DirectCommand Installation 5 Channel Spreader Control Module Technology

Transcription

1 DirectCommand Installation Ag Leader Technology Note: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number Quantity Direct Command Kit Cable Installation Kit Hardware Kit Large Module Quick Reference Card Dust Receptacle 2-Pin DTP Dust Plug 12-Pin DT (Key A) A 1 Corrugated Loom 1-in diameter 25 ft Installation Instructions 5 Channel Module Implement Cable 3 ft CAN Bus Stub 14 in Closed Loop Spinner Control Cable Spreader Control Cable 25 ft Spreader Control Cable 29 ft Chain Oiler Cable 7 ft Implement Adapter Cable Power Cable Display Cable Kit Power Control Relay Display Cable Boom Switch Box Kit Hardware Kit Deutsch Dust Plug 6-pin CAN Y-Splice CAN Bus Stub 1 ft Switch Box Bracket Switch Box Console Auxiliary Input Module Optional Items Remote Master Switch Dash Or Remote Master Switch Foot PN: Rev. C October 2013 Page 1 of 18

2 Ag Leader Technology DirectCommand Installation Important Notices You will save time and prevent wrong installation of components by closely following these step-by-step instructions. If you have questions, call Ag Leader Technology at Ext 1. Direction words (LEFT and RIGHT) are commonly used when describing an installtion procedure. Interpret direction words as if standing behind equipment and looking forward Signal words (CAUTION, IMPORTANT and NOTE) are provided to draw attention to information that is important for the safe/correct installation and operation of this product. CAUTION will alert you to situations that will impact the physical safety of you or others. IMPORTANT will alert you to the potential for damage to the product or loss of data. NOTE will provide you with additional information to simplify a procedure or clarify a process. This DirectCommand kit fits the following machines: Spinner Spreader machines with up to 5 separate control Channels Read all instructions first to familiarize yourself with the installation procedures. Keep parts list and installation instructions for use as a reference after completing installation. Page 2 of 18 October 2013 PN: Rev. C

3 DirectCommand Installation Ag Leader Technology Common Components This section contains illustrations of components common to all Direct Command Installations. Their purpose is to ensure proper identification and installations in the sections that follow. CAN Bus Connectors 1. Terminator PN: Plug (Not all applications) PN: Y-Splice PN: PN: Rev. C October 2013 Page 3 of 18

4 Ag Leader Technology DirectCommand Installation Component and Cable Layout Page 4 of 18 October 2013 PN: Rev. C

5 DirectCommand Installation Ag Leader Technology Safety Notices CAUTION: Turn off machine and wait for all motion to stop before starting work. Set parking brake. CAUTION: Be sure to wear proper eye protection when using any power tools, such as when drilling any mounting holes. IMPORTANT: Check behind vehicle and implement panels for any holes, wiring or controls that could be damaged when drilling any holes. IMPORTANT: Disconnect the Display, DirectCommand components and flow meter from electrical system when welding on equipment or jump starting unit to prevent component damage due to power surges or excessive current. IMPORTANT: If using a non Ag Leader GPS receiver, make sure to install a Null Modem Cable, included in the Display Kit, to prevent damage to the Display or GPS receiver. IMPORTANT: Use Dielectric grease to coat the seals and terminals of each connector that will be exposed to weather or chemicals as you plug them in. NOTE: Be sure to follow the alignment keys on the plugs and the receptacles carefully. Do not use excessive force when mating connectors. PN: Rev. C October 2013 Page 5 of 18

6 Ag Leader Technology Installing the Display DirectCommand Installation Parts required for procedure: (1) Ag Leader Integra Display PN: or (1) Edge Display PN: or (1) InSight Display PN: From Switch Box Kit (Optional) (1) Switch Box Hardware Kit PN: (1) Switch Box Bracket PN: Step-by-Step instructions for installing the Display 1. Place the display face down on a flat surface. If a 10-boom Switch Box will be used, place the metal switch box bracket over the four mounting holes on the back of the display, and then place the monitor mounting bracket on top of the switchbox bracket. If the Switch box will not be used, place the monitormounting bracket directly on the display. NOTE: The Switchbox may also be mounted independently of the Display with the Angle Brackets included in the Switch Box hardware kit. 2. Insert one Phillips Pan Head Screw with lock washer in each of the four holes and tighten firmly. Display with Switchbox and RAM Mount Installed 3. Mount the Display in a convenient place for operation, but out of the operator s line of sight while driving the vehicle. Page 6 of 18 October 2013 PN: Rev. C

7 DirectCommand Installation Ag Leader Technology Installing the Auxiliary Input Module Step-by-Step instructions for installing the Auxiliary Input Module Parts required for procedure: From Switch Box Kit or Auxiliary Input Module Kit (1) Dust Plug 6 pin PN: (1) Auxiliary Input Module PN: Optional Items Purchased Separately (1) Module Mounting Plate PN: (1) Raven Radar Adapter PN: (1) Dickey-John Radar Adapter PN: Find a location to mount the Auxiliary Input Module in the vehicle cab, so that it is out of the operator s way, but easily accessible for any troubleshooting. NOTE: A Module Mounting Plate, PN: may be purchased separately to help mount the Auxiliary Input Module. 2. If a radar is installed on the vehicle, choose the proper Radar Adapter Cable, and connect the gray plug into the receptacle labeled RADAR on the Auxiliary Input Module. If a radar backup is not going to be used, plug the gray 6-pin dust plug into the RADAR connection on the Auxiliary Input Module. Installing the Switch Box or Master Switch Step-by-Step instructions for installing the Switch Box or Master Switch Parts required for procedure: (1) 10 Section Switch Console PN: or (1) Remote Master Switch Dash PN: or (1) Foot Pedal Kit PN: NOTE: A Master switch is required for operation of the Spinner Spreader Control Module. This can be done with a 10 section switchbox, PN: , a Remote Master Switch, PN: , a Foot Pedal Kit, PN: or a master switch in the vehicle. If switches are desired to independently operate the spreader control channels, a 10 section switchbox or machine switches must be used. 1. If a Foot Pedal Master switch is used, refer to installation instructions PN: included in the Foot Pedal Kit for proper installation of the Foot Pedal. PN: Rev. C October 2013 Page 7 of 18

8 Ag Leader Technology DirectCommand Installation NOTE: Steps 2-6 are for installing a 10-section switchbox. 2. Align the two holes in the back of the Switch Console, PN: with the bottom two holes on the Switchbox bracket already mounted on the display. 3. Using the hardware provided in the Switchbox Hardware Kit, fasten the Switchbox to the Switchbox Bracket. 4. Route the cable coming from the Switchbox towards the Auxiliary Input Module. 5. Connect the green 12-pin Deutsch plug into the receptacle marked SWITCH A on the Auxiliary Input Module. 6. Connect the brown 12-pin Deutsch plug into the receptacle marked SWITCH B on the Auxiliary Input Module. NOTE: Steps 7-9 are for installing a Remote Master Toggle Switch. 7. Mount the Remote Master Toggle Switch, PN: in a convenient location for the operator. 8. Route the opposite end of the cable towards the Auxiliary Input Module and connect the green 12-pin Deutsch plug into the receptacle marked SWITCH A on the Auxiliary Input Module. 9. Use the gray 12-pin Deutsch Dust plug included in the Auxiliary Input Module Kit to seal the receptacle marked SWITCH B on the Auxiliary Input Module. Page 8 of 18 October 2013 PN: Rev. C

9 DirectCommand Installation Ag Leader Technology Installing the 5- Channel Spreader Control Module Step-by-Step instructions for installing the 5- Channel Spreader Control Module Installing the CAN Bus Harness Parts required for procedure: From 5 Channel Spinner Spreader Control Module Kit (1) Spinner Spreader Control Module PN: (1) Hardware Kit Large Module PN: The 5-Channel Spinner Spreader Control Module may be mounted at the operator s discretion. Make sure it is located in a place that all the control cables will reach, and out of the way of moving parts. The recommended location is one of the front right vertical side sheets. 2. Using the module as a template, drill 1/4" diameter holes. Use 1/4" stainless steel hardware provided in the Hardware Kit PN: to secure the module into place. Parts required for procedure: From Display Cable Kit (1) Power Control Relay PN: (1) Display Cable PN: From 5-Channel Spinner Spreader Control Module Kit (1) Dust Cap 2 pin PN: (1) Implement Cable 3 ft. PN: (1) CAN Bus Stub 14 in. PN: (1) Implement Adapter Cable PN: (1) Power Cable PN: From the Auxiliary Input Module Kit or Switch Box Kit (1) CAN Y-Splice PN: (1) CAN Bus Stub 12 in. PN: Optional Items Purchased Separately Implement Cable Extension, 6 ft PN: Implement Cable Extension, 12 ft PN: Implement Cable Extension, 24 ft PN: Implement Cable Extension, 36 ft PN: PN: Rev. C October 2013 Page 9 of 18

10 Ag Leader Technology Step-by-Step instructions for installing the CAN Bus Harness DirectCommand Installation 1. Connect the Power Control Relay, PN: , to the square 4-pin Weatherpack Shroud on the Display Cable, PN: Press the Power Control Relay until the latch clicks, locking the relay in place. 2. Connect the round 28-pin connector on the Display Cable to the connector on the back of the InSight or EDGE Display, or the connector labeled MAIN on the back of the Ag Leader Integra display. 3. Route the opposite end of the Display Cable towards the Auxiliary Input Module. 4. Connect the single end of the CAN Y-Splice PN: , from the Auxiliary Input Module Kit or Switch Box Kit into the 4-pin CAN connector on the Display Cable. 5. Connect the black 4-pin plug on the 12-in. CAN Bus Stub, PN: into the gray side of the CAN Y-Splice. 6. Plug the opposite end of the CAN Bus Stub into the receptacle labeled CAN BUS on the Auxiliary Input Module. 7. Connect the ring terminals on the Power Cable, PN: to the battery, or power studs in the cab. Connect the ring terminal with fuses to the positive terminal, and connect the ring terminal with black wires to the battery ground. 8. Route the opposite end of the Power Cable towards the Auxiliary Input Module. 9. Plug the 3-pin Weatherpack tower on the Power Cable into the mating shroud on the Display Cable. 10. Connect the 4-pin CAN plug on the Implement Adapter Cable, PN: into the black side of the CAN Y-Splice. 11. Connect the 2-pin gray Deutsch receptacle into the 2-pin gray plug on the Power Cable. 12. Route the round 16-pin plug on the opposite end of the Implement Adapter Cable out of the cab. NOTE: If a hole must be cut for routing the cable out of the cab, make sure to re-seal the hole after the cable is routed to keep vehicle cab airtight from chemicals being applied. Page 10 of 18 October 2013 PN: Rev. C

11 DirectCommand Installation Ag Leader Technology 13. Connect the 4-pin gray Deutsch plug on the 14 in CAN Bus Stub, PN: into the gray 4-pin on the 5-channel Spinner Spreader Control Module. 14. Connect the opposite end of the CAN Bus Stub into the gray side of the CAN Y-Splice installed on the Implement Cable, PN: Connect one of the 2-pin gray plugs on the Implement Cable into the 2-pin receptacle coming out of the Spinner Spreader Control Module. 16. Install the 2-pin Deutsch Dust Cap, PN: to seal the second gray plug on the Implement Cable 17. Connect the grounding ring terminal on the Implement Cable to a grounding point on the machine or implement frame. 18. Route the opposite end of the Implement Cable towards the front of the implement or spreader bed, so it can be connected to the Implement Adapter Cable. If necessary, extension cables may be purchased for additional length. Refer to the table below for available lengths. Length Part Number 6 ft ft ft ft Implement Cable Extensions PN: Rev. C October 2013 Page 11 of 18

12 Ag Leader Technology Installing the Control Cables Step-by-Step instructions for installing the Control Cables DirectCommand Installation Parts required for procedure: (1) Corrugated Loom 1 dia 25 ft PN: (1) Spinner Control Cable 28 ft PN: (3) Spreader Control Cable 25 ft PN: (1) Spreader Control Cable 29 ft PN: (1) Chain Oiler Cable 7 ft. PN: NOTE: For the purpose of these installation instructions and module operation, Channel 1, or Bin #1 are numbered by the product bins and controls counting up from the front to the back of the machine. 10. Connect the Black 12-pin Plug of the Spinner Control Cable PN: to the mating receptacle on the 5 Channel Control Module 11. Route both connectors on the opposite end of the Spinner Control Cable under the front end of the spreader bed and connect the 2- pin Weatherpack tower of the Spinner Control Cable to the mating Shroud on the Spinner Control Valve. Spinner Control Valve 12. Continue routing cable with 3-pin Weatherpack tower along the hydraulic lines on the left side of the spreader bed. Temporarily zip-tie cable to hydraulic lines. 13. Route the 3-pin Weatherpack cable underneath the fan assembly, securing the cable to the frame so that it will not get caught in moving parts. Page 12 of 18 October 2013 PN: Rev. C

13 DirectCommand Installation Ag Leader Technology 14. Connect the 3-pin Weatherpack tower to the mating connector on the Fan Speed Sensor. Bottom Arrow Points to Fan Speed Sensor Connection 15. Connect the gray 12-pin plug of the 29 ft. Spreader Control Cable, PN: to the Channel 1 connector in the lower left hand corner of the 5-Channel Spreader Module. 16. Route all three connections on the opposite end of the cable along the Spreader Control Cable previously routed. Connect the 3-pin Metripack tower into the mating connector on the main Conveyor control valve located towards the front of the left side of the spreader bed. Main Conveyor Control Valve PN: Rev. C October 2013 Page 13 of 18

14 Ag Leader Technology DirectCommand Installation 17. Continue routing the 4-pin Weatherpack tower and 3-pin Weatherpack shroud down the hydraulic lines, next to the previously routed cables. 18. Plug the 4-pin Weatherpack Tower into the mating shroud connected to the Bin Level Sensor for Bin # Route the 3-pin Weatherpack shroud along the framework to the right rear corner of the spreader bed, securing cable away from moving parts, and connect to the 3 pin Weatherpack tower on the #1 Conveyor Encoder. Top arrow points to #1 Conveyor Belt Encoder Connection 20. Plug the gray 12-pin plug of the 25 ft Spreader Control Cable, PN: into the Channel 2 connection on the 5-Channel Spreader Control Module. 21. Route the 3-pin Metripack connector of the Spreader Control Cable towards the control valve for Bin #2, located on the right side of the spreader bed, and connect to the mating Metripack Shroud. NOTE: If necessary, follow the hydraulic lines from the control valves to the hydraulic motors to verify which valve controls each hydraulic motor. Page 14 of 18 October 2013 PN: Rev. C

15 DirectCommand Installation Ag Leader Technology Bin #2 and #3 Control Valves 22. Route the 3-pin Weatherpack Shroud and Square 4-pin Weatherpack Tower around the front end of the spreader bed and down the left side of the bed along side the previously routed cables. 23. Connect the Square 4-pin Weatherpack Tower to the Bin Level Sensor Cable coming from Bin # Connect the 3-pin Weatherpack Shroud to the #2 Conveyor Belt Encoder. Control Cables connected to Conveyor Belt Encoders 25. Repeat Steps with additional Spreader Control Cables PN: for the Channel 3 and 4 control circuits. PN: Rev. C October 2013 Page 15 of 18

16 Ag Leader Technology DirectCommand Installation 26. Connect the Green 12-Pin Plug of the Chain Oiler Cable, PN: to the mating receptacle on the 5-Channel Spreader Control Module. 27. Route the opposite end of the Chain Oiler Cable across the front end of the spreader along the previously routed cables. 28. Connect the 2-pin Weatherpack Shroud to the mating Tower on the Chain Oiler Pump. Chain Oiler Weatherpack Connection 29. Remove the temporary cable ties installed with the cables along the front and left side of the spreader bed. 30. Slide the 1-inch diameter corrugated loom, PN: over all the installed cables routed from the module to the sensors on the back left corner of the spreader bed. 31. Use cable ties to secure the bundle of cables and corrugation avoiding pinch points and moving parts. Page 16 of 18 October 2013 PN: Rev. C

17 DirectCommand Installation Ag Leader Technology Setting Up the Display 1. Refer to the Quick Reference Guide, PN: for setting up the Display. 2. Enter the default settings from the following charts for the initial setup. Setting Name Control Valve Configuration Controller Settings Spinner Tab Default Description Value PWM Setting specifies the type of control valve being used for the rate control functions of the controlling system. PWM Frequency 100 Gain* 100 The frequency that the PWM control valve is pulsed at. Settings can be found from the manufacturer of the valve. Typical settings range from Hz. Determines how aggressively the control valve responds when making spinner speed adjustments. The higher the value the more aggressive the system response is. NOTE: Leaving all other valve control settings at the default value and making a small adjustment to the Gain is usually all that is required to fine-tune the control system. Zero RPM Offset Fan Speed Cal Auto Control Check Box 30 4 Default is unchecked Represents the maximum duty cycle that is sent to the control valve without producing any hydraulic flow from the PWM valve. Using too high of a Zero RPM Offset value can cause the spinner system to not properly shut off. See the PWM valve manufacturer information for recommended settings. The number of pulses that are generated by the sensor during one revolution of the spinner dish. Checking the Auto Control check box allows you to control the spinner speed. PN: Rev. C October 2013 Page 17 of 18

18 Ag Leader Technology Setting Name Control Valve Configuration DirectCommand Installation Controller Settings Channel Tab Default Description Value Servo Setting specifies the type of control valve being used for the rate control functions of the controlling system. Response Threshold Valve Response 1 Valve Response 2 Allowable Error Shaft Speed Cal Max Conveyor Speed % Determines where the control channel switches between using Valve Response 1 and Valve Response 2 speed setting. Leaving all other valve control settings at the default value and making a small adjustment to this setting is usually all that is required to fine-tune system performance. Decreasing this value will have the overall effect of speeding up servo valve response. Increasing this value will have the overall effect of slowing servo valve response. Determines the speed of the servo valve when product control error exceeds the Response Threshold setting. Valve Response 1 represents the fast speed of the servo valve. Decreasing the value will cause the servo valve to run slower. Determines the speed of the servo valve when product control error is less than the Response Threshold setting. Valve Response 2 represents the slow speed of the servo valve. Decreasing the value will cause the servo valve to run slower. Determines the percent of error that is allowed prior to the product control system making any flow rate changes. 2% - 3% is the normal dead band setting range. Too low of a setting value can cause the product control system to continually hunt for the target application rate. Too high of a setting will cause excessive product application error. Calibration number representing the pulses that equal one revolution of the rate control metering system. Setting determines the maximum RPM of the conveyor that controls product distribution to the application point. Page 18 of 18 October 2013 PN: Rev. C