Relays for Various Protection Applications / 7SV600

Size: px
Start display at page:

Download "Relays for Various Protection Applications / 7SV600"

Transcription

1 Relays for Various Protection Applications / SV00 SIPROTEC SV00 numerical circuit-breaker failure protection relay Fig. 0/ Description SIPROTEC SV00 numerical circuit-breaker failure protection relay The SIPROTEC SV00 is a numerical relay used for circuitbreaker failure protection. A failure occurs when the circuitbreaker fails to correctly open and clear the fault after single or three-pole trip commands have been issued by the protection unit. It is then necessary to trip the relevant busbar zone (section) to ensure fault clearance. Generally, the monitoring of the current is sufficient as the criterion for the indication that the circuit-breaker has successfully cleared the fault ( current condition ). However, under certain fault conditions (e.g. overvoltage), little or no current may flow, making the measurement of current unreliable for indication of the circuit- breaker status ( no current condition ). The SV00 operates correctly for both these conditions. The relay is suitable for use at all voltage levels and in all applications. The current transformers can either be of the closed iron core or linear type. The relay can be incorporated in conventional switchgear systems and modem substation control systems e.g. SICAM. LSP00-afpen.tif Function overview Protection functions Circuit-breaker failure protection (single or three-pole with/ without current) Independently settable delay times for operation with and without current Single or two-stage time delay of the busbar trip command Re-trip (cross trip) stage ( st stage of the -stage operation) Intertrip facility (via teleprotection interface) End-fault protection with intertrip No current control using the circuit-breaker auxiliary contacts Features Highly sensitive current detection -out-of- check of the current detectors Short reset time, negligible overshoot time Can be initiated by phase-segregated or common-phase trip commands End-fault protection Assignable output relays, LEDs and binary inputs Monitoring functions Monitoring of circuit-breaker auxiliary contacts Operational current measured values Self-supervision of the relay Event buffer Fault protocols Oscillographic fault recording Communication interfaces x RS interface IEC protocol DIGSI Hardware Digital inputs: binary inputs Digital outputs: output relays Front design Display for operation and measured values LEDs for local alarm 0 Siemens SIP Edition No. 0/

2 Relays for Various Protection Applications / SV00 Application Application The numerical circuit-breaker failure protection relay SV00 provides rapid backup fault clearance instruction to the associated circuit-breakers in case the circuit-breaker nearest to the fault fails to respond. It is suitable for power systems of all voltage levels. The initiation signal can be derived from any protection or supervision equipment or, in case of manual opening, from the control discrepancy switch of the breaker. Information from the circuit-breaker auxiliary contact is required for the breaker failure protection to function during faults which produce little or no current flow (possible only with common-phase initiation). Simplified application diagram of circuit-breaker failure protection. Fig. 0/ Typical applications Simplified application diagram of circuit-breaker failure protection by means of a circuit-breaker auxiliary contact. 0 0/ Siemens SIP Edition No.

3 Relays for Various Protection Applications / SV00 Construction, protection functions Construction The relay contains all the components needed for Acquisition and evaluation of measured values Operation and display Output of signals and trip commands Input and evaluation of binary signals SCADA interface (RS) Power supply The rated CT currents applied to the SIPROTEC SV00 can be or A. This is selectable via a jumper inside the relay. Three different housings are available. The flush-mounting versions have terminals accessible from the rear. The surfacemounting version has terminals accessible from the front. LSP00-afpen.tif Protection functions Fig. 0/ Rear view of surface-mounting housing The breaker failure protection can operate single-stage or twostage. When used as single-stage protection, the bus trip command is given to the adjacent circuit-breakers if the protected feeder breaker fails. When used as two-stage protection, the first stage can be used to repeat the trip command to the relevant feeder breaker, normally on a different trip coil, if the initial trip command from the feeder protection is not successful. The second stage will result in a bus trip to the adjacent breakers, if the command of the first stage is not successful. The bus trip command from the breaker failure protection can be routed to all circuit-breakers linked to the same busbar (section) as the breaker that failed. It can also be transmitted to the remote end by means of a suitable communication link (e.g. PLC, radio wave, or optical fiber). The isolator replica which is necessary in case of multiple busbar sections is not part of the SV00 relay. The current level is monitored in each of the three phases against a set threshold. In addition, the zero-sequence component or the negative-sequence component of the phase currents derived by symmetrical component analysis is monitored. This ensures high security against malfunction by use of a -out-of- check of the current detectors. The version with phase-segregated initiation enables reliable breaker failure detection even during single-pole auto-reclose cycles, provided the phase-segregated trip signals of the feeder protection are connected to the SV00. If the protected circuit-breaker is not operational (e.g. air pressure failure or spring not charged), instantaneous bus trip of the adjacent circuit-breakers can be achieved following a feeder protection trip, provided the relay is informed via binary input of the breaker status (possible only for common-phase initiation). An end-fault protection function is integrated in the SV00 relay. An end fault is a short-circuit located between the circuitbreaker and the current transformer set of the feeder. For this fault, current flow is detected, although the auxiliary contacts of the breaker indicate open breaker poles. A command signal is generated which can be transmitted to the remote-end breaker (possible only for common-phase initiation). Special measures are taken to prevent malfunction of the relay. Besides the mentioned -out-of- check of the current detection elements, the trip signals of the feeder protection can be connected in a redundant manner, so that they can be checked for plausibility (possible only for common-phase initiation). Continuous monitoring of the measured values permits rapid annunciation of any fault in the instrument transformer circuits. Continuous plausibility monitoring of the internal measured value processing circuits and monitoring of the auxiliary voltages to ensure that they remain within tolerance are obviously inherent features. 0 Siemens SIP Edition No. 0/

4 Relays for Various Protection Applications / SV00 Serial data transmission, connection diagrams Serial data transmission A PC can be connected to ease setup of the relay using the Windows-based program DIGSI which runs under MS-Windows. It can also be used to evaluate up to oscillographic fault records, fault logs and the operational event buffer. As an option, a system interface is available. The SIPROTEC SV00 transmits a subset of data via IEC protocol: General fault detection of the device General trip of the device Current in phase L [%] = Breaker failure trip T (local trip) Breaker failure trip T (busbar trip) Circuit-breaker defective: Trip Trip by end-fault protection Trip by monitoring current symmetry Breaker failure protection is active Fig. 0/ Wiring communication RS For convenient wiring of the RS bus, use bus cable system XV0 (see part of this catalog) Connection diagrams 0 Fig. 0/0 Connection example for single-stage breaker failure protection with phase-segregated initiation 0/ Siemens SIP Edition No.

5 Relays for Various Protection Applications / SV00 Connection diagrams Fig. 0/ Connection example for -stage breaker failure protection, common-phase initiation, CB interrogation 0 Fig. 0/ Connection example for single-stage breaker failure protection with common-phase initation and Buchholz protection, CB interrogation is imperative; additional intertrip signal to the opposite line end in case of breaker failure or end fault Siemens SIP Edition No. 0/

6 Relays for Various Protection Applications / SV00 Technical data General unit data Measuring circuits Rated current I N Rated frequency f N can be parameterized Power consumption of current inputs At I N = A At I N = A Overload capability current path, Thermal (r.m.s.) to A 0 or 0 Hz (selectable) < 0. VA < 0. VA 00 x I N for s 0 x I N for 0 s x I N continuous Dynamic (pulse current) 0 x I N one half cycle Auxiliary voltage Power supply via integrated DC/DC converter Rated auxiliary voltage V Aux DC DC / V DC 0 / 0 / V DC 0 / 0 V Permissible variations DC to V DC to 0 V DC to 00 V Binary inputs Number Rated operating voltage Current consumption Pick-up threshold Rated aux. voltage DC //0 V Rated aux. voltage DC 0//0/0 V Unit design Housing Dimensions Weight In housing for surface mounting In housing for flush mounting Degree of protection acc. to EN 0 Housing Terminals Serial interface (can be marshalled) DC to 0 V Approx.. ma, independent of operating voltage selectable by plug-in jumpers V pickup DC V V drop-off < DC V V pickup DC V V drop-off < DC V XP0 Refer to part for dimension drawings Approx.. kg Approx..0 kg IP IP 0 Superimposed AC voltage Peak-to-peak Power consumption Quiescent Energized Bridging time during failure/shortcircuit of auxiliary voltage Rated auxiliary voltage V Aux Permissible variations Heavy duty (command) contacts Command (trip) relays, number Contacts per relays Switching capacity Make Break Switching voltage Permissible current Signal contacts Signal / alarm relays Contact per relays Switching capacity Make Break Switching voltage Permissible current % at rated voltage % at limits of admissible voltage Approx. W Approx. W 0 ms at V rated DC 0 V 0 ms at V rated DC V AC V, 0/0 Hz AC 0 V, 0/0 Hz AC to V AC to V (can be marshalled) NO 000 W / VA 0 W / VA 0 V A continuous 0 A for 0. s (can be marshalled) CO 000 W / VA 0 W / VA 0 V A Isolated Standard Test voltage Connection Baud rate Electrical tests Specifications Standards Insulation tests High voltage test (routine test) except DC voltage supply input and RS High voltage test (routine test) only DC voltage supply input and RS High voltage test (type test) Between open contacts of trip relays Between open contacts of alarm relays Impulse voltage test (type test) all circuits, class III RS DC. kv Data cable on terminals, two data wires, one frame reference, for connection of a personal computer or similar; core pairs with shield, shield must be grounded; communication possible via modem As delivered 00 baud min. 00 baud; max. 00 baud IEC 0-; ANSI/IEEE C.0.0 kv (r.m.s.); 0 Hz DC. kv. kv (r.m.s.), 0 Hz kv (r.m.s.), 0 Hz kv (peak);./0 µs; 0. J; positive and negative impulses at intervals of s 0/ Siemens SIP Edition No.

7 Relays for Various Protection Applications / SV00 Technical data EMC tests for noise immunity; type tests Standards: IEC 0-, IEC 0- (product standards); EN 00- (generic standard) VDE 0, part 0 High frequency IEC 0--, class III Electrostatic discharge IEC 0--, class III and IEC 000--, class III Irradiation with radio-frequency field, non-modulated; IEC 0-- (report), class III Irradiation with radio-frequency field, amplitude-modulated; IEC 000--, class III Irradiation with radio-frequency field, pulse-modulated; IEC 000--/ENV 00, class III Fast transients/bursts IEC 0-- and IEC 000--, class III Line-conducted HF, amplitudemodulated IEC 000--, class III Magnetic field with power frequency IEC 000--, class IV IEC 0- Oscillatory surge withstand capability ANSI/IEEE C.0. (common mode) Fast transient surge withstand capability ANSI/IEEE C.0. (common mode) Radiated electromagnetic interference ANSI/IEEE C.0. High frequency test document C (SEC) 0. kv (peak); MHz; τ = µs; 00 shots/s; duration s kv/ kv contact discharge; kv air discharge; both polarities; 0 pf; R i = 0 Ω 0 V/m; to 00 MHz 0 V/m; 0 to 000 MHz; 0 % AM; khz 0 V/m; 00 MHz; repetition frequency 00 Hz; duty cycle 0 % kv; /0 ns; khz; burst length ms; repetition rate 00 ms; both polarities; R i = 0 Ω; duration min 0 V; 0 khz to 0 MHz; 0 % AM; khz 0 A/m continuous; 00 A/m for s; 0 Hz 0. mt; 0 Hz. to kv (peak); to. MHz, decaying oscillation; 0 surges per s; duration s; R i = 0 Ω to 00 Ω to kv; 0/0 ns; 0 surges per s; both polarities; duration s; R i = 0 Ω 0 to 0 V/m; to 000 MHz; amplitude and pulse modulated. kv (peak, alternating polarity); 00 khz, MHz, 0 and 0 MHz, decaying oscillation; R i = 0 Ω EMC tests for interference emission; type tests Standard EN 00-* (generic standard) Conducted interference voltage, 0 to 0 MHz aux. voltage CISPR, EN 0 Limit class B Radio interference field strength CISPR, EN 0 0 to 000 MHz Limit class A Mechanical stress tests Vibration, shock stress and seismic vibration During operation Standards IEC 0- and IEC 00- Vibration IEC 0--, class I IEC 00-- Shock IEC 0--, class I Seismic vibration IEC 0--, class I IEC 00-- During transportation Standard Vibration IEC 0--, class II IEC 00-- Shock IEC 0--, class I IEC 00-- Continuous shock IEC 0--, class I IEC 00-- Sinusoidal 0 to 0 Hz: ± 0.0 mm amplitude; 0 to 0 Hz: 0. g acceleration Sweep rate octave/min 0 cycles in orthogonal axes Half-sine Acceleration g, duration ms, shocks in each direction of orthogonal axes Sinusoidal to Hz: ±. mm amplitude (horizontal axis) to Hz: ±. mm amplitude (vertical axis) to Hz: g acceleration (horizontal axis) to Hz: 0. g acceleration (vertical axis) Sweep rate octave/min cycle in orthogonal axes IEC 0- and IEC 00- Sinusoidal to Hz: ±. mm amplitude; to 0 Hz: g acceleration Sweep rate octave/min 0 cycles in orthogonal axes Half-sine Acceleration g, duration ms, shocks in each direction of orthogonal axes Half-sine Acceleration 0 g, duration ms, 000 shocks in each direction of orthogonal axes 0 Siemens SIP Edition No. 0/

8 Relays for Various Protection Applications / SV00 Technical data 0 Climatic stress tests Temperatures Permissible temperature during service Recommended temperature during service Permissible temperature during storage Permissible temperature during transport Storage and transport with standard works packaging! Humidity Permissible humidity We recommend that all units are installed such that they are not subjected to direct sunlight, nor to large temperature fluctuations which may give rise to condensation. Service conditions The relay is designed for use in industrial environment, for installation in standard relay rooms and compartments so that with proper installation electromagnetic compatibility (EMC) is ensured. The following should also be heeded: All contactors and relays which operate in the same cubicle or on the same relay panel as the digital protection equipment should, as a rule, be fitted with suitable spike quenching elements. All external connection leads in substations from 00 kv upwards should be shielded with a shield capable of carrying power currents and grounded at both sides. No special measures are normally necessary for substations of lower voltages. 0 C to +0 C (> C decreased display contrast) C to + C C to + C C to +0 C Mean value per year % relative humidity; on 0 days per year % relative humidity; condensation not permissible! The shield of the RS cable must be grounded. It is not permissible to withdraw or insert individual modules under voltage. In the withdrawn condition, some components are electrostatically endangered; during handling the standards for electrostatically endangered components must be observed. The modules are not endangered when plugged in. WARNING! The relay is not designed for use in residential, commercial or light-industrial environment as defined in EN 00. Functions Breaker supervision Current detection Setting range Drop-off ratio Tolerance Initiation conditions Depending on ordered version Times Pickup time Drop-off time with sinusoidal measured quantities Drop-off time maximum Delay times for all time stages 0.0 x I N to.00 x I N (steps 0.0 x I N ) Approx x I N or % of set value Phase-segregated initiation (singlepole trip from feeder protection) or common-phase initiation (threepole trip from feeder protection) and common-phase initiation (three-pole trip from non-shortcircuit protection) Approx. ms with measured quantities present Approx. ms after switch-on of measured quantities 0 ms ms 0.00 s to.00 s (steps 0.0 ms) or deactivated Delay time tolerance % of set value or 0 ms The set times are pure delay times. Additional functions Operational value measurements Operational current values Measurement range Tolerance I L ; I L ; I L 0 % to 0 % I N % of rated value or of measured value Steady-state measured value supervision Current unbalance I max / I min > symmetry factor as long as I > I limit Fault event data storage Storage of annunciations of the last eight faults with max. 0 messages each Time assignment Resolution for operational annunciations Resolution for fault event annunciations s ms Max. time deviation 0.0 % Data storage for fault recording (max. fault events) Total storage time (fault detection or trip command = 0 ms) Max. s, selectable pre-trigger and post-fault time Max. storage period per fault event T max Pre-trigger time T pre Post-fault time T post 0.0 to.00 s (steps 0.0 s) 0.0 to 0.0 s (steps 0.0 s) 0.0 to 0.0 s (steps 0.0 s) Sampling rate instantaneous value per ms at 0 Hz instantaneous value per 0. ms at 0 Hz 0/ Siemens SIP Edition No.

9 Relays for Various Protection Applications / SV00 Selection and ordering data Description Order No. SV00 numerical circuit-breaker failure protection relay SV00 - A A 0 - D A 0 Rated current; rated frequency A; 0/0 Hz A; 0/0 Hz Rated auxiliary voltage DC, V DC 0, 0, V DC 0, 0 V / AC V, 0/0 Hz AC 0 V, 0/0 Hz Unit design For panel surface mounting with terminals on both sides For panel surface mounting with terminals at top and bottom For panel flush mounting / cubicle mounting B D E Options For common-phase initiation For common-phase initiation or phase-segregated initiation 0 Accessories Description Order No. DIGSI Software for configuration and operation of Siemens protection units running under MS Windows (version Windows 000/ XP Professional Edition) device templates, Comtrade Viewer, electronic manual included as well as Getting started manual on paper, connecting cables (copper) Basis Full version with license for 0 computers, on CD-ROM (authorization by serial number) Professional DIGSI Basis and additionally SIGRA (fault record analysis), CFC Editor (logic editor), Display Editor (editor for default and control displays) and DIGSI Remote (remote operation) XS00-0AA00 XS0-0AA00 RS (V.) RS converter * XV00-00 Plug-in auxiliary power supply unit AC 0 V / 0 Hz 0 Plug-in auxiliary power supply unit AC 0 V / 0 Hz 0 With RS connecting cable for SJ, RW, SD, SV A With RS connecting cable with -pin connector for SIMEAS Q With RS connecting cable with plug connector for SIMEAS T Without RS connecting cable With RS connecting cable XV00- for PC/notebook, -pin connector (female) With RS adapter, -pin connector (male) to -pin connector (female) for connection to notebook/pc Converter full-duplex fiber-optic cable RS With power supply DC 0 V and AC 0 /0 V Manual for SV00 For the latest version please visit *) RS bus system up to kbaud RS bus cable and adaptor XV0- AA ; see part. A B C A B C XV0-0BA00 Siemens SIP Edition No. 0/

10 Relays for Various Protection Applications / SV00 Connection diagram Fig. 0/ General connection diagram of SV00 with presettings for common-phase initiation 0 Fig. 0/ General connection diagram of SV00 with presettings for phase-segregated initiation 0/0 Siemens SIP Edition No.

SIPROTEC 7SV600 Numerical Circuit-Breaker Failure Protection Relay

SIPROTEC 7SV600 Numerical Circuit-Breaker Failure Protection Relay SIPROTEC 7SV600 Numerical Circuit-Breaker Failure Protection Relay Function overview Description The SIPROTEC 7SV600 is a numerical relay used for circuit-breaker failure protection. A failure occurs when

More information

SIPROTEC easy 7SJ45 Numerical Overcurrent Protection Relay Powered by CTs

SIPROTEC easy 7SJ45 Numerical Overcurrent Protection Relay Powered by CTs SIPROTEC easy 7SJ4 Numerical Overcurrent Protection Relay Powered by CTs Function overview Fig. /1 Description The SIPROTEC easy 7SJ4 is a numerical overcurrent protection relay which is primarily intended

More information

Tripping Matrix Device 7UW5010. As of Tripping Circuit Management Unit or Non-electric Protection Device. Catalog 1.0. Answers for energy.

Tripping Matrix Device 7UW5010. As of Tripping Circuit Management Unit or Non-electric Protection Device. Catalog 1.0. Answers for energy. Tripping Matrix Device 7UW50 As of Tripping Circuit Management Unit or Non-electric Protection Device Catalog.0 Answers for energy. TRIPPING MATRIX DEVICE 7UW50 As of Tripping Circuit Management Unit or

More information

SIPROTEC 4 7SS52 Distributed Numerical Busbar and Breaker Failure Protection

SIPROTEC 4 7SS52 Distributed Numerical Busbar and Breaker Failure Protection Busbar Differential Protection / 7SS52 SIPROTEC 4 7SS52 Distributed Numerical Busbar and Breaker Failure Protection Fig. /18 SIPROTEC 4 7SS52 busbar protection system Description The SIPROTEC 7SS52 numerical

More information

SIPROTEC 4 6MD66 High-Voltage Bay Control Unit

SIPROTEC 4 6MD66 High-Voltage Bay Control Unit Substation Automation / 6MD66 SIPROTEC 4 6MD66 High-Voltage Bay Control Unit Fig. /10 SIPROTEC 4 6MD66 high-voltage bay control unit Description The 6MD66 high-voltage bay control unit is the control unit

More information

Busbar Differential Protection

Busbar Differential Protection Busbar Differential Protection Page SIPROTEC 7SS60 Centralized Numerical Busbar Protection /3 SIPROTEC 4 7SS52 Distributed Numerical Busbar and Breaker Failure Protection /1 /2 Busbar Differential Protection

More information

Combined Overcurrent and Earth-fault Relay SPAJ 140 C. Product Guide

Combined Overcurrent and Earth-fault Relay SPAJ 140 C. Product Guide Combined Overcurrent and Earth-fault Product Guide Issued: April 1999 Status: Updated Version: C/18.04.2006 Data subject to change without notice Features Three-phase, low-set phase overcurrent unit with

More information

Arc protection relay. Features Three-phase overcurrent function. Application

Arc protection relay. Features Three-phase overcurrent function. Application Arc protection relay REA 10_ Page 1 Issued: May 1999 Status: New Data subject to change without notice Features Three-phase overcurrent function Loop-type or radial sensor fibre for arc detection Two high-speed

More information

Sensitive Earth-fault Relay SPAJ 111 C. Product Guide

Sensitive Earth-fault Relay SPAJ 111 C. Product Guide Issued: April 1999 Status: Update Version: C/12.04.2006 Data subject to change without notice Features Sensitive low-set neutral overcurrent stage with definite time characteristic High-set neutral overcurrent

More information

IRI1-ES Sensitive Earth Fault Current Relay. Manual IRI1-ES (Revision A)

IRI1-ES Sensitive Earth Fault Current Relay. Manual IRI1-ES (Revision A) IRI1-ES Sensitive Earth Fault Current Relay Manual IRI1-ES (Revision A) Woodward Manual IRI1-ES GB Woodward Governor Company reserves the right to update any portion of this publication at any time. Information

More information

Earth-fault Relay SPAJ 110 C. Product Guide

Earth-fault Relay SPAJ 110 C. Product Guide Issued: April 1999 Status: Updated Version: C/12.04.2006 Data subject to change without notice Features Low-set neutral overcurrent stage with definite time or inverse time characteristic High-set neutral

More information

Feeder protection relay SPAA 121 C. Product Guide

Feeder protection relay SPAA 121 C. Product Guide Issued: April 1999 Status: Updated Version: C/06.03.2006 Data subject to change without notice Features Two-phase low-set phase overcurrent unit with definite time or inverse time characteristic Two-phase

More information

Synchro-check relay. Application

Synchro-check relay. Application Issued: April 1999 Status: Updated Version: B/08.11.2001 Data subject to change without notice Features Two identical operation stages allowing the closing conditions of two separate circuit breakers to

More information

TF501, TF521 Terminal Bases

TF501, TF521 Terminal Bases Ordering Data DATA SHEET TF501, TF521 Terminal Bases 1 Ordering Data Part No. Scope of delivery Product life cycle status 1SAP 117 000 R0271 1SAP 317 000 R0271 1SAP 117 200 R0271 1SAP 317 200 R0271 TF501-CMS,

More information

Arc protection relay. Features Three-phase overcurrent function. Application

Arc protection relay. Features Three-phase overcurrent function. Application Arc protection relay REA 10_ Issued: May 1999 Status: Updated Version: B/12.11.2001 Data subject to change without notice Features Three-phase overcurrent function Loop-type or radial sensor fibre for

More information

TU531, TU532 Terminal Unit

TU531, TU532 Terminal Unit Ordering Data DATA SHEET TU531, TU532 Terminal Unit 1 Ordering Data Part No. Description Product Life Cycle Phase *) 1SAP 217 200 R0001 1SAP 217 000 R0001 1SAP 417 000 R0001 TU531, terminal unit, 230 VAC,

More information

Part No. Description Product Life Cycle Phase *) unit, 24 VDC, spring terminals. unit, 24 VDC, spring terminals, XC version

Part No. Description Product Life Cycle Phase *) unit, 24 VDC, spring terminals. unit, 24 VDC, spring terminals, XC version Ordering Data DATA SHEET TU520 Terminal Unit 1 Ordering Data Part No. Description Product Life Cycle Phase *) 1SAP 214 400 R0001 1SAP 414 400 R0001 TU520-ETH, PROFINET I/O terminal unit, 24 VDC, spring

More information

DRS-LA413. Circuit Breaker Failure Relay. Operating Principle DRS-LA413. Operating Principle. Revision: 2 from Dwg.No.: DIL

DRS-LA413. Circuit Breaker Failure Relay. Operating Principle DRS-LA413. Operating Principle. Revision: 2 from Dwg.No.: DIL Circuit Breaker Failure Relay Operating Principle Revision: 2 from 2005-02-25 Edition: 2005-02-25 _CBF-description_eng.doc Page 1 /14 Table of Contents: 1 GENERAL DESCRIPTION 4 2 FUNCTIONAL DESCRIPTION

More information

Accessories / 7XV5662

Accessories / 7XV5662 Accessories / XV Communication Converter XV-0AA00/GG for X. / RS / G.0. *) Fig. / Communication converter for X./ RS and G.0. The communication converter CC-XG for coupling to a communication network is

More information

02/11/2015

02/11/2015 35 mm - 1 Relay 8A OUR1 Part number 88867105 Multi-function or mono-function Multi-range Multi-voltage Relay output 1 or 2 : 8 A - 250 V (10 A UL) LED status indicator Option of connecting an external

More information

Residual overvoltage relay

Residual overvoltage relay Page 1 Issued: April 1999 Status: New Data subject to change without notice Features Definite-time residual overvoltage earthfault protection and supervision Two independent operation stages, e.g. one

More information

DI561 Digital Input Module

DI561 Digital Input Module Ordering Data DATA SHEET DI561 Digital Input Module 1 Ordering Data Part No. Description Product Life Cycle Phase *) 1TNE 968 902 R2101 1TNE 968 901 R3101 1TNE 968 901 R3103 1TNE 968 901 R3105 DI561, digital

More information

Electronic timer CT-AHD.22

Electronic timer CT-AHD.22 2CDC 251 093 F0t06 a Rotary switch for the preselection of the time range b Potentiometer with direct reading scale for the fine adjustment of the time delay c U: green LED V control supply voltage applied

More information

High-Tech Range IRI1-ES- Sensitive Earth Fault Current Relay

High-Tech Range IRI1-ES- Sensitive Earth Fault Current Relay High-Tech Range IRI1-ES- Sensitive Earth Fault Current Relay IE ON RESET.5 X1 t IE X1.6%.2.4.8 1.6 X1.1s.2.4.8 1.6 X2 OFF ON S1 S2 IRI1-ES IRI1-ES C&S Electric Limited (Protection & Control Division) Contents

More information

Protection Relays PHASE & RESIDUAL OVERCURRENT

Protection Relays PHASE & RESIDUAL OVERCURRENT Protection Relays PHASE & RESIDUAL OVERCURRENT Application The relay type NA016 can be used in radial networks as feeder or power transformer protection. In solidly grounded systems the residual overcurrent

More information

DI572 Digital Input Module

DI572 Digital Input Module Ordering Data DATA SHEET DI572 Digital Input Module 1 Ordering Data Part No. Description Product Life Cycle Phase *) 1SAP 230 500 R0000 1TNE 968 901 R3101 1TNE 968 901 R3102 1TNE 968 901 R3103 1TNE 968

More information

Feeder protection relay

Feeder protection relay Page 1 Issued: April 1999 Status: New Data subject to change without notice Features Comprehensive numerical feeder protection relay consisting of two multi-function protection relay modules and a flexible

More information

Feeder protection relay SPAA 341 C. Product Guide

Feeder protection relay SPAA 341 C. Product Guide Issued: April 1999 Status: Updated Version: D/07.03.2006 Data subject to change without notice Features Comprehensive numerical feeder protection relay consisting of two multi-function protection relay

More information

DC522 Digital Input/Output Module

DC522 Digital Input/Output Module Ordering Data DATA SHEET DC522 Digital Input/Output Module 1 Ordering Data Part No. Description Product Life Cycle Phase *) 1SAP 240 600 R0001 1SAP 440 600 R0001 DC522, digital input/output module, 16

More information

Contact protection relay

Contact protection relay Contact protection relay Ordering details SVR 450 08 F0000 The protects sensitive control contacts from excessive load. It can be used with latching function or without. Bounce time of control contacts

More information

Relion 611 series. 611 series Type Test Certificate

Relion 611 series. 611 series Type Test Certificate Relion 611 series 611 series Document ID: 1MRS757466 Issued: 2016-02-22 Revision: B Product version: 2.0 Copyright 2016 ABB. All rights reserved Table of contents Table of contents Section 1 Section

More information

DC562, digital input/output module,

DC562, digital input/output module, Ordering Data DATA SHEET DC562 Digital Input/Output Module 1 Ordering Data Part No. Description Product Life Cycle Phase *) 1SAP 231 900 R0000 1TNE 968 901 R3101 1TNE 968 901 R3102 1TNE 968 901 R3103 1TNE

More information

Sensitive definite time or inverse time earth-fault stage for back-up residual earthfault

Sensitive definite time or inverse time earth-fault stage for back-up residual earthfault Issued: April 1999 Status: Updated Version: B/09.11.2001 Data subject to change without notice Features Sensitive restricted earth-fault protection stage for fast, selective earth-fault protection Sensitive

More information

DC541 Digital Input/Output Module

DC541 Digital Input/Output Module Ordering Data DATA SHEET DC541 Digital Input/Output Module 1 Ordering Data Part No. Description Product Life Cycle Phase *) 1SAP 270 000 R0001 1SAP 470 000 R0001 DC541-CM, digital input/output module,

More information

AO561 Analog Output Module

AO561 Analog Output Module Ordering Data DATA SHEET AO561 Analog Output Module 1 Ordering Data Part No. Description Product Life Cycle Phase *) 1TNE 968 902 R1201 AO561, analog output module, 2 AO, U/I 1TNE 968 901 R3102 Terminal

More information

Published by and copyright 2015 Siemens AG Energy Management Freyeslebenstr Erlangen, Germany

Published by and copyright 2015 Siemens AG Energy Management Freyeslebenstr Erlangen, Germany Published by and copyright 2015 Siemens AG Energy Management Freyeslebenstr. 1 91058 Erlangen, Germany For more information, please contact our Customer Support Center Phone: +49 180/524 84 37 Fax: +49

More information

Combined Overcurrent and Earth-fault Relay SPAJ 141 C. Product Guide

Combined Overcurrent and Earth-fault Relay SPAJ 141 C. Product Guide Combined Overcurrent and Earth-fault Product Guide Issued: April 1999 Status: Updated Version: C/19.04.2006 Data subject to change without notice Features Three-phase, low-set phase overcurrent unit with

More information

INSTRUCTION MANUAL TRIP CIRCUIT SUPERVISION RELAY GKAD1

INSTRUCTION MANUAL TRIP CIRCUIT SUPERVISION RELAY GKAD1 INSTRUCTION MANUAL TRIP CIRCUIT SUPERVISION RELAY GKAD1 TOSHIBA Corporation 2004 All Rights Reserved. ( Ver. 1.6 ) Safety Precautions Before using this product, please read this chapter carefully. This

More information

QUINT-BUFFER/24DC/24DC/40

QUINT-BUFFER/24DC/24DC/40 Buffer module Data sheet 105496_en_01 PHOENIX CONTACT 2013-11-01 1 Description The QUINT BUFFER buffer module combines the electronic switchover unit and power storage in the same housing. The buffer module

More information

Siprotec 7ST61 / 7ST63

Siprotec 7ST61 / 7ST63 Siprotec / Numerical overhead contact line protection for AC traction power supply siemens.de/rail-electrification The numerical overhead contact line protection relay Siprotec / is a selective and quick

More information

Voltage regulator. SPAU 341 C 1MRS MBG Issued: July 1998 Status: Revised Version: C/ Data subject to change without notice

Voltage regulator. SPAU 341 C 1MRS MBG Issued: July 1998 Status: Revised Version: C/ Data subject to change without notice Issued: July 1998 Status: Revised Version: C/08.10.2003 Data subject to change without notice Features Comprehensive voltage regulation for power transformers with on-load tapchangers in distribution substations

More information

DC561, digital input/output module,

DC561, digital input/output module, Ordering Data DATA SHEET DC561 Digital Input/Output Module 1 Ordering Data Part No. Description Product Life Cycle Phase *) 1TNE 968 902 R2001 DC561, digital input/output module, 16 configurable inputs/outputs,

More information

DX561 Digital Input/Output Module

DX561 Digital Input/Output Module Ordering Data DATA SHEET DX561 Digital Input/Output Module 1 Ordering Data Part No. Description Product Life Cycle Phase *) 1TNE 968 902 R2301 1TNE 968 901 R3101 DX561, digital input/output module, 8 DI

More information

AI561 Analog Input Module

AI561 Analog Input Module Ordering Data DATA SHEET AI561 Analog Input Module 1 Ordering Data Part No. Description Product Life Cycle Phase *) 1TNE 968 902 R1101 AI561, analog input module, 4 AI, U/I 1TNE 968 901 R3101 1TNE 968

More information

MINI-PS AC/10-15DC/8

MINI-PS AC/10-15DC/8 Primary-Switched Power Supply, Narrow Design Data Sheet 08/2004 MINI POWER provides: An extra narrow design, with widths of 22.5 mm, 45 mm, and 67.5 mm (0.886, 1.772, and 2.657 in.) Global use due to a

More information

Electronic timer CT-ERD.12

Electronic timer CT-ERD.12 2CDC 251 092 F0t06 a Rotary switch for the preselection of the time range b Potentiometer with direct reading scale for the fine adjustment of the time delay c U: green LED V control supply voltage applied

More information

DATASHEET. Ultra Capacitor Charger, UCC-4

DATASHEET. Ultra Capacitor Charger, UCC-4 DATASHEET Ultra Capacitor Charger, UCC-4 Easy installation Monitoring and surveillance of operation Balancing to save energy 90-450 V DC 3.5A Output Modular Ultra Capacitor system Document no.: 4921260003

More information

AO523 Analog Input Module

AO523 Analog Input Module Ordering Data DATA SHEET AO523 Analog Input Module 1 Ordering Data Part No. Description Product Life Cycle Phase *) 1SAP 250 200 R0001 1SAP 450 200 R0001 AO523, analog output module, 16 AO, U/I, 12 bits

More information

02/11/2015

02/11/2015 DIN Rail Mount 22.5 mm TU2R1 Part number 88865305 Product with 1 relays (88 865 100/103/105/115/125/135/145/155/185/503) : Replaced by the 17,5 mm range For instance : previous part number 88 865 XXX /

More information

AI531 Analog Input Module

AI531 Analog Input Module Ordering Data DATA SHEET AI531 Analog Input Module 1 Ordering Data Part No. Description Product Life Cycle Phase *) 1SAP 250 600 R0001 AI531, analog input module, 8 AI, U/I/Pt100, TC, 15 bits + sign, 4-wires

More information

ILBPB24DO32. Inline Block IO Module for PROFIBUS With 32 Digital Outputs. AUTOMATIONWORX Data Sheet 6889_en_04. Description

ILBPB24DO32. Inline Block IO Module for PROFIBUS With 32 Digital Outputs. AUTOMATIONWORX Data Sheet 6889_en_04. Description Inline Block IO Module for PROFIBUS With 32 Digital Outputs AUTOMATIONWORX Data Sheet 6889_en_04 Description PHOENIX CONTACT - 03/2007 & & ' ) The ILB PB 24 DO32 module is designed for use within a PROFIBUS

More information

Tap Position Indicator - PI

Tap Position Indicator - PI PI Catalog Tap Position Indicator - PI The Tap Position Indicator (PI) consists of a microprocessor based electronic device capable of monitoring and modifying, through the load tap changer (LTC), the

More information

FL MC 2000E (SM40) LC

FL MC 2000E (SM40) LC IEC 61850 fiber optic converter with LC fiber optic connection (1310 nm) to convert 100Base-Tx to single- or multi-mode fiber glass Data sheet 3205_en_C 1 Description PHOENIX CONTACT 2014-04-04 2 Features

More information

7SR18 Solkor Line Differential Protection Energy Management

7SR18 Solkor Line Differential Protection Energy Management Reyrolle Protection Devices 7SR18 Solkor Line Differential Protection Energy Management 7SR18 Solkor five or eight user-programmable binary output contacts and three or six user programmable status inputs

More information

Single-phase ( V) voltage monitoring: Undervoltage Overvoltage Window mode (overvoltage + undervoltage) Voltage fault memory selectable

Single-phase ( V) voltage monitoring: Undervoltage Overvoltage Window mode (overvoltage + undervoltage) Voltage fault memory selectable 70 Series - Line monitoring relay 70 Features 70.11 70.31 70.41 Electronic voltage monitoring relays for single and three-phase applications Multifunctional types, providing the flexibility of monitoring

More information

CM589 PROFINET Communication Module

CM589 PROFINET Communication Module Ordering Data DATA SHEET CM589 PROFINET Communication Module 1 Ordering Data Part No. Description Product Life Cycle Phase *) 1SAP 172 900 R0011 1SAP 372 900 R0011 1SAP 172 900 R0111 1SAP 372 900 R0111

More information

1S20. Arc Fault Monitor Relay. Features. Introduction. ARC Fault Protection

1S20. Arc Fault Monitor Relay. Features. Introduction. ARC Fault Protection Technical Bulletin Arc Fault Monitor Relay Features Compact, economic design Simple panel mounting for retrofit applications Two or three arc sensor inputs Two high speed tripping duty arc sense output

More information

CM597 Ethernet Communication Module

CM597 Ethernet Communication Module Ordering Data DATA SHEET CM597 Ethernet Communication Module 1 Ordering Data Part No. Description Product Life Cycle Phase *) 1SAP 173 700 R0001 1SAP 373 700 R0001 CM597-ETH, communication module Ethernet

More information

SIMOCODE 3UF Motor Management and Control Devices

SIMOCODE 3UF Motor Management and Control Devices Technical specifications General data applicable to the basic units, current measuring modules, current/voltage measuring modules, expansion modules, decoupling module and operator panel Permissible ambient

More information

PCD3.C90. Date Modification Asked by: Version E/A Bus Connector PCD2.K106 change to PCD3.K106 Müller.R 1.1

PCD3.C90. Date Modification Asked by: Version E/A Bus Connector PCD2.K106 change to PCD3.K106 Müller.R 1.1 Manual PCD3.C90 Revision History Date Modification Asked by: Version 14.09.09 E/A Bus Connector PCD2.K106 change to PCD3.K106 Müller.R 1.1 22.09.09 Added E/A Bus Connector PCD3.K116 Müller.R 1.2 06.01.10

More information

Feeder Protection Relay REF 610. Product Guide

Feeder Protection Relay REF 610. Product Guide Product Guide Contents 1 Description.............................. 3 2 Protection functions....................... 3 3 Measurement............................ 4 4 Disturbance recorder......................

More information

CM589 PROFINET Communication Module

CM589 PROFINET Communication Module Ordering Data DATA SHEET CM589 PROFINET Communication Module 1 Ordering Data Part No. Description Product Life Cycle Phase *) 1SAP 172 900 R0011 1SAP 372 900 R0011 1SAP 172 900 R0111 1SAP 372 900 R0111

More information

CM579-PNIO PROFINET Communication Module

CM579-PNIO PROFINET Communication Module Ordering Data DATA SHEET CM579-PNIO PROFINET Communication Module 1 Ordering Data Part No. Description Product Life Cycle Phase *) 1SAP 170 901 R0101 1SAP 370 901 R0101 CM579-PNIO, PROFINET communication

More information

Generator Protection. Page

Generator Protection. Page Generator Protection Page SIPROTEC 4 7UM61 Multifunction Generator and Motor Protection Relay /3 SIPROTEC 4 7UM62 Multifunction Generator, Motor and Transformer Protection Relay /33 SIPROTEC 7UW50 Tripping

More information

Reyrolle Protection Devices. 7SG117 Argus 7 Synchronising Relay. Answers for energy

Reyrolle Protection Devices. 7SG117 Argus 7 Synchronising Relay. Answers for energy Reyrolle Protection Devices 7SG117 Argus 7 Synchronising Relay Answers for energy 7SG117 Argus 7 Synchronising Relay Fig 1. Independent check & system synchronising settings Adjustable slip frequency,

More information

CD522 Encoder, Counter and PWM Module

CD522 Encoder, Counter and PWM Module Ordering Data DATA SHEET CD522 Encoder, Counter and PWM Module 1 Ordering Data Part No. Description Product Life Cycle Phase *) 1SAP 260 300 R0001 1SAP 460 300 R0001 CD522, encoder & PWM module, 2 encoder

More information

PHOENIX CONTACT - 01/2010. Features. DANGER OF EXPLOSION! Only remove equipment when it is disconnected and not in the potentially explosive area.

PHOENIX CONTACT - 01/2010. Features. DANGER OF EXPLOSION! Only remove equipment when it is disconnected and not in the potentially explosive area. Uninterruptible power supply with integrated power supply unit INTERFACE Data sheet 104211_en_00 1 Description PHOENIX CONTACT - 01/2010 Features The MINI-DC-UPS provide an uninterruptible DC voltage both

More information

Electronic timer CT-ERS.12 ON-delayed with 1 c/o contact Data sheet

Electronic timer CT-ERS.12 ON-delayed with 1 c/o contact Data sheet 2CDC 251 056 F0t07 Features Rated control supply voltage 24-48 V DC, 24-240 V AC Single-function ON-delay timer One device includes 10 time ranges (0.05 s - 300 h) 1 c/o contact 2 LEDs for status indication

More information

AX522 Analog Input/Output Module

AX522 Analog Input/Output Module Ordering Data DATA SHEET AX522 Analog Input/Output Module 1 Ordering Data Part No. Description Product Life Cycle Phase *) 1SAP 250 000 R0001 1SAP 450 000 R0001 AX522, analog input/output module, 8 AI

More information

XE2 DC current relay for loss of excitation protection. Manual XE2 (Revision A)

XE2 DC current relay for loss of excitation protection. Manual XE2 (Revision A) XE2 DC current relay for loss of excitation protection Manual XE2 (Revision A) Woodward Manual XE2 GB Woodward Governor Company reserves the right to update any portion of this publication at any time.

More information

XU1-E Earth fault voltage relay. (August 1996) Manual XU1-E (Revision New)

XU1-E Earth fault voltage relay. (August 1996) Manual XU1-E (Revision New) XU1-E Earth fault voltage relay (August 1996) Manual XU1-E (Revision New) Woodward Manual XU1-E GB Woodward Governor Company reserves the right to update any portion of this publication at any time. Information

More information

ILBIB24DO16-DSUB. Inline Block IO Module for INTERBUS With 16 Digital Outputs; Bus Connection via D-SUB Connectors

ILBIB24DO16-DSUB. Inline Block IO Module for INTERBUS With 16 Digital Outputs; Bus Connection via D-SUB Connectors Inline Block IO Module for INTERBUS With 16 Digital Outputs; Bus Connection via D-SUB Connectors AUTOMATIONWORX Data Sheet 7119_en_02 PHOENIX CONTACT - 03/2007 Description The ILB IB 24 DO16-DSUB module

More information

CI542 PROFIBUS Communication Interface Module

CI542 PROFIBUS Communication Interface Module Ordering Data DATA SHEET CI542 PROFIBUS Communication Interface Module 1 Ordering Data Part No. Description Product Life Cycle Phase *) 1SAP 224 200 R0001 1SAP 424 200 R0001 CI542-DP, PROFIBUS DP bus module,

More information

PHOENIX CONTACT - 01/2007

PHOENIX CONTACT - 01/2007 Uninterruptible power supply INTERFACE Data Sheet 103123_00_en PHOENIX CONTACT - 01/2007 Description Especially compact and easy-to-use, the new MINI-DC-UPS/ 24 DC/2 is a combination of the power supply

More information

CI504 PROFINET Communication Interface Module

CI504 PROFINET Communication Interface Module Ordering Data DATA SHEET CI504 PROFINET Communication Interface Module 1 Ordering Data Part No. Description Product Life Cycle Phase *) 1SAP 221 300 R0001 1SAP 421 300 R0001 CI504-PNIO, PROFINET Bus Module

More information

Output Voltage* (nom.)(adjustable)

Output Voltage* (nom.)(adjustable) Industrial Power Supplies TBLC Series, 6 90 W Low profile case, module depth only 55 mm Suitable for mounting in domestic installation panels Very high efficiency and low standby power -> compliance to

More information

Relion 605 series. Self-powered feeder protection REJ603 Product Guide

Relion 605 series. Self-powered feeder protection REJ603 Product Guide Relion 605 series Relion 605 series Relion 605 series Self-powered feeder protection Product Guide Product version: 3.0 Contents 1. Description... 3 2. Relay functions... 3 3. Protection functions... 4

More information

Electronic timer CT-ERS.21

Electronic timer CT-ERS.21 2CDC 251 057 F0t07 Features Rated control supply voltage 24 240 V AC/DC Single function ON delay timer One device includes 10 time ranges (0.05 s 300 h) 2 c/o contacts 2 LEDs for status indication Width

More information

FEATURES DESCRIPTION FEATURES

FEATURES DESCRIPTION FEATURES FEATURES Two High Speed Counters Two Pulse Train Outputs Two Pulse Width Modulation Outputs 24 Sinking or Sourcing Inputs 16 Outputs 1 RS232 Port 2 RS485 Ports Supports Modbus RTU Protocol Communicate

More information

DC532-XC, digital input/output module,

DC532-XC, digital input/output module, Ordering Data DATA SHEET DC532 Digital Input/Output Module 1 Ordering Data Part No. Description Product Life Cycle Phase *) 1SAP 240 100 R0001 1SAP 440 100 R0001 DC532, digital input/output module, 16

More information

PDD-300 pulsed diode driver

PDD-300 pulsed diode driver rev 1.08 / 2019 02 13 PDD-300 pulsed diode driver User manual Warning! This equipment may be dangerous. Please read user manual before starting operations. Important note. Please measure output with adequate

More information

Solid-state Timer H3YN

Solid-state Timer H3YN Solid-state Timer H3YN Miniature Timer with Multiple Time Ranges and Multiple Operating Modes Minimizes stock. Pin configuration compatible with MY Power Relay. Standard multiple operating modes and multiple

More information

ekorrps MULTIFUNCTIONAL PROTECTION UNIT CONFIGURATION AND GENERAL CHARACTERISTICS LIB

ekorrps MULTIFUNCTIONAL PROTECTION UNIT CONFIGURATION AND GENERAL CHARACTERISTICS LIB MO-067-EN Operation Manual MULTIFUNCTIONAL PROTECTION UNIT CONFIGURATION AND GENERAL CHARACTERISTICS LIB Transformer Substations Secondary Distribution Switchgear Primary Distribution Switchgear Protection

More information

PHOENIX CONTACT - 07/2006

PHOENIX CONTACT - 07/2006 Buffer module with maintenance-free capacitor-based power storage device INTERFACE Data sheet 102035_03_en PHOENIX CONTACT - 07/2006 Description Short-term mains interruptions are bridged by QUINT BUFFER,

More information

GFK-2415A March Type of sensor connection

GFK-2415A March Type of sensor connection VersaMax IP Expansion Module has four analog differential inputs that can be configured as current or voltage inputs. It connects to a local bus that is interfaced to a Profibus-DP / PROFINET network by

More information

CM592 PROFIBUS Communication Module

CM592 PROFIBUS Communication Module Ordering Data DATA SHEET CM592 PROFIBUS Communication Module 1 Ordering Data Part No. Description Product Life Cycle Phase *) 1SAP 173 200 R0001 1SAP 373 200 R0001 CM592-DP, communication module PROFIBUS

More information

Bus Bar Protection Relay B-PRO 4000

Bus Bar Protection Relay B-PRO 4000 Bus Bar Protection Relay B-PRO 4000 Product Overview The IEC 61850 station bus embedded B-PRO 4000 relay provides complete bus and substation differential protection (low impedance) with CT saturation

More information

Electronic timer CT-APS.21 OFF-delayed with 2 c/o (SPDT) contacts

Electronic timer CT-APS.21 OFF-delayed with 2 c/o (SPDT) contacts Data sheet Electronic timer CT-APS.21 OFF-delayed with 2 c/o (SPDT) contacts The CT-APS.21 is an electronic timer from the CT-S range with OFF-delay. It provides 10 time ranges and a continuous rated control

More information

TM221M16R controller M IO relay

TM221M16R controller M IO relay Product data sheet Characteristics TM221M16R controller M221 16 IO relay Complementary Main Discrete I/O number 16 Number of I/O expansion module Supply voltage limits Inrush current Power consumption

More information

TM221CE40T controller M IO transistor PNP Ethernet

TM221CE40T controller M IO transistor PNP Ethernet Product data sheet Characteristics TM221CE40T controller M221 40 IO transistor PNP Ethernet Complementary Main Discrete I/O number 40 Number of I/O expansion module Supply voltage limits Inrush current

More information

Type MVTT 14 and MVTT 15: Static Digital Time delay relays

Type MVTT 14 and MVTT 15: Static Digital Time delay relays Type MVTT 4 and MVTT 5: Static Digital Time delay relays Features 000/ setting range Time settings easily selected by means of thumbwheel switches Provide time delayed pick-up, or drop-off Compact construction

More information

PHOENIX CONTACT - 08/2009. Features. DANGER OF EXPLOSION! Only remove equipment when it is disconnected and not in the potentially explosive area.

PHOENIX CONTACT - 08/2009. Features. DANGER OF EXPLOSION! Only remove equipment when it is disconnected and not in the potentially explosive area. Primary-switched power supply for building automation INTERFACE Data sheet 103505_en_02 1 Description PHOENIX CONTACT - 08/2009 Features STEP POWER power supply units for building automation The new STEP

More information

08/07/2015

08/07/2015 DIN Rail Mount 22.5 mm TUR1 Part number 88865105 Product with 1 relays (88 865 100/103/105/115/125/135/145/155/185/503) : Replaced by the 17,5 mm range For instance : previous part number 88 865 XXX /

More information

AX521 Analog Input/Output Module

AX521 Analog Input/Output Module Ordering Data DATA SHEET AX521 Analog Input/Output Module 1 Ordering Data Part No. Description Product Life Cycle Phase *) 1SAP 250 100 R0001 1SAP 450 100 R0001 AX521, analog input/output module, 4 AI,

More information

TM221CE24R controller M IO relay Ethernet

TM221CE24R controller M IO relay Ethernet Product data sheet Characteristics TM221CE24R controller M221 24 IO relay Ethernet Complementary Main Discrete I/O number 24 Number of I/O expansion module Supply voltage limits Network frequency Inrush

More information

Thermistor motor protection relays CM-MSS.22 and CM-MSS.23

Thermistor motor protection relays CM-MSS.22 and CM-MSS.23 Data sheet Thermistor motor protection relays CM-MSS.22 and CM-MSS.23 The thermistor motor protection relays CM-MSS.22 and CM-MSS.23 monitor the winding temperature of motors and protect them from overheating,

More information

Millenium 3. General Characteristics. General environment characteristics for CB, CD, XD, XR and XE product types

Millenium 3. General Characteristics. General environment characteristics for CB, CD, XD, XR and XE product types Millenium 3 General Characteristics Millenium 3 Compact Range Millenium 3 Expandable Range Millenium 3 Communication Options Millenium 3 Range General environment characteristics for CB, CD, XD, XR and

More information

TM221M16TG controller M IO transistor PNP spring

TM221M16TG controller M IO transistor PNP spring Characteristics controller M221 16 IO transistor PNP spring Main Range of product Product or component type [Us] rated supply voltage Discrete input number Analogue input number Discrete output type Discrete

More information

Electronic timer CT-SDD.22 Star-delta change-over with 2 n/o contacts

Electronic timer CT-SDD.22 Star-delta change-over with 2 n/o contacts Data sheet Electronic timer CT-SDD. Star-delta change-over with n/o contacts The CT-SDD. is an electronic time relay with star-delta change-over. It is from the CT-D range. With their MDRC profile and

More information

RM4TA32 three-phase network control relay RM4-T - range V

RM4TA32 three-phase network control relay RM4-T - range V Characteristics three-phase network control relay RM4-T - range 380..500 V Complementary [Us] rated supply voltage Output contacts Main Range of product Product or component type Relay type Product specific

More information