sempre Bluetooth Stereo Headset SE-BTH01 Manual Version 1.0 Copyright 2013 by sempre

Transcription

1 sempre Bluetooth Stereo Headset SE-BTH01 Manual Version 1.0 Copyright 2013 by sempre

2 Brief Introduction 1. Bluetooth wireless communication technology Bluetooth is a standard of close range radio-communication technology that was drawn up by ericsson, IBM,Intel, Nokia and Toshiba. With Bluetooth technology, we can achieve the highest transmission rate among cell phones, computers, printers, PDAs and other devices. The max transmission range of class II is 10 meters while the max transmission range of classi can reach up to 100 meters. 2. About SE-BTH01 SE-BTH01 is a stereo Bluetooth headset. It supports the following Bluetooth profiles: HSP Headset Profile HFP Hands-free Profile A2DP Advanced Audio Distribution Profile AVRCP Audio/Video Remote Control Profile You can enjoy music wireless by using the SE-BTH01 Steps as following: 1. Pairing with the Bluetooth mobile phone and PDA which support HFP. Answer and end call from the headset Redial last number Adjust the volume Switch the conversation between the headset and the mobile phone Microphone mute 2. Pairing with Bluetooth music devices and Bluetooth transmitter which support A2DP Enjoy music wirelessly Adjust the volume Remote control the function of pause/play Remote control last/next song 3. Easy to switch between conversation and music, you will not miss the incoming call during listening to music 4. Automatic connecting with the last paired device when turn on the headset - 1 -

3 Note: Even though the paired device and headset support the same Bluetooth profiles, the functions may be different due to the specification difference of the paired devices. I. before using 1. Overview 1. Retractable string 2. < key: last song 3. > key: next song 4. LED indicator 5. Multifunction button(mfb):switch on/off the headset, answer, end call, microphone mute,voice dial and voice transfer, redial last number, pause and play 6. + key:volume up/- key: volume down 7. Charging port 8. Built-in microphone 2. Charging the headset First time charging: before you use this Bluetooth headset, please charge the battery of SE-BTH01 fully. Next time: When you hear three warning tones of DONG every 20 seconds, at the same time, the red light blinks two times. It means the battery is low power and need to be charged. Charging the battery with USB cable Step1: Insert USB charging cable into USB port of PC. Step 2: Connect Charging cable with the charging port of headset. When the red light is on, the headset is charging. When the red light is off, the headset is charged fully. It takes about 3 hours to charge the headset fully. Note: Choosing travel charger or USB cable depends on different countries or areas and actual demands. Warning: The battery is recycled. Do not dispose of the battery in fire, as it may cause explosion II how to use - 2 -

4 Switching on/off headset Function Operation LED indicator Indication tone Switch on Press the MFB button for 3-5 Blue LED is on for 1 second A long DI tone seconds, and release it till the blue LED is on Switch off Press the MFB button for 3-5 seconds, and release it till the red LED is on Red LED is on for 1 second A long DI tone Note: In order to save power, the headset will automatically switch off if no devices can be connected within 5 minutes after switch on. a. Pairing the headset with Bluetooth devices How to enter pairing mode Function Operation LED indicator Indication tone Enter pairing Two DU tones mode Make sure the headset is off. Press and hold MFB button for 7-9 seconds, and release it till the red and blue blink alternately Red and blue LEDs blink alternately. Pairing the headset SE-BTH01 with Bluetooth mobile phone Please make sure your mobile phone has Bluetooth function that can be used. Specific pairing procedures may vary with different mobile phone. Please refer to your mobile phone. Manual for further information. Steps as follows: Please keep the headset and mobile phone in the range of 1 meter when pairing. Make the headset enter into pairing mode (Please refer to how to enter into pairing mode ) Start the Bluetooth function of mobile phone and search the Bluetooth devices. After searched, select SE-BTH01 in the Bluetooth device list

5 According to indication, enter password or PIN No: 0000, and press the key of yes or confirmed After successful pairing, select SE-BTH01 in the Bluetooth device list, and press connect. After successful connecting, the blue LED of the headset quickly blinks twice or three times every 4 seconds If the pairing is not successful, please switch off headset firstly, and re-pair according to step1-6 mentioned above. After Pairing is successful, paired devices will remember each other. Unless pairing information is deleted because of new pairing, no need to pair when use next time. The headset can remember 8 paired devices, when paired devices exceed 8 paired devices, the first one will be replaced. If you want to pair the headset with other devices, please pair it with the new device according to steps1-6 mentioned above. Pairing the headset with Bluetooth transmitter You can enjoy music wirelessly through connecting headset with stereo Bluetooth transmitter. Pairing steps as follows: Keep the Bluetooth transmitter and headset in the range of 1 meter when pairing. Make the headset enter into pairing mode (refer to how to enter into pairing mode).turn on the Bluetooth transmitter. It will search Bluetooth device automatically and start pairing. When the headset requests PIN No, the Bluetooth transmitter need to respond 0000 automatically. After successful pairing and connecting, the blue LED of headset quickly blinks twice every 4 seconds. The pairing password of SE-BTH01 is 0000,So, the headset can t pair with the Bluetooth transmitter which pairing password is not 0000 If the pairing is still not successful after trying several times, please refer to your Bluetooth transmitter manual carefully. Multi-pair The headset can connect with two devices at most. One is the mobile phone with HFP profile, another is the devices with A2DP profiles. If you want to finish the pairing of several Bluetooth devices, please refer to the following steps: - 4 -

6 Firstly, pair the headset with Bluetooth transmitter (refer to pairing headset with Bluetooth mobile phone ). Switch off the Bluetooth transmitter. Pair and connect the headset with the Bluetooth mobile phone( refer to pairing headset with Bluetooth mobile phone Restart Bluetooth transmitter, it will connect with headset automatically. After successful pairing with several Bluetooth devices, the paired devices will remember each other. Unless pairing information is deleted because of new pairing, otherwise make mobile phone and headset set up hands free connection next time, and re-start the Bluetooth transmitter, then the connection of several device can be performed. For the mobile phone which supports the HSP and A2DP at the same time. It my set up connection with HSP and A2DP simultaneously. At this time, start Bluetooth transmitter may not connect with the headset again. Before connecting to a Bluetooth device, please turn on the Bluetooth device s Bluetooth function. On some Bluetooth devices, take some Nokia mobile phones for example, you have to allow automatic connecting in the mobile phone s settings. Please refer to your mobile phone s manual for further information. Wearing the headset The string of this headset is retractable, please adjust according to the actual use. Logo L of the headset represents left ear, Logo R of headset represents right ear. Please wear the headset according to the indication of the Logo. Making calls with the headset SE-BTH01 Function Status of headset Operation Redial last number Standby mode Short press MFB twice quickly Volume up Conversation mode Short press or long press + key Volume down Conversation mode Short press or long press - key Answer calling Ringing Short press MFB End calling Conversation mode Short press MFB Warning: Excessive pressure from headphones can cause hearing loss

7 Not all the mobile phones support all the functions listed above. Please refer to the instruction Of your mobile phone. Some functions and indication tones may vary with different mobile phones. When the volume is adjusted to max or min, you will hear a indication tone. For some mobile phones,when you press the key of accepting on the phone, the conversation will be sent to the mobile phone. At this time, you can switch the call to headset by using the conversation switch button or throng operating on the mobile phone. Please refer to the instruction of your mobile phone or further information. Playing music When the headset connects with the mobile phone or Bluetooth transmitter which supports A2DP,you can enjoy music through headset wirelessly. Function Status of headset Operation Pause Playing music Short press MFB Play Pausing Short press MFB Last song Playing music Short press< key Next song Playing music Short press > key Volume up Playing music Short or long press + key Volume down Playing music Short or long press - key For some of mobile phones, when they are playing music, the music will transmit to the speaker of mobile phones, you have to choose transmit the sound through Bluetooth in the setting of music play interface, and then choose SE-BTH01 in the device list, the music will be transmitted to the headset the headset. Please refer to the instruction of your mobile phone for further information. When the volume of headset is adjusted to max or min, you will hear a indication tone. Remote control the function of last song/next song/pause/revert, it needs your mobile phone or Bluetooth transmitter supports AVRCP. Please refer to the instruction of your mobile phone or Bluetooth transmitter. For further information. Restoring to factory defaults and resetting Make sure the headset is off, press and hold MFB and +button simultaneously for about 8 seconds, release them when you hear two DU tones and see red LED is on, now the headset restores to factory defaults, and the pairing information will be deleted. Charge the headset to make it reset

8 LED indicator LED indicator Status of the headset Red LED is on Charging Red LED is off Finish charging Red and blue LEDs blink Pairing mode alternately Blue LED quickly blinks once Not connected to a device every 2 seconds Blue LED quickly blinks twice Set up HFP or A2DP connection every 4 seconds Blue LED quickly blinks three Set up HFP and A2DP connection times every 2 seconds Blue LED gradually turns on and Conversation mode off Red LED blinks twice every 20 Low power seconds 10) Indication tone Indication tone Status of headset Two tones every 3 seconds Conversation mode and microphone mute Three DU tones every 20 seconds Low power Pairing with computer WINDOWS or MAC If your computer has Bluetooth, you can attach your headset SE-BTH01 to it. Why thank you consult the manuals for your computer to set their association with your headset. Care and maintenance Please read the following suggestions carefully, that will help you to fulfill any warranty obligations and to enjoy this product for many years. Keep dry and don t put it in the dump place, in case of effecting the interior circuit of product. Don t put the product under the sunlight or place hot areas. High temperature will short the life of electronic device, destroy the battery, or distort certain plastic. Don t expose the product in the cold areas. It may damage the internal circuit board. Don t try to take apart the product. It may damage the product if you are not professional. Don t fall off on the floor or knock the hard substance. It may damage interior board. Don t use intensify chemical or detergent to clean the product. Don t scrap the surface with sharp things. In case the product doesn t function - 7 -

9 properly,send it to the store you bought it. The staff will help you to solve the problem. Specifications: Bluetooth Version Bluetooth profiles Effective range Working time Standby time Input Charging time Approx 2.5H Weight 103g Bluetooth V2.1+EDR Headset, hands free, A2DP,AVRCP 10 meters Music: up to 8H Talk: up to 10H Up to 250H DC:5V/130mA This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment