EN TECHNICAL MANUAL. Audio module Art and Art. 1622L

Transcription

1 EN TECHNICAL MANUAL Audio module Art and Art. 1622L

2 Warning Install the equipment by carefully following the instructions given by the manufacturer and in compliance with the standards in force. Do not tamper with the internal elements offering protection against short circuits and overcurrents. All the equipment must only be used for the purpose it was designed for. Comelit Group S.p.A. declines any responsibility for improper use of the apparatus, for any alterations made by others for any reason or for the use of non-original accessories or materials. All the products comply with the requirements of the 2014/30/EU and 2014/35/EU directives. This is proved by the CE mark on the products themselves. Do not route the riser wires in proximity to power supply cables (230/400V). Installation, mounting and assistance procedures for electrical devices must only be performed by specialised electricians. Disconnect the power supply before carrying out any maintenance procedures. Connect the module support frame to earth (see Fig.) Table of contents Warning... 2 Description... 3 Installation information... 4 Installation with Ikall external unit... 5 Installation with Vandalcom (A) Roma (B) external unit... 6 Vandalcom (A)...6 Roma (B)...6 Button programming... 7 Dip switch programming table... 8 EXAMPLE: dip switch setting for code Special programming Special programming table...11 Operating distances with Art Operating distances...13 Maximum system expansion...13 Wiring diagrams Door-entry phone system with 1 audio port, Ikall series. Switching on/ voltage check with system in standby...14 Door-entry phone system with 2 audio ports, Ikall series...15 Wiring diagram for system with digital call module Art Wiring diagram with safety lock...16 Using the external unit relay on lock-release or actuator control...17 Door open indication use variant...17 Protection device connection variant for line Art Use of RC network for lock filter on relay contacts

3 Description 1. ON DIP ON OFF DIP switches for function programming and setting the user code. 2. Switch for input/output programming. 3. Loudspeaker volume control. 4. Connector for additional module connection. 5. Jumper for managing the RC network for door lock filter on relay contacts. 6. Terminal block for connection: SE electric lock connection COM common relay contact NC normally closed relay contact NO normally open relay contact GND input reference negative for DO-RTE PR programming input DO door opened signal input RTE local lock release input V- power supply negative V+ power supply positive LL bus line connection Signalling LED: call sent (Art. 1622L only). 2. Speaker. 3. Microphone. 4. Signalling LED: system busy (Art. 1622L only). 5. Signalling LED: audio activated (Art. 1622L only). 6. Signalling LED: lock-release activated (Art. 1622L only). 7. Loudspeaker volume control. 3

4 Installation information The system can manage up to 240 users, connecting MAX 100 internal units for each riser and 3 internal units with the same user code. If the additional Art is used, up to 16 internal units can be connected in parallel. If using risers with over 30 Easycom door-entry phones Art. 6228W or Art. 6228B, apply SB2 technology (with mixer Art or Art. 4888C) when installing these risers. Modules Art. 1622/Art. 1622L normally function as a main external unit (timed busy signal). To set them as a secondary external unit (busy signal active for the whole time the riser is in use), set all the selector DIP switches to ON. When a call is transmitted from the external unit, if a busy tone is heard instead of the ringtone, this means communication with another external unit is in progress. In the event of a persistent short-circuit on the bus line, the external unit emits an intermittent signalling tone. Only Art. 1622L is fitted with a signalling LED and the voice messages function. The signalling LEDs (busy, call sent, door opened, communication active) are only available with the faceplates of the kit 33400K. Art. 1622L can only be fitted to single-plate external units with accessory 1250IAL. 4

5 Installation with Ikall external unit 1 2 WHITE OFF BLUE LED O FF LED O FF 3 Nameplate LED lighting selection. 3 2 Alternative microphone position (excluding 4 module entrance panel) open Speaker adjustment 4 5 close 5

6 Installation with Vandalcom (A) Roma (B) external unit white green orange white green 1 2 orange Vandalcom (A) ALTO ALTO orange ALTO white ALTO green 3A 4A 5A Roma (B) orange white green 3B 4B 5B 6

7 Button programming -V +V Set the user code using the dip switches; see Dip switch programming table

8 Dip switch programming table Cod Dip switch ON , ,3 6 2,3 7 1,2, ,4 10 2,4 11 1,2,4 12 3,4 13 1,3,4 14 2,3,4 15 1,2,3, ,5 18 2,5 19 1,2,5 20 3,5 21 1,3,5 22 2,3,5 23 1,2,3,5 24 4,5 25 1,4,5 26 2,4,5 27 1,2,4,5 28 3,4,5 29 1,3,4,5 30 2,3,4,5 31 1,2,3,4, ,6 34 2,6 35 1,2,6 36 3,6 37 1,3,6 38 2,3,6 39 1,2,3,6 40 4,6 41 1,4,6 42 2,4,6 43 1,2,4,6 44 3,4,6 45 1,3,4,6 46 2,3,4,6 47 1,2,3,4,6 48 5,6 Name Cod Dip switch ON 49 1,5,6 50 2,5,6 51 1,2,5,6 52 3,5,6 53 1,3,5,6 54 2,3,5,6 55 1,2,3,5,6 56 4,5,6 57 1,4,5,6 58 2,4,5,6 59 1,2,4,5,6 60 3,4,5,6 61 1,3,4,5,6 62 2,3,4,5,6 63 1,2,3,4,5, ,7 66 2,7 67 1,2,7 68 3,7 69 1,3,7 70 2,3,7 71 1,2,3,7 72 4,7 73 1,4,7 74 2,4,7 75 1,2,4,7 76 3,4,7 77 1,3,4,7 78 2,3,4,7 79 1,2,3,4,7 80 5,7 81 1,5,7 82 2,5,7 83 1,2,5,7 84 3,5,7 85 1,3,5,7 86 2,3,5,7 87 1,2,3,5,7 88 4,5,7 89 1,4,5,7 90 2,4,5,7 91 1,2,4,5,7 92 3,4,5,7 93 1,3,4,5,7 94 2,3,4,5,7 95 1,2,3,4,5,7 96 6,7 Name Cod Dip switch ON 97 1,6,7 98 2,6,7 99 1,2,6, ,6, ,3,6, ,3,6, ,2,3,6, ,6, ,4,6, ,4,6, ,2,4,6, ,4,6, ,3,4,6, ,3,4,6, ,2,3,4,6, , ,5,6, ,5,6, ,2,5,6, ,5,6, ,3,5,6, ,3,5,6, ,2,3,5,6, ,5,6, ,4,5,6, ,4,5,6, ,2,4,5,6, ,4,5,6, ,3,4,5,6, ,3,4,5,6, ,2,3,4,5,6, , , ,2, , ,3, ,3, ,2,3, , ,4, ,4, ,2,4, ,4, ,3,4, ,3,4, ,2,3,4, ,8 Name 8

9 Cod Dip switch ON 145 1,5, ,5, ,2,5, ,5, ,3,5, ,3,5, ,2,3,5, ,5, ,4,5, ,4,5, ,2,4,5, ,4,5, ,3,4,5, ,3,4,5, ,2,3,4,5, , ,6, ,6, ,2,6, ,6, ,3,6, ,3,6, ,2,3,6, ,6, ,4,6, ,4,6, ,2,4,6, ,4,6, ,3,4,6, ,3,4,6, ,2,3,4,6, ,6,8 Name Cod Dip switch ON 177 1,5,6, ,5,6, ,2,5,6, ,5,6, ,3,5,6, ,3,5,6, ,2,3,5,6, ,5,6, ,4,5,6, ,4,5,6, ,2,4,5,6, ,4,5,6, ,3,4,5,6, ,3,4,5,6, ,2,3,4,5,6, , ,7, ,7, ,2,7, ,7, ,3,7, ,3,7, ,2,3,7, ,7, ,4,7, ,4,7, ,2,4,7, ,4,7, ,3,4,7, ,3,4,7, ,2,3,4,7, ,7,8 Name Cod Dip switch ON 209 1,5,7, ,5,7, ,2,5,7, ,5,7, ,3,5,7, ,3,5,7, ,2,3,5,7, ,5,7, ,4,5,7, ,4,5,7, ,2,4,5,7, ,4,5,7, ,3,4,5,7, ,3,4,5,7, ,2,3,4,5,7, ,7, ,6,7, ,6,7, ,2,6,7, ,6,7, ,3,6,7, ,3,6,7, ,2,3,6,7, ,6,7, ,4,6,7, ,4,6,7, ,2,4,6,7, ,4,6,7, ,3,4,6,7, ,3,4,6,7, ,2,3,4,6,7,8 240* 5,6,7,8 Name *NOTE: code 240 is reserved for the porter switchboard EXAMPLE: dip switch setting for code 200 9

10 Special programming -V +V GND PR sec Set the dip switches for the function you wish to program, see Special programming table GND 7 PR 10

11 Special programming table CODE DIP SWITCH ON FUNCTIONS Audio-visal messages (Art. 1622L only) 210 2,5,7,8 visual messages only (Art. 1622L only) 211 1,2,5,7,8 Swedish (Art. 1622L only) 214 2,3,5,7,8 OFF (default) (Art. 1622L only) 215 1,2,3,5,7,8 Italian (Art. 1622L only) 216 4,5,7,8 French (Art. 1622L only) 217 1,4,5,7,8 Spanish (Art. 1622L only) 218 2,4,5,7,8 Dutch (Art. 1622L only) 219 1,2,4,5,7,8 Greek (Art. 1622L only) 220 3,4,5,7,8 English (Art. 1622L only) 221 1,3,4,5,7,8 German (Art. 1622L only) 222 2,3,4,5,7,8 Portuguese (Art. 1622L only) Door lock 223 1,2,3,4,5,7,8 Door lock command on SE in AC (default) 224 6,7,8 Door lock command on SE in enhanced AC 225 1,6,7,8 Door lock command on SE in DC 245 1,3,5,6,7,8 Door lock time: 2 sec + deactivation tone (default) 246 2,3,5,6,7,8 Door lock time: 4 sec 247 1,2,3,5,6,7,8 Door lock time: 8 sec 248 4,5,6,7,8 Door lock confirmation tone: enabled 251 1,2,4,5,6,7,8 C.NC.NO relay in parallel with SE (default) 252 3,4,5,6,7,8 Lock-release always enabled (default) 253 1,3,4,5,6,7,8 Lock-release only enabled for user called Actuator control management N.B. the system should not include Art in generic actuator mode ,3,6,7,8 Enabling C.NC.NO relay on actuator control: 2 sec 230 2,3,6,7,8 Enabling C.NC.NO relay on actuator control: 4 sec 231 1,2,3,6,7,8 Enabling C.NC.NO relay on actuator control: 8 sec 228 3,6,7,8 Actuator control on serial line S: disabled (default) 227 1,2,6,7,8 Actuator control on serial line S: enabled System functions 232 4,6,7,8 Awaiting response time: 60 sec (default) 233 1,4,6,7,8 Awaiting response time: 120 sec 234 2,4,6,7,8 Awaiting response time: 30 sec 235 1,2,4,6,7,8 Talk time: 90 sec (default) 236 3,4,6,7,8 Talk time: 180 sec 237 1,3,4,6,7,8 Self-ignition: enabled (default) 238 2,3,4,6,7,8 Self-ignition: disabled 239 1,2,3,4,6,7,8 Confirmation tone on user call: enabled (default) 240 5,6,7,8 Confirmation tone on user call: disabled 11

12 243 1,2,5,6,7,8 Reset wait time: 10 sec (default) 244 3,5,6,7,8 Reset wait time: 1 sec 208 5,7,8 Reset after lock-release in audio: enabled (default) 209 1,5,7,8 Reset after lock-release in audio: disabled 249 1,4,5,6,7,8 Call transmission: single (default) 250 2,4,5,6,7,8 Call transmission: triple 241 1,5,6,7,8 Gestione posti interni collegati all'art. 1622: fino a 70 (default) 242 2,5,6,7,8 Gestione posti interni collegati all'art. 1622: da 71 a 100 System mode 0 Simplebus (default) 255 1,2,3,4,5,6,7,8 Simplebus Top 254 2,3,4,5,6,7,8 Restore default 12

13 Operating distances with Art B 1622 A 1595 Operating distances A MAX 1 mm² (Ø 1,2 mm AWG 17) 50 m (165 feet) 0,28 mm² (Ø 0,6 mm AWG 23) 5 m (15 feet) 0,5 mm² (Ø 0,8 mm AWG 20) 25 m (85 feet) 1,5 mm² (Ø 1,4 mm AWG 15) 75 m (245 feet) 2,5 mm² (Ø 1,8 mm AWG 13) 100 m (330 feet) B MAX 500 m (1625 feet) 300 m (990 feet) 400 m (1315 feet) 600 m (1980 feet) 800 m (2600 feet) Maximum system expansion Max. number of door-entry phones that can be connected 100 Max. number of internal units with the same user code 3 Max. number of call repetition devices 1 13

14 Wiring diagrams Door-entry phone system with 1 audio port, Ikall series. Switching on/voltage check with system in standby V Vdc Local lock release button. SB/TNP 14

15 Door-entry phone system with 2 audio ports, Ikall series V V Local lock release button. SBC/014NP 15

16 Wiring diagram for system with digital call module Art V Local lock release button. SB/QNP Wiring diagram with safety lock V Local lock release button. SB2/SNP 16

17 Using the external unit relay on lock-release or actuator control V 230 V V/24V AC-DC 10A MAX S E C O M NC NO G N D P R D O R T E - V V + L L 1622 J1 J2 J1 J f f C.NC.NO relay activation on actuator command: 2 sec ff Set the dip switches permanently as shown in the figure (Dip switch ON 8, Dip switch OFF 1,2,3,4,5,6,7) Applies to Art. 1622L. Applies to Art with R.I. 038 or greater Local lock release button. SB/RTNP Door open indication use variant V Only for use in systems with a single external unit without switching devices Art. 1224A, Art N.C. contact for DOOR OPEN indication. The LED for the following internal units flashes: Art with R.I. 008, Art with R.I SB/DO 17

18 Protection device connection variant for line Art V Local lock release button. SB2V/SCA Use of RC network for lock filter on relay contacts Jumper On C. NO contacts. On C. NC contacts. Excluded: voltage-free contact 18

19 19

20 1 st edition 09/2016 cod. 2G Via Don Arrigoni, Rovetta (BG) - Italy