2x2 Video Wall - NEC P Series Displays - Installation Guide

Transcription

1 2x2 Video Wall - NEC P Series Displays - Installation Guide Materials Checklist Suggested Tools for Installation Supporting Documents NEC P Series LCD (x4) OPS Media Player (x1) OPS Media Player Caddie (x1) Option board slot cover (x1) 2x2 Video Wall Mount (x1) 6 Shielded Ethernet cable (x1) 6 Display Port cable (x4) 6 RS232 Control cable (x3) USB Keyboard and Mouse (x1) 6 Outlet Surge Suppressor Velcro Optional: Hauppauge 1950 USB TV tuner Coax Cable (x1) Interactive: USB Hub (x1) Laptop with USB to Serial adapter Drill w/ metal, wood, and mortar bits Phillips head screwdriver Tape Measure Level Socket Set Hex-end wrench set Shims Cable ties for final cable dressing Screen cleaner and lint free cloth for final clean up This is a minimum list - review statement of work to determine all tools needed. Overview Documents NEC P402 NEC P462 NEC P552 OPS Media Player 2x2 Wall Mount TV Tuner Installation Guides OPS Media Player 2x2 Video Wall Mount Hauppauge 1950 USB TV tuner Tile Matrix Configuration Interactive Display Configuration 2x2 Video Wall Mount OPS Media Player with Option board slot cover OPS Media Player Caddie Revised Page 1

2 2x2 Video Wall - NEC P Series Displays - Installation Guide Step 1 - Preparation 1. Verify that installation location is ready (power, network, wall reinforced, adequate ventilation, coax cable if being installed) 2. Open all packages and lay everything out. Make sure all materials are present and there is no visible damage. Installation Tip: If the installation location is not ready or any materials are missing or damaged, call the Rise Display Project Manager for instructions. Revised Page 2

3 Step 2 - Install OPS Media Player 1. Select one of the LCD Displays and install the OPS Media Player per OPS Media Player Installation guide. 2. After installing the OPS Media Player, set display aside. This display will be Display #1. 3. If this is NOT an interactive display, insert the keyboard and mouse USB dongle into a USB port on the OPS Media Player now. If the display is interactive, you will install this dongle later. Step 3 - Install 2x2 Video Wall Mount and LCD Displays 1. Install 2x2 video wall mount and LCD Displays per 2x2 Wall Mount Installation guide. Installation Tip: Leave adequate space between the left and right sides to access the rear of video wall and slide the displays together after cabling is completed. Revised Page 3

4 Connect all Cables Step 4A - RS232 Cables 1. Install RS232 Null Modem cables. Refer to RS232 Wiring Diagram at right. Front of Display Installation Tip: RS232 ports are labeled IN and OUT on display - double check to ensure you have cable connected to correct port - The RS232 OUTPUT ports are the ports closest to the wall when display is installed. Revised Page 4

5 Step 4B - Display Port Cables 1. Install Display Port cabling. Refer to Display Port (DP) Wiring Diagram at right. Front of Display Installation Tip: Display Port (DP) ports are labeled IN and OUT on display - double check to ensure you have cable connected to correct port - As you are facing the front of the screen, the Display Port IN is on the left. Revised Page 5

6 Step 4C - USB Cables (Interactive Only) If Video Wall is NOT interactive, skip this step 1. Install USB Hub behind display #1 below the OPS PC to allow access later. 2. Interactive screens come with a USB cable hardwired to the back - connect the USB cable from each display to the USB outputs on the USB Hub. 3. Connect USB cable from USB Hub input to one of the USB ports on the OPS Media Player 4. Insert Keyboard and Mouse USB dongle in USB port on USB hub. Revised Page 6

7 Step 4D - Power and Network 1. Connect one end of Ethernet patch cable to customer provided Ethernet jack - you will connect this to the Ethernet connection on the OPS Media Player in display Connect 6 outlet surge suppressor to customer provided AC outlet. You will connect all power cords from the displays and the external TV tuner (if used) to this surge suppressor. Revised Page 7

8 Step 5A - Power up and configuration 1. Make sure the main power switch on each display is ON (The main power switch is located on the back of the display where the power cord connects) 2. Power on the 2x2 display by turning power on to each display individually. 3. Powering on display 1 will automatically power on the OPS Media Player. Installation Tip: Make sure all 4 displays have the input set to Display Port using the remote control. If input is not set to Display Port, monitors will go into power save mode. Important - you should now see the exact same image on all 4 displays Revised Page 8

9 Step 5B - Set up Tile Matrix 1. Set up Tile Matrix on 2x2 video wall. This is done using the on screen menus on the NEC displays. 2. Refer to Tile Matrix configuration document for details. Revised Page 9

10 Step 5C - Set up Individual Display ID Using the remote control, set each of the 4 displays with their unique display ID and Primary/Secondary status as follows: 1. Select Menu button to get on-screen menu to display 2. Scroll over to select MULTI-DISPLAY function 3. Scroll to highlight MONITOR ID function 4. Scroll to select MONITOR ID 5. For Display #1, select ID No. 1, for Display #2, select ID No. 2, for Display #3, select ID No. 3 and for Display #4, select ID No. 4 so that each display has its own unique ID No. 6. Each of the Displays will remain in Group A 7. Now scroll down to IR CONTROL 8. For Display #1 ONLY - set IR CONTROL to PRIMARY 9. For all other displays - set IR CONTROL to SECONDARY Set Monitor ID Installation Tip: To control displays after setting this up, push the DISPLAY button on the remote then push the number on the keypad for the display you wish to control. So to control display 3, push DISPLAY, then the number 3. Now you will be controlling display #3 Set Primary/Secondary status Revised Page 10

11 Step 6 - Install and Configure TV If no TV is to be installed, skip this step Connect Hauppauge USB TV tuner connections. 1. Coax cable from client network to coax connector on tuner labeled TV. 2. USB connection from TV tuner to open USB slot on OPS Media Player. 3. Power - Plug AC adapter into power strip and connect to the Power In (+6V) on tuner. There is no power switch on the tuner, it will power on when plugged in - check red LED power indicator to make sure tuner is on. 4. Locate TV tuner behind display out of sight just above the OPS Media Player. Once you have placed the tuner behind the screen and verified that it is out of sight, remove it briefly and place a bit of the supplied velcro on the back of the tuner and on the wall where it will go. Then tuck the TV tuner behind the display out of sight, secure with velcro and tie all cables neatly out of view. 5. All drivers and WinTV come installed and preconfigured on the OPS Media player and no configuration is needed. If needed - consult the external USB TV Tuner guide Hauppauge external USB TV tuner installation guide Revised Page 11

12 Step 7 - Interactive Screen Configuration If Video Wall is NOT interactive, skip this step The Rise Display OPS Media Player was sent with all required touch drivers already installed. Touch capability should already be working on each screen after you made the proper connections in step 4C. At this point, you just need to set the ID for each screen and calibrate as follows: From the windows desktop click on Start More details can be found in the MicroTouch Software User guide here: Interactive Display Configuration Guide Step 8 - Display Configuration 1. Reboot display by restarting Windows. 2. Set up Power Schedule for displays if client wishes - using on screen menus. (see page 27 of the NEC users manual) 3. Disable buttons on NEC Displays. To activate the control key lock function, press both and (on the display, not the remote) and hold down simultaneously for more than 3 seconds. To resume user mode, press both and hold simultaneously for more than 3 seconds. 4. Put Velcro on remote and attach to the back of the left side (as you are facing the front of the video wall) of display #3 Revised Page 12

13 Step 9 - Wrap Up 1. Remove all trash and extra parts - dispose of properly 2. Clean up work area - wipe down displays 3. Provide 3 remote controls, keyboard and mouse to client. 4. Obtain written sign off from customer 5. Take pictures of installation and to Sales@risedisplay.com and copy the Rise Display Project Manager. 6. Call the Rise Display Project Manager to review installation Revised Page 13