Power Products. Station Automation COM600 Product Guide
|
|
- Sharleen Parsons
- 5 years ago
- Views:
Transcription
1 Power Products Station Automation Product Guide
2 Contents Application Parameter setting Event and alarm lists Disturbance record handling Data historian Logic processor Access control and substation security Substation integration Integration of ABB IEDs Commissioning and troubleshooting Communication redundancy Technical data Tools Mounting Ordering References Disclaimer The information in this document is subject to change without notice and should not be construed as a commitment by ABB Oy. ABB Oy assumes no responsibility for any errors that may appear in this document. Copyright 2009 ABB Oy All rights reserved. Trademarks ABB is a registered trademark of ABB Group. All other brand or product names mentioned in this document may be trademarks or registered trademarks of their respective holders. 2 ABB
3 1., the station automation device of ABB, is an all-in-one communication gateway, automation platform and user interface solution for utility and industrial distribution substations. The gateway functionality provides seamless connectivity between substation IEDs and network-level control and management systems. The automation platform with its logic processor makes a flexible implementation platform for substation-level automation tasks. As a user interface solution accommodates web technology based functionalities providing access to substation devices and processes via a web browser based human machine interface (HMI). The design process has been guided by the IEC standard for communication and interoperability of substation equipment. The communication gateway functionality of supports a variety Issued: January 2009 Revision: B / 23 Oct 2009 of commonly used communication protocols of substation devices. For even greater connectivity, OPC data access and OPC alarms and events are supported to enable information sharing and control with, for example, a distributed control system (DCS). The IEC based logic processor can be programmed to execute automatic sequences directly via communications media. Further, the logic processor enables the creation of both simple control programs and more sophisticated applications like load shedding or fault isolation and network restoration. The hardware platform is based on ruggedized mechanics with no moving parts subject to wear and tear. Thus, the compact and robust design is well adapted for harsh environments. The preinstalled software and the off-line configuration performed on a separate computer contribute to a faster project execution. Standard web-browser On-line operation REMOTE CONTROL Configuration tool on a PC Conf Web server HMI application OPC Client DNP3 Slave OPC Client Configuration phase, off-line Connectivity packages for ABB IEDs and/or device profiles SCL Fig. 1 Station Automation overview OPC Server IEC IEC REF 542plus REF 543 REF615 ABB 3
4 2. Application provides gateway functions for mapping signals between protection and control IEDs in industrial or utility substations and higher-level systems. It further includes an optional HMI that provides data and information from the substation to the users. gathers data from protection and control IEDs and from process devices using different communication protocols. The supported protocols can be combined freely in one station computer, limited only by the number of hardware interfaces and the license. uses web technology to display data to different users in a professional and user-friendly manner. The optional slave protocols enable the transfer of information to a network control centre (NCC) or distributed control system (DCS). benefits from the potential of the IEC standard by using the IEC substation configuration language (SCL) and IEC communications modeling regardless of protocol used. As the IEC data modeling is used for all communication protocols the gateway cross-reference is done in the same way regardless of the protocol, for example IEC or DNP3. can by using the optional web HMI (requires Mozilla Firefox, Opera or Microsoft Internet Explorer with Adobe SVG viewer 3.03) be used for efficient substation visualization, monitoring and control. Measured values from process devices are displayed on the HMI. Single-line diagrams can be used to view any available measured values from the process devices. All primary single-line diagram (SLD) devices are displayed in one screen. The SLD recognizes different voltage levels and different busbar systems such as single busbar, double busbar and duplex systems. The four-mode busbar coloring visualizes the busbar status. The coloring of the busbar is user configurable. EMS/ SCADA DMS, OMS REMOTE ACCESS - ENGINEERING GPS TCP/IP protocols (DNP3, IEC , Modbus) WAN Serial protocols (DNP3, IEC , Modbus) LAN 1 SPAJ 140 LON-bus RER 111 TCP/IP protocols (IEC 61850, DNP3, Modbus ) RTU/PLC Serial protocols (DNP3, Modbus, SPA) REM 543 RTU/PLC REF 542plus REF 543 REF615 NON-ABB IED REF 542plus DPU2000R Fig. 2 Overview of a utility substation using Station Automation REF615 NON-ABB IED 4 ABB
5 DISTRIBUTED CONTROL SYSTEM REMOTE ACCESS - ENGINEERING OPC Client/Server WAN GPS LAN 1 SPAJ 140 LON-bus RER 111 TCP/IP protocols (IEC 61850, DNP3, Modbus ) RTU/PLC Serial protocols (DNP3, Modbus, SPA) REM 543 RTU/PLC REF 542plus REF 543 REF615 NON-ABB IED REF 542plus DPU2000R Fig. 3 Overview of an industrial system using Station Automation REF615 NON-ABB IED The single line diagram can be configured to include an indication for the local/remote selection switch. Alarm symbols and generic symbols can be places in the SLD to give an even better overview of the status. In addition, generic control buttons can be added to control objects. A separate control dialog is used for controlling the switching device. It provides information on switching device identification, reservation status and interlocking conditions. The select-before-execute logic is used to prevent unintended operation. By reserving the switching device for a single user the risk of controlling the device from two different locations is eliminated. Further, supports the tap changer function for the RE 500 series transformer terminals. Connection examples: has by default four serial ports. The number of serial ports can be increased using the optional serial card. The four serial ports enable the connection and combination of different serial protocols. For example 3 SPA + 1 IEC 101 protocol or 2 SPA + 1 IEC IEC 101 protocol. can as an option be equipped with a LON-card enabling the connection of one plastic or glass LON interface. Alternatively the number of Ethernet interfaces can be increased by choosing the optional Ethernet extension card. 3. Parameter setting The parameter setting tool (PST) is used for viewing and/or setting parameters in IEDs supporting transparent SPA, Modbus or IEC parameterization. The PST enables activation of the parameter setting function for the chosen IEDs. In addition, it enables that only selected parameters are shown in ABB 5
6 GPS Web HMI LAN 1 LAN 2 RS-232/RS-485 serial links 1-8 link 1 link 8 Fig. 4 Application example IED IED the web HMI of limiting the number of visible parameters to the ones that are considered important for the user. Changes in the settings require that the user has engineering or administrator rights in. 4. Event and alarm lists disturbance records are saved in the standard COMTRADE format. In-depth analysis is enabled using ABB s Wineve software or any other commercially available disturbance record analyzer supporting the COMTRADE format. Downloading of disturbance records requires use of the IEC communication protocol. Events and alarms are identified by date, time, bay, device, object description or status. Furthermore, the events and alarms can be automatically filtered according to voltage level or bay criteria. Maximum memory capacity is events. First-in, first-out logic is used for overwriting events. The user can export an event list to a.csv file for further analysis. supports printing of events to an Event Printer for long time archiving. 5. Disturbance record handling automatically downloads disturbance records from the connected IEDs. The 6. Data historian The data historian is a real-time database designed and optimized for process information management and extensive history recording. The data historian is based on ABB s cpmplus Knowledge Manager software. It combines the benefits of an easy-to-use real-time database with industrial reliability, performance, and real-time functionality to provide an excellent platform for process information management. The data historian can be used for accurate process performance monitoring by following process and equipment performance calculations with real-time and history values. Better understanding of the process behaviour by joining time-based process measurements with production and maintenance events helps 6 ABB
7 Station Automation Fig. 5 web HMI showing persisting and fleeting alarms Fig. 6 Data historian ABB 7
8 the user to understand the process dynamics. It further provides required information for learning how to keep the process running. High performance and reliability, together with maintenance-free operation, provide a solid platform for trending. The optional data historian functionality offers means of storing, analyzing and presenting process data. Please note that displaying of data historian information using the HMI requires that Microsoft Internet Explorer is used. off-line functionality for engineering and diagnostics. The logic process can be used for applications such as grouping of signals or tripping of all bus breakers, if one of the breakers fails to clear the fault. collects any analog or binary IED data using standard serial and TCP/IP based protocols such as IEC 61850, DNP3 or Modbus. In the created logic, the logic processor, use the analog and binary data from the IEDs. The output of the created logic can be sent to the IEDs for tripping or alarm purposes. 7. Logic processor offers an straightforward approach to the languages specified by the IEC standard for programmable logic controllers (PLC). The programmable logic processor in is offered as a selectable software option. The PLC programming system enables programming and execution of automation tasks. In addition, the IEC programming in offers on-line and 8. Access control and substation security To protect from unauthorized access and to maintain information integrity, is provided with a four-level, rolebased authentication system with administrator-programmable individual passwords for the viewer, operator, engineer and admin- EMS/ SCADA WAN ENGINEERING ELECTRONIC SECURITY PERIMETER GPS Built-in firewall LAN 1 SPAJ 140 LON-bus RER 111 TCP/IP protocols (IEC 61850, DNP3, Modbus ) RTU/PLC Serial protocols (DNP3, Modbus, SPA) REM 543 RTU/PLC REF 542plus REF 543 REF615 NON-ABB IED REF 542plus DPU2000R REF615 NON-ABB IED Fig. 7 Substation security 8 ABB
9 PLANT TCP/IP OPC Client/Server LOCAL HMI DISTRIBUTION CONTROL SYSTEM GPS 7.2 kv 0.4 kv MLink REF615 REF615 REF615 REF615 FEEDER 1 FEEDER 2 FEEDER 3 7.2/0.4 kv M M M Fig. 8 Substation integration istrator level. Further, the security features include host-based firewalls and communication encryption using the secure HTTPS (hypertext transfer protocol secure) protocol. 9. Substation integration provides connectivity to a range of ABB systems. The connectivity to ABB s low voltage motor control center MNS is is provided using an OPC server in. receives data from the MNSiS devices and provides a human-machine interface (HMI) and gateway functionality for a smooth integration. Further, offers connectivity to ABB s Automation System 800xA and MicroSCADA by means of OPC or other communication protocols. 10. Integration of ABB IEDs supports ABB s connectivity package concept which simplifies system configuration and integration of IEDs. A connectivity package is a collection of software and specific IED information, which enable system products and tools to connect and interact with the IED. The connectivity packages reduce the risk of errors in system integration, minimizing device configuration and set-up times. The engineering in is done by selecting the connectivity package for the IED version and configuration or by importing the configuration file from the IED. 11. Commissioning and troubleshooting offers several tools and functions to support efficient commissioning and trou- ABB 9
10 bleshooting of the substation. The built-in IED simulation functionality enables testing and verifying of the correct operation of the HMI and gateway configuration of without any physical connection of IEDs. Further, communication diagnostic events can be enabled to track all messages being sent by or received from the IEDs. Using the Station Automation Builder 600 (SAB600) tool provided with online diagnostic data, real-time process data, the communication channels and the control function of the IEDs can be analyzed without separate protocol analyzers. 12. Communication redundancy To maintain and improve the reliability of the communication network and the communication between the IEDs and, IEC 62439/PRP (parallel redundancy protocol)- based communication is supported. PRP is based on duplicated networks, where each message is sent via both networks. The first of the received messages is accepted whereas the duplicate is discarded. Message replication and discarding is done by the DuoDriver in. Further, the DuoDriver hides the two networks from upper level applications. IEC 62439/PRP-based communication requires that is equipped with the optional LAN card and that the IEDs used support PRP. In addition, supports switch fault tolerance (SFT) provided that the optional LAN-card and are connected to two separate switches. SFT creates a failover relationship between the two adapters connected to separate switches. The manager responsibility is transferred from one agent to the other in case of a failure. The Switch Fault Tolerance feature of the Intel network adapter requires the Teaming Feature to be enabled. Web HMI Simulation of complete IEDs Source data monitoring Forcing of source data SCADA TCP/IP protocols (IEC 61850, DNP3, Modbus ) Web server HMI application OPC Client DNP3 Slave OPC Client REF 542plus REF 543 REF615 OPC Server IEC Fig. 9 Commissioning and troubleshooting 10 ABB
11 13. Technical data Table 1. Dimensions Width Height Depth Weight Value 214 mm (243 mm with mounting kit) 122,4 mm (129.4 mm with mounting kit) 313 mm 6.8 kg Table 2. Power supply U aux nominal U aux variation Power consumption Power consumption at start-up Value V DC V AC ( Hz) % of U n ( V DC) % of U n ( V AC) 37 W (with 264 V DC) 220 W Table 3. Hardware Processor System memory Compact flash memory Value Intel Pentium M 1.6 GHz 1 GB SDRAM 8 GB industrial SSD Table 4. Interfaces Serial interfaces Serial interface Ethernet interfaces USB Value 3 x RS-232 interfaces 1 x RS-232/485 serial interface 2 x 10/100Base-TX RJ-45 interfaces 4 x USB 2.0 interfaces Table 5. Optional PCI extensions LON interface 1) Serial interfaces 2) Ethernet interfaces 3) 1) Operating temperature 0 C C 2) Operating temperature 0 C C 3) Operating temperature 0 C C Value 1 x 1 LON interface 8 x RS-232/485 serial interfaces 2 x 10BASE-T/100BASE-TX/1000BASE-T RJ-45 interfaces ABB 11
12 Table 6. Inspection of mechanical structure Standard Markings and mechanical structure According to IEC , -6 Degree of protection by enclosure According to IEC Clearance and creepage distances According to IEC Table 7. Power supply and module tests Standard Auxiliary voltage According to IEC Aux. voltage interruptions According to IEC Ripple in auxiliary DC voltage According to IEC %, f = 2 x fn Power consumption According to CE EN Table 8. Insulation tests Standard Dielectric test According to IEC kv, 50 Hz for 1 minute Impulse voltage test According to IEC kv, 1.2/50 μs, 0.5 J Insulation resistance According to IEC >100 MΩ, 500 Vdc Protective bonding impedance According to IEC <0.1 Ω. Table 9. Electromagnetic compatibility tests The EMC immunity test level meets the requirements listed below: 1 MHz burst disturbance test Common mode Differential mode Standard According to IEC and IEC kv 1.0 kv 12 ABB
13 Electrostatic discharge test Contact discharge Air discharge According to IEC , IEC kv 8 kv Radio frequency field immunity According to IEC and IEC V/m (80% amp.mod.) f= MHz 10 V/m (pulse mod.) f=900 MHz Fast transient Power supply RJ-45 port Surge immunity Power supply According to IEC and IEC kv 1 kv According to IEC and IEC kv line-to-earth, 1 kv line-to-line Conducted radio frequency disturbance According to IEC and IEC V (80% ampl. mod.) f= 150 khz...80 MHz Power frequency (50 Hz) magnetic field According to IEC , 300 A/m, continuous Voltage dips and short interruptions According to IEC % reduction for 10 ms 60% reduction for 100 ms 60% reduction for 1000 ms >95% reduction for 5000 ms Emission tests According to EN 55011, and IEC , class A Table 10. Environmental conditions Value Operating temperature range ºC Relative humidity range, non-condensing 1) 2) % at +40ºC Storage temperature ºC 1) Without any option cards 2) With Ethernet option card: C, with Serial option card: C, with LON option card: C ABB 13
14 Table 11. Environmental tests Standard Dry heat test According to IEC Test values: 96 h at +55ºC 4 h at +70ºC Cold test According to IEC Test values: 96 h at -10ºC 4 h at -25ºC Damp heat test, cyclic According to IEC Test values: 6 cycles (12+12h) at C, humidity >93% Storage test According to IEC Test values: 72 h at +70ºC 72 h at -40ºC Table 12. Mechanical tests Vibration tests Vibration response test Vibration endurance test Shock and bump tests Shock response test Shock withstand test Bump test Standard According to IEC and IEC f = Hz, ± mm, Hz, 5 m/s Hz f = Hz, ± mm, Hz, 10 m/s Hz According to IEC , IEC and IEC peak acceleration = 5 x gn, pulse duration = 11 ms, numbers of pulses in each diretion = 3 peak acceleration = 15 x gn, pulse duration = 11 ms, number of pulses in each direction = 3 peak acceleration = 10 x gn, pulse duration = 16 ms, number of pulses in each direction = ABB
15 Seismic test biaxial multi-frequency random seismic test According to IEC test method B 2 x gn in horizontal direction, 1 x gn in vertical direction Table 13. EMC compliance Complies with the EMC directive 2004/108/EC Standards EN (2000), EN (2007) EN (2005) EN (2007) Table 14. Product safety Complies with the LV directive 2006/95/EC Standards EN (2005), EN (1994) Table 15. RoHS compliance Complies with the RoHS directive 2002/95/EC Table 16. Communication protocols Master protocol Slave protocol DNP3 LAN/WAN DNP3 LAN/WAN DNP3 serial DNP3 serial IEC IEC IEC IEC IEC External OPC IEC SPA router LON LAG Modbus serial TCP MNS is Connectivity Modbus serial Modbus TCP SPA ABB 15
16 Table 17. IEDs with connectivity packages supporting 610 series IEDs Feeder Protection REF610 Motor Protection REM610 Voltage Protection REU series IEDs Feeder Protection Relay REX 521 SPAJ 140 series relays Combined Overcurrent and Earth-fault Relay SPAJ 140 C Combined Overcurrent and Earth-fault Relay SPAJ 141 C Combined Overcurrent and Earth-fault Relay SPAJ 142 C Combined Phase and Neutral Overcurrent Relay SPAJ 144 C Stabilized Differential Relay SPAD 346 C SACO 16D series units Digital Annunciator Unit SACO 16D1 Digital Annunciator Unit SACO 16D3 Digital Annunciator Unit SACO 64D4 RE 500 series terminals Feeder Terminal REF 541 / 543 / 545 Transformer Terminal RET 541/ 543 / 545 Motor and Generator Terminal REM 543 / 545 Feeder Terminal REF 542plus Table 18. Hardware requirements for SAB600 Hardware Minimum Recommended Free hard disk space 1 Gb 1.5Gb Table 19. Supported operating systems 1) Microsoft Windows 2000, Windows XP Professional Edition SP2 or later, Windows 2003 Server, Vista, Vista Server ) Microsoft.NET Framework 2.0 is required for running SAB600. The software is automatically installed during the installation of SAB600 if not already available on the PC. Table 20. Supported web browsers (Web HMI) Microsoft Internet Explorer (with Adobe SVG viewer 3.03) Version 6.0 or later Mozilla Firefox 3.0 Opera 9 16 ABB
17 14. Tools Engineering of is done offline on a separate computer using the Microsoft.NETbased SAB600 engineering tool supplied with. The configurability and functionality of depends on the communication protocol used for communication between and the IEDs. The connectivity packages for ABB s protection and control IEDs enable an efficient configuration of. The connectivity packages include descriptions of the data and signals available in the IEDs. The descriptions are used to automatically configure the master communication of. At project engineering SAB600 uses the potential of the IEC standard by supporting the IEC based SCL (Substation Configuration Language) file import, including the import of the communication and graphical parts of the SCL-file. The finalized projects are updated from SAB600 to at site or remotely provided that a secure Ethernet connection is available. Table 21. Tools Version Station Automation Builder Mounting included wall-mount kit. The is fastened using the four holes on the unit and four screws. The computer is designed for mounting into a control panel by using the Fig. 10 Top view Fig. 11 Side view ABB 17
18 16. Ordering hardware and software modules of the unit. Use the ordering key information in Fig. 12 to generate the order number when ordering. The type and serial number label identifies the units. The order number consists of a string of code generated from the C O M H R H 3 2 P B # DESCRIPTION 1 Power supply V DC, V AC H 2 Optional communication cards (PCI) LON card, PCLTA-20, plastic fibre, 1 port P LON card, PCLTA-20, glass fibre, 1 port G Ethernet card (RJ-45) 10Base-T, 100Base-TX, 1000Base-T, 2 ports R Serial RS-232/RS-485 card, 8 ports S None N 3 HMI Web HMI H None N 4 Master protocols One master protocol 1 Two master protocols 2 Three master protocols 3 5 Slave protocols One slave protocol 1 Two slave protocols 2 None N 6 Optional software Data historian 1) T Logic processor L Data historian and Logic processor 1) P None N 7 Version Version 3.4 B 1) Requires Web HMI and Internet Explorer 6.0 or later Fig. 12 Ordering key for Station Automation 18 ABB
19 Example code: C O M H R H 3 2 P B Your ordering code: Digit (#) Code: C O M Fig. 13 Your ordering code 17. References The portal offers you information about the distribution automation product and service range. You will find the latest relevant information on the unit on the product page. The download area on the right hand side of the web page contains the latest product documentation, such as user s guide, operator s guide, etc. The selection tool on the web page helps you find the documents by the document category and language. The Features and Application tabs contain product related information in a compact format. Fig. 14 Product page ABB 19
20 Contact us ABB Oy Distribution Automation P.O. Box 699 FI VAASA, Finland Phone Fax ABB Inc. Distribution Automation 655 Century Point Lake Mary, Florida, U.S.A. Phone Fax Copyright 2009 ABB. All rights reserved.
Power Products. Station Automation COM600 Product Guide
Power Products Station Automation Product Guide Contents 1.... 3 2. Application... 4 3. Parameter setting... 5 4. Event and alarm lists...6 5. Disturbance and fault record handling... 6 6. Data historian...
More informationCommunication Gateway COM 610. Product Guide
Communication Gateway COM 610 Product Guide Issued: September 2004 Status: Updated Version: D/17.10.2006 Data subject to change without notice Features Protocol conversion gateway for substation automation:
More informationPower Products. Protection and Control IED Manager PCM600 Product Guide
Power Products Protection and Control IED Manager Product Guide Contents 1. Description............................ 3 2. Tool variants........................... 3 3. Connectivity packages...................
More informationGrid Automation Controller COM600 How it fits into the Smart Grid?
ABB Oy Distribution Automation Grid Automation Controller How it fits into the Smart Grid? May 27, 2014 Slide 1 1MRS756763 E Content Technical Presentation May 27, 2014 Slide 2 Description Grid Automation
More informationSPA-ZC 302. Profibus-DPV1/SPA Gateway. Product Guide. spa-zc302_rightco300
Profibus-DPV1/SPA Gateway SPA-ZC 302 Product Guide spa-zc302_rightco300 Issued: 25.11.2003 Status: Updated Version: D/16.05.2008 Data subject to change without notice Features Profibus DP Version 1 connectivity
More informationRelion 611 series. 611 series Type Test Certificate
Relion 611 series 611 series Document ID: 1MRS757466 Issued: 2016-02-22 Revision: B Product version: 2.0 Copyright 2016 ABB. All rights reserved Table of contents Table of contents Section 1 Section
More informationRemote I/O RIO600 Product Guide
Product Guide Contents 1. Description...3 2. Design...3 3. Configuration examples...4 4. Self-supervision...5 5. Communication...5 6. Indication LEDs...5 7. Technical data...6 8. Connection and terminal
More informationSensitive Earth-fault Relay SPAJ 111 C. Product Guide
Issued: April 1999 Status: Update Version: C/12.04.2006 Data subject to change without notice Features Sensitive low-set neutral overcurrent stage with definite time characteristic High-set neutral overcurrent
More informationArc protection relay. Features Three-phase overcurrent function. Application
Arc protection relay REA 10_ Page 1 Issued: May 1999 Status: New Data subject to change without notice Features Three-phase overcurrent function Loop-type or radial sensor fibre for arc detection Two high-speed
More informationEarth-fault Relay SPAJ 110 C. Product Guide
Issued: April 1999 Status: Updated Version: C/12.04.2006 Data subject to change without notice Features Low-set neutral overcurrent stage with definite time or inverse time characteristic High-set neutral
More informationVoltage regulator. SPAU 341 C 1MRS MBG Issued: July 1998 Status: Revised Version: C/ Data subject to change without notice
Issued: July 1998 Status: Revised Version: C/08.10.2003 Data subject to change without notice Features Comprehensive voltage regulation for power transformers with on-load tapchangers in distribution substations
More informationCombined Overcurrent and Earth-fault Relay SPAJ 140 C. Product Guide
Combined Overcurrent and Earth-fault Product Guide Issued: April 1999 Status: Updated Version: C/18.04.2006 Data subject to change without notice Features Three-phase, low-set phase overcurrent unit with
More informationextending the boundaries of technology evolution of proven technology FEATURES
extending the boundaries of technology evolution of proven technology FEATURES IEC 61850 compliant Advanced AC capabilities with comprehensive fault detection Integrated protection functions Disturbance
More informationBus Bar Protection Relay B-PRO 4000
Bus Bar Protection Relay B-PRO 4000 Product Overview The IEC 61850 station bus embedded B-PRO 4000 relay provides complete bus and substation differential protection (low impedance) with CT saturation
More informationFeeder protection relay SPAA 121 C. Product Guide
Issued: April 1999 Status: Updated Version: C/06.03.2006 Data subject to change without notice Features Two-phase low-set phase overcurrent unit with definite time or inverse time characteristic Two-phase
More informationProtection and Control IED Manager PCM600 Product Guide
Product Guide Contents 1. Description...3 2. Project explorer...4 3. Parameter setting...4 4. Graphical application configuration...4 5. Signal matrix...5 6. Graphical display editor...5 7. Hardware configuration...6
More informationArc protection relay. Features Three-phase overcurrent function. Application
Arc protection relay REA 10_ Issued: May 1999 Status: Updated Version: B/12.11.2001 Data subject to change without notice Features Three-phase overcurrent function Loop-type or radial sensor fibre for
More informationType VRLTC tap changer
Report No. 1ZUA938502-AGC 2, Rev 0 Date: 6 November 2012 Type VRLTC tap changer Ruggedized electronics systems specification & type test data Product Style No Rating By Type VRLTC, on-tank, vacuum reactance
More informationSensitive definite time or inverse time earth-fault stage for back-up residual earthfault
Issued: April 1999 Status: Updated Version: B/09.11.2001 Data subject to change without notice Features Sensitive restricted earth-fault protection stage for fast, selective earth-fault protection Sensitive
More informationMINER-S Station Controller. Substation Automation
Substation Automation MINER-S Station Controller incorporates traditional RTU functions with new technology in a compact design MINER-S Station Controller combines the functions of a traditional RTU with
More informationResidual overvoltage relay
Page 1 Issued: April 1999 Status: New Data subject to change without notice Features Definite-time residual overvoltage earthfault protection and supervision Two independent operation stages, e.g. one
More informationProtection and Control IED Manager PCM600 Product Guide
Protection and Control IED Manager Product Guide Protection and Control IED Manager Product version: 2.9 Contents 1. Description... 3 2. Project explorer... 3 3. Parameter setting... 3 4. Graphical application
More informationPRODUCT GUIDE. COM600F Distribution automation controller
PRODUCT GUIDE COM600F Distribution automation controller 2 COM600F V5.0 DISTRIBUTION AUTOMATION CONTROLLER PRODUCT GUIDE Table of contents 04 05 General description 06 Application 07 08 Process visualization
More informationMINER-S Station Controller
MINER-S Station Controller Substation Automation MINER-S Station Controller The MINER-S Station Controller is a SCADA enabled fixed point remote terminal unit (RTU) with a data concentrator, event reporter,
More informationSynchro-check relay. Application
Issued: April 1999 Status: Updated Version: B/08.11.2001 Data subject to change without notice Features Two identical operation stages allowing the closing conditions of two separate circuit breakers to
More informationDirectional or Non-Directional Earth-Fault Relay REJ 527. Product Guide
Directional or Non-Directional Earth-Fault Product Guide Issued: 17.06.19994 Status: Updated Version: C/16.10.2002 Data subject to change without notice Features Directional or non-directional low-set
More informationFeeder protection relay SPAA 341 C. Product Guide
Issued: April 1999 Status: Updated Version: D/07.03.2006 Data subject to change without notice Features Comprehensive numerical feeder protection relay consisting of two multi-function protection relay
More informationINGEPAC DA-CU. Control Unit. Data Sheet ZY8932IMA01E 31/03/2016
ZY8932IMA01E 31/03/2016 INGEPAC DA-CU Control Unit Data Sheet Total or partial reproduction of this publication by any means or procedure is prohibited without previous express written authorisation by
More informationSubstation automation products. MicroSCADA Pro for substation automation
Substation automation products for substation automation Perfect control anywhere, anytime is an investment for today and tomorrow. Start, for instance, with monitoring or gateway functionality and integrate
More informationScout-S Station Controller
Scout-S Station Controller Substation Automation Scout-S Station Controller The Scout-S Station Controller is a SCADA enabled remote terminal unit (RTU) with a data concentrator, event reporter, and built-in
More informationTM241CE24T controller M IO transistor PNP Ethernet
Characteristics controller M241 24 IO transistor PNP Ethernet Main Range of product Product or component type [Us] rated supply voltage Apr 10, 2018 Modicon M241 Logic controller 24 V DC Discrete input
More informationTM241CE40T controller M IO transistor PNP Ethernet
Characteristics controller M241 40 IO transistor PNP Ethernet Main Range of product Product or component type [Us] rated supply voltage 18 Nov, 2018 Modicon M241 Logic controller 24 V DC Discrete input
More informationFeeder protection relay
Page 1 Issued: April 1999 Status: New Data subject to change without notice Features Comprehensive numerical feeder protection relay consisting of two multi-function protection relay modules and a flexible
More informationTM241CE24U controller M IO transistor NPN Ethernet
Characteristics controller M241 24 IO transistor NPN Ethernet Main Range of product Product or component type [Us] rated supply voltage Mar 09, 2017 Modicon M241 Logic controller 24 V DC Discrete input
More informationTM251MESC controller M251 Ethernet CAN
Characteristics controller M251 Ethernet CAN Price* : 278.88 GBP Main Range of product Product or component type [Us] rated supply voltage Complementary Number of I/O expansion module Supply voltage limits
More informationFeeder Protection Relay REF 610. Product Guide
Product Guide Contents 1 Description.............................. 3 2 Protection functions....................... 3 3 Measurement............................ 4 4 Disturbance recorder......................
More informationCombined Overcurrent and Earth-fault Relay SPAJ 141 C. Product Guide
Combined Overcurrent and Earth-fault Product Guide Issued: April 1999 Status: Updated Version: C/19.04.2006 Data subject to change without notice Features Three-phase, low-set phase overcurrent unit with
More informationTM241CE40R controller M IO relay Ethernet
Characteristics controller M241 40 IO relay Ethernet Main Range of product Product or component type [Us] rated supply voltage Apr 10, 2018 Modicon M241 Logic controller 100...240 V AC Discrete input number
More informationRelion 605 series. Self-powered feeder protection REJ603 Product Guide
Relion 605 series Relion 605 series Relion 605 series Self-powered feeder protection Product Guide Product version: 3.0 Contents 1. Description... 3 2. Relay functions... 3 3. Protection functions... 4
More informationTU531, TU532 Terminal Unit
Ordering Data DATA SHEET TU531, TU532 Terminal Unit 1 Ordering Data Part No. Description Product Life Cycle Phase *) 1SAP 217 200 R0001 1SAP 217 000 R0001 1SAP 417 000 R0001 TU531, terminal unit, 230 VAC,
More informationPart No. Description Product Life Cycle Phase *) unit, 24 VDC, spring terminals. unit, 24 VDC, spring terminals, XC version
Ordering Data DATA SHEET TU520 Terminal Unit 1 Ordering Data Part No. Description Product Life Cycle Phase *) 1SAP 214 400 R0001 1SAP 414 400 R0001 TU520-ETH, PROFINET I/O terminal unit, 24 VDC, spring
More informationTM241CE40R controller M IO relay Ethernet
Characteristics controller M241 40 IO relay Ethernet Main Range of product Product or component type [Us] rated supply voltage Mar 09, 2017 Modicon M241 Logic controller 100...240 V AC Discrete input number
More informationCOM600S - substation automation, analysis and data management Product Guide
- substation automation, analysis and data management Product Guide Copyright This document and parts thereof must not be reproduced or copied without written permission from, and the contents thereof
More informationTM241CE24T controller M IO transistor PNP Ethernet
Product data sheet Characteristics TM241CE24T controller M241 24 IO transistor PNP Ethernet Complementary Main Discrete I/O number 24 Number of I/O expansion module Supply voltage limits Inrush current
More informationTM3DI16 module TM3-16 inputs
Characteristics module TM3-16 inputs Main Range of product Product or component type Range compatibility Jun 30, 2018 Modicon TM3 Discrete input module Modicon M241 Modicon M251 Modicon M221 Discrete input
More informationTM241CE24T controller M IO transistor PNP Ethernet
Characteristics controller M241 24 IO transistor PNP Ethernet Product availability : Stock - Normally stocked in distribution facility Price* : 479.00 USD Main Range of product Product or component type
More informationHigh impedance protection relay
High impedance protection relay Page 1 Issued: April 1999 Status: New Data subject to change without notice Features High impedance type differential current earth-fault protection, so called restricted
More informationTM3AI4 module TM3-4 analog inputs
Characteristics module TM3-4 analog inputs Main Range of product Product or component type Range compatibility Analogue input number 4 Analogue input type Complementary Analogue input resolution Permissible
More informationTM241CEC24R controller M IO relay Ethernet CAN master
Characteristics controller M241 24 IO relay Ethernet CAN master Main Range of product Product or component type [Us] rated supply voltage Nov 28, 2017 Modicon M241 Logic controller 100...240 V AC Discrete
More informationCM597 Ethernet Communication Module
Ordering Data DATA SHEET CM597 Ethernet Communication Module 1 Ordering Data Part No. Description Product Life Cycle Phase *) 1SAP 173 700 R0001 1SAP 373 700 R0001 CM597-ETH, communication module Ethernet
More informationTM241C40U controller M IO transistor NPN
Characteristics controller M241 40 IO transistor NPN Main Range of product Product or component type [Us] rated supply voltage 15/12/2018 Modicon M241 Logic controller 24 V DC Discrete input number 24
More informationTM221CE40R controller M IO relay Ethernet
Characteristics controller M221 40 IO relay Ethernet Main Range of product Product or component type [Us] rated supply voltage Jan 6, 2019 Modicon M221 Logic controller 100...240 V AC Discrete input number
More informationTransformer Protection Relay
Transformer Protection Relay T-PRO Product Overview The IEC 61850 station bus embedded T-PRO relay provides complete three-phase multi-winding transformer protection and overload protection, DFR-quality
More informationTM221CE40T controller M IO transistor PNP Ethernet
Product data sheet Characteristics TM221CE40T controller M221 40 IO transistor PNP Ethernet Complementary Main Discrete I/O number 40 Number of I/O expansion module Supply voltage limits Inrush current
More informationTM221ME32TK controller M IO transistor PNP Ethernet
Product data sheet Characteristics TM221ME32TK controller M221 32 IO transistor PNP Ethernet Complementary Main Discrete I/O number 32 Number of I/O expansion module Supply voltage limits Inrush current
More informationTM241C24T controller M IO transistor PNP
Characteristics controller M241 24 IO transistor PNP Main Range of product Product or component type [Us] rated supply voltage Feb 13, 2018 Modicon M241 Logic controller 24 V DC Discrete input number 14
More informationTM241CE40R controller M IO relay Ethernet
Characteristics controller M241 40 IO relay Ethernet Product availability : Stock - Normally stocked in distribution facility Price* : 559.00 USD Main Range of product Product or component type [Us] rated
More informationTM241CE40R controller M IO relay Ethernet
Product data sheet Characteristics TM241CE40R controller M241 40 IO relay Ethernet Complementary Main Discrete I/O number 40 Discrete input logic Discrete input voltage Discrete input voltage type Voltage
More informationTM200CE24T controller M IO transistor Source+ Ethernet
Product datasheet Characteristics TM200CE24T controller M200 24 IO transistor Source+ Ethernet Main Range of product Product or component type [Us] rated supply voltage Discrete I/O number 24 Discrete
More informationTM3TI8T module TM3-8 inputs temperature
Characteristics module TM3-8 inputs temperature Main Range of product Product or component type Range compatibility Analogue input number 8 Analogue input type Complementary Analogue input resolution Input
More informationTM258LD42DT4L compact base M I/O - 24 V DC
Characteristics compact base M258-42 + 4 I/O - 24 V DC Main Range of product Product or component type Product specific application - Discrete I/O number 42 Analogue input number 4 Discrete output number
More informationTM221M16R controller M IO relay
Product data sheet Characteristics TM221M16R controller M221 16 IO relay Complementary Main Discrete I/O number 16 Number of I/O expansion module Supply voltage limits Inrush current Power consumption
More informationTM251MESE. Main. [Us] rated supply voltage. 14 with remote I/O architecture W with max number of I/O expansion module
Product datasheet Characteristics TM251MESE Main Range of product Product or component type [Us] rated supply voltage Modicon M251 Logic controller 24 V DC Complementary Number of I/O expansion module
More informationTM5C12D6T6L compact I/O expansion block TM5-24 I/0-12 DI - 6 DO transistor - 4 AI - 2 AO
Characteristics compact I/O expansion block TM5-24 I/0-12 DI - 6 DO transistor - 4 AI - 2 AO Main Range of product Product or component type Complementary Enclosure material Colour Input/Output number
More informationType MVTT 14 and MVTT 15: Static Digital Time delay relays
Type MVTT 4 and MVTT 5: Static Digital Time delay relays Features 000/ setting range Time settings easily selected by means of thumbwheel switches Provide time delayed pick-up, or drop-off Compact construction
More informationTM221CE24R controller M IO relay Ethernet
Product data sheet Characteristics TM221CE24R controller M221 24 IO relay Ethernet Complementary Main Discrete I/O number 24 Number of I/O expansion module Supply voltage limits Network frequency Inrush
More informationekorrps MULTIFUNCTIONAL PROTECTION UNIT CONFIGURATION AND GENERAL CHARACTERISTICS LIB
MO-067-EN Operation Manual MULTIFUNCTIONAL PROTECTION UNIT CONFIGURATION AND GENERAL CHARACTERISTICS LIB Transformer Substations Secondary Distribution Switchgear Primary Distribution Switchgear Protection
More informationTM221CE24T controller M IO transistor PNP Ethernet
Characteristics controller M221 24 IO transistor PNP Ethernet Main Range of product Product or component type [Us] rated supply voltage Discrete input number Analogue input number Discrete output type
More informationTM221ME16T controller M IO transistor PNP Ethernet
Characteristics controller M221 16 IO transistor PNP Ethernet Main Range of product Product or component type [Us] rated supply voltage Discrete input number Analogue input number Discrete output type
More informationTF501, TF521 Terminal Bases
Ordering Data DATA SHEET TF501, TF521 Terminal Bases 1 Ordering Data Part No. Scope of delivery Product life cycle status 1SAP 117 000 R0271 1SAP 317 000 R0271 1SAP 117 200 R0271 1SAP 317 200 R0271 TF501-CMS,
More informationTM258LF42DT compact base M I/O - 24 V DC - CANopen
Characteristics compact base M258-42 I/O - 24 V DC - CANopen Main Range of product Product or component type Product specific application - Discrete I/O number 42 Discrete output number Complementary Discrete
More informationRE17LAMW on-delay timing relay - 1 s..100 h V AC/ DC - solid state output
Characteristics on-delay timing relay - 1 s..100 h - 24..240 V AC/ DC - solid state output Main Range of product Product or component type Discrete output type Width Component name Time delay type Time
More informationPublished by and copyright 2015 Siemens AG Energy Management Freyeslebenstr Erlangen, Germany
Published by and copyright 2015 Siemens AG Energy Management Freyeslebenstr. 1 91058 Erlangen, Germany For more information, please contact our Customer Support Center Phone: +49 180/524 84 37 Fax: +49
More informationTM221M32TK controller M IO transistor PNP
Characteristics controller M221 32 IO transistor PNP Main Range of product Product or component type [Us] rated supply voltage Discrete input number Analogue input number Discrete output type Discrete
More informationTM3TI4 module TM3-4 inputs temperature
Characteristics module TM3-4 inputs temperature Main Range of product Product or component type Range compatibility Analogue input number 4 Analogue input type Complementary Analogue input resolution Permissible
More informationZBRN1 access point- 2 RJ V AC/DC-4 displays-5 LEDs-Eth-Modbus-wireless radio
Characteristics access point- 2 RJ45-24..240V AC/DC-4 displays-5 LEDs-Eth-Modbus-wireless radio Main Range of product Product or component type Device short name Product specific application Function of
More informationRE22R1QMQ star-delta timing relay - 230VAC/440VAC - 1 C/O
Characteristics star-delta timing relay - 230VAC/440VAC - 1 C/O Main Range of product Product or component type Discrete output type Device short name Nominal output current Complementary Contacts type
More informationHigh Impedance Protection Relay SPAE010, SPAE011. Product Guide
SPAE010, SPAE011 SPAE010, SPAE011 1MRS750383-MBG Issued: April 1999 Status: Updated Version: D/21.03.2006 Data subject to change without notice Features High impedance type differential current earth-fault
More informationTM3TM3 module TM3-2 temperature inputs and 1 analog output
Characteristics module TM3-2 temperature inputs and 1 analog output Main Range of product Product or component type Range compatibility Analogue input number 2 Analogue input type Analogue output number
More informationTM241C40R controller M IO relay
Characteristics controller M241 40 IO relay Main Range of product Product or component type [Us] rated supply voltage Mar 09, 2017 Modicon M241 Logic controller 100...240 V AC Discrete input number 24
More informationFL MC 2000E (SM40) LC
IEC 61850 fiber optic converter with LC fiber optic connection (1310 nm) to convert 100Base-Tx to single- or multi-mode fiber glass Data sheet 3205_en_C 1 Description PHOENIX CONTACT 2014-04-04 2 Features
More informationTM3SAC5RG SAFETY MODULE FOR PLC TM2xx, 1 FUNCTION, CAT3, SPRING TERMINALS
Characteristics SAFETY MODULE FOR PLC TM2xx, 1 FUNCTION, CAT3, SPRING TERMINALS Main Range of product Product or component type Device short name Safety module application Function of module Jun 29, 2018
More informationTM251MESC controller M251 Ethernet CAN
Characteristics controller M251 Ethernet CAN Product availability : Stock - Normally stocked in distribution facility Price* : 519.00 USD Main Range of product Product or component type [Us] rated supply
More informationTM221M16TG controller M IO transistor PNP spring
Characteristics controller M221 16 IO transistor PNP spring Main Range of product Product or component type [Us] rated supply voltage Discrete input number Analogue input number Discrete output type Discrete
More informationTM258LD42DT4L compact base M I/O - 24 V DC
Characteristics compact base M258-42 + 4 I/O - 24 V DC Main Range of product Product or component type Product specific application Discrete I/O number 42 Analogue input number 4 Discrete output number
More informationAO523 Analog Input Module
Ordering Data DATA SHEET AO523 Analog Input Module 1 Ordering Data Part No. Description Product Life Cycle Phase *) 1SAP 250 200 R0001 1SAP 450 200 R0001 AO523, analog output module, 16 AO, U/I, 12 bits
More informationCM589 PROFINET Communication Module
Ordering Data DATA SHEET CM589 PROFINET Communication Module 1 Ordering Data Part No. Description Product Life Cycle Phase *) 1SAP 172 900 R0011 1SAP 372 900 R0011 1SAP 172 900 R0111 1SAP 372 900 R0111
More informationCM579-PNIO PROFINET Communication Module
Ordering Data DATA SHEET CM579-PNIO PROFINET Communication Module 1 Ordering Data Part No. Description Product Life Cycle Phase *) 1SAP 170 901 R0101 1SAP 370 901 R0101 CM579-PNIO, PROFINET communication
More informationElectrical Integration with Smart Communication
Electrical Integration with Smart Communication New possibilities with Industrial Ethernet ABB Group September 24, 2009 Slide 1 Unified Integration Approach MES and Business Systems Knowledge Portals as
More informationOTB1E0DM9LP I/O distributed module OTB - Ethernet TCP/IP m
Characteristics I/O distributed module OTB - Ethernet TCP/IP - 0..100 m Main Range of product Product or component type Integrated connection type Mar 31, 2018 Modicon OTB I/O distributed module Discrete
More informationGrid Automation Products. MicroSCADA Pro Substation automation applications.
Grid Automation Products Substation automation applications. 2 Substation automation applications Automate, control and optimize your operations. is an investment for today and tomorrow. Start, for instance,
More informationXPSMF35. Product data sheet Characteristics. Preventa safety PLC compact - Profibus DP protocol. Main. Complementary. Safety module name
Product data sheet Characteristics XPSMF3542 Preventa safety PLC compact - Profibus DP protocol Main Range of product Product or component type Safety module name Safety module application Nov 13, 2018
More informationMicroSCADA Pro Substation automation applications.
G R I D AUTO M ATI O N PRO D U C T S Substation automation applications. ABB Oy Finland Power Grids Grid Automation P.O. Box 614 FI-65101 Vaasa, Finland Phone: +358 10 22 21999 (Customer Support Center)
More informationAnalog output 520AOD01 Data sheet
RTU520 product line Analog output 520AOD01 Data sheet ERR RTU I/O bus Microcontroller RAM Flash Output register DC DC D D A A Adjustment Output range O1 O2 Adjustment Output range IOC UE Figure 1: Block
More informationINTRODUCTION. The PL-50 MO and PM-250 families represent the. PM-250-H: Horizontal box. PM-250-V: Vertical box
INTRODUCTION The PL-50 MO units are available in the next mechanical version: The PL-50 MO and PM-250 families represent the different solutions that Team Arteche offers for motor protection. Both families
More informationCPU6501 REV1.0 1 WILLOWGLEN MSC BERHAD
CPU6501 REV1.0 1 RESPONSIBLE PERSON REVISION RELEASE DATE COMPOSER JOB TITLE APPROVALS JOB TITILE 0.0 10 th MAR 2016 SIDEK MANAGER NIK AZLAN CTO 1.0 26/10/2016 Farm Zheng Lin HW Engineer Mohd Sidek HW
More informationATV930U30M3 variable speed drive - ATV930-3kW - 200/240Vwith braking unit - IP21
Characteristics variable speed drive - ATV930-3kW - 200/240Vwith braking unit - IP21 Main Range of product Product or component type Device application Device short name Variant Product destination Mounting
More informationLMC058LF42 compact base - 42 I/O - 24 V DC supply
Characteristics compact base - 42 I/O - 24 V DC supply Product availability : Stock - Normally stocked in distribution facility Price* : 2054.54 USD Main Range of product Product or component type Product
More informationTM241CEC24T. Main. 14 (remote I/O architecture) W with max number of I/O expansion module ma fast input. 2.
Product datasheet Characteristics TM241CEC24T Main Range of product Product or component type [Us] rated supply voltage Discrete input number Discrete output type Discrete output number Discrete output
More informationRE17LCBM off-delay timing relay - control - 1 s..100 h V - solid state output
Characteristics off-delay timing relay - control - 1 s..100 h - 24..240 V - solid state output Main Range of product Product or component type Discrete output type Width Component name Time delay type
More information