ASI-T-2401DA2RN/D. Item Contents Unit. Size 2.4 inch. Outline Dimension (W x H x D) x x 2.48 mm. Active Area x 48.

Size: px

Start display at page:

Download "ASI-T-2401DA2RN/D. Item Contents Unit. Size 2.4 inch. Outline Dimension (W x H x D) x x 2.48 mm. Active Area x 48."

Branden James
6 years ago
Views:

1 Item Contents Unit Size 24 inch Resolution 240(RGB) x 320 / Interface RGB / CPU / SPI interface / Technology type a-si TFT / Pixel Configuration RGB Vertical Stripe Outline Dimension (W x H x D) 4292 x 6026 x 248 mm Active Area 3672 x 4896 mm Display Mode Transflective, Normally black / Backlight Type LED / Driver IC ILI9325C / Weight 124±5 g

2 Record of Revision Date Revision No Summary Rev 10 was issued Add Reflection parameter Page 2 of 20

3 1 Scope This data sheet is to introduce the specification of ASI-T-2401DA2RN/D active matrix TFT module It is composed of a color TFT-LCD panel, driver ICs, FPC and a backlight unit The 240 display area contains 240(RGB) x 320 pixels 2 Application Digital equipments which need color display, mobile phone, mobile navigator/video systems 3 General Information Item Contents Unit Size 24 inch Resolution 240(RGB) x 320 / Interface RGB / CPU / SPI interface / Technology type a-si TFT / Pixel Configuration RGB Vertical Stripe Outline Dimension (W x H x D) 4292 x 6026 x 248 mm Active Area 3672 x 4896 mm Display Mode Transflective, Normally black / Backlight Type LED / Driver IC ILI9325C / Weight 124±5 g Page 3 of 20

4 ASI-T-2401DA2RN/D 4 Outline Drawing Page 4 of 20

5 5 Interface signals Pin Symbol Function Remark 1 VCI Power Supply for Logic and Booster 2 IOVCC I/O Interface Supply voltage 3 IM0 MCU Interface Select Pin 4 IM1 MCU Interface Select Pin 5 IM2 MCU Interface Select Pin 6 IM3 MCU Interface Select Pin 7 RESET Hardware reset 8 VSYNC 9 HSYNC 10 DOTCLK 11 ENABLE 12 DB17 Date Bit 13 DB16 Date Bit 14 DB15 Date Bit 15 DB14 Date Bit 16 DB13 Date Bit 17 DB12 Date Bit 18 DB11 Date Bit 19 DB10 Date Bit 20 DB9 Date Bit 21 DB8 Date Bit 22 DB7 Date Bit 23 DB6 Date Bit 24 DB5 Date Bit 25 DB4 Date Bit 26 DB3 Date Bit 27 DB2 Date Bit 28 DB1 Date Bit 29 DB0 Date Bit Vertical synchronous signal Fix to the GND level when not in use Horizontal synchronous signal Fix to the GND level when not in use Dot Clock Signal In RGB I/F Fix to the GND level when not in use Data enable single in RGB I/F Low: Select (access enabled) High: Not select (access inhibited) Fix to either IOVcc or GND level when not in use 30 SDO Series data output pin, Let SDO as floating when not used 31 SDI Series data input pin 32 RD Read enable in 80-system interface mode Fix to either IOVCC or GND level when not in use Page 5 of 20

6 33 WR/SCL 34 RS 35 CS 36 GND Ground 37 LEDA Anode for LED 38 LEDK1 Cathode for LED 39 LEDK2 Cathode for LED 40 NC No Connection 41 NC No Connection 42 NC No Connection 43 NC No Connection 44 NC No Connection 45 NC No Connection Write Signal Fix to either IOVCC or GND level when not in use SPI Mode: Synchronizing clock signal in SPI mode Register Index or Register Command Select Fix to either IOVCC or GND level when not in use Chip Select Pin Fix to the GND level when not in use 6 Absolute maximum Ratings 61Electrical Absolute max ratings Parameter Symbol MIN MAX Unit Remark Operating voltage VCI V Power supply for I/O IOVCC V 62Environment Conditions Item Symbol MIN MAX Unit Remark Operating Temperature TOPR Storage Temperature TSTG LED Absolute max atings Item Symbol MIN MAX Unit Remark LED Reverse Voltage Vr - 5 V LED Forward Current IF - 25 V One LED LED Power Dissipation Pd ma Page 6 of 20

7 7 Electrical Specifications 71 Electrical characteristics GND=0V, Ta=25 Parameter Symbol Condition Min Typ Max Unit Note Operating voltage VCI GND= V Operating voltage IOVCC GND= V Input high voltage VIH VCC=28V 08*VDD - VCC V Input low voltage V IL VCC=28V 0-02*V CC V Output high voltage VoH IOH=-01m A 08*VDD - VCC V Output low voltage VoL VCC=28V IOL=01mA 0-02*VCC V Current Consumption ICC-Black VCC=28V ma Power Consumption PLCD mw 72 LED Backlight Ta=25 Item Symbol MIN TYP MAX Unit Remark Forward Current IF ma Forward Voltage VF V LED life time Hr Note Note : The LED life time is defined as the module brightness decrease to 50% original brightness at Ta=25 and IF =40mA The LED lifetime could be decreased if operating IF is larger than 15mA Page 7 of 20

8 73Block Diagram Page 8 of 20

9 8 Command/AC Timing 81 Timing characteristics 811 i80system Interface Timing Characteristics Page 9 of 20

10 812 Serial Data Transfer Interface Timing Characteristics Page 10 of 20

11 813 RGB Interface Timing Characteristics Page 11 of 20

12 814 Reset Timing 82 Initial code 821 Normal operation (16Bit RGB Interface) Page 12 of 20

13 822 Sleep Mode Enter Page 13 of 20

14 823 Sleep Mode Exit Page 14 of 20

15 9 Optical Specification 91 Driving the backlight condition (Transmissive mode) Item Symbol Condition Min Typ Max Unit Remark Contrast Ratio CR θ= Response Time View Angles Chromaticity White Red Green Blue Tr Tf θt θb CR 10 θl θr x y x y Brightness x is on y x y ms ms Note1 Note2 Note1 Note3 Degree Note 4 Note5, Note1 Luminance L cd/m 2 Note1 Note6 Uniformity U % Note1 Note8 92 Not driving the backlight (Reflective mode) Item Symbol Condition Min Typ Max Unit Remark Reflective Contrast Ratio CR θ= Note1 Note2 Reflection Ratio R θ=φ= % Note 7 Reflective View Angles θt θb CR 2 θl θr Degree Note 4 NTSC % Note 5 Page 15 of 20

16 Note 1: Definition of optical measurement system Temperature = 25 (±3 ); LED back-light: ON, Environment brightness < 150 lx Note 2: Contrast ratio is defined as follow: Contrast Ratio = Surface Surface Luminance Luminance with with all white all black pixels pixels Note 3: Response time is defined as follow: Response time is the time required for the display to transition from black to white (Rise Time, Tr) and from white to black(decay Time, Tf) Page 16 of 20

17 Note 4: Viewing angle range is defined as follow: Viewing angle is measured at the center point of the LCD Note 5: Color chromaticity is defined as follow: (CIE1931) Color coordinates measured at center point of LCD area of RGB triangle S 100% area of NTSC triangle Note 6: Luminance is defined as follow: Luminance is defined as the brightness of all pixels White at the center of display area on optimum contrast Page 17 of 20

18 Note 7: Reflectance measurement system is defined as follow: Note 8: Luminance Uniformity is defined as follow: Active area is divided into 9 measuring areas (Refer Fig 2) Every measuring point is placed at the center of each measuring area Uniformity (U) = Minimum Luminance( brightness ) in 9 points Maximum Luminance( brightness ) in 9 points Fig 2 Definition of uniformity Page 18 of 20

19 10 Environmental / Reliability Tests No Test Item Condition Judgment criteria 1 High Temp Operation Ts=+70, 96hrs Per table in below 2 Low Temp Operation Ta=-20, 96hrs Per table in below 3 High Temp Storage Ta=+80, 96hrs Per table in below 4 Low Temp Storage Ta=-30, 96hrs Per table in below 5 6 High Temp & High Ta=+40, 90% RH Humidity Storage 96 hours Thermal Shock (Non-operation) min~ min, Change time:5min, 5 Cycles Per table in below (polarizer discoloration is excluded) Per table in below 7 ESD (Operation) C=150pF, R=330Ω,5points/panel Air:±8KV, 5times; Contact:±4KV, 5 times; Per table in below 8 Vibration (Non-operation) 10Hz~150Hz, 100m/s2, 120min Per table in below Shock 9 (Non-operation) 10 Package Drop Test Half- sine wave,300m/s2,11ms Height:80 cm, 1 corner, 3 edges, 6 surfaces Per table in below Per table in below INSPECTION Appearance Alignment of LCD Panel Electrical current Function / Display CRITERION(after test) No Crack on the FPC, on the LCD Panel No Bubbles in the LCD Panel No other Defects of Alignment in Active area Within device specifications No Broken Circuit, No Short Circuit or No Black line No Other Defects of Display Page 19 of 20

20 11 Precautions for Use of LCD Modules 101 Safety The liquid crystal in the LCD is poisonous Do not put it in your mouth If the liquid crystal touches your skin or clothes, wash it off immediately using soap and water 102 Handling A The LCD and touch panel is made of plate glass Do not subject the panel to mechanical shock or to excessive force on its surface B Do not handle the product by holding the flexible pattern portion in order to assure the reliability C Transparency is an important factor for the touch panel Please wear clear finger sacks, gloves and mask to protect the touch panel from finger print or stain and also hold the portion outside the view area when handling the touch panel D Provide a space so that the panel does not come into contact with other components E To protect the product from external force, put a covering lens (acrylic board or similar board) and keep an appropriate gap between them F Transparent electrodes may be disconnected if the panel is used under environmental conditions where dew condensation occurs G Property of semiconductor devices may be affected when they are exposed to light, possibly resulting in IC malfunctions H To prevent such IC malfunctions, your design and mounting layout shall be done in the way that the IC is not exposed to light in actual use 103 Static Electricity A Ground soldering iron tips, tools and testers when they are in operation B Ground your body when handling the products C Power on the LCD module before applying the voltage to the input terminals D Do not apply voltage which exceeds the absolute maximum rating E Store the products in an anti-electrostatic bag or container 104Storage A Store the products in a dark place at +25 ±10 with low humidity (40% RH to 60% RH) Don't expose to sunlight or fluorescent light B Storage in a clean environment, free from dust, active gas, and solvent 105 Cleaning A Do not wipe the touch panel with dry cloth, as it may cause scratch B Wipe off the stain on the product by using soft cloth moistened with ethanol Do not allow ethanol to get in between the upper film and the bottom glass It may cause peeling issue or defective operation Do not use any organic solvent or detergent other than ethanol 106 Cautions for installing and assembling Bezel edge must be positioned in the area between the Active area and View area The bezel may press the touch screen and cause activation if the edge touches the active area A gap of approximately 05mm is needed between the bezel and the top electrode It may cause unexpected activation if the gap is too narrow There is a tolerance of 02 to 03mm for the outside dimensions of the touch panel and tail A gap must be made to absorb the tolerance in the case and connector Page 20 of 20

ASI-T-430FB2AN/D. Item Contents Unit. Size 4.3 inch. Resolution 480 (RGB) x 272 / Interface RGB / Technology type a-si TFT /

ASI-T-430FB2AN/D. Item Contents Unit. Size 4.3 inch. Resolution 480 (RGB) x 272 / Interface RGB / Technology type a-si TFT / Item Contents Unit Size 4.3 inch Resolution 480 (RGB) x 272 / Interface RGB / Technology type a-si TFT / Pixel pitch 0.198x0.198 mm Pixel Configuration RGB stripes Outline Dimension (W x H x D) 105.50x67.20x3.00