um-fpu64 Floating Point Coprocessor 28-pin Breakout Board Introduction Bare um-fpu64 28-pin Breakout Board
|
|
|
- Morgan Stevens
- 5 years ago
- Views:
Transcription
1 Floating Point Coprocessor Breakout Board Introduction The breakout board has all of the required connections, and provides access to all um- FPU64 pins. It can be used as a development board or for permanently mounting in a project. The features include: all required connection for the interface selector and connector with resistors for SPI or I 2 C connections serial connector for access to SERIN and SEROUT pins serial connector is compatible with SparkFun FDTI Basic Breakout and Parallax PropPlug Power or Busy Status LED space provided for RTC oscillator and capacitors breakout connector for D0-D4 breakout connector for D5-D8 and AN0-AN5 optional I 2 C pull-up resistors for D0 and D board can be powered from USB during development Bare Breakout Board Micromega Corporation Revised
2 Installing the Required Components The following components are required for all configurations. - socket for - 0uF Tantalum capacitor (low ESR) 2-0. uf capacitors 2 - resistors - LED (note: + anode (long lead) is on the left) various 0. headers D4 D3 D2 D D0 D-I2C DO-I2C 0 uf EN MCL AN0 AN D5 D6 D8 BSY Male or female headers can be installed for each of the breakout connectors and jumpers. The following photo shows the breakout board after the required components and headers have been installed, and a right-angle header has been installed for the serial connector. See the Serial Connection section for additional information regarding the serial connector. Power Selector and LED Resistor The breakout board can be configured to draw power from the serial connector pin, or the interface connector pin. The interface connector should be used for power when connecting the to other components, since the serial connector can only supply a limited amount of current. Using the serial connector to supply power is convenient for development, since no external power supply is required, but care should be taken to ensure that the current requirements of your circuit are within the limits that can be provided by the serial connection. The LED can be configured as a power on indicator, or as a busy indicator, depending on the placement of the Micromega Corporation 2 Breakout Board
3 330 ohm resistor. When configured for power on, the LED turns on whenever is applied to the VDD pin. When configured as a busy indicator, the LED turns on when the /BUSY pin is low. Power from Serial Connector - pin Power from Interface Connector - pin Power Selector D4 D3 D2 D D0 D-I2C DO-I2C 0 uf EN MCL AN0 AN D5 D6 D8 BSY LED Resistor No LED connection LED shows Power On LED Shows Busy Status SPI Interface To configure the board for using an SPI interface, set the SEL jumper and add the resistor if using a 2-wire interface. The microcontroller connections are shown for each type of SPI interface. Interface Connector and Resistors D4 D3 D2 D D0 D-I2C DO-I2C 0 uf EN MCL AN0 AN D5 D6 D8 BSY SEL Jumper I2C SEL SPI Select SPI Interface Micromega Corporation 3 Breakout Board
4 SPI Bus Interface No resistors are installed when using an SPI Bus interface. Interface Connector Microcontroller / / SCK MISO MOSI SPI 3-wire Interface No resistors are installed when using an SPI 3-wire interface. Interface Connector Microcontroller / / SCK MISO MOSI SPI 2-wire Interface The resistor is installed when using an SPI 2-wire interface. Interface Connector Microcontroller / / CLK N/C DATA Micromega Corporation 4 Breakout Board
5 I 2 C Interface To configure the board for using an I 2 C interface, set the SEL jumper and configure the pull-up resistors as required. The microcontroller connections are shown. Interface Connector and Resistors D4 D3 D2 D D0 D-I2C DO-I2C 0 uf EN MCL AN0 AN D5 D6 D8 BSY SEL Jumper I2C SEL SPI Select I 2 C Interface No Pull-ups Pull-ups Interface Connector Microcontroller / / N/C N/C Serial Connection The serial connector is used to connect to the SERIN and SEROUT pins of the. The pinout of the connector has been designed to be compatible with two commonly available USB to serial interface boards: SparkFun FDTI Basic Breakout - (SparkFun part number DEV-08772) A 6-pin right-angle 0. male header should be installed in the outer six holes for the SparkFun FDTI Basic Breakout. Parallax Prop Plug (Parallax Item #3220) A 4-pin right-angle 0. male header should be installed in the inner four holes for the Parallax Prop Plug. Other USB to serial boards can also be used, but will likely require some custom wiring to change the pinout to be compatible with one of the serial connectors. A pull-down resistor is connected to the SERIN pin, so if nothing is plugged into the serial connector pins when the in reset, the debug monitor will be disabled. Micromega Corporation 5 Breakout Board
6 D4 D3 D2 D D0 D-I2C DO-I2C 0 uf EN MCL AN0 AN D5 D6 D8 BSY Serial Connector SparkFun FDTI Basic Parallax Prop Plug Example using FDTI Basic Breakout - Micromega Corporation 6 Breakout Board
7 Other Connections D0/D I 2 C Pull-ups D4 D3 D2 D D0 D-I2C DO-I2C 0 uf EN MCL AN0 AN D5 D6 D8 BSY RTC Crystal D0/D I 2 C Pull-ups The D0/D pull-up resistors are provided to facilitate using these pins for connecting devices to a local I2C bus. Jumpers D0-I2C and D-I2C are provided to enable or disable the pull-up resistors. D-I2C DO-I2C D-I2C DO-I2C Not Enabled Enabled RTC Crystal Oscillator If the real-time clock is used, the crystal and two capacitors must be installed. D0-D4 Breakout Connector A 7-pin connector is provided for the D0-D4 pins. D4 D3 D2 D D0 PCB Label Pin D4 D4/RTC D3 D3 D2 D2 D D VSS VDD Micromega Corporation 7 Breakout Board
8 A0-A5 and D5-D8 Breakout Connector A 0-pin connector is provided for the A0-A5 and D5-D8 pins. The /MCLR and /BUSY pins are also brought out to this connector. MCL AN0 AN D5 D6 PCB Label MCL AN0 AN D5 D6 BSY D8 BSY Pin VSS /MCLR AN0/VREF+ AN/VREF- D5/AN2 D6/AN3 /AN4 D8/AN5 /BUSY VSS Note: Since /MCLR is connected to through a pull-up resistor, the can be reset by briefly connecting the MCL pin to ground. Since the pin is next to the MCL pin, a post shunt can easily be used to briefly connect MCL to. Connector Two extra ground pins are provided. Reset Enable Jumper This option connects the pin from the serial connector to the /MCLR pin. This jumper should not be installed, since this capability is not currently supported by the the IDE. EN Schematic Diagram A schematic diagram is available as a separate document entitled. See: Breakout Schematic.pdf Micromega Corporation 8 Breakout Board
9 Parts List The parts for the breakout board are listed below, with Digi-Key part numbers included for reference purposes. All of the parts can be replaced with equivalent parts from other suppliers, and many of the parts may already be in your parts bin. Some parts can be omitted depending on the interface connection and the options selected. Qty Description Use Digi-Key Part Number Socket, Capacitor, 0 uf Tantalum Capacitor, 0. uf Ceramic Resistor, /8W Resistor, /8W (see note ) Power Power /MCLR pull-up SERIN pulldown I 2 C pull-ups ED3328-ND ND ND CF8JT0CT-ND CF8JT4K70CT-ND Resistor, /8W (see note 2) 2-wire SPI CF8JT00CT-ND Resistor, 330 /8W LED 3mm Green Diffused Crystal, (see note 3) Power/Busy LED Power/Busy LED RTC CF8JT330RCT-ND ND X24-ND 2 Capacitor, 22 pf Ceramic (see note 3) RTC ND Header, 0. Right-angle 40-position 6-pin or 4-pin Serial Connector SEC-40-ND Header, 0. Straight 40-position 0-pin, 7-pin, 6-pin, 3-pin, 3-pin, 2-pin Connectors and Jumpers S02EC-40-ND 4 Post Shunt, 0. Low-profile Jumpers A26232-ND. The resistors should only be installed if the I 2 C interface is used, and pull-ups are not already provided by the connecting device. 2. The resistor should only be installed if the 2-wire SPI interface is used. 3. The crystal and 22 pf capacitors are only required if the real-time clock is used. Further Information See the Micromega website ( for additional information regarding the floating point coprocessor, including: Datasheet Instruction Set Micromega Corporation 9 Breakout Board
um-fpu Application Note 9 Adding a Serial Connection to um-fpu V2
um-fpu Application Note 9 Adding a Serial Connection to um-fpu V2 This application note describes various methods of adding a serial connection to the um-fpu to provide support for debugging um-fpu code
MAX31723PMB1 Peripheral Module
19-6332; Rev 0; 5/12 MAX31723PMB1 Peripheral Module General Description The MAX31723PMB1 peripheral module provides the necessary hardware to interface the MAX31723 digital thermometer and thermostat to
Shack Clock kit. U3S Rev 2 PCB 1. Introduction
Shack Clock kit U3S Rev 2 PCB 1. Introduction Thank you for purchasing the QRP Labs Shack Clock kit. This clock uses the Ultimate3S QRSS/WSPR kit hardware, but a different firmware version. It can be used
Part Number: PCB-STM32-F4B1 (unpopulated PCB with Discovery module sockets, no other parts) STM32-F4B1 (assembled board, not presently available)
PCB-STM32-F4B1 Development baseboard for the STMicro Discovery-F4 module (STMicro part# STM32F4DISCOVERY) PCB Rev 1.00 shown. PCB Rev 1.20 has on-board RS232 drivers. Part Number: PCB-STM32-F4B1 (unpopulated
PCB-STM32-F3U. Development baseboard for the STMicro Discovery-F3 module (STMicro part# STM32F3DISCOVERY)
PCB-STM32-F3U Development baseboard for the STMicro Discovery-F3 module (STMicro part# STM32F3DISCOVERY) Part Number: PCB-STM32-F3U (unpopulated PCB with Discovery module sockets, no other parts) STM32-F3U
Prototyping Module Datasheet
Prototyping Module Datasheet Part Numbers: MPROTO100 rev 002 Zenseio LLC Updated: September 2016 Table of Contents Table of Contents Functional description PROTOTYPING MODULE OVERVIEW FEATURES BLOCK DIAGRAM
8051 Intermidiate Development Board. Product Manual. Contents. 1) Overview 2) Features 3) Using the board 4) Troubleshooting and getting help
8051 Intermidiate Development Board Product Manual Contents 1) Overview 2) Features 3) Using the board 4) Troubleshooting and getting help 1. Overview 2. Features The board is built on a high quality FR-4(1.6
Arduino Uno. Arduino Uno R3 Front. Arduino Uno R2 Front
Arduino Uno Arduino Uno R3 Front Arduino Uno R2 Front Arduino Uno SMD Arduino Uno R3 Back Arduino Uno Front Arduino Uno Back Overview The Arduino Uno is a microcontroller board based on the ATmega328 (datasheet).
FUNCTIONAL BLOCK DIAGRAM DIGITAL POWER SUPPLY +5V +3.3V EXT. EXTERNAL ANALOG POWER SUPPLY V LOGIC V DD V SS SPI INTERFACE RDY RESET AD5292 GND
Evaluation Board for the 10-Bit, Serial Input, High Voltage Digital Potentiometer EVAL-AD5292EBZ FEATURES Full-featured evaluation board for the AD5292 Wiper buffer 4-wire ohm measurement capability Various
Rapid28iXL PIC Prototyping PCB User Manual
Description Features This is a PCB designed to facilitate the rapid prototyping of a device based on a 28 pin Microchip PIC microcontroller. To allow users to focus on their application, we take care of
ST SPC58 B Line Emulation Adapter System
_ V1.1 Hardware Reference ST SPC58 B Line Emulation Adapter ST SPC58 B Line Emulation Adapter System ST SPC58 B line emulation adapter primary use case is providing Nexus trace functionality for the SPC58
Rapid40iXL PIC Prototyping PCB User Manual
Description This is a PCB designed to facilitate the rapid prototyping of a device based on a 40 pin Microchip PIC microcontroller. To allow users to focus on their application, we take care of key housekeeping
Modtronix Engineering Modular Electronic Solutions SBC28DC. Single board computer for 28 pin DIP PICs
Modtronix Engineering Modular Electronic Solutions Single board computer for 28 pin DIP PICs Table of Contents 1 Introduction...2 2 Features...4 3 Expansion Connectors...5 3.1 Daughter Board Connectors...5
MAX5216PMB1 Peripheral Module
9-6; Rev 0; 5/ MAX56PMB Peripheral Module General Description The MAX56PMB peripheral module provides the necessary hardware to interface the MAX56 6-bit DAC to any system that utilizes PmodK-compatible
Propeller Project Board USB (#32810)
Web Site: www.parallax.com Forums: forums.parallax.com Sales: sales@parallax.com Technical: support@parallax.com Office: (916) 624-8333 Fax: (916) 624-8003 Sales: (888) 512-1024 Tech Support: (888) 997-8267
A4988 Stepper Motor Driver Carrier, Black Edition
A4988 Stepper Motor Driver Carrier, Black Edition A4988 stepper motor driver carrier, Black Edition, bottom view with dimensions. Overview This product is a carrier board or breakout board for Allegro
Sierra Radio Systems. Digital Compass. Reference Manual. Version 1.0
Sierra Radio Systems Digital Compass Reference Manual Version 1.0 Contents Digital compass board RS485 power injector For more information, go to the Sierra Radio Systems web site at www.sierraradio.net
PIC 28 Pin Board Documentation. Update Version 5.0
PIC 28 Pin Board Documentation Update 2009.10 Version 5.0 Table of Contents PIC 28 Pin Board Documentation... 1 Table of Contents... 2 Introduction... 3 Circuit Schematic... 4 The following is the Circuit
Rapid40i PIC Prototyping PCB User Manual
Description This is a PCB designed to facilitate the rapid prototyping of a device based on a 40 pin Microchip PIC microcontroller. To allow users to focus on their application, we take care of key housekeeping
Pmod modules are powered by the host via the interface s power and ground pins.
1300 Henley Court Pullman, WA 99163 509.334.6306 www.store. digilent.com Digilent Pmod Interface Specification 1.2.0 Revised October 5, 2017 1 Introduction The Digilent Pmod interface is used to connect
WICE-SPI Hardware Operation Manual
WICE-SPI Hardware Operation Manual 1. Hardware Instruction 1. WICE-SPI processes data transmission, programming or emulation through USB 2.0 interface and does not need external power. 2. WICE-SPI is equipped
EVAL-ADG2128EB. Evaluation Board I 2 C CMOS, 8 12 Analog Switch Array with Dual/Single Supplies FEATURES DESCRIPTION
Evaluation Board I 2 C CMOS, 8 12 Analog Switch Array with Dual/Single Supplies EVAL-ADG2128EB FEATURES Full featured evaluation board for ADG2128 Various link options Direct hook up to USB port of PC
KPIC-0818P (V050919) Devices Included in this Data sheet: KPIC-0818P
Devices Included in this Data sheet: KPIC-0818P Features: Carefully designed prototyping area Accepts 8 pin PIC12 series micro-controllers Accepts 14 and 18 Pin PIC16 series Accepts some 8,14 and 18 pin
A4988 Stepper Motor Driver Carrier
A4988 Stepper Motor Driver Carrier A4983/A4988 stepper motor driver carrier with dimensions. Overview This product is a carrier board or breakout board for Allegro s A4988 DMOS Microstepping Driver with
ARDUINO MICRO WITHOUT HEADERS Code: A000093
ARDUINO MICRO WITHOUT HEADERS Code: A000093 Arduino Micro is the smallest board of the family, easy to integrate it in everyday objects to make them interactive. The Micro is based on the ATmega32U4 microcontroller
AAZ-0914A USB, Blue tooth and Graphic CPU 50MHZ Antenna Analyzer
Fox Delta Amateur Radio Projects & Kits FD- AAZ-0914A AAZ-0914A USB, Blue tooth and Graphic CPU 50MHZ Antenna Analyzer AAZ- 0914A KIT: USB Standalone, Blue tooth standalone and Graphic CPU capable 50MHZ*
AVR Intermediate Development Board. Product Manual. Contents. 1) Overview 2) Features 3) Using the board 4) Troubleshooting and getting help
AVR Intermediate Development Board Product Manual Contents 1) Overview 2) Features 3) Using the board 4) Troubleshooting and getting help 1. Overview 2. Features The board is built on a high quality FR-4(1.6
Adafruit Terminal Block Breakout FeatherWing
Adafruit Terminal Block Breakout FeatherWing Created by lady ada Last updated on 2017-01-04 04:53:26 AM UTC Guide Contents Guide Contents Overview Pinouts Assembly Downloads Datasheets & Files Schematic
JeeNode V2. A small *duino-ish MPU board with a wireless RF module. Jean-Claude Wippler jeelab.equi4.com March 2009
JeeNode V2 A small *duino-ish MPU board with a wireless RF module Overview Jean-Claude Wippler jeelab.equi4.com March 2009 The JeeNode is a small micro-controller board which can be used for a variety
Atmel AVR datasheet. Matrix Multimedia Atmel AVR Board EB Contents
Atmel AVR datasheet Contents 1. About this document 2. General information 3. Board overview 4. Getting Started 5. Block schematic and description Appendix A. Circuit diagram B. Compatible AVR device C.
VFO/Signal Generator kit PCB Revision QCU Rev 1 or QCU Rev 3
1. Introduction VFO/Signal Generator kit PCB Revision QCU Rev 1 or QCU Rev 3 Thank you for purchasing this QRP Labs kit. The QRP Labs kit range is modular. The kit uses the same PCB and bag of components
Shack Clock kit PCB Revision: QCU Rev 1 or QCU Rev 3
1. Introduction Shack Clock kit PCB Revision: QCU Rev 1 or QCU Rev 3 Thank you for purchasing this QRP Labs Shack Clock kit. The kit uses the same PCB and bag of components as some other QRP Labs kits.
Adafruit USB Power Gauge Mini-Kit
Adafruit USB Power Gauge Mini-Kit Created by Bill Earl Last updated on 2017-07-14 11:55:04 PM UTC Guide Contents Guide Contents Overview Assembly Basic Assembly Solder the female connector. Solder the
S USB-PC Connection (Cable Not Included) S USB Powered (No External Power Supply Required) S Real-Time Data Acquisition Through the USB
19-5610; Rev 1; 8/11 MAXADClite Evaluation Kit General Description The MAXADClite evaluation kit (EV kit) evaluates the MAX11645, Maxim's smallest, very-low-power, 12-bit, 2-channel analog-to-digital converter
Arduino ADK Rev.3 Board A000069
Arduino ADK Rev.3 Board A000069 Overview The Arduino ADK is a microcontroller board based on the ATmega2560 (datasheet). It has a USB host interface to connect with Android based phones, based on the MAX3421e
reserved pulse width stim freq int/ext trig Amplitude
0 1 2 3 4 5 6 7 8 +5V A A +5V 1 RA1 10kOhm B 2 3 4 5 6 7 8 9 B C D J2 6P4C (RJ11) To PC R5 470ohm U2 4N33 X1 RESONATOR 4 MHz U1 14 Vdd 5 Vss 4 RB7 MCLR/ RB6 RB5 RB4 6 INT/RB0 RB2 16 RB1 OSC1 15 OSC2 PIC16F84_1
+Denotes lead-free and RoHS compliant.
19-4387; Rev 0; 11/08 MAX9675 Evaluation Kit General Description The MAX9675 evaluation kit (EV kit) provides a proven design to evaluate the MAX9675 nonblocking 16 x 16 video crosspoint switch with buffered
ARDUINO UNO REV3 SMD Code: A The board everybody gets started with, based on the ATmega328 (SMD).
ARDUINO UNO REV3 SMD Code: A000073 The board everybody gets started with, based on the ATmega328 (SMD). The Arduino Uno SMD R3 is a microcontroller board based on the ATmega328. It has 14 digital input/output
DEV-1 HamStack Development Board
Sierra Radio Systems DEV-1 HamStack Development Board Reference Manual Version 1.0 Contents Introduction Hardware Compiler overview Program structure Code examples Sample projects For more information,
CONTENTS BIGAVR2 KEY FEATURES 4 CONNECTING THE SYSTEM 5 INTRODUCTION 6
CONTENTS BIGAVR2 KEY FEATURES 4 CONNECTING THE SYSTEM 5 INTRODUCTION 6 Switches 7 Jumpers 8 MCU Sockets 9 Power Supply 11 On-board USB 2.0 Programmer 12 Oscillator 14 LEDs 15 Reset Circuit 17 Push-buttons
MAX14850PMB1 Peripheral Module
9-633; Rev 0; 5/2 General Description The MAX4850PMB peripheral module utilizes the MAX4850 digital isolator to isolate another SPI- or UARTbased module from any host system that utilizes Pmod K - compatible
Arduino Dock 2. The Hardware
Arduino Dock 2 The Arduino Dock 2 is our supercharged version of an Arduino Uno R3 board. These two boards share the same microcontroller, the ATmel ATmega328P microcontroller (MCU), and have identical
LCMM024: DRV8825 Stepper Motor Driver Carrier,
LCMM024: DRV8825 Stepper Motor Driver Carrier, High Current The DRV8825 stepper motor driver carrier is a breakout board for TI s DRV8825 microstepping bipolar stepper motor driver. The module has a pinout
Using um-fpu64 with Arduino
Using um-fpu with Arduino Introduction This document describes how to use the um-fpu floating point coprocessor (FPU) with the Arduino open-source physical computing platform. The support routines are
ARDUINO MEGA 2560 REV3 Code: A000067
ARDUINO MEGA 2560 REV3 Code: A000067 The MEGA 2560 is designed for more complex projects. With 54 digital I/O pins, 16 analog inputs and a larger space for your sketch it is the recommended board for 3D
Features. General Description. Kit Contents. MAX32660 EV Kit Photo
MAX0 Evaluation Kit Evaluates: MAX0 General Description The MAX0 evaluation kit provides a compact development platform that provides access to all the features of the MAX0 in a tiny, easy to use board.
Evaluates: EV Kits Requiring SPI/ Parallel to USB Interface. INTF3000 Interface Board. General Description. Quick Start. Benefits and Features
INTF3000 Interface Board Evaluates: EV Kits Requiring SPI/ Parallel to USB Interface General Description The INTF3000 interface board is designed to facilitate the interfacing of Maxim s evaluation kit
SRI-02 Speech Recognition Interface
SRI-02 Speech Recognition Interface Data & Construction Booklet The Speech Recognition Interface SRI-02 allows one to use the SR-07 Speech Recognition Circuit to create speech controlled electrical devices.
General-Purpose Microcontroller Module 12a Hardware Reference Release 1.4a (October 11, 2017)
General-Purpose Microcontroller Module 12a Hardware Reference 1 General-Purpose Microcontroller Module 12a Hardware Reference Release 1.4a (October 11, 2017) Purpose: General-purpose platform to accommodate
Revision: 5/7/ E Main Suite D Pullman, WA (509) Voice and Fax. Power jack 5-9VDC. Serial Port. Parallel Port
Digilent Digilab 2 Reference Manual www.digilentinc.com Revision: 5/7/02 215 E Main Suite D Pullman, WA 99163 (509) 334 6306 Voice and Fax Overview The Digilab 2 development board (the D2) features the
MAX11205PMB1 Peripheral Module
9-60; Rev 0; / MAX0PMB Peripheral Module General Description The MAX0PMB peripheral module provides the necessary hardware to interface the MAX0 6-bit ADC to any system that utilizes PmodK-compatible expansion
ARDUINO UNO REV3 Code: A000066
ARDUINO UNO REV3 Code: A000066 The UNO is the best board to get started with electronics and coding. If this is your first experience tinkering with the platform, the UNO is the most robust board you can
Digilab 2E Reference Manual
Digilent 2E System Board Reference Manual www.digilentinc.com Revision: February 8, 2005 246 East Main Pullman, WA 99163 (509) 334 6306 Voice and Fax Digilab 2E Reference Manual Overview The Digilab 2E
Evaluates: MAX MAX31865PMB1 Peripheral Module. General Description. Features and Benefits. Peripheral Module Board Photo
General Description The MAX31865PMB1 peripheral module (Pmod ) provides the necessary hardware to interface the MAX31865 RTD-to-digital converter to any system that utilizes Pmodcompatible expansion ports
ES-562/564U COMBINATION CLOCK/TIMER
142 SIERRA ST., EL SEGUNDO, CA 90245 USA (310)322-2136 FAX (310)322-8127 www.ese-web.com ES-562/564U COMBINATION CLOCK/TIMER OPERATION AND MAINTENANCE MANUAL The ES-562U/564U is a combination six digit
PIC Dev 14 Through hole PCB Assembly and Test Lab 1
Name Lab Day Lab Time PIC Dev 14 Through hole PCB Assembly and Test Lab 1 Introduction: The Pic Dev 14 is a simple 8-bit Microchip Pic microcontroller breakout board for learning and experimenting with
An open-source hardware+software project. For design files and additional documentation, please visit:
An open-source hardware+software project. For design files and additional documentation, please visit: http://www.evilmadscientist.com/go/diavolino Support: http://www.evilmadscientist.com/forum/ Distributed
Display Real Time Clock (RTC) On LCD. Version 1.2. Aug Cytron Technologies Sdn. Bhd.
Display Real Time Clock (RTC) On LCD PR12 Version 1.2 Aug 2008 Cytron Technologies Sdn. Bhd. Information contained in this publication regarding device applications and the like is intended through suggestion
POL BMR465 Evaluation Board
User Guide POL BMR465 Evaluation Board ROA 170 64 User Guide User Guide 2 Contents 1 Introduction... 3 1.1 Prerequisites... 3 2 Reference Board ROA 170 64... 4 3 USB-PMBus adapter... 5 3.1 Connection of
LM53X Development and Evaluation Product Family
Development and Evaluation Family Revised Datasheet Version 13/MAR/2018 1.0 Overview The is the development and evaluation product family for the LM930 / LM931 Bluetooth low energy module. A great starting
Evaluation Board for AD5371 EVAL-AD5371EBZ
Preliminary Technical Data FEATURES Full-Featured Evaluation Board for the AD5371 USB Interface PC Software for Register Programming Various Reference Voltages Available Stand-Alone Operation INTRODUCTION
PCI Host Controller 14a Hardware Reference Release 1.2 (October 16, 2017)
PCI Host Controller 14a Hardware Reference 1 PCI Host Controller 14a Hardware Reference Release 1.2 (October 16, 2017) Purpose: Host Controller to support the PCI bus according to the PCI/104 specification.
Post Tenebras Lab. Written By: Post Tenebras Lab
Post Tenebras Lab PTL-ino is an Arduino comptaible board, made entirely out of through-hole components. It is a perfect project to learn how to solder and start getting into the world of micro controllers.
ARDUINO MEGA ADK REV3 Code: A000069
ARDUINO MEGA ADK REV3 Code: A000069 OVERVIEW The Arduino MEGA ADK is a microcontroller board based on the ATmega2560. It has a USB host interface to connect with Android based phones, based on the MAX3421e
CV Arpeggiator Rev 2 Build Documentation.
CV Arpeggiator Rev Build Documentation. Last updated 8-0-03 The CV Arpeggiator is a modular synth project used for creating arpeggios of control voltage. It utilizes a custom programmed PIC 6F685 micro
Mini-TNC Rev 0711 is designed exclusively to work as an APRS TNC.
Fox Delta Amateur Radio Projects & Kits Mini-TNC Technical Details and Schematic: Mini-TNC - A 1200-Baud Packet TNC Rev. 0711 Completed Mini-TNC: Mini-TNC Rev 0711 is designed exclusively to work as an
Pridgen Vermeer Robotics Xmega128 Manual
Features: 12x PWM signals with 5V supply 8x A/D Inputs with 3.3V supply 2x RS 232 Terminals 1x SPI Interface 4x 8-bit Digital IO ports 3.3V Power Bus LCD Header (4-bit mode) Smart Power Connecter Power
AVR-M Rev 5 ASSEMBLY
AVR-M Rev 5 ASSEMBLY The AVR_M is a very compact self contained Atmel AVR mcu controller board. It includes an onboard serial programmer (via PC com port), an I2C eeprom and can use a Mega163, Mega16 or
MAX3983 SMA Connector Evaluation Kit
19-3340; Rev 0, 7/04 MAX3983 SMA Connector Evaluation Kit General Description The MAX3983 SMA Connector evaluation kit (EV Kit) is an assembled demonstration board that provides electrical evaluation of
IMU Axis Gyro Evaluation Board Application Note
IMU-3000 3-Axis Gyro Evaluation Board Application Note A printed copy of this document is NOT UNDER REVISION CONTROL unless it is dated and stamped in red ink as, REVISION CONTROLLED COPY. InvenSense,
A4988 Stepper Motor Driver Carrier with Voltage Regulators
1 of 6 12/2/2011 6:37 PM A4988 Stepper Motor Driver Carrier with Voltage Regulators Pololu item #: 1183 26 in stock Price break Unit price (US$) 1 19.95 10 17.95 100 13.97 Quantity: backorders allowed
Web Site: Forums: forums.parallax.com Sales: Technical:
Web Site: www.parallax.com Forums: forums.parallax.com Sales: sales@parallax.com Technical: support@parallax.com Office: (916) 624-8333 Fax: (916) 624-8003 Sales: (888) 512-1024 Tech Support: (888) 997-8267
Bolero Nexus Emulation Adapter 208BGA 100TQ
_ V1.5 Adapters Bolero Nexus Emulation Adapter 208BGA 100TQ Ordering code IA208BGA100TQ-5607B Supported microcontrollers: Freescale MPC5605B, MPC5605BK, MPC5606BK ST equivalent devices (SPC560B54, SPC560B60)
H89-Z37 DOUBLE-DENSITY FLOPPY CONTROLLER
H8-Z37 DOUBLE DENSITY FLOPPY CONTROLLER 2015 H89-Z37 DOUBLE-DENSITY FLOPPY CONTROLLER Norberto Collado norby@koyado.com 6/6/2015 Revision History and Disclaimer Revision History Revision Date Comments
ISA Host Controller 15a Hardware Reference Release 1.2 (October 16, 2017)
ISA Host Controller 15a Hardware Reference 1 ISA Host Controller 15a Hardware Reference Release 1.2 (October 16, 2017) Purpose: Host Controller to support the ISA bus according to the PC/104 specification.
RFX 328p dev/deployment board - Assembly instructions (long version, v1.3, Feb 12, 2015)
RFX 328p dev/deployment board - Assembly instructions (long version, v1.3, Feb 12, 2015) Author: Mark Pendrith (support@embeddedcoolness.com) Kit overview The RFX 328/nRF24l01+/Proto dev board is a Arduino
um-fpu64 IDE Integrated Development Environment User Manual Release 411 Introduction Main Features Further Information Compiling
Introduction um-fpu64 IDE Integrated Development Environment User Manual Release 411 The um-fpu64 Integrated Development Environment (IDE) software provides a set of easy-to-use tools for developing applications
Board Of Education USB (#28850)
599 Menlo Drive, Suite 100 Rocklin, California 95765, USA Office: (916) 624-8333 Fax: (916) 624-8003 Sales: sales@parallax.com 1-888-512-1024 Tech Support: support@parallax.com 1-888-99-STAMP Web Site:
Bolero3M Nexus Emulation Adapter 256BGA 176TQ
_ V1.4 Adapters Bolero3M Nexus Emulation Adapter 256BGA 176TQ Ordering code IA256BGA176TQ-5646C Supported microcontrollers: Freescale MPC5644B, MPC5644C, MPC5645B, MPC5645C, MPC5646B and MPC5646C ST equivalent
Manual Main PCB Small-MIDI 4
Index PARTLIST MAIN PCB... 2 INTRODUCTION... 3 GENERAL... 3 THE CIRCUIT... 3 ASSEMBLY KIT... 4 ASSEMBLY OF THE PCB... 4 An important tip...... 4 ASSEMBLY... 4 THE CONNECTORS... 4 Power supply J1... 4 IDC
ONYX-MM-XT PC/104 Format Counter/Timer & Digital I/O Module
ONYX-MM-XT PC/104 Format Counter/Timer & Digital I/O Module User Manual V1.4 Copyright 2009 Diamond Systems Corporation 1255 Terra Bella Avenue Mountain View, CA 94043 USA Tel (650) 810-2500 Fax (650)
Maxim Integrated Products 1
9-2479; Rev 0; 6/02 MAX28 Evaluation Kit General Description The MAX28 evaluation kit (EV kit) is designed to evaluate the MAX28. The MAX28 is a 2-bit, 2-channel (six differential-channel) ADC with a 2-wire
AKKON USB CONTROLLER BOARD
TN002 AKKON USB CONTROLLER BOARD USB Microcontroller board with the PIC18F4550 * Datasheet Authors: Gerhard Burger Version: 1.0 Last update: 20.01.2006 File: Attachments: no attachments Table of versions
Sierra Radio Systems. HamStack. Project Board Reference Manual V1.0
Sierra Radio Systems HamStack Project Board Reference Manual V1.0 Welcome HamStack Project Board Reference Manual Revision 1.0.3 2011 George Zafiropoulos, KJ6VU and John Best, KJ6K This guide provides
BB-303 Manual Baseboard for TMCM-303
BB-303 Manual Baseboard for TMCM-303 Trinamic Motion Control GmbH & Co. KG Sternstraße 67 D 20357 Hamburg, Germany http://www.trinamic.com BB-303 Manual (V1.04 / Jul 9th, 2007) 2 Contents 1 Features...
Official Publication Date: 12/18/2018 Official Expiration Date: Until Next Release
Official Publication Date: 12/18/2018 Official Expiration Date: Until Next Release Revision History Version Date Comments 100 12/06/2016 Initial Release 111 6/20/2017 Updated Formatting 112 5/24/2018 Added
Breeze Board. Type A. User Manual.
Breeze Board Type A User Manual www.dizzy.co.za Contents Introduction... 3 Overview Top... 4 Overview Bottom... 5 Getting Started (Amicus Compiler)... 6 Power Circuitry... 7 USB... 8 Microcontroller...
Propeller Activity Board (#32910)
Web Site: www.parallax.com Forums: forums.parallax.com Sales: sales@parallax.com Technical: support@parallax.com Office: (916) 624-8333 Fax: (916) 624-8003 Sales: (888) 512-1024 Tech Support: (888) 997-8267
8051 Basic Development Board. Product Manual. Contents. 1) Overview 2) Features 3) Using the board 4) Troubleshooting and getting help
8051 Basic Development Board Product Manual Contents 1) Overview 2) Features 3) Using the board 4) Troubleshooting and getting help 1. Overview 2. Features The board is built on a high quality FR-4(1.6
Freeduino USB 1.0. Arduino Compatible Development Board Starter Guide. 1. Overview
Freeduino USB 1.0 Arduino Compatible Development Board Starter Guide 1. Overview 1 Arduino is an open source embedded development platform consisting of a simple development board based on Atmel s AVR
MAX44000PMB1 Peripheral Module
19-6335; Rev 0; 5/12 MAX44000PMB1 Peripheral Module General Description The MAX44000PMB1 peripheral module provides the necessary hardware to interface the MAX44000 ambient and infrared proximity sensor
ic-mhm EVAL MHM1D EVALUATION BOARD DESCRIPTION
Rev A3, Page 1/12 ORDERING INFORMATION Type Order Designation Description Evaluation board ic-mhm EVAL MHM1D ic-mhm evaluation board Ready-to-operate, includes adapter MHM3M, accessible by GUI using PC
SimPLC. User Manual.
SimPLC User Manual www.dizzy.co.za Contents Introduction... 4 Overview Top... 5 Power Circuitry... 6 Microcontroller... 7 Real-Time Calendar and Clock (RTCC)... 7 Reset Button... 7 Oscillator Socket...
USER MANUAL FOR HARDWARE REV
PI-REPEATER-2X 1. WELCOME 2. CONTENTS PAGE 1 3. GETTING STARTED There are many features built into this little board that you should be aware of as they can easily be missed when setting up the hardware
+Denotes lead-free/rohs-compliant. J5 1 J10 J13 4 J17 1 L1 1 L2 1 L4 L7 4
19-4156; Rev 0; 5/08 E V A L U A T I O N K I T A V A I L A B L E General Description The MAX3674 evaluation kit (EV kit) is a fully assembled and tested demonstration board that simplifies evaluation of
PICAXE DEVELOPMENT BOARD (AXE091)
PICAXE DEVELOPMENT BOARD (AXE0) Description: The PICAXE development board allows circuits for any size/revision of PICAXE chip ( / / / 0 / / 0) to be quickly tested using a prototyping breadboard. The
Phase Loss Protection Upgrade. Phase Loss Protection Upgrade. In this bulletin:
Phase Loss Protection Upgrade In this bulletin: Introduction... 2 Purpose... 2 General... 2 Applicability... 2 HD3070 Phase Loss Protection Upgrade Kit Parts... 2 Preparation... 4 Install the Phase Loss
INSTALL.EXE. Maxim Integrated Products 1
9-258; Rev 0; 9/02 MAX06 Evaluation Kit General Description The MAX06 evaluation kit (EV kit) is designed to evaluate the MAX06. The MAX06 is an 8-bit four-channel (two-differential-channel) ADC with a
VLSI AppNote: VSx053 Simple DSP Board
: VSx053 Simple DSP Board Description This document describes the VS1053 / VS8053 Simple DPS Board and the VSx053 Simple DSP Host Board. Schematics, layouts and pinouts of both cards are included. The