RO 051 S-DIAS Relay Output Module

Transcription

1 RO 051 S-DIAS Relay Output Module Date of creation: Version date: Article number: E

2 Publisher: SIGMATEK GmbH & Co KG A-5112 Lamprechtshausen Tel.: +43/6274/4321 Fax: +43/6274/ Copyright 2015 SIGMATEK GmbH & Co KG Translation from German All rights reserved. No part of this work may be reproduced, edited using an electronic system, duplicated or distributed in any form (print, photocopy, microfilm or in any other process) without the express permission. We reserve the right to make changes in the content without notice. The SIGMATEK GmbH & Co KG is not responsible for technical or printing errors in the handbook and assumes no responsibility for damages that occur through use of this handbook.

3 S-DIAS RELAY OUTPUT MODULE RO 051 S-DIAS Relay Output Module RO 051 with 5 relay outputs The S-DIAS RO 051 relay output module has five relay outputs, each with changeover contacts for 115 V/6 A AC resp. 24 V/6 A DC Page 1

4 RO 051 S-DIAS RELAY OUTPUT MODULE Contents 1 Technical Data Specifications Relay Outputs Relay data V23061-B1007-A Output Circuit Electrical Requirements Miscellaneous Environmental Conditions Mechanical Dimensions Connector Layout Status LEDs Applicable Connectors Label Field Wiring Wiring Example Note Mounting Addressing...17 Page

5 S-DIAS RELAY OUTPUT MODULE RO Technical Data 1.1 Specifications Relay Outputs Number 5 Contact: Relay type changeover contact V23061-B1007-A301 Nominal voltage 24 V DC 115 V AC Switching voltage maximum 30 V maximum 125 V AC Maximum continuous current /channel maximum 6 A DC maximum 6 A AC Concurrence of all outputs 100 % Maximum continuous current allowed per contact of the connector plug Turn-on delay Turn-off delay 6 A DC 6 A AC 10 ms 10 ms Page 3

6 RO 051 S-DIAS RELAY OUTPUT MODULE 1.2 Relay data V23061-B1007-A301 Page

7 S-DIAS RELAY OUTPUT MODULE RO Output Circuit 1.4 Electrical Requirements Voltage supply from S-DIAS bus +5 V Current consumption on the S-DIAS bus (+5 V supply) typically 40 ma maximum 50 ma Voltage supply from S-DIAS bus +24 V Current consumption on the S-DIAS bus (+24 V supply) (all relays active) typically 46 ma at +24 V typically 62 ma at +24 V typically 77 ma at +24 V maximum 54 ma (at +18 V) maximum 72 ma (at +24 V) maximum 91 ma (at +30 V) IMPORTANT: When using the relay output mode, the following minimum supply voltages are required on the supply module depending on the ambient temperature: 18 V: ambient temperature C 18.7 V: ambient temperature V: ambient temperature V: ambient temperature Page 5

8 RO 051 S-DIAS RELAY OUTPUT MODULE If this S-DIAS module is connected to an S-DIAS supply module with several S-DIAS modules, the total current of the modules used must be determined and checked. The total current of the +24 V supply cannot exceed 1.6 A! The total current of the +5 V supply cannot exceed 1.6 A! The specification for the current can be found in the module-specific documentation under "Electrical Requirements". Si ce module S-DIAS est connecté à un module d alimentation S-DIAS suivi de plusieurs modules S-DIAS, le courant total des modules utilisés doit être déterminé et vérifié. Le courant total de l'alimentation +24 V ne peut pas dépasser 1,6 A! Le courant total de l'alimentation +5 V ne peut pas dépasser 1,6 A! Le cahier des charges pour le courant peut être trouvé dans la documentation spécifique au module sous "Spécifications électriques". Page

9 S-DIAS RELAY OUTPUT MODULE RO Page 7

10 RO 051 S-DIAS RELAY OUTPUT MODULE 1.5 Miscellaneous Article number Hardware version 1.x Standard Approbations UL 508 (E247993) UL, cul, CE 1.6 Environmental Conditions Storage temperature C Environmental temperature C Humidity 0-95 %, non-condensing Operating conditions Pollution degree 2 Indoor use altitude up to 2000 m EMC resistance EMC noise generation in accordance with EN (industrial area) in accordance with EN (industrial area) Vibration resistance EN mm from Hz 1g from Hz Shock resistance EN g Protection type EN IP20 Page

11 S-DIAS RELAY OUTPUT MODULE RO Mechanical Dimensions Page 9

12 RO 051 S-DIAS RELAY OUTPUT MODULE 3 Connector Layout 3.1 Status LEDs Module Status green ON module active OFF BLINKING (5 Hz) no supply available no communication User yellow ON can be set from the application OFF BLINKING (2 Hz) (e.g. the module LED can be set to blinking through the visualization so that the module is easily found in the control cabinet) BLINKING (4 Hz) Output status yellow ON Output ON (normally open contact closed) OFF Output OFF (normally open contact open) Page

13 S-DIAS RELAY OUTPUT MODULE RO Applicable Connectors Connectors: X1-X5: Connectors with spring terminals (included in delivery) The spring terminals are suitable connecting ultrasonically compacted (ultrasonically welded) strands. Connections: Stripping length/sleeve length: Mating direction: 10 mm Conductor cross section rigid: mm 2 Conductor cross section flexible: mm 2 Conductor cross section ultrasonically compacted: mm 2 Conductor cross section AWG/kcmil: Conductor cross section flexible with ferrule without with plastic sleeve: Conductor cross section flexible with ferrule with plastic sleeve: parallel to the connector axis resp. to the connector board mm mm 2 (reason for reduction d2 of the ferrule) Page 11

14 RO 051 S-DIAS RELAY OUTPUT MODULE 3.3 Label Field Manufacturer Type Weidmüller MF 10/5 CABUR MC NE WS Weidmüller article number Compatible printer Type Weidmüller Printjet Advanced 230V Weidmüller article number Page

15 S-DIAS RELAY OUTPUT MODULE RO Wiring 4.1 Wiring Example Page 13

16 RO 051 S-DIAS RELAY OUTPUT MODULE 4.2 Note The input filters, which suppress noise signals, allow operation in harsh environmental conditions. A careful wiring method is also recommended to ensure error-free function. The following guidelines should be observed: Avoid parallel connections between input lines and load-bearing circuits. Protective circuits for all relays (RC networks or free-wheeling diodes) Correct wiring to ground The ground bus should be connected to the control cabinet when possible! Si possible la terre doit être connectée à l'armoire de commande! IMPORTANT: The S-DIAS module cannot be connected/disconnected while voltage is applied! IMPORTANT: Le module S-Dias NE PEUT PAS être inséré ou retiré sous tension. Page

17 S-DIAS RELAY OUTPUT MODULE RO Mounting The S-DIAS modules are designed for installation into the control cabinet. To mount the modules a DIN-rail is required. The DIN rail must establish a conductive connection with the back wall of the control cabinet. The individual S-DIAS modules are mounted on the DIN rail as a block and secured with latches. The modules must be mounted horizontally (module label up) with sufficient clearance between the ventilation slots of the S-DIAS module blocks and nearby components and/or the control cabinet wall. This is necessary for optimal cooling and air circulation, so that proper function up to the maximum operating temperature is ensured Page 15

18 RO 051 S-DIAS RELAY OUTPUT MODULE Recommended minimum distances of the S-DIAS modules to the surrounding components or control cabinet wall: a, b, c distances in mm (inches) Page

19 S-DIAS RELAY OUTPUT MODULE RO Addressing Address (hex) Memory Size (bytes) Access Type Description Reset Value Output register w r Bit 0 Output 1-Relay 1 Bit 1 Output 2-Relay 2 Bit 2 Output 3-Relay 3 Bit 3 Output 4-Relay 4 Bit 4 Output 5-Relay 5 Bit 5-7 Reserved 24 V status Bit 0 Bit 1-7 DC 24 V OK Reserved Page 17

20 RO 051 S-DIAS RELAY OUTPUT MODULE Documentation Changes Change date Affected page(s) Chapter Note normally open to changeover mechanical dimensions corrected Specifications relay outputs 1.2 Relay data Relay type added in the table Title changed to Relay data V23061-A1007-A Miscellaneous Standard changed Electrical Requirements Graphic added Mounting Graphics distances Environmental Conditions 3.2 Applicable Connectors 3.3 Label Field 5 Mounting Added operating conditions Added sleeve length Added info regarding ultrasonically welded strands Added chapter Graphic replaced Page