EcoView 8 DO Module Installation and Commissioning

Transcription

1 Document No EcoView 8 DO Module Installation and Commissioning This document covers the installation and commissioning of the EcoView 8 DO Module. See the following documents for installation of other EcoView system components: EcoView Touchscreen Installation and System Start-up ( ) EcoView Thermostat ( or ) EcoView Multi-phase Meter Installation Instructions ( ) Product Description The EcoView 8 DO Module is an eight-channel, pilotduty controller module that is used to manage lighting or other energy-consuming electrical loads that would benefit from scheduling. Relay channels may be accessed through the EcoView Touchscreen or remotely through the EcoView Web application. Product Number EcoView I/O Module, 8 DO, with Zigbee, includes power supply Caution Notations CAUTION: Equipment damage or loss of data may occur if you do not follow the procedures as specified. Required Tools and Materials Flat-blade screwdriver (1/8-inch blade width) Wire strippers Expected Installation Time 15 minutes for installing the EcoView 8 DO Module 30 minutes for wiring each DO Prerequisites NOTE: If the EcoView 8 DO Module will be directly controlling line voltage, it must be mounted in an appropriate plastic NEMA enclosure. The EcoView Touchscreen is installed and started up according to the ( ). A 120 Vac outlet is available for the EcoView 8 DO Module power supply. Depending on the type of installation, other prerequisites may have to be completed. Installation CAUTION: Always wear an electro-static discharge (ESD) wrist strap and discharge accumulated static before touching field panel components. Install the EcoView 8 DO Module near the loads to be controlled. 1. If the EcoView 8 DO Module will be directly controlling line voltage, mount the plastic NEMA enclosure in the desired location. 2. If necessary, install a standard 120 Vac outlet in the enclosure where the EcoView 8 DO Module power supply will be attached. 3. Using the provided screws, mount the EcoView 8 DO Module assembly in the enclosure. 4. Attach the EcoView 8 DO Module 24 Vac power supply to the standard 120 Vac outlet and secure with the provided plate screw. 5. Wire the individual circuits to be controlled to the 2-pin connectors for Relay 1 Relay 8. NOTE: The relays are capable of controlling loads up to 240 Vac at 3A. Anything outside of this range should be controlled by contactors. Item Number , Rev. CA Page 1 of 5

2 Figure 1: EcoView 8 DO Module Reset Button Location. Commissioning the 8 DO Module In order to commission the EcoView 8 DO Module to the ZigBee network, the DO module needs to be reset. 1. Press the recessed Reset button four times in rapid succession (see Figure 1). The NET light stops flashing. The NET light starts flashing again once it has joined the ZigBee network. 2. Press the Reset button once to send the Node ID information to the EcoView Touchscreen. Assigning the 8 DO Module to the Touchscreen 1. Press the EcoView Touchscreen CONFIG button for one second and then release it to display the Configuration screen (see Figure 6). 2. Press the DEVICE SETTINGS icon. 3. Press the Configure tab. The EcoView 8 DO Module s MAC address displays in the Unassigned Nodes list. (See Figure 6.) Assigned and unassigned EcoView 8 DO Modules, EcoView Multi-phase Meters, and EcoView Thermostats display in the Configured Device list. NOTE: Join devices one-at-a-time. This minimizes any confusion caused by having several MAC addresses displayed on the screen at one time. 4. Select a device from the Unassigned Nodes list to start the Device Configuration Wizard. Figure 2: Device Settings/Configure Tab. 5. Select the Resource Controller device driver from the list, and then press the Next button. Figure 3: Device Wizard Driver Selection. 6. If needed, select the Relay Delay parameter to edit the value, and then press the Next button. Page 2 of 5 Figure 4: Device Wizard Parameters.

3 7. Select the appropriate Zigbee MAC Address for the 8 DO Module from the list, and then press the Finish button. 8. Press the Accept button. The EcoView 8 DO Module is assigned to the EcoView Touchscreen and locked into the wireless network. 9. In the upper-left corner of the screen, press the Home button to return to the main screen. 10. Press the Exit button to save the configuration. The installation and commissioning are now complete. Figure 5: Device Wizard Zigbee MAC Selection. Figure 6: Advanced Device Configuration Screen. Troubleshooting If the EcoView 8 DO Module s MAC address is not displayed on the Device Network screen, repeat the steps in the Commissioning the 8 DO Module section. Removing Device(s) Installed to an EcoView Touchscreen in Error (Only for Sites with Multiple Touchscreens) Use this procedure if the EcoView 8 DO Module has joined the wrong EcoView Touchscreen network. 1. Remove the front bezel of the EcoView Touchscreen that the 8 DO Mdoule has joined in error. 2. Press and hold the EcoView Touchscreen CONFIG button for one second to display the Configuration screen. 3. Press the DEVICE SETTINGS icon. 4. Press the Advanced tab. 5. On the right side of the screen, press the Open button to toggle the network to closed. The button text changes to Closed. Page 3 of 5

4 6. Press the Configure tab and deselect Hide Configured Devices. 7. In the list, select the EcoView 8 DO Module. 8. In the Device Configuration Wizard, press the Decommission button. 9. Press the Accept button. 10. Return to the EcoView 8 DO Module and install it on the correct EcoView Touchscreen network. Resetting the EcoView 8 DO Module to Manufacturer s Defaults Use this procedure to reset the EcoView 8 DO Module to the manufacturer s defaults. Press and hold the recessed RESET button for more than 10 seconds and then release it. The LEDs on the EcoView 8 DO Module should cycle off, then turn on again. FCC and IC Interference Requirements This device complies with Part 15 of the FCC Rules and with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions (1) this device may not cause harmful interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. «Ce dispositif est conforme à la partie 15 des règles de FCC et aux normes permis-exemptes du Canada RSS d'industrie. L'opération est sujette aux deux conditions suivantes (1) que ce dispositif peut ne pas causer l'interférence nocive, et (2) ce dispositif doit accepter n'importe quelle interférence, y compris l'interférence qui peut causer le fonctionnement peu désiré du dispositif.» Per RSS-Gen Issue 3 (December 2010 Section 7.1.3) FCC Note This device complies with Part 15 of the FCC rules. Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment. FCC and IC Radiation Exposure Statement for Mobile Devices This equipment complies with FCC and IC radiation exposure limits set forth for an uncontrolled environment. This equipment shall be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be re-located or operating in conjunction with any other antenna or transmitter. (For compliance with FCC Code of Federal Regulations Title 47 Part ) Page 4 of 5

5 FCC Code of Federal Regulations Title 47 Part Information to the user: This equipment has been tested and found to comply with the limits for a Class B, digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turnings the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/tv technician for help. For Industry Canada User This Class B digital apparatus complies with Canadian ICES-003 Issue 4 (February 2004). «Cet appareillage numérique de la classe B est conforme ICES-003 à l'issue canadienne 4 (le février 2004).» Antenna Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. «Aux termes des règlements du Canada d'industrie, cet émetteur radioélectrique peut seulement fonctionner utilisant une antenne d'un type et (ou moins) d'un gain maximum approuvés pour l'émetteur par Industry Canada. Pour ramener des interférences radio potentielles à d'autres utilisateurs, on devrait ainsi choisir le type d'antenne et son gain que l'équivalent a isotropically rayonné la puissance (e.i.r.p.) n'est pas plus que celui nécessaire pour la communication réussie.» Information in this publication is based on current specifications. The company reserves the right to make changes in specifications and models as design improvements are introduced. EcoView is a trademark of Other product or company names mentioned herein may be the trademarks of their respective owners Building Technologies Division Retail and Commercial Systems 1000 Deerfield Parkway Buffalo Grove, IL USA For EcoView system support, please call Your feedback is important to us. If you have comments about this document, please send them to SBT_technical.editor@siemens.com Document No Printed in the USA Page 5 of 5