BehringerMods.com. Instructions for modification of Behringer SRC analog inputs and outputs

Size: px
Start display at page:

Download "BehringerMods.com. Instructions for modification of Behringer SRC analog inputs and outputs"

Transcription

1 BehringerMods.com Instructions for modification of Behringer SRC analog inputs and outputs The following instructions will cover the details of fully modifying a unit with analog output and analog input upgrades. Steps that are specific to these options will be labelled and can be skipped if you did not purchase them. These modifications require a high level of assembly and skill. It is not recommended for a beginner at electronics. If you doubt your ability to complete the mods correctly, please contact BehringerMods to arrange an installation service. BehringerMods take no responsibility for damage caused to your equipment by modification.

2 Note: The input upgrade has a fixed gain level. The gain knob will only adjust the LED meter after upgrade. The modification package should come with the following parts: Analog Out Mods Populated PCB Ribbon signal cable Ground wire PCB Stands Analog Input Mods Populated PCB Ribbon signal cable Ground wire PCB Stands Ribbon Code: 1) Black = In L + 2) White = In L - 3) Grey = In R + 4) Violet = In R - 5) Blue = V- 6) Green = V+ 7) Yellow = Out L + 8) Orange = Out L - 9) Red = Out R + 10) Brown = Out R -

3 Remove the equipment cover and keep the screws in a dish. Output Upgrade PCB Input Upgrade PCB Place the upgrade PCBs in the case using the self-adhesive stands. Leave space for the ribbon cable plug to enter the PCB.

4 Connect ribbon cables to the upgrade PCBs. Cut the ribbons to length. Input PCB Ribbon should reach the furthest input XLR. NOTE: If installing input and output upgrades together, the Green and Blue wires on the input PCB ribbon need to reach the V+, V- pads on the output PCB. Output PCB ribbon should reach the furthest output XLR. Disconnect all cables and wires to the main PCB, including ground strap.

5 Remove the main PCB. Keep the screws in a dish. Output Upgrade Locate op-amps IC14, IC15 on the rear of the main PCB. Disable both op-amps by cutting the two power legs on each chip. Be carful not to damage the PCB.

6 To disable un-used op-amps the two power legs 4 and 8 (Vcc-, Vcc+) must be cut. Small circle marks the top left of the chip. Use a new sharp blade. Cut towards the chip body, not towards the PCB. Ensure a clear gap at the cut. Be carful, the PCB must not be damaged.

7 Solder the output PCB ribbon wires to the main PCB as shown. Black > Bottom R112 White > Bottom R47 Grey > Bottom R114 Violet > Bottom R113 Cut the back of pins 2 and 3 on each output XLR. Use side-cutters. Leave a clear gap.

8 Solder the wires to the output XLR pins as shown. Yellow > Out L XLR Pin 2 Orange > Out XLR Pin 3 Red > Out R XLR Pin 2 Brown > Out R XLR Pin 3

9 Solder the output PCB ribbon wires as shown. Blue is picking up -15V, Green is picking up +15V. Blue > Top C111 Green > Top C118. If you are only installing the output upgrade, proceed to fitting the analog ground wire near the end of these instructions.

10 Input Upgrade Locate IC7, IC17 and remove them completely. Use a new sharp knife. Cut towards the chip body, not towards the PCB. Cut each chip leg in turn. Support the chip body with your finger. Be carful not to damage the PCB.

11 Remove resistors R48, R49, R132, R133. Remove capacitors C70, C71. Solder input PCB ribbon as shown. Capacitor marking is on the top of the main PCB. Round pad is the positive leg, square pad is the negative leg. Black > C1 Positive Leg Violet > C5 Positive Leg Grey > C6 Positive Leg White > C21 Positive Leg

12 Solder Input PCB ribbon wires as shown. Brown > Bottom R122 Red > Bottom R115 Orange > Top R123 Yellow > Top R24

13 If you are only installing the Input upgrade, connect the Green and Blue wires as shown. If you are installing the Input and Output upgrades together, proceed below. Connect the Input PCB Green and Blue wires as shown. This will chain power from the Output PCB to the Input PCB. Green > Output PCB V+ Pad Blue > Output PCB V- Pad

14 Analog Ground Output upgrade ground. Use the supplied stranded wire to connect: Out L XLR Pin 1 > Output upgrade PCB GND pad. Input upgrade ground. Use the supplied stranded wire to connect: Input upgrade PCB GND pad > Output upgrade PCB GND pad. If you are only installing the Input Upgrade: Connect GND pad > Out L XLR Pin 1.

15 Re-connect all wires and cables. The upgrades should now be complete. Read the instructions again and check your work! Ensure there are no wire cuttings or solder in the case, the soldered wires are not touching other parts and solder has not splashed to the PCBs. Congratulations and enjoy!

MAIN PCB (The small one)

MAIN PCB (The small one) THANKS FOR CHOOSING ONE OF OUR KITS! This manual has been written taking into account the common issues that we often find people experience in our workshops. The order in which the components are placed

More information

QRPometer Assembly Manual Copyright 2012 David Cripe NM0S The 4 State QRP Group. Introduction

QRPometer Assembly Manual Copyright 2012 David Cripe NM0S The 4 State QRP Group. Introduction QRPometer Assembly Manual Copyright 2012 David Cripe NM0S The 4 State QRP Group Introduction Thank you for purchasing a QRPometer. We hope you will enjoy building it and and find it a useful addition to

More information

Button Code Kit. Assembly Instructions and User Guide. Single Button Code Entry System

Button Code Kit. Assembly Instructions and User Guide. Single Button Code Entry System Button Code Kit Single Button Code Entry System Assembly Instructions and User Guide Rev 1.0 December 2009 www.alan-parekh.com Copyright 2009 Alan Electronic Projects Inc. 1. Introduction... 4 1.1 Concept

More information

MAIN PCB (The small one with the square cut out from one side)

MAIN PCB (The small one with the square cut out from one side) THANKS FOR CHOOSING ONE OF OUR KITS! This manual has been written taking into account the common issues that we often find people experience in our workshops. The order in which the components are placed

More information

BuffaloLabs WiFi Lantern Assembly guide version 1

BuffaloLabs WiFi Lantern Assembly guide version 1 BuffaloLabs WiFi Lantern Assembly guide version 1 Needed equipment: Solder iron Solder wire Cutter Wire stripper (optional) Hot glue gun Overview of the components (not including USB cable and box panels)

More information

Schematic Diagram: R2,R3,R4,R7 are ¼ Watt; R5,R6 are 220 Ohm ½ Watt (or two 470 Ohm ¼ Watt in parallel)

Schematic Diagram: R2,R3,R4,R7 are ¼ Watt; R5,R6 are 220 Ohm ½ Watt (or two 470 Ohm ¼ Watt in parallel) Nano DDS VFO Rev_2 Assembly Manual Farrukh Zia, K2ZIA, 2016_0130 Featured in ARRL QST March 2016 Issue Nano DDS VFO is a modification of the original VFO design in Arduino Projects for Amateur Radio by

More information

solutions for teaching and learning

solutions for teaching and learning RKP18Motor Component List and Instructions PCB layout Constructed PCB Schematic Diagram RKP18Motor Project PCB Page 1 Description The RKP18Motor project PCB has been designed to use PIC microcontrollers

More information

solutions for teaching and learning

solutions for teaching and learning Circuit Construction Op-Amp Comparator Project The circuit diagram on the right is the circuit for your project, it is called an op-amp comparator circuit, it is called a comparator circuit as it compares

More information

Assembly Guide. LEDs. With these assembly instructions, you can easily build your own SWT16. All required components are included in this kit.

Assembly Guide. LEDs. With these assembly instructions, you can easily build your own SWT16. All required components are included in this kit. Assembly Guide With these assembly instructions, you can easily build your own SWT16. All required components are included in this kit. You need the following tools: soldering iron, wire cutter and solder.

More information

Universal Keying Adapter 3+

Universal Keying Adapter 3+ Universal Keying Adapter 3+ The Universal Keying Adapter Version 3+ kit will allow you to key nearly any transmitter or transceiver with a straight key, electronic keyer, computer serial or parallel port

More information

Electronics Construction Manual

Electronics Construction Manual Electronics Construction Manual MitchElectronics 2019 Version 3 04/02/2019 www.mitchelectronics.co.uk CONTENTS Introduction 3 How To Solder 4 Resistors 5 Capacitors 6 Diodes and LEDs 7 Switches 8 Transistors

More information

Connecting igaging DigiMAG Scales to the Caliper2PC Interface A step by step Guide

Connecting igaging DigiMAG Scales to the Caliper2PC Interface A step by step Guide What is an igaging DigiMAG Scale? The igaging DigiMAG are digital linear scales that are easily connectable to the Caliper2PC interface. They consist of two parts, the encoder and the readout unit. The

More information

KDS Channel DMX Controlled Servo Kit

KDS Channel DMX Controlled Servo Kit KDS00801 8-Channel DMX Controlled Servo Kit This is a DMX512-A controlled servo kit using ANSI approved RJ-45 connectors for DMX networks. Power requirements are 8-20 VDC @ 50 ma. The board features an

More information

LushOne Inca Synth Module Build Instructions

LushOne Inca Synth Module Build Instructions LushOne Inca Synth Module Build Instructions Getting started If you can build the LushOne base module then then building the Inca should be easy Remember: Accuracy and neatness is more important than speed

More information

Electronics Construction Manual

Electronics Construction Manual Electronics Construction Manual MitchElectronics 2018 Version 1 07/05/2018 www.mitchelectronics.co.uk CONTENTS Introduction 3 How To Solder 4 Resistors 5 Capacitors 6 Diodes and LEDs 7 Switches 8 Transistors

More information

1. Mount the echo and tremolo control switches under the keyboard shelf, in a position convenient for the organist.

1. Mount the echo and tremolo control switches under the keyboard shelf, in a position convenient for the organist. CONSOLE CONNECTOR KIT 8101 INSTALLATION INSTRUCTIONS FOR USE WITH: HAMMOND Organ Models A-100, D-100, RT2, RT3 LESLIE Speaker Models 122, 122RV KIT CONTENT Console Connector Assembly 047357 Echo Control

More information

Thumb Joystick Retail. Tools and parts you'll need. Things you'll want to know. How does it work? Skill Level: Beginner. by MikeGrusin March 22, 2011

Thumb Joystick Retail. Tools and parts you'll need. Things you'll want to know. How does it work? Skill Level: Beginner. by MikeGrusin March 22, 2011 Thumb Joystick Retail Skill Level: Beginner by MikeGrusin March 22, 2011 Thank you for purchasing our Thumb Joystick! Whether you're blasting aliens or driving a robot, you'll find it a very useful addition

More information

solutions for teaching and learning

solutions for teaching and learning RKOneAnalogue Component List and Instructions PCB layout Constructed PCB Schematic Diagram RKOneAnalogue Software Development PCB Page 1 Description The RKOneAnalogue software development PCB has been

More information

Phi-panel backpack assembly and keypad options Dr. John Liu 12/16/2012

Phi-panel backpack assembly and keypad options Dr. John Liu 12/16/2012 Phi-panel backpack assembly and keypad options Dr. John Liu 12/16/2012 1. Introduction:... 3 Currently available:... 3 2. Backpack assembly... 4 3. Connecting to a keypad... 6 4. Rotary encoder keypads...

More information

High Power (15W + 15W) Stereo Amplifier

High Power (15W + 15W) Stereo Amplifier High Power (15W + 15W) Stereo Amplifier Build Instructions Issue 1.0 Build Instructions Before you put any components in the board or pick up the soldering iron, just take a look at the Printed Circuit

More information

PICAXE EXPERIMENTER BOARD (AXE090)

PICAXE EXPERIMENTER BOARD (AXE090) (AXE00) Description: The PICAXE experimenter board allows circuits for any size/revision of PICAXE chip ( / / ) to be quickly tested using a prototyping breadboard. The experimenter board provides power

More information

IR TRANSMITTER BLOK PCB ASSEMBLY INSTRUCTIONS. Copyright EduTek Ltd Rev. 2

IR TRANSMITTER BLOK PCB ASSEMBLY INSTRUCTIONS. Copyright EduTek Ltd Rev. 2 IR TRANSMITTER BLOK PCB ASSEMBLY INSTRUCTIONS Copyright EduTek Ltd Rev. 2 Circuit Details The circuit is shown below with a parts list of components. Check through this list and identify each component.

More information

Strain gauge Measuring Amplifier GSV-1A8. Instruction manual GSV-1A8, GSV-1A8USB, GSV-1A16USB

Strain gauge Measuring Amplifier GSV-1A8. Instruction manual GSV-1A8, GSV-1A8USB, GSV-1A16USB Strain gauge Measuring Amplifier GSV-1A8 Instruction manual GSV-1A8, GSV-1A8USB, GSV-1A16USB GSV-1A8USB SubD1 (front side) GSV-1A8USB M12 (front side) GSV-1A16USB (rear side) GSV-1A8USB K6D (front side)

More information

Microsystems. SCI-6 Sound Card Interface Kit Version 1.09 January 2015

Microsystems. SCI-6 Sound Card Interface Kit Version 1.09 January 2015 UM Unified Microsystems SCI-6 Sound Card Interface Kit Version 1.09 January 2015 The SCI-6 interface was designed to be a low cost, high quality interface between your PC s sound card and radio transceiver.

More information

Part 2: Building the Controller Board

Part 2: Building the Controller Board v3.01, June 2018 1 Part 2: Building the Controller Board Congratulations for making it this far! The controller board uses smaller components than the wing boards, which believe it or not, means that everything

More information

Build Your Own Home Security System

Build Your Own Home Security System Build Your Own Home Security System Student Lab Guide Engineering Teaching Laboratory Name Date Lab Partner(s) NEW TERMS Electric Circuit: Electric circuits are paths for transmitting electric current,

More information

Vector 3D printer complete wire list including extruder PWA listing

Vector 3D printer complete wire list including extruder PWA listing Vector 3D printer complete wire list including extruder PWA listing Conventions Pin numbering for connectors It is normal practice in print circuit board (PCB) layout to denote pin 1 of a PCB mounted connector

More information

KAA Watt x 2 Class-D Audio Amplifier Kit

KAA Watt x 2 Class-D Audio Amplifier Kit KAA10021 50 Watt x 2 Class-D Audio Amplifier Kit This amplifier kit uses Texas Instruments TPA3116D2 stereo audio amplifier IC for driving speakers up to 50 watts @ 4 ohm per channel in stereo mode and

More information

VG-305A AC Traffic Light Controller Kit

VG-305A AC Traffic Light Controller Kit Galak Electronics Electronic kits and components Website: GalakElectronics.com Email: sales@galakelectronics.com Phone: (302) 832-1978 VG-305A AC Traffic Light Controller Kit Thank you for your purchase

More information

Advanced Strobe 1.0 Kit

Advanced Strobe 1.0 Kit Kit Instruction Manual Eastern Voltage Research, LLC December 2013, Rev 1 1 http://www.easternvoltageresearch.com Kit Introduction to the Kit Thank you for purchasing the Kit. If you are looking for a

More information

Chill Interface PCB Assembly Instructions

Chill Interface PCB Assembly Instructions ExcelValley Chill Interface PCB Waveblaster Module MIDI Interface Board Chill Limited Edition V2 Assembly Kit Standalone midi interface board for Waveblaster synthesizer modules. Suitable for most Waveblaster

More information

KDR00101 DMX Controlled Relay Kit

KDR00101 DMX Controlled Relay Kit KDR00101 DMX Controlled Relay Kit This is a DMX512-A relay kit using ANSI approved RJ-45 connectors for DMX networks. Power requirements are 12 Vdc @ 100 ma. The relay contact rating is 10 Amp @ 120 or

More information

Installation/assembly manual for DCC/Power shield

Installation/assembly manual for DCC/Power shield Installation/assembly manual for DCC/Power shield The DCC circuit consists of the following components: R1/R6 R2/R3 R4/R5 D1 C2 2 kω resistor ½ Watt (colour code Red/Black/Black/Brown/Brown) 10 kω resistor

More information

4.1 Parts and Components... IV Assembly Tips... IV Assembly Precautions... IV Required Tools, Equipment and Materials..

4.1 Parts and Components... IV Assembly Tips... IV Assembly Precautions... IV Required Tools, Equipment and Materials.. IV PERSONALITY MODULE ASSEMBLY 4.1 Parts and Components............ IV-1 4.2 Assembly Tips............... IV-1 4.3 Assembly Precautions............ IV-1 4.4 Required Tools, Equipment and Materials.. IV-1

More information

Conect 121 Upgrade. Copyright 2013 Conqueror Design and Engineering Ltd.

Conect 121 Upgrade. Copyright 2013 Conqueror Design and Engineering Ltd. All rights reserved. Any dispute about the use of this software and/or hardware or of these terms and conditions shall be resolved or arbitrated under English Law. Manuals and accompanying documentation

More information

KDR00301 DMX Controlled Relay Kit

KDR00301 DMX Controlled Relay Kit KDR00301 DMX Controlled Relay Kit This is a DMX512-A relay kit using ANSI approved RJ-45 connectors for DMX networks. Power requirements are 12 Vdc @ 200 ma. The relay contact rating is 10 Amp @ 120 or

More information

EQ573 Assembly guide. EQ573 Assembly guide Main board 1. Diodes. 2. Resistors (1) 3. Test pins. 4. Ceramic capacitors.

EQ573 Assembly guide. EQ573 Assembly guide Main board 1. Diodes. 2. Resistors (1) 3. Test pins. 4. Ceramic capacitors. EQ573 Assembly guide Safety warning The kits are main powered and use potentially lethal voltages. Under no circumstance should someone undertake the realisation of a kit unless he has full knowledge about

More information

EE 354 August 1, 2017 Assembly of the AT89C51CC03 board

EE 354 August 1, 2017 Assembly of the AT89C51CC03 board EE 354 August 1, 2017 Assembly of the AT89C51CC03 board The AT89C51CC03 board comes as a kit which you must put together. The kit has the following parts: No. ID Description 1 1.5" x 3.25" printed circuit

More information

Installation Instructions for: Channel Thermocouple Amplifier

Installation Instructions for: Channel Thermocouple Amplifier Installation Instructions for: 30-2204 4 Channel Thermocouple Amplifier The Advanced Engine Management (AEM) 4 channel thermocouple amplifier revolutionizes temperature measurements by providing laboratory

More information

Post Tenebras Lab. Written By: Post Tenebras Lab

Post Tenebras Lab. Written By: Post Tenebras Lab Post Tenebras Lab PTL-ino is an Arduino comptaible board, made entirely out of through-hole components. It is a perfect project to learn how to solder and start getting into the world of micro controllers.

More information

Electrical Interface 21MTC

Electrical Interface 21MTC Normen Europäischer Modellbahnen Electrical Interface 2MTC NEM 660 Page von 5 Recommendation Dimensions in mm Edition 20 (replacing edition 200). Purpose of Standard This standard defines a Interface which

More information

Pacific Antenna Two Tone Generator

Pacific Antenna Two Tone Generator Pacific Antenna Two Tone Generator Description Our Two Tone Generator kit provides two non-harmonic, sine wave signals for testing audio circuits Outputs of approximately 700Hz and 1900Hz and the combination

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS CONSOLE CONNECTOR KIT 7830 FOR USE WITH: LESLIE Speaker Model 130 Various single and double channel organs INSTALLATION INSTRUCTIONS KIT CONTENT Console Connector 137283 Switch Assembly, Cable Assembly,

More information

XYLOPHONE KIT ESSENTIAL INFORMATION. Version 2.0 CREATE YOUR OWN ELECTRONIC MUSICAL INTRUMENT WITH THIS

XYLOPHONE KIT ESSENTIAL INFORMATION. Version 2.0 CREATE YOUR OWN ELECTRONIC MUSICAL INTRUMENT WITH THIS ESSENTIAL INFORMATION BUILD INSTRUCTIONS CHECKING YOUR PCB & FAULT-FINDING MECHANICAL DETAILS HOW THE KIT WORKS CREATE YOUR OWN ELECTRONIC MUSICAL INTRUMENT WITH THIS XYLOPHONE KIT Version 2.0 Build Instructions

More information

DDS Unit Construction Guide of TJ6A pro

DDS Unit Construction Guide of TJ6A pro DDS Unit Construction Guide of TJ6A pro The main board, PA and the DDS function of TJ6A pro is the same with TJ6A. The different part is the DDS unit in which the S meter unit (SM unit) is add (see picture

More information

Gotharman s DIY demoon

Gotharman s DIY demoon Gotharman s DIY demoon Assembly Manual Index Introduction 3 Mainboard Connections 4 Control Panel 5 Assembling The Full Kit 6 Assembling demoon From Mainboard Only 16 Mounting DIY demoon In A Box 18 Troubleshooting

More information

RKP08 Component List and Instructions

RKP08 Component List and Instructions RKP08 Component List and Instructions PCB layout Constructed PCB RKP08 Scematic RKP08 Project PCB Page 1 Description The RKP08 project PCB has been designed to use PIC microcontrollers such as the Genie

More information

Colecovision 5v Memory Mod Installation

Colecovision 5v Memory Mod Installation Colecovision 5v Memory Mod Installation The Colecovision suffers from common failure points: the power supply, power switch, and 4116 DRAM. The power supply suffers from poor soldering, the power switch

More information

CP5176 Assembly guide. Soldering. CP5176 Assembly guide Main PCB PCB split. Document revision 2.1 Last modification : 12/11/17

CP5176 Assembly guide. Soldering. CP5176 Assembly guide Main PCB PCB split.  Document revision 2.1 Last modification : 12/11/17 CP5176 Assembly guide Safety warning The kits are main powered and use potentially lethal voltages. Under no circumstance should someone undertake the realisation of a kit unless he has full knowledge

More information

Shack Clock kit. U3S Rev 2 PCB 1. Introduction

Shack Clock kit. U3S Rev 2 PCB 1. Introduction Shack Clock kit U3S Rev 2 PCB 1. Introduction Thank you for purchasing the QRP Labs Shack Clock kit. This clock uses the Ultimate3S QRSS/WSPR kit hardware, but a different firmware version. It can be used

More information

A Backlighted LCD for your K1

A Backlighted LCD for your K1 A Backlighted LCD for your K1 (K1BKLTKIT) Tom Hammond - NØSS, July 27, 2006 Rev C Thanks to Wayne Burdick, N6KR for suggesting this implementation of backlighting the K1 display. APPLICABILITY This modification

More information

solutions for teaching and learning

solutions for teaching and learning RKAmp1 Component List and Instructions PCB layout Constructed PCB Schematic RKAmp1 Stereo Amplifier Page 1 Description The RKAmp1 stereo amplifier PCB has been designed around the 2 x 1watt stereo amplifier

More information

GSV-1A4 M12/2 M12/2. Highlights

GSV-1A4 M12/2 M12/2. Highlights GSV-1A4 M12/2 M12/2 Highlights Input sensitivity: 2mV/V; 4mV/V, 2 mv/v, 1mV/V, 0.5mV/V configurable via jumpers Output signals ±10V AND 12mA+-8mA on 15 pin Sub-D Integrated half and quarter bridge completion

More information

Arduino Panel Meter Clock. By Russ Hughes

Arduino Panel Meter Clock. By Russ Hughes Arduino Panel Meter Clock By Russ Hughes (russ@owt.com) OVERVIEW My father has been a lifelong Ham Radio Operator with a fondness for almost anything with a panel meter. After seeing the Trinket Powered

More information

BATC Kit MTK2 for MiniTiouner

BATC Kit MTK2 for MiniTiouner BATC Kit MTK2 for MiniTiouner Serit FTS4335V NIM Converter Document Change Log 2017-02-22 v1.01 First release 2017-03-01 v1.04 Minor mods Serit FTS4335V, Converter and MiniTiouner (built by G4KLB) Serit

More information

Pico Amiga ATX power adaptor install guide

Pico Amiga ATX power adaptor install guide Pico Amiga ATX power adaptor install guide Introduction The ATX power adaptor allows you to power your Amiga A500/A600/A1200 or CD32 from a modern ATX power supply. This variant of the design has a right

More information

Plasma Panel Replacement Guide DU-42PX12X

Plasma Panel Replacement Guide DU-42PX12X Plasma Panel Replacement Guide DU-42PX12X Panel Replacement: At this point, the panel has been determined to be defective and replacement is necessary. Upon receiving the replacement panel, it must be

More information

Connecting Mitutoyo Digimatic Devices to the Caliper2PC Interface A step by step Guide

Connecting Mitutoyo Digimatic Devices to the Caliper2PC Interface A step by step Guide Mitutoyo Digimatic Devices Mitutoyo is one of the world's leading manufacturers of precision measuring equipment, offering a huge range of professional products from micrometers, calipers to dial gauges.

More information

Insert the male, 90 angled, 2x10 connectors into the corresponding 2x10 sockets and put them in place, flat under the PCB. Solder.

Insert the male, 90 angled, 2x10 connectors into the corresponding 2x10 sockets and put them in place, flat under the PCB. Solder. MC624 Assembly guide Safety warning The kits are main powered and use potentially lethal voltages. Under no circumstance should someone undertake the realisation of a kit unless he has full knowledge about

More information

HW-101 QSK Modification T/R Relay Replacement

HW-101 QSK Modification T/R Relay Replacement HW-101 QSK Modification T/R Relay Replacement The HW and SB series of transceivers have two 4PDT relays which provide T/R, In this modification, these two relays are replaced by three 2PDT relays. These

More information

Megatouch FORCE Monitor Chassis Board Replacement

Megatouch FORCE Monitor Chassis Board Replacement Megatouch FORCE Monitor Chassis Board Replacement Visit the Merit Industries, Inc. Web site http://www.meritind.com merit industries, inc. PM0337-01 Rev C Table of Contents FORCE Classic Monitor Chassis

More information

Tubbutec SH-1oh1 µtune

Tubbutec SH-1oh1 µtune Tubbutec SH-1oh1 µtune Midi retrofit and feature extension for Roland SH-101 Installation Manual http://tubbutec.de 1 Contents Contents 2 1 Installation of the SH-1oh1 mod - µtune edition 3 1.1 Opening

More information

!There are two kit models. The ZCTK-120 is designed to operate with.!the pulse output is isolated from the mains line voltage. A pull-up resistor

!There are two kit models. The ZCTK-120 is designed to operate with.!the pulse output is isolated from the mains line voltage. A pull-up resistor CAUTION: Please make sure you have or have access to the skills necessary to assemble and use this product. Always secure the case with the included screws before applying electrical power to the power

More information

Strain gauge Measuring Amplifier GSV-1A8. Instruction manual GSV-1A8, GSV-1A8USB, GSV-1A16USB

Strain gauge Measuring Amplifier GSV-1A8. Instruction manual GSV-1A8, GSV-1A8USB, GSV-1A16USB Strain gauge Measuring Amplifier GSV-A8 Instruction manual GSV-A8, GSV-A8USB, GSV-A6USB GSV-A8USB SubD5 (front side) GSV-A8USB M2 (front side) GSV-A6USB (rear side) GSV-A8USB K6D (front side) Version:

More information

lumentouch SPECIFICATION SHEET Client: Project name: Order #: Type: Qty: FEATURES AND BENEFITS PACKAGE CONTENT HOW TO ORDER LTO

lumentouch SPECIFICATION SHEET Client: Project name: Order #: Type: Qty: FEATURES AND BENEFITS PACKAGE CONTENT HOW TO ORDER LTO Client: Project name: Order #: Type: Qty: FEATURES AND BENEFITS Flat wall mounted lighting controller Universal mounting plate compatible with any electrical backbox MINI-USB connection for software programming

More information

orban FIELD ENGINEERING BULLETIN Purpose: Units Affected: Replacement Kit, Orban Part # Replacing SSM2017 Op-Amps

orban FIELD ENGINEERING BULLETIN Purpose: Units Affected: Replacement Kit, Orban Part # Replacing SSM2017 Op-Amps orban FIELD ENGINEERING BULLETIN March 27, 2002 Orban Models: 2200, 6200, 6200S, 8200, 8282, 9200 Purpose: Due to the elimination of the SSM2017 by its manufacturer, Orban has had to choose a replacement

More information

USB-to-I2C. Professional Hardware User s Manual.

USB-to-I2C. Professional Hardware User s Manual. USB-to-I2C Professional Hardware User s Manual https://www.i2ctools.com/ Information provided in this document is solely for use with the USB-to-I2C Professional product from SB Solutions, Inc. SB Solutions,

More information

An ISO 9001 Company. BOP 1KW-MG FIRMWARE RETROFIT KIT

An ISO 9001 Company. BOP 1KW-MG FIRMWARE RETROFIT KIT INSTRUCTION MANUAL 1. DESCRIPTION KEPCO An ISO 9001 Company. BOP 1KW-MG FIRMWARE RETROFIT KIT BOP 1KW-MG RETROFIT KIT 219-0597 Kepco KIT 219-0597 contains the PROMs used to upgrade the firmware for BOP

More information

Assembly Instructions (8/14/2014) Your kit should contain the following items. If you find a part missing, please contact NeoLoch for a replacement.

Assembly Instructions (8/14/2014) Your kit should contain the following items. If you find a part missing, please contact NeoLoch for a replacement. NeoLoch NLT-28P-LCD-5S Assembly Instructions (8/14/2014) Your kit should contain the following items. If you find a part missing, please contact NeoLoch for a replacement. Kit contents: 1 Printed circuit

More information

Pacific Antenna Easy TR Switch Kit

Pacific Antenna Easy TR Switch Kit Pacific Antenna Easy TR Switch Kit Kit Description The Easy TR Switch is an RF sensing circuit with a double pole double throw relay that can be used to automatically switch an antenna between a separate

More information

USB-to-I2C. Ultra Hardware User s Manual.

USB-to-I2C. Ultra Hardware User s Manual. USB-to-I2C Ultra Hardware User s Manual https://www.i2ctools.com/ Information provided in this document is solely for use with the USB-to-I2C Ultra product from SB Solutions, Inc. SB Solutions, Inc. reserves

More information

Using solderless breadboards

Using solderless breadboards Page 1 of 9 Using solderless breadboards This document describes how to use the solderless breadboards available in the experimental didactic lab (LED, previously LADISPE) of Politecnico di Torino. 1 Setting

More information

DENTRON CLIPPERTON-L POWER SUPPLY MODULE v5.3 ASSEMBLY & INSTALLATION INSTRUCTIONS

DENTRON CLIPPERTON-L POWER SUPPLY MODULE v5.3 ASSEMBLY & INSTALLATION INSTRUCTIONS DENTRON CLIPPERTON-L POWER SUPPLY MODULE v5.3 ASSEMBLY & INSTALLATION INSTRUCTIONS WARNING: This upgrade is not for the faint of heart or inexperienced in amplifier theory and repairs as the voltages inside

More information

MP3 audio amplifier. Build Instructions. Issue 2.0

MP3 audio amplifier. Build Instructions. Issue 2.0 MP3 audio amplifier Build Instructions Issue 2.0 Build Instructions Before you put any components in the board or pick up the soldering iron, just take a look at the Printed Circuit Board (PCB). The components

More information

ME 3210: Mechatronics Signal Conditioning Circuit for IR Sensors March 27, 2003

ME 3210: Mechatronics Signal Conditioning Circuit for IR Sensors March 27, 2003 ME 3210: Mechatronics Signal Conditioning Circuit for IR Sensors March 27, 2003 This manual and the circuit described have been brought to you by Adam Blankespoor, Roy Merril, and the number 47. The Problem:

More information

Check that the unit has not been damaged during transport

Check that the unit has not been damaged during transport Check that the unit has not been damaged during transport Protection Against Fire 1. Maintain a minimum of 1 foot distance from any type of flame. 3. Replace fuse only with the specified type and rating.

More information

SM010, Assembly Manual PCB Version 1.0

SM010, Assembly Manual PCB Version 1.0 180 SM010, Assembly Manual MATRIXARCHATE 16 8 IO SEQUENTIAL MATRIX SIGNAL ROUTER SM010 1 2 1 2 3 4 5 3 4 5 6 7 8 9 10 11 12 6 7 8 9 10 11 12 13 14 15 16 PROGRAM A B C D E F G H f1 f2 20.000 180 SSSR Labs

More information

Advanced Lantern 1.0 Kit. Introduction to the Advanced Lantern 1.0 Kit

Advanced Lantern 1.0 Kit. Introduction to the Advanced Lantern 1.0 Kit Advanced LED Lantern 1.0 Instruction Manual Eastern Voltage Research, LLC Introduction to the Advanced Lantern 1.0 Kit Thank you for purchasing the Advanced Lantern 1.0 Kit. This kit is an advanced microprocessor

More information

Desktop housing AZ/EL Kit V1.2 for ERC-M Instructions. Instructions

Desktop housing AZ/EL Kit V1.2 for ERC-M Instructions. Instructions Instructions Desktop housing AZ/EL it V1.2 for ERC-M Instructions Congratulations for buying your Desktop housing AZ/EL for ERC-M. This document will guide you through the needed steps for assembly of

More information

Installation instructions DC Protection and Delay unit, Version 1.2 The package should contain: A piece of normal gauge yellow wire for the AC connect

Installation instructions DC Protection and Delay unit, Version 1.2 The package should contain: A piece of normal gauge yellow wire for the AC connect Installation instructions DC Protection and Delay unit, Version 1.2 How does the unit work? Delay: Basically a capacitor is charged via a resistor, when the voltage of the capacitor reach a certain level,

More information

Casio CZ. Non volatile memory modification Installation instructions version copyright 2013 Artefacts

Casio CZ.   Non volatile memory modification Installation instructions version copyright 2013 Artefacts Casio CZ Non volatile memory modification Installation instructions version 2.0 2017 www.artefacts.nl copyright 2013 Artefacts Introduction The Casio CZ-101 and CZ-1000 do not have a separate backup battery

More information

CONSOLE CONNECTOR KIT 9501 INSTALLATION INSTRUCTIONS

CONSOLE CONNECTOR KIT 9501 INSTALLATION INSTRUCTIONS CONSOLE CONNECTOR KIT 9501 INSTALLATION INSTRUCTIONS FOR USE WITH: HAMMOND Organ Models L-100, M-100 Series, M-l, M-2, M-3 LESLIE Speaker Models 760, 770, 825 KIT CONTENT Console Connector Assembly 043075

More information

NOTE: Read the instructions completely through before beginning actual installation.

NOTE: Read the instructions completely through before beginning actual installation. CONSOLE CONNECTOR KIT 7850 INSTALLATION INSTRUCTIONS FOR USE WITH: Various Two-channel Organs LESLIE Speaker Models 705, 705C, 720 KIT CONTENT Console Connector 138488 Switch Assembly, Cable Assembly,

More information

KNJN I2C bus development boards

KNJN I2C bus development boards KNJN I2C bus development boards 2005, 2006, 2007, 2008 KNJN LLC http://www.knjn.com/ Document last revision on December 5, 2008 R22 KNJN I2C bus development boards Page 1 Table of Contents 1 The I2C bus...4

More information

Model ver INSTALLATION MANUAL Rev CHD Elektroservis

Model ver INSTALLATION MANUAL Rev CHD Elektroservis Model 8-435 ver. 1.0 INSTALLATION MANUAL Rev. 2 7 2018 CHD Elektroservis Contents page 1 INTRODUCTION.................................................................. 3 1.1 MIDI INTERFACE KIT PARTS.......................................................

More information

QD V LED Tape DMX Driver

QD V LED Tape DMX Driver 4 320W output 1-16ch 24V 4x 5A HP SMD5050 60LED/M MP SMD3528 120LED/M SP SMD3528 60LED/M 60M 60M 20M 30M 60M 110-240VAC Input Voltage IP20 Ingress Protection 24V Output Voltage 4x 5A Max Output Current

More information

dual bipolar voltage controlled step sequencer DIY ASSEMBLY MANUAL v1.03

dual bipolar voltage controlled step sequencer DIY ASSEMBLY MANUAL v1.03 dual bipolar voltage controlled step sequencer DIY ASSEMBLY MANUAL v1.03 Contents Contents... 2 Introduction... 3 Part Sourcing Notes for Non Kit Builders... 3 Eurorack Kit Assembly... 4 Resistors and

More information

GL2200 MIXING CONSOLE

GL2200 MIXING CONSOLE GL2200 MIXING CONSOLE SYS-LINK EXPANDER OPTION This option connects a GL2200 console as a channel expander to a second console with just one or two interconnecting cables. Kit GL2200-SL1 = SINGLE Single

More information

SRI-02 Speech Recognition Interface

SRI-02 Speech Recognition Interface SRI-02 Speech Recognition Interface Data & Construction Booklet The Speech Recognition Interface SRI-02 allows one to use the SR-07 Speech Recognition Circuit to create speech controlled electrical devices.

More information

Parts List: Assembly Instructions:

Parts List: Assembly Instructions: My Ride SERVICE MANUAl MyRide ASSEMBLY GUIDE 1.1 ASSEMBLY INSTRUCTIONS ASSEMBLING THE MYRIDE Parts List: Heavy Plate Stabilizer Fin - Right Stabilizer Fin - Left Stabilizer Fin - Large Middle Power Cord

More information

RC Tractor Guy Controller V2.1 Assembly Guide

RC Tractor Guy Controller V2.1 Assembly Guide RC Tractor Guy Controller V. Assembly Guide Features 0 Push button inputs Dual axis thumb sticks with built-in push button Rotary encoders with built-in push button MCU Socket to suit Meduino Mega 560

More information

Connections to PAD-LA Series

Connections to PAD-LA Series Connections to PAD-LA Series 1. Control Parameters Four different methods (PAD-LA-1 through PAD-LA-4 connections) can be used to make connections to the PAD-LA series, depending on the control parameters.

More information

Connecting LEDs to the ADB I/O

Connecting LEDs to the ADB I/O Application Note AN-2 By Magnus Pettersson September 26 1996 Connecting LEDs to the I/O Introduction The following notes are for those of you who are a bit inexperienced with hardware components. This

More information

DMX CONTROLLED RELAY K8072

DMX CONTROLLED RELAY K8072 Total solder points: 167 Difficulty level: beginner 1 2 3 4 5 advanced DMX CONTROLLED RELAY K8072 f the means o ol. y b y la a re 2 protoc Control DMX51 wn well-kno ILLUSTRATED ASSEMBLY MANUAL Total solder

More information

PICAXE CONNECT (AXE210)

PICAXE CONNECT (AXE210) PICAXE CONNECT (AXE10) Description: The AXE10 Connect board has been designed as a experimental project board for users wishing to learn how to interface a PICAXE chip to the Maxstream module or a LocSense

More information

Installation Guide. Version: 6.1 (Digitax 4G) July 2018

Installation Guide. Version: 6.1 (Digitax 4G) July 2018 Installation Guide Version: 6.1 (Digitax 4G) July 2018 STEP SUMMARY PAGE 1 Fit Mounting Bracket and Antenna 5 2 Connect Primary Loom to Vehicle 5 3 Connect Secondary Loom to Vehicle 8 4 Connect Screen

More information

Phase Loss Protection Upgrade. Phase Loss Protection Upgrade. In this bulletin:

Phase Loss Protection Upgrade. Phase Loss Protection Upgrade. In this bulletin: Phase Loss Protection Upgrade In this bulletin: Introduction... 2 Purpose... 2 General... 2 Applicability... 2 HD3070 Phase Loss Protection Upgrade Kit Parts... 2 Preparation... 4 Install the Phase Loss

More information

Assembling the Printed Circuit Board for the EDE1200 Robot

Assembling the Printed Circuit Board for the EDE1200 Robot This board receives instructions from either a CBL2, a LabPro or (with an adapter cable) an original CBL. The board has two 595 shift registers (each providing 8 bits of on-board memory) and two EDE1200

More information

Power connections 3) Power from 2024 to Control box (The valve harness connected) Ground (0V) +24 V. The voltage between pins 1 & 2 in JPT# 123

Power connections 3) Power from 2024 to Control box (The valve harness connected) Ground (0V) +24 V. The voltage between pins 1 & 2 in JPT# 123 Power connections 3) Power from 2024 to Control box (The valve harness connected) The voltage between pins 1 & 2 in JPT# 123 connector should be +24V. 4) Power from 2024 to Control box The voltage between

More information

IQ32 Upgrade Kit Assembly Instructions

IQ32 Upgrade Kit Assembly Instructions IQ32 Upgrade Kit Assembly Instructions Jim Veatch WA2EUJ September 17, 2018 TABLE OF CONTENTS 1. INTRODUCTION... 3 2. IQ-32 UPGRADE KIT INVENTORY... 4 3. PREPARING THE RS-HFIQ AND SIDE PANELS... 6 4. CONNECTING

More information