Blu<>Hub Dongle07. Installation and Operation Instructions #JBLU-BHDG07-EB03. With JMAHP Software Profile

Transcription

1 Blu<>Hub Dongle07 With JMAHP Software Profile #JBLU-BHDG07-EB J&M Corporation. All rights reserved. 7/11 Installation and Operation Instructions

2 Table of Contents Product Description Section 1 Safety & General Information Section 2 Package Contents Section 3 Installation Instructions Section 4 General Operation Instructions Section 5 Linking/Pairing Scenarios Section 6 1. Product Description This is a J&M custom Blu<>Hub dongle07 module featuring our exclusive JMAHP (J&M Motorcycle Audio Headset Profile) Bluetooth software profile, transmitting true stereo to 1 or 2 J&M Bluetooth headsets, with simultaneous microphone signals transmitted back down to the dongle. When 2 J&M Bluetooth headsets are linked to the dongle07, the continuous helmet-to-helmet intercom feature is activated thru the dongle. Rider and passenger can also each simultaneously link their J&M Bluetooth helmet headsets to their own cell phone or Garmin Zumo, while linked to the Blu<>Hub dongle07. This dongle07 is used to create a full featured motorcycle audio system, with stereo music, CB/FRS, Navigation commands, cell phone etc. available depending upon the capabilities of the external equipment being connected. The J&M dongle07 is powered by the electrical system on the motorcycle (no batteries in the dongle to charge). 2. Safety and General Information IMPORTANT INFORMATION FOR SAFE AND EFFICIENT OPERATION. READ THIS INFORMATION BEFORE USING YOUR DEVICE. Users are not permitted to make changes or modify the device in any way. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. See 47 CFR Sec This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. See FCC 47 CFR Sec (3). ELECTROMAGNETIC INTERFERENCE/COMPATIBILITY: Note: Nearly every electronic device is susceptible to electro-magnetic interference (EMI) if inadequately shielded, designed or otherwise configured for electromagnetic compatibility. FACILITIES: To avoid electromagnetic interference and/or compatibility conflicts, turn off your device in any facility where posted notices instruct you to do so. Hospitals or health care facilities may be using equipment that is sensitive to external RF energy. AIRCRAFT: When instructed to do so, turn off your device when on board an aircraft. Any use of a device must be in accordance with applicable regulations per airline crew instructions. MEDICAL DEVICES HEARING AIDS: Some devices may interfere with some hearing aids. In the event of such interference, you may want to consult with your hearing aid manufacturer to discuss alternatives. OTHER MEDICAL DEVICES If you use any other personal medical device, consult the manufacturer of the device to determine if it is adequately shielded from RF energy. Your physician may be able to assist you in obtaining this information. Industry Canada Notice to Users: Operation is subject to the following two conditions: (1) This device may not cause interference and (2) This device must accept any interference, including interference that may cause undesired operation of the device. FCC Notice to Users: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/tv technician for help. 3. Package Contents JBLU-BHDG07-EB03

3 Diagram A speaker on/off switch to BMW radio to BMW radio iphone/droid/ Blackberry (not included) to rear-mounted CB antenna (not included) 6-pin plugs 9-pin plugs 6-pin plug driver s antenna driver's helmet headset (not included) link/pairing buttons 6-pin din 6-pin plugs 2-pin plug Extra switched power connection point for J&M BLU<>HUB dongle. 3-pin plug inline noise filter passenger CB transmit switch red fuse holder 2-pin plug ground to frame battery post + Radar Detector passenger s antenna orange 12 volt switchable source J&M Plug-and-Play Radar Detector Connection Harness (Not Included) 4. Installation Instructions 1. Remove the seat, tour pack if installed, both saddle bags, and rear luggage rack on the K1600GTL, the R1200RT will not need the luggage rack removed. 2. Clean the surface where the BLU<>HUB dongle07 Will be mounted with denatured alcohol. Diagram B. 3. Remove the backing from the double-sided mounting tape and mount the BLU<>HUB dongle07 Diagram B. 4. Plug in the connectors per Diagram A. 5. Clean the surfaces where the antennas will be mounted with denatured alcohol. 6. Remove the backing from the double-sided tape and mount the antennas. The antennas should be mounted up so that the word ant that is written on the double-backed tape is up. Diagram B. Note: Antenna's can be mounted under the plastic panels of the motorcycle, but should not be mounted under any metal. 7. Clean the area just below the passengers left grab rail with denatured alcohol. 8. Remove the backing from the Velcro and stick the driver/passenger pairing/linking buttons under the passengers grab rail. Diagram B.

4 5. General Operation Instructions 1. Once either J&M Bluetooth headset has been paired to this dongle07, they will not need to be re-paired again, as the dongle07 will automatically turn on/off with the ignition switch on your motorcycle. 2. Use the volume up/down buttons on the J&M Bluetooth headset to individually adjust the volume of the driver/passenger intercom, when two headsets Diagram B driver s antenna to power filter 3. If you later pair your J&M Bluetooth headset, to another device/dongle, separate of the dongle07, then return to pair with the dongle07, you will need to clear and re-pair the headset to the dongle07, as per the pairing/linking instructions in section 6. Supported Bluetooth Profile: JMAHP (J&M Motorcycle Audio Headset Profile) to headset lead 6. Linking/Pairing Scenarios Pairing and Operation of the dongle07 to a Single J&M Bluetooth Helmet Headset. driver's motorcycle mounted pairing button for approximately 13 seconds until the flashing blue LED goes off, then release the button. 2. Now press and hold the driver's pairing button for approximately 30 seconds, at which time the blue LED should be flashing rapidly. link/pairing buttons passenger s antenna 3. Turn on the driver's J&M Bluetooth headset, press and hold the multifunction button for approximately 30 seconds until the headset cycles from rapid blue flashing, to red flashing, and back to rapid blue flashing, at which time the headset is cleared and ready to pair to the dongle The headset and dongle07 are paired once the blue LED's on both the headset and the dongle07 flash slowly. 5. To set the music volume, adjust the music source volume that is feeding the dongle07 to a comfortable listening level. 6. If your particular motorcycle audio system includes an 2003E-BW), reduce system intercom volume to minimum, and/or turn the (corded headset) intercom feature off, when using the dongle07. Pairing and Operation of the dongle07 to Two J&M Bluetooth Helmet Headsets. driver's motorcycle mounted pairing button for approximately 13 seconds until the flashing blue LED goes off, then release the button. 2. Now press and hold the driver's pairing button for approximately 30 seconds, at which time the blue LED should be flashing rapidly. 3. Turn on the driver's J&M Bluetooth headset, press and hold the multifunction button for approximately 30 seconds until the headset cycles from rapid blue flashing, to red flashing, and back to rapid blue flashing, at which time the headset is cleared and ready to pair to the dongle The driver's headset and dongle07 are paired once the blue LED's on both the headset and the dongle07 flash slowly. 5. Press and hold the passenger's motorcycle mounted pairing button for approximately 13 seconds until the flashing blue LED goes off, then release the button. 6. Now press and hold the passenger's pairing button for approximately 30 seconds, at which time the blue LED should be flashing rapidly. 7. Turn on the passenger's J&M Bluetooth headset, press and hold the multifunction button for approximately 30 seconds until the headset cycles from rapid blue flashing, to red flashing, and back to rapid blue flashing, at which time the headset is cleared and ready to pair to the dongle07.

5 8. The passenger's headset and dongle07 are paired once the blue LED's on both the headset and the dongle07 flash slowly. 9. Use the volume up/down buttons on the J&M Bluetooth headsets to individually adjust the volume of the driver/passenger intercom, when two headsets 10. To set the music volume, adjust the music source volume that is feeding the dongle07 to a comfortable listening level. 11. If your particular motorcycle audio system includes an 2003E-BW), reduce system (corded headset) intercom volume to minimum or 0. Pairing and Operation of the dongle07 to a J&M Bluetooth Helmet Headset, simultaneously with a cell phone. corresponding motorcycle mounted pairing button for approximately 13 seconds until the flashing blue LED goes off, then release the button. 2. Now press and hold the pairing button for approximately 30 seconds, at which time the blue LED should be flashing rapidly. 3. Turn on the corresponding J&M Bluetooth headset, press and hold the multifunction button for approximately 30 seconds until the headset cycles from rapid blue flashing, to red flashing, and back to rapid blue flashing, at which time the headset is cleared and ready to pair to the dongle The headset and dongle07 are paired once the blue LED's on both the headset and the dongle07 flash slowly. 5. Turn the motorcycle ignition off. 6. Turn the headset off and then back on, press and hold the multifunction button for approximately13 seconds, until the blue LED flashes rapidly. 7. Select the hands-free menu on the cell phone, go into the Bluetooth section and have the cell phone search for devices. When JM_CORP_HHS is displayed on your screen, click on it. When you are asked for a passkey, enter: Your cell phone should now pair with the J&M Bluetooth headset. 8. Turn the motorcycle ignition switch back on and the dongle07 will automatically reconnect to the Headset. 9. At this point both the dongle07 and the cell phone should now be simultaneously linked to the headset. 10. Use the volume up/down buttons on the J&M Bluetooth headset to individually adjust the volume of the driver/passenger intercom, when two headsets 11. To set the music volume, adjust the music source volume that is feeding the dongle07 to a comfortable listening level. 12. If your particular motorcycle audio system includes an 2003E-BW), reduce system (corded headset) intercom volume to minimum or To set the cell phone volume, adjust the volume up or down buttons on the headset during an actual cell phone conversation. Additional cell phone volume adjustments can also be made on the cell phone itself, but during actual conversation only. 14. When placing or receiving a cell phone call, your headset will unlink from the dongle07 for the duration of the call, and then automatically re-pair with the dongle07 when the cell phone call is terminated. (maximum call duration of 59 minutes for this feature) Note: Because of Bluetooth bandwidth limitations, when your cell phone and dongle07 are both simultaneously linked to your J&M Bluetooth headset, you may experience occasional cutting out or loss of data to the headset, which will not affect overall operation. Pairing and Operation of the dongle07 to a J&M Bluetooth Helmet Headset, simultaneously with a Bluetooth Enabled GPS Command Center. corresponding motorcycle mounted pairing button for approximately 13 seconds until the flashing blue LED goes off, then release the button. 2. Now press and hold the pairing button for approximately 30 seconds, at which time the blue LED should be flashing rapidly. 3. Turn on the corresponding J&M Bluetooth headset, press and hold the multifunction button for approximately 30 seconds until the headset cycles from rapid blue flashing, to red flashing, and back to rapid blue flashing, at which time the headset is cleared and ready to pair to the dongle The headset and dongle07 are paired once the blue LED's on both the headset and the dongle07 flash slowly. 5. Turn the motorcycle ignition off. 6. Turn the headset off and then back on, press and hold the multifunction button for approximately13 seconds, until the blue LED flashes rapidly. 7. Select the hands-free menu on the GPS command center, go into the Bluetooth section and have it search for headset. When JM_CORP_HHS is displayed on the screen, click on it. When you are asked for a passkey, enter: Your GPS unit should now pair with the J&M Bluetooth headset.

6 8. Now pair your cell phone to the GPS command center, as per the linking/operation instructions included with your particular unit. 9. Turn the motorcycle ignition switch back on and the dongle07 will automatically reconnect to the Headset. 10. At this point both the dongle07 and the GPS command center should now be simultaneously linked to the headset. 11. Use the volume up/down buttons on the J&M Bluetooth headset to individually adjust the volume of the driver/passenger intercom, when two headsets 12. To set the music volume, adjust the music source volume that is feeding the dongle07 to a comfortable listening level. 14. To set the GPS command center navigation and/or cell phone conversation volume levels, refer to the operation instructions included with your particular unit. Additional cell phone volume adjustments can also be made on the cell phone itself, but during actual conversation only. 15. When placing or receiving a cell phone call, your headset will unlink from the dongle07 for the duration of the call, and then automatically re-pair with the dongle07 when the cell phone call is terminated. (maximum call duration of 59 minutes for this feature) Note: Because of Bluetooth bandwidth limitations, when your GPS command center and dongle07 are both simultaneously linked to your J&M Bluetooth headset, you may experience occasional cutting out or loss of data to the headset, which will not affect overall operation. 13. If your particular motorcycle audio system includes an 2003E-BW), reduce system (corded headset) intercom volume to minimum or 0. J&M Corporation Tucson, Arizona, U.S.A. Tel audio@jmcorp.com Thank you for the confidence you have shown in J & M by purchasing one of our innovative products. It will give you many hours of riding pleasure. If you have any questions during installation or require more information about this product, you may call our Customer service Department (English only, please) at , Monday through Friday, 8:00 a.m. to 5:00 p.m. Mountain Standard Time, U.S.A. WARRANTY REGISTRATION FORM Please fill out this card completely and mail it immediately after purchase. Please be sure that your zip code and serial number (if applicable) are legible. This will help us to serve you better. NOTE: Lift the velcro flap on the right speaker pouch to expose serial number. (PLEASE PRINT) Name Address City State Zip Motorcycle Other Make Model Year Product part number Serial number (if applicable) Date of purchase Mail to: J&M Corporation 1415 S. Cherry Avenue Tucson, AZ U.S.A. Name of dealer it was purchased from

7 WARRANTY AND REPAIR INFORMATION TWO YEAR LIMITED WARRANTY In order to facilitate the servicing of this warranty, the Warranty Registration Form should be filled out and returned within 10 days of the date of purchase. However, return of the Warranty Registration Form is not a precondition of this warranty, and this Warranty will be observed by J&M CORPORATION whether or not the Warranty Registration Form is returned, on the condition that other satisfactory evidence of the date of the original purchase is provided to J&M CORPORATION. WHO PROVIDES THE WARRANTY? This warranty is provided by J&M CORPORATION. WHO IS PROTECTED? This warranty is extended only to the original owner of this J&M CORPORATION product and may not be transferred or assigned. WHAT IS COVERED AND HOW LONG? This warranty covers all defects in material or workmanship of our product for a period of 2 years from date of original retail purchase. At its option, J&M CORPORATION will repair or replace any defective part(s) or equipment. The provisions of the warranty shall not apply to any unit which has been subjected to misuse, neglect, incorrect mechanical or electrical installation, unauthorized modifications, accident, nor to units which have been repaired or altered outside of our factory. PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY In the event that the product does not conform to this warranty, the product should be shipped prepaid to the J&M CORPORATION service facility. Transportation charges, insurance fees, and labor costs for shipment, removal, or reinstallation of our product are not covered by this warranty. Loss or damage in shipment is the sole responsibility of the freight carrier. FOR YOUR INFORMATION Repair as provided under this warranty is the exclusive remedy of the consumer. J&M CORPORATION shall not be liable for any incidental or consequential damages or for breach of any express or implied warranty on this product. Except to the extent prohibited by applicable law, any implied warranty of merchantability or fitness for a particular purpose on this product is limited in duration to the duration of the warranty. Some states do not allow the exclusion or limitation of incidental or consequential damages, or allow limitations on how long an implied warranty lasts, so the above limitations or exclusion may not apply to you. This warranty gives you specific legal rights which vary from state to state. J&M CORPORATION reserves the right to make changes in design and to make improvements in its products without the obligation to incorporate the changes or improvements in any of its previously manufactured products. J&M CORPORATION has not authorized anyone to make representations or warranties other than the warranty contained herein. The above warranty is effective for all products manufactured after 10/01/86. NON-WARRANTY REPAIR RATES J&M CORPORATION reserves the right to change the labor repair rates without prior notice. At the time of this printing the out-of- warranty repair is $40 per hour for labor only. However, the customer is advised to verify the current rate when he/she calls customer service to obtain the return authorization number. FACTORY SERVICE ADDRESS J&M Corporation, 1415 S. Cherry Avenue, Tucson, Arizona, 85713, U.S.A. Tel: audio@jmcorp.com CUSTOMER SERVICE NUMBER Please complete WARRANTY REGISTRATION FORM on the reverse side and send to J&M Corporation