Loctite Light Intensity Monitor Part Number EQUIPMENT Operation Manual. Light Intensity Monitor. Item No Set to 100% Run Mode

Size: px
Start display at page:

Download "Loctite Light Intensity Monitor Part Number EQUIPMENT Operation Manual. Light Intensity Monitor. Item No Set to 100% Run Mode"

Transcription

1 O N EQUIPMENT Operation Manual Run Mode Set Mode 100% 100% 50% 10% Lamp Fault Lamp Strength Fault Point Select Power On Set to 100% Light Intensity Monitor Item No Loctite Light Intensity Monitor Part Number

2 1.1 Emphasized Sections 1 Please Observe the Following WARNING! Refers to safety regulations and requires measures to protect the operator and others from injury or danger to life. Caution! Emphasizes what must be done or avoided so that the unit or other property is not damaged. Notice: Gives recommendations for better handling of the unit during operation or adjustment, as well as for service activities. 1.2 Items Supplied 1 Intensity Monitor, part # Shielded power cord, part # Users manual, part # Sensor cable, part # Shutter signal cable, (for use with shuttered curing systems only), part # For Your Safety For safe and successful operation of the unit, read these instructions completely. If the instructions are not observed, the manufacturer can assume no responsibility. Be sure to retain this manual for future reference. WARNING! Never remove the cover of the unit without first switching the power off and unplugging the power cord. WARNING! Damage to the power cord or the housing can result in contact with live electrical parts. Check the power cord and housing before each use. If the power cord or unit is damaged, do not operate. The unit must only be repaired by a Henkel authorized service technician. Caution! Avoid touching or scratching the lens of the photo-sensor. 1.4 Field of Application, (Intended Usage) The Loctite Light Intensity Monitoring System is designed to operate with all Loctite light curing systems. Notice: The monitor requires installation of a Loctite light sensor kit , (sold as a separate item), in the curing unit.

3 2 Description 2.1 Theory of Operation The Light Intensity Monitoring System continuously monitors the intensity of the curing lamps used in Loctite light curing systems. The light sensor, installed in close proximity to the curing lamp, produces an electrical current proportional to the incident light that originates from the curing lamp. That signal is received by the monitoring unit by means of a cable and a nine pin D-sub connector located on the rear panel of the monitor. When a new lamp is installed, the monitoring system is manually set to 100%. The yellow LED will light to confirm that the system is adjusted to 100%. The lamp intensity is indicated in ten percent increments by an LED bar graph located on the front panel. When the Light Intensity Monitor is used with a shuttered curing system such as a Loctite wand system, the shutter is controlled from the monitoring system either manually, (using the footswitch port on the rear panel of the monitor), or by a control device such as a PLC, (pins 1 and 9 of the I/O to PLC port). The monitor provides a signal to the PLC or other control device to indicate that the lamp intensity has fallen below a preset limit. That point of minimum allowable intensity is selected using the eight dip switches located on the front panel next to the LED display. The switches correspond to increments from 80 to 10 percent, (20 to 90 percent loss of intensity). As long as the intensity is greater than the preset fault point, the fault relay in the monitoring system is energized and the contacts remain closed. The contacts are connected to pins 3 and 4 of the nine pin D-sub output connector labeled I/O to PLC. When the intensity falls below the preset minimum, the red LED on the front panel will flash and the closed relay contacts will open, indicating a fault condition. Also, if the curing unit is outfitted with a shutter, it will be disabled. The shutter disable feature can be overridden by setting the slide switch in the monitor. 3 Technical/Physical Data Input voltage: VAC; 50/60 Hz Main fuse located in the input module: 1A/250V Housing dimensions: 5 ½ x 6 x 6 inches, (height x width x depth) Weight: 4 lbs

4 4 Installation 4.1 Connections - Connect one end of the sensor cable, (female on both ends), to the male nine pin D-sub input labeled Light Sensor Input on the rear panel of the monitor system. Connect the other end to the cable to the connector labeled Light Sensor Output on the curing unit. The sensor signal is transmitted across pins 3 and 4. Pin 5 is connected to case ground. - Pins 1 and 9 are used for shutter control in Loctite shuttered systems. Connect one end of the shutter connection cable, (male on both ends), to the 9 pin D-sub connector located on the curing system. Connect the opposite end to the connector on the rear panel of the monitor labeled, Shutter Output. - If the monitor is connected to a PLC, install a cable, (not included), from the output connector of the monitoring system labeled I/O to PLC to the PLC input. Closure across pins 1 and 9 controls the wand system shutter. Pins 3 and 4 are the fault relay output, (open indicates an intensity fault condition). - Connect the power cord to the power entry module on the rear panel and plug into power source. I/O to PLC - Connects shutter signal, (pins 1 and 9), and fault signal, (pins 3 and 4), from monitor to PLC. Shutter Output - Connects shutter signal from curing system to monitor, (pins 1 and 9). Note: Pins 1 and 9 of the Shutter Output port are connected in parallel with pins 1 and 9 of the I/O to PLC port. Foot Pedal Connects to a remote footswitch or other manual shutter control. Pins 1 and 9 are in parallel with pins 1 and 9 of the I/O to PLC and Shutter Output ports. Light Sensor Input Input for the light sensor located in the curing unit. Pins 3 and 4 are the anode and cathode, respectively, and pin 5 is shield to case ground. 5 Operating the System 5.1 Powering up - After making the connections described in section 4, switch on the power to the curing system and the monitoring system. Notice: Avoid turning the monitor on without the having the photosensor connected. 5.2 Setting the System to 100% Notice: The procedure described in this section must be repeated each time and only when a new lamp is installed. The Set to100% adjustment must not be changed again

5 until a new lamp is installed. It is recommended that the absolute intensity be measured at the time of this procedure using a Loctite radiometer. - Allow the curing lamp to reach its maximum output. The warm-up period is specified in the curing unit s manual. If the warm-up time is not known, allow a minimum of ten minutes. - Set the toggle switch on the front panel to Set Mode, (all segments of the LED bar graph will light). - If the yellow LED located above the adjustment is lit, turn the Set to 100% adjustment clockwise until the LED turns off. Then slowly turn the adjustment counter-clockwise, stopping when the LED turns on. The yellow LED confirms that the system is properly set. Do not continue to turn the adjustment beyond the point where the LED turns on. - If the yellow LED is not lit when the in Set mode, slowly turn the adjustment counter-clockwise, stopping when the LED turns on. As in the previous step, do not continue to turn the adjustment beyond the point where the LED turns on. - Switch the system to Run Mode, (the yellow LED will immediately go out). - All segments of the bar graph should be on, indicating that the lamp is at 100% strength. If less than 100% is indicated, repeat the procedure. 5.3 Setting the lamp fault point (Note: if a fault point is not selected, the system will indicate a fault condition) - Select the intensity level where the system is to indicate that the lamp needs to be replaced. (10% to 80% in increments of 10%), - Set the dip switch corresponding to the chosen fault point to the on position, (left). Each dip switch represents a 10% increment from 80 to 10%. - Make sure that all other dip switches in the off position, (right) Example: The lamp is to be replaced when the intensity falls below 50% of the initial intensity. Set the fourth switch from the top ON position, (slide to the left). All other switches should be in the OFF position, (to the right). 5.4 Shutter Disable Feature, (applies to curing systems with shutters, only) When the chosen intensity fault point is reached the monitor will disable the shutter in the curing unit. To override this feature remove the enclosure lid from the monitor. Locate the slide switch positioned near the center of the top circuit board. Switch it from the ON position, (factory setting), to the OFF position. 5.5 Continuous Operation After completing the steps in sections 5.1 through 5.3, the system will continuously monitor the lamp output. It is normal for the highest LED bar that is lit to dim as it approaches the point of turning off. When the lamp output reaches the fault point, the red LED on the front panel will flash, the relay output will change state from closed to open and the curing unit shutter will be disabled. Note that when the curing system is first started, the monitor will indicate a fault condition until the lamp warms up to the point that the intensity exceeds the chosen fault point.

6 6 Care and Maintenance Caution! Avoid touching, contaminating or scratching the photo-sensor lens. The photosensor is located in the curing unit. Notice: The Light Intensity Monitoring System requires very little maintenance. To insure continued reliable operation, it is recommended that the photodiode lens be checked for cleanliness. Isopropyl alcohol should be used with a clean wiper to remove any contaminants. 7 Troubleshooting Condition Possible Cause Corrections The LED bar graph does not come on The curing lamp is not on. Check the lamp function. but the main power is on. The system is not set to 100%. Repeat procedure in section 5.2. None of the functions work and The unit is not plugged in. Check the main power. the main power indicator is out. The main fuse is blown. Check fuse in power module. The yellow LED will not light The lamp is not on. Check the lamp function. during the Set 100% procedure. The lamp output is too low. Check irradiance level of lamp. The system is not in SET mode. Switch toggle to Set mode. A fault is indicated while the LED The dip switches are not Check, re-set the dip switches. bars show intensity to be above properly set. the preset minimum point. The sensor is disconnected. Inspect sensor connections from curing system to monitor. The curing unit shutter will not operate. The shutter signal connections Refer to 4.1 Connections. are not properly configured. Faulty connection. Inspect solder connections on D-sub connectors. Check continuity across cables. The monitor does not disable the shutter Internal bypass switch is Check bypass switch state in when a fault occurs. set to OFF monitor.

7 Light Intensity Monitor Layout Run Mode Set Mode Lamp Fault Fault Point Lamp Strength Select 100% POWER ON 100% 50% Set to 100% 10% INTENSITY MONITOR I/O to PLC Light Sensor Input Shutter Output Warning Disconnect and Refer to Manual Before Servicing Unit. Foot Pedal

8 LED Bar Graph and Fault Point Select Switches Lamp Strength Fault Point Select

9 Warranty Henkel expressly warrants that all products referred to in this Instruction Manual for the Light Intensity Monitor, (hereafter called Product ), shall be free from defects in materials and workmanship. Liability for Henkel shall be limited, as its option, to replacing those Products which are shown to be defective in either materials or workmanship or to credit the purchaser the amount of the purchase price thereof (plus freight and insurance charges paid therefore by the user). The purchaser s sole and exclusive remedy for breach of warranty shall be such replacement or credit. A claim of defect in materials or workmanship in any Product shall be allowed only when it is submitted in writing within one month after discovery of the defect or after the time the defect should reasonably have been discovered and in any event, within 1 year after the delivery of the Products to the purchaser. This warranty does not apply to perishable items, such as fuses. No such claim shall be allowed in respect of products which have been neglected or improperly stored, transported, handled, installed, connected, operated, used or maintained. In the event of unauthorized modification of the Products including, where products, parts or attachments for use in connection with the Products are available from Loctite, the use of products, parts or attachments which are not manufactured by Henkel, no claim shall be allowed. No Products shall be returned to Henkel for any reason without prior written approval from Henkel. Products shall be returned freight prepaid, in accordance with instructions from Henkel. NO WARRANTY IS EXTENDED TO ANY EQUIPMENT WHICH HAS BEEN ALTERED, MISUSED, NEGLECTED, OR DAMAGED BY ACCIDENT, OR IF THE SYSTEM USED TO DISPENSE ANY LIQUID MATERIAL OTHER THAN LOCTITE PRODUCTS. EXCEPT FOR THE EXPRESS WARRANTY CONTAINED IN THIS SECTION, HENKEL MAKES NO WARRANTY OF ANY KIND WHATSOEVER, EXPRESS OR IMPLIED, WITH RESPECT TO THE PRODUCTS. ALL WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND OTHER WARRANTIES OF WHATEVER KIND (INCLUDING AGAINST PATENT OR TRADEMARK INFRINGEMENT) ARE HEREBY DISCLAIMED BY HENKEL AND WAIVED BY THE PURCHASER. THIS SECTION SETS FORTH EXCLUSIVELY ALL LIABILITY FOR HENKEL TO THE PURCHASER IN CONTRACT, IN TORT OR OTHERWISE IN THE EVENT OF DEFECTIVE PRODUCTS. WITHOUT LIMITATION OF THE FOREGOING, TO THE FULLEST EXTENT POSSIBLE UNDER APPLICABLE LAWS, HENKEL EXPRESSLY DISCLAIMS ANY LIABILITY WHATSOEVER FOR ANY DAMAGES INCURRED DIRECTLY OR INDIRECTLY IN CONNECTION WITH THE SALE OR USE OF, OR OTHERWISE IN CONNECTION WITH, THE PRODUCTS, INCLUDING, WITHOUT LIMITATION, LOSS OF PROFITS AND SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES, WHETHER CAUSED BY NEGLIGENCE FROM HENKEL OR OTHERWISE.

10 Henkel Corporation 1001 Trout Brook Crossing Rocky Hill, CT Henkel Automotive Technology Center 2455 Featherstone Road Auburn Hills, Michigan Henkel Canada Corporation 2225 Meadowpine Boulevard Mississauga, Ontario L5N 7P2 Henkel Ltda. Rua Karl Huller, 136 Jd. Canhema Diadema/SP, Brazil Henkel Capital, S.A. de C.V. Calzada de la Viga s/n Fracc. Los Laureles Loc. Tulpetlac, C.P Ecatepac de Morelos, Edo. de México Loctite is a trademark of Henkel Corporation, U.S.A. Copyright Henkel Corporation All rights reserved. Data in this operation manual is subject to change without notice. Manual P/N: , Date: 10/2006

11

Operation Manual. Equipment. Operation Manual. Loctite RB30 Robot Camera. Part Number:

Operation Manual. Equipment. Operation Manual. Loctite RB30 Robot Camera. Part Number: Operation Manual Equipment Operation Manual Loctite RB30 Robot Camera Part Number: 1912406 Operation Manual 1 1.1 1.2 1.3 1.4 1.5 2 2.1 2.2 3 3.1 3.2 3.3 4 5 Table of Contents Please Observe the Following...3

More information

EQUIPMENT Operation Manual

EQUIPMENT Operation Manual EQUIPMENT Operation Manual 7700 Label # 988830 Loctite Handheld LED Light Sources Part Number 1427231 Model 7700 Light Source II Part Number 98595 Model 7703 Light Source TABLE OF CONTENTS 1. PLEASE OBSERVE

More information

EQUIPMENT Operation Manual

EQUIPMENT Operation Manual EQUIPMENT Operation Manual Loctite LED Light Sources Part Number 1427232 Model 7700-HD, LED Light Source II, 395 nm Peak Part Number 98665 Model 7703-HD, >400 nm Pure Visible Light Source 1 TABLE OF CONTENTS

More information

Loctite CL20 LED ARRAY 4 CHANNEL SYSTEM. EQUIPMENT Operation Manual. CL20 Controller Part Number: CL20 Expansion Module Part Number:

Loctite CL20 LED ARRAY 4 CHANNEL SYSTEM. EQUIPMENT Operation Manual. CL20 Controller Part Number: CL20 Expansion Module Part Number: EQUIPMENT Operation Manual Loctite CL20 LED ARRAY 4 CHANNEL SYSTEM CL20 Controller Part Number: 1470725 CL20 Expansion Module Part Number: 1488502 Array Part Numbers: 1488449 (405 Flood Array) 1492915

More information

EQUIPMENT Operation Manual

EQUIPMENT Operation Manual EQUIPMENT Operation Manual Loctite Four Event Timer Part Number 98159 Four Event Timer for 115 and 230 VAC Contents 1. PLEASE OBSERVE THE FOLLOWING 1.1 EMPHASIZED SECTIONS 1.2 FOR YOUR SAFETY 2. DESCRIPTION

More information

Loctite Digital Multi-Functional Controller Part Number EQUIPMENT Operation Manual

Loctite Digital Multi-Functional Controller Part Number EQUIPMENT Operation Manual Loctite Digital Multi-Functional Controller Part Number 0006 EQUIPMENT Operation Manual TABLE OF CTENTS. PLEASE OBSERVE THE FOLLOWING...3. EMPHASIZED SECTIS... 3. ITEMS SUPPLIED... 3.3 FOR YOUR SAFETY...

More information

EQ CL30 LED Quad Controller. Operating Manual

EQ CL30 LED Quad Controller. Operating Manual 2257357 EQ CL30 LED Quad Controller Operating Manual 1 Table of Contents 1 Please Observe the Following... 3 1.1 Emphasized Sections... 3 1.2 For Your Safety... 3 1.3 Unpacking and Inspection... 5 1.4

More information

EQ ACCE Robot D-Series Junc Box 24V IDH #: Equipment Instructions

EQ ACCE Robot D-Series Junc Box 24V IDH #: Equipment Instructions EQ ACCE Robot D-Series Junc Box 24V IDH #: 2182205 Table of Contents 1 Please Observe the Following... 3 1.1. Emphasized Sections... 3 1.2. For Your Safety... 3 1.3. Unpacking and Inspection... 4 1.4.

More information

EQ ACCE D-Series Robot Software Kit. Operating Manual

EQ ACCE D-Series Robot Software Kit. Operating Manual 2148218 EQ ACCE D-Series Robot Software Kit Operating Manual 1 Table of Contents 1 Please Observe The Following... 4 1.1 Emphasized Sections... 4 1.2 For Your Safety... 4 1.3 Unpacking and Inspection...

More information

MiT. MOVING image TECHNOLOGIES INSTRUCTIONS FOR INSTALLATION, OPERATION, AND MAINTENANCE

MiT. MOVING image TECHNOLOGIES INSTRUCTIONS FOR INSTALLATION, OPERATION, AND MAINTENANCE MiT MOVING image TECHNOLOGIES INSTRUCTIONS FOR INSTALLATION, OPERATION, AND MAINTENANCE OF A-LMS 24 Architectural Lighting Management System Part number A000230-xxx Manual Version 1.0 MOVING image TECHNOLOGIES,

More information

EASON TECHNOLOGY. IO8 & IO24 Break-Out Module

EASON TECHNOLOGY. IO8 & IO24 Break-Out Module EASON TECHNOLOGY IO8 & IO24 Break-Out Module p/n 50-00180-01 Revision1.2 Eason Technology, Inc. 7975 Cameron Dr. Bldg 300 Windsor, CA 95492 Phone (707) 837-0120 FAX (707) 837-2742 http://www.eason.com

More information

Woolich Racing. USB ECU Interface User Guide

Woolich Racing. USB ECU Interface User Guide Woolich Racing USB ECU Interface User Guide 1) Introduction This user guide covers how to use the Woolich Racing USB ECU Interface. This includes: Connecting the USB ECU Interface into the Bike Harness

More information

PIM-Mini Pulsed Current Source Operation Manual

PIM-Mini Pulsed Current Source Operation Manual PIM-Mini Pulsed Current Source Operation Manual Directed Energy, Inc. 1609 Oakridge Dr., Suite 100, Fort Collins, CO 80525 (970) 493-1901 sales@ixyscolorado.com www.ixyscolorado.com Manual Document 7650-0007

More information

FTC-200 X-ray Tube Controller Users Manual

FTC-200 X-ray Tube Controller Users Manual Tubes FTC-200 X-ray Tube Controller TUB-MAN-2101 Rev. A 09/09/2009TTUB Table of Contents List of Tables...3 List of Figures...3 Introduction...3 Manual Set...3 About this Manual...4 X-Ray Safety Information...4

More information

User Guide. Control Box. RoscoLED TM.

User Guide. Control Box. RoscoLED TM. RoscoLED TM Control Box User Guide This guide applies to the following RoscoLED Control Box models: RoscoLED Control Box 300W/Static White (293 22250 0000) RoscoLED Control Box 400W/VariWhite (293 22260

More information

Sonic Ruptor 400. User Manual

Sonic Ruptor 400. User Manual Sonic Ruptor 400 User Manual Data herein has been verified and validated. It is believed adequate for the intended use of the instrument. If the instrument or procedures are used for purposes over and

More information

Install Motor Controller User Manual

Install Motor Controller User Manual Property of Motion Laboratories, Inc. Install Motor Controller User Manual 2014 Motion Laboratories, Inc. Created By: Michael Shaw Approved By: John Coppolecchia Page: 1 Page: 2 2014 Motion Laboratories,

More information

500 Business Center Drive Pittsburgh, PA USA CAGE 1BGJ7. SwitchMaster R5000 Series Ultra-Compact Ganged A/B Switching System

500 Business Center Drive Pittsburgh, PA USA CAGE 1BGJ7. SwitchMaster R5000 Series Ultra-Compact Ganged A/B Switching System Market Central www.secureswitch.com 500 Business Center Drive Pittsburgh, PA 15205 USA 412.494.2800 CAGE 1BGJ7 SwitchMaster R5000 Series Ultra-Compact Ganged A/B Switching System July, 2014 COMPLETE 2

More information

PSA200 User s Manual

PSA200 User s Manual 2011 Visionary Solutions, Inc. All rights reserved. Please visit the support section of our website at www.vsicam.com for manuals, other documentation, and software downloads. Visionary Solutions, Inc.

More information

INSTRUCTION MANUAL 4 UNIT AES SWITCH MODEL R198 S/N

INSTRUCTION MANUAL 4 UNIT AES SWITCH MODEL R198 S/N INSTRUCTION MANUAL 4 UNIT AES SWITCH MODEL R198 S/N IF FOR SOME REASON YOU HAVE TO RETURN THIS ITEM TO THE FACTORY FOR ANY SERVICE OR REPAIR, YOU MUST CONTACT CUSTOMER SERVICE FOR AN RMA NUMBER AT (585)

More information

SATA II HDD Canister KISS DA 435 Quick Reference Guide

SATA II HDD Canister KISS DA 435 Quick Reference Guide SATA II HDD Canister KISS DA 435 Quick Reference Guide If it s embedded, it s Kontron 1. Table of Contents SATA II HDD Canister KISS DA 435 1. Table of Contents 1. Table of Contents... 1 2. Important Information...

More information

WCC100 IN-VEHICLE CHARGING CRADLE OWNER S MANUAL

WCC100 IN-VEHICLE CHARGING CRADLE OWNER S MANUAL WCC100 IN-VEHICLE CHARGING CRADLE OWNER S MANUAL 128-9237B WCC100 In-Vehicle Charging Cradle 12 03 13.indd 1 12/4/2013 10:38:04 AM 128-9237B WCC100 In-Vehicle Charging Cradle 12 03 13.indd 2 12/4/2013

More information

PCM-7140 Pulsed Current Source Operation Manual

PCM-7140 Pulsed Current Source Operation Manual PCM-7140 Pulsed Current Source Operation Manual Directed Energy, Inc. 1609 Oakridge Dr., Suite 100, Fort Collins, CO 80525 (970) 493-1901 sales@ixyscolorado.com www.ixyscolorado.com Manual Document 7650-0031

More information

OPERATING AND SERVICE MANUAL. Universal Interface Device 47

OPERATING AND SERVICE MANUAL. Universal Interface Device 47 OPERATING AND SERVICE MANUAL Universal Interface Device 47 MAGNA-POWER ELECTRONICS, INC. 39 ROYAL ROAD, FLEMINGTON, NJ 08822 May 24, 2012 SAFETY NOTICE Universal Interface Device 47 (UID46) connects

More information

COOPER POWER SERIES. Input/Output (I/O) module installation instructions. Voltage Regulators MN225067EN

COOPER POWER SERIES. Input/Output (I/O) module installation instructions. Voltage Regulators MN225067EN Voltage Regulators MN225067EN Effective November 2016 Supersedes June 2014 (S225-70-13) COOPER POWER Input/Output (I/O) module installation instructions SERIES DISCLAIMER OF WARRANTIES AND LIMITATION OF

More information

MPP200 User s Manual

MPP200 User s Manual 2011 Visionary Solutions, Inc. All rights reserved. Please visit the support section of our website at www.vsicam.com for manuals, other documentation, and software downloads. Visionary Solutions, Inc.

More information

User's Guide. Model High Precision Quad Output DC Power Supply

User's Guide. Model High Precision Quad Output DC Power Supply User's Guide Model 382270 High Precision Quad Output DC Power Supply Introduction Congratulations on your purchase of the Extech 382270 DC Power Supply. The Model 382270 can be used for many applications

More information

STAINLESS STEEL CAST FITTINGS 150lb 304 & 316 Stainless Steel Cast Fittings Specifications

STAINLESS STEEL CAST FITTINGS 150lb 304 & 316 Stainless Steel Cast Fittings Specifications STAINLESS STEEL CAST FITTINGS 150lb 304 & 316 Stainless Steel Cast Fittings Specifications Manufactured in ISO9000:2000 Facility Items Conform to AISI 304 / 316 Investment Cast SP114 Stainless Fittings

More information

OPERATING AND SERVICE MANUAL. Universal Interface Device 47

OPERATING AND SERVICE MANUAL. Universal Interface Device 47 OPERATING AND SERVICE MANUAL Universal Interface Device 47 MAGNA-POWER ELECTRONICS, INC. 39 ROYAL ROAD, FLEMINGTON, NJ 08822 May 24, 202 SAFETY NOTICE Universal Interface Device 47 (UID47) connects two

More information

zpen-1080p Features zpen-1080p Layout

zpen-1080p Features zpen-1080p Layout 1 zpen-1080p Features CMOS image sensor with Low Light sensitivity HD 1080P up to 30fps, 720P up to 60fps H.264 compression Built-in micro SD card, supports up to 32GB One button operation Easily download

More information

DOCKING STATION FOR THE APPLE 13 MacBook

DOCKING STATION FOR THE APPLE 13 MacBook DOCKING STATION FOR THE APPLE 13 MacBook 2009 THANK YOU Thank you for purchasing the BookEndz Dock for your MacBook Computer. The purpose of the BookEndz Dock is to eliminate the hassles, headaches, wear

More information

Wall. No opening (Example: LA-030-W)

Wall. No opening (Example: LA-030-W) Thank you very much for choosing an EIZO product. Please read this User s Manual carefully to familiarize yourself with safe and effective usage procedures. Please retain this manual for future reference.

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS 3YEAR WARRANTY & LIMITATION OF LIABILITY TRI-TRONICS COMPANY, INC. warrants that the products delivered by it will be of the kind and quality described in the order or contract

More information

Instruction and Operation Manual. CRMS Contact Resistance Measurement System. Model Number Caution!

Instruction and Operation Manual. CRMS Contact Resistance Measurement System. Model Number Caution! Instruction and Operation Manual CRMS Contact Resistance Measurement System Model Number 16574-00 Caution! Be sure to read and become thoroughly familiar with the entire contents of this manual before

More information

THECHARGEHUB.COM. User Manual. For Square & Round Models

THECHARGEHUB.COM. User Manual. For Square & Round Models THECHARGEHUB.COM User Manual For Square & Round Models User Manual THECHARGEHUB.COM 7-Port USB Universal Charging Station Table of Contents General Safety Information...2 Care and Maintenance...3 Introduction...4

More information

Remote Refrigeration Control

Remote Refrigeration Control Remote Refrigeration Control Installation & Operation Bulletin No. H-IM-RRC June 2018 Part Number 25092901 Replaces H-IM-RRC (01/17) Remote Refrigeration Control Installation Start Up Troubleshooting Operation

More information

Card Nest Universal 12 position card nest for all K-AB cards above and all other K-AB cards.

Card Nest Universal 12 position card nest for all K-AB cards above and all other K-AB cards. Installation And Operation BASIC A/B SWITCHES K-AB-D25 K-AB-M34 SCOPE OF THIS DOCUMENT This document covers the following models: K-AB-D25 K-AB-D25-R K-AB-M34 K-AB-M34-R For the purposes of clarity, all

More information

IRB-MON O P E R A T I N G I N S T R U C T I O N S UNIVERSAL SAFETY PHOTOEYE U L M O N I T O R E D DEVICE

IRB-MON O P E R A T I N G I N S T R U C T I O N S UNIVERSAL SAFETY PHOTOEYE U L M O N I T O R E D DEVICE O P E R A T I N G I N S T R U C T I O N S IRB-MON UNIVERSAL SAFETY PHOTOEYE U L 3 2 5-2 0 1 6 M O N I T O R E D DEVICE 4564 Johnston Parkway, Cleveland, Ohio 44128 P. 800 426 9912 F. 216 518 9884 Sales

More information

IRB-MON UNIVERSAL SAFETY PHOTOEYE OPERATING UL MONITORED DEVICE

IRB-MON UNIVERSAL SAFETY PHOTOEYE OPERATING UL MONITORED DEVICE IRB-MON UNIVERSAL SAFETY PHOTOEYE OPERATING UL325-2016 MONITORED DEVICE 4564 Johnston Parkway, Cleveland, Ohio 44128 P. 800 426 9912 F. 216 518 9884 Sales Inquiries: salessupport@emxinc.com Technical Support:

More information

3-4 SAS/SATA II HDD Canister Entry version USER S MANUAL XC-34D1-SA10-0-R. Document number: MAN A

3-4 SAS/SATA II HDD Canister Entry version USER S MANUAL XC-34D1-SA10-0-R. Document number: MAN A 3-4 SAS/SATA II HDD Canister Entry version XC-34D1-SA10-0-R USER S MANUAL Document number: MAN-00077-A ii Preface Important Information Warranty Our product is warranted against defects in materials and

More information

URC Light Sensor SEN-LITE for use with MRX units containing sensor ports

URC Light Sensor SEN-LITE for use with MRX units containing sensor ports URC Light Sensor SEN-LITE for use with MRX units containing sensor ports URC Light Sensor SEN-LITE 2014 Universal Remote Control, Inc. The information in this Owner s Manual is copyright protected. No

More information

DCS-E 1kW Series, DLM-E 3kW & 4kW Power Supplies

DCS-E 1kW Series, DLM-E 3kW & 4kW Power Supplies DCS-E 1kW Series, DLM-E 3kW & 4kW Power Supplies M51A Option: Isolated Analog Programming Manual Power Supplies Elgar Electronics Corporation 9250 Brown Deer Road San Diego, CA 92121-2294 1-800-73ELGAR

More information

3.5 TFT LCD CCTV Service Viewer with Wristband LCD35SV

3.5 TFT LCD CCTV Service Viewer with Wristband LCD35SV User Manual 3.5 TFT LCD CCTV Service Viewer with Wristband LCD35SV LCD35SV is a type of product that summarizes views of first-line safety engineers and it is developed specially for technical personnel

More information

Grundfos MAGNA, GENI Module

Grundfos MAGNA, GENI Module GRUNDFOS INSTRUCTIONS Grundfos MAGNA, GENI Module Installation and operating instructions 2 Grundfos MAGNA, GENI Module Installation and operating instructions 4 3 LIMITED WARRANTY Products manufactured

More information

Motorized Filter Wheel FW-MOT-12.5 / FW-MOT-25

Motorized Filter Wheel FW-MOT-12.5 / FW-MOT-25 Motorized Filter Wheel FW-MOT-12.5 / FW-MOT-25 Andover Corporation 4 Commercial Drive Salem, New Hampshire 03079-2800 Tel: (603) 893-6888 US Toll Free: (888) 893-9992 Fax: (603) 893-6508 Email: techstaff@andovercorp.com

More information

XBDM. 1015LV, 1020LV, 1030LV, 1020HV Models USER & INSTALLATION MANUAL BYPASS DISTRIBUTION MODULE

XBDM. 1015LV, 1020LV, 1030LV, 1020HV Models USER & INSTALLATION MANUAL BYPASS DISTRIBUTION MODULE XBDM 1015LV, 1020LV, 1030LV, 1020HV Models USER & INSTALLATION MANUAL www.xpcc.com 2013 Xtreme Power Conversion Corporation. All rights reserved. Table of Contents IMPORTANT SAFETY INSTRUCTIONS:... 4 INTRODUCTION...

More information

Tornado F-5. Motor Backspin Detect Relay And Probe For F-5 Motor Controller

Tornado F-5. Motor Backspin Detect Relay And Probe For F-5 Motor Controller Tornado F-5 Motor Backspin Detect Relay And Probe For F-5 Motor Controller Tornado F-5 Motor Backspin Detection Relay And Probe Revision 8.1 Change Log: Rev 8.1 Apr 24 2012 JNesbitt@GPS-US.co GPS updates

More information

PMDX-108-Output. 8-Channel Isolated Output Board for PC parallel port pins 2-9. User s Manual

PMDX-108-Output. 8-Channel Isolated Output Board for PC parallel port pins 2-9. User s Manual PMDX-108-Output 8-Channel Isolated Output Board for PC parallel port pins 2-9 User s Manual Date: 25 February 2010 PMDX Web: http://www.pmdx.com 9704-D Gunston Cove Rd Phone: +1 (703) 372-2975 Lorton,

More information

Macon Plastics, Inc. Solvent Weld SCH 40/80 DWV

Macon Plastics, Inc. Solvent Weld SCH 40/80 DWV Catalog #210SDWV MP Macon Plastics, Inc. & DWV Fittings P R I C E L I S T Solvent Weld /80 DWV Effective Date: 02/02/15 Catalog : 210SDWV Revision: D Supercedes: 209SDWV Not sure if you have a current

More information

PagePac PAGEPAC PLUS ZONE EXPANSION UNIT V

PagePac PAGEPAC PLUS ZONE EXPANSION UNIT V PagePac Issue 3 by PAGEPAC PLUS ZONE EXPANSION UNIT V-5335100 INTRODUCTION The Zone Expansion Unit (ZEU) provides up to 16 zones of audio output (including talkback), contact closure outputs or inputs.

More information

PMDX-105. I/O Option Riser Board User s Manual. Document Revision: 1.1 Date: 7 September 2004 PCB Revision: PCB-443A

PMDX-105. I/O Option Riser Board User s Manual. Document Revision: 1.1 Date: 7 September 2004 PCB Revision: PCB-443A PMDX-105 I/O Option Riser Board User s Manual Date: 7 September 2004 PMDX Web: http://www.pmdx.com 7432 Alban Station Blvd., A105 Phone: +1 (703) 912-4991 Springfield, VA 22150-2321 USA FAX: +1 (703) 912-5849

More information

Enable-IT 821 Ethernet Extender Quickstart Guide Professional Grade Networking

Enable-IT 821 Ethernet Extender Quickstart Guide Professional Grade Networking ! Enable-IT 821 Ethernet Extender Quickstart Guide Professional Grade Networking All Rights Reserved 1997-2017 Enable-IT, Inc. INSTALLING THE 821 ETHERNET EXTENDER The Enable-IT 821 Ethernet Extenders

More information

Logitech Alert 700i/750i System Requirements & Support Guide

Logitech Alert 700i/750i System Requirements & Support Guide Logitech Alert 700i/750i System Requirements & Support Guide Contents System Requirements............................ 3 Product Information............................ 4 Contact Us..................................

More information

Agilent Technologies E5339A 38-Pin Low-Voltage Probe

Agilent Technologies E5339A 38-Pin Low-Voltage Probe Agilent Technologies E5339A 38-Pin Low-Voltage Probe Installation Note The 38-pin low-voltage probe provides a convenient way to connect two Agilent Technologies logic analyzer probe cables to a small

More information

THERM-O-FLOW EC-20/40 Timer

THERM-O-FLOW EC-20/40 Timer Instructions THERM-O-FLOW EC-20/40 Timer 310814B EN For use with THERM-O-FLOW Hot Melt Tanks. Model 118051 EC-20 two event timer for 115 VAC and 230 VAC Model 118052 EC-40 four event timer for 115 VAC

More information

CM68 4 Channel NTSC/PAL Video Decoder

CM68 4 Channel NTSC/PAL Video Decoder CM68 4 Channel NTSC/PAL Video Decoder Technical Reference Guide PCB Rev 1.0 www.soc-robotics.com Copyright 2009. SOC Robotics, Inc. 1 Manual Rev 0.90 Warranty Statement SOC Robotics warrants that the Product

More information

EQUIPMENT OPERATION MANUAL. Cartesian 200, 300, 400 and 500 Series. Setup. For Qualified Installer ONLY

EQUIPMENT OPERATION MANUAL. Cartesian 200, 300, 400 and 500 Series. Setup. For Qualified Installer ONLY EQUIPMENT OPERATION MANUAL Cartesian 200, 300, 400 and 500 Series For Qualified Installer ONLY Thank you for purchasing a Loctite Robot. *Read this manual thoroughly in order to properly use this robot.

More information

4300 WINDFERN RD #100 - HOUSTON TX VOICE (713) FAX (713) web: IMPORTANT!!!

4300 WINDFERN RD #100 - HOUSTON TX VOICE (713) FAX (713) web:   IMPORTANT!!! 4300 WINDFERN RD #100 - HOUSTON TX 77041-8943 VOICE (713) 973-6905 - FAX (713) 973-9352 web: www.twrlighting.com IMPORTANT!!! PLEASE TAKE THE TIME TO FILL OUT THIS FORM COMPLETELY. FILE IT IN A SAFE PLACE.

More information

HDMI Extender over Cat5e/6

HDMI Extender over Cat5e/6 Statement Thanks for purchasing this product, please read this user manual carefully before using this product.in the constant effort to improve our product, we reserve the right to make functions or parameters

More information

iq 16 Sync Charge Box

iq 16 Sync Charge Box USER INSTRUCTIONS iq 16 Sync Charge Box (iq 16 SCB Sync Station ) www.lockncharge.com iq 16 Sync Charge Box Contents Overview...1 Specifications...1 Safety instructions...2 Set up...2 How to charge multiple

More information

Loctite CL10 Quad LED Controller Part Number EQUIPMENT Operation Manual

Loctite CL10 Quad LED Controller Part Number EQUIPMENT Operation Manual Loctite CL10 Quad LED Controller Part Number 1514634 EQUIPMENT Operation Manual Contents 1 CAUTION 4 1.1 SAFETY INSTRUCTION 5 1.2 OUT OF BOX INSPECTION 5 1.3 PACKING LIST 6 2 OVERVIEW 6 3 TECHNICAL DATA

More information

IRB-RET O P E R A T I N G I N S T R U C T I O N S UNIVERSAL SAFETY RETROREFLECTIVE PHOTOEYE U L MONITORED DEVICE

IRB-RET O P E R A T I N G I N S T R U C T I O N S UNIVERSAL SAFETY RETROREFLECTIVE PHOTOEYE U L MONITORED DEVICE O P E R A T I N G I N S T R U C T I O N S IRB-RET UNIVERSAL SAFETY RETROREFLECTIVE PHOTOEYE U L 3 2 5-2 0 1 6 MONITORED DEVICE 4564 Johnston Parkway, Cleveland, Ohio 44128 P. 800 426 9912 F. 216 518 9884

More information

Zonit μats TM Users Guide μats1-lv Version 1.2

Zonit μats TM Users Guide μats1-lv Version 1.2 Zonit μats TM Users Guide μats1-lv Version 1.2 Table of Contents Product Overview...2 Pre-Installation Considerations...2 Product Features...3 Installation...4 Optional Accessories...4 μats TM Operational

More information

R & D SPECIALTIES SERIES 100 RO CONTROLLER USERS MANUAL. 2004, by R & D Specialties, Inc. All Rights Reserved.

R & D SPECIALTIES SERIES 100 RO CONTROLLER USERS MANUAL. 2004, by R & D Specialties, Inc. All Rights Reserved. R & D SPECIALTIES 2004, by R & D Specialties, Inc. All Rights Reserved. No part of this document may be copied or reproduced in any form or by any means without the prior written permission of R & D Specialties.

More information

Maintenance station. For DePuy Synthes Power Tools Electric Pen Drive and Air Pen Drive Systems. instructions for use

Maintenance station. For DePuy Synthes Power Tools Electric Pen Drive and Air Pen Drive Systems. instructions for use Maintenance station For DePuy Synthes Power Tools Electric Pen Drive and Air Pen Drive Systems instructions for use Table of Contents introduction 2 operating instructions 3 Care and Maintenance 6 Troubleshooting

More information

MPF-1, Mains Power Filter User Manual

MPF-1, Mains Power Filter User Manual 1/7 Important Safety Information 2/7 Protect the power cable from being walked on or pinched particularly at the plugs, convenience receptacles, and at the point where they exit from the apparatus. Refer

More information

USB-A to Serial Cable

USB-A to Serial Cable 26-949 User s Guide 6-Foot (1.82m) USB-A to Serial Cable Please read this user s guide before using your new cable. 2/2 Package contents USB-A to Serial Cable User s Guide Driver CD Quick Start Features

More information

FNet Repeater Installation & Operator s Instruction Manual

FNet Repeater Installation & Operator s Instruction Manual FNet Repeater Installation & Operator s Instruction Manual October 2004 CTB Inc. Warranty FNet Repeater CTB Inc. Warranty CTB Inc. warrants each new Chore-Tronics product manufactured by it to be free

More information

CM Mpixel CMOS Imaging Camera

CM Mpixel CMOS Imaging Camera CM130 1.3Mpixel CMOS Imaging Camera Technical Reference Guide PCB Rev 1.0 www.soc-robotics.com Copyright 2009. SOC Robotics, Inc. 1 Manual Rev 0.90 Warranty Statement SOC Robotics warrants that the Product

More information

IRB-RET O P E R A T I N G I N S T R U C T I O N S UNIVERSAL SAFETY RETROREFLECTIVE PHOTOEYE U L M O N I T O R E D DEVICE

IRB-RET O P E R A T I N G I N S T R U C T I O N S UNIVERSAL SAFETY RETROREFLECTIVE PHOTOEYE U L M O N I T O R E D DEVICE O P E R A T I N G I N S T R U C T I O N S IRB-RET UNIVERSAL SAFETY RETROREFLECTIVE PHOTOEYE U L 3 2 5-2 0 1 6 M O N I T O R E D DEVICE 4564 Johnston Parkway, Cleveland, Ohio 44128 P. 800 426 9912 F. 216

More information

MWC-8. Operation MWC-8 800MHz Controller Manual. Operation Manual. manmwc9.

MWC-8. Operation MWC-8 800MHz Controller Manual. Operation Manual. manmwc9. MWC-8 Operation MWC-8 800MHz Controller Manual Operation Manual manmwc9 www.myeclubtv.com 1 CONTENTS Specifications. 3 Controller Orientation (Front / Rear) 4 Keypad Key Identification. 5 Main Features

More information

MPP1700 User s Manual

MPP1700 User s Manual 2011 Visionary Solutions, Inc. All rights reserved. Please visit the support section of our website at www.vsicam.com for manuals, other documentation, and software downloads. Visionary Solutions, Inc.

More information

MCOR CRATE. OPERATIONS MANUAL Model Preliminary Midtown PL NE Suite A Albuquerque NM bira.com

MCOR CRATE. OPERATIONS MANUAL Model Preliminary Midtown PL NE Suite A Albuquerque NM bira.com MCOR CRATE OPERATIONS MANUAL Model 2513 Preliminary 2410 Midtown PL NE Suite A Albuquerque NM 87107 bira.com info@bira.com 505-881-8887 TABLE OF CONTENTS 1.0 Introduction 1.1 MCOR Crate Physical Description

More information

PRODUCT CONTENTS... 3 II. REQUIRED MATERIALS... 3 III. OVERVIEW... 3 IV. BENCH LAYOUT...

PRODUCT CONTENTS... 3 II. REQUIRED MATERIALS... 3 III. OVERVIEW... 3 IV. BENCH LAYOUT... IR-510 Bench 2012 Infrared Industries, Inc. 25590 Seaboard Lane Hayward, CA 94545 Toll-free phone 800.344.0321 Phone 510.782.8100 Fax 510.782.8101 www.infraredindustries.com Table of Contents I. PRODUCT

More information

INSTALLATION AND USER GUIDE 2800MWB SINGLE LINE BASIC FEATURE TELEPHONE

INSTALLATION AND USER GUIDE 2800MWB SINGLE LINE BASIC FEATURE TELEPHONE INSTALLATION AND USER GUIDE 2800MWB SINGLE LINE BASIC FEATURE TELEPHONE TeleMatrix Copyright 2005 COMPLIANCE AND SAFETY As specified by FCC regulation, we are required to inform you of specific governmental

More information

QPP Proprietary Profile Guide

QPP Proprietary Profile Guide Rev. 04 April 2018 Application note Document information Info Content Keywords Proprietary Profile, Server, Client Abstract The Proprietary Profile is used to transfer the raw data between BLE devices.

More information

DISCONTINUED PRODUCT DISCONTINUED PRODUCT

DISCONTINUED PRODUCT DISCONTINUED PRODUCT Important Safety Instructions This manual contains important safety instructions that should be followed during the installation and maintenance of this product. Please read this manual thoroughly before

More information

DIGITAL VOLTAGE INDICATOR

DIGITAL VOLTAGE INDICATOR DIGITAL VOLTAGE INDICATOR Instruction Manual US Patent 6,998,832 HD ELECTRIC COMPANY 1475 LAKESIDE DRIVE WAUKEGAN, ILLINOIS 60085 U.S.A. PHONE 847.473.4980 FAX 847.473.4981 website: www.hdelectriccompany.com

More information

Owner's Manual. For latest instructions please go to

Owner's Manual. For latest instructions please go to mycharge name and logo are registered trademarks of RFA Brands. 2012-2013 RFA Brands. All Rights Reserved. Patent Pending. Made in China. IB-MYC05001RM Owner's Manual For latest instructions please go

More information

1X2 HDMI Splitter with 3D Support

1X2 HDMI Splitter with 3D Support AV Connectivity, Distribution And Beyond... VIDEO WALLS VIDEO PROCESSORS VIDEO MATRIX SWITCHES EXTENDERS SPLITTERS WIRELESS CABLES & ACCESSORIES 1X2 HDMI Splitter with 3D Support Model #: SPLIT-HDM3D-2

More information

Lotus DX. sit-stand workstation. assembly and operation instructions. MODEL # s: LOTUS-DX-BLK LOTUS-DX-WHT

Lotus DX. sit-stand workstation. assembly and operation instructions. MODEL # s: LOTUS-DX-BLK LOTUS-DX-WHT Lotus DX assembly and operation instructions sit-stand workstation MODEL # s: LOTUS-DX-BLK LOTUS-DX-WHT safety warnings 13.6 Kg 30 lbs. 2.2 Kg 5 lbs. safety instructions/warning Read and follow all instructions

More information

DX-C USER GUIDE

DX-C USER GUIDE PC/Mac USB File Transfer Adapter DX-C114200 USER GUIDE 2 3 Dynex DX-C114200 PC/Mac USB File Transfer Adapter Contents Important safety instructions...3 Introduction...4 Features...5 Package Contents...5

More information

AC4G-D User s Manual

AC4G-D User s Manual AC4G-D User s Manual Entire contents of this manual 2004 Active Cool Ltd. Ashkelon, Israel. Reproduction in whole or in part without permission is prohibited. Active Cool and AC4G-D are registered of Active

More information

TD 600 Thermo-Fastprinter

TD 600 Thermo-Fastprinter Thermo-Fastprinter Content 1. Specification... 2 2. Operating elements... 2 3. Setup... 3 4. Operating... 4 5. Maintenace, Cleaning... 5 6. Declaration of conformity... 6 7. Warranty and Service... 7 05.24.05

More information

IMS-9000 Intelligent Modem Switch USER S MANUAL. Document Part #: RDC-HDWIMS9K100

IMS-9000 Intelligent Modem Switch USER S MANUAL. Document Part #: RDC-HDWIMS9K100 IMS-9000 Intelligent Modem Switch USER S MANUAL Document Part #: RDC-HDWIMS9K100 2000 Delphi Display Systems, INC. All rights reserved. Delphi Display Systems, INC. (Delphi) reserves the right to revise

More information

Instructions. TLA5Fxxx, TLA6Fxx, & TLA7Fxx PowerFlex Field Upgrade Kits for TLA5000, TLA600, and TLA700 Logic Analyzers

Instructions. TLA5Fxxx, TLA6Fxx, & TLA7Fxx PowerFlex Field Upgrade Kits for TLA5000, TLA600, and TLA700 Logic Analyzers Instructions TLA5Fxxx, TLA6Fxx, & TLA7Fxx PowerFlex Field Upgrade Kits for TLA5000, TLA600, and TLA700 Logic Analyzers 071-0591-05 This document applies to TLA System Softwareversion 3.2 and above. www.tektronix.com

More information

FA-2448 SIX POSITION Filter Wheel

FA-2448 SIX POSITION Filter Wheel 15 Discovery Way, Acton, MA 01720 Phone: (978)263-3584, Fax: (978)263-5086 Web Site: www.acton-research.com Operating Instructions Acton Research Corporation FA-2448 SIX POSITION Filter Wheel Rev. 3.05.17

More information

Broadband Automatic Disconnect Switch. User Manual

Broadband Automatic Disconnect Switch. User Manual Reset/Test Primary/ Primary Broadband Automatic Disconnect Switch User Manual Local Power Remote Pwer Local 63V Fault Secondary Select Secondary 220V Normal 990-1929 09/2004 Introduction Introduction

More information

USB Server User Manual

USB Server User Manual 1 Copyright Notice Copyright Incorporated 2009. All rights reserved. Disclaimer Incorporated shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential

More information

Chroma-Q Magic Box EthernetSwitch 7

Chroma-Q Magic Box EthernetSwitch 7 Chroma-Q Magic Box EthernetSwitch 7 User Manual Version 1.3 June 2016 PN: 156-0500 Warranty Statement Chroma-Q warrants to the original purchaser, with proof of purchase, that its delivered products shall

More information

7191AD User Manual. June Daisy Data Displays, Inc Lewisberry Road, York Haven, PA Phone:

7191AD User Manual. June Daisy Data Displays, Inc Lewisberry Road, York Haven, PA Phone: June 2017 Daisy Data Displays, Inc. 2850 Lewisberry Road, York Haven, PA 17370 Phone: 717.932.9999 DISCLAIMER Daisy Data Displays, Inc. makes no representations or warranties with respect to the contents

More information

Proliphix EPA-60 Installation Guide

Proliphix EPA-60 Installation Guide Proliphix EPA-60 Installation Guide Rev 1.2 Page 2 of 5 Installation CAUTION THE EPA-60 SHOULD ONLY BE POWERED WITH THE PROLIPHIX POWER SUPPLY INCLUDED WITH THE EPA-60. DO NOT POWER THE EPA-60 WITH ANY

More information

SAVE THESE INSTRUCTIONS

SAVE THESE INSTRUCTIONS and Height Mounts Assembly, Installation and Operating Instructions Model Nos. QL, QLA, ARM250, QLM6 and QLAM6 NOTE: Check all parts for shipping damage. In case of shipping damage, DO NOT use. Contact

More information

Installation and Operation Guide for PD5200 and PD5300 Automatic Transfer Switch

Installation and Operation Guide for PD5200 and PD5300 Automatic Transfer Switch Installation and Operation Guide for PD5200 and PD5300 Automatic Transfer Switch PD52 PD52S & PD52DCS PD53-100 te: The PD52S & PD52DCS are provided with LED lights. The GREEN LIGHTS indicate Shore Power

More information

ATX 450 and ATX 550 Watt Power Supplies

ATX 450 and ATX 550 Watt Power Supplies USER GUIDE ATX 450 and ATX 550 Watt Power Supplies NS-PCW4508/NS-PCW4508-C/NS-PCW5508/NS-PCW5508-C Before using your new product, please read these instructions to prevent any damage. Contents Introduction......................................................3

More information

VELOCICALC Air Velocity Meter

VELOCICALC Air Velocity Meter ENERGY AND COMFORT Ventilation Testing VELOCICALC Air Velocity Meter Model 9525 Operation and Service Manual Copyright TSI Incorporated / May 2007 / All rights reserved. Address TSI Incorporated / 500

More information

TRF-ZW1 Z-Wave Extender. Owner s Manual

TRF-ZW1 Z-Wave Extender. Owner s Manual TRF-ZW1 Z-Wave Extender Owner s Manual TRF-ZW1 Z-Wave Extender Owner's Manual 2014 Universal Remote Control, Inc. The information in this Owner s Manual is copyright protected. No part of this manual may

More information

TC1880 Series. 4/5/6/8 Channel RS-232 FIBER OPTIC MICRO MUX User's Manual

TC1880 Series. 4/5/6/8 Channel RS-232 FIBER OPTIC MICRO MUX User's Manual Series 4/5/6/8 Channel RS-232 FIBER OPTIC MICRO MUX MODEL: S/N: DATE: Notice! Although every effort has been made to insure that this manual is current and accurate as of date of publication, no guarantee

More information

Illuminate 25 Light Starter Kit What s included Light String Control Box Spare Fuses Safety Instructions Quick Start Guide

Illuminate 25 Light Starter Kit What s included Light String Control Box Spare Fuses Safety Instructions Quick Start Guide Illuminate Password: 12345678 QR Codes to download App: IOS/Apple Android Quick Start Guide Illuminate 25 Light Starter Kit What s included Light String Control Box Spare Fuses Safety Instructions Quick

More information

Pulse LED Instruction Guide

Pulse LED Instruction Guide PARTS LIST Light Fixture Aquarium Frame Mounts Instruction Guide WARNING: To guard against injury, basic precautions should be observed, including the following: A) READ AND FOLLOW ALL SAFETY INSTRUCTIONS.

More information