TRS5020EN-S001-W. Preliminary Technical Data (February 14 th, 2008)

Transcription

1 Preliminary Technical Data (February 14 th, 2008) TRS5020EN-S001-W 10 Gigabit/s SFP+ Transceiver All specifications described herein are subject to change without prior notice TRS5020EN-S001-W: 10GBASE-LR Transceiver in 10 Gigabit Ethernet FEATURES SFF-8431 Compliant SFI Electrical Interface Hot Z-Pluggable LC-Duplex Optical Receptacle I2C Support Uncooled 1.3μm DFB-LD PIN Photo-detector Two R Transceiver: Reamplify and Reshape Operating Case Temperature: 0 to 70 C Maximum Power Dissipation 1W under all operating conditions Compliant to pertinent IEEE 802.3ae 10GBASE-LR RoHS 6 compliant SFF-8432 Compliant Technique #2 Latch Mechanism REFERENCE The following interface standards are relevant to SFP+ Specifications. 1) SFF-8431 Enhanced 8.5 and 10 Gigabit Small Form Factor Pluggable Module (SFP+) 2) SFF Improved Pluggable Form factor 3) SFF mm SFP+ Card Edge Connector Dimensioning 4) SFF Diagnostic Monitoring Interface for Optical Xcvrs (Rev. 9.6) 5) INF-8074i - SFP (Small Form Factor) Transceiver 6) IEEE802.3ae CL 52 - IEEE Standard (10Gigabit Ethernet Clause) 7) MIL-STD-883, Method ) JESD22-A114-A (HBM) 9) IEC (Air Discharge) DESCRIPTION General Opnext s Enhanced 10Gigabit Small Form Factor Pluggable Module SFP+ TRS5020EN-S001-W is a hot pluggable transceiver module in the Z-direction that is usable in typical router line card applications, Storage, IP network and LAN and compliant to SFP+ MSA. The TRS5020EN-S001-W is a integrated 10.3Gbit/s optical transceiver module that consists of a 10.3Gbit/s optical transmitter and receiver. This version of Opnext Inc. transceiver line uses an uncooled direct modulation (DM) 1310nm DFB Laser Diode to achieve 10km over standard single mode fiber as 10GBASE-LR of the IEEE 802.3ae. Mechanical dimensions, connecters and footprint of TRS5020EN-S001-W conform to SFP+ MSA. The module size is 56.5mm L x 13.9mm W x 11.85mm H with 20-pin electrical connector. The maximum power consumption is 1.0 W and power supply voltage is +3.3 V. This document may contain technologies regulated by law [ECCN: 5E001.c.1, 5E001.c.2.d, 5E991 as of April 2005]. In the case of the export of product(s) and/or technologies described in this document, please take the appropriate procedure in conforming to all regulations related to the export.

2 PERFORMANCE SPECIFICATIONS Absolute Maximum Ratings Stresses in excess of the Absolute Maximum Ratings can cause permanent damage to the transceiver. Table 8: Absolute Maximum Ratings No. Parameter Symbol Min. Max. Unit Remarks 1 Supply Voltage V CC T V +3.3V 2 Supply Voltage V CC R V +3.3V 3 Optical Receiver Input P IMAX dbm Average 4 Operating Case Temperature Tc C Note 1 5 Storage Temperature T STR C 6 ESD SFI pins ESD1-200 V HBM 7 ESD except for SFI pins ESD2-2 kv HBM Note 1: Case temperature reference point is TBD. Operating Environment Electrical and optical characteristics below are defined under this operating environment, unless otherwise specified. Table 9: Operating Environment No. Parameter Symbol Min. Typ Max Unit Remarks 1 Supply Voltage V CC T V +3.3V 2 Supply Voltage V CC R V +3.3V 3 Operating Case Temperature T C C Note 1 Note 1: Case temperature reference point is TBD. Electrical Performance Table 10: Power Supply Characteristics No. Parameter Symbol Min. Typ. Max. Unit Remarks 1 Supply Voltage V CCT V 2 Supply Voltage V CCR V 3 Power Consumption P DS W Note 1 Note1: Over all operating conditions. 10

3 Optical Interface Characteristics Table 11 Optical Characteristics (Note1) No. Parameter Symbol Min. Typ. Max. Unit Remarks 1 Signaling speed (nominal) f D Gbit/s 2 Signal speed variation from nominal Δf D ppm 3 Center Wavelength λ C nm 4 Average launch power Po dbm 5 Optical modulation Amplitude OMA dbm Note 2 6 Off Transmit Power P off dbm Average 7 Side Mode Suppression Ratio Sr db Average 8 Extinction Ratio E r db 9 Transmitter eye mask Figure Receiver Overload P ro dbm Average 11 Receiver Sensitivity in OMA P rav dbm Informative 12 Stressed Receiver Sensitivity in OMA OMA rmin dbm Note 2 Note 1: Data Rate; NRZ at Gbit/s (10GBASE-LR), Mark Ratio 50%, PRBS=2 31-1, 1x10-12 BER Note 2: OMA=10log10[2P{(A-1)/(A+1)}], A = 10 (Er/10), P = 10 (Pf/10) 1.4 Normalized Amplitude Logic 1 Level Logic 0 Level Time (U.I.) Figure 16: Transmitter eye mask 11

4 Mechanical Comply to SFF-8432, the improved Pluggable form factor specification, with technique #2 latch. Comply to optional operational mechanical shock test in issue 2 of GR468. Optical Connector Parameter Specifications Remarks Comments LC Connector See FC-PI-4 Laser Safety This is a Class 1 Laser Product according to IEC :1993:+A1:1997+A2:2001. This product complies with 21 CFR and except for deviations pursuant to Laser Notice No. 50, dated (July 26, 2001) RoHS RoHS-6 compliant. 13

5 Mechanical Dimensions and label location Side Color code: Blue (LR) Top Side Bottom Product label Label design (Product label) 5020 S001 Assembled in Thailand T07H12345 Note) Production location: Japan(Made in Japan) or Thailand(Assembled in Thailand). Barcode is for serial number(code 128). TUV, RU(UL) logo is not applied for working sample. 14

6 Document number: OPN-DST Document Category: Technical Data Sheet Serial number OPN-DST Revision: 0.0 (February 14, 2008) Product Name: SFP+ Transceiver: TRS5020EN-S001-W USER INFORMATION Handling Precaution CAUTION: Take proper electrostatic-discharge(esd) precautions which handling these device. These devices are sensitive to ESD Laser Safety This product complies with IEC Class 1. Because of size constraints, laser safety labeling is not affixed to the module but is attached to the outside of the shipping box ORDERING INFORMATION TRS x x x - x x x x - x (1) (2) (3) (4) (5) (6) (7) Item Parameter Symbol (1) Product Name TRS5020: (2) 1310 nm direct modulation LD (uncooled) / PIN (3) transceiver for 10Gigabit Ethernet 10GBASE-LR (4) (5) application (6) Product Code EN: Gbit/s (7) (Function) (8) Hardware customized code S: Standard (9) Customer code1 0: General (10) Customer code2 0: Standard (11) Revision n: Revision number (12) Product Code (8) (9) (10)(11) (12) W: Working Sample Null: Mass Production Product Preliminary Data Sheet Disclaimer The preliminary data sheet is provided in order to finalize the product specifications. This data sheet is not applicable to products in MP. Until Opnext releases these products for general sales, Opnext reserves the right to change prices, features, functions, specifications, capabilities and release schedule. Sample Categories and Disclaimer There are 2 categories of samples. However, an executed CAS (Customer Approved Specifications) can always override conformance as defined below. Functional sample that has the suffix of -F or -Fn to the product number is a sample that is designed according to the customer s request. The purpose of this sample is to check and confirm the product feasibility. Thus the sample may be an R&D prototype or may be a modified current product. This sample may not be manufactured in qualified production lines nor using qualified parts. Basically Opnext guarantees the requested performance of BOL (Beginning Of Life). Any qualification will not be applied. Working sample that has the suffix of -W or -Wn to the product number is a sample to evaluate, confirm and finalize the product specifications. Basically Opnext guarantees the performance of BOL (Beginning Of Life). Not all qualifications may be completed. This sample may not be manufactured in qualified production lines nor be using qualified components. Until Opnext Inc. releases the products for general sales, Opnext Inc. reserves the right to change prices, features, functions, specifications, capabilities and release schedule. 21