PowerGlide Multicolour sweeping beam effects

Transcription

1 PowerGlide Multicolour sweeping beam effects M A N U A L V E R S I O N For the latest instruction manual updates and information on the entire Kam range visit: Kam products are manufactured by: Lamba plc, Unit 1, Southfields Road, Dunstable, Bedfordshire, United Kingdom LU6 3EJ Telephone: (+44) (0) Fax: (+44) (0) mail@lambaplc.com Web: If this product is ever no longer functional please take it to a recycling plant for environmentally friendly disposal. Due to continuous product development, specifications and appearance are subject to change. Copyright Lamba plc. E&OE.

2 Thank you for purchasing this Kam product, we are sure that it will serve you for many years to come. To optimise it s performance, please read these instructions carefully to familiarise yourself with the basic operations of the unit. Please retain them for future reference.this unit has been tested at the factory before being shipped to you. To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture. To prevent a fire hazard, do not expose the unit to any naked flame sources. Unplug this apparatus during lightning storms or if it is unlikely to be used for long periods of time. When installing the unit, please ensure you leave enough space around the unit for ventilation. Slots and openings in the unit are provided for ventilation to ensure reliable operation of the product and to protect it from overheating. To prevent fire hazard, the openings should never be blocked or covered. The unit is powered by the mains, always handle the power cable by the plug. Never pull out the plug by pulling on the cable. Never touch the power cable when your hands are wet as this could cause an electric shock. Do not tie a knot in the cable. The power cable should be placed such that it is not likely to be stepped on. A damaged power cable can cause a fire or give you an electrical shock. Check the power cord periodicaly, if you ever find that it is damaged, replace it before using the unit again. Contact your retailer for a replacement. The voltage of the available power supply differs according to country or region. Be sure that the power supply voltage of the area where this unit is to be used meets the requirements of the unit. The lightning flash symbol inside a triangle is to alert the user to the presence high voltage within the unit s enclosure that may be of sufficient power to constitute a risk of electrical shock to persons. Caution: to prevent the risk of electric shock, do not attempt to open the unit. No user-serviceable parts inside. Refer all servicing to qualified service personnel. The exclamation mark inside a triangle is intended to alert the user to the presence of important operating and maintenance instructions in the literature accompanying the appliance. Please read and pay attention to all laser safety warning sticker labels on the unit. Select the installation location of your unit carefully. Avoid placing it in direct sunlight or locations subject to vibration and excessive dust. Do not use the unit where there are extremes in temperature (below 41ºF / 5ºC or exceeding 95ºF / 35ºC). Unpacking and safety Please unpack your new product carefully. Your new product should reach you in perfect condition. Please check that no damage has occurred during transit. If any damage is found, do not operate your unit. Please contact the retailer you purchased it from immediately. If there is any damage to the mains cable do not use the device. Always disconnect the unit from the mains supply when carrying out any cleaning of the unit. Manufacturer declarations In compliance with the following requirements: RoHS Directive (2002/95/EU) and WEEE Directive (2002/96/EU). If this product is ever no longer functional please take it to a recycling plant for environmentally friendly disposal. CE declaration of conformity R&TTE Directive (1999/5/EU), EMC Directive (2004/108/EU), Low Voltage Directive (2006/95/EU). The declarations are available on application from certification@lambaplc.com Before putting the devices into operation, please observe the respective country-specific regulations. AC power The unit is supplied with a power plug appropriate to its voltage. Should any other connections be required they must be carried out with the following configuration: Cable (EU) Cable (US) Pin International Brown Black Live L Light blue White Neutral N Yellow/green Green Earth

3 DMX-512 connection If you are using a standard DMX controller, you can connect the DMX output of the controller directly to the DMX input of the first unit in a DMX chain. If you wish to connect a DMX controller with other XLR outputs you will need to use adapter cables. 1 = ground 2 = minus signal (-) 3 = plus signal (+) Connect the DMX output of the first unit in a DMX chain with the DMX input of the next unit in the chain. Always connect the the output of one unit with the input of the next unit until all units are connected. If you use a controller with 5 pin DMX connection you will need to use a 5 pin to 3 pin adapter. Overhead rigging Important - the installation must be carried out by qualified service personal only. Improper installation can result in serious injuries and /or damage to property. Overhead rigging required extensive experience. Working load limits should be respected, certified installation materials should be used, the installed unit should be inspected regularly for safety. l Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging and servicing. l Locate the unit in a well ventilated spot, far away from any flammable materials and/or liquids. The fixture must be fixed at least 50cm from surrounding walls l The device should be installed out of reach of people and outside of areas where persons may walk by or be seated. l Before rigging make sure that the installation area can hold minimum point load of 10 times the device s weight. l The device should be well fixed; a free swinging mounting is dangerous. l Do not cover any ventilation opening as this may result in overheating Before first time use, the unit should be inspected for safety. Inspection the unit regularly every year. Quick Start Guide After connecting your unit to the mains, use the Control menu on the side panel of the unit to set the operating mode. Use the MENU button to make a function selection, then press ENTER to confirm it. Next use the UP and DOWN arrow buttons to refine your selection, then use the ENTER button to confirm your setting. Running the unit in Auto Show mode Use the side panel Control menu to find and select the Shnd mode and the ENTER button to confirm. Use the UP and DOWN arrow buttons to select your chosen show (Sh0-sh16) and then press ENTER to confirm your choice. You can set the speed of the show using the UP and DOWN arrow buttons (Sp1-sp9). Press the MENU button again to return to the main menu. Running the unit in Sound-to-Light mode Use the side panel Control menu to find and select the SoUd mode then the ENTER button to confirm. Next choose on or off then the ENTER button to confirm. If you have chosen ON, the unit will now respond to music via the built-in microphone. To adjust the sensitivity of the microphone, choose Sens, then the ENTER button to confirm. Use the UP and DOWN arrow buttons to set the sensitivity value from 0 to 100, then press the ENTER button to confirm your choice. Running the unit in DMX mode If you intend to control the unit via DMX, you will need to set the DMX address correctly. Choose Addr then ENTER to confirm. Use the UP and DOWN arrow buttons to set the address number and then press ENTER to confirm your choice. The unit can run in different channel modes. Choose ChNd then ENTER to confirm. Use the UP and DOWN arrow buttons to choose between 1, 6, 8, 12 or 18 channel modes and then press ENTER to confirm your choice. Press the MENU button again to return to the main menu. Running the unit in Master/Slave mode Connect multiple units with DMX cables running from the DMX Output from one unit into the DMX Input of the next unit in the chain. Set the first unit in the chain as the Master unit and set all others to Slave mode. The Slaves will then follow the Master. To set up in Master/Slave mode, use the side panel Control menu to select SLND then NASt on the first (Master) unit. Then select ShNd and choose a Show (Sh 0 to Sh16) then press ENTER to confirm your choice. On all other units, select SLND then choose SL1 or SL2. then press ENTER to confirm your choice. SL1 is normal Slave mode where all units follow the Master unit s operation. Use the SL2 setting if you are only using two units as this mode will make the Slave unit mirror the Master unit and create a better show.

4 Rear panel Control LED display Addr A001 A512 ChNd 1Ch 6Ch 8Ch 12Ch 18Ch SLNd NASt SL 1 SL 2 ShNd sh 0 sh16 sp 1 sp 9 SoUn on off Sens led on off disp dsip tlt1 no Yes tlt2 no Yes test Display Addr ChNd SLNd ShNd Sp1 sp 9 SoUn Sens Led disp tlt1 tlt2 test hour Function Set the DMX address for the unit. Use the Up and Down buttons to set. Set the DMX channel mode. Choose from 1, 6, 8, 12 or 18 channels. Set the unit to Master/Slave mode. Choose Master, Slave 1 or Slave 2. Set the unit to Show mode. Set the pre-programmed show (from 01-16). Sets the speed of the show. Speed setting from 1-9. Set the unit to Sound-to-Light mode. Choose either On or Off. Set the microphone sensitivity. Choose from 0(low) to 100(high) sensitivity. Set the Control LED display to turn off automatically (OFF) or remain on (ON). Rotate the Control LED display 180. Use when unit is mounted upside down. Set the first row Y axis position. Set the first row Y axis reverse position. Set the second row Y axis position. Set the second row Y axis reverse position. Set the unit to run through a series of auto self tests. Unit runtime. hour 0 uer u10 rset 9999 uer rset Software version. Resets the unit.

5 1 channel DMX operation (choose A001 address) Channel Value Function CH1 ( can also be used with Sound-to-Light) No Function Show Show Show Show Show Show Show Show Show Show Show Show Show Show Show Show Sound-to-Light mode 12 channel DMX operation Channel Value Function The first line. Y position The second line. Y position Full dimmer, 0-100% Strobe, slow to fast Colour Colour Colour Colour Colour Colour Colour Colour 8

6 6 / 8 / 18 channel DMX operation 6 channel 8 channel 18 channel Value Function Tilt 1 0 ~ 270 degrees Tilt 1 Driver speed, fast to slow Tilt 2 0 ~ 270 degrees Tilt Driver speed, fast to slow Full dimmer, 0-100% No change Strobe, slow to fast No function R G B W R+G B+W R+G+B R+G+W R+B+W G+B+W R+G+B+W Colour Colour Colour Colour Colour Colour Colour NO change Show 1 16 optional Sound mode Show speed, slow to fast NO change Colour fade Colour fade, slow to fast R+B R+W G+B G+W

7 Technical specifications Kam PowerGlide Mains power AC V 50/60Hz Mains connection IEC mains input and output Fuse F7A L250V Control modes DMX512 / Auto / Sound-to-Light / Master/Slave Light source 8 x 10w CREE 4-in-1 LED Colours Red, green, blue and white Dimming 0 to 100% Red lumi (1m) 7800 x 8 Lux Green lumi (1m) x 8 Lux Blue lumi (1m) x 8 Lux White lumi (1m) x 8 Lux Control setting 4 buttons plus function setting LED display Operating temperature 10~40 DMX512 connections 3 pins XLR input (male) and output (female) DMX512 channels 1 / 6 / 8 / 12 / 18 Dimensions (WxDxH) 400 x 235 x 130mm (not inc brackets) Nett weight 5Kg