Changes or modifications not expressly approved by InFocus Corporation may void authority to operate the equipment.

Transcription

1 Model: 2101

2 Declaration of Conformity Manufacturer: InFocus Corporation SW Parkway Avenue Wilsonville, OR We declare under our sole responsibility that this device conforms to the following directives and norms: EMC Directive 2004/108/EC, EMC: EN55022, EN55024, EN , EN FCC Warning This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by InFocus Corporation may void authority to operate the equipment. Canada This Class A digital apparatus complies with Canadian ICES-003. Cet appareil numerique de la classe A est conforme a la norme NMB-003 du Canada.

3 Contents Introduction... 3 DisplayLink Extender Product Contents... 3 Requirements... 3 About the DisplayLink Extender... 3 Installation guide... 6 Connecting the Computer module to the Projector module... 6 Installing the Projector module... 7 Installing the Computer module... 7 Troubleshooting... 8 Specifications Limited Warranty Limitation of Liability Obtaining Warranty Service Technical Glossary... 14

4 Introduction The instructions in this guide assume a general knowledge of computer installation procedures, and familiarity with USB cabling requirements. note NOTE: Notes provide additional information that could be useful. CAUTION: Cautions provide important information about an operational requirement. DisplayLink Extender Product Contents Your DisplayLink Extender is packaged with: DisplayLink Extender Quickstart Guide Computer module Projector module Projector module power cord Requirements To complete the installation, you will also require the following items that are not included with the product: USB 2.0 compatible computer (Windows or Mac) with a USB compliant operating system An InFocus or ASK Proxima projector with a DisplayLink connector The USB cable included with your projector (or a high-quality USB 2.0-compliant USB type-a to mini-b cable, no more than 2m in length). CAT 5 Unshielded Twisted Pair (UTP) cable with two RJ45 connectors (if using surface cabling), OR, CAT 5 cabling with two information outlets and two CAT 5 patch cords with RJ45 connectors (if using premise cabling) note All references to CAT 5 cable in this document represent the minimum requirement. Category 6 or better or STP cable may be substituted. About the DisplayLink Extender The DisplayLink Extender enables users to extend beyond the standard 5m cable limit for USB peripheral devices. With the DisplayLink Extender, the projector can be located up to 100 meters from the computer. The DisplayLink Extender is composed of two individual modules; the computer module and the projector module. 3

5 The Computer module The Computer module connects to the computer using the attached USB cable. Power for this module is provided by the computer s USB port. Back View Top View ITEM TYPE DESCRIPTION 1 Power LED (Blue) LED turns on when power is supplied. Off when no power is supplied. 2 Host LED (Green) LED turns on when DisplayLink Extender is installed properly. 3 Link Port (RJ45) Accepts RJ45 connector for CAT 5 cabling (or better). 4 Link LED (Green) on RJ45 Indicates connectivity between the Computer and Projector modules. LED turns on when link between the Computer and Projector modules is established. Off when there is no link between Computer and Projector modules. 5 Activity LED (Amber) on RJ45 Indicates activity on RJ45 port. LED blinks intermittently when data is transmitted between Computer and Projector modules. 6 Power/Config port Manufacturer use only. 7 USB Type A connector Used to connect the Computer module to the computer. 4

6 The Projector Module The Projector module provides a USB Type A port for projectors. The Projector module allows you to connect one projector directly. Additional devices may be connected by attaching USB hubs to the projector module. The Projector module is powered by the projector via the included power cord. Top View Front View Rear View ITEM TYPE DESCRIPTION 1 Power LED (Blue) LED turns on when power is supplied. Off when no power is supplied. 2 Host LED (Green) LED turns on when DisplayLink Extender is installed properly. 3 Link Port (RJ45) Accepts RJ45 connector for CAT 5 cabling (or better). 4 Link LED (Green) on RJ45 5 Activity LED (Amber) on RJ45 Indicates connectivity between Computer and Projector modules. LED turns on when link between Computer and Projector modules is established. Off when there is no link between Computer and Projector modules. Indicates activity on RJ45 port. Blinks intermittently when data is transmitted between Computer and Projector. 6 Power/Config port Connects to the included Projector module power cord. 7 Device Port (USB Type A port) USB device connection. The Power/Config port is only for use with the included power cord. No USB devices can be connected/used on the port. 5

7 Installation guide PC DisplayLink To Computer To Projector +5V DC Before you can install the DisplayLink Extender, you need to prepare your site. 1. Determine where the computer is to be located and set up the computer. 2. Determine where you want to locate the Projector(s). 3. If you are using surface cabling, the DisplayLink Extender supports a maximum distance of 100m. OR USB 2.0 (CAT 5) Extension Max Length 100m If you are using premise cabling, ensure CAT 5 cabling is installed between the two locations, with CAT 5 information outlets located near both the computer and the projectors. Connecting the Computer module to the Projector module note To ensure proper operation, it is recommended that only CAT 5 or better, Unshielded Twisted Pair cabling be used to connect the Computer module to the Projector module. The cabling must have a straight-through conductor configuration with no crossovers, and must be terminated with 8 conductor RJ45 connectors at both ends. The combined length of any patch cords using stranded conductors must not exceed 10m. With Surface Cabling 1. Plug one end of the CAT 5 cabling (not included) into the Link port (RJ45) on the Computer module. 2. Plug the other end of the CAT 5 cabling into the Link port (RJ45) on the Projector module. With Premise Cabling 1. Plug one end of a CAT 5 patch cord (not included) into the Link port (RJ45) on the Computer module. 2. Plug the other end of the patch cord into the CAT 5 information outlet near the Host computer. 3. Plug one end of the 2 nd CAT 5 patch cord (not included) into the Link port (RJ45) on the Projector module. 4. Plug the other end of the 2 nd patch cord into the CAT 5 information outlet near the USB device. note The maximum length of the CAT 5 cable, including patch cords, must not exceed 100 meters. The combined length of any patch cords using stranded conductors must not exceed 10m. 6

8 Installing the Projector module 1. Place the Projector module near the Projector. 2. Plug the Projector module power cord between the projector module and the projector s +5VDC connector. 3. Connect the Projector module to the projector s DisplayLink connector using the USB cable that was included with your projector (or a high-quality USB 2.0-compliant USB type-a to mini-b cable, no more than 2m in length). Only use the power cord supplied with DisplayLink Extender. Use of substitute power cords may cause permanent damage to the system and will void the warranty. Installing the Computer module 1. Place the Computer module near the computer. 2. Plug the USB Type A connector on the Computer into a USB port on the computer. 7

9 Compatibility The DisplayLink Extender complies with USB 2.0 specifications governing the design of USB devices. InFocus Corporation does not, however, guarantee that all USB devices are compatible with the DisplayLink Extender as there are a number of different configurations that may impact the operation of USB devices over extended distances. Troubleshooting The following table provides troubleshooting tips. The topics are arranged in the order in which they should be executed in most situations. If you are unable to resolve the problem after following these instructions, please contact technical support for further assistance. PROBLEM CAUSE SOLUTION All LEDs on Computer module are off. The Computer module is not receiving enough power from the USB port or the a computer AC adapter. 1. Ensure that the USB Type A connector from the Computer module to the computer is properly inserted directly in a USB port. 2. Move the Computer USB Type A connector to another USB port on the computer. All LEDs on Projector module are off The Projector module is not receiving power from the projector 1. Ensure that the power cord is properly connected to both the Projector module and the projector. Link LEDs on Computer module and Projector module are off. There is no connection between the Computer module and Projector module. 1. Ensure that a CAT 5 cable (or better) with straight-through conductors is connected between the Computer module and Projector module. 2. If the CAT 5 cable is defective, connect a short CAT 5 patch cord between the Computer module and Projector module to determine if the original CAT 5 cable is defective. 8

10 PROBLEM CAUSE SOLUTION Link LED on Computer module is on, Host LED on Computer module is off DisplayLink Extender modules were working but the Host LED on Projector module is suddenly blinking All LEDs on both the Computer module and Projector module are on but the USB device does not operate correctly or is detected as an Unknown Device in the operating system. The computer is not powered on. The Computer module is not connected to the computer (when used with the optional Computer AC adapter) The computer does not support USB hubs. The DisplayLink Extender is malfunctioning The Projector module is in suspend mode. The operating system may put the DisplayLink Extender in suspend mode when the computer is put into a Suspend/Standby state or when no projector is attached. The projector is malfunctioning. The computer does not recognise the projector. The application software for the device is not operating. The DisplayLink Extender is malfunctioning. 1. Disconnect the Projector module from the DisplayLink port and power connector on the projector. 2. Disconnect the Computer module from the computer. 3. Reconnect the Computer module to the computer. 4. Reconnect the Projector module to the DisplayLink port and to the power cord. 5. In the Universal Serial Bus controllers section of Device Manager, check that the DisplayLink Extender is recognised as a Generic USB Hub. 1. Recover/Resume the operating system from Suspend/Standby mode (see your operating System s documentation). 2. Connect a projector to the Projector module.. 1. Disconnect the Computer module from the computer. 2. Connect the projector directly to the USB port on the computer. 3. If the projector does not operate properly, consult the projector user documentation. 4. Update your system BIOS, chipset or USB Host controller drivers from your System/Mother board manufacturer s website. 5. If the projector operates properly when directly connected to the computer, connect another USB device to the Computer module. Connect the DisplayLink Extender to the computer. 6. If the other USB device does not operate, the DisplayLink Extender may be malfunctioning. Contact InFocus support for assistance If the other USB device operates properly, the projector may be malfunctioning. Contact InFocus support.

11 NOTES 10

12 Frequently Asked Questions Please visit InFocus s website for answers to FAQs: Specifications Range USB hub support USB host support EHCI (USB 2.0) Maximum projectors supported (Incl. USB Hubs) AC adapter connector Power available to USB device at Projector module USB cable length (Computer to Host computer) Computer module USB connector Computer module Link connector Projector module Link connector Projector module USB connector Computer module dimensions Computer module weight 100 metres over Cat 5 (or better) cable Any single chain can include up to 4 Certified High Speed USB 2.o hubs plus one DisplayLink Extender. 14 projectors including any additional Certified High Speed USB 2.0 hubs connected to the Projector. 8-pin custom connector 500 ma 0.15 meters (0.49 ft) 1 x USB Type A connector 1 x RJ45 1 x RJ45 1 x USB Type A port 44 mm x 87 mm x 24 mm (1.72 x 3.43 x 0.95 ) 0.06 kg ( 0.13 lbs) Computer module power consumption 500 ma Maximum Projector module dimensions 44 mm x 87 mm x 24 mm (1.72 x 3.43 x 0.95 ) Projector module weight Projector module power consumption System shipping weight 0.05 kg ( 0.11 lbs) Approx. 500 ma (No Load). 1A (Full load) 0.18 kg (0.40 lbs) Operating temperature range 0 C 50 C Regulatory testing FCC Class A, ICES-003, EN55022, EN

13 Limited Warranty InFocus Corporation warrants the DisplayLink Extender shall be free from significant defects in material and workmanship for a period of one year from the date of purchase. Limitation of Liability IT IS UNDERSTOOD AND AGREED THAT INFOCUS LIABILITY SHALL NOT EXCEED THE RETURN OF THE AMOUNT OF THE PURCHASE PRICE PAID BY PURCHASER Where applicable national law prohibit the exclusion or limitation of liability, InFocus excludes or limits its liability to the maximum extent permitted by national law. Limitation on Bringing Action - No action, regardless of form, arising out of the agreement to purchase the Product may be brought by purchaser more than one year after the cause of action has accrued. Governing Law - Any action, regardless of form, arising out of the agreement to purchase the Product is governed by the laws of the state of Oregon, USA. Mandatory Arbitration - Any action, regardless of form, arising out of the agreement to purchase the Product is subject to mandatory arbitration. THIS WARRANTY DOES NOT AFFECT YOUR LEGAL RIGHTS UNDER APPLICABLE NATIONAL LAWS RELATING TO THE SALE OF CONSUMER PRODUCTS. Trademark Information InFocus, In Focus, INFOCUS (stylized) and ASK Proxima are either registered trademarks or trademarks of InFocus Corporation in the United States and other countries. DisplayLink is a trademark or registered trademark of DisplayLink Corporation. Mac is a trademark or registered trademark of Apple Corporation. Windows is a trademark or registered trademark of Microsoft Corporation. Other trademarks mentioned herein are the property of their respective owners and are referenced for information only. Any reference does not imply affiliation, recommendation or endorsement by or between the respective trademark owners and InFocus Corporation. Product specifications, terms, and offerings are subject to change at any time without notice. 12

14 Obtaining Warranty Service During the Limited Warranty period, to exercise the Limited Warranty, the purchaser must first contact 1) InFocus, 2) a service facility authorized by InFocus or 3) the place of original purchase. InFocus Customer Service in the Americas or or In Europe, Middle East, and Africa +31 (0) , and in Asia Pacific To help us serve you better, please include the following information with your technical support request: Host computer make and model Type of operating system installed (e.g. Windows XP, Mac OS X, etc.) Projector model(s) attached to the DisplayLink Extender Description of the installation, including the type of hubs being used, if any Description of the problem 13

15 Technical Glossary Category 5 (CAT 5) Network Cabling Category 5 cable is commonly also referred to as CAT 5. This cabling is available in either solid or stranded twisted pair copper wire variants and as UTP (Unshielded Twisted Pair) or STP (Shielded Twisted Pair). UTP cables are not surrounded by any shielding making them more susceptible to electromagnetic interference (EMI). STP cables include shielding over each individual pair of copper wires and provides better protection against EMI. CAT 5 has been succeeded by CAT 5E cabling which includes better support for high speed communications and reliability. RJ45 The Registered Jack (RJ) physical interface is what connects the network cabling (CAT 5) to the Computer and Projector module. You may use either the T568A scheme (Table 1) or the T568B scheme (Table 2) for cable termination as the DisplayLink Extender uses all four pairs of the cable. RJ45 connectors are sometimes also referred to as 8P8C connectors. RJ45 Pin Positioning Table 1 - T568A Wiring Table 2 - T568B Wiring PIN PAIR WIRE CABLE COLOR PIN PAIR WIRE CABLE COLOR WHITE/GREEN WHITE/ORANGE GREEN ORANGE WHITE/ORANGE WHITE/GREEN BLUE BLUE WHITE/BLUE WHITE/BLUE ORANGE GREEN WHITE/BROWN WHITE/BROWN BROWN BROWN Pair 2 Pair 3 Pair 1 Pair 4 Pair 2 Pair 3 Pair 1 Pair W-G G W-O BL W-BL O W-BR BR W-O O W-G B W-BL G W-BR BR 14

16 InFocus Corporation SW Parkway Ave Wilsonville, Oregon Tel: Fax: