IMPORTANT SAFETY INSTRUCTIONS

Transcription

1 READ AND FOLLOW ALL SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION IMPORTANT SAFETY INSTRUCTIONS WARNING RISK OF SEVERE INJURY OR DEATH To reduce the risk of death, injury or property damage from fire, electric shock, cuts, abrasions, falling parts, and other hazards: Read all warnings and instructions included with and on the fixture box and all fixture labels. Installation and service should be performed by a qualified licensed electrician. Maintenance must be performed by a person familiar with the construction and operation of this product and any hazards involved. All applicable codes and ordinances must be followed. Read this document before installing, servicing, or maintaining this equipment. These instructions do not cover all installation, service, and maintenance situations. If your situation is not covered, or if you do not understand these instructions or additional information is required, contact Acuity Controls. WARNING RISK OF ELECTRIC SHOCK Before installing, servicing, or maintaining this equipment, follow these general precautions. To reduce the risk of electrocution: Disconnect or turn off power before installation or servicing. Make sure the equipment is properly grounded. Make all electrical connections in accordance with the National Electrical Code (NEC) and any applicable local code requirements. WARNING RISK OF FIRE To reduce the risk of fire: Use supply conductors with a minimum operating temperature rating as specified. Do not exceed maximum wattage, ratings, or published operating conditions. Follow all manufacturer s warnings, recommendations and restrictions to ensure proper operation. WARNING RISK OF PERSONAL INJURY To reduce the risk of personal injury from cuts, abrasions: Wear gloves and safety glasses at all times when installing, servicing or performing maintenance. WARNING RISK OF PRODUCT DAMAGE Electrostatic Discharge (ESD) will damage electronic equipment. Do not attempt to open or service electronic equipment without proper ESD precautions. Do not touch electronic components. ESD damage can occur. Do not change or alter internal wiring or circuitry. Acuity Controls assumes no responsibility for claims arising out of improper or careless installation or handling of this product. Failure to follow any of these instructions could void product warranty. For a complete listing of product Terms and Conditions, please visit Always read complete installation instructions prior to installation SAVE THESE INSTRUCTIONS Page 1

2 Fresco FCS AVI allows 3rd party system controllers to interface with a Fresco System, using either or bidirectional communication. The FCS AVI controls up to 36 lighting scenes and/or levels. The FCS AVI is provided in a painted steel enclosure with a prewired power supply and detachable terminal blocks for simple field installation. Before You Start 1. Disconnect power prior to installation or servicing. 2. Mount and install FCS AVI in accordance with the National Electrical Code and any other codes which may apply. 3. Use only as intended. 4. Use only accessories recommended by Acuity Controls. 5. Use only at the voltage listed on the product and component labels. Important Installation Notes 1. Ambient Conditions: Maximum Ambient Temperature: 104 F/40 C Minimum Ambient Temperature: 32 F/0 C Relative Humidity:10-90% Non condensing Designed for permanent interior installation 2. The FCS AVI is rated for 120 or 277V, 60 Hz operation. 3. Use only copper conductors with 90 C insulation rating or higher. 4. FCS AVI should be mounted to an appropriate surface with 4 screws. Make sure the supporting surface will safely support the combined load of the equipment and all attached hardware and components. Overview Digitally control any fixture type on the Fresco network, including DMX-512. An on-board mechanical switch allows selection between or on the data output port. Baud Rate Options: 1200, 2400, 4800, 9600, 19200, 38400, 57600, and Bidirectional communication for control and status. Configure and control up to 36 Fresco lighting inputs and outputs. Electrical isolation to prevent faults from further damaging system components acuitycontrols.com FCS AVI 120/277 WARNING TO AVOID THE RISK OF FIRE AND SHOCK, DOORS MUST REMAIN CLOSED AT ALL TIMES Fresco FCS AVI Page 2

3 FCS AVI Installation and Wiring 1. MOUNT FCS AVI Mount the FCS AVI to a wall using the 4 mounting holes. The mounting holes are sized for 1/4" (6 mm) screws. Use the appropriate mounting screws for the wall type being anchored to. See Figures 1 and 2 for details. 2. CONNECT POWER Connect 120 or 277 VAC to the input terminal block power. 3. CONNECT FRESCO CONTROL Connect the Fresco Control Network () to the connector on the FCS AVI. 4. CONNECT / Connect either the or port to the desired 3rd party system. (Both ports cannot be used simultaneously) 5. APPLY The device at each end of the Fresco station network () and network must be terminated for proper operation. Operation The following LED status indicators will remain lit during normal operation Primary 3.3V Isolated Power The following LED status indicators will blink when receiving/transmitting data Interface Commands Please refer to the "FCS AVI" Interface Commands ( ) for command description and examples. Shade Integration The following shade control interfaces are supported, allowing control of compatible shades: Lutron QSE-CI-NWK-E Somfy Connect UAI MechoSystems MNI Warnings The FCS AVI can be powered by 120 or 277 VAC. DO NOT connect the incoming voltage (either 120 or 277 VAC to the incorrect transformer lead. Severe damage and/or malfunction will result The FCS AVI provides termination circuits for both the Fresco station network () and port. Switch 1 terminates the port and Switch 2 terminates the port. The devices at each end of the network must be terminated for proper operation. Switch 4 assigns the data output port's mode of operation, either or. Switch 4 must be set correctly for the desired mode of operation. NEVER connect AC line voltage to any connector on the FCS AVI circuit board. Catastrophic damage will result Fuse Replacement The FCS AVI circuit board is protected by a fuse. Replace ONLY with 250mA, 350VAC, 5.1 x 13.8mm Quick Acting fuse. Incorrect fuses will fail to protect the FCS AVI as intended. Page 3

4 3.11 (79) 6.95 (176) 0.26 (6.6mm) DIAMETER 2.51 (64) 8.25 (201) 6.75 (171) 8.25 (201) FCS AVI Dimensions (in/mm) 3.11 (79) 120/277VAC INPUT 1/2 " CONDUIT KNOCKOUT (TYPICAL ALL) GROUND LUG FOR EQUIPMENT GROUNDING ONLY NEUT 120V 277V FACTORY WIRING HARNESS END OF SWITCH FRESCO SWITCH or SELECTOR SWITCH FRESCO CONTROL CONNECTOR CONNECTOR SERIAL CONNECTOR Figure 1 - FCS AVI Details FUSE Page 4

5 LINE VOLTAGE CONDUIT ENTRY ONLY ALL KNOCKOUTS FOR 1/2" CONDUIT FOR EQUIPMENT GROUNDING ONLY NEUT 120V 277V LOW VOLTAGE CONDUIT ENTRY ONLY. NO LINE VOLTAGE LOW VOLTAGE CONDUIT ENTRY ONLY. NO LINE VOLTAGE Figure 2 - FCS AVI Conduit Entry Page 5

6 D6 D10 Installation Instructions GROUND LINE VOLTAGE INPUT POWER. CONNECT TO 120 OR 277VAC or SWITCH: SELECT DESIRED FUNCTION FOR EQUIPMENT GROUNDING ONLY NEUT 120V 277V SWITCH: FRESCO () (DEFAULT) SWITCH: 3rd PARTY ON SW2 SW4 DATA- DATA+ SW1 ON PRIMARY 3.3v D5 D4 D3 MIDDLE OF NO ON END OF APPLIED (DEFAULT) STATUS F1 ON D+ D- TXD RXD 250mA 350VAC FUSE 2JQ 250-R 5.1mm x 13.8mm QUICK ACTING 23VAC NO LINE VOLTAGE MIDDLE OF NO END OF APPLIED (DEFAULT) /GROUND TXD* RXD* TO 3rd PARTY DEVICES TO 3rd PARTY DEVICES DATA - DATA + RXD TXD WALLSTATION WALLSTATION DATA - WALLSTATION DATA + FRESCO WALLSTATION : SYA CABLEA4 TO FRESCO CONTROL DEVICES * Make sure to wire TXD to RXD and vice versa. Figure 3 - FCS AVI Wiring Details Page 6

7 bus PC or other 3 rd party device AVI Fresco Touchscreen controller Connect to compatible port or Figure X. FCS AVI connected to 3rd party device Shades bus AVI Fresco Touchscreen controller 3 rd party shade interface /485 Connect to compatible port or Figure Y. FCS AVI connected to supported shade interface Shades bus AVI Fresco Touchscreen controller 3 rd party shade interface /485 Connect to compatible port or bus PC or other 3 rd party device AVI Connect to compatible port or Figure Z. System with AVIs used for 3rd party integration and shade control Page 7

8 FCS AVI Troubleshting Verify wiring to TX, RX, and connector from 3rd party system. FCS AVI TXD goes to EXTERNAL RXD FCS AVI RXD goes to EXTERNAL TXD FCS AVI goes to EXTERNAL GND As illustrated in figure below if this connector had an adapter and wiring harness connecting to the FCS AVI: Pin 2 would connect to FCS AVI TXD, Pin 3 would connect to FCS AVI RXD, and Pin 5 would connect to FCS AVI. Pin 1: Data Carrier Detect (DCD) Pin 2: Received Data (RXD) Pin 3: Transmit Data (TXD) Pin 4: Data Terminal Ready (DTR) Pin 5: Ground (GND) Gently pull on the wires going to the FCS AVI black communication connectors (RS232, RS485, ) to ensure the wires are making gd contact and are secure. Check the RS232 <-> RS485 selector on the FCS AVI PCBA. If there is a range extender, additional cabling, converter, between third-party system and FCS AVI verify its operation and settings. Can the about command be typed and a response seen? Check the version of the firmware by typing about command. Is any data received upon the startup of the FCS AVI? Verify FCS AVI has driver configured as AVI or LUTRON QSE according to application. Verify baud rate and communications settings. Power cycle the FCS AVI and observe the status LED s. STATUS will be solid green will blink periodically once a second when connected to the / Fresco network. RS232 will blink with data sent / received If configured for RS232 operation send some data on terminal application, observe if the RS232 indicator actuates. If configured for RS232 operation change the baud rate to 9600 (or some other baud rate the FCS AVI is *not* set to). Send some data on terminal application, the RS232 indicator should not actuate while data is being sent. Unplug the connector, observe the status LED will not blink. Unplug the connector, attempt to send data or command and check for response and RS232 or RS485 LED actuate. Change the FCS AVI driver to Lutron QSE, disconnect the RS232 or ensure there is no Lutron QSE controller, verify the RS232 LED will actuate roughly once every 10 seconds. If the RS232 LED is on solid (and apparently no data is being sent), ensure the / GND is connector or swapped with. Use a terminal emulation program such as Tera Term or PuTTY (suggest using Tera Term) for testing command and response or basic communications. Page 8