SGPAT10xx /100/1000Base-T to 1000Base-SX/LX PoE PSE+ GbE Media Converter User Guide Rev. A

Transcription

1 SGPAT10xx /100/1000Base-T to 1000Base-SX/LX PoE PSE+ GbE Media Converter User Guide Rev. A

2 Trademarks All trademarks and registered trademarks are the property of their respective owners. Copyright Notice/Restrictions Copyright 2011, 2012 Transition Networks All rights reserved. No part of this work may be reproduced or used in any form or by any means (graphic, electronic or mechanical) without written permission from Transition Networks. Printed in the U.S.A. SGPAT10xx /100/1000Base-T to 1000Base-SX/LX PoE PSE+ GbE Media Converter User Guide, Rev. A Contact Information Transition Networks Red Circle Drive Minnetonka, MN USA Tel: or Fax: Revision History Rev Date Description A 07/12/12 Initial release. Page 2 of 23

3 Cautions and Warnings Definitions Cautions indicate that there is the possibility of poor equipment performance or potential damage to the equipment. Warnings indicate that there is the possibility of injury to a person. Cautions and Warnings appear here and may appear throughout this manual where appropriate. Failure to read and understand the information identified by this symbol could result in poor equipment performance, damage to the equipment, or injury to persons. Cautions Do not ship or store devices near strong electrostatic, electromagnetic, magnetic, or radioactive fields. Caution: When handling media converters, observe electrostatic discharge precautions. This requires proper grounding (i.e., wear a wrist strap). Caution: Copper based media ports, e.g., Twisted Pair (TP) Ethernet, USB, RS232, RS422, RS485, DS1, DS3, Video Coax, etc., are intended to be connected to intra-building (inside plant) link segments that are not subject to lightening transients or power faults. They are not to be connected to inter-building (outside plant) link segments that are subject to lightening. Caution: Do not install the media converters in areas where strong electromagnetic fields (EMF) exist. Failure to observe this caution could result in poor media converter performance. Caution: Read the installation instructions before connecting the chassis to a power source. Failure to observe this caution could result in poor performance or damage to the equipment. Caution: Only trained and qualified personnel should install or perform maintenance on these devices. Failure to observe this caution could result in poor performance or damage to the equipment. Page 3 of 23

4 Caution: Do not let optical fibers come into physical contact with any bare part of the body since they are fragile, and difficult to detect and remove from the body. Caution: Do not bend any part of an optical fiber/cable to a diameter that is smaller than the minimum permitted according to the manufacturer s specification (usually about 65 mm or 2.5 in)! Warnings Warning: Use of controls, adjustments or the performance of procedures other than those specified herein may result in hazardous radiation exposure. Warning: Visible and invisible laser radiation when open. Do not look into the beam or view the beam directly with optical instruments. Failure to observe this warning could result in an eye injury or blindness. Warning: Do not work on the device, or connect or disconnect cables during a storm with lightning. Failure to observe this warning could result in an electrical shock or death. Page 4 of 23

5 Table of Contents Caution...6 Electronic Emission Notices Introduction...7 Overview...7 Checklist...7 Features...8 Hardware Description...8 Models...9 LED Indicators...10 Network Interfaces...10 User Interfaces on the Right Panel...11 User Interfaces on the Right Panel...11 LPT and RFD function...12 PoE Technology Installation...14 Hardware and Cable Installation...14 Wall Mount Installation (Optional)...14 Desktop Installation (Optional)...14 Cabling Requirements Applications SGPAT10xx-100 connected to IP CAM (PD) SGPAT10xx-100 connect to PoE Splitter...16 LPT (Link Pass Through) Applications Converter to Converter in pairs Converter Connects to Fiber Switch...18 Appendix A - General Specifications...19 Fiber Optic Specifications...19 Service...20 Warranty...20 Page 5 of 23

6 Caution Circuit devices are sensitive to static electricity, which can damage their delicate electronics. Dry weather conditions or walking across a carpeted floor may cause you to acquire a static electrical charge. To protect your device, always touch the metal chassis of your computer to ground the static electrical charge before you pick up the circuit device. Electronic Emission Notices Federal Communications Commission (FCC) Statement This equipment has been tested and found to comply with the limits for a class A computing device pursuant to Subpart J of part 15 of FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. European Community (CE) Electromagnetic Compatibility Directive This equipment has been tested and found to comply with the protection requirements of European Emission Standard EN55022/EN and the Generic European Immunity Standard EN EMC: EN55022(1988)/CISPR-22(1985) class A EN (1995) EN IEC (1995) IEC (1995) IEC (1995) class A 4K V CD, 8KV, AD 3V/m 1KV (power line), 0.5KV (signal line) Page 6 of 23

7 1. Introduction Overview The TN SGPAT10xx-100 is a 10/100/1000Base-T to 1000Based-SX/LX (SC/LC) IEEE802.3z/ab GbE media converter, which allows two types of network segments to be connected easily and inexpensively. It complies with IEEE802.3at (max. PoE output power consumption up to 30W) Power over Ethernet standard. This AC powered PoE media converter is a Power Sourcing Equipment (PSE), providing power to both IEEE802.3af and IEEE802.3at powered device (PD) over the existing Cat. 5e UTP cable. The converter includes PD signal sensing and power monitoring features. We are using PSE+ to represent the high power PoE output max. 30W. Checklist Before you start installing the converter, verify that the shipping package contains: The SGPAT10xx-100 GbE Media Converter AC Power Cord Product Documentation Card, PN Four adhesive-backed rubber feet SGPAT10xx-100 AC Power Cord This User Guide manual is available on the TN website. Please notify your sales representative immediately if any of the items are missing or damaged. 335xx Rev. A Page 7 of 23

8 Features Key Features IEEE802.3at PoE (Power over Ethernet) PSE+ compatible ---Internal AC power supply ---Over-current protection ---Under-current detection ---Minimum load sensing ---Fault protection input ---PSE MDI power enable/disable Supports LPT (Link Pass-through) and RFD (Remote Fault Detect) Supports 802.3x flow control for full-duplex port and backpressure for half-duplex port DIP switch to set configurations DIP 1:Cut-Through Mode/Normal Mode DIP 2:LPT/LPT DIS DIP 3:PoE/PoE DIS Supports jumbo frame (Normal Mode:2KB, Cut-Through Mode:9KB) PSE RJ-45 Pin-out Alternatives A/B Auto detection RoHS Compliance Hardware Description Fig. 1-1: Full View of SGPAT10xx-100 Page 8 of 23

9 Models Model SGPAT SGPAT SGPAT SGPAT Description 10/100/1000Base-T to 1000Base-SX PoE PSE+ GbE converter, SC Multi-Mode 10/100/1000Base-T to 1000Base-LX PoE PSE+ GbE converter, SC Single-Mode 10km 10/100/1000Base-T to 1000Base-SX PoE PSE+ GbE LC converter, Multi-Mode 10/100/1000Base-T to 1000Base-LX PoE PSE+ GbE converter, LC Single-Mode 10km Fig. 1-2: Front View of SGPAT Page 9 of 23

10 LED Indicators There are 6 diagnostic LEDs located on the Front panel of SGPAT10xx-100 GbE Media Converter. These LED indicators provide administrators with real-time system status. The table below describes the LED indicator functions. LED Color Function PWR Green Lit when power is coming up LNK/ACT 2 Green Lit when fiber connection is good Blinks when fiber data is present LNK/ACT 1 10/100/1000 Mbps Green Green/ Amber Lit when TP connection is good Blinks when TP data is present Lit Green when TP link on 1000Mbps Lit Amber when TP link on 100Mbps Off when TP link on 10Mbps PoE1 Green Lit when RJ-45 (1,2),(3,6) pairs detect PD PoE2 Green Lit when RJ-45 (4,5),(7,8) pairs detect PD Network Interfaces Close-up of LEDs and Network Connectors Port TP Port Fiber Port Function 10/100Base-TX Auto-Negotiation Auto-MDIX Flow control for Full-Duplex, backpressure for Half-Duplex 1000Base-TX Auto-Negotiation Auto-MDIX only for Auto-Negotiation Flow control for Full-Duplex only 1000Base-SX/LX (SC/LC) with NWay flow control Link partner must be 1000FDX with NWay flow control Page 10 of 23

11 User Interfaces on the Right Panel The right panel provides access to a configuration DIP switch and a RESET switch. Fig. 1-3: Right View of SGPAT DIP Switch and Reset button Before you make any changes to DIP switch settings, make sure that the power has been turned off. Or press the RESET button after you change DIP switch 1 or 2 setting. Switch DIP 1 DIP 2 Function Cut-Through Mode (default) or Normal Mode. Cut-Through mode supports jumbo frame up to 9216 Bytes. Normal mode supports frame up to 2048 Bytes. LPT Enable (default) or Disable. DIP 3 PoE Enable (default) or Disable. Page 11 of 23

12 LPT and RFD function The LPT (Link Pass-through) allows the media converter to monitor both the fiber and copper RX ports for loss of signal. In case of a loss of RX signal on one media port, the converter will automatically disable the TX signal to the other media port, thus passing through the link fault. RFD (Remote Fault Detect) lets the converter stop sending link pulse to the link partner once a loss of the fiber RX signal is encountered. Then the link partner will synchronously stop sending data. FEF prevents loss of valuable data transmitted over invalid link. Combining LPT and FEF troubleshooting features of SGPAT10xx-100, both end devices can be notified of a loss of fiber link. When link fault pass through function is enabled, link status on TX port will inform the FX port of the same device and vice versa. From the link fault pass through procedure illustrates in the figure below, if link fail happens on TX port (1), the local FX port sends non-idle pattern to notice the remote FX port (2). The remote FX port then forces its TX port to link failed after receiving the non-idle pattern (4). In other words, this mechanism will alert the link fault status of local TX port to the remote converter s TX port, and the link status of the remote TX port will become off. Link status LED will also be off for both SGPAT10xx-100 and its link partner. PoE Technology Power over Ethernet or PoE technology describes a system to transfer electrical power, along with data, to remote devices over standard twisted-pair cable in an Ethernet network. This technology is useful for powering IP telephones, wireless LAN access points, network cameras, remote network switches, embedded computers, and other appliances where it would be inconvenient, expensive (mains wiring must often be done by qualified and/or licensed electricians for legal or insurance reasons) or infeasible to supply power separately. It doesn't require modification of existing Ethernet cabling infrastructure. IEEE 802.3af (Power over Ethernet), the specification allows the powering device to use a voltage between VDC, though the nominal voltage is 48V, over two of the four available pairs on a Cat.3/Cat.5e cable with a selectable current of ma subject to a maximum load power of 15.40W. Only about 12.95W are available after counting cable losses, and most switched power supplies will lose another 10 25% of the available power. Page 12 of 23

13 IEEE 802.3at (Max. PoE output power consumption up to 30W) is an updated standard in progress referred to as PoE plus or 802.3at introduces increases available power. Numerous non-standard schemes had been used prior to PoE standardization to provide Power over Ethernet cabling. Some are still in active use. The standard describes two types of devices: 1. Power Sourcing Equipment(PSE) and Powered Devices(PD), and 2. PSE provides power to the PD. The PoE PSE+ converter may auto-detect PD and provide power via one of two valid four-wire connections. In each four-wire connection, the two conductors associated with a pair each carry the same nominal current in both magnitude and polarity. Refer to following figure in conjunction with PSE pinout alternative table, illustrates the valid alternatives. PSE Pinout Alternative Table PD and PSE Eight-Pin Modular Jack (RJ-45) Page 13 of 23

14 2. Installation Hardware and Cable Installation Caution: Wear a grounding device to avoid damage from electrostatic discharge. Power Installation Power requirement: 100~240 VAC, 50~60Hz. Connect to an AC power source with AC power cord. Wall Mount Installation (Optional) For some applications, you will find it convenient to mount SGPAT10xx-100 on the wall using the wall mount holes on the side of the unit (shown below). Desktop Installation (Optional) For other applications, you will find it convenient to mount SGPAT10xx-100 using the four provided adhesive-backed rubber feet (location shown above). Page 14 of 23

15 Cabling Requirements To help ensure a successful installation and keep the network performance good, please take care on the cabling requirement. Cables with worse specification will render the LAN to work poorly. Cabling Requirements for TP The grade of the cable must be Cat. 5e with a maximum length of 100 meters. Cabling Requirements for FX 1000Base-SX/LX network only support full-duplex mode. The Switch-based Media Converter breaks up TP and Fiber segments collision domain to extend the cabling distance. Mode Multi-Mode Fiber 62.5/125μm Multi-Mode Fiber 50/125μm Bandwidth Bandwidth Distance MHz-Km MHz-Km Distance 1000SX (SC/LC) m m 850nm m m 1000LX (SC/LC) 1310nm Single-Mode Fiber 9/125μm Single-Mode transceiver 1310nm: 10Km Page 15 of 23

16 3. Applications 1. SGPAT10xx-100 connected to IP CAM (PD) The following is a simple example to illustrate how to use SGPAT10xx-100 PoE PSE Media Converter to set up your system, and to test if your SGPAT10xx-100 functions normally. Use a suitable fiber cable to connect these two SGPAT10xx-100s, use Ethernet cables to connect the PC to the SGPAT10xx-100, and connect the IP CAM as shown in Fig. 3-1 You can view the image from PC through IP CAM after connection is successful. Fig. 3-1: IP CAM (PD) Connection 2. SGPAT10xx-100 connect to PoE Splitter In this example, the SGPAT10xx-100 TP connects to a PoE splitter, and FX connects to a GbE converter or switch that depends on the user. Fig. 3-2: IP CAM (PD) Connection (PoE Splitter or Converter/Switch Connection) Page 16 of 23

17 LPT (Link Pass Through) Applications The Converter model of LPT (link pass through) in TX/FX converter application is controlled by the software and instantly take effect. Link status on one port is propagated to the other port to notice the remote nodes. If the TP port is unplugged, this converter stops transmission on fiber port. This causes the remote fiber node link to fail. LED shows the link failure on both TP and fiber ports. If the fiber link fails, this converter restarts auto-negotiation on TP port but always stays in the link failure state. This causes the remote TP node link to fail. The LED also shows the link failure on both the TP and fiber ports. See Fig. 4-1 and 4-4 below for the normal status when the link succeeds. See Fig. 4-2 thru Fig.4-6 for the error status when TP Cable A, Fiber Cable B, or Fiber Cable C fails to connect. Note: The Link through (LPT) function only takes effect with the LPT DIP switch in the Enable position. The SGPAT10xx-100 can support the following two LPT typical applications: 1. Converter to Converter in pairs Fig. 4-1: Normal status via LPT converter Fig. 4-2: The status as TP Cable A or D is broken Fig. 4-3: The status as Fiber Cable B or C is broken Page 17 of 23

18 2. Converter Connects to Fiber Switch SGPAT10xx-100 User Guide Fig. 4-4: Normal status via LPT converter Fig. 4-5: The status as TP Cable A is broken Fig.4-6: The status as Fiber Cable B or C is broken Note : Indicates LNK/ACT LED Lit Indicates LNK/ACT LED Off Note: The LPT (Link Pass Through) function can work with different link partners (e.g., Fiber port on Switch). LPT does not need both converters with the same model in pairs. Page 18 of 23

19 Appendix A - General Specifications Feature Description Power Requirement 100~240VAC, 50~60Hz Power Consumption 35 W Operating Temperature 0 to 40 C Storage Temperature -20 to 70 C Humidity 5% to 90% Dimensions 158(W) x 40(H) x 133(D) mm Weight 0.44kg Installation Wall mount, Desktop MAC Address table 1k Complies with FCC Part 15 Class A and CE Mark Fiber Optic Specifications Model # Media Speed Connector SGPAT MM Fiber 1000 Mbps MM SC 550 m SGPAT MM Fiber 1000 Mbps MM LC 550 m SGPAT SM Fiber 1000 Mbps SM SC 10 km SGPAT SM Fiber 1000 Mbps SM LC 10 km Up to Distance Model # Wavelength (nm) Min TX Output (dbm) Max TX Output (dbm) Sensitivity (dbm) SGPAT SGPAT SGPAT SGPAT Power Budget (db) Remarks: MM = Multi-Mode SM = Single-Mode SC = Duplex SC Connector LC = Duplex LC Connector Page 19 of 23

20 Service Direct Contact Numbers: Domestic: International: Fax techsupport@transition.com Service Hours: USA: 7 AM until 8 PM CST Monday to Friday. China: 8 AM until 4 PM China Central Standard Time Monday to Friday. Out of Hours the calls will be answered by an on-call engineer. Live Help Online Support: Chat live with a Transition Networks representative; go to Warranty This warranty is your only remedy. No other warranties, such as fitness for a particular purpose, are expressed or implied. Transition Networks is not liable for any special, indirect, incidental or consequential damages or losses, including loss of data, arising from any cause or theory. Authorized resellers are not authorized to extend any different warranty on transition networks behalf. Limited Lifetime Warranty Effective for products shipped May 1, 1999 and after. Every Transition Networks labeled product purchased after May 1, 1999 will be free from defects in material and workmanship for its lifetime. This warranty covers the original user only and is not transferable. What the Warranty Does Not Cover This warranty does not cover damage from accident, acts of God, neglect, contamination, misuse or abnormal conditions of operation or handling, including over-voltage failures caused by use outside the product s specified rating, or normal wear and tear of mechanical components. If the user is unsure of the proper means of installing or using the equipment, contact Transition Networks free technical support services. Establishing Original Ownership To establish original ownership and provide date of purchase, please complete and return the registration card accompanying the product or register the product on-line on our product registration page. Transition Networks will at its option: Repair the defective product to functional specifications at no charge Replace the product with an equivalent functional product Refund the purchase price of a defective product Who to Contact for Returns To return a defective product for warranty coverage, contact Transition Networks technical support department for a return authorization number. Transition's technical support department can be reached through any of the following means: Service Hours Mon thru Fri 7 AM - 6 PM CST: Contact Tech Support via telephone at or Fax Page 20 of 23

21 Live web chat: Transition Now Any Other Time: Voice Mail x 579 or x 579 How and Where to Send Returns Send the defective product postage and insurance prepaid to the following address: Transition Networks, Inc Red Circle Drive Minnetonka, MN USA Attn: RETURNS DEPT: CRA/RMA # Failure to properly protect the product during shipping may void this warranty. The return authorization number must be written on the outside of the carton to ensure its acceptance. We cannot accept delivery of any equipment that is sent to us without a CRA or RMA number. CRAs are valid for 60 days from the date of issuance. An invoice will be generated for payment on any unit(s) not returned within 60 days. Upon completion of a demo/ evaluation test period, units must be returned or purchased within 30 days. An invoice will be generated for payment on any unit(s) not returned within 30 days after the demo/ evaluation period has expired. The customer must pay for the non-compliant product(s) return transportation costs to Transition Networks for evaluation of said product(s) for repair or replacement. Transition Networks will pay for the shipping of the repaired or replaced in-warranty product(s) back to the customer (any and all customs charges, tariffs, or/and taxes are the customer's responsibility). Before making any non-warranty repair, Transition Networks requires a $ charge plus actual shipping costs to and from the customer. If the repair is greater than $200.00, an estimate is issued to the customer for authorization of repair. If no authorization is obtained, or the product is deemed not repairable, Transition Networks will retain the $ service charge and return the product to the customer not repaired. Non-warranted products that are repaired by Transition Networks for a fee will carry a 180-day limited warranty. All warranty claims are subject to the restrictions and conventions set forth by this document. Transition Networks reserves the right to charge for all testing and shipping incurred, if after testing, a return is classified as "No Problem Found." THIS WARRANTY IS YOUR ONLY REMEDY. NO OTHER WARRANTIES, SUCH AS FITNESS FOR A PARTICULAR PURPOSE, ARE EXPRESSED OR IMPLIED. TRANSITION NETWORKS IS NOT LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSSES, INCLUDING LOSS OF DATA, ARISING FROM ANY CAUSE OR THEORY. AUTHORIZED RESELLERS ARE NOT AUTHORIZED TO EXTEND ANY DIFFERENT WARRANTY ON TRANSITION NETWORKS'S BEHALF. Customer Pays Non-Compliant Return Costs The customer must pay the non-compliant product(s) return transportation cost to Transition Networks for evaluation of said product(s) for repair or replacement. Transition Networks will pay for shipping the repaired or replaced in-warranty product(s) back to the customer (any and all customs charges, tariffs, or/and taxes are the customer s responsibility). Page 21 of 23

22 Non-Warranty Repair Costs Before making any non-warranty repair, Transition Networks requires a $200 charge, plus actual shipping costs to and from the customer. If the repair is greater than $200, an estimate is issued to the customer for authorization before making the repair. If no authorization is obtained, or the product is deemed not repairable, Transition Networks will retain the $200 service charge and return the product to the customer not repaired. Repaired Non-Warranty Products Non-warranted products repaired by Transition Networks for a fee will carry a 180-day limited warranty. All warranty claims are subject to the restrictions and conventions set forth by this document. Transition Networks reserves the right to charge for all testing and shipping incurred, if after testing, a return is classified as No Problem Found. Page 22 of 23

23 Transition Networks Red Circle Drive Minnetonka, MN USA Tel: or Fax: Copyright 2011, 2012 Transition Networks All rights reserved. Printed in the U.S.A. SGPAT10xx /100/1000Base-T to 1000Base-SX/LX PoE PSE+ GbE Media Converter User Guide, Rev. A Page 23 of 23