Technical manual for two-family Kit Art. KAE5062

Transcription

1 EN TECHNICAL MANUAL Technical manual for two-family Kit Art. KAE506

2 Warning Install the equipment by carefully following the instructions given by the manufacturer and in compliance with the standards in force. Do not tamper with the internal elements offering protection against short circuits and overcurrents. All the equipment must only be used for the purpose it was designed for. Comelit Group S.p.A. declines any responsibility for improper use of the apparatus, for any alterations made by others for any reason or for the use of non-original accessories or materials. All the products comply with the requirements of the 04/0/EU and 04/5/EU directives. This is proved by the CE mark on the products themselves. Do not route the riser wires in proximity to power supply cables (0/400V). Installation, mounting and assistance procedures for electrical devices must only be performed by specialised electricians. Do not press and hold the audio hook while the handset is lifted. Disconnect the power supply before carrying out any maintenance procedures. The electrical system of the building must be fitted with an omnipolar mains switch with a contact opening of at least mm, which is capable of isolating the power supply of the device. Place the protection back over the terminals and close the inspection door after every procedure. Table of contents Warning... Package Contents... Transformer Art Description...4 External unit Art. ET Description...5 Installation...6 Replacing the nameplate holders...6 Internal unit Art. 70W... 7 Description...7 Installation...8 Operating distances and standard diagram... 9 Wiring diagram for standard system and additional door-entry phone connection variant...9 Operating distances...9

3 Package Contents This manual includes information regarding system configuration and customisation which may be perceived as necessary by the installer. KAE506 70W 00 70W ET500 ET500 - External unit 70W - Telephone 00 - Transformer

4 Transformer Art. 00 Description Transformer with 0V primary, V AC / 5 VA secondary winding for continuous use. Dimensions: 5x95x65 mm ( DIN modules) V~. V~.. 0 V digital input.. Secondary V AC output. Disconnect the power supply before carrying out any maintenance procedures. The electrical system of the building must be fitted with an omnipolar mains switch with a contact opening of at least mm, which is capable of isolating the power supply of the device. Place the protection back over the terminals and close the inspection door after every procedure. 4

5 External unit Art. ET500 Description External unit complete with call buttons, wall bracket and flush-mounted box. Dimensions mm (including wall bracket) Surface-mounted wall bracket Art. ET960. A flush-mounted box Art. ET950 is also available.. Stainless steel front faceplate.. Faceplate fixing screw holes. 4. Speaker. 5. Call buttons. 6. Microphone. 7. Speaker. 8. Terminal block for connection: S S Electronic call signal output 4 Negative Loudspeaker input Microphone output ~~* V AC power supply terminals 9. TM Microphone volume adjustment trimmer. 0. TM Loudspeaker volume adjustment trimmer. 5

6 Installation 9,5 cm,5 cm CH ET960 A 4A 5A ET950 CH B 4B 5B Replacing the nameplate holders 6

7 Internal unit Art. 70W Description Audio internal unit complete with key button. Dimensions mm Handset.. Key button.. Speaker. 4. Audio hook. 5. Terminal block: S Electronic call signal input Loudspeaker input Microphone output 4 Negative P Terminal for key button 6. Handset connector. 7

8 Installation mm 05 mm cm 0 cm A B C D max 7cm CLACK! CLACK!

9 Operating distances and standard diagram Wiring diagram for standard system and additional door-entry phone connection variant 70W 70W S 4 P S 4 P 70W S 4 P 70W S 4 P V~ 0V~ ~ 00 ET500 S S 4 ~ ~ * * Local lock release button. EK5/0S Operating distances mm²,5 mm²,5 mm² 00 m 00 m 80 m 0,8 mm² mm² mm² 50 m 50 m 0 m 0,5 mm² 0,8 mm² 0,8 mm² 50 m 50 m 0 m 9

10 ed. Rev. /06 cod. G CERTIFIED MANAGEMENT SYSTEMS Via Don Arrigoni, Rovetta (BG) - Italy