PureGain PG1600P. Data Sheet. Fixed Gain, Compact EDFA with Digital Control Electronics. Contents: Features:

Transcription

1 PureGain PG1600P Fixed Gain, Compact EDFA with Digital Control Electronics Features: The PureGain PG1600P Optical Amplifier Series combines state-of-the-art electronics, superior optical performance, a feature-rich control language and a compact form factor to deliver the lowest-cost amplifier solution for ensuring resilient 40G networks. As a low-noise, single-channel pre-amplifier, proprietary digital control electronics suppress potentially costly power transients to protect detectors and stabilize received power in high-speed networks. The patented digital control system also minimizes thermal dissipation requirements, enabling higher port density and lower operating cost. The PureGain PG1600P series is initially available in a C-Band model with output power up to 17 dbm. Contents: Description... 1 Features... 1 Applications... 1 Key Optical Specifications... 2 Power Transient Suppression Performance... 2 Key Environmental Specifications... 2 Key Control and Electrical Specifications... 3 Software Functions, Monitors and Alarms... 3 Optical/Electrical Schematic... 4 Electrical Pin Assignments... 4 Optical Pigtails... 5 Mechanical Footprint... 5 Complementary Amplifier Products... 6 Oasis Control Architecture Fully Integrated Control Electronics with Output Power Transient Control Suppresses Power Transients to Protect High Speed Transponders Digital Control System with Adaptive Thermal Management Output Power up to 17 dbm RS232 or I 2 C Command Interface with Monitoring, Alarms and Safety Shut-Down Small Package (70 x 90 x 15 mm) Applications 10G and 40G Metro Regional, Long- Haul and Ultra Long-Haul Networks Single-Channel and DWDM Networks Amplification at Optical Add/Drop nodes Transmitter and Receiver Amplification

2 Key Optical Specifications Optical performance specifications vary depending on the optical design. Specifications presented here are based on a typical design. Oclaro can customize the optical design of the Pure Gain PG1600P series to meet a wide range of custom requirements. Parameter Part Number Units Wavelength Range nm Input Channels 1 Input Power Range -20 to +5 dbm Input Power Monitor Accuracy -0.5 to +0.5 db Output Power +3.0 to dbm Output Power Monitor Accuracy -0.5 to +0.5 db Noise Figure (Maximum) for Gain 28dB 4.7 db Polarization Dependent Gain (Maximum) 0.5 db Polarization Mode Dispersion (Maximum) 0.5 ps Power Transient Supression Performance Parameter Part Number Units Transient Speed for Input power variation 50 (Minimum) μs Output power variation (Maximum) for Input power variation = 3dB 0.6 db Output power variation (Maximum) for Input power variation = 5dB 1.2 db Output power variation (Maximum) for Input power variation = 7dB 2.0 db Transient settling time 1000 µs Key Environmental Specifications Parameter Min Max Unit Operating Case Temperature Range C Storage Temperature Range C Operating Humidity % RH Note 1. Non-condensing. 2

3 Key Control and Electrical Specifications Parameter Part Number Units Power Supply Voltage V Power Consumption, Maximum value over life and operating temperature 5 W Startup Surge Current (10ms duration from startup) 10 A Cold Startup Time 20 Sec Software Functions, Monitors and Alarms The software interface of the PureGain PG1600P Series is based on Oclaro s Optical Amplifier Command Set, providing extensive control and monitoring functions. Functions Monitors Alarms In-Service Firmware Upgrades Auto Shut Down Output Power Control Mode Power Transient Suppressed Output Power Control Mode Pump Current Control Mode Eye-Safe Power Mode Non-volatile event log Total Input Power Total Output Power Pump Status Module Temperature Loss-of-Signal Alarm Low Output Power Alarm Module Temperature Alarm Pump Temperature Alarm Pump Bias Alarm 3

4 Optical/Electrical Schematic Electrical Pin Assignments The electrical interface is via one 2-millimeter pitch, 30-pin socket (Samtec p/n: SMM H-D-LC) Pin Description Pin Description 1 Power Supply 2 Power Supply 3 No internal connection 4 No internal connection 5 Ground 6 Ground 7 Serial Input 8 Serial Output 9 Ground 10 Ground 11 Reserved for future use 12 Reset 13 Amplifier Disable 14 Output Power Mute 15 EDFA Case Temperature Alarm 16 Common alarm 17 Pump Temperature Alarm 18 Pump Current Alarm 19 Loss of Input Power Alarm 20 Output Power / Gain Alarm Analog ground (Optional) Input power monitor analog output (Optional) / I 2 C SCL (Optional) 25 Ground 26 Ground 22 Analog ground (Optional) 27 Reserved for future use 28 No internal connection 29 Power Supply 30 No internal connection 24 Input power monitor analog output (Optional) / I 2 C SCL (Optional) 4

5 Optical Pigtails Fiber Type Corning SMF-28 or equivalent Pigtail Buffer diameter 900 µm Pigtail Length > 1000 mm Pigtail Colors Blue (input), Red (output), Black (monitors) Connector Type No connector Mechanical Footprint Note 1: Dimensions are in inches; dimensions in brackets are in millimeters. 5

6 RoHS Compliance Oclaro is fully committed to environment protection and sustainable development and has set in place a comprehensive program for removing polluting and hazardous substances from all of its products. The relevant evidence of RoHS compliance is held as part of our controlled documentation for each of our compliant products. RoHS compliance parts are available to order, please refer to the ordering information section for further details. Ordering Information: PG1600P FC/UPC connector supplied as standard. This connector is present for testing purposes only. It is expected to be removed by the customer to allow connection splicing. Evaluation Board Available on request. Complementary Amplifier Products PowerShaper PS3200 Dispersion Compensator for High-Dispersion Applications PowerShaper PS3300 Dispersion Compensator for Terminal Applications Patents This product is protected by US patent numbers 5,638,204, 6,144,486, 6,359,330, 6,414,788, 6,525,873, 6,528,329, 6,631,027, 6,782,024, 6,798,815, 6,836,355, 6,837,075, 6,943,937, 7,110,167, 7,173,953 and 7,218,659 and other patents and applications pending worldwide. Contact Information www. Important Notice Performance figures, data and any illustrative material provided in this data sheet are typical and must be specifically confirmed in writing by Oclaro before they become applicable to any particular order or contract. In accordance with the Oclaro policy of continuous improvement specifications may change without notice. Further details are available from any Oclaro sales representative. INVISIBLE LASER RADIATION AVOID EXPOSURE TO BEAM CLASS 1M LASER PRODUCT PG-1600P September 2012 Oclaro Oclaro the Oclaro, Inc. logo, and all other Oclaro, Inc product names and slogans are trademarks or registered trademarks of Oclaro, Inc. in the U.S.A. or other countries. Information in this datasheet is subject to change without notice. Maximum Power 28 mw / +14.5dBm Wavelength nm REFERENCE IEC Edition 2.0 6