log - RTSP streaming with proprietary format for control information - standard RTSP streaming - HTTP streaming - Onvif Profile-S External Terminals LAN Analog output Alarm input / output Factory Reset Other 10/100BaseT LAN (auto MDIX) 1 channel D1 CVBS output of the encoding video Alarm I/O (1 Sensor input & 1 Relay output) Supported MIC, Line in / Line out / DC 12V in Installation Standard PoE System Integration Intelligent Video IEEE802.3af Supported Motion Detection 7

8 Alarm Triggers Motion Detection + Sensor Input + Audio Detection Alarm Events Video file upload(ftp), Still Image transmission( ), Relay output Alarm Buffer (Audio/Video) Configurable Pre-alarm (5~15 sec) & Post-alarm (10~60 sec) Operating Environment, Power, Dimensions Operating Temperature -10 C ~ 50 C Operation Humidity 8 ~ 80% RH Power DC 12V, 0.6A Dimensions(W x H x D) Ø 99mm x 252.7mm Weight 1.1kg Casing AL, PC, IP66 Approvals FCC, CE, KC Package information IP camera, CD (User s guide, Software ) Client Software NVR2 64ch (free of charge) Mobile Android, ios (free of charge) Optional Items Local storage Micro SD card Adapter DC 12V, 1.5A 8

9 1.3. Applications of IP Camera Security surveillance (buildings, stores, manufacturing facilities, parking lots, banks, government facilities, military, etc.) Remote monitoring (hospitals, kindergartens, traffic, public areas, etc.) Teleconference (Bi-directional audio conference). Remote Learning, Internet broadcasting Weather and environmental observation 9

10 2. Product Description 2.1. Contents The product package contains followings: Contents Description Remarks IP Camera NB21-7MHR-6 main unit Screws Accessories L-type wrench, CVBS Cable Guide pattern CD Software & User s Guide Power Adaptor Default built in standard PoE module (IEEE802.3af) 12V DC Adaptor (Optional item) 2.2. Camera mount configuration 10

11 2.3. Product Preview IP Camera IP-Installer CMS Software (NVR) NB21-7MHR-6 PC software to allocate an IP address to the IP Camera PC software to view and record the A/V streaming data transmitted from IP camera. (Simultaneous support of up to 64 IP cameras) 2.4. Physical description External View Figure 2-1. External view of IP Camera 11

12 Dimension Unit: mm Figure 2-2. Dimension External Connector Sensor Input (white(+), Red(-)) Relay Output (Black(+), Yellow(-)) Network (LAN) Line Output Power Mic/Line Input Figure 2-3. Connector for external connection Factory Default Switch Factory default switch is provided for returning the IP camera to factory default state. The factory default switch can be found by opening the lower body cap of the camera. There are two functions assigned to factory default switch. 1. Returning to Factory Default State : Press the switch about 5 seconds while power is applied to return to factory default state. 12

13 2. Safe Removal of Micro-SD Card : Press the switch for 1 second to unmount Micro-SD Card for safe removal. Factory Default Switch/ Micro SD Card Eject Video Output (CVBS) Micro SD Card Slot Figure 2-4. Factory Default switch and Micro-SD Card slot 2.5. Functional Description Power : Power input for supplying 12V DC power. Caution : If IP Camera is powered by PoE, do not plug in DC Jack with active DC power into DC power connector. Network (LAN) 100Mbps Ethernet connector (RJ-45) with PoE standard (802.3af). MIC/Line Input Connect external audio source or microphone. Micro SD Card slot Please insert SD memory card when you want to use SD memory card. In case of pulling out SD memory card, please push the SD card. Line Output Connect speakers with built in amplifier. Audio from remote site is output through line out in bi-directional audio mode. 13

14 Relay Output Relay output is provided for connecting alarm devices or for remote on/off control of devices such as light. Relay is normal open and it will be closed upon alarm annunciation or remote on. The relay is capable of switching 30V AC/DC, 2A. For the application which needs power switching beyond this limit, use additional relay switch as shown in the right of Figure 2-5. Alarm Out Device Optional Relay Switch Alarm Out Device Relay Power Supply ( ~30V) ( ~ 2A) (DC/AC) Relay Power Supply ( ~30V) ( ~ 2A) (DC/AC) Power Supply (30V~ ) ( 2A~ ) (DC/AC) * Left : switching requirement below 30V, 2A * Right : switching requirement higher than 30V, 2A. Apply this connection when either voltage or current exceed the limit. Figure 2-5. RELAY Output connection Sensor Input Connect external alarm sensor. Examples of sensing devices are infrared sensor, motion sensor, heat/smoke sensor, magnetic sensor, etc. Connect the two wires of the sensors to SNS In. The sensor type(nc/no) can be set in admin page. Multiple sensor devices can be connected in parallel. Photo Coupler NO/NC Type Open Collector Type Sensor1+ Sensor Device Sensor Device +12V GND Sensor1- Sensor Power Supply Sensor Power Supply Figure 2-6. SENSOR input and connection of the sensor 14

15 3. On Site Installation Use cables and conduits that are suitable for the installation and that are compliant to IP66. Particular attention should be paid in the installation so that no moisture is allowed to penetrate into the unit through the cables or conduits during the life time of the product. Products of which the internal parts are exposed to moisture because of improper installation are not covered by warranty. Follow the procedure below for proper installation 1. Fix the base on the wall. 2. Adjust the rotational position of the camera for desired viewing of the site. 15

16 Precautions Outdoor Installation : Leaking expected at connected cable on outdoor installation. Use the waterproof rubber tape winding up on cable connection as following picture. 1) Connect cables. 2) Winding rubber tape with half overlay on external cable jacket (A) and cable connection. The tape material butyl rubber is extended more than double size. Winding tightly cable connection to prevent leaking on cable. This product is IP66 waterproof certified one but the external cable connection part is not waterproof. Do not expose cable on dropping water or humid place and be sure to wring waterproof rubber tape. 16

17 4. Getting Started 4.1. PC Requirement Audio/Video streaming data received from IP Camera can be displayed or stored in a PC running client programs. Minimum requirement of the PC is described below: Minimum Requirement Recommended Specification CPU Intel Core i3 3Ghz Intel Core i7 Main Memory 2GB 4GB Operating System * Windows XP Windows 7 (64bit) Web Browser Internet Explorer 8, 9 Internet Explorer 8, 9 Graphic Card Video RAM 256MB Resolution 1920x1080 Video RAM 1GB Higher than 1920x1080 Network 10 Base-T Ethernet 100 Base-T Ethernet * Operating Systems supported: Windows 2000 Professional, Windows XP / Vista / Quick Installation Guide Connect PC and IP Camera to network. 1. Prepare a PC to run programs for the installation and video connection (PC is needed to assign IP address to IP Camera) 2. Connect IP Camera as shown in dotted line in Figure 4-1. The DC power through DC adaptor is no need to connect if LAN switch supports PoE (IEEE802.3af). DC adaptor LAN switch LAN switch with standard POE (802.3af) Figure 4-1. Power and network connection 17

18 Install IP installer and set IP parameters on IP Camera 1. Please insert the Setup CD into your CD-ROM drive, and then please setup 2. Please click Install button to begin the Installation. Figure IP Installer Setup 1 Figure IP Installer Setup 2 3. Please click Finish button to complete the installation. Figure IP Installer Setup 3 18

19 4. XNET IP Installer program is automatically launched like below right after the program installation. Figure IP Installer Start box 5. Select the camera of which you wish to change the IP address and click (Set IP Address) button to bring up the following box in Figure Figure IP Address box 19

20 6. When you enter the IP address and click Set button, the box shown in Figure will appear. Figure Select Network Adapter Box 7. Select the adapter and click Select button to change the IP address of the camera. 20

21 Remote video connection to IP Camera 1. Connection through Web Viewer Web Viewer offers the simplest way of video connection to IP Camera. For video connection, enter the IP address of IP Camera in the URL window of Internet Explorer as: [e.g.] Port 80 Can be omitted the default port of 80 [e.g.] Port 8080 Note : Active-X module should be installed on your PC before actual connection. If your PC is not connected to the internet, you cannot download Active-X module. Most convenient way of installing the Active-X module is installing NVR2 which is available from the CD or our web site. Connection to Admin Page Basic Control Figure 4-3. Web Viewer Default ID and password of Admin Page are root, admin. 21

22 2. Connection through NVR2 NVR2 is a multi-channel CMS program for IP camera or Video server. Install NVR2 on remote PC to connect to these products. It is needed to assign connection information to NVR2 program before connection. Details for the NVR2 can be found in [NVR2 User s Guide]. Figure 4-4. NVR Additional settings through connection to the Admin Page All the parameters of new IP camera follows factory default values. For more sophisticated target application, it is needed to change parameters. The admin page can be connected through. It is needed to enter ID and password of the administrator. Default ID and password are root, admin. 22

23 5. Troubleshooting 5.1. No power In case of Standard PoE (Power over Ethernet) Power supply through standard PoE is possible only when the following conditions are met. 1. Standard PoE is supported on the product. 2. The LAN switch supports standard PoE. Make sure that both IP camera and LAN switch support standard PoE (IEEE 802.3af) In case of DC adaptor If PoE is not applied, the power and network connection should be made through separated cables. It is recommended to use DC adaptor supplied by provider for the feeding of the power. In case of replacing the DC power supply, make sure that the power supply meets with the power requirement of the IP camera to prevent damage or malfunction Cannot connect to the Video Check the status of the network connection through PING test. Try the following on your PC : - Start > Run > Cmd > Ping IP address (Ex : Ping ) - If Reply from ~ message is returned (1 in the figure below), the network connection is in normal state. Try connection to the video again. If the problem persists, or refer to other trouble shooting notes. - If Request timed out message is returned. (2 in the figure below), the network connection or network setting is not in normal state. Check the network cable and settings

24 5.3. Windows 7 Windows 7 users need to configure UAC (User Access Control) and Privilege Level for proper recording and still video capture in NVR and Web Viewer. 1. UAC (User Access Control) configuration 1) Double-click User Accounts in control panel 2) Double-click Change User Account Control setting 3) Set to Never notify 2. Privilege Level Control 1) Select NVR icon on the desktop 2) Click right mouse button and select properties 3) Check Privilege Level in Compatibility tab 24

25 5.4. Technical Assistance If you need any technical assistance, please contact your dealer. For immediate service. please provide the following information. 1. Model name 2. MAC address and Registration number 3. Purchase date 4. Description of the problem 5. Error message 25

26 Appendix A Important Notice in Exchanging SD Card (Micro SD) SD Card is a non-volatile memory device for storing video and audio data on the product. Continued writing to the SD Card will cause wear-off of the memory cell. When you plug out the SD Card for replacement or other purpose, follow the steps below in order to prevent data loss or crash of the SD Card. 1. Press factory default button for 1 sec to unmount the SD Card. SD Card can also be unmounted by going to Admin Page -> Sensor&Capture Setup and clicking on CONFIRM button at the right of SD Card Unmount menu. 2. Unplug the SD Card. If no action is taken within 1 minute, SD Card will be mounted again. 3. Plug in new SD Card 4. If the SD Card is a new one for the IP camera, format the SD Card by following the steps below. Go to Admin Page -> Sensor & Capture Setup In the SD Card management menu, click on CONFIRM button at the right of SD Card Format. 26