- Delays stable and precise - 14-pin DIP package - Leads - thru-hole, J, Gull Wing or Tucked - Available in delays from 15 to 1000ns
|
|
|
- Patrick Atkins
- 5 years ago
- Views:
Transcription
1 Very Low Profile CMOS Compatible Thinny DIP Logic Delay Module Surface Mount CMOS Compatible Wee DIP Logic Delay Module Low Profile ECL Compatible Logic Delay Module Very Low Profile ECL-100k Compatible Logic Delay Module Space Saver LVQ 3V Logic Delay Modules - Delays stable and precise - 14-pin DIP package - Leads - thru-hole, J, Gull Wing or Tucked - Available in delays from 15 to 1000ns - Fast rise time on all outputs DESIGN NOTES The "DIP Series" Logic Delay Modules developed by Engineered Components Company have been designed to provide precise tapped delays with required driving
2 and pick-off circuitry contained in a single 14-pin DIP package compatible with FAST utilizing the proven technologies of active integrated circuitry and of passive networks utilizing capacitive, inductive and resistive elements. The MTBF on these modules, excess of 2 million hours. Module design includes compensation for propagation delays and incorporates internal termination at the output; no additional external components are needed to obtain the desired delay. The FXLDM-TTL is offered in 27 delays from 15 to 1000ns with each module incorporating total output and nine (9) taps. Delay tolerances are maintained as shown in the accompanying part number table, when tested under the "Test Conditions" shown. Delay time is measured at the +1.5V level on the leading edge. Rise time for all modules is 4ns maximum when measured from 0.8V to 2.0V. Temperature coefficient These modules accept either logic "1" or logic "0" inputs and reproduce the logic at the output without inversion. The delay modules are intended primarily for use with positive going pulses and are calibrated to the tolerances shown in the table on rising edge delay; where best accuracy is desired in applications using falling edge timing, it is recommended that a special unit be calibrated for the specific application. Each 10 loads on any one tap. These "DIP Series" modules are packaged in a 14-pin DIP housing, molded of flame-proof Diallyl Phthalate per MIL-M-14, Type SDG-F, and are fully encapsulated in epoxy resin. Thru-hole, J, Gull Wing or Tucked Lead configurations are available on these modules (see Part Number Table note to specify). Leads meet the solderability requirements of MIL-STD-202, Method 208. Corner standoffs on the housing of the thru-hole lead version and lead design of the surface mount versions provide positive standoff from the printed circuit board to permit solder-fillet formation and flush cleaning of solder-flux residues for improved reliability. identification and date code of manufacture. All marking is applied by silk screen process using white epoxy paint in accordance with MIL-STD-130, to meet the permanency of identification required by MIL-STD-202, Method 215.
3
4 TEST CONDITIONS 2. Vcc supply voltage is maintained at 5.0V DC. 3. All units are tested using a Schottky toggle-type positive input pulse and one Schottky load at the output being tested. 4. Input pulse width used is 5 to 10ns longer than delay of module under test; spacing between pulses (falling edge to rising edge) is three times the pulse width used. OPERATING SPECIFICATIONS *Vcc supply voltage: to 5.25V DC Vcc supply current: Constant "0" in... 45mA typical Constant "1" in... 15mA typical Logic 1 Input: Voltage... 2V min.; Vcc max. Current V = 20uA max. 5.5V = 1mA max. Logic 0 Input: Voltage V max. Current mA max. Logic 1 Voltage out: V min. Logic 0 Voltage out: V max. *Delays increase or decrease approximately 2% for a respective increase or decrease of 5% in supply voltage.
5 PART NUMBER TABLE *Suffix Part Number with G (for Gull Wing Lead), J (for J Lead), F (for Thru-hole Lead) or T (for Tucked Lead). Examples: FXLDM-TTL-50G (Gull Wing), FXLDM-TTL-70J (J Lead), FXLDM-TTL-80F (Thru-hole Lead) or FXLDM-TTL-90T (Tucked Lead). DELAYS AND TOLERANCES (in ns) PART NUMBER TAP1 TAP2 TAP3 TAP4 TAP5 TAP6 TAP7 TAP8 TAP9 OUTPUT FXLDM-TTL-15 FXLDM-TTL-19.5 FXLDM-TTL-24 FXLDM-TTL-28.5 FXLDM-TTL-33 FXLDM-TTL-42 FXLDM-TTL-50 FXLDM-TTL-60 FXLDM-TTL-70 FXLDM-TTL-80 FXLDM-TTL-90 FXLDM-TTL-100 FXLDM-TTL-125 FXLDM-TTL-150 FXLDM-TTL-175 FXLDM-TTL-200 FXLDM-TTL-250 FXLDM-TTL-300 FXLDM-TTL-350 FXLDM-TTL-400 FXLDM-TTL-450 FXLDM-TTL-500 FXLDM-TTL-600 FXLDM-TTL-700 FXLDM-TTL-800 FXLDM-TTL-900 FXLDM-TTL-1000 All modules can be operated with a minimum input pulse width of 20% of full delay or 5ns min and pulse period approaching square wave; since delay accuracies may be somewhat degraded, it is suggested that the module be evaluated under the intended specific operating conditions. Special modules can be readily manufactured to improve accuracies and/or provide customer specified random delay times for specific applications. Catalog No. C/ The Company Products Search Contact Us Sitemap Home Adobe / PDF Designed and Hosted by Ernest & Allen, Inc.
6
CZRB5338B-HF Thru. CZRB5388B-HF Voltage: 5.1V to 200V Power: 5 W RoHS Device Halogen Free
CZRB5338B-HF Thru. CZRB5388B-HF Voltage: 5.1V to 200V Power: 5 W RoHS Device Halogen Free Features - Glass passivated chip - Low leakage - Built-in strain relief - Low inductance - High peak reverse power
ACZRC5340B-G Thru. ACZRC5388B-G Voltage: 6.0 to 200 Volts Power: 5 Watts RoHS Device
CZRC5340B-G Thru. CZRC5388B-G Voltage: 6.0 to 200 Volts Power: 5 Watts RoHS Device Features - Glass passivated chip. - Low leakage. - Built-in strain relief. - Low inductance. - High peak reverse power
DS1225Y 64k Nonvolatile SRAM
19-5603; Rev 10/10 NOT RECOMMENDED FOR NEW DESIGNS 64k Nonvolatile SRAM www.maxim-ic.com FEATURES 10 years minimum data retention in the absence of external power Data is automatically protected during
TORX176 TORX176 FIBER OPTIC RECEIVING MODULE FOR DIGITAL AUDIO EQUIPMENT. 1. Maximum Ratings (Ta = 25 C) 2. Recommended Operating Conditions
FIBER OPTIC RECEIVING MODULE TORX176 FIBER OPTIC RECEIVING MODULE FOR DIGITAL AUDIO EQUIPMENT Unit: mm Conform to JEITA Standard CP 1201 (For Digital Audio Interfaces including Fiber Optic inter connections).
FIBER OPTIC TRANSMITTING MODULE TOTX147(F,T)
FIBER OPTIC TRANSMITTING MODULE TOTX147(F,T) FIBER OPTIC TRANSMITTING MODULE FOR DIGITAL AUDIO EQUIPMENT Unit: mm Conforms to JEITA Standard CP 1212 (Digital Audio Optical Interface for Consumer Equipment).
Sensing and Control the Interactive Catalog.
Interactive Catalog Supplements Catalog PDFs If you need detailed product information, or help choosing the right product for your application, see our Interactive Catalog Use the Interactive Catalog to
DS1249Y/AB 2048k Nonvolatile SRAM
19-5631; Rev 11/10 www.maxim-ic.com FEATURES 10 years minimum data retention in the absence of external power Data is automatically protected during power loss Unlimited write cycles Low-power CMOS operation
DS1258Y/AB 128k x 16 Nonvolatile SRAM
www.maxim-ic.com FEATURES 10-Year Minimum Data Retention in the Absence of External Power Data is Automatically Protected During a Power Loss Separate Upper Byte and Lower Byte Chip- Select Inputs Unlimited
E SERIES ISOLATED, PROPORTIONAL DC TO HV DC CONVERTERS
Proven Reliability E SERIES ISOLATED, PROPORTIONAL DC TO HV DC CONVERTERS 200V to 7kV at 3W / 8kV at 2W PRODUCT SELECTION TABLE Output Voltage (%) 140t 120 100 80 60 40 PRODUCT DESCRIPTION The E Series
G SERIES ISOLATED, PROPORTIONAL DC TO HV DC CONVERTERS
0 Proven Reliability G SERIES ISOLATED, PROPORTIONAL DC TO HV DC CONVERTERS 100V to 6kV at 1.5W PRODUCT SELECTION TABLE NOW UL RECOGNIZED % Of Full Output 100 90 80 70 60 50 40 30 20 10 PRODUCT DESCRIPTION
TORX177(F,T) TORX177(F,T) TENTATIVE FIBER OPTIC RECEIVING MODULE FOR DIGITAL AUDIO INTERFACE. 1. Maximum Ratings (Ta = 25 C)
TENTATIVE FIBER OPTIC RECEIVING MODULE TORX177(F,T) FIBER OPTIC RECEIVING MODULE FOR DIGITAL AUDIO INTERFACE Unit: mm For JEITA Standard CP- 1212 (Digital Audio Optical Interface for Consumer Equipment).
DS1265Y/AB 8M Nonvolatile SRAM
19-5616; Rev 11/10 www.maxim-ic.com 8M Nonvolatile SRAM FEATURES 10 years minimum data retention in the absence of external power Data is automatically protected during power loss Unlimited write cycles
SCA620-EF1V1B SINGLE AXIS ACCELEROMETER WITH ANALOG INTERFACE
Datasheet SCA620-EF1V1B SINGLE AXIS ACCELEROMETER WITH ANALOG INTERFACE The SCA620 accelerometer consists of a silicon bulk micro machined sensing element chip and a signal conditioning ASIC. The chips
Rev. No. History Issue Date Remark
Preliminary 512K X 8 OTP CMOS EPROM Document Title 512K X 8 OTP CMOS EPROM Revision History Rev. No. History Issue Date Remark 0.0 Initial issue June 17, 1998 Preliminary 1.0 Change CE from VIL to VIH
DS1216 SmartWatch RAM DS1216B/C/D/H SmartWatch ROM DS1216E/F
www.maxim-ic.com FEATURES Keeps track of hundredths of seconds, seconds, minutes, hours, days, date of the month, months, and years Converts standard 2k x 8 up to 512k x 8 CMOS static RAMs into nonvolatile
Description. Kingbright
8mm (0.32INCH) SINGLE DIGIT NUMERIC DIS- PLAY Part Number: SC32-11GWA Green Features 0.32 inch digit height. Low current operation. Excellent character appearance. High light output. Easy mounting on P.C.
PAGE 1/6 ISSUE SERIES Micro-SPDT PART NUMBER R516 X3X 10X R 516 _ 1 0 _
PAGE 1/6 ISSUE 13-08-18 SERIES Micro-SPDT PART NUMBER R516 X3X 10X R516 series: the RAMSES concept merges with the SLIM LINE technology, breaking up the frequency limits of SMT switches : - FULL SMT TECHNOLOGY
TORX147(F,T) TORX147(F,T) FIBER OPTIC RECEIVING MODULE FOR DIGITAL AUDIO INTERFACE. 1. Absolute Maximum Ratings (Ta = 25 C) 2.
FIBER OPTIC RECEIVING MODULE TORX147(F,T) FIBER OPTIC RECEIVING MODULE FOR DIGITAL AUDIO INTERFACE Unit: mm For JEITA Standard CP 1212 (Digital Audio Optical Interface for Consumer Equipment). A self tapping
Description. Kingbright
10.2mm (0.4INCH) THREE DIGIT NUMERIC DISPLAY Part Number: BC04-11SEKWA Super Bright Orange Features 0.4 inch digit height. Low current operation. Excellent character appearance. Easy mounting on P.C. boards
DS1220AB/AD 16k Nonvolatile SRAM
DS122AB/AD 16k Nonvolatile SRAM www.dalsemi.com FEATURES years minimum data retention in the absence of external power Data is automatically protected during power loss Directly replaces 2k x 8 volatile
DS1210 Nonvolatile Controller Chip
Nonvolatile Controller Chip www.dalsemi.com FEATURES Converts CMOS RAMs into nonvolatile memories Unconditionally write protects when V CC is out of tolerance Automatically switches to battery when power-fail
Agilent 87222C/D/E Coaxial Transfer Switches dc to 26.5, 40, 50 GHz Product Overview
Agilent 87222C/D/E Coaxial Transfer Switches dc to 26.5, 0, 50 GHz Product Overview High performance transfer switches for microwave and RF instrumentation and systems Exceptional repeatability for more
RTE02 and RTE03 Miniature Rotary Switches
RTE02 and RTE03 Miniature Rotary Switches RTE02 and RTE03 are two types of a subminiature rotary changeover switch to be mounted on PC boards. PC pins are in a 2.54 mm (0.100) grid. RTE02 with 2 positions
sks-15/cd Extract from our online catalogue: Current to:
Extract from our online catalogue: sks-15/cd Current to: 2018-09-13 microsonic GmbH / Phoenixseestraße 7 / 44263 Dortmund / Germany / T +49 231 975151-0 / F +49 231 975151-51 / E info@microsonic.de microsonic
CAT22C Bit Nonvolatile CMOS Static RAM
256-Bit Nonvolatile CMOS Static RAM FEATURES Single 5V Supply Fast RAM Access Times: 200ns 300ns Infinite E 2 PROM to RAM Recall CMOS and TTL Compatible I/O Power Up/Down Protection 100,000 Program/Erase
LCA127LSTR. Single-Pole, Normally Open OptoMOS Relay INTEGRATED CIRCUITS DIVISION
Single-Pole, Normally Open OptoMOS Relay Parameter Ratings Units Blocking Voltage 2 V P Load Current 7 ma rms / ma DC On-Resistance (max Features Current Limiting 37V rms Input/Output Isolation Low Drive
DS WIRE INTERFACE 11 DECOUPLING CAP GND
Rev ; 4/3 Hex Nonvolatile Potentiometer with General Description The contains six 256-position nonvolatile (NV) potentiometers, 64 bytes of NV user EEPROM memory, and four programmable NV I/O pins. The
SUBMINIATURE SOLID STATE LAMP. Features. Descriptions. Package Dimensions
SUBMINIATURE SOLID STATE LAMP Part Number: AM2520SRC03 Super Bright Red ATTENTION OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Features Subminiature package. Gull wing lead.
A23W8308. Document Title 262,144 X 8 BIT CMOS MASK ROM. Revision History. Rev. No. History Issue Date Remark
Preliminary 262,144 X 8 BIT CMOS MASK ROM Document Title 262,144 X 8 BIT CMOS MASK ROM Revision History Rev. No. History Issue Date Remark 0.0 Initial issue November 11, 1999 Preliminary PRELIMINARY (November,
5.0mm x 5.0mm SURFACE MOUNT LED LAMP. Features. Descriptions. Package Dimensions
5.0mm x 5.0mm SURFACE MOUNT LED LAMP Part Number: AAAF5051XQR412ZXS-N1 Features ATTENTION OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Suitable for all SMT assembly and solder
DS1216B. SmartWatch/RAM 16K/64K FEATURES PIN ASSIGNMENT PIN DESCRIPTION
DS1216B SmartWatch/RAM 16K/64K FEATURES Keeps track of hundredths of seconds, seconds, minutes, hours, days, date of the month, months, and years Converts standard 2K x 8 and 8K x 8 CMOS static RAMs into
Model 3750 Multifunction I/O Card
Keithley Instruments, Inc. 28775 Aurora Road Cleveland, Ohio 44139 1-888-KEITHLEY www.keithley.com Model 3750 Multifunction I/O Card Connection Instructions and Specifications Introduction This instruction
DS1233A 3.3V EconoReset
3.3V EconoReset www.maxim-ic.com FEATURES Automatically restarts microprocessor after power failure Monitors pushbutton for external override Internal circuitry debounces pushbutton switch Maintains reset
DS1232 MicroMonitor Chip
DS1232 MicroMonitor Chip www.maxim-ic.com FEATURES Halts and restarts an out-of-control microprocessor Holds microprocessor in check during power transients Automatically restarts microprocessor after
E SERIES ISOLATED, PROPORTIONAL DC TO HV DC CONVERTERS
Proven Reliability ISOLATED, PROPORTIONAL DC TO HV DC CONVERTERS 2V to 7kV at 3W / 8kV at 2W PRODUCT SELECTION TABLE Output Voltage (%) 14t 12 1 8 6 4 PRODUCT DESCRIPTION The E Series is a broad line of
HIGHLY SENSITIVE 1500 V FCC SURGE BREAKDOWN VOLTAGE MINIATURE RELAY
HIGHLY SENSITIVE 15 V FCC SURGE BREAKDOWN VOLTAGE MINIATURE RELAY DS RELAYS FEATURES 1. Breakthrough height of 9.8 mm.386 inch beats the 1 mm.394 inch limit 1c, 2c, and 4c all have the same height (9.8
SPEC NO: DSAH3956 REV NO: V.7 DATE: NOV/26/2008 PAGE: 1 OF 6 APPROVED: WYNEC CHECKED:
3.5x2.8 mm SMD CHIP LED LAMP PRELIMINARY SPEC Part Number: AA3529SES/L Hyper Orange Features Single color. Suitable for all SMT assembly and solder process. Available on tape and reel. Ideal for backlighting.
HIGHLY SENSITIVE 1500 V FCC SURGE BREAKDOWN VOLTAGE MINIATURE RELAY
HIGHLY SENSITIVE 1500 V FCC SURGE BREAKDOWN VOLTAGE MINIATURE RELAY DS RELAYS RoHS Directive compatibility information http://www.mew.co.jp/ac/e/environment/ FEATURES 1. Breakthrough height of 9.8 mm.386
DS1834/A/D Dual EconoReset with Pushbutton
Dual EconoReset with Pushbutton www.dalsemi.com FEATURES 5V power-on reset 3.3V power-on reset Internal power is drawn from higher of either the input or the 3.3V IN input Excellent for systems designed
DS1810 5V EconoReset with Push-Pull Output
5V EconoReset with Push-Pull Output www.maxim-ic.com FEATURES Automatically restarts a microprocessor after power failure Maintains reset for 150 ms after V CC returns to an in-tolerance condition Reduces
500 W, Bidirectional Low Capacitance TVS Array
Available 500 W, Bidirectional Low Capacitance TVS Array DESCRIPTION This Transient Voltage Suppressor (TVS) is assembled in a QFN-143 package which has the same pinout and footprint as the SOT-143 package.
DS1646/DS1646P Nonvolatile Timekeeping RAM
19-5595; Rev 10/10 DS1646/DS1646P Nonvolatile Timekeeping RAM www.maxim-ic.com FEATURES Integrates NV SRAM, Real-Time Clock, Crystal, Power-Fail Control Circuit and Lithium Energy Source Clock Registers
128Kx8 CMOS MONOLITHIC EEPROM SMD
128Kx8 CMOS MONOLITHIC EEPROM SMD 5962-96796 WME128K8-XXX FEATURES Read Access Times of 125, 140, 150, 200, 250, 300ns JEDEC Approved Packages 32 pin, Hermetic Ceramic, 0.600" DIP (Package 300) 32 lead,
2.2x1.4mm SURFACE MOUNT LED LAMP. Descriptions. Features. Package Dimensions
2.2x1.4mm SURFACE MOUNT LED LAMP ATTENTION OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Part Number: AA2214VR4D1S-C1 Cool White Features 2.2mm x 1.4mm, 1.3mm high. Low power
LCA710STR. Single Pole, Normally Open OptMOS Relay INTEGRATED CIRCUITS DIVISION
LCA7 Single Pole, Normally Open OptMOS Relay Parameter Rating Units Blocking Voltage 6 V P Load Current A rms / A DC On-Resistance (max. Features Low On-Resistance:. High Current Handling Capability: A
Z1SMA4736A Z1SMA4757A
1W Surface Mount Zener Diodes Features For surface mounted applications in order to optimize board space Built-in strain relief Glass passivated junction Low inductance High temperature soldering guaranteed:
MAXIM INTEGRATED PRODUCTS
MAX6106EUR Rev. A RELIABILITY REPORT FOR MAX6106EUR PLASTIC ENCAPSULATED DEVICES February 14, 2003 MAXIM INTEGRATED PRODUCTS 120 SAN GABRIEL DR. SUNNYVALE, CA 94086 Written by Reviewed by Jim Pedicord
CPC2025NTR. 400V Dual Normally-Open Single-Pole 8-Pin SOIC OptoMOS Relay INTEGRATED CIRCUITS DIVISION
4V Dual Normally-Open Single-Pole 8-Pin SOIC OptoMOS Relay Parameter Rating Units Blocking Voltage 4 V P Current 1 ma rms / ma DC On-Resistance (max) LED Forward Current (to Activate) 2 ma Features V rms
My-MS. MM27C ,072 x 8 CMOS EPROM PRELIMINARY INFORMATION ISSI IS27C010 FEATURES DESCRIPTION FUNCTIONAL BLOCK DIAGRAM
IS27C010 ISSI MM27C010 131,072 x CMOS EPROM PRELIMINARY INFORMATION FEATURES Fast read access time: 90 ns JEDEC-approved pinout High-speed write programming Typically less than 16 seconds 5V ±10% power
MCC. Revision: /06/09 1N5338B THRU 1N5369B
Features Zener Voltage From 5.V to 5V Case Material: Molded Plastic. UL Flammability Classification Rating 94V-0 For Available Tolerances See Note Marking : Cathode band and type number Maximum Ratings:
Transient Voltage Suppressors. AK3 Series. Circuit Protection System ELECTRONICS
ELECTRONICS Transient Suppressors K3 Series Transient Suppressors - K3 Series Features Very low clamping voltage Ultra compact: less than one-tenth the size of traditional discrete solutions Sharp breakdown
CD4010C Hex Buffers (Non-Inverting)
Hex Buffers (Non-Inverting) General Description The CD4010C hex buffers are monolithic complementary MOS (CMOS) integrated circuits. The N- and P-channel enhancement mode transistors provide a symmetrical
TORX178B TORX178B FIBER OPTIC RECEIVING MODULE FOR DIGITAL AUDIO INTERFACE. 1. Maximum Ratings (Ta = 25 C) FIBER OPTIC RECEIVING MODULE
FIBER OPTIC RECEIVING MODULE TORX178B FIBER OPTIC RECEIVING MODULE FOR DIGITAL AUDIO INTERFACE Unit: mm Conforms to EIAJ Standard CP 1201 (For Digital Audio Interface including Fiber Optic inter connections).
Article No. 6GK59230PS003AA2 6GK59240PS001AA2 Product Name. Power Supply SCALANCE PS924 PoE Input: 120/230V AC; Output: 54V/ 1.
Product Name Type of power supply Electrical data Input Waveform of the input Supply Power Supply SCALANCE PS924 PoE Input: 120/230V AC; Output: 54V/ 1.6A DC; NEC Class 2 single-phase AC Power Supply SCALANCE
LCA127STR. Single-Pole, Normally Open OptoMOS Relay INTEGRATED CIRCUITS DIVISION
Single-Pole, Normally Open OptoMOS Relay Parameter Ratings Units Blocking Voltage V P Load Current ma rms / ma DC On-Resistance (max Features 37V rms Input/Output Isolation Low Drive Power Requirements
LCA110LSTR. Single Pole, Normally Open OptoMOS Relay INTEGRATED CIRCUITS DIVISION
LCA11L Single Pole, Normally Open OptoMOS Relay Parameter Ratings Units Blocking Voltage 3 V P Load Current 12 ma rms & ma DC On-Resistance (max 3 Features Built-in Current Limiting 37V rms Input/Output
MAX705-MAX813L Low-Cost, µp Supervisory Circuit
General Description The MAX705-MAX708/MAX813L microprocessor (µp) supervisory circuits reduce the complexity and number of components required to monitor power-supply and battery functions in µp systems.
Description. Features. Continuous RA8 Series RA16 Series RA22 Series Units. ) 4 to to to 275 V DC Voltage Range (V M(DC)
RA Varistor Series RoHS Description The RA Series transient surge suppressors are varistors (MOVs) supplied in a low-profile box that features a precise seating plane to increase mechanical stability for
Long seller backed by product variety and high reliability
Long seller backed by product variety and high reliability DS RELAYS RoHS compliant FEATURES 1. Breakthrough height of 9.8 mm.386 inch beats the 1 mm.394 inch limit 1c and 2c all have the same height (9.8
ATF20V8B. High Performance Flash PLD. Features. Block Diagram. Pin Configurations
Features Industry Standard Architecture Emulates Many 24-Pin PALs Low Cost Easy-to-Use Software Tools High Speed Electrically Erasable Programmable Logic Devices 7.5 ns Maximum Pin-to-Pin Delay Several
Advanced Lantern 1.0 Kit. Introduction to the Advanced Lantern 1.0 Kit
Advanced LED Lantern 1.0 Instruction Manual Eastern Voltage Research, LLC Introduction to the Advanced Lantern 1.0 Kit Thank you for purchasing the Advanced Lantern 1.0 Kit. This kit is an advanced microprocessor
CAT28C K-Bit Parallel EEPROM
256K-Bit Parallel EEPROM HALOGENFREE LEAD TM FREE FEATURES Fast read access times: 120/150ns Low power CMOS dissipation: Active: 25 ma max Standby: 150 µa max Simple write operation: On-chip address and
SZAF5.1A~SZAF220A ZENER DIODE 1.5W
DESCRIPTION The are available in SMAF Package ORDERING INFORMATION Package Type Part Number SZAF5.1A SZAF36A SZAF5.6A SZAF39A SZAF6.2A SZAF43A SZAF6.8A SZAF47A SZAF7.5A SZAF51A SZAF8.2A SZAF56A SZAF9.1A
Long seller backed by product variety and high reliability
Long seller backed by product variety and high reliability DS RELAYS Compliance with RoHS Directive FEATURES 1. Breakthrough height of 9.8 mm.386 inch beats the 1 mm.394 inch limit 1c and 2c all have the
DS1845 Dual NV Potentiometer and Memory
www.maxim-ic.com FEATURES Two linear taper potentiometers -010 one 10k, 100 position & one 10k, 256 position -050 one 10k, 100 position & one 50k, 256 postition -100 one 10k, 100 position & one 100k, 256
Tube Liquid Sensor OPB350 / OCB350 Series (Calibration Circuit Available)
Features: Can identify if liquid is present in clear tubes that have an outside diameter of 1/16 [1.6mm], 1/8" [3.2mm], 3/16" [4.8 mm] or 1/4" [6.3 mm] Opaque plastic housing enhances ambient light rejection
Features. Samples. Units Continous: Steady State Applied Voltage: DC Voltage Range (VM(DC)) 150 to 970 V AC Voltage Range (V M(AC)RMS
S 34S Varistor Series RoHS Description The Littelfuse S 34S thermally protected varistor is a self-protected device. It consists of a 34mm square varistor with an integral thermal designed to open in the
BAT42W/BAT43W SURFACE MOUNT SCHOTTKY BARRIER DIODE
Features: Low Turn-on Voltage Fast Switching PN Junction Guard Ring Transient and ESD Protection Designed for Surface Mount Application Plastic Material UL Recognition Flammability Classification 94V-O
LCA182STR. Single Pole, Normally Open OptMOS Relay INTEGRATED CIRCUITS DIVISION
Single Pole, Normally Open OptMOS Relay Parameter Rating Units Blocking Voltage 3 V P Load Current 12 ma rms / ma DC On-Resistance (max 3 Input Control Current.2 ma Features Very Low Input Control Current
DS1814/DS1819 5V and 3.3V MicroMonitor
5V and 3.3V MicroMonitor www.maxim-ic.com FEATURES Halts and restarts an out-of-control microprocessor Holds microprocessor in check during power transients Automatically restarts microprocessor after
Single-Phase 6.0A Glass Passivated Bridge Rectifier
0 Single-Phase 6.0A Glass Passivated Bridge Rectifier 0 Features D3K Glass passivated die construction Low forward voltage drop High current capability High surge current capability Designed for surface
ELECTROSÓN. 1N53 Series. 5 Watt Surmetic 40 Zener Voltage Regulators
5 Watt Surmetic 40 Zener Voltage Regulators This is a complete series of 5 Watt Zener diodes with tight limits and better operating characteristics that reflect the superior capabilities of silicon oxide
PM1206STR. AC Power Switch INTEGRATED CIRCUITS DIVISION
AC Power Switch Parameter Rating Units AC Operating Voltage 26 V rms Load Current 5 ma rms On-State Voltage Drop (I L =5mA rms ) 1.4 V rms Features Load Current up to.5a rms Blocking Voltages up to 6V
CHENMKO ENTERPRISE CO.,LTD
CHENMKO ENTERPRISE CO.,LTD SURFACE MOUNT ZENER SILICON PLANAR POWER ZENER DIODES VOLTAGE RANGE.V TO 9V MMPZBGP THRU MMPZBGP FEATURE * High temperature soldering type. * ESD rating of class (> kv) per human
QUICKSWITCH PRODUCTS HIGH-SPEED CMOS 10-BIT BUS SWITCH
QUICKSWITCH PRODUCTS HIGH-SPEED CMOS 10-BIT BUS SWITCH IDTQS338 FEATURES: Enhanced N channel FET with no inherent diode to Vcc 5Ω bidirectional switches connect inputs to outputs Zero propagation delay,
SST 29EE V-only 1 Megabit Page Mode EEPROM
Data Sheet SST 29EE010 July 1996 5.1 Features: Single 5.0-Volt Read and Write Operations CMOS SuperFlash EEPROM Technology Endurance: 100,000 Cycles (typical) Greater than 100 years Data Retention Low
ENC 125 T/E REFERENCE MANUAL. Acu-Rite Companies Inc.
ENC 125 T/E REFERENCE MANUAL Acu-Rite Companies Inc. ENC 125 T/E Page Introduction... 2 Mounting Preparation... 3 Mounting Information... 4 Encoder Dimensions - ENC 125 T (top mount)... 5 Encoder Dimensions
MX27C K-BIT [32K x 8] CMOS EPROM FEATURES GENERAL DESCRIPTION BLOCK DIAGRAM PIN CONFIGURATIONS PIN DESCRIPTION
![MX27C K-BIT [32K x 8] CMOS EPROM FEATURES GENERAL DESCRIPTION BLOCK DIAGRAM PIN CONFIGURATIONS PIN DESCRIPTION](/thumbs/78/78720826.jpg "MX27C K-BIT [32K x 8] CMOS EPROM FEATURES GENERAL DESCRIPTION BLOCK DIAGRAM PIN CONFIGURATIONS PIN DESCRIPTION")
FEATURES 32K x 8 organization Single +5V power supply +125V programming voltage Fast access time: 45/55/70/90/100/120/150 ns Totally static operation Completely TTL compatible 256K-BIT [32K x 8] CMOS EPROM
DS1831C/D/E. 3.3V/2.5V Multisupply MicroMonitor
3.3V/2.5V Multisupply MicroMonitor www.maxim-ic.com FEATURES 2.5V power-on reset 3.3V power-on reset Two referenced comparators with separate outputs for monitoring additional supplies Internal power is
mic+600/dd/tc Extract from our online catalogue: Current to:
Extract from our online catalogue: mic+600/dd/tc Current to: 2017-03-17 microsonic GmbH / Phoenixseestraße 7 / 44263 Dortmund / Germany / T +49 231 975151-0 / F +49 231 975151-51 / E info@microsonic.de
ICE27C Megabit(128KX8) OTP EPROM
1- Megabit(128KX8) OTP EPROM Description The is a low-power, high-performance 1M(1,048,576) bit one-time programmable read only memory (OTP EPROM) organized as 128K by 8 bits. It is single 5V power supply
FAST CMOS SYNCHRONOUS PRESETTABLE BINARY COUNTERS
Integrated Device Technology, Inc. FAST CMOS SYNCHRONOUS PRESETTABLE BINARY COUNTERS IDT54/74FCT161/A/C IDT54/74FCT163/A/C FEATURES: IDT54/74FCT161/163 equivalent to FAST speed IDT54/74FCT161A/163A 35%
3.5x2.8mm SURFACE MOUNT LED LAMP. Features. Descriptions. Package Dimensions
3.5x2.8mm SURFACE MOUNT LED LAMP ATTENTION OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Part Number: AAAF3529LSEEZGKQBKS Features Outstanding material efficiency. Low power
VT-820 VT-820. Temperature Compensated Crystal Oscillator Previous Vectron Model VTM3. Description
VT-820 Temperature Compensated Crystal Oscillator Previous Vectron Model VTM3 VT-820 Description Vectron s VT-820 Temperature Compensated Crystal Oscillator (TCXO) is a quartz stabilized, clipped sine
Phototriac Coupler for the Industrial Machinery, Consumer Electronics, and SSR Markets FEATURES
VDE Pending Phototriac Coupler for the Industrial Machinery, Consumer Electronics, and SSR Markets Phototriac Coupler FEATURES TYPICAL APPLICATIONS ZC Zero-cross circuit. Two types available: Non zero-cross
24AA16/24LC16B. 16K I 2 C Serial EEPROM. Device Selection Table. Description: Features: Package Types. Block Diagram. Temp. Ranges.
6K I C Serial EEPROM Device Selection Table Part Number Features: Vcc Range Max. Clock Frequency Temp. Ranges A6.7-. 00 khz () I LC6B.-. 00 khz I, E Note : 00 khz for
Technical Data Sheet Photolink- Fiber Optic Receiver
Technical Data Sheet Photolink- Fiber Optic Receiver Features 1. High PD sensitivity optimized for red light 2. Data : NRZ signal 3. Low power consumption for extended battery life 4. Built-in threshold
250 Mbps Transceiver in LC FB2M5LVR
250 Mbps Transceiver in LC FB2M5LVR DATA SHEET 650 nm 250 Mbps Fiber Optic Transceiver with LC Termination LVDS I/O IEC 61754-20 Compliant FEATURES LC click lock mechanism for confident connections Compatible
HEMP & IEMI PROTECTION FILTERS FOR MAINS POWER LINES
HEMP & IEMI PROTECTION FILTERS HEMP & IEMI PROTECTION FILTERS FOR MAINS POWER LINES MEETS ELECTRICAL POINT-OF-ENTRY REQUIREMENTS OF MIL-STD-188-125 PARTS 1 & 2 AND DEF STAN 59-188 PARTS 1 & 2 FOR SHORT
CPC1824NTR. 4V Output Solar Cell INTEGRATED CIRCUITS DIVISION
4V Output Solar Cell Parameter Rating Units Open Circuit Voltage 4 V Short Circuit Current 00 ua * Direct sunlight (Approximately 6000 lux) Features 4V Output Triggers with Natural Sunlight Provides True
Over 5,000 products High Performance Adapters and Sockets Many Custom Designs Engineering Electrical and Mechanical ISO9001:2008 Registration
Overview Company Overview Over 5,000 products High Performance Adapters and Sockets Many Custom Designs Engineering Electrical and Mechanical ISO9001:2008 Registration Adapter Technology Overview Pluggable
Description. Features
Metal-Oxide s (MOVs) Industrial High Energy Thermally Protected s > TMOV 34S Series TMOV 34S Series ohs Description Agency Approvals Agency Standard Agency File Number The Littelfuse TMOV 34S thermally
NB2304A. 3.3V Zero Delay Clock Buffer
3.3V Zero Delay Clock Buffer The NB304A is a versatile, 3.3 V zero delay buffer designed to distribute high speed clocks in PC, workstation, datacom, telecom and other high performance applications. It
QUICKSWITCH PRODUCTS HIGH-SPEED CMOS 10-BIT BUS SWITCH WITH FLOW-THROUGH PINOUT
QUICKSWITCH PRODUCTS HIGH-SPEED CMOS 10-BIT BUS SWITCH WITH FLOW-THROUGH PINOUT IDTQS361 FEATURES: Enhanced N channel FET with no inherent diode to Vcc 5Ω bidirectional switches connect inputs to outputs
US1881 CMOS Multi-purpose latch
Features and Benefits Chopper stabilized amplifier stage Optimized for BDC motor applications New miniature package / thin, high reliability package Operation down to 3.5V CMOS for optimum stability, quality
Descriptions. Applications
3.5x3.5 mm SMD CHIP LED LAMP ATTENTION OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Part Number: AA3535QB25Z1S Blue Features White SMD package, silicone resin. Low thermal
CPC1540GSTR. Features Integrated Active Current-Limit Protection Thermal Shutdown Guaranteed Turn-On: 2mA Input Control Current 350V P
Single-Pole, Normally Open OptoMOS Relay with Integrated Current Limit and Thermal Shutdown Parameter Rating Units Load Voltage 350 V P Load Current 120 ma Maximum On-Resistance 25 Input Control Current
VGA Port Companion Circuit
GA Port Companion Circuit Features Single chip solution for the GA port interface Includes ESD protection, level shifting, and RGB termination Seven channels of ESD protection for all GA port connector
MAXIM INTEGRATED PRODUCTS
MAX6628MKA Rev. A RELIABILITY REPORT FOR MAX6628MKA PLASTIC ENCAPSULATED DEVICES September 30, 2003 MAXIM INTEGRATED PRODUCTS 120 SAN GABRIEL DR. SUNNYVALE, CA 94086 Written by Reviewed by Jim Pedicord
Description. Applications
3.5x3.5 mm SMD CHIP LED LAMP PRELIMINARY SPEC ATTENTION OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Features White SMD package, silicone resin. Low thermal resistance. Compatible