Operating Instructions (Compact) SIMATIC. Industrial PC SIMATIC Microbox PC 420. Siemens. Release 11/2006 A5E

Transcription

1 Operating Instructions (Compact) 1 SIMATIC Industrial PC Release 11/2006 A5E Siemens

2 Safety Guidelines This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are graded according to the degree of danger. Danger indicates that death or severe personal injury will result if proper precautions are not taken. Warning indicates that death or severe personal injury may result if proper precautions are not taken. Caution with a safety alert symbol, indicates that minor personal injury can result if proper precautions are not taken. Caution without a safety alert symbol, indicates that property damage can result if proper precautions are not taken. Notice indicates that an unintended result or situation can occur if the corresponding information is not taken into account. If more than one degree of danger is present, the warning notice representing the highest degree of danger will be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to property damage. Qualified Personnel The device/system may only be set up and used in conjunction with this documentation. Commissioning and operation of a device/system may only be performed by qualified personnel. Within the context of the safety notes in this documentation qualified persons are defined as persons who are authorized to commission, ground and label devices, systems and circuits in accordance with established safety practices and standards. Prescribed Usage Note the following: Warning This device may only be used for the applications described in the catalog or the technical description and only in connection with devices or components from other manufacturers which have been approved or recommended by Siemens. Correct, reliable operation of the product requires proper transport, storage, positioning and assembly as well as careful operation and maintenance. Trademarks All names identified by are registered trademarks of the Siemens AG. The remaining trademarks in this publication may be trademarks whose use by third parties for their own purposes could violate the rights of the owner. Disclaimer of Liability We have reviewed the contents of this publication to ensure consistency with the hardware and software described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the information in this publication is reviewed regularly and any necessary corrections are included in subsequent editions. 이기기는업무용 (A 급 ) 전자파적합기기로서판매자또는사용자는이점을주의하시기바라며가정외의지역에서사용하는것을목적으로합니다. Siemens AG Automation and Drives Postfach NÜRNBERG GERMANY Order No.: A5E Release 11/2006 Copyright Siemens AG 2004, Technical data subject to change

3 1 1.1 Components of the Product Amount Name 1 1 Accessory kit: 2 mounting brackets, 9 oval-head screws (M4x6), 1 USB strain relief Additionally supplied with Windows XP Professional: Amount Name Description 1 Recovery CD Contains the tools for setting up the hard disk and the Windows XP Professional operating system. 1 Restore DVD Contains a hard disk image file with the original software (operating system with installed hardware drivers). 1 Documentation and Drivers CD Contains the documentation and the hardware drivers. 1 SP2 CD Contains the update with Windows XP Professional SP2 1.2 Device identification data Enter the identification data of the device into the table: Serial number (on the type plate) Oder number of the device For the Windows XP Embedded / XP Professional variant: Microsoft Windows Product Key from the "Certificate of Authenticity" (COA). The COA label is pasted to the device. Ethernet Adressen: BIOS Setup (F2 Key) under Main > Hardware Options > Ethernet Address Siemens, Release 11/2006, A5E

4 1.3 Configuration 1.3 Configuration Device Configuration Order No. 6 O G O x x 0-0 x x 0 Celeron 400 MHz, 100 MHz FSB Celeron 400 MHz, 100 MHz FSB, PROFIBUS DP12 Celeron 400 MHz, 100 MHz FSB, CAN interface Celeron 650 MHz, 100 MHz FSB Celeron 650 MHz, 100 MHz FSB, PROFIBUS DP12 Pentium III, 933 MHz, 133 MHz FSB Pentium III, 933 MHz, 133 MHz FSB, PROFIBUS DP MB SDRAM MB SDRAM MB SDRAM GB EIDE hard disk O 256 MB Compact Flash card M 512 MB Compact Flash card N 1 GB Compact Flash card P 2 GB Compact Flash card Q Without mass storage X Windows XP Embedded preinstalled 1 O Windows XP Professional MUI preinstalled 2 B Without operating system X 1 Together with 512 MB, 1 GB, 2 GB Compact Flash card or 40 GB EIDE hard disk 2 Together with 40 GB EIDE hard disk O B C D E G H Accessories Order No. Expansion kit PC/104 6 O G B O X O MB Compact Flash card 6 E S B F X C MB Compact Flash card 6 E S B F X D 0 1 GB Compact Flash card 6 E S B F X E 0 2 GB Compact Flash card 6 E S B F X F 0 SIMATIC USB Flash Drive, USB 2.0, 512 MB 6 E S D C O O 0 4, Release 11/2006, A5E

5 1.4 Safety Instructions 1.4 Safety Instructions Caution In order to avoid substantial damage and for your own safety, note the safety instructions in this documentation and in the operation instructions. 1.5 Permitted mounting positions Notice The device is approved for operation in closed rooms only. Ensure at least 100 mm of space above and below the device and between other components or the sides of cabinets. Horizontal (preferred position) Vertical Permissible ambient temperature: Operating with Compact flash card: 0 to +50 C Operating with the hard disk: +5 to +40 C Permissible ambient temperature: Operating with Compact flash card: 0 to +45 C Operating with the hard disk: +5 to +40 C Siemens, Release 11/2006, A5E

6 1.6 Installation / panel-mounting 1.6 Installation / panel-mounting Mounting on DIN rails 1 Place the device aslant on the upper top hat rail 2 Swing the device fully onto the rails until both clamps (1) completely latch. Wall mounting 1 Loosen the screws (2) and remove the two clamps (1) from the rear of the device. 2 Install two cubicle angles with screws (3) onto the device. Examples for mounting and materials can be found in the operation instructions. 1.7 Connection components Connector locations Pos Name Description (1) 24 VDC Connection for a 24 V DC power supply (2) COM 1 Serial port 1 (RS232), 9-pin Cannon socket (3) DVI/VGA DVI/VGA connection for CRT or LCD monitor with DVI interface (4) USB 2 USB 2.0 connectors high speed / low current (5) USB 2 USB 2.0 connectors high speed / high current (6) Ethernet RJ45 Ethernet connection 1 (exclusive PCI interrupt) for 10/100 Mbps (7) Ethernet RJ45 Ethernet connection 2 (shared PCI interrupt) for 10/100 Mbps (8) PROFIBUS DP/MPI Other field bus (9) USB strain relief fastener (10) Protective earth terminal PROFIBUS DP/MPI interface (RS 485 isolated), 9-pin Cannon socket or other field busses (on request) The USB strain relief must be fastened to the device housing with an oval-head screw (M4 thread). The USB cable is fastened to the strain-relief with a cable binder. The protective earth terminal (M4 thread) which is integrated into the device needs to be connected to the protective earth conductor. The minimum conductor cross-section may not be less than 2.5 mm 2. 6, Release 11/2006, A5E

7 1.8 Connecting the 24 V DC power supply 1.8 Connecting the 24 V DC power supply To be noted before you connect the device Note the following in order to operate the device safely and according to regulation: Warning The device should only be connected to a 24V DC power supply which satisfies the requirements of safe extra low voltage (SELV). When the device is operated on a wall, in an open rack or other similar locations, an NEC Class 2 current source is required for the compliance of the UL requirements (in accordance with UL ). In all other cases (in accordance with IEC / EN / DIN EN ) either a power source of limited performance (LPS = Low Power Source), or a line-side fuse or a line-side power switch is necessary. The power needs to be limited to a value lower than 8 A. Recommended fuse rating: 4 A. Use the special plug supplied to connect the supply voltage. Operation in closed cabinets or fireproofing cabinets (including the operation of a cabinet in accordance with UL508) ther are no requirements for current limiting of the supply voltage. Notice The permitted cable cross-section for the 24 V DC connection is 0.75 mm 2 to 2.5 mm 2. Notice If a Compact Flash card is used in the device, be sure that the card is properly installed before you connect it. Connecting Steps for connecting the device to the 24 V DC power supply 1. Switch off the 24 V DC power source. 2. Connect the power supply using the plug (included in the package). Siemens, Release 11/2006, A5E

8 1.9 Protective ground connection 1.9 Protective ground connection A low-impedance earth connection ensures that interference signals generated by external power supply cables, signal cables or cables to the I/O modules are safely discharged to earth. Required tool for protective earth terminal: TORX T20 screwdriver Protective earth terminal The protective earth terminal (M4 threads) (1) on the device (large surface, large-area contact) has to be connected with the protective earth conductor of the cabinet or plant in which the PC is to be installed. The minimum conductor cross-section may not be less than 2.5 mm Commissioning Information Notice Windows XP Embedded: Observe EWF Information Under Windows XP Embedded a configurable write filter Enhanced Write Filter) is available. As from Windows XP Embedded SP2 the EWF is deactivated by default. Please observe the EWF rules during activation and use, since a data loss may otherwise occur. 8, Release 11/2006, A5E

9 1.11 Service and support 1.11 Service and support Further Support If you have any further questions relating to the products described in this documentation, contact your local representative at the SIEMENS office nearest you. Find your contact partner at: A signpost to the documentation of the various SIMATIC products and systems is available at: The online catalog and the online ordering system is available at: Training center Siemens offers a number of training courses to familiarize you with the SIMATIC automation system. Please contact your regional training center or the central training center in Nuremberg, D Germany. Telephone: +49 (911) Internet: Technical Support You can reach technical support for all A&D products at: Support Request form on the web: Telephone: Fax: Further information about our technical support is available in the Internet at When you contact the Customer Support, please have the following information for the technician on hand: BIOS version Order No. (MLFB) of the device Installed additional software Installed additional hardware Siemens, Release 11/2006, A5E

10 1.11 Service and support Service & Support on the Internet In addition to our documentation, we offer a comprehensive knowledge base online on the Internet at: There you will find: The Newsletter contains the latest information on your products Numerous documents are available by searching through Service & Support The current BIOS version A forum is available for users and specialists to exchange experiences Your local Siemens partner for Automation & Drives in our Partner database Information about local service, repairs, and spare parts. Lots more is available on the Services page You can find the latest information about your device at the following address: Product documentation The detailed operating instructions for Microbox PC420 can be downloaded as a PDF file on the internet under the following address: 10, Release 11/2006, A5E