SB1015W Widescreen All-in-one POS Terminal USER MANUAL

Transcription

1 SB1015W Widescreen All-in-one POS Terminal USER MANUAL

2 Table of Contents 1 Introduction Safety Information Electromagnetic compatibility statement Overview Features Appearances Outline Dimensions Rear panel I/O connectors Setup and Driver Installation Motherboard Headers and Jumpers Layout Motherboard Headers and Jumpers List Header/Jumper pin assignment Motherboard BIOS settings Touch screen driver installation Hardware Installation Magnetic Script Reader (MSR) Installation LCD Rear Display installation SATA Hard Disk Installation Troubleshooting Specifications

3 1 Introduction Thank you for purchasing the SB1015W all-in-one touch POS terminal. The SB1015W offers highly enhanced features, with easy connection to various optional devices for optimal performance. This easy-to-use POS terminal is designed to help you enhance your business flexibility and offer superior customer experience. Bematech is committed to continuously improve product quality and provide better after-sales service. In order to take full advantage of our devices, we strongly recommend that you take the time to read this manual before setting up software solution. Note: Information in this manual may change without prior notice. 1.1 Safety Information Before plug in the product, please make sure the power you provide meets the power requirements (such as voltage, frequency); Make sure the ground terminal of the power outlet is working properly. To avoid electric shocks, disconnect the power cord from the electrical outlet before relocating the system. Lightning may damage this product. During lightning storms, unplug the network cable, power cable and any other connections. Turn off power before connecting any devices (except USB devices) to the terminal. Do not attempt to open the chassis. You may be hurt by electric shock. For service, call your place of purchase. Do not spill liquid on the terminal. Do not place any objects into the ventilation holes of this product. It may cause short-circuit of the internal components and cause a fire or electric shock. After the terminal is stored below temperature of 10 C, please place it in room temperature (10-35 C) in the original packing for at least two hours to allow the terminal to restore to room temperature before operation. This is to avoid condensation that might cause electrical damage. Keep the terminal clean, dry, and away from dust, moisture and direct sunlight. Do not use harsh chemicals or strong cleaning solvents to clean the monitor 2

4 screen. Wipe it clean with a soft terry cloth applied with a mild solution Do not share the same power outlet with high-power electrical appliances; keep distance from high level magnetic interference. Do not the use sharp pointed objects to work with the touch screen to avoid damage to the screen. When the following occurs: Liquid gets inside the POS terminal; Accidental physical damage; The power cord or plug is damaged; POS terminal produces a burning smell; Immediately disconnect the power supply, unplug the power cord, and contact a qualified service technician. 1.2 Electromagnetic compatibility statement FCC NOTICE This device complies with Part 15 of FCC Rules. Operations are subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. EUROPEAN COMMUNITY (CE) MARK OF CONFORMITY This product is in conformity with the protection requirements of EU Council Directive 89/336/EEC on the approximation of the laws of the Member States relating to electromagnetic compatibility. Bematech / Logic Controls cannot accept responsibility for any failure to satisfy the protection requirements resulting from a non-recommended modification of the product. This product has been tested and found to comply with the limits for Class A Information Technology Equipment according to CISPR 22 / European Standard EN The limits for Class A equipment were derived for commercial and industrial environments to provide reasonable protection against interference with licensed communication equipment. 3

5 2 Overview 2.1 Features True-flat no-bezel 15.6" widescreen touch monitor Fanless operation High performance Intel quad core celeron processor J1900 Support DDR3L SO-DIMM 1066/1333 MHz up to 8GB Durable and sturdy base Easy to change or replace hard disk drive Optional integrated LCD/VFD customer display and 3-track MSR. 2.2 Appearances 2.3 Outline Dimensions 4

6 2.4 Rear panel I/O connectors At the rear panel of the SB1015W is a row of external I/O device connectors detailed as follows: USB 2.0 Ports Line-Out VGA Port Power Switch COM1 Port USB 2.0 Port COM2 Port RJ-45 LAN Port USB 3.0 Port Port Name Function DC-in 12V Power Connector USB 2.0 Port USB 3.0 Port VGA Port Serial Port RJ-45 LAN Port Line-Out Connector Power Switch Connect compatible power adapter to provide power supply for the system. Connect USB keyboard, mouse or other devices compatible with USB specification. Connect USB keyboard, mouse or other devices compatible with USB specification. USB 3.0 ports supports up to 5Gbps data transfer rate. Connect second display device that support VGA specification. Connect external devices that supports RS232 serial communications interface. Standard RJ-45 LAN jack for network connection. Connect external speaker, earphones, etc for system audio output. For switching on / shutdown system. 5

7 3 Setup and Driver Installation 3.1 Motherboard Headers and Jumpers Layout

8 3.2 Motherboard Headers and Jumpers List Header/Jumper Name 1 CPU Fan Header 2 F-Panel Header 3 USB 2.0 Header 4 ATX Power Header 5 SATA Header 6 CLR CMOS 7 SATA Power Header 8 COM1 / COM2 Header 9 COM1 / COM2 Voltage Jumper 10 COM2 RS-232 / 485 / 422 Jumpers 11 Back light Control Header 12 LVDS Voltage Jumper 13 LVDS Signal Header 14 LVDS Inverter Header 15 Internal Speaker Header 16 F-AUDIO Header 17 VGA Port Header 7

9 3.3 Header/Jumper pin assignment (1) CPU Fan Header (2) F-Panel Header Pin# Signal Pin# Signal 1 +HDD LED (VCC) 2 +Power LED (VCC) 3 GND 4 GND 5 GND 6 GND 7 RST_SW 8 PW_BN 9 NC 10 (3) USB 2.0 Header Pin# Signal Pin# Signal 1 VCC 2 VCC 3 DATA0-4 DATA1-5 DATA0+ 6 DATA1+ 7 GND 8 GND 9 NC (CUT) 10 GND (4) ATX Power Header 8

10 (5) SATA Header (6) CLR CMOS Jumper (7) SATA Power Header Pin# Signal 12V GND GND 5V (8) COM1 / COM2 Header (9) COM1 / COM2 Voltage Jumper JPCOM1 COM1 Pin9 1-2 Close 5V 3-4 Close 12V 5-6 Close Normal JPCOM2 COM Pin9 1-2 Close 5V 3-4 Close 12V 5-6 Close Normal (10) COM2 RS-232 / 485 / 422 Jumpers COM2 JP9 JP10 JP11 RS RS RS COM2 Pin 1(TXD) 2(RXD) 1(TXD-) 2 (TXD+) 3(RXD+) 4(RXD-) 9

11 (11) Back light Control Header (12) LVDS Voltage Jumper (13) LVDS Signal Header (14) LVDS Inverter Header (15) INVERTER (6-Pin): LVDS1 Inverter Header 10

12 (16) F-AUDIO Header Pin # Signal Pin # Signal 1 Mic in 2 Aud GND 3 Mic VREF 4 Void 5 FPOUT R 6 RET R 7 KEY (RSVD) 8 VOID 9 FPOUT L 10 RET L (17) VGA Port Header 11

13 3.4 Motherboard BIOS settings The POS terminal has a BIOS (Basic Input Output System) program located on a Flash Memory on the motherboard. This program is a bridge between motherboard and operating system. When you start the computer, the BIOS program will gain control. The BIOS first operates an auto-diagnostic test called POST (power on self test) for all the necessary hardware, it detects the entire hardware device and configures the parameters of the hardware synchronization. Only when these tasks are completed done it gives up control of the computer to operating system (OS). The terminal is loaded with default BIOS settings in the factory. change the parameters in the BIOS unless necessary. Please do not Entering Setup Power on the terminal and pressing <Del> immediately allows you to enter Setup. If you do not press the key at the correct time and the system does not enter Setup, turn off the terminal and try again Function Keys Press (left, right) to select screen; Press (up, down) to choose, in the main menu, the option you want to confirm or to modify. Press <Enter> to select. Press <+>/< > keys when you want to modify the BIOS parameters for the active option. [F1]: General help. [F2]: Previous value. [F9]: Optimized defaults. [F10]: Save & Reset. Press <Esc> to quit the BIOS Setup. 12

14 3.5 Touch screen driver installation For resistive touch version of SB1015W, follow the driver installation and calibration steps below. For PCAP touch version, no driver installation and calibration is required. 1. Navigate to the installer directory to find the setup.exe file. Double-click on setup.exe to start installation. 2. When installation starts, click [Next] to proceed to the next step. 3. Installation in progress 13

15 4. Uncheck Install PS/2 interface driver and click [Next] to continue installation. 5. Uncheck install RS232 interface driver and click [Next] to continue installation. 6. Select option NONE, click [Next] to continue installation. 14

16 7. If there are additional touch monitors connected, please check Support multi- monitor system. 8. Select the destination location to install the touch driver. The default path is C:\Program Files\eGalaxtouch. Click [Next] to continue installation. 9. Select the Program Folder to install the utility. The default is egalaxtouch. Click [Next] to continue installation. 15

17 10. Check the option to create a desktop shortcut icon. Click [Next] to continue. After install the driver successfully, identify the USB controller is installed as shown below. 11. Click on "Settings" tab to change the touch function settings as needed. 16

18 12. Perform touch calibration if necessary and use Draw Test to check touch accuracy after calibration. 17

19 4 Hardware Installation 4.1 Magnetic Script Reader (MSR) Installation (optional peripheral) 1. Remove the MSR mount cover from the monitor. 2. Insert MSR module. Make sure reader has been properly connect to the monitor USB port then use the 2 screws to fix the MSR. 18

20 4.2 LCD Rear Display installation (optional peripheral) 1. Use USB cable to connect the second display and install VESA bracket set to the LCD display with M4 screws (x4). 2. Remove the display mount cover from monitor. 3. Mount the LCD display assembly to the touch monitor and secure with screws. Plug USB cable into monitor USB port. USB port 19

21 4.3 SATA Hard Disk Installation 1. Remove the HDD mount cover from the back of monitor. 2. Install anti-shock rubbers to both sides of the SATA HDD. Plug SATA cable and power cable into SATA HDD connectors. 3. Insert the SATA HDD assembly to the monitor and reinstall HDD mount cover. Secure cover with the coin slot screw. 20

22 5 Troubleshooting 1. Terminal does not boot If the terminal cannot boot after repeated pressing of the power switch when connect to the power, the terminal power light remains off, the fan does not operate, and the BIOS beeping is not heard, it might be power supply problems. (a) Check the power adapter is plugged in correctly to the power outlet. (b) Check the connection between the terminal and the power adapter, and then re-boot the machine. (c) If the terminal is working in high temperature environment that causes the terminal automatically shut down in protection mode, please disconnect the power of the machine. Wait until environment temperature has dropped and restart. (d) If the terminal does not boot after a sudden power failure or illegal shutdown, unplug the adapter from the terminal, and press the power button several times. Then plug in the adapter and boot again. (e) If the adapter light blinks or go off, unplug the adapter immediately and do not plugged in again. Contact with our products service center. 2. The terminal automatically restart (or shutdown) If terminal is frequently automatic shutdown or auto-boot during operation (or boot up), (a) Check the power supply is connected properly; make sure the plug is not loose and contacts are in good condition; (b) Check if the AC line voltage is stable; (c) A sudden power failure or improper shutdown may cause this problem. Press F8 to boot system into safe mode and debug. (d) If any new hardware is added or replaced that caused this problem, remove the hardware and reboot; (e) If the above steps do not resolve this problem, reinstall the operating system. 21

23 3. The touch screen does not respond (a) Remove the touch driver and then install it again. (b) Execute the egalaxtouch utility and check if the interface port is working. 4. When touching the screen, cursor always returns to a fixed position. (a) Check if there is anything pressing on the touch screen. (b) Other high power or high frequency equipment may affect the screen or controller. Make sure that the touch screen is away from the high-voltage equipment. (c) The touch screen driver is not installed correctly, install the driver (please refer to the "Touch Screen Setup") and run a 25-point calibration. 5. Touch screen is not accurate Run the touch screen calibration program with a 25-point recalibration. We also recommend doing this after changing the monitor resolution or refresh rate. When running the calibration, touch the center of calibration point to assure accuracy. 6. The cursor moves opposite to the touch movement (a) Run the 4/9/25 point calibration. (b) The touch screen driver is not installed properly, reinstall the driver. 7. The cursor is fixed at the edge of LCD (a) Check if the edge of the screen is being pressed by something. (b) Check the edges of the LCD if there is anything jammed in the front bezel. (c) Make sure that the touch screen is clean. 8. The cursor in the touch screen can only move in a small area or touch positions are inaccurate. (a) This situation usually occurs first time after installing the driver. Please run the touch screen calibration program. We also recommend you to do this after changing monitor resolution. (b) Run the touch screen calibration program to do a 25-point recalibration. 22

24 6 Specifications MAIN BOARD CPU IO Chipset Memory Ethernet LAN Audio Storage Intel Celeron J1900 quad-core 2.0GHz IT8718F DDR3L 1333/ V SODIMM slot, up to 8GB Realtek RTL8111F PCI Express Gigabit LAN ALC662 HD Audio CODEC SATA 2.5 inch Hard Disk Drive/SSD, msata SSD DISPLAY LCD panel Touch screen Touch Controller 15.6" TFT display, WXGA 1366 x 768, 200 nits typ. 5-wire resistive, optional projected capacitive USB interface I/O PORTS USB ports Serial ports Ethernet Video port Audio port USB2.0 x4, USB3.0 x2 RS232 DB9 x2 Gigabit LAN, RJ45 x1 VGA DB15 x1 Line out x1 ELECTRICAL Power supply Input to power adapter External power adapter, DC 12V 80W min. 100 to 240VAC, 50/60Hz ENVIRONMENTAL Operating temperature Relative humidity 0 C to 40 C 8% to 80%, non-condensing MECHANICAL Dimensions (W x H x D) Weight 15.98" x 12.13" x 9.06" (406 x 308 x 230mm) 13.0lb (5.91Kg) OPTIONAL PERIPHERALS Customer Display MSR VFD 20 columns x 2 lines (USB) or 8" True-flat LCD (VESA holes 75x75, USB) JIS-I or II, ISO Track 1/2/3 (USB) 23

25 SB1015W Widescreen All-in-one POS terminal 24