Ref No: Date: January 20, 1999 ELECTRICAL AND ELECTRONIC EQUIPMENT NO. 4
|
|
|
- Frederick Edwards
- 5 years ago
- Views:
Transcription
1 Ref No: Date: January 20, 1999 ELECTRICAL AND ELECTRONIC EQUIPMENT NO. 4 To: Manufacturers of Cord-Connected Equipment Subject: Publication of Technical Information Letter No. K-18 Interim Certification Requirements for Plug and Connector Configurations for Use with Cord-Connected Double-Insulated Equipment This CSA INFORMs announces the publication of Technical Information Letter (T.I.L.) No. K-18 dated January 20, Background and Rationale This Technical Information Letter (T.I.L.) is intended to clarify acceptable plug and connector configurations and the permissible number of conductors in the cord for cord-connected equipment bearing the double-insulation symbol,, for use on branch circuits rated 240 V or less in accordance with the Canadian Electrical Code, Part 1. Manufacturers have requested that CSA clarify the plug configurations that are acceptable for double-insulated equipment. Double-insulated equipment means equipment in which double insulation, or reinforced insulation, or both are used throughout and without provision for grounding. Consequently, the plugs used on cord sets and power supply cords for double-insulated equipment do not have a grounding pin. Similarly the connector will need to be of the ungrounded type. Direction This T.I.L. applies immediately to all cord-connected double-insulated equipment rated 240 V or less. These requirements are to be used in conjunction with CSA Standard CAN/CSA-C22.2 No. 0-M91, General Requirements Canadian Electrical Code, Part II. Effective Date: Immediately This Direction is applicable to products currently Certified under the following CSA product classifications: TOOLS - Portable TOOLS - Bench INDUSTRIAL CONTROL EQUIPMENT - Motor Controllers - Auxiliary Devices INDUSTRIAL CONTROL EQUIPMENT - Miscellaneous Apparatus Page 1 of 3 I:\WGM4\DOC_CTRL\INFORMs\1\mc
2 Page 2 of 3 Application and Enquires If you wish to make an application please contact one of the CSA Offices or CSA Network Partners listed below. If you require additional technical information, please contact Richard Cohen at (416) or by fax at (416) CSA Offices Telephone Telefax Montreal (514) (514) Central(Etobicoke) (416) (416) Etobicoke(Standards Sales) (416) (416) Edmonton (403) (403) Vancouver (604) (604) California (714) (714) Dallas (817) (817) Charlotte (704) (704) Nashville (615) (615) Cleveland (216) (216) Guangzhou (China) (86) (86) Shanghai (China) (86) (86) Hong Kong (852) (852) Japan (81) (81) India (080) (080) CSA Network Partners Pacific Rim (and Far East): QAS (Australia) (61) (61) CCIC (China) (86) (86) HKSTC (Hong Kong) (852) (852) BIS (India) (91) (91) JQA (Japan) (81) (81) A-PEX (Japan) (81) (81) I-TEC (Japan) (81) (81) COSMOS (Japan) (81) (81) SIRIM (Malaysia) 6 (03) (03) BVNZ (New Zealand) (64) (64) PSB (Singapore) (65) (65) KAITECH (South Korea) (82) (82) CTS (Taiwan) (886) (886) ACL (Thailand) (66) (66) I:\WGM4\DOC_CTRL\INFORMs\2\mc
3 Page 3 of 3 Europe (and Middle East): OVE (Austria) (43) (43) LCIE (France) (33) (33) UTE (France) (33) (33) N.V. KEMA (Netherlands) (31) (31) VDE (Germany) (49) (49) PCBC (Poland) (48) (48) SII (Israel) (972) (972) IMQ (Italy) (39) (39) SEMKO AB (Sweden) (46) (46) SEV (Switzerland) (41) (41) BSI (U.K.) (44) (44) BSI Testing (U.K.) (44) (44) North America: CCL (Utah) (801) (801) PSE (Florida) (813) (813) South America: BV (Brazil) (55) (55) I:\WGM4\DOC_CTRL\INFORMs\3\mc
4 TECHNICAL INFORMATION LETTER NO. K-18 Certification and Testing Division Product Group: General Date: January 20, 1999 Issued By: Richard Cohen EQUIPMENT: All Cord-Connected Equipment rated 240 V or less ITEM: Interim Certification Requirements for Cord-Connected Double-Insulated Equipment rated 240 V or less RELATED DOCUMENTS: CSA Standards: CAN/CSA-C22.2 No. 0-M91(R1997) - General Requirements-Canadian Electrical Code, Part II C22.2 No Cord Sets and Power Supply Cords C22.2 No. 42-M1984(R1996) - General Use Receptacles, Attachment Plugs and Similar Wiring Devices C22.2 No M1987(R1993) - Special Use Attachment Plugs, Receptacles and Connectors NEMA Standard: WD Wiring Devices - Dimensional Requirements Background and Rationale This T.I.L. is writtento clarify the plug and connector configurations acceptable for double-insulated equipment. By definition double-insulated equipment means equipment in which double insulation, or reinforced insulation, or both are used throughout and without provision for grounding. Consequently, the plugs used on cord sets and power supply cords for double-insulated equipment shall not have a grounding pin and the connectors shall be of the ungrounded type. 1. Scope This T.I.L. applies to cord-connected double-insulated equipment that bears the double insulation symbol,, which is intended to be connected to branch circuits rated 240 V or less in accordance with the Canadian Electrical Code, Part I. It clarifies the acceptable plug and connector configurations and the permissible number of conductors in the cord for this type of equipment. 2. Requirements 2.1 The requirements specified in Clause 2 shall be used in conjunction with CSA Standard CAN/CSA-C22.2 No. 0-M91, General Requirements Canadian Electrical Code, Part II, unless otherwise specified in a Part II Standard. Page 1 of 3 I:\WGM4\DOC_CTRL\INFORMs\4\mc
5 Page 2 of Plugs for use with cord sets and power supply cords shall comply with the requirements of the applicable CSA Part II standard. Plugs for cord-connected double-insulated equipment shall not have a grounding pin and the acceptable configurations are as follows: (a) 1-15P for 125V, 15 A or less; and (b) 2-15P for 250 V, 15A or less. See attached Figure for reference. 2.3 The maximum number of conductors permitted in the cord set or power supply cord shall be two. Cord sets and power supply cords shall comply with CSA Standard C22.2 No Connectors shall be of the ungrounded type and comply with CSA Standard C22.2 No. 42 or C22.2 No , as applicable. I:\WGM4\DOC_CTRL\INFORMs\5\mc
6 Page 3 of P, Non-Polarized Plug 1-15P, Polarized Plug 2-15P, Plug I:\WGM4\DOC_CTRL\INFORMs\6\mc
ELECTRICAL PRODUCTS NO. 2
Date: December 30, 1991 ELECTRICAL PRODUCTS NO. 2 To: Manufacturers of Electrical and Electronic Products Subject: Publication of Technical Information Letter (T.I.L.) No. K-16 Re Marking Requirements
U85026A Detector 40 to 60 GHz
Operating and Service Manual U85026A Detector 40 to 60 GHz Serial Numbers This manual applies directly to U85026A detectors with serial numbers 100 and above. For additional information on serial numbers,
World most famous and successful Conformity Assessment Scheme for mutual recognition of test certificates for electrical equipment
IECEE CB Scheme World most famous and successful Conformity Assessment Scheme for mutual recognition of test certificates for electrical equipment 9/29/2004 1 IECEE CB Scheme history IECEE CB Scheme history
Programming Note. Agilent Technologies Quick Reference Guide For the 8757D/E Scalar Network Analyzer
Programming Note Agilent Technologies Quick Reference Guide For the 8757D/E Scalar Network Analyzer Manufacturing Part Number: 08757-90130 Printed in USA Print Date: July 1992 Agilent Technologies, Inc.
Power Analyzer Firmware Update Utility Version Software Release Notes
Power Analyzer Firmware Update Utility Version 3.1.0 Software Release Notes Contents General Information... 2... 2 Supported models... 2 Minimum system requirements... 2 Installation instructions... 2
Step 1: New Portal User User ID Created Using IdentityIQ (IIQ)
Rockwell Automation PartnerNetwork Portal Single Sign-on (SSO) Login to Rockwell Automation PartnerNewtork Portal for Commercial Programs Participants Scope: This job aid provides instructions on how to
Installation Note. Removable Hard Disk Drive Upgrade Kit. For All PNA Series RF Network Analyzers. Network Analyzer Model Number
Installation Note Removable Hard Disk Drive Upgrade Kit For All PNA Series RF Network Analyzers Network Analyzer Model Number E8356A, E8357A, E8358A E8801A, E8802A, E8803A N3381A, N3382A, N3383A Upgrade
INSTALLATION INSTRUCTIONS LFH160 Cable
INSTALLATION INSTRUCTIONS LFH160 This guide describes how to connect and use the National Instruments LFH160 cable which has a maximum voltage rating of 100 VDC, CAT I. Use the LFH160 cable to connect
Keysight Technologies E3620A and E3630A Non-programmable DC Power Supplies. Data Sheet
Keysight Technologies and E3630A Non-programmable DC Power Supplies Data Sheet 02 Keysight and E3630A Non-programmable DC Power Supplies Data Sheet Reliable Power, Repeatable Results Linear power supply
NI CB-37F-LP. Introduction INSTALLATION GUIDE. Connector Block for 37-Pin D-Sub Devices
INSTALLATION GUIDE NI CB-7F-LP Connector Block for 7-Pin D-Sub Devices Introduction This installation guide describes how to install and connect signals to the NI CB-7F-LP connector block for use with
Innovative Fastening Technologies
Innovative Fastening Technologies Corporate Overview 2011 Update Infastech is one of the world s largest producers of engineered mechanical fasteners with revenues exceeding USD500 million and an industry
FP-PS-4. Features. Installation
OPERATING INSTRUCTIONS FP-PS-4 FieldPoint Power Supply These operating instructions describe the installation, features, and characteristics of the FP-PS-4. Features The FP-PS-4 is a FieldPoint power supply
Agilent 66000A 1200 W DC Modular Power System, GPIB
Agilent 66000A 1200 W DC Modular Power System, GPIB Data Sheet Speed and accuracy for test optimization 8-slot mainframe accepts up to 8 DC power modules 1200 W total DC power output, up to 150 W per module
Safety. Introduction
KickStart Guide Safety Introduction Safety precautions Before using this product, see the safety precautions associated with your instrument. The instrumentation associated with this software is intended
Global entertainment and media outlook Explore the content and tools
www.pwc.com/outlook Global entertainment and media outlook Explore the content and tools A comprehensive online source of global analysis for consumer/ end-user and advertising spending 5-year forecasts
Keysight Technologies Configuring Boundary Scan Chains on Keysight x1149 Boundary Scan Analyzer. Application Note
Keysight Technologies Configuring Boundary Scan Chains on Keysight x1149 Boundary Scan Analyzer Application Note Introduction A boundary scan chain consists of two or more boundary scan integrated circuit
OPERATING INSTRUCTIONS AND SPECIFICATIONS NI 9870E
OPERATING INSTRUCTIONS AND SPECIFICATIONS NI 9870E 4-Port, RS232 Serial Module This document describes how to use the National Instruments 9870E and includes dimensions, pin assignments, and specifications
Keysight Technologies Using Source/Measure Unit as an Ammeter
Keysight Technologies Using Source/Measure Unit as an Ammeter B2900A Precision Source/Measure Unit Demo Guide 02 Keysight Using Source/Measure Unit as an Ammeter Demo Guide Introduction The Keysight B2900A
International Business Mail Rate Card
International Business Mail Rate Card Effective from 3rd January 2017 International Business Mail International Business Mail is a service with a range of sorting and delivery options which covers Letters,
ALL-IN-ONE PRESENTATION SYSTEMS
ALL-IN-ONE PRESENTATION SYSTEMS VS-88UT VS-622DT KramerAV.com WHEN KRAMER SET OUT TO BUILD THE AV INDUSTRIES MOST VERSATILE FAMILY OF ALL-IN-ONE PRESENTATION SYSTEMS THE GOAL WAS SIMPLE, CREATE A LINE
END-OF-SALE AND END-OF-LIFE ANNOUNCEMENT FOR THE CISCO MEDIA CONVERGENCE SERVER 7845H-2400
END-OF-LIFE NOTICE, NO. 2566 END-OF-SALE AND END-OF-LIFE ANNOUNCEMENT FOR THE CISCO MEDIA CONVERGENCE SERVER 7845H-2400 Cisco Systems announces the end of life of the Cisco Media Convergence Server 7845H-2400.
OPERATING INSTRUCTIONS AND SPECIFICATIONS NI 9871E
OPERATING INSTRUCTIONS AND SPECIFICATIONS NI 9871E 4-Port, RS485/RS422 Serial Module This document describes how to use the National Instruments 9871E and includes dimensions, pin assignments, and specifications
ST20-PPI PC PARALLEL PORT TO OS-LINK INTERFACE
ST20-PPI PC PARALLEL PORT TO OS-LINK INTERFACE PRODUCT INFORMATION FEATURES Desktop mounted parallel port to differential OS-Link interface Standard 25 way D-type parallel port connection Standard 26 way
OPERATING INSTRUCTIONS AND SPECIFICATIONS. NI 9208E 16-Channel, ±20 ma, 24-Bit Analog Input Module
OPERATING INSTRUCTIONS AND SPECIFICATIONS NI 9208E 16-Channel, ±20 ma, 24-Bit Analog Input Module This document describes how to use the National Instruments 9208E and includes dimensions, pin assignments,
Vercise M8 Adapter. Directions for Use REV B
Vercise M8 Adapter Directions for Use 90903595-07 REV B CAUTION: Federal law restricts this device to sale, distribution and use by or on the order of a physician. Vercise M8 Adapter Trademarks All trademarks
Traffic Offload. Cisco 7200/Cisco 7500 APPLICATION NOTE
APPLICATION NOTE Cisco 700/Cisco 700 Traffic offload allows exchange carriers to offload their telephony traffic to a packet network from the Public Switched Telephone Network (PSTN). By doing so, carriers
Purchasing. Operations 3% Marketing 3% HR. Production 1%
Agenda Item DOC ID IAF CMC (11) 75 For Information For discussion For decision For comments to the author IAF End User Survey results (October 211) This report summarises the total responses to the IAF
USB On The Go AppNote October 5, 2014
USB On The Go AppNote 2456935.971748 October 5, 2014 INTRODUCTION USB On-The-Go (OTG) is a technology that allows a specially configured USB port to act as both a device port and a host port. A device
Items exceeding one or more of the maximum weight and dimensions of a flat. For maximum dimensions please see the service user guide.
Rate Card International Flats Effective from 2 April 2013 Pricing your mail Once you have selected the service you wish to use, calculate the price using the tables on the following pages. For more information
Agilent E363xA Series Programmable DC Power Supplies. Data Sheet
Agilent E363xA Series Programmable DC Power Supplies Data Sheet Reliable Power, Repeatable Results Single and triple output 80 W to 200 W output power Dual range output Low noise and excellent regulation
Keysight Technologies 8163B Lightwave Multimeter 8164B Lightwave Measurement System 8166B Lightwave Multichannel System.
Keysight Technologies 8163B Lightwave Multimeter 8164B Lightwave Measurement System 8166B Lightwave Multichannel System Data Sheet 02 Keysight 8163B Lightwave Multimeter, 8164B Lightwave Measurement System,
RTPA2A. TekConnect probe adapter for real-time spectrum analyzers. Tektronix high-performance probing solutions. Applications. Notice to EU customers
RTPA2A Extends the troubleshooting capabilities of Tektronix real-time spectrum analyzers with the world s best probes Troubleshoot and determine RF faults directly on circuit boards where no coaxial connection
International Packets
Rate Card International Packets Effective from 2 April 2013 Pricing your mail Once you have selected the service you wish to use, calculate the price using the tables on the following pages. For more information
Agilent E36XXA Series Non-Programmable DC Power Supplies. Data Sheet
Agilent E36XXA Series Non-Programmable DC Power Supplies Data Sheet Reliable Power, Repeatable Results Linear power supply Single, dual or triple output 10-turn voltage and current control Low noise and
CISCO IP PHONE 7970G NEW! CISCO IP PHONE 7905G AND 7912G XML
Q & A CISCO IP PHONE 7970G NEW! CISCO IP PHONE 7905G AND 7912G XML GENERAL QUESTIONS Q. What is the Cisco IP Phone 7970G? A. The 7970G is our latest state-of-the-art IP phone, which includes a large color,
Cisco CallManager 4.0-PBX Interoperability: Lucent/Avaya Definity G3 MV1.3 PBX using 6608-T1 PRI NI2 with MGCP
Application Note Cisco CallManager 4.0-PBX Interoperability: Lucent/Avaya Definity G3 MV1.3 PBX using 6608-T1 PRI NI2 with MGCP Introduction This is an application note for connectivity of Lucent/Avaya
Accessories for the Agilent B2900A Series of Precision Instruments
Accessories for the Agilent B2900A Series of Precision Instruments Agilent B2901/02/11/12A Precision Source/Measure Unit Agilent B2961/62A 6.5 digit Low Noise Power Source Catalog Table of Contents The
Supplier Responding to New Products RFP Event
This presentation contains instructions focused on the required steps needed for suppliers to respond to a RFP request made from the New Products group. For more general information on how to respond to
ChemiDoc and ChemiDoc MP Imaging Systems with Image Lab Touch Software Installation Qualification Protocol (IQ)
ChemiDoc and ChemiDoc MP Imaging Systems with Image Lab Touch Software Protocol (IQ) Catalog #17001401 and 17001402 Table of Contents Page Section 1: General Information... 3 1.1 Scope... 3 1.2 Protocol
Configuring DHCP for ShoreTel IP Phones
Configuring DHCP for ShoreTel IP Phones Network Requirements and Preparation 3 Configuring DHCP for ShoreTel IP Phones The ShoreTel server provides the latest application software and configuration information
You need the following to set up and use your terminal block:
INSTALLATION GUIDE NI TB-2706 PXI/PXIe Terminal Block for M Series and NI 6143 Devices Contents Introduction This installation guide describes how to install and connect signals to the NI TB-2706 terminal
Keysight B4655A FPGA Dynamic Probe for Xilinx. Data Sheet
Keysight B4655A FPGA Dynamic Probe for Xilinx Data Sheet 02 Keysight B4655A FPGA Dynamic Probe for Xilinx - Data Sheet The Challenge You rely on the insight a logic analyzer provides to understand the
HP Notebook QuickDock Maintenance and Service Guide
HP Notebook QuickDock Maintenance and Service Guide Copyright 2006, 2008 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warranties
The Role of SANAS in Support of South African Regulatory Objectives. Mr. Mpho Phaloane South African National Accreditation System
The Role of SANAS in Support of South African Regulatory Objectives Mr. Mpho Phaloane South African National Accreditation System Outline of Presentation INTRODUCTION STATUS OF SANAS TECHNICAL INFRASTRUCTURE
Keysight N2753A and N2754A Windows XP to Windows 7 Upgrade Kits For Infiniium 9000, 90000, and X-Series Oscilloscopes. Configuration Guide
Keysight N2753A and N2754A Windows XP to Windows 7 Upgrade Kits For Infiniium 9000, 90000, and 90000 X-Series Oscilloscopes Configuration Guide 02 Keysight N2753A and N2754A Windows XP to Windows 7 Upgrade
Keysight Technologies UXG Agile Signal Generator, Modified Version N5191A
Keysight Technologies UXG Agile Signal Generator, Modified Version N5191A Configuration Guide This configuration guide will help you determine which performance options, accessories, and services to include
N2753A and N2754A Windows XP to Windows 7 Upgrade Kits. For Infiniium 9000, 90000, and X-Series Oscilloscopes
N2753A and N2754A Windows XP to Windows 7 Upgrade Kits For Infiniium 9000, 90000, and 90000 X-Series Oscilloscopes All new Infiniium 9000, 90000, and 90000-X oscilloscopes now ship standard with Microsoft
Cisco Extensible Provisioning and Operations Manager 4.5
Data Sheet Cisco Extensible Provisioning and Operations Manager 4.5 Cisco Extensible Provisioning and Operations Manager (EPOM) is a Web-based application for real-time provisioning of the Cisco BTS 10200
IATF Stakeholder Conference
IATF Stakeholder Conference 13 September 2017 Oberursel, Germany Rüdiger Funke (BMW Group) Number of certified sites against ISO/TS 16949 (and IATF 16949) 70,000 60,000 50,000 40,000 30,000 30,156 50,071
Agilent U8000 Series Single Output DC Power Supplies. Data Sheet
Agilent U8000 Series Single Output DC Power Supplies Data Sheet Key Features Excellent load and line regulation: (CV:
Cisco Aironet In-Building Wireless Solutions International Power Compliance Chart
Cisco Aironet In-Building Wireless Solutions International Power Compliance Chart ADDITIONAL INFORMATION It is important to Cisco Systems that its resellers comply with and recognize all applicable regulations
Cisco Voice Services Provisioning Tool 2.6(1)
Data Sheet Cisco Voice Services Provisioning Tool 2.6(1) The Cisco Voice Services Provisioning Tool (VSPT) provides a GUI for the creation, modification, and execution of signaling connections, trunks,
International Business Parcels Rate card
International Business Parcels Rate card Effective from 2nd January 2018 Tracked Standard Tracked Tracked Signed Standard 1 Contents International Business Parcels services...3 International Business Tracked...4
Agilent U2941A Parametric Test Fixture
Agilent U2941A Parametric Test Fixture Data Sheet The Agilent U2941A parametric test fixture is designed to complement usage of the Agilent U2722A USB modular source measure unit in the testing of semiconductor
RT-AX95U Wireless-AX11000 Tri Band Gigabit Router
RT-AX95U Wireless-AX11000 Tri Band Gigabit Router Quick Start Guide E13976 / First Edition / February 2018 Package contents RT-AX95U Wireless Router 8 * wireless antennas AC adapter Network cable (RJ-45)
Agilent E363xA Series Programmable DC Power Supplies. Data Sheet
Agilent E363xA Series Programmable DC Power Supplies Data Sheet Reliable Power, Repeatable Results Single and triple output 80 W to 200 W output power Dual range output Low noise and excellent regulation
iclass SE multiclass SE 125kHz, 13.56MHz 125kHz, 13.56MHz
Date created: 11 July 2016 Last update: 18 August 2016 READERS REGULATORY CERTIFICATION BY COUNTRY. The following table consists of the current regulatory certifications for the readers. HID Global is
How to Debug USB 3.1 Gen 1 & Gen 2 Electrical Compliance Failures APPLICATION NOTE
How to Debug USB 3.1 Gen 1 & Gen 2 Electrical Compliance Failures 1. Introduction: The USB Type-C connector provides a smaller, thinner and more robust alternative to existing USB 3.1 connectors such as
CISCO 7304 SERIES ROUTER PORT ADAPTER CARRIER CARD
DATA SHEET CISCO 7304 SERIES ROUTER PORT ADAPTER CARRIER CARD The Cisco 7304 Router, part of the industry-leading Cisco 7000 Series, is optimized to deliver flexible, high-performance IP and Multiprotocol
Instructions. (For 6180 Industrial Computers) Installing a Processor Upgrade
Instructions (For 6180 Industrial Computers) This document describes how to remove or install a Pentium processor in the 6180 Industrial Computer. Processor specifications are also provided. Installing
Keysight Technologies
Keysight Technologies FET Characterization Using the B2900A Series of SMUs Technical Overview Introduction Keysight B2901/02/11/12A Precision Source/Measure Unit Keysight B2901A Precision SMU, 1ch, 100
Agilent Technologies Infiniium MSO8000 and MSO9000 Series N5397A FPGA Dynamic Probe for Xilinx
Agilent Technologies Infiniium MSO8000 and MSO9000 Series N5397A FPGA Dynamic Probe for Xilinx Data Sheet The challenge You rely on the insight a MSO (mixed-signal oscilloscope) provides to understand
High-Performance Differential Probes P7350 P7330 P6330 Datasheet
High-Performance Differential Probes P7350 P7330 P6330 Datasheet Applications Communications (Gigabit Ethernet, Fibre Channel, InfiniBand) Semiconductor characterization and validation PCI Express Serial
Keysight B2980A Series Femto/Picoammeter Electrometer/High Resistance Meter
Keysight B2980A Series Femto/Picoammeter Electrometer/High Resistance Meter Configuration Guide The world s only graphical Picoammeter/Electrometer that can confidently measure down to 0.01 fa and up to
DATA SHEET. Catalyst Inline Power Patch Panel
DATA SHEET Inline Power Patch DEPLOYED IN THE WIRING CLOSET, THE CATALYST INLINE POWER PATCH PANEL PROVIDES FAST ETHERNET ENHANCEMENTS NEEDED FOR MULTISERVICE NETWORKING WHILE PRESERVING CUSTOMER INVESTMENTS
Agilent E5061B Network Analyzer. Configuration Guide
Agilent E5061B Network Analyzer Configuration Guide Ordering guide The following steps will guide you through configuring your E5061B. Standard furnished item Description Installation guide CD ROM IO libraries
E-Seminar. Voice over IP. Internet Technical Solution Seminar
E-Seminar Voice over IP Internet Technical Solution Seminar Voice over IP Internet Technical Solution Seminar 3 Welcome 4 Objectives 5 Telephony in Business 6 VoIP and IP Telephony 7 Traditional Telephony
I 2 C and SPI Protocol Triggering and Decode for Infiniium 8000 and Series Oscilloscopes
I 2 C and SPI Protocol Triggering and Decode for Infiniium 8000 and 90000 Series Oscilloscopes Data sheet This application is available in the following license variations. Order N5391A for a user-installed
Troubleshooting Ethernet Problems with Your Oscilloscope APPLICATION NOTE
Troubleshooting Ethernet Problems with Your Oscilloscope Introduction Ethernet is a family of frame-based computer networking technologies for local area networks (LANs), initially developed at Xerox PARC
Keysight E5063A ENA Series Network Analyzer
Keysight E5063A ENA Series Network Analyzer 100 khz to 500 M/1.5 G/3 G/4.5 G/6.5 G/8.5 G/14 G/18 GHz Configuration Guide 02 Keysight E5063A ENA Series Network Analyzer - Configuration Guide Ordering Guide
TestJet/VTEP Hardware Description and Verification
TestJet/VTEP Hardware Description and Verification Application Note Agilent Technologies Notices Agilent Technologies, Inc. 2008 No part of this document may be reproduced in any form or by any means (including
FieldPoint. FP-1000/1001 FieldPoint Quick Start Guide. Install the Network Module Mount the module on a DIN rail. What You Need to Get Set Up
TM FieldPoint FP-1000/1001 FieldPoint Quick Start Guide What You Need to Get Set Up Network module 35 mm DIN rail Two DIN rail locks (included) Terminal base(s) I/O module(s) 11 30 VDC power supply Accessories:
One step ahead in home automation
Consumer Technology One step ahead in home automation testing and Certification services for Smart Home devices For over 120 years, UL has been advancing safety science in support of successful product
Keysight E6966B IMS-SIP Network Emulator. Technical Overview
Keysight E6966B IMS-SIP Network Emulator Technical Overview 02 Keysight E6966B IMS-SIP Network Emulator - Technical Overview Accelerate Performance Testing of Cellular User Equipment in an All-IP IMS-SIP
Single-channel Silicon ESD Protection Devices
Product Overview TE Connectivity s Silicon ESD devices help to protect electronic circuits against damage from Electrostatic Discharge (ESD), surge and cable discharge events. The Silicon ESD (SESD) devices
Fast 3D EMC/EMI Scan with Detectus Scanning System and Tektronix Real Time Spectrum Analyzers CASE STUDY
Fast 3D EMC/EMI Scan with Detectus Scanning System and Tektronix Real Time Spectrum Analyzers Fast 3D EMC/EMI Scan with Detectus Scanning System and Tektronix Real Time Spectrum Analyzers Customer Solution
Conferencing and Recording
Conferencing and Recording User Guide 03 July 2018 Contents About conferencing 3 How to schedule a meeting 4 How to join a StarLeaf meeting 6 About global telephone dial-in numbers 10 Europe, Middle East,
A 3/25/99 4:23 PM Page 23 APC Global Services 1999 Al Specificat
APC Global Services 1 Boston Edison Testimonial I now have peace of mind knowing that our facility is protected by the professionals from APC s Global Services Group and the APC Silcon DP300E. Franco Pasquale
EventBuilder.com. International Audio Conferencing Access Guide. This guide contains: :: International Toll-Free Access Dialing Instructions
EventBuilder.com International Audio Conferencing Access Guide TM This guide contains: :: International Toll-Free Access Dialing Instructions :: ATFS (Access Toll-Free Service) Dialing Instructions ::
Multi-Site Parallel Testing with the S535 Wafer Acceptance Test System APPLICATION NOTE
Multi-Site Parallel Testing with the S535 Wafer Acceptance Test System In semiconductor wafer production, minimizing the cost of test has been identified as the number one challenge. The biggest factor
Agilent E4982A LCR Meter
Agilent E4982A LCR Meter 1 MHz to 3 GHz Configuration Guide Ordering guide The following steps will guide you through configuring your E4982A. Standard furnished item Description Test head with 1m test
Agilent Technologies InfiniiVision MSO N5406A FPGA Dynamic Probe for Xilinx
Agilent Technologies InfiniiVision MSO N5406A FPGA Dynamic Probe for Xilinx Data Sheet Figure 1. FPGA dynamic probe for Xilinx used in conjunction with an Agilent InfiniiVision 6000 or 7000 Series MSO
How to Troubleshoot System Problems Using an Oscilloscope with I 2 C and SPI Decoding APPLICATION NOTE
How to Troubleshoot System Problems Using an Oscilloscope with I 2 C and SPI Decoding Introduction Most microcontroller-based designs use I 2 C or SPI or both, to communicate among controllers and between
Demo Guide. Keysight Multi-Operator with M937xA PXIe Vector Network Analyzers
Demo Guide Keysight Multi-Operator with M937xA PXIe Vector Network Analyzers Table of Contents Preparation for Demo... 3 Equipment Requirements... 3 Setup Four Operators Configuration Using 4 x 4-Ports
TBX-96 TERMINAL BLOCK
INSTALLATION GUIDE TBX-96 TERMINAL BLOCK This guide describes how to install and use the TBX-96 terminal block with the SCXI-1100, SCXI-1102B/C, SCXI-1104/C, and SCXI-1581 modules. The TBX-96 is a shielded,
Using the U8030 Series Power Supply Output Sequencing Feature
Using the U8030 Series Power Supply Output Sequencing Feature Application Note The Agilent U8030 Series Triple-Output DC Power Supply is the first tripleoutput DC power supply in its class to offer an
Agilent Technologies B4656A FPGA Dynamic Probe for Altera
Agilent Technologies B4656A FPGA Dynamic Probe for Altera Data Sheet The challenge You rely on the insight a logic analyzer provides to understand the behavior of your FPGA in the context of the surrounding
NI 653x Cable Adapter
USER GUIDE NI 65x Cable Adapter Contents The NI 65x cable adapter interfaces with National Instruments high-speed digital I/O (DIO) devices. The cable adapter provides an easy way to connect the Very High
THE POWER OF A STRONG PARTNERSHIP.
THE POWER OF A STRONG PARTNERSHIP. Now you can harness a network of resources. Connections, knowledge, and expertise. All focused on your success. The Cisco Channel Partner Program. BE CONNECTED. Great
AC/DC (120V) Input Module Cat. No IAD Series C
Installation Instructions To The Installer Pre-installation Considerations Power Requirements Initial Handling This document provides information on: important pre-installation considerations power supply
6640A Series Single-Output, 200 W DC Power Supplies, GPIB
6640A Series Single-Output, 200 W DC Power Supplies, GPIB Data Sheet Speed and accuracy for test optimization Fast, low-noise outputs Analog control of output voltage and current Fan-speed control to minimize
Tektronix Logic Analyzer Probes P5900 Series Datasheet
Tektronix Logic Analyzer Probes P5900 Series Datasheet Applications Digital hardware validation and debug Monitoring, measurement, and optimization of digital hardware performance Embedded software integration,
Keysight Technologies N6472A IEEE802.3bs/cd Compliance Application
Keysight Technologies N6472A IEEE802.3bs/cd Compliance Application For Infiniium Z-Series Oscilloscopes Data Sheet Characterize electrical pulse amplitude modulated (PAM) and Non-Return-to-Zero (NRZ) signals
LabVIEW DSP Module. Contents. Introduction RELEASE NOTES. Version 1.0
RELEASE NOTES LabVIEW DSP Module Version 1.0 Contents Introduction Introduction... 1 LabVIEW Embedded Edition... 2 System Requirements... 3 Installation... 3 DSP Module Documentation... 4 Where to Go for
NEW METHOD FOR ORDERING CISCO 1700 SERIES MODULAR ACCESS ROUTERS AND CISCO 1800 SERIES INTEGRATED SERVICES ROUTERS SOFTWARE SPARE IMAGES
PRODUCT BULLETIN, NO. 2748 NEW METHOD FOR ORDERING CISCO 1700 SERIES MODULAR ACCESS ROUTERS AND CISCO 1800 SERIES INTEGRATED SERVICES ROUTERS SOFTWARE SPARE IMAGES Until recently, every release of Cisco
Agilent B4655A FPGA Dynamic Probe for Xilinx
Agilent B4655A FPGA Dynamic Probe for Xilinx Data Sheet The Challenge You rely on the insight a logic analyzer provides to understand the behavior of your FPGA in the context of the surrounding system.
FP-2000/2010 FieldPoint Quick Start Guide
FP-2000/2010 FieldPoint Quick Start Guide What You Need to Get Set Up 1 Network Module Mounting Hardware (DIN rail or panel mount accessory) Terminal Base(s) I/O Module(s) Power Supply Accessories: Ethernet
Quick Reference Guide. Light Emitting Diode (LED) Lighting Applications
Quick Reference Guide Light Emitting Diode () Lighting Applications APPLICATIONS Power input protection from voltage and current transients Emergency lighting battery protection from overcurrent and heat
VME-GPIB Installation and User Guide
VME-GPIB Installation and User Guide Contents Introduction Introduction... 1 What Your Kit Should Contain... 2 Optional Equipment and Software Packages... 3 Unpacking your VME-GPIB... 3 Functional Overview...
NI 6521 Specifications
NI 6521 Specifications This document lists specifications for the NI 6521 device. All specifications are subject to change without notice. These specifications are typical at 25 C unless otherwise noted.