PRIMERGY RX900 S2. System configurator and order-information guide August PRIMERGY Server. Contents

Transcription

1 PRIMERGY RX900 S2 System configurator and order-information guide August 2014 Contents Instructions Configuration diagram Configurator 0 0 System software 1 I Basic unit 2 II Processor 3 III Memory 4 IV USB devices / optical devices 5 V Hard disk drives 7 VI Internal SAS RAID Controller 8 VII External SCSI / SAS controller 9 VIII Fibre Channel controller 10 IX Communication / Network / CNA / Infiniband 11 X irmc S2 advanced pack / TPM 12 XII Optional PSU / Power Cord Change report PRIMERGY Server

2 PRIMERGY RX900 S2 Status Instructions This document contains basic product and configuration information that will enable you to configure your system via PC-/System-Architect Only these tools will ensure a fast and proper configuration of your PRIMERGY server or your complete PRIMERGY Rack system. You can configure your individual PRIMERGY server in order to adjust your specific requirements. The System configurator is divided into several chapters that are identical to the current price list and PC-/System-Architect. Please follow the lines. If there is a junction, you can choose which way or component you would like to take. Go through the configurator by following the lines from the top to the bottom. Section III Memory, example There are X memory slots which can be equipped with XXX MB It is permissible to make up to X passes through the memory upgrade options X times S26361-XXX-XXX Memory XXX MB S26361-XXX-XXX Memory XXX MB max. X times per system max. X times per system In one chapter you can only select as many components (here 4x) as the arrow indicates. 4x Please note that there are information symbols which indicate necessary information. Further information in the internet see: (internet) (extranet) Prices and availability see price list and PC-/System-Architect. Subject to change and errors excepted. Fujitsu PRIMERGY Server 2 of 18

3 Slot #17 PCIe 2.0 x4, short lengh Slot #16 PCIe 2.0 x8, short lengh Slot #15 PCIe 2.0 x8, short lengh Slot #14 PCIe 2.0 x8, short lengh Slot #13 PCIe 2.0 x8, short lengh Slot #12 PCIe 2.0 x8, short lengh PHP Slot #9 PCIe 2.0 x8, short lengh PHP Slot #8 PCIe 2.0 x8, internal RAID Video COM USB #4 REAR VIEW Slot #11 PCIe 2.0 x8, short lengh PHP Slot #10 PCIe 2.0 x8, short lengh PHP USB #1 USB #2 USB #3 FRONT VIEW TOP VIEW Slot #17 PCIe 2.0 x4, short lenght Slot #16 PCIe 2.0 x8, short lenght Slot #15 PCIe 2.0 x8, short lenght Slot #14 PCIe 2.0 x8, short lenght Slot #13 PCIe 2.0 x8, short lenght Slot #12 PCIe 2.0 x8, short lenght PHP Slot #11 PCIe 2.0 x8, short lenght PHP Slot #10 PCIe 2.0 x8, short lenght PHP Slot #9 PCIe 2.0 x8, short lenght PHP Slot #8 PCIe 2.0 x8, internal Raid slot CPUMEMR #8 with 1x CPU socket and 16x DIMM slots CPUMEMR #7 with 1x CPU socket and 16x DIMM slots CPUMEMR #6 with 1x CPU socket and 16x DIMM slots CPUMEMR #5 with 1x CPU socket and 16x DIMM slots CPUMEMR #4 with 1x CPU socket and 16x DIMM slots CPUMEMR #3 with 1x CPU socket and 16x DIMM slots CPUMEMR #2 with 1x CPU socket and 16x DIMM slots CPUMEMR #1 with 1x CPU socket and 16x DIMM slots Configuration diagram PRIMERGY RX900 S2 Basic Unit ( I ) Processor ( II ) Memory ( III ) System configurator and order-information guide PRIMERGY RX900 S2 Status Extension slots: external SCSI / RAID controller ( VIII ), Fiber Channel ( IX ), Communication/Network ( X ) DVD / Blue Ray Operating Panel Local View LCD Display USB #7 2.5" SAS #1 2.5" SAS #3 USB #6 2.5" SAS #5 2.5" SAS #7 2.5" SAS #0 2.5" SAS #2 Video USB #5 2.5" SAS #4 2.5" SAS #6 Hard disk drives ( VI ) Hard disk drives ( VI ) Slot #7 PCIe 2.0 x8, short length Slot #6 PCIe 2.0 x8, short length Slot #5 PCIe 2.0 x4, short length Slot #4 PCIe 2.0 x8, short length Slot #3 PCIe 2.0 x8, short length Slot #2 PCIe 2.0 x8, short length Slot #1 PCIe 2.0 x8, short length 10 Gb Ether 8 Ether 2 Ether 4 Ether 6 Service Ether 1 Ether 3 Ether 5 10 Gb Ether 7 1. PSU 2. PSU 3. PSU ( 2+1 ) 4. PSU ( 2+2 ) Hot Plug Redundant Power Supply (XII) Included in the base configuration Option Fujitsu PRIMERGY Server 3 of 18

4 PRIMERGY-Software Configurators and Release Lists Start "PRIMERGY RX900 S2" PRIMERGY RX900 S2 Status Section O SW Configurator 64 bit (EM64T / IA64) with OEM-Software for PRIMERGY Server without OEM-Software for PRIMERGY Server For all SW products please refer to the corresponding software configurator accessible via the Extranet under "Configuration & Tools, -All configurations, -Software, URL see below. OEM- SW is bound to HW and is not allowed to be ordered separately. Exceptions: VMware SW, Citrix XenServer VMware-Software - VirtualCenter Management Server for any server released for Windows Server Virtual Infrastructure 3 for PRIMERGY > except all mono PRIMERGY systems - ESX2 for PRIMERGY RX/TX300S2, RX/TX600S3, BX620S2, BX630 Dual/Quad, BX630 8-way Microsoft Hyper-V Server and System Center - Microsoft System Center Virtual Machine Manager Workgroup Edition for any server released for Windows Server 2008 R2 - Microsoft System Center Essentials Management Suite for any server released for Windows Server 2008 SP2 - Microsoft Hyper-V Server 2008 R2 Microsoft - Windows Server 2008 R2 Server Licenses Linux - Software *) **) - Windows Server 2008 R2 Datacenter # Open Enterprise Server ***) - Windows Server 2008 R2 Enterprise only - SuSE Linux ES (OEM): LO - EM64T - Red Hat EL (OEM): LO Microsoft - Windows Server 2008 Server Licenses - Windows Server 2008 Datacenter PRIMECLUSTER *) - Windows Server 2008 Enterprise - Clustering - - Load Balancing only MultiPath, Duplex Data EM64T Manager (DDM) Windows, Linux (W-DDM) Details eg. version numbers are published on the page referred to Manageability Software: V**) *) Pay attention to the PRIMECLUSTER release and ordering information in the Extranet under - irmc advanced Pack only - RemoteView Software EM64T - RemoteView Service Board **) Pay attention to release and order information in PRINCE -> Operating System - RemoteView Diagnosis - RemoteDeploy ***) Supply over distribution or procurement from FSC VP BC Software You'll find single software configurators and release lists (OS-matrix / system management / security) under following addresses: Continue with PRIMERGY HW configurator for internal users: for partners: Fujitsu PRIMERGY Server 4 of 18

5 Start PRIMERGY RX900 S2 PRIMERGY RX900 S2 Status Section I Basic unit PRIMERGY RX900 S2 Baseboard with - Intel E chipset with serial QPI links (Quick Path Interconnect) Rack unit 8U with - 16 PCI-Express Slots - 2 hot-plug power supplys (additional PSU as option) 2x PCIe 2.0 x4 (half length) - 4 CPUMemory Boards (CPUMEMR) (up to 4 additional boards optional) 14x PCIe 2.0 x8 (half length) - LCD-Display for LocalView (Service Display) - 8x socket for CPUMEMR - 8 bays for 2.5" SAS/SATA HDD`s - SATA controller on-board (for ODD) - Power cord for rackmounting (ICE 320 C14->C19 plug) - irmc S2 (integrated Remote Management Controller) - no Rack- mounting kit included with graphics controller and 10/100Mbit Service LAN-port - 6x 1GBit LAN Ports on-board (WOL-capable) Base Unit S26361-K1403-V800-2x 10GBit LAN Ports on-board - SAS RAID controller as option - ServerView Suite Software package incl. ServerStart, ServerBooks, Management Software and Updates Interfaces: Front side - 3x USB 2.0-1x VGA (15 pin) Rear Side S26361-F2735-E111 S26361-F2735-E109-2x USB 2.0 No Rackmount-Kit option RMK RX900-1x VGA (15 pin) Only for loose deliveries telescopic rails - 1x RS-232-C (serial, 9 pin) No mounting in Racks possible - 6x onboardlan RJ45, 2x onboardlan SFP+, 1x ServiceLAN RJ45 max. 1x per system consisting of Internal - 1 pair of telescopic rails - 1x internal USB Interfaces for backup device with screws and washers - 1x internal port for UFM (ussd) Module (Embedded vsphere ESXi 4.0) 1x per system S26361-F4530-E10 no PS/2 connection for KB / Mouse (USB must be used instead) S26361-F2735-L109 RMK RX900 for Server Drop-in telescopic rails S26361-F4530-E13 Mounting of RMK in symmetrical for loose delivery Bracket 3U in asymmetrical racks max. 1x per system racks (no support brackets needed) max. 1x per system S26361-F2735-L7 Lateral cable management for RX900 S26361-F2735-E17 S26361-F2201-E20 mounted in asymmetrical racks Cable management for RX900 2U cable arm behind systems for loose delivery - for asym. PRIMECENTER racks - for symmetrical PCR M1 - not for 3rd party - or for 3rd party racks S26361-F2201-L20 max. 4x per system max. 3x per system 2U cable arm mounted behind systems in symmetrical PCR M1 or 3rd party racks for loose delivery PRIMECENTER S2 or M1 Racks SNP:SY-F1647E301-P Installation ex works for one server or subsystem. Hereby the rack will be delivered completely pre-mounted and all wired connections are tested. With racks 12U, 24U, 38U: Systems and components will be delivered installed in the rack With racks 46U: Systems and components will be delivered separately To be ordered only together with a PRIMERGY PRIMECENTER rack e.g.: S26361-K826-V10x refer configurator PC-Rack max. 1x per System S26361-F2735-L31 Support Bracket 3 HU for mounting in asymmetrical racks 1x per system "Rack-mounting ex factory" This service is to be ordered once per installable server/storage subsystem, in order to get the server/storage subsystem mounted into the PRIMERGY racks. In case of the 46 U PRIMERGY Rack, this service has to be ordered, to get the mounting kits and the cables installed. A Fujitsu PRIMERGY Server 5 of 18

6 A PRIMERGY RX900 S2 Status Section II Processor 4 CPU Memory Riser (CPUMEMR) and 4 CPU's must be configured as minimum, as maxmimum 8 are possible. Later upgrading to a 6 or 8 processor system is also possible, but requires possibly adding of PSU modules. Extension CPUs must be identical to the already installed CPU s. 4 CPU Memory Riser (CPUMEMR) are part of the Base Unit S26361-K1403-V800 S26361-D3145-A100 CPUMEMR - CPU Memory Riser Board A minimum of 4 CPUMEMR must be configured - 1x CPU Socket for Intel Xeon processor E series incl. passive heat sink - 16 Memory DIMM Slots for DDR3 DIMM - 4x SMI on each CPUMEMR Max 8 CPUMEMR per System Following CPU s can be configured A minimum of 4 CPU s must be configured Xeon E C/20T 2.40GHz 30MB 6.4GT/s (130W) S26361-F4471-E887 4x Xeon E C/20T 2.26GHz 24MB 6.4GT/s (130W) S26361-F4471-E886 Xeon E C/20T 2.00GHz 24MB 6.4GT/s (130W) S26361-F4471-E885 Xeon E C/16T 2.13GHz 24MB 6.4GT/s (105W) S26361-F4471-E883 Xeon E C/8T 2.67GHz 24MB 6.4GT/s (130W) S26361-F4471-E837 B Fujitsu PRIMERGY Server 6 of 18

7 B PRIMERGY RX900 S2 Status Section III Memory Memory configuration modes Memory DIMM population Order Interleaving Mode In RX900 S2 Memory Interleaving Mode is default and set by BIOS. Hemisphere Mode RX900 S2 supports Hemisphere Mode from 5-8 CPU configuration default and set by BIOS up to 4 CPU configuration support non Hemisphere Mode only. Spare Mode Spare mode is not supported in RX900 S2 Mirroring mode To use Mirroring Mode you have to order the Mirroring Mode option - S26361-F4472-E3 In mirroring mode, all data are copied within the main memory. Therefore only 50 % of the total memory is available for the operating system. Two types of mirroring modes are available: Intrasocket Mirroring - Memory Mirroring within CPUMEMR Memory will be mirrored from one memory controller to the other memory controller within the same CPU. Intrasocket Mirroring is possible for all CPU up to 4 CPUs. When enabling Memory Mirroring in case of 4 socket configuration, same DIMMs must be populated between DDR channel (ABCD) and (EFGH). Memory Mirroring is configured within CPUMEMR. This means same size of DIMMs must be populated as below - DIMM# (1B, 1D, 1F, 1H) should be same size of DIMMs. - DIMM# (1A, 1C, 1E, 1G) should be same size of DIMMs. - DIMM# (2B, 2D, 2F, 2H) should be same size of DIMMs. - DIMM# (2A, 2C, 2E, 2G) should be same size of DIMMs. Intersocket Mirroring - Memory Mirroring between CPUMEMR Memory will be mirrored from one memory controller to an memory controller on another CPU. Intersocket mirroring is only possible with 6 or 8 CPUs. When enabling Memory Mirroring in case of 6 or 8 socket configuration, all four DIMMs must be same size within CPUMEMR. - DIMM# (1B, 1D, 1F, 1H) should be same size of DIMMs. - DIMM# (1A, 1C, 1E, 1G) should be same size of DIMMs. - DIMM# (2B, 2D, 2F, 2H) should be same size of DIMMs. - DIMM# (2A, 2C, 2E, 2G) should be same size of DIMMs. In addition to this, same configuration must be kept between CPUMEMR (1,2), (3,4), (5,6), (7,8) because Memory mirroring will be configured between CPUMEMRs. Memory Mirror for up to 4-S (Intra-Socket Mirroring) Memory Mirror for 6-S and 8-S (Inter-Socket Mirroring) C Fujitsu PRIMERGY Server 7 of 18

8 C PRIMERGY RX900 S2 Status Max. Capacity / Features The system can be equipped with up to128 DIMMs (distributed on 8 CPUMEMRiser boards) Each DIMM slot can optionally be equipped with 4GB, 8GB, 16GB or 32GB DDR3 DIMM modules, so the maximal memory size is 4096GB with 32GB modules. ECC with SDDC (Chipkill) is standard for RX900 S2. Max. Memory Speed depends on CPU QPI Speed, but is limited to 1066 MHz. S26361-F4472-E3 Mirrored Mode Installation BIOS setup for Mirrored mode Preinstallation ex factory max. 1x per system on special release as long as available as soon as available S26361-F4523-E942 S26361-F4523-E943 S26361-F4523-E944 S26361-F4523-E945 S26361-F4523-E946 S26361-F4523-E947 Memory 16GB Memory 32GB Memory 32GB Memory 64GB Memory 128GB Memory 64GB min. LV RDIMM (single rank) LV RDIMM (dual rank) LV RDIMM (quad rank) LV RDIMM (quad rank) LV RDIMM (quad rank) LV RDIMM (dual rank) 2x consisting of consisting of consisting of consisting of consisting of consisting of mem 4x 4GB modules 4x 8GB modules 4x 8GB modules 4x 16GB modules 4x 32GB modules 4x 16GB modules (4Gb) upgr. occupies 4 memory slots occupies 4 memory slots occupies 4 memory slots occupies 4 memory slots occupies 4 memory slots occupies 4 memory slots max. 32x per system max. 32x per system max. 32x per system max. 32x per system max. 32x per system max. 16x per system on special release as long as available as soon as available S26361-F4523-E942 S26361-F4523-E943 S26361-F4523-E944 S26361-F4523-E945 S26361-F4523-E946 S26361-F4523-E947 Memory 16GB Memory 32GB Memory 32GB Memory 64GB Memory 128GB Memory 64GB up to 314x LV RDIMM (single rank) LV RDIMM (dual rank) LV RDIMM (quad rank) LV RDIMM (quad rank) LV RDIMM (quad rank) LV RDIMM (dual rank) memory consisting of consisting of consisting of consisting of consisting of consisting of upgrades 4x 4GB modules 4x 8GB modules 4x 8GB modules 4x 16GB modules 4x 32GB modules 4x 16GB modules (4Gb) occupies 4 memory slots occupies 4 memory slots occupies 4 memory slots occupies 4 memory slots occupies 4 memory slots occupies 4 memory slots max. 32x per system max. 32x per system max. 32x per system max. 32x per system max. 32x per system max. 16x per system S26361-F4524-E100 Upgrade path is CPUMEMR - CPU Memory Riser Board - 2x CPUMEMR and 2 CPUs A minimum of 4 CPUMEMR must be configured for CPUMEMR slot 5 and 6 2 or 4x - 1x CPU Socket for Intel Xeon processor E series - 4x CPUMER and 4 CPUs incl. passive heat sink for CPUMEMR slot 5 to 8-16 Memory DIMM Slots for DDR3 DIMM Other CPUMEMR upgrades max. 4 CPUMEMR per System are not supported! One of the following CPU s must be configured per CPU Memory Riser Board Xeon E C/20T 2.40GHz 30MB 6.4GT/s (130W) S26361-F4471-E887 2 or 4x Xeon E C/20T 2.26GHz 24MB 6.4GT/s (130W) S26361-F4471-E886 Xeon E C/20T 2.00GHz 24MB 6.4GT/s (130W) S26361-F4471-E885 Xeon E C/16T 2.13GHz 24MB 6.4GT/s (105W) S26361-F4471-E883 Xeon E C/8T 2.67GHz 24MB 6.4GT/s (130W) S26361-F4471-E837 on special release as long as available as soon as available S26361-F4523-E942 S26361-F4523-E943 S26361-F4523-E944 S26361-F4523-E945 S26361-F4523-E946 S26361-F4523-E647 Memory 16GB Memory 32GB Memory 32GB Memory 64GB Memory 128GB Memory 64GB LV RDIMM (single rank) LV RDIMM (dual rank) LV RDIMM (quad rank) LV RDIMM (quad rank) LV RDIMM (quad rank) LV RDIMM (dual rank) up to 16x consisting of consisting of consisting of consisting of consisting of consisting of memory 4x 4GB modules 4x 8GB modules 4x 8GB modules 4x 16GB modules 4x 32GB modules 4x 16GB modules (4Gb) upgrades occupies 4 memory slots occupies 4 memory slots occupies 4 memory slots occupies 4 memory slots occupies 4 memory slots occupies 4 memory slots max. 32x per system max. 32x per system max. 32x per system max. 32x per system max. 32x per system max. 16x per system D Fujitsu PRIMERGY Server 8 of 18

9 D PRIMERGY RX900 S2 Status Section IV USB devices / optical devices Setup RX900 S2 by SV Installation Manager is supported with following configurations: built in CD/DVD or USB CD/DVD, no Floppy disk drive: UNC Network share reachable DVD Dummy - C26361-K644-C640-*-Y155 built in DVD slot if no DVD/Blue Ray is requested S26361-F3531-E2 S26361-F3269-E2 S26361-F3641-E2 Blu-ray Combo slim SATA DVD-RW supermulti slim SATA Blu-ray Triple Writer slim SATA 6x BD-ROM, 16x DVD, 40x CD all formats, DUAL/DL, DVD-RAM 6x BD-RW, 8x DVD, 24x CD 1x BD DL and all CD/DVD formats only W2K, W3K and Linux BD DL and all CD/DVD formats 0.5 x 5.25", black bezel 0.5 x 5.25", black bezel 0.5 x 5.25" max. 1x per system max. 1x per system max. 1x per system E Fujitsu PRIMERGY Server 9 of 18

10 E PRIMERGY RX900 S2 Status Section V Hard disk drives HDD SAS 6Gb/s 2.5" with hot plug/hot replace tray 300GB 10000rpm,<4,5ms, 16MB Cache S26361-F4482-E130 configuration of 450GB 10000rpm,<4,5ms, 16MB Cache S26361-F4482-E145 SAS-HDDs requires 600GB 10000rpm,<4,5ms, 16MB Cache S26361-F4482-E160 SAS RAID controller 900GB 10000rpm,<4,5ms, 32MB Cache S26361-F4482-E190 1,2TB 10000rpm,<4,5ms, 64MB Cache S26361-F5247-E112 as soon as available 146GB 15krpm,<4,5ms, 32MB Cache S26361-F4482-E GB 15krpm,<4,5ms, 32MB Cache S26361-F4482-E GB 7.2krpm,<9,5ms, 64MB Cache 1TB 7.2krpm,<9,5ms, 64MB Cache S26361-F5228-E500 S26361-F5228-E100 Solid State Disk, Mainstream Endurance* SSD SAS 6Gb/s MLC 2.5" with hot plug/hot replace tray 100GB, Enterprise Performance S26361-F4581-E100 as long as stock 200GB, Enterprise Performance S26361-F4581-E200 as long as stock max. 8x 400GB, Enterprise Performance S26361-F4581-E400 as long as stock SSD SAS 12Gb/s 2.5" with hot plug/hot replace tray as soon as available 200GB, Enterprise Performance S26361-F5297-E200 Interface SAS12Gb/s and SAS 6Gb/s. 400GB, Enterprise Performance S26361-F5297-E400 SAS 12Gb/s support is not released max. 8x 800GB, Enterprise Performance S26361-F5297-E TB, Enterprise Performance S26361-F5297-E160 *) SSD Mainstream Endurance 10DWPD over 5y SSD SAS 2.5" SLC as long as stock S26361-F4541-E100 SSD SAS 100GB, SLC Solid State Disk SAS 6Gb/s Enterprise Perfomance hot plug/hot replace tray as long as stock S26361-F4541-E400 SSD SAS 400GB, SLC Solid State Disk SAS 6Gb/s Enterprise Perfomance hot plug/hot replace tray Section VI PCIe-SSD S26361-F4522-E781 S26361-F4522-E121 loose delivery: S26361-F4522-L781/L121 PCIe-SSD 785GB MLC PCIe-SSD 1.2TB MLC iodrive2 785GB iodrive2 1.2TB max. 4x PCIe 2.0 PCIe nm Lithography 25nm Lithography PCIe x4, Low Profile PCIe x4, Low Profile max. 4x per system max. 4x per system F Fujitsu PRIMERGY Server 10 of 18

11 F PRIMERGY RX900 S2 Status Section VI internal SAS RAID 0/1 and RAID5 Controller for HDD s S26361-F3554-E512 RAID Ctrl SAS 6G 8port internal Based on chip LSISAS2108 LSI MegaRAID 512MB Cache with ECC 1x RAID 0, 1, 10, 5, 50, 6, 60 optional BBU Support for 3Gb/s and 6Gb/s SATA and SAS hard drives PCIe x4 Low-profile MD2 form factor max. 1x per system Modular RAID controller must be ordered, if at least one internal HDD is configured! S26361-F3257-E270 Cache Battery Backup Unit with 70cm cable set max. 2x per system BBU max. 2x per system possible for loose delivery please order S26361-F3257-L210 G Fujitsu PRIMERGY Server 11 of 18

12 G PRIMERGY RX900 S2 Status Section VII external SAS controller A. SAS controller for external backup drives The number of max. I/O PCIe controllers highly depends on the numer of CPUMEMR! The following Table describes the max. number of PCIe controller slots CPUMEMR PCIe slots PCIe slots (PHP) The showm max. numer of each controller is valid,as far as the numer of PCIe slots are available also. 0 4 S26361-F3271-E2 SAS Controller 3Gb/s 8 port LSI SAS3442E-R max. 3x PCIe x4, The 3Gb/s SAS Controller is basically for SX10 S2 int: 4 port due to the fact that SX10 S2 supports 3Gb/s only. ext: 4 port We have to withdraw the controller because it can't max. 3x per system run under UEFI BIOS. We will release the controller with UEFI support soon. Same controller but new order number! B. SAS controller for external backup drives max. 3x S26361-F3628-E1 SAS Controller 6Gb/s 8 port LSI SAS9200-8e PCIe ext: 8 port max. 3x per system C. SAS RAID controller for JBOD subsystems max. 2x S26361-F3593-E1 8 port SAS RAID Controller The RAID controller can be used only for the connection of LSI external subsystems (FibreCAT SX40, Eternus JX40) MegaRAID SAS9280-8e 6Gb/s 512MB Cache with ECC Cables for the connection from the RAID Controllers RAID 0, 1, 10, 5, 50, 6 & 60 to the subsystem see configurator FibreCAT SX40 without ibbu The usage of the internal SAS ports is not supported! SAS 6Gb/sec 8 port external PCIe x4, 167mm full height bracket max. 2x per system S26361-F3257-E270 Cache Battery Backup Unit with 70cm cable set max. 2x per system BBU max. 2x per system possible for loose delivery please order S26361-F3257-L210 2x as soon as available S26361-F3713-E3 RAID Ctrl SAS 6G 8port external LSI MegaRAID SAS e 1GB Cache with ECC RAID 0, 1, 5, 6, 10, 50 & 60 without FBU SAS 6Gb/sec 8 port external PCIe 3.0 x8, MD2 form factor full height bracket max. 2x per system S26361-F3669-E170 Flash Backup Unit with 70cm cable set max. 1x per Contr., 2x per system S26361-F3669-L110 Flash Backup Unit with 25cm, 55cm, 70cm cable set max. 1x per Contr., 2x per system as soon as available as soon as available S26361-F3669-E661 S26361-F3669-L661 RAID Advanced Software Options License Activation Key for CacheCade 2.0 and FastPath for 1 Controller RAID Advanced Software Options License Activation Key for CacheCade 2.0 and FastPath for 1 Controller H Fujitsu PRIMERGY Server 12 of 18

13 H System configurator and order-information guide PRIMERGY RX900 S2 Status Section VIII Fibre Channel The number of max. I/O PCIe controllers highly depends on the numer of CPUMEMR! The following Table describes the max. number of PCIe controller slots CPUMEMR PCIe slots PCIe slots (PHP) The showm max. numer of each controller is valid,as far as the numer of PCIe slots are available also. S26361-F3961-E1 S26361-F3961-E2 The LPe12* supports Boot from FC 8GBit/s FC Controller 8GBit/s FC Controller Emulex Emulex loose delivery: LPe1250, full height bracket LPe12002, full height bracket Single channel S26361-F3961-L1 8x 1 channel 8GBit/sec FC Controller 2 channel 8GBit/sec FC Controller Dual Channel S26361-F3961-L2 LC Interface for 50µm Fiber LC Interface for 50µm Fiber with mounted LP bracket PCIe x4, 170mm PCIe x4, 170mm FH bracket is not included S26361-F4994-E1 S26361-F4994-E2 The LPe16* supports Boot from FC 16GBit/s FC Controller 16GBit/s FC Controller Emulex Emulex loose delivery: LPe16000, low profile bracket LPe16002, low profile bracket Single channel S26361-F4994-L501 8x 1 channel 16GBit/sec FC Contr. 2 channel 16GBit/sec FC Contr. Dual Channel S26361-F4994-L502 LC Interface for 50µm Fiber LC Interface for 50µm Fiber contains LP and FH brackets. PCIe x8, 170mm PCIe x8, 170mm S26361-F3631-E1 S26361-F3631-E2 The QLE256x do not support Boot via FC 8GBit/s FC Controller 8GBit/s FC Controller Qlogic Qlogic loose delivery: QLE2560, full height bracket QLE2562, full height bracket Single channel S26361-F3631-L1 8x 1 channel 8GBit/sec FC Controller 2 channel 8GBit/sec FC Controller Dual Channel S26361-F3631-L2 LC Interface for 50µm Fiber LC Interface for 50µm Fiber with mounted LP bracket PCIe x4, 170mm PCIe x4, 170mm FH bracket is not included All controllers for the connection of external storage systems are delivered without cables. For the configuration of external cabling see the configurator for external storage systems. For Fibre Channel SAN also other componets like switches, SFPs and optical wires are orderable (for details see price liste) I Fujitsu PRIMERGY Server 13 of 18

14 I PRIMERGY RX900 S2 Status Section IX Communication / Network / CNA / Infiniband The number of max. I/O PCIe controllers highly depends on the numer of CPUMEMR! The following Table describes the max. number of PCIe controller slots CPUMEMR PCIe slots PCIe slots (PHP) The showm max. numer of each controller is valid,as far as the numer of PCIe slots are available also. on-board LAN Controller 3x Dual Gbit Ethernet Contr. on-board Intel NS (Kawela wo/ipsec) ext: 6x RJ45 connector, Cat 5 Teaming: Failover, Load Balancing The Intel LAN Controllers Pro 1000MT, 1000MF, 1000PT, 1000PF can be used with the on-board controller in Teaming Mode Two onboard LAN ports can likewise educate a team. 1x Dual 10Gbit Ethernet Contr. on-board Intel (Niantic wo/ipsec) ext: 2x SFP+ connector Onboard Ethernet Controller The onboard controller are configured in the Basic Unit already. S26361-F3986-E3 SFP+ Module MMF 10GbE LC SFP+ module for 10 Gbit Ethernet FO cabling ext:lc-connector max. 2x per adapter The SFP+ Module is also available as loose delivery S26361-F3986-L3 Instead SFP+ modules, SFP+ twinax cables from switch vendors may be used 2x V:TWX Connector-PY for all Twinax (FJ,BR,CI) max. 2x per controller S26361-F3989-E600 *) S26361-F3873-E500 *) S26361-F4571-E500 *) *) in SA only SFP+ active twinax cable SFP+ active twinax cable SFP+ passive twinax cable shown in customized twinax cable for customized twinax cable for customized twinax cable for cabling view full rack setup ex factory full rack setup ex factory full rack setup ex factory cable length is selected by cable length is selected by cable length is selected by requirement in the factory requirement in the factory requirement in the factory Fujitsu branded cable Brocade branded cable Cisco branded cable max. 2x per controller max. 2x per controller max. 2x per controller separate orderable 10Gb Ethernet cables S26361-F3989-L102 SFP+ aktives Twinax Kabel Fujitsu 2m S26361-F3989-L105 SFP+ aktives Twinax Kabel Fujitsu 5m S26361-F3989-L110 SFP+ aktives Twinax Kabel Fujitsu 10m S26361-F3873-L501 SFP+ aktives Twinax Kabel Brocade 1m S26361-F3873-L503 SFP+ aktives Twinax Kabel Brocade 3m S26361-F3873-L505 SFP+ aktives Twinax Kabel Brocade 5m S26361-F4571-L101 SFP+ passives Twinax Kabel Cisco 1m S26361-F4571-L103 SFP+ passives Twinax Kabel Cisco 3m S26361-F4571-L105 SFP+ passives Twinax Kabel Cisco 5m S26361-F4571-L107 SFP+ aktives Twinax Kabel Cisco 7m S26361-F4571-L110 SFP+ aktives Twinax Kabel Cisco 10m 1Gbit/s Ethernet Adapter S26361-F4610-E2 (I350-T2) Gigabit Ethernet Controller Dual 1000TX PLAN CP 2x1Gbit Cu Intel I350-T2 Intel Powerville based 2 port Server Ad. S26361-F4610-E4 (I350-T4) Gigabit Ethernet Controller Quad 1000TX PLAN CP 4x1Gbit Cu Intel I350-T4 Intel Powerville based 4 port Server Ad. PCIe x4, Low Profile PCIe x4, Low Profile full height (FH) bracket full height (FH) bracket ext: for RJ45-plug, Cat 5 ext: for RJ45-plug, Cat 5 8x while stocks last while stocks last while stocks last S26361-F3740-E1 S26361-F3739-E1 S26361-F3242-E1 (D3035) (D3045) (Sheepshead Bay) Gigabit Ethernet Controller Dual 1000TX Gigabit Ethernet Controller Quad 1000TX Gigabit Ethernet Contr. 1000SX Eth Ctrl 2x1Gbit Cu PCIe x4 D3035 Eth Ctrl 4x1Gbit Cu PCIe x4 D3045 Eth Ctrl 1x1Gbit PCI-e Pro/1000PF LC Intel Powerville based 2 port Server Ad. Intel Powerville based 4 port Server Ad. Intel PRO/1000 PF Server Adapter PCIe x4, Low Profile PCIe x4, Low Profile PCIe x4 full height (FH) bracket full height (FH) bracket ext:lc-connector ext: for RJ45-plug, Cat 5 ext: for RJ45-plug, Cat 5 I1 Loose delivery with FH and LP bracket: I350-T2 S26361-F4610-L502 I350-T4 S26361-F4610-L504 D3035 S26361-F3740-L501 D3045 S26361-F3739-L501 Loose delivery with LP bracket: Sheepshead Bay S26361-F3242-L1 Fujitsu PRIMERGY Server 14 of 18

15 I1 PRIMERGY RX900 S2 Status Gbit/s Ethernet Adapter S26361-F3629-E2 S26361-F3752-E2 (D2755) (Intel X540-T2) 10 Gigabit Ethernet Contr. dual port SFP+ Eth Ctrl 2x10GBase-T Eth Ctrl 2x10Gbit PCIe x8 D2755 SFP+ Intel Twinville based 2 port Server Ad. Intel Niantic based dual port 10Gb NIC PCIe x4, Low Profile PCIe x8, Low Profile, Full Height Bracket FullHeight (FH) bracket ext: 2x SFP+ cage ext: for RJ45-plug, Cat 6 max. 2x per system S26361-F3986-E3 S26361-F3986-E4 V:TWX Connector-PY SFP+ Module MMF 10GbE LC SFP+ Module SMF 10GbE LC for all Twinax (FTS,BR,CI) SFP+ module for 10 Gbit SFP+ module for 10 Gbit max. 2x per controller 8x Ethernet 50µm FO cabling Ethernet 9µm FO cabling ext:lc-sr-connector ext:lc-lr-connector max. 2x per controller max. 2x per controller The SFP+ modules are also available as loose delivery S26361-F3986-L3 S26361-F3986-L4 Instead SFP+ Modules, SFP+ twinax cables from the switch vendors may be used S26361-F3989-E600 *) S26361-F3873-E500 *) S26361-F4571-E500 *) SFP+ active twinax cable SFP+ active twinax cable SFP+ passive twinax cable customized twinax cable for customized twinax cable for customized twinax cable for *) in SA only full rack setup ex factory full rack setup ex factory full rack setup ex factory shown in cable length is selected by cable length is selected by cable length is selected by cabling view requirement in the factory requirement in the factory requirement in the factory Fujitsu branded cable Brocade branded cable Cisco branded cable max. 2x per controller max. 2x per controller max. 2x per controller separate orderable 10Gb Ethernet cables S26361-F3989-L102 SFP+ active Twinax Cable Fujitsu 2m The controller D2755 is delivered without SFP+ modules for optical S26361-F3989-L105 SFP+ active Twinax Cable Fujitsu 5m cables, these must be ordered separately. S26361-F3989-L110 SFP+ active Twinax Cable Fujitsu 10m Loose delivery options (FH and LP bracked included) S26361-F3873-L501 SFP+ active Twinax Cable Brocade 1m D2755 S26361-F3629-L502 S26361-F3873-L503 SFP+ active Twinax Cable Brocade 3m X540-T2 S26361-F3752-L502 S26361-F3873-L505 SFP+ active Twinax Cable Brocade 5m S26361-F4571-L101 SFP+ passive Twinax Cable Cisco 1m S26361-F4571-L103 SFP+ passive Twinax Cable Cisco 3m S26361-F4571-L105 SFP+ passive Twinax Cable Cisco 5m S26361-F4571-L107 SFP+ active Twinax Cable Cisco 7m S26361-F4571-L110 SFP+ active Twinax Cable Cisco 10m F) Fibre Channel over Ethernet S26361-F3592-E2 2 x 10GBit/s CNA Emulex OCe channel 10GBit/sec CNA SFP+ Cage PCIe x8, 170mm max. 8 per system Loose Delivery: S26361-F3592-L2 S26361-F3592-E108 V:TWX Connector-PY The SFP+ Module is also available as loose delivery SFP+ Module MMF 10GbE LC for all Twinax (FTS,BR,CI) S26361-F3591-L108 SFP+ module for 10 Gbit max. 2x per adapter Instead SFP+ Modules, SFP+ twinax cables from 8x Ethernet FO cabling the switch vendors may be used ext:lc-connector max. 2x per adapter 2x S26361-F3989-E600 *) S26361-F3873-E500 *) S26361-F4571-E500 *) SFP+ active twinax cable SFP+ active twinax cable SFP+ passive twinax cable customized twinax cable for customized twinax cable for customized twinax cable for *) in SA only full rack setup ex factory full rack setup ex factory full rack setup ex factory shown in cable length is selected by cable length is selected by cable length is selected by cabling view requirement in the factory requirement in the factory requirement in the factory Fujitsu branded cable Brocade branded cable Cisco branded cable max. 2x per adapter max. 2x per adapter max. 2x per adapter separate orderable 10Gb Ethernet cables S26361-F3989-L102 SFP+ aktives Twinax Kabel Fujitsu 2m S26361-F3989-L105 SFP+ aktives Twinax Kabel Fujitsu 5m S26361-F3989-L110 SFP+ aktives Twinax Kabel Fujitsu 10m S26361-F3873-L501 SFP+ aktives Twinax Kabel Brocade 1m S26361-F3873-L503 SFP+ aktives Twinax Kabel Brocade 3m S26361-F3873-L505 SFP+ aktives Twinax Kabel Brocade 5m S26361-F4571-L101 SFP+ passives Twinax Kabel Cisco 1m S26361-F4571-L103 SFP+ passives Twinax Kabel Cisco 3m S26361-F4571-L105 SFP+ passives Twinax Kabel Cisco 5m S26361-F4571-L107 SFP+ aktives Twinax Kabel Cisco 7m S26361-F4571-L110 SFP+ aktives Twinax Kabel Cisco 10m I2 Fujitsu PRIMERGY Server 15 of 18

16 I2 PRIMERGY RX900 S2 Status G) Infiniband HCA's S26361-F4475-E102 IB HCA 40Gb 1 port QDR IB HCA 1x 40Gb PCIe 2.0 (5,0GT/s) PCIe x8, low profile ext: 1x QSFP-connector max.2x per system Low Profile PCIe form factor with exchangeable Full Height (FH) or Low Profile (LP) bracket max. 2x S26361-F3996-E101 S26361-F3996-E103 If additional length of copper cable or optical cable are needed, InfiniBand Cu Cable 40Gb InfiniBand Cu Cable 40Gb then they must be ordered from the cable vendor directly QSFP, 1m QSFP, 3m max. 1x per adapter max. 1x per adapter S26361-F4475-E202 IB HCA 40Gb 2 port QDR IB HCA 2x 40Gb PCIe 2.0 (5,0GT/s) PCIe x8, low profile ext: 2x QSFP-connector max. 2x per system while stock lasts Low Profile PCIe form factor with exchangeable Full Height (FH) or Low Profile (LP) bracket S26361-F3996-E101 S26361-F3996-E103 If additional length of copper cable or optical cable are needed, InfiniBand Cu Cable 40Gb InfiniBand Cu Cable 40Gb then they must be ordered from the cable vendor directly QSFP, 1m QSFP, 3m max. 2x per adapter max. 2x per adapter J Fujitsu PRIMERGY Server 16 of 18

17 K PRIMERGY RX900 S2 Status Section XI System Management Products (RemoteView) S26361-F1790-E241 irmc S2 advanced pack integrated remote management controller activation key for graphical console redirection and remote media redirection max. 1x per system S26361-F3552-E1 TPM Module Trusted Platform Module on Motherboard Use according to import restrictions max. 1x per system Be aware of import restrictions! Loose delivery for later integration possible for customer. S26361-F3552-L1 TPM Module add-on kit for later integration (loose delivery) Trusted Platform Module on Motherboard Use according to import restrictions max. 1x per system Section XII Optional PSU / power cords / region Kits Base system will be shipped with two PSUs and power cords ICE320 C14->C19 for rack installation. Country specific power cords are not required. In addition to the base configuration with two power supplies units (1+1 redundancy) max. two addition PSU s can be installed. Configurations with more than 4 CPUMEMR require 1 additional PSU for PSU redundancy (2+1 redundancy).or 2 additional PSU for phase redundancy (2+2 redundancy) S26113-F608-E10 For later upgrade the following kit is available: S26113-F608-L10 3./4. power supply module 3./4. power supply module 2000W, hot plug 2000W, hot plug 2x for 2+1 redundancy for 2+1 redundancy for 2+2 redundancy incl. 1x power cord ICE320 C14->C19 (2,5m) max. 4x per system for 2+2 redundancy incl. 1x power cord ICE320 C14->C19 (2,5m) max. 2x per system S26361-F1452-E100 S26361-F1452-E110 S26361-F1452-E130 REGION KIT APAC/EMEA/India REGION KIT JP REGION KIT America For Shipments to Asia pacific, For Shipments to Japan regions For Shipments to America EMEA or India regions 1x per system 1x per system 1x per system End PRIMERGY RX900 S2 Fujitsu PRIMERGY Server 17 of 18

18 PRIMERGY RX900 S2 Status Change Report Date Order number Changes corrected Basic unit order number S26361-F4530-E10 and E S26361-F4610-E4 added Intel I350-T S26361-F4610-E2 added Intel I350-T S26361-F3739-E201 phase out S26361-F3740-E201 phase out S26361-F3610-E202 EOL S26361-F5247-E112 New 1.2TB 2.5" SAS 10K HDD added S26361-F5303-* New SATA SSDs added S26361-F5297-* New SAS SSDs added Optional USB Comps no longer available S26361-F4482-E* HDD Cache updated S26361-F3713-E3 RAID Ctrl SAS 6G 8Port ex 1GB LSI S26361-F3669-E661/L661 RAID advanced SW options added - for RAID Ctrl SAS 6G 8port external S26361-F5228-E*** New 2.5" BC-SAS 7.2K HDD S26361-F3669-E1 removed S26361-F5423-E647 Added 64 GB Memory S26361-F4541-E200 EOL - SSD SAS 200GB, SLC S26361-F4523-E946 Add 128GB / 4x32GB Memory S26361-F4581-Exxx Add SSD SAS MLC S26361-F3669-L100 Loose delivery TFM module added (UJ) S26361-F3669-E1 new int. SAS RAID Controller added S26361-F3257-E270 Change from E170 --> E270 and L110 --> L PCIe-SSD Count changed from 2 > S26361-F3641-E2 new Blue-ray Triple Writer added S26361-F4482-E114 SAS HD 6G 144GB - no longer available S26361-F4541-Ex00 new SAS SSD with 100, 200, 400 GB added - as soon as available S26361-F2201-E20 Cable arm adjusted S26361-F3298-E64 64 GB SSD - no longer available First Release Fujitsu PRIMERGY Server 18 of 18