LTEC Unit Ventilator DDC Controller

Size: px
Start display at page:

Download "LTEC Unit Ventilator DDC Controller"

Transcription

1 Document No. 09 Rev., May, 00 LTEC Unit Ventilator DDC Controller Product Description These instructions explain how to install or replace a LTEC (LonMark Terminal Equipment Controller) UV (Unit Vent) DDC Controller (Figure ). Each platform supports various applications of the Unit Vent terminal unit. Each application set has a default input / output wiring configuration shown in Figure through Figure 9. The LTEC UV DDC Controller applications are provided in the following configurations: UVC Unit Vent Chill Water, w/single speed fan, or pipe heating and/or cooling coils, outside air damper control. UVD Unit Vent DX, w/single speed fan, single or multi stage DX cooling, terminal heating coils, outside air damper control. UVF Unit Vent Face & Bypass damper control, or pipe cooling and/or heating coils, outside air damper control. In addition to the listed inputs above, each platform can accept a series 080 through 08 LTEC room temperature sensor () with optional digital display, occupancy override push button and set point adjustment. Warning/Caution Notations WARNING CAUTION Personal injury/loss of life may occur if a procedure is not performed as specified. Equipment damage, or loss of data may occur if the user does not follow procedure as specified. /" " LON000R Figure. LTEC Controller open cover. 8 /8" 8 /" V V V AI/ DI AI/ DI AI/ DI AI/ DI AI/ DI J J J J J J A0 A0 A0 D0 Vac H D0 Vac H D0 Vac H D0 Vac H 8 D0 9 Vac H 0 D0 Vac H D0 Vac H D08 Vac H Vac H H Product Number Part number Application Input/Output 00 LTEC UVC CW/HW / pipe IN, DO 0 LTEC UVC CW/HW / pipe IN, 8 DO, AO 0 LTEC UVD DX w/htg. IN, DO 0 LTEC UVD DX w/htg. IN, 8 DO, AO 0 LTEC UVF w/face/bypass w / pipe htg/clg IN, 8 DO, AO LON00R /8" LO HI Figure. LTEC Controller. Siemens Building Technologies, Inc. Page of 0

2 Document No. 09 Rev., May, 00 Required Tools Pencil ESD wrist strap Small flat blade screwdriver Medium flat blade screwdriver Wire stripper Medium duty electric drill ¼ in (mm) hex nut bit Network Management Tool Bus interface and cables Prerequisites Room temperature sensor (), if required, is installed Power source of Vac, 0 Hz Class power trunk is available and has a sufficient VA rating for the controller, sensors and actuators If required, the controller enclosure is installed Power supply to the unit is OFF Installation WARNING: The power must be turned OFF prior to wiring the unit. The following sections are included in these instructions: Controller Mounting Power Wiring Bus Wiring Replacing a Controller Controller Mounting. Using the controller as a template, position the controller vertically and mark the mounting hole locations on the mounting surface (terminal box or mounting enclosure).. Using the # selftapping screws (included), fasten the controller to the terminal box or enclosure.. Connect the Network Trunk (NOT polarity sensitive) cable to terminals and on J, (Figure ). Network Management Tool Connection Room Temperature Sensor Connection Service Pin LON00R Network Trunk Analog or Digital Input V AI/ DI V AI/ DI AI/ DI AI/ DI V AI/ DI J J J able on reduced point controller boards. Only available on Unit Vent Controller. J J J Cover Release Tabs A0 A0 A0 D0 Vac H D0 Vac H D0 Vac H D0 Vac H 8 D0 9 Vac H 0 D0 Vac H D0 Vac H D08 Vac H Vac H H Figure. LTEC Wiring Designations. Mounting Holes () Analog Output Digital Output Vac Power. With primary power disconnected, connect vac power to terminal block J.. Connect the EGrnd terminal (E) to an earth ground. A proper ground source is required to protect the electronic circuits, for example; a cold water pipe, power panel ground (green wire) or other comparable ground sources.. Connect the input and output wiring for the appropriate UV (Unit Vent) application. Refer to the Terminal Designations section for complete information on LTEC wiring designations for 0 0 through 0 controllers. Page of 0 Siemens Building Technologies, Inc.

3 Document No. 09 Rev., May, 00. For input type selection, (digital, voltage, or current) see the jumper and connection information in Table. Each DO provides a normally open (NO) and Vac hot (H) terminal. Terminate both connections of a Vac load directly to the controller board. Floating control actuators require DOs and use wire connections. The Vac Common is switched through the Triac when the associated DO is energized. CAUTION: The controllers Digital Outputs (DOs) control Vac only. The maximum rating is VA for each DO. Use an interposing Vac relay for any of the following: VA requirements higher than the maximum 0 or 0 Vac or higher Control load requires DC power Separate transformers used to power the load Need for dry contacts 8. Plug the room temperature sensor () cable into the port on the left side of the controller. See Figure. 9. Remove one of the controller neuron ID labels (two part label located at the top of the controller board). Record this number as directed in a floor plan layout, job log or place the selfadhesive label on the outside of the controller case or inside the cover. This number is unique to the controller electronics. Installation is complete. Power Wiring Each Controller requires a source of Vac, 0 Hz Class II power supply. The base rating of the controller and the sum of the sensor, actuators and relays connected dictates the VA rating. Bus Trunk wiring Bus wiring must be accomplished using approved cables only. These include unshielded and shielded (where specified) two conductor AWG Level IV cable. WARNING: Use the recommended LonWorks cable: AWG shielded or unshielded, Level IV per NEMA standards (not equivalent to EIA/TIA Level cable). Connect Air brand cable, / pair, stranded, unshielded, blue plenum jacketed, Level IV, Part Number WP00 or an approved equal for bus wiring. Bus wiring is NOT polarity sensitive. The LTEC Controllers use the FTT0 transceiver that allows free topology wiring. This includes Ttaps, stars, branches, loops as well as standard daisy chain. In all cases, max bus wire length, including each sensor cable, cannot exceed 00 meters (0 feet). For bus lengths that exceed 00 meters, (0 feet) a twoport or threeport repeater can be used (Part number 80 and 8 respectively). This will allow three separate bus lengths of 00 meters. See the LonTalk Two and Three Port Repeater installation instructions, (P/N: 00) for additional information and limitations. Each bus segment ( without repeater, with repeater) requires a pair of terminating resistors (Part number 8 9 packs of 00) that can be located together anywhere on the segment, at the field panel or repeater. The installation is now complete. Siemens Building Technologies, Inc. Page of 0

4 Document No. 09 Rev., May, 00 Terminal Designations Figure shows the LTEC wiring designations and locations for both controllers. AI/DI AI/DI V V J All inputs and outputs physical connections are preconfigured per application number selected. The wiring diagrams (Figure thru Figure 9) are shown using the full point controllers (shaded terminals). Reduced point controllers should be used when the additional input/output points are not required. AI/DI AI/DI AI/DI LON008R V J J J Figure. Terminal Designations. Input Ports LTECs have configurable, flexible input ports. Table lists each input port and indicates the input options available for that port. Some models have only the first four inputs, while others have five inputs. (Only VAV models have the integral flow sensor port). Table. LTEC Input Port Configuration Options. Input type/number Configurable options Notes RJ input jack Temperature sensor 080 thru 8 wall modules Set point adjustment Override button AI/DI Digital Input 00K thermistor Temperature Input AI/DI Digital Input 00K thermistor Temperature Input AI/DI Digital Input Percent Input Temperature transmitter 00Vdc or 00/0 ma AI/DI AI/DI Digital Input Percent Input Temperature transmitter Digital Input Percent Input Temperature transmitter 00Vdc or 00/0 ma 00Vdc or 00/0 ma Integral Flow Sensor N/a VAV/CV only Page of 0 Siemens Building Technologies, Inc.

5 Document No. 09 Rev., May, 00 Table. Input Configuration and Jumper Settings. Digital Input 00 K thermistor 00 Vdc input 00/ 0 ma input AI/DI J J LON0009R LON00R T AI/DI J J LON00R LON00R T AI/DI LON009R J LON00R J LON00R 00Vdc J LON000R J LON00R 0mA J J LON009R AI/DI LON000R J J LON00R LON00R 00 Vdc J J LON00R LON008R 0mA J J LON00R AI/DI J J J LON00R LON000R 00 Vdc LON00R 00 ma (0 ma). Resistor, 99 Ω %, part number (8) for AI current input (00 ma).. See Figure for physical location of s and external terminal block connections.. The location of physical inputs must match a specific application wiring diagram; see Figure through Figure 9. Output Ports LTECs have configurable, flexible output ports. Wiring diagrams (Figure through Figure 9) indicate how these outputs are used in each application. Each application has preassigned output configurations. Some models have only the first six Digital outputs and no Analog outputs, while other have all eight Digital outputs and three Analog outputs. Replacing a Controller Replacement of a LTEC requires you to record, reenter, and/or update the initial point values from the old controller before replacing it. LTEC Network Connections (data sharing between controllers; Connections tab in Network Management Tool) () do not need to be recorded if using s Replace feature. will reapply the Connections after the Replace. However, if the old controller is to be deleted in, then all connections will need to be recorded first so they can be reentered after the new controller is added. Siemens Building Technologies, Inc. Page of 0

6 Document No. 09 Rev., May, 00. To record Initial Values, before disconnecting the old controller, do one of the following: If the controller is communicating with the field panel, update the controller initial values at the field panel. If the controller does not communicate with the field panel, but does communicate with the, record the appropriate configuration points on Table at the end of these instructions. If the old controller is not communicating at all, record all data available in the Point Definition Report, or from the last valid initial values uploaded from the controller.. Disconnect power to the controller (remove the power connector, terminal block J).. Disconnect all input and output removable terminal blocks and insure they do not short out.. Remove the and network (RJ) connectors.. Remove the controller board by pressing the internal tabs and lifting the board out (or the complete controller, by removing the mounting screws).. Install the new controller board (or base and board).. Install jumpers. Ensure jumpers for AI/DI and AI/DI are configured to match the removed controller, see Table. Ensure AI/DI, AI/DI and AI/DI, external jumpers, remain in place or are reinstalled. 8. Remove one of the Neuron ID labels (two part label located at the top of the controller board). Record this number as directed; on a floor plan layout, job log or inside the cover.. Reconnect power to controller, terminal block J.. Connect to the LTEC or L model MEC.. Run and use Replace to replace the old controller with new one. If the replacement controller was previously used elsewhere (not in factory packaging) the factory defaults must be reestablished as follows: Using, select the controller, select Application Configuration and apply the Set to Defaults command.. Apply the appropriate Configuration Template.. Restore initial values as follows: MMI: If a field panel update was performed, the LTECs initial values will be loaded automatically. : If a field panel update was NOT performed, set the initial values previously recorded in Table.. : Verify LTEC Connections are correct, update as needed.. Save the peak database (.pkd file) to flash/file as needed. Replacement installation is complete. Disposal As an aid to environmentally responsible disposal, the larger plastic components bear a recycle symbol. The controller should not be disposed of with domestic waste. The printed circuit board and plastic components should be disposed of separately in accordance with local regulations. This number is unique to the controller electronics. It is imperative that the old neuron label be removed or covered. 9. Reconnect input and output terminal blocks. 0. Reconnect and network (RJ) connectors. Page of 0 Siemens Building Technologies, Inc.

7 Document No. 09 Rev., May, 00 LTEC UV Application Wiring Diagrams Room Sensor Network Trunk *Discharge Temp Sensor Spare Temp Sensor Fan Status DI *Low Temp Sensor DI OA Temp Transmitter 00 Vdc/0 ma V V V AI/ DI AI/ DI AI/ DI AI/ DI AI/ DI J J J J J A0 A0 A0 D0 Vac H D0 Vac H D0 Vac H D0 Vac H 8 D0 9 Vac H 0 D0 Vac H D0 Vac H D08 Vac H OA Damper Act. 00 Vdc Terminal Clg. Coil 00 Vdc Terminal Htg. Coil 00 Vdc Terminal Fan Relay OA Damper Act. Terminal Clg. Coil Terminal Htg. Coil Perimeter Htg. DO J Vac H H Ground Vac Power LON808WDR able on reduced point controller boards. *Required Sensor Figure. Application 808 UVCW pipe Cooling/Heating (00 or 0). Room Sensor Network Trunk *Discharge Temp Sensor Spare Temp Sensor Fan Status DI *Low Temp Sensor DI OA Temp Transmitter 00 Vdc/0 ma V V V AI/ DI AI/ DI AI/ DI J AI/ DI J AI/ DI J J J A0 A0 A0 D0 Vac H D0 Vac H D0 Vac H D0 Vac H 8 D0 9 Vac H 0 D0 Vac H D0 Vac H D08 Vac H OA Damper Act. 00 Vdc Perimeter Htg. Coil 00 Vdc Terminal Htg. Coil 00 Vdc DX Stage Clg. Terminal Fan Relay Terminal Htg. Coil OA Damper Act. Perimeter Htg. Coil J Vac H H Vac Power Ground LON808WDR able on reduced point controller boards. *Required Sensor Figure. Application 808 UVDX with Hot Water Heat (0 or 0). Siemens Building Technologies, Inc. Page of 0

8 Document No. 09 Rev., May, 00 Room Sensor Network Trunk *Discharge Temp Sensor Spare Temp Sensor Fan Status DI *Low Temp Sensor DI OA Temp Transmitter 00 Vdc/0 ma V V V AI/ DI AI/ DI AI/ DI J AI/ DI J AI/ DI J J J A0 A0 A0 D0 Vac H D0 Vac H D0 Vac H D0 Vac H 8 D0 9 Vac H 0 D0 Vac H D0 Vac H D08 Vac H OA Damper Act. 00 Vdc Perimeter Htg. Coil 00 Vdc Spare AO Terminal Fan Relay DX Staged Clg. Terminal Staged Heat OA Damper Act. J Vac H H Vac Power Ground LON808WDR able on reduced point controller boards. *Required Sensor Figure. Application 808 UVDX stage and Electric Heat (0 or 0). Room Sensor Network Trunk *Discharge Temp Sensor Spare Temp Sensor Fan Status DI *Low Temp Sensor DI OA Temp Transmitter 00 Vdc/0 ma V V V AI/ DI AI/ DI AI/ DI J AI/ DI J AI/ DI J J J A0 A0 A0 D0 Vac H D0 Vac H D0 Vac H D0 Vac H 8 D0 9 Vac H 0 D0 Vac H D0 Vac H D08 Vac H OA Damper Act. 00 Vdc Perimeter Htg. Coil 00 Vdc Terminal Clg. / Htg. Coil 00Vdc Terminal Fan Relay OA Damper Act. Terminal Clg. / Htg. Coil Spare DO Perimeter Htg. Coil J Vac H H Vac Power Ground LON8088WDR able on reduced point controller boards. *Required Sensor Figure 8. Application 8088 UVCW pipe Cooling/Heating (00 or 0). Page 8 of 0 Siemens Building Technologies, Inc.

9 Document No. 09 Rev., May, 00 Room Sensor Network Trunk *Discharge Temp Sensor Spare Temp Sensor Fan Status DI *Low Temp Sensor DI OA Temp Transmitter 00 Vdc/0 ma V V V AI/ DI AI/ DI AI/ DI J AI/ DI J AI/ DI J J J A0 A0 A0 D0 Vac H D0 Vac H D0 Vac H D0 Vac H 8 D0 9 Vac H 0 D0 Vac H D0 Vac H D08 Vac H OA Damper Act. 00 Vdc Perimeter Htg. Coil 00 Vdc F&B Damper Act. 00 Vdc Terminal Fan Relay OA Damper Act. F&B Damper Act. Terminal Htg. DO Terminal Clg. DO Spare DO J Vac H H Vac Power Ground LON8089WDR *Required Sensor Figure 9. Application 8089 UV pipe Face/Bypass, Cooling/Heating. (0) Siemens Building Technologies, Inc. Page 9 of 0

10 Document No. 09 Rev., May, 00 Table. Record of Controller Modified Initial Values. Point Number Descriptor Initial Value Point Number Descriptor Initial Value Information in this publication is based on current specifications. The company reserves the right to make changes in specifications and models as design improvements are introduced. 00 Siemens Building Technologies, Inc. Siemens Building Technologies, Inc. Landis and Staefa Division 000 Deerfield Parkway Buffalo Grove, IL 0089 U.S.A. Your feedback is important to us. If you have comments about this document, please send them to Document No. 09 Printed in the U.S.A. Page 0 of 0

LTEC Heat Pump DDC Controller

LTEC Heat Pump DDC Controller Document No. 09 Rev., May, 00 LTEC Heat Pump DDC Controller Product Description These instructions explain how to install or replace a LTEC (LonMark Terminal Equipment Controller) HP (Heat Pump) DDC Controller

More information

TEC Unit Conditioner Controller

TEC Unit Conditioner Controller Document No. 540-1026 TEC Unit Conditioner Controller Generic Controller I/O Layout. See Wiring Diagram for application specific details. Control Applications 2040 and 2041 2050 through 2054 Product Description

More information

BACnet PTEC Unit Conditioner/Fan Coil P. Controller. Control Applications. Accessories. Product Description. Warning/Caution Notation

BACnet PTEC Unit Conditioner/Fan Coil P. Controller. Control Applications. Accessories. Product Description. Warning/Caution Notation Installation Instructions BACnet PTEC Unit Conditioner/Fan Coil Controller Figure 1. BACnet PTEC Unit Conditioner/Fan Coil Controller. Control Applications 6540, 6541, 6550, 6551, 6552, 6553 and 6554 Product

More information

TEC Terminal Box (VAV) Controller

TEC Terminal Box (VAV) Controller Document No. 540-1025 TEC Terminal Box (VAV) Controller Generic Controller I/O Layout. See Wiring Diagram for application specific details. Control Applications 2020 through 2027 Product Description These

More information

BACnet PTEC Terminal Box (VAV) Controller. Control Applications. Product Numbers. Product Description. Warning/Caution Notation

BACnet PTEC Terminal Box (VAV) Controller. Control Applications. Product Numbers. Product Description. Warning/Caution Notation BACnet PTEC Terminal Box (VAV) Controller Generic Controller I/O Layout. See Wiring Diagram for application specific details. Control Applications 6600 through 6607 Product Description These instructions

More information

TEC VAV with 0-10V AO Heat. Modulation and CO2 Monitoring. Controller. Control Applications. Product Description. Accessories.

TEC VAV with 0-10V AO Heat. Modulation and CO2 Monitoring. Controller. Control Applications. Product Description. Accessories. Document No. 540-1031 TEC VAV with 0-10V AO Heat Modulation and CO2 Monitoring Controller Generic Controller I/O Layout. See Wiring Diagram for application specific details. Control Applications 2843,

More information

BACnet PTEC Heat Pump Multi-Stage Controller. Control Applications. Product Description. Product Numbers. Warning/Caution Notation

BACnet PTEC Heat Pump Multi-Stage Controller. Control Applications. Product Description. Product Numbers. Warning/Caution Notation BACnet PTEC Heat Pump Multi-Stage Controller Generic Controller I/O Layout. See Wiring Diagram for application specific details. Control Applications 6673, 6674 Product Description These instructions explain

More information

Room Pressurization Controller Electronic Output

Room Pressurization Controller Electronic Output Document No. 540-1033 Room Pressurization Controller Electronic Output Product Description These instructions explain how to field install or replace a Room Pressurization Controller (RPC) Electronic Output

More information

Room Pressurization Controller Pneumatic Output

Room Pressurization Controller Pneumatic Output Document No. 540-1032 Room Pressurization Controller Pneumatic Output Product Description These instructions explain how to field install (pages 1 through 3) or replace (pages 3 through 4) a Room Pressurization

More information

TEC Heat Pump Multi-Stage Controller. Control Applications. Accessories. Product Description. Product Numbers. Warning/Caution Notation

TEC Heat Pump Multi-Stage Controller. Control Applications. Accessories. Product Description. Product Numbers. Warning/Caution Notation Document No. 540-1024 TEC Heat Pump Multi-Stage Controller Generic Controller I/O Layout. See Wiring Diagram for application specific details. Control Applications 2273 and 2274 Product Description These

More information

Siemens TEC Extended I/O Controller

Siemens TEC Extended I/O Controller Document No. 540-1028 TEC Extended I/O Controller Generic Controller I/O Layout. See Wiring Diagram for application specific details. Control Applications 2497 Product Description These instructions explain

More information

DESIGO RX Individual room controllers. for fan-coil systems, chilled ceilings and radiators, with LONMARK-compatible bus communications

DESIGO RX Individual room controllers. for fan-coil systems, chilled ceilings and radiators, with LONMARK-compatible bus communications 3 834 DESIO RX Individual room controllers for fan-coil systems, chilled ceilings and radiators, with MARK-compatible bus communications RXC20.1 RXC21.1 The RXC20.1 and RXC21.1 controllers are used for

More information

SLX Series. Application Specific Controllers (SLX-ASC-FCU-L, SLX-ASC-HPU-L, SLX-ASC-RTU-L, SLX-ASC-UV-L)

SLX Series. Application Specific Controllers (SLX-ASC-FCU-L, SLX-ASC-HPU-L, SLX-ASC-RTU-L, SLX-ASC-UV-L) SLX Series Document No. 997-1000 Application Specific Controllers (SLX-ASC-FCU-L, SLX-ASC-HPU-L, SLX-ASC-RTU-L, SLX-ASC-UV-L) Free Programmable Controllers (SLX-PC-203, SLX-PC-300, SLX-PC-400, SLX-PC-500

More information

TRUNK TX RX + - S + - S DO LEDS FLN TRUNK TERMINATIONS INPUT/OUTPUT TERMINATIONS TRANSMIT LED

TRUNK TX RX + - S + - S DO LEDS FLN TRUNK TERMINATIONS INPUT/OUTPUT TERMINATIONS TRANSMIT LED Heat Pump Controller Single Stage COVR CONTROLLR BOARD MOUNTING HOL (2) C H DO 1 DO 2 DO 3 DO 4 DO 5 DO 6 DI 3 DI 2 FLN TX RX + - S BST RTS MOUNTING RAIL + - S TC0168R5 POWR TRMINATIONS DO LDS FLN TRMINATIONS

More information

UNT1100 Series. Binary Output Jumpers AO2 AO1 AO3 AO4 AOCM AOCM AOCM AOCM AO1. AI Switches Job Information N2 Address. Ref N2+ N2- ADDR 0 = ALL OPEN

UNT1100 Series. Binary Output Jumpers AO2 AO1 AO3 AO4 AOCM AOCM AOCM AOCM AO1. AI Switches Job Information N2 Address. Ref N2+ N2- ADDR 0 = ALL OPEN 1 2 8 4 AI6 R R Installation Bulletin UNT1100 Issue Date 0309 UNT1100 Series Introduction The Unitary (UNT) controller (UNT1100 Series) is a digital controller with applications for air handling units,

More information

Free Energy Band RCC30U Room Temperature Controller for Four-pipe Fan Coil Unit

Free Energy Band RCC30U Room Temperature Controller for Four-pipe Fan Coil Unit Document No. 155-324 Free Energy Band RCC30U Room Temperature Controller for Four-pipe Fan Coil Unit Description Features Application Product Number Room temperature controller for four-pipe fan coil units.

More information

Open Processor with Square D Driver

Open Processor with Square D Driver Document No. 565-922 Open Processor with Square D Driver PRODUCT DESCRIPTION Each Open Processor (Figure 1) contains the main processor, memory, and communications circuitry for connecting APOGEE to another

More information

RWD68U Universal Controller

RWD68U Universal Controller Document No. 155-738 RWD68U Universal Controller Description Features Product Number The Universal Controller is intended for heating, air conditioning, ventilation and refrigeration in comfort control

More information

Siemens BACnet Programmable TEC Unit Vent Controller for Smoke Control

Siemens BACnet Programmable TEC Unit Vent Controller for Smoke Control Technical Specification Sheet Document No. 149-841 August 12, 2011 Siemens BACnet Programmable TEC Unit Vent Controller for Smoke Control The Siemens BACnet PTEC Unit Vent Controller provides high performance

More information

Siemens BACnet Programmable TEC Unit Vent Controller

Siemens BACnet Programmable TEC Unit Vent Controller Technical Specification Sheet Document No. 149-833 August 12, 2011 Siemens BACnet Programmable TEC Unit Vent Controller The Siemens BACnet PTEC Unit Vent Controller provides high performance Direct Digital

More information

TEC Controller Extended I/O Application 2497 with Slave Mode Application Application Note Building Technologies

TEC Controller Extended I/O Application 2497 with Slave Mode Application Application Note Building Technologies TEC Controller Extended I/O Application 2497 with Slave Mode Application 2489 Application Note 140-1074 Building Technologies Table of Contents Overview... 4 Hardware Inputs... 4 Hardware Outputs... 4

More information

Terminal Equipment Controller Enclosure

Terminal Equipment Controller Enclosure Document No. 550-196 Terminal Equipment Controller Enclosure Product Description A Terminal Equipment Controller enclosure is a general-purpose metal cabinet with a removable cover that houses an electronic

More information

Installation and Operation. Tracer MP501 Controller CNT-SVX08B-EN

Installation and Operation. Tracer MP501 Controller CNT-SVX08B-EN Installation and Operation Tracer MP501 Controller CNT-SVX08B-EN Installation and Operation Tracer MP501 Controller CNT-SVX08B-EN April 2005 CNT-SVX08B-EN Tracer MP501 Controller Installation and Operation

More information

PXC Compact Unitary Equipment Controller (UEC)

PXC Compact Unitary Equipment Controller (UEC) Document No. 553-169 PXC Compact Unitary Equipment Controller (UEC) Product Description The PXC Unitary Equipment Controller (UEC) is an MS/TP device that can be configured as a programmable, stand-alone

More information

Siemens BACnet Programmable TEC Unit Conditioner (Fan Coil) Controller for Smoke Control

Siemens BACnet Programmable TEC Unit Conditioner (Fan Coil) Controller for Smoke Control Technical Specification Sheet Document No. 149-844 August 12, 2011 Siemens BACnet Programmable TEC Unit Conditioner (Fan Coil) Controller for Smoke Control Returns from power failure without operator intervention.

More information

Hardware Installation. Tracer MP581 Programmable Controller CNT-SVN01C-EN

Hardware Installation. Tracer MP581 Programmable Controller CNT-SVN01C-EN Hardware Installation Tracer MP581 Programmable Controller CNT-SVN01C-EN Hardware Installation Tracer MP581 Programmable Controller CNT-SVN01C-EN November 2005 Tracer MP581 Programmable Controller Hardware

More information

Junos WebApp Secure 5.0 Hardware Guide

Junos WebApp Secure 5.0 Hardware Guide Junos WebApp Secure 5.0 Hardware Guide Junos WebApp Secure 5.0 Hardware Guide This document contains a specification for the MWS1000 hardware appliance, as well as instructions for installation into a

More information

Content. Product Description

Content. Product Description EY-modulo 4 EY-RU482F001 Room Operating Unit with Display for Fan Coil applications EY-RU483F001 Room Operating Unit with Display for VAV applications en Guidelines for the electrician Content 1 Product

More information

TECH/DATA SHEET. Application. Model Chart. Installation. slon-v1. slon-v2. slon VAV Controller

TECH/DATA SHEET. Application. Model Chart. Installation. slon-v1. slon-v2. slon VAV Controller TECH/DATA SHEET s-v1 s-v2 s VAV Controller Application Solidyne s s-v1 and s-v2 VAV Controllers are interoperable MARK -compliant variable air volume controllers. These controllers provide pressure independent

More information

Replacing the Power Supply

Replacing the Power Supply APPENDIX B This appendix includes information on how to replace the power supply for the Cisco AS550XM universal gateway and contains the following sections: Safety Recommendations, page B-1 Required Tools

More information

Non-communicating room controllers

Non-communicating room controllers 3 882 DESIGO RXA Non-communicating room controllers RXA29.1 For fan-coil systems The RXA29.1 room controller are used for temperature control in individual rooms. For 2-pipe or 4-pipe fan-coil systems,

More information

RXC39.5. Room controller. Building Technologies. Desigo RXC. Communicating room controller for fan-coil applications

RXC39.5. Room controller. Building Technologies. Desigo RXC. Communicating room controller for fan-coil applications s 3 856 Desigo RXC Room controller RXC39.5 Communicating room controller for fan-coil applications The RXC39.5 room controller is used for temperature control in individual rooms. For fan-coil systems

More information

DS A 10/99 MN 500 I/A SERIES MICRONET MN 500 CONTROLLERS APPLICATION SPECIFICATION

DS A 10/99 MN 500 I/A SERIES MICRONET MN 500 CONTROLLERS APPLICATION SPECIFICATION DS 10.103A 10/99 MN 500 WIRING AND COMMISSIONING INFORMATION FOR I/A SERIES MICRONET MN 500 CONTROLLERS APPLICATION Order Type: MNN-50-100 MicroNet NCP 500 Controller I/A Series MicroNet 500 Series Controllers

More information

Actuator Commissioning Tool

Actuator Commissioning Tool Document No. 129-287 Actuator Commissioning Tool Product Description The 985-047 Actuator Commissioning Tool provides a portable instrument for exercising, calibrating, and testing resistive, proportional

More information

ETM-2050/ETM-2051 Service Manual

ETM-2050/ETM-2051 Service Manual Introduction Novar s Electronic Thermostat Modules (ETMs) are intelligent control modules that provide local, direct digital control of unitary, packaged, staged HVAC systems. This document: Describes

More information

Non-communicating room controllers

Non-communicating room controllers 3 881 DESIO RXA on-communicating room controllers For fan-coil systems RXA20.1 RXA21.1 RXA22.1 The RXA20.1, RXA21.1 and RXA22.1 room controllers are used for temperature control in individual rooms. For

More information

Siemens BACnet Programmable TEC Unit Conditioner Controller

Siemens BACnet Programmable TEC Unit Conditioner Controller Technical Specification Sheet Document No. 149-831 September 24, 2014 Siemens BACnet Programmable TEC Unit Conditioner Controller Returns from power failure without operator intervention. No calibration

More information

NEUROLOGIC RESEARCH CORPORATION MODEL 2500

NEUROLOGIC RESEARCH CORPORATION MODEL 2500 NEUROLOGIC RESEARCH CORPORATION MODEL 2500 NETWORK HUMISTAT Compact, self-contained dehumidifier controller. 0.5 degrees C accuracy typical. RH sensor is digitally calibrated for 2% accuracy. Open communication

More information

Suitable for a wide range of installations with wall-mount, flush-mount and hand-held remote control options.

Suitable for a wide range of installations with wall-mount, flush-mount and hand-held remote control options. TUC03 Configurable Terminal Unit Controller Product Bulletin The TUC03 Configurable Terminal Unit Controller is designed specifically to provide direct digital control of terminal unit applications with

More information

ENCL-MZ800-WAL ENCL-MX800-PAN MNL TAC I/A Series MicroNet MN 800 Series Controller Installation Instructions. Application.

ENCL-MZ800-WAL ENCL-MX800-PAN MNL TAC I/A Series MicroNet MN 800 Series Controller Installation Instructions. Application. TAC 1354 Clifford Avenue P. O. Box 2940 Loves Park, IL 61132-2940 www.tac.com ENCL-MZ800-WAL ENCL-MX800-PAN MNL-800-101 TAC I/A Series MicroNet MN 800 Series Controller Installation Instructions Application

More information

RTD-W Installation Instructions

RTD-W Installation Instructions RTD-W Installation Instructions 0V +V POWER 15-24VDC 0V S1 S2 S3 0V S4 S5 S6 English RTD-W Installation Instructions 100.00 RTD-W Control Interface realtime Control Systems 24VAC/30VDC, 1A REMC P1 P2 RS485

More information

TX-I/O Product Range. Description. Technical Specification Sheet Document No February 20, 2018

TX-I/O Product Range. Description. Technical Specification Sheet Document No February 20, 2018 Technical Specification Sheet Document No. 149-476 February 20, 2018 TX-I/O Product Range TX-I/O is a range of I/O modules, with associated power and communication modules, for use within the APOGEE Automation

More information

CTR21, CTR22, CTR23, and CTR24 Wall Modules

CTR21, CTR22, CTR23, and CTR24 Wall Modules CTR21, CTR22, CTR23, and CTR24 Wall Modules FEATURES SPECIFICATION DATA The CTR21, CTR22, CTR23, and CTR24 family of wall modules include: Models with setpoint adjustment. Models with occupied/unoccupied

More information

Siemens BACnet Programmable TEC Unit Conditioner (Fan Coil) Controller

Siemens BACnet Programmable TEC Unit Conditioner (Fan Coil) Controller Technical Specification Sheet Document No. 149-831 August 12, 2011 Siemens BACnet Programmable TEC Unit Conditioner (Fan Coil) Controller No calibration required, thereby reducing maintenance costs. PID

More information

TX-I/O Product Range. Description. Technical Specification Sheet Document No July 18, 2013

TX-I/O Product Range. Description. Technical Specification Sheet Document No July 18, 2013 Technical Specification Sheet Document No. 149-476 July 18, 2013 TX-I/O Product Range TX-I/O is a range of I/O modules, with associated power and communication modules, for use within the APOGEE Automation

More information

BA/BS4S Temperature Sensor Installation & Operating Instructions

BA/BS4S Temperature Sensor Installation & Operating Instructions Product Overview and Identification The BAPI-Stat 4 room temperature sensor features a large format LCD and slider setpoint adjustment. Additional options include button override and communication jack.

More information

Siemens BACnet VAV Actuator

Siemens BACnet VAV Actuator Technical Specification Sheet Document No. 149-481 May 30, 2012 Siemens BACnet VAV Actuator Setpoints and control parameters assigned and changed locally or remotely. Setpoints and control parameters stored

More information

Installing the Tracer MP503 Input/Output Module Ordering number: ,

Installing the Tracer MP503 Input/Output Module Ordering number: , Installing the Tracer MP503 Input/Output Module Ordering number: 4950 0490, 4950 0590 Product overview The Tracer MP503 input/output (I/O) module is a field-installed device used to monitor inputs and

More information

MAKING MODERN LIVING POSSIBLE AK-255 CO 2. Controller On-Site Installation Guide DANFOSS ELECTRONIC CONTROLS & SENSORS

MAKING MODERN LIVING POSSIBLE AK-255 CO 2. Controller On-Site Installation Guide DANFOSS ELECTRONIC CONTROLS & SENSORS MAKING MODERN LIVING POSSIBLE Controller On-Site Installation Guide DANFOSS ELECTRONIC CONTROLS & SENSORS How to Use This Guide Read this Guide completely as you install and start up your new Controller.

More information

OpenAir Electronic Damper Actuator GDE/GLB Rotary Non-spring Return

OpenAir Electronic Damper Actuator GDE/GLB Rotary Non-spring Return OpenAir Electronic Damper Actuator GDE/GLB Rotary Non-spring Return Document No. 9-67 EA678R a b e d c f a. Actuator b. Position indicator c. Mounting bracket d. Mounting screws e. 4 mm hex key f. Shaft

More information

MX1 Reversible AC Motor Controller. Supplementary Wiring Examples

MX1 Reversible AC Motor Controller. Supplementary Wiring Examples MX1 Reversible AC Motor Controller Supplementary Wiring Examples DANGER Electrocution Hazard! Ensure all power is disconnected before servicing or wiring. Install all electrical equipment and wiring in

More information

Installation & Operation Guide

Installation & Operation Guide Installation & Operation Guide (Shown with optional Override Board Cover) KMD-5831 Programmable Loop Controller PLC-28 Direct Digital Controller 902-019-04B 1 Introduction This section provides a brief

More information

Spyder Lon Programmable, VAV/Unitary Controllers

Spyder Lon Programmable, VAV/Unitary Controllers Spyder Lon Programmable, VAV/Unitary Controllers Controller Model Programmable Type Universal Inputs (UI) Table. Controller configurations. Digital Inputs (DI) PRODUCT DESCRIPTION PRODUCT DATA The PUL0S,

More information

Field selectable application type and room module series, via dip-switches on controller

Field selectable application type and room module series, via dip-switches on controller TUC03 Plus Configurable Terminal Unit Controller Product bulletin The TUC03 Plus configurable Terminal Unit Controller is specifically designed to provide an improved BACnet integration. It allows the

More information

Sylk I/O Devices APPLICATION FEATURES PRODUCT DATA

Sylk I/O Devices APPLICATION FEATURES PRODUCT DATA Sylk I/O Devices APPLICATION PRODUCT DATA The Sylk IO devices are part of the Spyder family. The three IO devices are designed to seamlessly integrate with Spyder with relay controllers using only Sylk

More information

FX-2 Control Board ASY-360-XXX Setup and Configuration Guide

FX-2 Control Board ASY-360-XXX Setup and Configuration Guide FX-2 Control Board ASY-360-XXX Setup and Configuration Guide Micro Air Corporation Phone (609) 259-2636 124 Route 526. WWW.Microair.net Allentown NJ 08501 Fax (609) 259-6601 Table of Contents Introduction...

More information

TAC Xenta 101-VF. 3-Speed Fan Coil Controller. TAC Xenta

TAC Xenta 101-VF. 3-Speed Fan Coil Controller. TAC Xenta TAC Xenta TAC Xenta 101-VF 3-Speed Fan Coil Controller TAC Xenta 101-VF is a zone controller intended primarily for fan coil applications with the ability to control fans with multiple speeds, with one

More information

Actuating Terminal Equipment Controller (ATEC) VAV with Reheat - Cooling and Heating, Application Application Note

Actuating Terminal Equipment Controller (ATEC) VAV with Reheat - Cooling and Heating, Application Application Note Actuating Terminal Equipment Controller (ATEC) VAV with Reheat - Cooling and Heating, Application 2501 Application Note 140-1220 Building Technologies Table of Contents Overview... 4 Hardware Inputs...

More information

T7560A1036 Digital Wall Module

T7560A1036 Digital Wall Module T7560A1036 Digital Wall Module HONEYWELL EXCEL 5000 OPEN SYSTEM BEFORE INSTALLATION All wiring must comply with local electrical codes and ordinances or as specified on installation wiring diagrams. T7560A1036

More information

Temperature controller Ducted systems

Temperature controller Ducted systems 2 725 Temperature controller Ducted systems Standard model without zoning functions RRV851 Multifunctional controller used for central control of ducted HVAC systems in combination with a QAX850 master

More information

TAC Xenta 121-FC Programmable Fan Coil Application

TAC Xenta 121-FC Programmable Fan Coil Application TAC Vista TAC Xenta 121-FC Programmable Fan Coil Application TAC Xenta 121-FC is an easily programmable controller intended for both 2-pipe and 4-pipe applications, with or without re-heat. It can be configured

More information

PROLON INSTALLATION AND START UP GUIDE

PROLON INSTALLATION AND START UP GUIDE PROLON INSTALLATION AND START UP GUIDE Part 1: Project preparation & cabling Figure 1. System disposition and cabling 1- Using a floor plan, determine the system s zone controller locations as well as

More information

RTD-NET Installation Instructions

RTD-NET Installation Instructions LED3 SW1 LED4 RTD-NET Installation Instructions 0V +V POWER 15-24VDC English RTD-NET Installation Instructions 100.00 RTD-NET Control Interface realtime Control Systems REMC P1 P2 RS485 D-BUS DB DA GND

More information

Hardware Installation Guide

Hardware Installation Guide Hardware Installation Guide IO Extension Module for ECL600 and ECB600 Series Controllers: 1. Product Description This document describes the hardware installation procedures for the I/O Extension Modules.

More information

Unit Vent Controller 0-10 V Output

Unit Vent Controller 0-10 V Output Install llation Instruction ons Document No. 540-205 Rev. 2, January, 1999 Unit Vent Controller 0-10 V Output Produ oduct Description These instructions explain how to field install (pages 1 through 3)

More information

BACnet Flow Controller for Fan Filter Units

BACnet Flow Controller for Fan Filter Units MANUAL SERVICE + INSTALLATION BACnet Flow Controller for Fan Filter Units BFC Series v300 Issue Date: 08/23/17 2017 Price Industries Limited. All rights reserved. TABLE OF CONTENTS Product Overview General

More information

Siemens BACnet Programmable TEC Constant Volume

Siemens BACnet Programmable TEC Constant Volume Technical Specification Sheet Document No. 149-852 September 24, 2014 Siemens BACnet Programmable TEC Constant Volume Returns from power failure without operator intervention. No calibration required,

More information

M1000 INTELLIGENT ZONE CONTROL SYSTEM

M1000 INTELLIGENT ZONE CONTROL SYSTEM HARDWARE GUIDE DIMENSIONS & SPECIFICATIONS REV. 5.2 M1000 INTELLIGENT ZONE CONTROL SYSTEM ROOFTOP CONTROLLER 2 Table of Contents GENERAL INFORMATION... 3 PL-M1000 Rooftop Controller...3 Description...3

More information

RXB39.1. Room controller RXB. Communicating room controller for fan-coil applications FC-13

RXB39.1. Room controller RXB. Communicating room controller for fan-coil applications FC-13 s 3 875 RXB Room controller Communicating room controller for fan-coil applications FC-13 RXB39.1 The RXB39.1 room controller is used for temperature control in individual rooms. For 2-pipe or 4-pipe fan-coil

More information

RXM39.1. PL-Link IO Block. Desigo TRA. Use with PXC3 series room automation station

RXM39.1. PL-Link IO Block. Desigo TRA. Use with PXC3 series room automation station s 3 836 3836P01 Desigo TRA PL-Link IO Block Use with PXC3 series room automation station RXM39.1 The PL-Link IO Block contains the inputs and outputs controlled by a room automation station via PL-Link.

More information

RDF Series Room Temperature Controllers

RDF Series Room Temperature Controllers Document No. 19-49 RDF Series Room Temperature Controllers Product Description Room Temperature Controllers with LCD for twopipe (with and without an electrical heater) and fourpipe fan coil units. Installation

More information

XT-9100 Technical Bulletin

XT-9100 Technical Bulletin System 9100 Technical Manual 636.4 Technical Bulletins Section Technical Bulletin Issue Date 0896 XT-9100 Technical Bulletin XT-9100 Extension Module/XP-910x Expansion Modules Page 3 Introduction 3 SX

More information

Actuating Terminal Equipment Controller (ATEC) VAV with Reheat. Start-up Procedures Building Technologies Restricted

Actuating Terminal Equipment Controller (ATEC) VAV with Reheat. Start-up Procedures Building Technologies Restricted Actuating Terminal Equipment Controller (ATEC) VAV with Reheat Start-up Procedures 140-1202 Building Technologies 2015-05-06 Restricted Table of Contents... 4 Verifying Power to the Controller... 4 Setting

More information

Electrical Demand Specification (Reference SOP: )

Electrical Demand Specification (Reference SOP: ) Project: Equipment Description: Location: Equipment No.: Project No: Protocol No.: Content Index 1. GENERAL...3 Design Standards...3 1.1. Standards...3 2. DESIGN...3 2.1. Safety...3 2.2. Circuit protection...3

More information

Datasheet. ECB-PTU Series. 1/14. BACnet B-ASC Powered Terminal Unit Programmable Controllers. Overview

Datasheet. ECB-PTU Series.  1/14. BACnet B-ASC Powered Terminal Unit Programmable Controllers. Overview Datasheet BACnet B-ASC Powered Terminal Unit Programmable Controllers Overview Applications Meets the requirements of the following applications: Fan Coil Units Heat Pumps Chilled Beams Reversible Ceiling

More information

Modular Room Control (MRC) Series Expansion Board

Modular Room Control (MRC) Series Expansion Board Installation Instructions Issue Date December 13, 2002 Modular Room Control (MRC) Series Expansion Board Application The Modular Room Control (MRC) system has the ability to expand its input/output capabilities

More information

TX-I/O Product Range. Features. Description. Technical Specification Sheet Document No January 24, 2007

TX-I/O Product Range. Features. Description. Technical Specification Sheet Document No January 24, 2007 Technical Specification Sheet Document No. 149-476 January 24, 2007 TX-I/O Product Range Description TX-I/O is a line of I/O modules with associated power and communication modules for use within the APOGEE

More information

Siemens BACnet Programmable TEC VAV with Series Fan and 3-Stage Electric Heat Controller

Siemens BACnet Programmable TEC VAV with Series Fan and 3-Stage Electric Heat Controller Technical Specification Sheet Document No. 149-834 August 23, 2010 Siemens BACnet Programmable TEC VAV with Series Fan and 3-Stage Electric Heat Controller The Siemens BACnet PTEC VAV with Series Fan and

More information

AppController overview and specifications

AppController overview and specifications AppController CARRIER CORPORATION 2018 A member of the United Technologies Corporation family Stock symbol UTX Catalog No. 11-808-477-01 2/28/2018 Verify that you have the most current version of this

More information

VC3000 Series Line Voltage Switching Relay Pack Controllers Installation Guide

VC3000 Series Line Voltage Switching Relay Pack Controllers Installation Guide Beyond Comfort VC3000 Series Line Voltage Switching Relay Pack Controllers Installation Guide August 10 th, 2010 (For Commercial and Lodging HVAC Fan Coil Applications) 028-0296-R1-LIT-VC3000-E01 Index

More information

LYNX LON Programmable VAV/Unitary Controllers

LYNX LON Programmable VAV/Unitary Controllers LYNX LON Programmable VAV/Unitary Controllers Product Data GENERAL The LYNX controllers CLLYUL101S, CLLYUL404S, CLLYUL6438S, CLLYVL0000AS, CLLYVL40AS, CLLYVL404NS, CLLYVL6436AS, and CLLYVL6438NS are part

More information

BACnet PTEC Controller Constant Volume - Cooling Only, Application Application Note Building Technologies

BACnet PTEC Controller Constant Volume - Cooling Only, Application Application Note Building Technologies BACnet PTEC Controller Constant Volume - Cooling Only, Application 6660 Application Note 140-1107 Building Technologies Table of Contents Overview... 4 BACnet... 5 Hardware Inputs... 5 Room Unit Identification...

More information

RXL24.1. Room controller RXL. Communicating controller for chilled ceiling and radiator applications CC-02

RXL24.1. Room controller RXL. Communicating controller for chilled ceiling and radiator applications CC-02 s 3 878 RXL Room controller RXL24.1 Communicating controller for chilled ceiling and radiator applications CC-02 The RXL24.1 room controller is used for temperature control in individual rooms. For chilled

More information

AppController overview and specifications

AppController overview and specifications AppController CARRIER CORPORATION 2018 A member of the United Technologies Corporation family Stock symbol UTX Catalog No. 11-808-477-01 10/25/2018 Verify that you have the most current version of this

More information

599 Series Zone Valve Actuator SF Series Electronic Valve Actuator, 2-position Control

599 Series Zone Valve Actuator SF Series Electronic Valve Actuator, 2-position Control 599 Series Zone Valve Actuator SF Series Electronic Valve Actuator, 2-position Control Technical Instructions EA1021R1 Description The 599 SF Series electronic zone valve actuators, accepts 24 Vac, 120

More information

H7625B; H7635B,C; H7655B Duct-Mount and Outdoor-Mount Humidity/Temperature Sensors

H7625B; H7635B,C; H7655B Duct-Mount and Outdoor-Mount Humidity/Temperature Sensors H765B; H7635B,C; H7655B Duct-Mount and Outdoor-Mount Humidity/Temperature Sensors APPLICATION The H765B, H7635B, H7655B Duct-Mount and H7635C Outdoor-Mount Humidity/Temperature Sensors are universal Relative

More information

MNL-V1RVx MNL-V2RVx. Application. Model Chart. TAC I/A Series MicroNet Variable Air Volume Controllers Installation Instructions

MNL-V1RVx MNL-V2RVx. Application. Model Chart. TAC I/A Series MicroNet Variable Air Volume Controllers Installation Instructions TAC 1354 Clifford Avenue P. O. Box 2940 Loves Park, IL 61132-2940 www.tac.com MNL-V1RVx MNL-V2RVx TAC I/A Series MicroNet Variable Air Volume Controllers Installation Instructions Application TAC I/A Series

More information

User s Manual. ACS550-PD 3R Irrigation Packaged Drive Supplement to ACS550-U1 User s Manual

User s Manual. ACS550-PD 3R Irrigation Packaged Drive Supplement to ACS550-U1 User s Manual User s Manual ACS550-PD 3R Irrigation Packaged Drive Supplement to ACS550-U1 User s Manual 2 ACS550-PD 3R Irrigation Packaged Drive ACS550 Drive Manuals GENERAL MANUALS ACS550-U1 User s Manual (1 200 HP)

More information

Installation Job Aid for Ethernet Routing Switch 3600 Series

Installation Job Aid for Ethernet Routing Switch 3600 Series Installation Job Aid for Ethernet Routing Switch 3600 Series Notices NN47213-303 Issue 03.01 November 2017 Notice paragraphs alert you about issues that require your attention. Following are descriptions

More information

FEATURES DESCRIPTION MODEL 110B. Power Supply

FEATURES DESCRIPTION MODEL 110B. Power Supply FEATURES Extends wiring distance of FT-10 LonWorks Networks. (2) channels using a single Model 110B. Up to 10 channels using (5) Model 110B. Low cost alternative to routers configured as repeaters. Wring

More information

Spyder Lon Programmable, VAV/Unitary Controllers

Spyder Lon Programmable, VAV/Unitary Controllers Spyder Lon Programmable, VAV/Unitary Controllers Controller Model Programmable Type Universal Inputs (UI) Table. Controller configurations. Digital Inputs (DI) PRODUCT DATA PRODUCT DESCRIPTION The PUL0S,

More information

Siemens BACnet Programmable TEC Dual Duct Two Air Velocity Sensors Controller

Siemens BACnet Programmable TEC Dual Duct Two Air Velocity Sensors Controller Technical Specification Sheet Document No. 149-851 September 24, 2014 Siemens BACnet Programmable TEC Dual Duct Two Air Velocity Sensors Controller The Siemens BACnet PTEC Dual Duct Controller provides

More information

Dual Duct Controller - One Air Velocity

Dual Duct Controller - One Air Velocity Technical Specification Sheet Rev. 4, December, 1998 Dual Duct Controller - One Air Velocity Sensor gure 1. Dual Duct Con ontr troll ller One Air Velocity Sen ensor. The Dual Duct Controller (re 1) is

More information

VertX. V100, V200 and V300. Installation Guide Barranca Parkway Irvine, CA USA. November Rev A.1

VertX. V100, V200 and V300. Installation Guide Barranca Parkway Irvine, CA USA. November Rev A.1 15370 Barranca Parkway Irvine, CA 92618 USA VertX V100, V200 and V300 Installation Guide November 2011 6080-930 Rev A.1. Contents Introduction... 3 Parts List... 3 Product Specifications... 3 Cable Specifications...

More information

COND. A ENABLE RELAY CONTACT COOLA ENABLE 24 VAC. RATING IS 1 AMP COND. B ENABLE COOL B ENABLE.

COND. A ENABLE RELAY CONTACT COOLA ENABLE 24 VAC.   RATING IS 1 AMP COND. B ENABLE COOL B ENABLE. Factory Packaged Controls Coil Products Two Head Pressure Module Orion No.:OE370-23-HP2C 1 2 3 4 www.aaon.com www.orioncontrols.com Circuit A1 TRANSDUCER #1 Circuit A2 TRANSDUCER #2 Circuit B1 TRANSDUCER

More information

TALON Network Manager- 2 & 6 Express

TALON Network Manager- 2 & 6 Express Technical Specification Sheet October 30, 2010 TALON Network Manager- 2 & 6 Express Description The TALON Network Manager-2 & 6 Express (TNM-2 XPR and TNM-6 XPR) is an embedded controller/server platform

More information

Powermite 599 MT Series SAS Electronic Valve Actuator 24 Vac or 24 Vdc, Proportional Control

Powermite 599 MT Series SAS Electronic Valve Actuator 24 Vac or 24 Vdc, Proportional Control Powermite 599 MT Series SAS Electronic Valve Actuator 24 Vac or 24 Vdc, Proportional Control Description Features Application The Powermite 599 MT Series SAS Electronic Valve Actuator requires a 24 Vac

More information

IQ-SBS LCU Series Installation Instructions

IQ-SBS LCU Series Installation Instructions Installation Instructions LCU-1 The IQ-SBS LCU-1 is a self-contained device for integrating control of facility lighting with IQ-SBS. The LCU-1 controls lighting zones, accepts input from override switches

More information

GF90 Installation, Operation and Troubleshooting Guide

GF90 Installation, Operation and Troubleshooting Guide 24 Hour Factory Service Hot Line: 1 (800) 854-1993 GF90 Installation, Operation and Troubleshooting Guide Document 06EN003319 Rev. - A. To get the best results from the instrument, the sensor should be

More information

BACnet Terminal Box (VAV) Controller

BACnet Terminal Box (VAV) Controller Technical Specification Sheet May 30, 2012 BACnet Terminal Box (VAV) Controller Figure 1. BACnet Terminal Box Controller. The BACnet Terminal Box Controller (Figure 1) provides high performance Direct

More information