Important Safety Instructions

Size: px

Start display at page:

Download "Important Safety Instructions"

Ginger Gabriella Patrick
5 years ago
Views:

1 Instruction Manual CD Cassette Boombox

2 Important Safety Instructions TO PREVENT FIRE OR SHOCK HAZARD, DO NOT USE THIS PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADE SCAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK), NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. 1. READ INSTRUCTIONS - All the safety and operating instructions should be read before the product is operated. 2. RETAIN INSTRUCTIONS - The safety and operating instructions should be retained for future references. 3. HEED WARNINGS - All warnings on the product and in the operating instructions should be adhered to. 4. FOLLOW INSTRUCTIONS - All operating and user instructions should be followed. 5. WATER AND MOISTURE - Do not use this product near water (a bathtub, washbowl, kitchen sink, laundry tub, wet basement, or swimming pool for example). 6. VENTILATION - Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug or other similar surface. This product should not be placed in a built-in installation, such as a bookcase or rack, unless proper ventilation is provided or the manufacturer*instructions have been adhered to. 7. HEAT - The product should be situated away from heat source such as radiators, heat registers, stoves or other products (including amplifiers) that produce heat. 8. POWER SOURCES - This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your appliance dealer or or local power company. For products intended for operation from battery power, or other sources, refer to the operating instructions. 9. POWER CORD PROTECTION - Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them. Pay particular attention to cords at plugs, convenience receptacles, and the POINT WHERE THEY EXIT FROM THE PRODUCT. 10. POWER LINES - An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. 11. OBJECT AND LIQUID ENTRY - Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product. 12. ESD WARNING - If the display or the controls do not function properly it may be due to an electrostatic discharge. Switch off and unplug the product. Reconnect after a few seconds. 13. DAMAGES REQUIRING SERVICE - Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions : (a). When the power-supply cord or plug is damaged. (b). If liquid has been spilled, or objects have fallen onto the product. (c). If the product has been exposed to rain or water. (d). If the product does not operate normally after following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation. (e). When the product exhibits a distinct change performance - this indicates a need for service. 14. SERVICING - Servicing is required when the product has been damaged in any way, such as the power-supply cord or plug being damaged, liquid spillage, or objects falling on or into the product - anything that causes the apparatus to not operate normally. Refer all servicing to qualified service personnel. 15. GROUNDING OR POLARIZATION - This product may be equipped with a polarized alternating current line plug (a plug having one blade wider then the other). This plug will fit the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. DO NOT defeat the safety purpose of the polarized plug. 1

3 Warnings 1. WARNING: Please refer to the label on the exterior bottom of this apparatus for all electrical and safety information before installing or operating this apparatus. 2. WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. The apparatus shall not be exposed to dripping or splashing and that objects filled with liquids, such as vases, shall not be placed on apparatus. 3. WARNING: The batteries shall not be exposed to excessive heat such as sunshine, fire or the like. 4. WARNING: The wall socket plug is used as disconnect device, the disconnect device shall remain readily operable. 5. WARNING: Excessive sound levels from earphones or headphones can cause hearing loss. Battery Warnings Batteries must be inserted taking care to match the polarities shown. Make sure that the (+) and (-) terminals are placed in the right direction. Never use batteries that show signs of electrolyte leaks or cracking. Never dispose of used batteries in an open fire. Keep batteries out of reach of children. Never recharge disposable batteries. Never short circuit battery terminals. Always remove used batteries from the appliance case. Do not try to open the batteries. Do not mix up different kind of batteries or new and already used batteries together. Only use batteries of the recommended or equivalent type. Remove batteries from the appliance before disposing of it at the end of its service life. CAUTION! HAZARDOUS LASER RADIATION WHEN OPEN AND INTERLOCK FAILED OR DEFEATED. AVOID EXPOSURE TO BEAM CLASS 1 LASER PRODUCT 2

4 The FCC Wants You To Know This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed or used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1) reorient or relocate the receiving antenna; 2) increase the separation between the equipment and the receiver; 3) connect the equipment to an outlet on a circuit different from that to which the receiver is connected; 4) consult the dealer or an experienced radio/tv technician for additional suggestions. Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment. Where shielded interface cables have been provided with the product or specified additional components or accessories elsewhere defined to be used with the installation of the product, they must be used in order to ensure compliance with FCC regulation. CAN ICES-3(B). 3

5 Power Sources INSERT 6 X C SIZE BATTERIES INTO THE BATTERY COMPARTMENT TO AC IN TO WALL OUTLET Using AC Power 1. You can power your portable system by plugging the detachable AC power cord into the AC outlet at the back of the product and into a wall outlet. 2. Check that the rated voltage of the product matches your local voltage. 3. Make sure that the AC power cord is fully inserted into the product. Using Battery Power 1. Insert 6 x C size batteries into the battery compartment. Be sure that the batteries are inserted correctly (matching the polarity markings shown) to avoid damage to the product. 2. Always remove the batteries when the product will not be used for a long period of time, as the batteries may leak causing damage to the product. WARNING: Incorrect use of batteries can cause electrolyte leakage and will corrode the compartment or cause the batteries to burst. Therefore: Use batteries of the same type. Never use different types of batteries together. When using batteries with the product, disconnect the AC power cord from it. When inserting new batteries, do not try to mix old batteries with new ones. Batteries contain chemical substances, so they should be disposed of properly. 4

6 Location of Controls HEADPHONE JACK FM ANTENNA FUNCTION SELECTOR VOLUME CONTROL TUNING CONTROL CD DOOR BAND SELECTOR OPEN/CLOSE DIAL POINTER TAPE BUTTONS - PAUSE, STOP/EJECT, FAST FORWARD, REWIND, PLAY, RECORD POWER INDICATOR LED DISPLAY FM STEREO INDICATOR SKIP + SKIP - REPEAT PLAY/PAUSE STOP PROGRAM CASSETTE DOOR 5

7 Radio Operation General Operation 1. Set the FUNCTION selector to RADIO mode. 2. Select the desired band width using the BAND selector. 3. Adjust the radio frequency to your desired station by using the TUNING control. 4. Adjust the VOLUME control to the desired level. AM/FM/FM-Stereo Reception 1. Set the BAND selector to FM mode for MONO reception. 2. Set the BAND selector to FM ST. mode for FM Stereo reception. The stereo indicator LED lights up showing you are in FM ST. mode. For Better Reception For FM reception reorient the antenna by, pulling out the telescopic antenna, then incline and turn the antenna. Reduce its length if the spiral is too long (very close to transmitter). For AM reception reorient the antenna by turning the whole product. The product is provided with a built-in antenna so the telescopic antenna is not needed. 6

8 Tape Operation General Operation PAUSE Press to temporarily stop the tape playing. Press again to resume operation. STOP/EJECT Press to stop the tape playing. Press again to open the cassette door after the tape spools stop turning. FAST FORWARD & REWIND Press to start rapid tape winding; either forward or in the reverse direction. PLAY Press to start playing the tape. RECORD Press the RECORD and PLAY buttons together to start recording. Playback 1. Set the FUNCTION selector to TAPE mode. 2. Press the STOP/EJECT button to open the cassette door and insert your tape. 3. Close the cassette door. 4. Press the PLAY button to play the tape. 5. Adjust the VOLUME control to the desired level. 6. Press the PAUSE button when you want to stop playing the tape temporarily. 7. Press the STOP/EJECT button when finished. Recording 1. Press the STOP/EJECT button to open the cassette door and insert a blank tape. 2. Select the source you want to record. To record from the radio: Set the FUNCTION selector to RADIO mode and adjust to the desired station. To record from CD: Place a disc in the CD compartment. Set the FUNCTION selector to CD mode and select the desired track. 3. Press the RECORD and PLAY buttons together to start recording. 4. Press the STOP/EJECT button when finished. Maintenance Tape Deck Maintenance To ensure quality recording and playback of the tape deck, clean parts A, B and C shown in the diagram (after approximately 50 hours of operation, or an average of once a month). Use a cotton bud slightly moistened with alcohol or a special head cleaning fluid to clean the deck. 1. Open the cassette door by pressing STOP EJECT. 2. Press PLAY and clean the rubber pressure rollers C. 3. Press PAUSE and clean the magnetic heads A and also the Capstan B. 4. After cleaning press STOP EJECT. Note: Cleaning the heads can also be done by playing a cleaning cassette through once. 7

9 CD Operation General Operation PLAY/PAUSE Press to start playing the CD disc. Press again to temporarily stop playing the CD. Press again to resume playback. SKIP + and Press to go to the next track or back to the previous track. SKIP - Press and hold while playing until you find the point of sound. STOP Press to stop all CD operation. Playback 1. Set the FUNCTION selector to CD mode. 2. Open the CD door and place a CD disc with the label side up into the CD compartment. 3. Close the CD door. 4. A focus search is performed on the inserted CD disc. The total number of tracks is read and appears on the display. 5. Press the PLAY/PAUSE button to start playing the CD disc. 6. Adjust the VOLUME control to the desired level. 7. Press the PLAY/PAUSE button again when you want to stop playback temporarily. 8. Press the STOP button when finished. Program Up to 20 tracks can be programmed for disc play in any order. Be sure to press the STOP button before use. 1. Press the PROGRAM button, the display will show 01 and flash. 2. press the desired track by using the SKIP + or SKIP - button. 3. Press the PROGRAM button again to confirm the desired track into the program memory. 4. Repeat steps 2 and 3 to enter additional tracks into the program memory. 5. When all the desired tracks have been programmed, press the PLAY/PAUSE button to begin playing the disc in the order you have programmed it. The program indicator light will start flashing. 6. Press the STOP button twice to terminate the programmed play. The program indicator light stops flashing. Repeat Press the REPEAT button before or during CD play. A single track or all tracks can be repeated. Each press switches the repeat mode as follows; 1- REPEAT 1 (The repeat indicator is flashing.) 2- REPEAT ALL (The repeat indicator is constantly on.) 3- NORMAL PLAYBACK. 8

10 Other Operation Headphone Jack Connects to a 3.5 mm headphones (not included). Use the volume control to adjust the sound level of the headphones. Maintenance & Safety Precautions & General Maintenance Place the unit on a hard flat surface so the system does not tilt. Do not expose the unit, batteries or CDs to humidity, rain, sand or excessive heat caused by heating equipment or direct sunlight. Do not cover the unit. Adequate ventilation with a minimum gap of 15cm (6 inches) between the ventilation holes and surrounding surfaces is necessary to prevent heat build-up. The mechanical parts of the set contain self-lubricating bearings and must not be oiled or lubricated. To clean the unit, use a soft dry cloth. Do not use any cleaning agents containing alcohol, ammonia, benzene or abrasives as these may harm the housing. CD Player and CD Handling The lens of the CD player should never be touched! Sudden changes in the surrounding temperature can cause condensation to form and the lens of your CD player to cloud over. Playing a CD would not become possible. Do not attempt to clean the lens. Instead, leave the unit in a warm environment until the moisture evaporates. Always close the CD door to keep the CD compartment dust-free. To clean, dust the compartment with a soft dry cloth. To clean the CD, wipe in a straight line from the centre towards the edge using a soft, lint-free cloth. Do not use cleaning agents as they may damage the disc. Never write on a CD or attach any stickers to it. 9

11 Troubleshooting If a fault occurs, first check the points listed below before taking the unit for repair. Do not open the unit as there is a risk of electric shock. If you are unable to remedy a problem by following these hints, consult your dealer or service centre. WARNING: Under no circumstances should you try to repair the unit yourself, as this will void the warranty. PROBLEM 10 SOLUTION NO SOUND OR POWER Volume not adjusted Adjust the volume DISPLAY DOES NOT FUNCTION PROPERLY/ NO REACTION TO OPERATION OF ANY OF THE CONTROLS POOR CASSETTE SOUND QUALITY RECORDING DOES NOT WORK Power cord not securely connected Batteries dead or incorrectly inserted Electrostatic discharge Dust and dirt on the heads, etc. Use of incompatible cassette types (METAL or CHROME) Cassette tab(s) may be broken Connect the AC power cord correctly Insert (fresh) batteries correctly Switch off and unplug the unit. Reconnect after a few seconds Clean deck parts etc., (see Maintenance) Only use NORMAL (IEC I) for recording Apply a piece of adhesive tape over the missing tab space NO DISC INDICATION No CD inserted Insert a CD, CD-R or CD-RW CD PLAYBACK DOES NOT WORK CD badly scratched or dirty Laser lens steamed up CD-R is blank or the disc is not finalized CD badly scratched/dirty Laser lens steamed up Replace/clean CD, (see Maintenance) Wait until lens has adjusted to room temperature Use a finalized CD-R Replace/clean CD (see Maintenance) Wait until lens has adjusted to room temperature THE CD SKIPS TRACKS CD damaged or dirty Replace or clean CD Environmental Information Program mode is active Quit program mode(s) We have done our best to reduce the packaging and make it easy to separate into 3 materials; cardboard, polyethylene and expandable polystyrene. Your equipment consists of materials that can be recycled if disassembled by a specialized company. Please observe the local regulations regarding the disposal of packaging, dead batteries and old equipment.

12 Specifications Programmable top loading CD, CD-R/RW Recordable cassette player Analog tuning with AM/FM/FM-Stereo 3.5 mm headphone jack Frequency: AM KHz and FM MHz Power: Option 1) AC 120, 60Hz Option 2) 6 x C batteries (not included). We recommend InfiniCell batteries for maximum performance. Distortion: 10 % THE SOURCE WARRANTY Imported by: The Source, Barrie, Ontario, Canada, L4M 4W5 Manufactured in China For product support please visit The Source All rights reserved. Please Recycle 11

AZ1008. CD Radio Cassette Recorder DBB REPEAT CD TRACK PROGRAM

AZ1008. CD Radio Cassette Recorder DBB REPEAT CD TRACK PROGRAM AZ 1008 Radio Cassette Recorder RADIO CASSETTE RECORDER BASS REFLEX SPEAKER SYSTEM 1 2 3 4 1 5 RADIO CASSETTE RECORDER BASS REFLEX SPEAKER SYSTEM 6 7 8 9 0! @ # $ % AC MAINS ~ ^ 3 Controls Power Supply