System Configuration Guide (V.4) (October / 2000)

Transcription

1 Guide (V.4) (October / 2000) Notes PRIMERGY HS910 PRIMERGY MS610 PRIMERGY MS380 PRIMERGY ES320 PRIMERGY ES280 PRIMERGY ES210 PRIMERGY ES200 PRIMERGY TS220/120 External Disk Array External Devices Rackmount Hardware Index The numbers on the left hand side of each page correspond to the various options available with teamservers as follows 1 CPU slot 2 RAM module slot inch HDD Bay 4 5 inch Bay 5 RS-232C 6 PCI slot 7 ISA slot 8 Redundant PSU 9 Others Key to Or And

2 NOTES Disk array configuration Physical pack A collection of physical HDDs comprising a RAID. Logical drive The logical drive (e.g. D: ) as seen by the Operating System. Partition One of the logical access units into which a logical drive is divided. Physical pack HDD HDD HDD HDD Partition 1 Partition 2 Logical drive A Logical drive B * Drives can be divided into partitions. Logical drive C <Restrictions> (1) Each physical pack must contain the same type(size) of HDDs. (2) Maximum logical drive size is 2TB (GP5U141/GP5-143/144/145/146/148). (3) The number of HDDs comprising a physical pack is as shown below. RAID Level Description HDDs Capacity of logical drives RAID 0 The data is broken down into blocks, 2~8(16) The capacity of logical drive is same each on a separate disk drive as the capacity of connected HDD. RAID 1 Duplicates the disk and writes 2 The capacity of the logical drive is the same data onto two disks. half the capacity of connected HDD. RAID 5 The data is broken down into blocks 3~8(16) The capacity of each logical drive is and each blocks is written together the number of connected HDDs - 1). with parity bits on a separate disk drive. *1 RAID 6 Duplicates the disk and broken down 3~8(16) The capacity of each logical drive into blocks, each on a is the half the capacity of connected on a separate disk. (RAID0+1) HDD. (GP5-143/144/145/146/148) *2 *2 *2 *1 GP5U141: RAID6 is available with Firmware 4.04-F-56 or greater *2 GP5-148 : Up to 16 HDD can be connected (4) The same RAID level must be use when dividing a physical pack into a number of logical drives. (5) A physical pack must contain only HDDs which are connected by the same RAID card. (6) A RAID card can support more than one physical pack. ( even if different RAID levels) (7) Same capacity HDDs connected to the same RAID Card, must also have the same rpm speed. 9GB 7200rpm 9GB 7200rpm 9GB 10000rpm This must be 9GB with 7200rpm HDD! RAID Hard disk cabinet / RAID card / SCSI card GP5MS623A/GP5UR1DC5: Note: The operating System must be installed on an internal hard disk. (Except HS910) RAID card (GP5U141/GP5-144/145/146/148) 1.Up to two Hard disk cabinets can be connected to one RAID card. (Up to three can be connected with one GP5-144 card) 2.When using GP5U141 in ES280, it cannot be used for both external disk array (GP5UR1DC5 / GP5MS623A) and internal disk array. 3.Internal and external array devices cannot be connected to the same channel. 4.GP5-144/145/146 can only be used with GP5-144/145/146, they cannot be mixed with GP5U141/GP5-143/148) 5.Up to two 146 can be used for internal array configuration in MS380 6.When installing three RAID cards in MS380, the internal HDD must be connected using GP GP5-148 cannot be used with other RAID Card. (This restriction will be eliminated later) 8.One GP5-148 can be installed in a server. (This restriction will be eliminated later) 2

3 NOTES RAID card (GP5-143) Only for use with internal devices. Only one of these RAID cards can be used per server. Restrictions and support status on Windows(R)2000 The restrictions (only one GP5U141/GP5-143/144/146 RAID Card can be installed per a Server on Windows(R)2000) have been cancelled as of beginning of October. Driver software for Windows2000 can be downloaded from PRIMERGY web-site ( The RAID Card products with new Windows2000 driver will be shipped as of end October. SCSI card (GP5-125 / GP5-126 / GP5-127) 1.Internal and external devices cannot be connected to the same SCSI card. 2.Only one Hard disk cabinet can be connected. (Daisy chain connection is not available) Number of connectable Hard Disk Cabinets Hard Disk Node Product TS120 ES200 ES210 ES280 ES320 MS380 MS610 HS910 TS220 Hard Disk Cabinet GP5MS623A Storage System GP5UR1DC Mountable Card options HS910 MS610 Maximum Maximum number number Cards Product ID Bus of cards Total REMARKS Cards Product ID Bus of cards Total REMARKS mounted mounted SCSI card GP5-123 PCI For external disk array SCSI card GP5-123 PCI64 2 For external disk array (Ultra Wide Diff) (Ultra Wide Diff) 4 8 SCSI card GP5-127 PCI32 6 SCSI card GP5-127 PCI64 3 (Ultra2 Wide LVD) (Ultra2 Wide LVD) 3 RAID card GP5-144/1441 PCI64 7 RAID card GP5-144/1441 PCI64 3 (Ultra2 Wide LVD) (Ultra2 Wide LVD) RAID card GP5-145/146 PCI64 7 RAID card GP5-145/146 PCI64 2 (Ultra2 Wide LVD) (Ultra2 Wide LVD) RAID card GP5-148 PCI64 3* RAID card GP5-148 PCI64 3* (Ultra160) (Ultra160 ) LAN card GP5-183 PCI Giga LAN (1000Base-SX) LAN card GP5-185 PCI32 3 LAN card GP5-183 PCI Giga LAN (100Base-TX) (1000Base-SX) LAN card GP5-186 PCI32 1 Dual Port LAN LAN card GP5-185 PCI32 3 (100Base-TX) (100Base-TX) LAN card GP5-187 PCI32 3 IPsec LAN LAN card GP5-186 PCI32 1 Dual Port LAN (100Base-TX) (100Base-TX) LAN card Standard PCI32 1 LAN card GP5-187 PCI32 3 IPsec LAN (100Base-TX) equipment (100Base-TX) Server Monitor Module GP5USM103 PCI Server Monitor Module GP5USM103 PCI

4 NOTES MS380 Maximum Maximum number number Cards Product ID Bus of cards Total REMARKS Cards Product ID Bus of cards Total REMARKS mounted mounted SCSI card GP5-123 PCI32 2 External disk array SCSI card GP5-127 PCI32 3 External HDD (Ultra Wide Diff) 3 (Ultra2 Wide LVD) 3 SCSI card GP5-127 PCI External HDD RAID card GP5-143 PCI Internal array configuration (Ultra2 Wide LVD) (Ultra2 Wide LVD) RAID card GP5-144/1441 PCI64 3 Internal/External array RAID card GP5-144 PCI64 2 Internal/External array (Ultra2 Wide LVD) configuration (Ultra2 Wide LVD) configuration RAID card GP5-145/146 PCI64 2 Internal/External array RAID card GP5-145/146 PCI64 2 Internal/External array (Ultra2 Wide LVD) configuration (Ultra2 Wide LVD) configuration RAID card GP5-148 PCI64 2* Internal/External array (Ultra160) configuration LAN card GP5-183 PCI64 1 Giga LAN LAN card GP5-183 PCI64 1 Giga LAN (1000Base-SX) 3 (1000Base-SX) 3 LAN card GP5-185 PCI32 3 LAN card GP5-185 PCI32 3 (100Base-TX) (100Base-TX) LAN card GP5-187 PCI32 3 IPsec LAN LAN card GP5-186 PCI32 1 Dual Port LAN (100Base-TX) (100Base-TX) Server Monitor Module GP5USM103 PCI LAN card GP5-187 PCI32 3 IPsec LAN (100Base-TX) Server Monitor Module GP5USM103 PCI ES280 Maximum Maximum number number Cards Product ID Bus of cards Total REMARKS Cards Product ID Bus of cards Total REMARKS mounted mounted SCSI card GP5-125 PCI Only for external SCSI card GP5-127 PCI32 3 Internal HDD/Backup device (Ultra Wide) 3 SCSI devices (Ultra 2Wide LVD) /External device RAID card GP5U141 PCI32 2 Internal/External RAID card GP5-143 PCI Internal array configuration (Ultra Wide) 2 array configuration (Ultra2 Wide LVD) 2 3 RAID card GP5-143 PCI32 1 Only for internal array RAID card GP5-145/146 PCI64 1 External array configuration (Ultra Wide) configuration (Ultra2 Wide LVD) LAN card GP5-183 PCI Giga LAN LAN card GP5-183 PCI Giga LAN (1000Base-SX) (1000Base-SX) LAN card GP5-185 PCI32 3 LAN card GP5-185 PCI32 3 (100Base-TX) (100Base-TX) LAN card GP5-187 PCI32 3 IP sec LAN LAN card GP5-186 PCI32 1 Dual Port LAN (100Base-TX) (100Base-TX) LAN card GP5-187 PCI32 3 IPsec LAN (100Base-TX) Server Monitor Module GP5USM103 PCI Server Monitor Module GP5USM103 PCI ES200 ES320 ES210 TS220/120 Maximum Maximum number number Cards Product ID Bus of cards Total REMARKS Cards Product ID Bus of cards Total REMARKS mounted mounted SCSI card GP5-126 PCI32 1 Internal HDD/Backup RAID card GP5-148 PCI64 1 Internal array configuration for (Ultra 2Wide LVD) 3 device/external device (Ultra160) TS220 SCSI card GP5-127 PCI Internal Backup device LAN card GP5-183 PCI64 1 Giga LAN (Ultra 2Wide LVD) /External device (1000Base-SX) 1 RAID card GP5-143 PCI Internal array LAN card GP5-185 PCI64 1 (Ultra2 Wide LVD) 2 configuration (100Base-TX) RAID card GP5-145/146 PCI64 1 External array LAN card GP5-186 PCI64 1 Dual Port LAN (Ultra2 Wide LVD) configuration (100Base-TX) LAN card GP5-183 PCI64 1 Giga LAN LAN card GP5-187 PCI64 1 IPsec LAN (1000Base-SX) 3 (100Base-TX) LAN card GP5-185 PCI32 3 (100Base-TX) LAN card GP5-186 PCI32 1 IPsec LAN (100Base-TX) LAN card GP5-187 PCI32 3 IPsec LAN (100Base-TX) Server Monitor Module GP5USM103 PCI Restrictions * When GP5-186 is mounted, one other LAN Card (GP5-183/185/187) can be mounted. * GP5-148 cannot be used with other RAID Card. (This restriction will be eliminated later) * More than two GP5-148 cannot be mounted in a server. (This restriction will be eliminated later) 4

5 NOTES Mountable Hard Disk Drives for each model Main unit Product Available HDD Interface Height Revolution Remarks Product ID TS120 Hard disk drive-30gb GP5-HD3E2 UltraDMA/66*1 1" 5400rpm IDE HDD TS220 Hard disk drive-9gb GP5-HDH9B Ultra160 1" 7200rpm Hard disk drive-18gb GP5-HDH88 Ultra160 1" 7200rpm Hard disk drive-36gb GP5-HDH63 Ultra160 1" 10000rpm ES200 Hard disk drive-9gb GP5-HD9G3 Ultra2Wide 1" 7200rpm GP5-HD9G3C Ultra2Wide 1" 7200rpm For mounting in 5" bay GP5-HD9G4 Ultra2Wide 1" 10000rpm Hard disk drive-18gb GP5-HD8G1 Ultra2Wide 1" 7200rpm GP5-HD8G1C Ultra2Wide 1" 7200rpm For mounting in 5" bay GP5-HD8G2 Ultra2Wide 1" 10000rpm Hard disk drive-36gb GP5-HD6G1 Ultra2Wide 1" 10000rpm Hard disk drive-30gb GP5-HD3E2 UltraDMA/66*2 1" 5400rpm IDE HDD ES210 Hard disk drive-9gb GP5-HD9G3 Ultra2Wide 1" 7200rpm GP5-HD9G3C Ultra2Wide 1" 7200rpm For mounting in 5" bay GP5-HD9G4 Ultra2Wide 1" 10000rpm Hard disk drive-18gb GP5-HD8G1 Ultra2Wide 1" 7200rpm GP5-HD8G1C Ultra2Wide 1" 7200rpm For mounting in 5" bay GP5-HD8G2 Ultra2Wide 1" 10000rpm Hard disk drive-36gb GP5-HD6G1 Ultra2Wide 1" 10000rpm Hard disk drive-30gb GP5-HD3E2 UltraDMA/66*2 1" 5400rpm IDE HDD ES280 Hard disk drive-9gb GP5-HD9G3 Ultra 2Wide *3 1" 7200rpm Non Hotplug Hard disk drive-9gb GP5-HDH96 Ultra 2Wide *3 1" 7200rpm Hard disk drive-18gb GP5-HD8G1 Ultra 2Wide *3 1" 7200rpm Non Hotplug Hard disk drive-18gb GP5-HDH83 Ultra 2Wide *3 1" 7200rpm ES320 Hard disk drive-9gb GP5-HDH9C Ultra2Wide 1" 7200rpm Hard disk drive-18gb GP5-HDH89 Ultra2Wide 1" 7200rpm Hard disk drive-9gb GP5-HDH9D Ultra160 1" 10000rpm Hard disk drive-18gb GP5-HDH8A Ultra160 1" 10000rpm Hard disk drive-36gb GP5-HDH63 Ultra160 1" 10000rpm MS380 Hard disk drive-9gb GP5-HDH96 Ultra2Wide 1" 7200rpm Hard disk drive-18gb GP5-HDH83 Ultra2Wide 1" 7200rpm Hard disk drive-9gb GP5-HDH9A Ultra2Wide 1" 10000rpm Up to six can be mounted Hard disk drive-18gb GP5-HDH87 Ultra2Wide 1" 10000rpm Up to six can be mounted Hard disk drive-36gb GP5-HDH63 Ultra160 1" 10000rpm Up to six can be mounted MS610 Hard disk drive-9gb GP5-HDH9B Ultra160 1" 7200rpm Hard disk drive-9gb GP5-HDH9A Ultra 160 1" 10000rpm Hard disk drive-18gb GP5-HDH88 Ultra160 1" 7200rpm Hard disk drive-18gb GP5-HDH87 Ultra 160 1" 10000rpm Hard disk drive-36gb GP5-HDH63 Ultra 160 1" 10000rpm HS910 Hard disk drive-9gb GP5-HDH9AT Ultra 160 *4 1" 10000rpm Hard disk drive-18gb GP5-HDH87T Ultra 160 *4 1" 10000rpm Hard disk drive-36gb GP5-HDH63T Ultra 160 *4 1" 10000rpm *1 IDE HDD of TS120 works on PIO mode. *2 ES200/ES210 equips Ultra DMA/33 IDE controller which limits Ultra DMA/66 HDDs to Ultra DMA/33 bus speeds. *3 ES280 equips Ultra Wide SCSI controller which limits Ultra2 Wide SCSI HDDs to Ultra Wide SCSI bus speeds. *4 HS910 equips Ultra2 Wide SCSI controller which limits Ultra160 HDDs to Ultra2 Wide SCSI bus speeds. Configuration To Order Configuration To Order (CTO) is available with PRIMERGY HS910/MS610/MS380/ES280/ES210/ES200. Products are delivered with options (HDD, Memory, Backup device, etc.) already mounted as per customer requirements. 1. How shipped [Main unit] (1) CPU+Chassis+Memory + (2) Mount option in free slots (3) Standard Memory / Drive Cage conversion Shipment 2. Applicable products for CTO (1)Main unit HS910 / MS610 / MS380 / ES320 / ES280 / ES210 / ES200 / TS220 / TS120 Storage System (GP5UR1DC5) / Hard Disk Cabinet (GP5MS623A) / Backup Cabinet (GP5UR1BC2) (2) Option (GP5BXXX) All options which name is with prefix "GP5B" are available for CTO. 5

6 NOTES Rackmounting Kit When mounting current Rackmount model into new "Black Rack(GP5-R1RC6/GP5-R2RC3)" and it's "Coupling Kit (GP5-R1RC7/GP5-R2RC4)", "Rackmounting Kit" is required for mounting. Which Rackmounting Kit is applicable, please refer to the chart below. Restrictions "White" Component Shelf Kit (GP5-R1TB4) cannot be mounted in "Black" Rack (GP5-R1RC6 /GP5-R1RC7, GP5-R2RC3/GP5-R2RC4) "White" Keyboard Monitor Shelf Kit (GP5-R1TB5) cannot be mounted in "Black" Rack (GP5-R1RC6 /GP5-R1RC7, GP5-R2RC3/GP5-R2RC4) Nodes Applicable Kits Rackmounting Kit GP5-R1RK1 Rackmounting Kit GP5-R1RK2 Rackmounting Kit GP5-R1RK3 Rackmounting Kit GP5-R1RK4 Rackmounting Kit GP5-R1RK5 Rackmounting Kit GP5-R1RK7 Rackmounting Kit GP5-R1RK8 teamserver C8xxi teamserver G8xxi/L8xxi teamserver MS600 teamserver HS900 GRANPOWER5000 Model280 GRANPOWER5000 Model380/580 GRANPOWER5000 MS600 GRANPOWER5000 HS900 Others PRIMERGY ES280 PRIMERGY MS380 PRIMERGY MS610 PRIMERGY HS910 Storage System Flat Display Backup Cabinet Differentiation between Servervisor and Intel LANDesk Server Manager Server monitoring software (Servervisor V1.0 and Intel LANDesk Server Manager V6.0) is bundled with all teamservers Differences in function between Servervisor and Intel LANDesk Server Manager are indicated below: Items Servervisor V1.0 Intel LANDesk Server Manager V6.0 Product TS120/TS220 All products ES200/ES210/ES280/ES320/MS380 MS610/HS910 Main function Server status monitoring Server status monitoring Error notification Error message Remote control WindowsNT performance monitoring (e.g. CPU/Memory utilization) Alert function Internet mail transmission Internet mail transmission SNMP Trap transmission SNMP Trap transmission Message box Message box (*On the monitored server) (*On the monitored server) Pager Activation by program Broadcast to connected clients SMM support No Yes Required memory capacity 6~10MB 32~64MB Advantage Servervisor provides the minimum functions LDSM is suitable for systems employing required for server management to reduce remote central monitoring or the amount of resources used, SMM based monitoring to provide making it convenient for a small-scale system a more powerful server management function. without a dedicated manager. - Powerful functions - Simplified operation, light-weight - Easy to use - Remote monitoring is provided by System Walker plus LiveHelp. Remote control and WindowsNT performance monitor are provided by System Walker. - If the message box is to be displayed for server error detection, the message box must be logged on to the server. Errors that occur while the message box is not logged on can be reported using Internet mail and SNMP Trap. The event log also can be used to check whether such errors have occurred. 6

7 PRIMERGY HS910 Specification Type Rackmount Product ID GP5T9BH2R GP5T9BG2R CPU Frequency Pentium(R)lll XeonTM 700MHz Secondary cache 2MB 1MB Number of CPUs 2 (up to 8) Memory Standard 1GB (128MB x 8) Maximum 32GB (1GB x 32) Internal Bays 5-inch One (occupied by CD-ROM) CD-ROM 40X (IDE) HDD bay 1inch/1.6inch x2/hotplug Available HDD 9.1GB(10000rpm)/18.2GB(10000rpm)/36.4GB(10000rpm) Maximum 72.8GB (36.4GB x 2) Expansion slot PCI64bit 66MHz x4, PCI64bit 33MHz x 5 SCSI Interface Internal: Ultra2 Wide SCSI x 1, External: Ultra2 Wide x 1 RAID controller 2ch Ultra2 Wide (occupying one PCI slot) Network LAN(10/100 base TX) x 1 (occupying one PCI slot) Dimension (mm) 480(W)x730(D)x311(H) Rackmount7U Weight 70kg (max.) Power consumption 670W (max.) Power supply Three standard units (the third unit is for redundant) Mounting Additional Memory A memory board with 16slots is standard equipment and up to 16GB memory can be mounted. When you add more than 16GB, an additional Memory Board (GP5-RB201) is required. When using two memory boards in HS910, the same memory size must be mounted on each board. Standard Memory Board M B M B M B M B M B M B M B M B #1 #2 #3 #4 #13 #14 #15 #16 #5 #6 #7 #8 #9 #10 #11 #12 Additional Memory Board (GP5-RB201) M B M B M B M B M B M B M B M B #1 #2 #3 #4 #13 #14 #15 #16 #5 #6 #7 #8 #9 #10 #11 #12 Mounting internal devices In HS910, there are two internal HDD bays (9GB / 18GB / 36GB disks are available) Storage System (GP5UR1DC5) is required for data storage. Boot disk can be an external disk. HS910 has no internal 5" bay in chassis, so Backup cabinet (GP5UR1BC2) is required to mount backup devices. PRIMERGY HS910 Connection of internal HDD and internal backup devices Standard Channel 0 RAID Controller Channel 1 Onboard SCSI Ultra2 Wide A Ultra2 Wide B For Internal / External HDD For External HDD For Internal HDD For Backup Cabinet Internal HDD Internal backup device Connection Pattern One device is connected Two devices are connected Configuration SCSI Host Cable Internal HDD Narrow Wide Narrow Wide Narrow device Interface connect connect device x 2 device x 2 and device*2 device*3 Wide device SCSI Ultra2 Wide Onboard SCSI Cable(X1) 1) 9GB, 10,000rpm Configuration (Ultra2 Wide Ach) (Standard 2) 18GB, 10,000rpm Backup Cabinet (GP5UR1BC2) equipment) 3) 36GB, 10,000rpm Onboard external SCSI channel SCSI Cable (GP5S-832) Standard Array Ultra2 Wide RAID Controller or Cable(X2) 1) 9GB, 10,000rpm Configuration or Ultra160 RAID Card (Standard 2) 18GB, 10,000rpm (GP5-144/145/ equipment) 3) 36GB, 10,000rpm 146/148) *1 Narrow connect devices: GP5UDL201/GP5UDT301/GP5USL501/GP5-DTA101 *2 Wide connect devices: GP5-DT401/GP5-DTA102/GP5-ML301/GP5-DL351(SCSI Cable is standard equipment with all Wide connect devices) *3 Daisy chain is not available for connection of a Wide SCSI connection device to Onboard SCSI (Wide) 7

8 Connection Table GP5T9BH2R Rackmount Type 2 x Pentium(R) lll Xeon 700MHz(2MB), Memory:1GB(ECC), HDD:Option GP5T9BG2R Rackmount Type 2 x Pentium(R) lll Xeon 700MHz(1MB), Memory:1GB(ECC), HDD:Option Rackmount Type <Items> CPU Field Upgrade : Memory addition : Internal Hard Disk Drive connection External Hard Disk Drive connection Backup devices Others (NIC etc.) GoTo A GoTo B GoTo C GoTo D GoTo E GoTo F CPU Standard : 2CPUs Max : 8CPUs A: 1 CPU Field Upgrade Kit - 74 (Pentium III Xeon 700MHz (2MB) x1 GP5-FG20HT/GP5BFG20HT CPU Field Upgrade Kit - 73 (Pentium III Xeon700MHz (1MB) x1 GP5-FG20GT/GP5BFG20GT Memory Max. memory: 32GB B: 2 Additional Memory - 256MB (128MB-DIMMx2) Standard memory : 1GB (128MB-DIMMx8) GP5-RM25J/GP5BRM25J 2 Additional Memory Board Additional Memory - 512MB (256MB-DIMMx2) GP5-RB201/GP5BRB201 GP5-RM51J/GP5BRM51J C: Internal Hard Disk Up to two HDDs can be mounted in the main unit Additional Memory - 1GB (512MB-DIMMx2) GP5-RM1J/GP5BRM1J Additional Memory - 2GB (1GB-DIMMx2) GP5-RM2J/GP5BRM2J SCSI on board Max : 2 Hard Disk Drive - 9GB (Ultra160 10,000rpm) 3 (Hot Plug) GP5-HDH9AT/GP5BHDH9AT 6 Standard RAID Controller Hard Disk Drive - 18GB (Ultra160 10,000rpm) (Hot Plug) GP5-HDH87T/GP5BHDH87T Hard Disk Drive - 36GB (Ultra160 10,000rpm) (Hot Plug) GP5-HDH63T/GP5BHDH63T Standard RAID Controller Conversion Kit (GP5-146 to GP5-148) GP5B1U481 Standard RAID Controller Conversion Kit (GP5-146 to GP5-144) GP5B1U443 8

9 D: Connect with Storage System Max : 8 Hard Disk Drive - 36GB (Ultra160.10,000rpm) 6 (Hot Plug GP5-HDH63/GP5BHDH63 SCSI Card (Ultra2 Wide) SCSI Cable(3m) GP5-127/GP5B127 GP5MU823A Storage System Hard Disk Drive - 9GB (Ultra160.10,000rpm) GP5UR1DC5 (Hot Plug GP5-HDH9A/GP5BHDH9A SCSI Cable(5m) GP5S-833 Hard Disk Drive - 18GB (Ultra160.10,000rpm) (Hot Plug GP5-HDH87/GP5BHDH87 SCSI Cable(10m) GP5S-834 Hard Disk Drive - 18GB (Ultra160.7,200rpm) (Hot Plug GP5-HDH88/GP5BHDH88 Hard Disk Drive - 9GB (Ultra160.7,200rpm) (Hot Plug GP5-HDH9B/GP5BHDH9B Max : 1 Redundant Power Supply Unit GP5UR1PU1/GP5BUR1PU1 Max:8 Hard Disk Drive - 36GB (Ultra160.10,000rpm) 6 GP5-HDH63/GP5BHDH63 (Hot Plug) RAID card 32MB cache/bbu SCSI Cable Storage System Ultra2 Wide SCSI GP5S-832 GP5UR1DC5 Hard Disk Drive - 18GB (Ultra160.10,000rpm) GP5-144/GP5B144 GP5-HDH87/GP5BHDH87 (Hot Plug) RAID card SCSI Cable Hard Disk Drive - 9GB (Ultra160.10,000rpm) 64MB cache/bbu GP5S-835 GP5-HDH9A/GP5BHDH9A (Hot Plug) Ultra2 Wide SCSI GP Hard Disk Drive - 18GB (Ultra160.7,200rpm) SCSI Cable GP5-HDH88/GP5BHDH88 (Hot Plug) RAID card GP5S MB cache Ultra2 Wide SCSI Hard Disk Drive - 9GB (Ultra160.7,200rpm) GP5-145/GP5B145 GP5-HDH9B//GP5BHDH9B (Hot Plug) Redundant Power Supply Unit RAID card Max:1 GP5UR1PU1/GP5BUR1PU1 16MB cache/bbu Ultra2 Wide SCSI GP5-146/GP5B146 RAID card 64MB cache Ultra160 GP5-148/GP5B148 * GP5-148 RAID Card cannot be installed with other RAID Card * Only one GP5-148 can be installed in a HS910 9

10 Backup Devices Up to four Tape units can be mounted E: 9 SCSI Cable Backup Cabinet DLT unit (DLT7000) GP5S-832 GP5UR1BC2 GP5-DL351/GP5BDL351 Occupied two 5" bay slots DAT unit (DDS4) GP5-DT401/GP5BDT401 Tape unit (MLR3) GP5-ML301/GP5BML301 DLT unit (DLT4000) GP5UDL201/GP5BDL201 Occupied two 5" bay slots DAT unit (DDS3) GP5UDT301/GP5BDT301 Tape unit (SLR5) GP5USL501/GP5BSL501 DAT autoloader (DDS4) GP5-DTA102/GP5BDTA102 Occupied two 5" bay slots DAT autoloader (DDS3) GP5-DTA101/GP5BDTA101 Occupied two 5" bay slots Others Redundant Power Supply Unit GP5UPU151/GP5BUPU151 F: 6 LAN Card GP5-183/GP5B183 6 LAN Card GP5-185/GP5B185 6 LAN Card GP5-186/GP5B186 6 LAN Card GP5-187/GP5B187 6 Server Monitor Module GP5USM103/GP5BUSM103 10

11 PRIMERGY MS610 Specification Type Pedestal Rackmount Product ID GP5T6BH1A GP5T6BG1A GP5T6BH1R GP5T6BG1R CPU Frequency Pentium(R)lll XeonTM 700MHz Secondary cache 2MB 1MB 2MB 1MB Number of CPUs 1 (up to 4) Memory Standard 256MB (64MB x 4) Maximum 16GB (1GB x 16) VRAM 2MB VGA chip: ATI RAGEIIC(PCI) Internal Bays 5-inch Three (one occupied by CD-ROM) CD-ROM 40X (EIDE) HDD bay 1inch x 8 (up to 12bays with option)/hotplug Available HDD (Ultra160) 9.1GB(10000/7200rpm)/18.2GB(10000/7200rpm)/36.4GB(10000rpm) Maximum 291.2GB (436.8GB with 12bay cage option) Expansion slot PCI64bit 66MHz x2, PCI64bit 33MHz x4, PCI32bit 33MHz x2 SCSI Interface Ultra160 x2, Wide or Narrow x1 RAID controller Option Network LAN(10/100 base TX) x 1 (onboard) Dimension (mm) 307(W)x700(D)x500(H) 482(W)x675(D)x307(H) Rackmount7U Weight 70kg (max.) Power consumption 680W (max.) Power supply Two standard units (up to three for redundant)/hotplug Mounting Additional Memory Mount the same capacity DIMM's in units of four. (Mounting of DIMM's with different capacities or a set of less than four DIMM's is not allowed) Mount the DIMM's in ascending order of their capacity. Use DIMM slots in the order from bank A (A1 to A4) to bank D (D1 to D4) Memory Board D2 B2 C2 A2 D4 B4 C4 A4 D1 B1 C1 A1 D3 B3 C3 A3 Caution Address area of 3.5GB ~4.0GB is assigned for PCI resource, cannot be used. Cooling Kit (GP5-FN101) is required if more than three GP5-RM4N (4GB: 1GB-DIMM x 4) is installed. 11

12 Mounting internal device The following figure indicates the right adapters (Onboard SCSI channel, SCSI Card, etc.) used to mount devices in MS610 Drive Cage Conversion Kit (GP5BBU1) Applicable products MS610 - Standard Drive Cage SCSI Channel 1ch Number of mountable HDD 1inch height Hard Disk Drive x 8 (8HDDs per 1ch) - Drive Cage Conversion Kit (GP5BBU1) SCSI Channel 2ch Number of mountable HDD 1inch height Hard Disk Drive x 12 (6HDDs per 1ch x 2) 5-inch bay installation Bay1: Used for CD-ROM (IDE) (Support as standard) Bay2: SCSI ID = 4~6 (Setting on the device side), SCSI ID = 4 (CTO) DAT(DDS4, DDS3), Tape Unit(MLR3, SLR5) can be installed in this bay Bay3: SCSI ID = 4~6 (Setting on the device side), SCSI ID = 5 (CTO) DAT(DDS4, DDS3), DAT Autoloader(DDS4, DDS3), Tape Unit(MLR3, SLR5), DLT Unit(DLT7000, DLT4000) can be installed in this bay Note: A DAT Autoloader, DLT unit installed in 5-inch bay 3 will also occupy bay2 because of it's height. In some case, a separate SCSI Card is required when installing a Tape Unit (MLR3), DAT(DDS4), DAT Autoloader(DDS4) or DLT(DLT7000) in a 5-inch bay. See diagram below. Connection of internal HDD and internal backup devices The following figure indicates the correct adapters (Onboard SCSI channel, SCSI Card, etc.) to use to mount devices in MS610 Mother Board of MS610 Narrow For backup device (Narrow) Onboard SCSI Wide For backup device (Wide) Select either of the SCSI channel Ultra160 A For HDD Ultra160 B For HDD Internal HDD Internal backup device Connection Pattern One device is connected Two devices are connected Configuration Drive Cage SCSI Host Cable Internal HDD Narrow Wide Narrow Wide Narrow device Interface connect connect device x 2 device x 2 and device*2 device*3 Wide device Cable(X1) 1) 9GB, 7,200rpm Standard Ultra 160 Onboard SCSI (Standard 2) 18GB, 7,200rpm (8Bays) (Ultra160 A) equipment) 3) 9GB, 10,000rpm 4) 18GB, 10,000rpm 5) 36GB, 10,000rpm Wide-1 Onboard Narrow: SCSI When Drive Cable(X2) 1) 9GB, 7,200rpm Onboard Onboard Narrow-1,2 SCSI(Wide) Onboard SCSI (Narrow) Configuration Cage Ultra 160 Onboard SCSI (Standard 2) 18GB, 7,200rpm SCSI SCSI(Wide ) Onboard Conversion (Ultra160 A/B) equipment) 3) 9GB, 10,000rpm (Narrow) SCSI (Narrow) Wide-2 SCSI Card Wide: 4) 18GB, 10,000rpm Daisy chain (GP5-127) SCSI Card (GP5-127) (12Bays)*1 5) 36GB, 10,000rpm Cable(X1) 1) 9GB, 7,200rpm Standard Ultra2 Wide RAID Card (Standard 2) 18GB, 7,200rpm (8Bays) GP5-144/146(Ch0) equipment) 3) 9GB, 10,000rpm Ultra160 RAID Card 4) 18GB, 10,000rpm Array GP5-148(Ch0) 5) 36GB, 10,000rpm Configuration When Drive Ultra2 Wide RAID Card Cable(X2) 1) 9GB, 7,200rpm Cage GP5-144/146 (Ch0/1) (Standard 2) 18GB, 7,200rpm Conversion Ultra160 RAID Card equipment) 3) 9GB, 10,000rpm GP5-148 (Ch0) 4) 18GB, 10,000rpm (12Bays)*1 5) 36GB, 10,000rpm *1 Narrow connect devices: GP5UDL201/GP5UDT301/GP5USL501/GP5-DTA101 *2 Wide connect devices: GP5-DT401/GP5-DTA102/GP5-ML301/GP5-DL351(SCSI Cable is standard equipment with all Wide connect devices) *3 Daisy chain is not available for connection of a Wide SCSI connection device to Onboard SCSI (Wide) *4 SCSI Cable is standard equipment (Narrow: Main unit/wide: Backup device) 12

13 Connection Table GP5T6BH1A GP5T6BH1R GP5T6BG1A GP5T6BG1R 1CPU(Pentium(R)lllXeon700MHz/2MB)/Pedestal Type 1CPU(Pentium(R)lllXeon700MHz/2MB)/Rackmount Type 1CPU(Pentium(R)lllXeon700MHz/1MB)/Pedestal Type 1CPU(Pentium(R)lllXeon700MHz/1MB)/Rackmount Type Pedestal Type <Items> CPU Field upgrade : Go to A Memory addition : Go to B Standard memory conversion : Go to C Internal devices (Standard Drive Cage) 1.SCSI HDD connection Go to D 2. Array HDD connection Go to E 3. Internal backup device Go to F Internal devices (Drive Cage Conversion Kit) 1.SCSI HDD connection Go to G 2. Array HDD connection Go to H 3. Internal backup device Go to I Others (NIC, PSU, etc.) : Go to J Rackmount Type A: CPU 1 CPU Field Upgrade Kit -68 (Pentiumlll Xeon 700MHz (2MB) x1) GP5-FG20H/GP5BFG20H CPU Field Upgrade Kit - 67 (Pentiumlll Xeon 700MHz (1MB) x1) GP5-FG20G/GP5BFG20G Memory Max.16GB (1GB DIMM x 16) Additional Memory-4GB (1GB SDRAM-DIMMx4) B: 2 GP5-RM4N/GP5BRM4N Standard : 256MB (64MB-DIMMx4) High-Memory Cooling Kit (GP5-FN101/GP5BFN101) (Required when more than three GP5-RM4N are installed) Additional Memory-2GB(512MB SDRAM-DIMMx4) GP5-RM2N/GP5BRM2N Additional Memory-1GB(256MB SDRAM-DIMMx4) GP5-RM1N/GP5BRM1N Additional Memory-512MB(128MB SDRAM-DIMMx4) GP5-RM51N/GP5BRM51N Standard Memory conversion Additional Memory-256MB(64MB SDRAM-DIMMx4) GP5-RM25N/GP5BRM25N C: 2 Standard Memory Conversion Kit-4GB (1GB SDRAM-DIMMx4) GP5BRU4GA Standard Memory Conversion Kit-2GB (512GB SDRAM-DIMMx4) GP5BRU2GC Standard Memory Conversion Kit-1GB (256GB SDRAM-DIMMx4) GP5BRU1GF Standard Memory Conversion Kit-512MB(128MB SDRAM-DIMMx4) GP5BRU51K 13

14 Internal HDD / Internal backup device (Standard Drive Cage) Standard Drive Cage 1inch height HDD x 8 SCSI Configuration Hard Disk Drive-9GB(Ultra160, 7,200rpm) D: 3 1"height/Hotplug GP5-HDH9B/GP5BHDH9B Hard Disk Drive-18GB(Ultra160, 7,200rpm) 1"height/Hotplug GP5-HDH88/GP5BHDH88 Hard Disk Drive-9GB(Ultra160,10,000rpm) 1"height/Hotplug GP5-HDH9A/GP5BHDH9A Hard Disk Drive-18GB(Ultra160,10,000rpm) 1"height/Hotplug GP5-HDH87/GP5BHDH87 Hard Disk Drive-36GB(Ultra160,10,000rpm) 1"height/Hotplug GP5-HDH63/GP5BHDH63 Array Configuration 6 Go to SCSI Hard Disk Drive as above E: RAID Card (32MB Cache/Ultra2 Wide SCSI/BBU) GP5-144/GP5B144 RAID Card (64MB Cache/Ultra2 Wide SCSI/BBU) GP RAID Card (32MB Cache/Ultra2 Wide SCSI) GP5-145/GP5B145 RAID Card (32MB Cache/Ultra2 Wide SCSI/BBU) GP5-146/GP5B146 RAID Card (64MB Cache/Ultra160) GP5-148/GP5B148 * GP5-148 RAID Card cannot be installed with other RAID Card * Only one GP5-148 can be installed in a MS610 14

15 Internal backup device Connect one backup device (Wide) F: 4 DLT unit (DLT7000) GP5-DL351/GP5BDL351 Connect secondary backup device (Wide) * Two 5"bays are occupied 6 DAT unit (DDS4) SCSI Card GP5-DT401/GP5BDT401 GP5-127/GP5B127 If mounting two backup devices (Narrow/Wide), SCSI Card (GP5-127) is required for wide connect device. If mounting two backup devices (Wide/Wide), SCSI Card (GP5-127) is required for secondary wide connect device. Tape unit (MLR3) GP5-ML301/GP5BML301 DAT autoloader (DDS4) GP5-DTA102/GP5BDTA102 Occupied two 5" bay slots Max.2 backup devices can be mounted Backup device (Narrow) 4 DLT unit (DLT4000) GP5UDL201/GP5BDL201 * Two 5"bays are occupied DAT unit (DDS3) GP5UDT301/GP5BDT301 Tape unit GP5USL501/GP5BSL501 DAT autoloader (DDS3) GP5-DTA101/GP5BDTA101 Occupied two 5" bay slots (When Drive Cage Conversion Kit is used) Drive Cage Conversion Kit (for CTO only) (HDD Bay: 8bays to 12bays) GP5BBU1 SCSI Configuration G: 3 Hard Disk Drive-9GB(Ultra160, 7,200rpm) 1"height/Hotplug GP5-HDH9B/GP5BHDH9B Hard Disk Drive-18GB(Ultra160, 7,200rpm) 1"height/Hotplug GP5-HDH88/GP5BHDH88 Hard Disk Drive-9GB(Ultra160,10,000rpm) 1"height/Hotplug GP5-HDH9A/GP5BHDH9A Hard Disk Drive-18GB(Ultra160,10,000rpm) 1"height/Hotplug GP5-HDH87/GP5BHDH87 Hard Disk Drive-36GB(Ultra160,10,000rpm) 1"height/Hotplug GP5-HDH63/GP5BHDH63 15

16 Array Configuration H: 6 Go to SCSI Hard Disk Drive as above RAID Card (32MB Cache/Ultra2 Wide SCSI/3ch) GP5-144/GP5B144 RAID Card (64MB Cache/Ultra2 Wide SCSI/BBU) GP RAID Card (32MB Cache/Ultra2 Wide SCSI) GP5-145/GP5B145 RAID Card (32MB Cache/Ultra2 Wide SCSI/BBU) GP5-146/GP5B146 RAID Card (64MB Cache/Ultra160) GP5-148/GP5B148 * GP5-148 RAID Card cannot be installed with other RAID Card * Only one GP5-148 can be installed in a MS610 Internal backup device Backup device (Wide) I: 4 DLT unit (DLT7000) GP5-DL351/GP5BDL351 * Two 5"bays are occupied 6 SCSI Card DAT unit (DDS4) GP5-127/GP5B127 GP5-DT401/GP5BDT401 If mounting two backup devices (Narrow/Wide), SCSI Card (GP5-127) is required for wide connect device. If mounting two backup devices (Wide/Wide), SCSI Card (GP5-127) is required for secondary wide connect device. Max.2 backup devices can be mounted Tape unit (MLR3) GP5-ML301/GP5BML301 DAT autoloader (DDS4) GP5-DTA102/GP5BDTA102 Occupied two 5" bay slots Backup device (Narrow) 4 DLT unit (DLT4000) GP5UDL201/GP5BDL201 * Two 5"bays are occupied DAT unit (DDS3) GP5UDT301/GP5BDT301 Tape unit GP5USL501/GP5BSL501 DAT autoloader (DDS3) GP5-DTA101/GP5BDTA101 Occupied two 5" bay slots 16

17 Others J: 6 LAN Card GP5-183/GP5B183 6 LAN Card GP5-185/GP5B185 6 LAN Card GP5-186/GP5B186 6 LAN Card GP5-187/GP5B187 One PSU can be added 6 Redundant Power Supply Unit GP5UPU161/GP5BUPU161 6 Server Monitor Module GP5USM103/GP5BUSM103 17

18 PRIMERGY MS380 Specification Type Pedestal Rackmount Product ID GP5T38L1A7 GP5T38C1A7 GP5T38B1A7 GP5T38L1R7 GP5T38C1R7 GP5T38B1R7 CPU Pentiumlll Frequency 1GHz 850MHz 800MHz 1GHz 850MHz 800MHz Secondary cache 256KB Number of CPUs 1 (up to 2) Memory Standard 256MB (256MB x 1) Maximum 2GB (512MB x 4) VRAM 2MB VGA chip: ATI RAGEIIC(PCI) Internal Bays 5-inch Three (one occupied by CD-ROM) CD-ROM 40X (IDE) HDD bay 1inch x 8 (Hotplug) Available HDD (Ultra2 Wide) 9.1GB(10000/7200rpm)/18.2GB(10000/7200rpm)/36.4GB(10000rpm) Maximum 218.4GB (36.4GB x 6) Expansion slot PCI32bit 33MHz x5 SCSI Interface Ultra2 Wide SCSI x2, Narrow x1 RAID controller Option Network LAN(10/100 base TX) x 1 (onboard) Dimension (mm) 307(W)x700(D)x474(H) 483(W)x680(D)x307(H) Rackmount7U Weight 55kg (max.) Power consumption 490W (max.) Power supply One standard units (up to three for redundant) Mounting additional memory The mother board has four slots for RAM modules (including base memory), install RAM modules in slot number order. Mounting internal SCSI devices MS380 has eight HDD bays and 36.4GB/18.2GB/9.1GB HDD (1"height) can be mounted. Up to six HDDs with 10000rpm (GP5-HDH9A/GP5-HDH87/GP5-HDH63) can be mounted. (10000rpm HDD cannot be used with 7200rpm HDD) SCSI Card (GP5-127) is required if DLT unit (GP5-DL351), DAT unit (GP5-DT401), Tape unit (GP5-ML301) or DAT autoloader (GP5-DTA102) is installed Only one DDS-4 (GP5-DT401) can be mounted in the lowest 5inch bay. 5-inch bay installation Bay1: Used for CD-ROM (IDE) (Support as standard) Bay2: SCSI ID = 4 (fixed) Tape Unit(MLR3, SLR5) can be installed in this bay Bay3: SCSI ID = 5 (fixed) DAT(DDS4, DDS3), DAT Autoloader(DDS4, DDS3), Tape Unit(MLR3, SLR5), DLT Unit(DLT7000, DLT4000) can be installed in this bay Note: A DAT Autoloader, DLT unit installed in 5-inch bay 3 will also occupy bay2 because of it's height. A separate SCSI Card is required when installing a Tape Unit (MLR3), DAT(DDS4), DAT Autoloader(DDS4) or DLT(DLT7000) in a 5-inch bay. See diagram below. Connection of internal HDD and internal backup devices Mother Board of MS380 Onboard SCSI Narrow Wide A Wide B For backup device (Narrow) For HDD For HDD 18

19 Internal HDD Internal backup device (Max.2) Connection Pattern One device is connected Two devices are connected Connection SCSI Host Cable Internal HDD Narrow Wide Narrow device Wide device Narrow device and Interface connect connect x 2 x 2 Wide device device*1 device*2 1)9GB,7,200rpm Cable(X2) 2)18GB,7,200rpm Wide-1 Narrow device: Ultra2 Wide Onboard SCSI (Standard 3)9GB,10,000rpm Narrow-1,2 SCSI Card Onboard SCSI Configuration equipment) 4)18GB,10,000rpm Onboard SCSI Card (GP5-127) SCSI(Narrow) 5)36GB,10,000rpm SCSI(Narrow) (GP5-127) Onboard connection SCSI(Narrow) Wide-2 Wide device: RAID Card Cable(X2) 1)9GB,7,200rpm Daisy chain SCSI Card SCSI Card(GP5-127) Array Configuration Ultra2 Wide GP5-144/145/ (Standard 2)18GB,7,200rpm connection (GP5-127)*3 146 (Ch0) equipment) 3)9GB,10,000rpm 4)18GB,10,000rpm 5)36GB,10,000rpm *1 Narrow connect devices: GP5UDL201/GP5UDT301/GP5USL501/GP5-DTA101 *2 Wide connect devices: GP5-DT401/GP5-DTA102/GP5-ML301/GP5-DL351(SCSI Cable is standard equipment with all Wide connect devices) *3 Daisy chain is not available for connection of a Wide SCSI connection device to SCSI Card (GP5-127) *4 SCSI Cable is standard equipment (Narrow: Main unit/wide: Backup device) Connection Table PRMIERGY MS380 GP5T38L1A7 1CPU/Pedestal Type 1CPU (Pentium(R)lll 1GHz), Memory:256MB(ECC), HDD:Option GP5T38L1R7 1CPU/Rackmount Type 1CPU (Pentium(R)lll 1GHz), Memory:256MB(ECC), HDD:Option GP5T38C1A7 1CPU/Pedestal Type 1CPU (Pentium(R)lll 850MHz), Memory:256MB(ECC), HDD:Option (Pedestal type ) GP5T38C1R7 1CPU/Rackmount Type 1CPU (Pentium(R)lll 850MHz), Memory:256MB(ECC), HDD:Option GP5T38B1A7 1CPU/Pedestal Type 1CPU (Pentium(R)lll 800MHz), Memory:256MB(ECC), HDD:Option (Rackmount type) GP5T38B1R7 1CPU/Rackmount Type 1CPU(Pentium(R)lll 800MHz), Memory:256MB(ECC), HDD:Option <Items> CPU Field Upgrade : GoTo A Memory addition : GoTo B Internal Hard Disk Drive connection 1. SCSI connection GoTo C 2. Array connection GoTo D Internal Backup devices Others (NIC etc.) GoTo E GoTo F CPU Max : 2CPUs CPU Field Upgrade Kit-79 (Pentium III-1GHz (256KB) x1) A: 1 GP5-FG20L/GP5BFG20L CPU Field Upgrade Kit-63 (Pentium III-850MHz (256KB) x1) GP5-FG20C/GP5BFG20C CPU Field Upgrade Kit-62 (Pentium III-800MHz (256KB) x1) GP5-FG20B/GP5BFG20B Memory Max.2GB B: 2 Additional Memory - 64MB (64MB SDRAM-DIMM x1) Standard memory : 256MB (256MB SDRAM-DIMM x1) GP5-RM64F/GP5BRM64F Additional Memory -128MB (128MB SDRAM-DIMM x1) GP5-RM12F/GP5BRM12F Additional Memory - 256MB (256MB SDRAM-DIMM x1) GP5-RM25F/GP5BRM25F Additional Memory MB( 512MB SDRAM-DIMMx1) GP5-RM51F/GP5BRM51F 19

20 Standard Memory Conversion 2 Standard Memory Conversion Kit-512MB ( 512MB SDRAM-DIMMx1) GP5BRU51F Internal Hard Disk (1)Disk Addition / Duplexing Hard Disk Drive - 9GB (Ultra2 Wide.10,000rpm) : max 6 C: 3 (Hot Plug) Up to 8 disks GP5-HDH9A/GP5BHDH9A Cannot be used with 7200rpm HDD Up to six 10000rpm HDD Hard Disk Drive -18GB (Ultra2 Wide.10,000rpm) : max 6 can be mounted in MS380 (Hot Plug) GP5-HDH87/GP5BHDH87 Cannot be used with 7200rpm HDD Hard Disk Drive - 36GB (Ultra2 Wide.10,000rpm) : max 6 (Hot Plug) GP5-HDH63/GP5BHDH63 Cannot be used with 7200rpm HDD Hard Disk Drive - 9GB (Ultra2 Wide.7,200rpm) (Hot Plug) GP5-HDH96/GP5BHDH96 Hard Disk Drive -18GB (Ultra2 Wide.7,200rpm) (Hot Plug) GP5-HDH83/GP5BHDH83 Up to six 10000rpm HDD (2)Internal Disk Array can be mounted in MS380 Hard Disk Drive - 9GB (Ultra2 Wide.10,000rpm) : max 6 D: 6 RAID Card (Cache : 32MB, Ultra2 Wide SCSI, BBU) (Hot Plug) GP5-144/GP5B144 GP5-HDH9A/GP5BHDH9A Cannot be used with 7200rpm HDD RAID Card (Cache :64MB, Ultra2 Wide SCSI), BBU Hard Disk Drive -18GB (Ultra2 Wide.10,000rpm) : max 6 GP (Hot Plug) GP5-HDH87/GP5BHDH87 Cannot be used with 7200rpm HDD RAID Card (Cache :16MB, Ultra2 Wide SCSI) GP5-145/GP5B145 Hard Disk Drive - 36GB (Ultra2 Wide.10,000rpm) : max 6 (Hot Plug) GP5-HDH63/GP5BHDH63 RAID Card (Cache :16MB, Ultra2 Wide SCSI, BBU) Cannot be used with 7200rpm HDD GP5-146/GP5B146 Hard Disk Drive - 9GB (Ultra2 Wide.7,200rpm) (Hot Plug) GP5-HDH96/GP5BHDH96 Hard Disk Drive -18GB (Ultra2 Wide.7,200rpm) (Hot Plug) GP5-HDH83/GP5BHDH83 20

21 Internal Backup Devices Backup device (Wide) E: 6 DLT unit (DLT7000)*(Occupied two 5" bay slots) GP5-DL351/GP5BDL351 SCSI Card GP5-127/GP5B127 Tape unit (MLR3) GP5-ML301/GP5BML301 Max.2 backup devices can be mounted DAT unit (DDS4) GP5-DT401/GP5BDT401 DAT autoloader (DDS4) GP5-DTA102/GP5BDTA102 Occupied two 5" bay slots Backup device Narrow 4 DLT unit (DLT4000)(Occupied two 5" bay slots) GP5UDL201/GP5BDL201 DAT unit (DDS3) GP5UDT301/GP5BDT301 Tape unit (SLR5) GP5USL501/GP5BSL501 DAT autoloader (DDS3) GP5-DTA101/GP5BDTA101 Occupied two 5" bay slots Others F: 6 LAN Card GP5-183/GP5B183 6 LAN Card GP5-185/GP5B185 6 LAN Card GP5-187/GP5B187 8 Redundant Power Supply Unit GP5UPU131/GP5BUPU131 6 Server Monitor Module GP5USM103/GP5BUSM103 *NOTE : 2 PSUs are required as standard if GP5-DL351 is installed Maximum 3PSUs can be installed in MS

22 PRIMERGY ES320 Specification Type Pedestal Rackmount Product ID GP5T3CL1A GP5T3CE1A GP5T3CB1A GP5T3CL1R GP5T3CE1R GP5T3CB1R CPU Pentiumlll Frequency 1BGHz 933MHz 800EBMHz 1BGHz 933MHz 800EBMHz Secondary cache 256KB Number of CPUs 1 (up to 2) Memory Standard 256MB (256MB x 1) Maximum 4GB (1GB x 4) VRAM 4MB VGA chip: ATI RAGE XL(PCI) Internal Bays 5-inch Three (one occupied by CD-ROM) CD-ROM 40X (IDE) HDD bay 1inch x 5 (Hotplug) Available HDD (Ultra160) 9.1GB(10000rpm)/18.2GB(10000rpm)/36.4GB(10000rpm) Available HDD (Ultra2 Wide) 9.1GB(7200rpm)/18.2GB(7200rpm) Maximum 182.0GB (36.4GB x 5) Expansion slot PCI64bit 33MHz x4, PCI32bit 33MHz x2 SCSI Interface Ultra160 x1, Ultra160 or Narrow x1 RAID controller Option Network LAN(10/100 base TX) x 1 (onboard) Dimension (mm) 174(W)x615(D)x449(H) 482(W)x565(D)x174(H) Rackmount4U Weight 32kg 35kg Power consumption 340W (max.) Power supply One standard units (up to two for redundant) Mounting additional memory The mother board has four slots for RAM modules (including base memory), install RAM modules in slot number order. Mounting internal SCSI devices ES320 has five HDD bays and 36.4GB/18.2GB/9.1GB HDD (1"height) can be mounted. SCSI Card (GP5-127) is required if DLT unit (GP5-DL351), DAT unit (GP5-DT401), Tape unit (GP5-ML301) or DAT autoloader (GP5-DTA102) is installed When DLT unit (GP5UDL201) is installed, DLT Enclosure (GP5-BC2) is required. 5-inch bay installation Bay1: Used for CD-ROM (IDE) (Support as standard) Bay2: SCSI ID = 4~6 (Setting on the device side), SCSI ID = 4 (CTO) DAT (DDS4, DDS3), Tape Unit(MLR3, SLR5) can be installed in this bay Bay3: SCSI ID = 4~6 (Setting on the device side), SCSI ID = 5 (CTO) DAT(DDS4, DDS3), DAT Autoloader(DDS4, DDS3), DLT Unit(DLT4000) can be installed in this bay Note: SCSI IDs of the devices installed in bay2 and bay3 must be different. Even if bays 2 or 3 are not used, the appropriate Narrow SCSI Cable must be connected. A DAT Autoloader, DLT unit is installed in bay3 and also occupies bay2. When installing a Narrow SCSI device in a system already containing a Wide SCSI devices, connect the Narrow device to the Narrow Onboard channel and reconnect the Wide device to a separate SCSI Card. Connection of internal HDD and internal backup devices Mother Board of ES320 Onboard SCSI Narrow Wide B For backup device (Narrow) For Backup device (Wide) Select either of the SCSI channel Wide A For HDD 22

23 Internal HDD Internal backup device (Max.2) Connection Pattern One device is connected Two devices are connected Connection SCSI Host Cable Internal HDD Narrow Wide Narrow device Wide device Narrow device and Interface connect connect x 2 x 2 Wide device device*1 device*2 1)9GB,7,200rpm Wide-1 SCSI Cable 2)18GB,7,200rpm Onboard SCSI Narrow device: Ultra160 Onboard SCSI (Standard 3)9GB,10,000rpm Narrow-1,2 Wide-2 Onboard SCSI Configuration equipment) 4)18GB,10,000rpm Onboard Onboard SCSI Card SCSI(Narrow) 5)36GB,10,000rpm SCSI(Narrow) SCSI (Wide) Onboard (GP5-127) 1)9GB,7,200rpm connection SCSI(Narrow) Wide-1 Wide device: RAID Card SCSI Cable 2)18GB,7,200rpm Daisy chain Onboard SCSI SCSI Card(GP5-127) Array Configuration Ultra2 Wide GP5-144/146 (Ch0) (Standard 3)9GB,10,000rpm connection Wide-2 Ultra160 GP5-148(Ch0) equipment) 4)18GB,10,000rpm SCSI Card 5)36GB,10,000rpm (GP5-127) *1 Narrow connect devices: GP5UDL201/GP5UDT301/GP5USL501/GP5-DTA101 *2 Wide connect devices: GP5-DT401/GP5-DTA102/GP5-ML301/GP5-DL351(SCSI Cable is standard equipment with all Wide connect devices) *3 Daisy chain is not available for connection of a Wide SCSI connection device to SCSI Card (GP5-127) *4 SCSI Cable is standard equipment (Narrow: Main unit/wide: Backup device) Connection Table PRMIERGY ES320 GP5T3CL1A 1CPU/Pedestal Type 1CPU (Pentium(R)lll 1BGHz), Memory:256MB(ECC), HDD:Option GP5T3CL1R 1CPU/Rackmount Type 1CPU (Pentium(R)lll 1BGHz), Memory:256MB(ECC), HDD:Option GP5T3CE1A 1CPU/Pedestal Type 1CPU (Pentium(R)lll 933MHz), Memory:256MB(ECC), HDD:Option GP5T3CE1R 1CPU/Rackmount Type 1CPU (Pentium(R)lll 933MHz), Memory:256MB(ECC), HDD:Option GP5T3CB1A 1CPU/Pedestal Type 1CPU (Pentium(R)lll 800EBMHz), Memory:256MB(ECC), HDD:Option GP5T3CB1R 1CPU/Rackmount Type 1CPU(Pentium(R)lll 800EBMHz), Memory:256MB(ECC), HDD:Option <Items> (Pedestal type ) CPU Field Upgrade : GoTo A Memory addition : GoTo B (Rackmount type) Internal Hard Disk Drive connection 1. SCSI connection GoTo C 2. Array connection GoTo D Internal Backup devices Others (NIC etc.) GoTo E GoTo F CPU Max : 2CPUs CPU Field Upgrade Kit-81 (Pentium III-1BGHz (256KB) x1) A: 1 GP5-FG21L/GP5BFG21L CPU Field Upgrade Kit-80 (Pentium III-933MHz (256KB) x1) GP5-FG21E/GP5BFG21E CPU Field Upgrade Kit-71 (Pentium III-800EBMHz (256KB) x1) GP5-FG22B/GP5BFG22B Memory Max.4GB B: 2 Additional Memory - 128MB (128MB SDRAM-DIMM x1) Standard memory : 256MB (256MB SDRAM-DIMM x1) GP5-RM12M/GP5BRM12M Additional Memory - 256MB (256MB SDRAM-DIMM x1) GP5-RM25M/GP5BRM25M Additional Memory - 512MB (512MB SDRAM-DIMM x1) GP5-RM51M/GP5BRM51M Additional Memory - 1GB (1GB SDRAM-DIMM x1) GP5-RM1M/GP5BRM1M 23

24 Standard Memory Conversion 2 Standard Memory Conversion Kit-1GB (1GB SDRAM-DIMMx1) GP5BRU1GE Standard Memory Conversion Kit-512MB (512MB SDRAM-DIMMx1) GP5BRU51J Internal Hard Disk (1)Disk Addition / Duplexing C: 3 Hard Disk Drive - 9GB (Ultra160,10,000rpm) (Hot Plug) Up to 5 disks GP5-HDH9D/GP5BHDH9D Hard Disk Drive -18GB (Ultra160, 10,000rpm) (Hot Plug) GP5-HDH8A/GP5BHDH8A Hard Disk Drive - 36GB (Ultra160, 10,000rpm) (Hot Plug) GP5-HDH63/GP5BHDH63 Hard Disk Drive - 9GB (Ultra2 Wide, 7,200rpm) (Hot Plug) GP5-HDH9C/GP5BHDH9C Hard Disk Drive -18GB (Ultra2 Wide, 7,200rpm) (Hot Plug) GP5-HDH89/GP5BHDH89 (2)Internal Disk Array D: 6 RAID Card (Cache : 8MB, Ultra2 Wide SCSI) Hard Disk Drive - 9GB (Ultra160,10,000rpm) (Hot Plug) GP5-143/GP5B143 GP5-HDH9D/GP5BHDH9D RAID Card (Cache : 32MB, Ultra2 Wide SCSI, BBU) GP5-144/GP5B144 Hard Disk Drive -18GB (Ultra160, 10,000rpm) (Hot Plug) GP5-HDH8A/GP5BHDH8A RAID Card (Cache :16MB, Ultra2 Wide SCSI) GP5-145/GP5B145 Hard Disk Drive - 36GB (Ultra160, 10,000rpm) (Hot Plug) GP5-HDH63/GP5BHDH63 RAID Card (Cache :16MB, Ultra2 Wide SCSI, BBU) GP5-146/GP5B146 Hard Disk Drive - 9GB (Ultra2 Wide, 7,200rpm) (Hot Plug) GP5-HDH9C/GP5BHDH9C RAID Card (Cache :64MB, Ultra160) GP5-148/GP5B148 * GP5-148 RAID Card cannot be installed with other RAID Card * Only one GP5-148 can be installed in a ES320 Hard Disk Drive -18GB (Ultra2 Wide, 7,200rpm) (Hot Plug) GP5-HDH89/GP5BHDH89 24

25 Internal Backup Devices Backup device (Wide) E: 4 Tape unit (MLR3) Onboard SCSI Controller GP5-ML301/GP5BML301 6 DAT unit (DDS4) GP5-DT401/GP5BDT401 SCSI Card GP5-127/GP5B127 Max.2 backup devices can be mounted DAT autoloader (DDS4) GP5-DTA102/GP5BDTA102 Occupied two 5" bay slots Backup Device (Narrow) 4 DLT unit (DLT4000)(Occupied two 5" bay slots) Onboard SCSI Controller GP5UDL201/GP5BDL201 *DLT Enclosure (GP5-BC2) is required to install DLT4000 DAT unit (DDS3) GP5UDT301/GP5BDT301 Tape unit (SLR5) GP5USL501/GP5BSL501 DAT autoloader (DDS3) GP5-DTA101/GP5BDTA101 Occupied two 5" bay slots Others F: 6 LAN Card GP5-183/GP5B183 6 LAN Card GP5-185/GP5B185 6 LAN Card GP5-186/GP5B186 6 LAN Card GP5-187/GP5B187 8 Redundant Power Supply Unit GP5UPU151/GP5BUPU151 6 Server Monitor Module GP5USM103/GP5BUSM103 25

26 PRIMERGY ES280 Specification Type Pedestal Rackmount Product ID GP5T28C1A7 GP5T28B1A7 GP5T28C1R7 GP5T28B1R7 CPU Pentiumlll Frequency 850MHz 800MHz 850MHz 800MHz Secondary cache 256KB Number of CPUs 1 (up to 2) Memory Standard 128MB (128MB x 1) Maximum 1GB (256MB x 4) VRAM 2MB VGA chip: ATI RAGEIIC(AGP) Internal Bays 5-inch Three (one occupied by CD-ROM) CD-ROM 40X (IDE) HDD bay 1inch x 4 (3Hotplug) Available HDD (Ultra2 Wide) 9.1GB(7200rpm)/18.2GB(7200rpm) Maximum 72.8GB(18.4GB x4) Expansion slot PCI32bit 33MHz x3 SCSI Interface Ultra Wide SCSI x1, Narrow x1 RAID controller Option Network LAN(10/100 base TX) x 1 (onboard) Dimension (mm) 219(W)x549(D)x456(H) 483(W)x602(D)x265(H) Rackmount6U Weight 25kg (max.) 35kg (max.) Power consumption 250W (max.) Power supply One (No Redundant) Mounting additional memory The mother board has four slots for RAM modules (including base memory), install RAM modules in slot number order. Mounting internal SCSI devices ES280 have four HDD bays (3hotplug and 1non Hotplug) 9.1GB/18.2GB HDD (1"height) can be mounted. SCSI Card (GP5-125) is required if DAT unit (GP5-DT401), Tape unit (GP5-ML301) is installed Only one DDS-4 (GP5-DT401) can be mounted in the lowest 5inch bay. 5-inch bay installation Bay1: Used for CD-ROM (IDE) (Support as standard) Bay2: SCSI ID = 4 (fixed) Tape Unit(MLR3, SLR5) can be installed in this bay Bay3: SCSI ID = 5 (fixed) DAT(DDS4, DDS3), Tape Unit(MLR3, SLR5) can be installed in this bay Note: Although it is physically possible to install two DAT backup devices in these 5-inch bays, only one DAT backup device should be installed in bay3, because of the heat management requirements. Even if bay 2 or 3 is not used, the appropriate Narrow SCSI Cable must be connected. Connection of internal HDD and internal backup devices Mother Board of ES280 Onboard SCSI Narrow Wide For backup device (Narrow) For HDD 26

27 Internal HDD Internal backup device (Max:2) Connection Pattern One device is connected Two devices are connected Connection Interface Narrow connect Wide connect Narrow device and Host Internal HDD device *1 device *2 Narrow device x 2 Wide device x 2 Wide device SCSI Ultra Wide Onboard SCSI (Wide) 1)9GB,7,200rpm Narrow device: Configuration SCSI SCSI Cable (GP5-843) 2)18GB,7,200rpm Onboard SCSI Onboard SCSI (Narrow) SCSI Card (Narrow) Onboard SCSI (Narrow) SCSI Card (GP5-125 *3) SCSI Cable(Std.) (GP5-125 *3) Daisy chain with primary (SCSI Card is Wide device: Array Ultra2 Wide RAID Card 1)9GB,7,200rpm connected device required per device) SCSI Card Configuration SCSI (GP5-143) 2)18GB,7,200rpm (GP5-125) SCSI Cable(GP5-843) *1 Narrow connect devices: GP5UDT301/GP5USL501 *2 Wide connect devices: GP5-DT401/GP5-ML301(SCSI Cable is standard equipment with all Wide connect devices) *3 Daisy chain is not available for connection of a Wide SCSI device to SCSI Card(GP5-127) *4 SCSI Cable is standard equipment (Narrow: Main unit/wide: Backup device) Connection Table GP5T28C1A7 1CPU/Pedestal Type 1CPU (Pentium(R)lll 850MHz), Memory:128MB(ECC), HDD:Option PRIMERGY ES280 GP5T28C1R7 1CPU/Rackmount Type 1CPU (Pentium(R)lll 850MHz), Memory:128MB(ECC), HDD:Option GP5T28B1A7 1CPU/Pedestal Type 1CPU (Pentium(R)lll 800MHz), Memory:128MB(ECC), HDD:Option GP5T28B1R7 1CPU/Rackmount Type 1CPU (Pentium(R)lll 800MHz), Memory:128MB(ECC), HDD:Option <Items> CPU Field Upgrade : GoTo A Memory addition : GoTo B Internal Hard Disk Drive connection (Pedestal type ) 1. SCSI connection GoTo C 2. Array connection GoTo D (Rackmount type) Internal Backup devices GoTo E Others (NIC etc.) GoTo F CPU Max : 2CPUs A: 1 CPU Field Upgrade Kit-63 (Pentium III-850MHz (256KB) x1) GP5-FG20C/GP5BFG20C CPU Field Upgrade Kit-62 (Pentium III-800MHz (256KB) x1) GP5-FG20B/GP5BFG20B Memory Max.1GB B: 2 Additional Memory - 64MB (64MB SDRAM-DIMMx1) Standard : 128MB (128MB SDRAM-DIMMx1) GP5-RM64F/GP5BRM64F Additional Memory - 128MB (128MB SDRAM-DIMMx1) GP5-RM12F/GP5BRM12F Additional Memory - 256MB (256MB SDRAM-DIMMx1) GP5-RM25F/GP5BRM25F Standard Memory Conversion Option Standard Memory Conversion Kit-256MB 2 (256MB SDRAM-DIMMx1) GP5BRU25E Internal Hard Disk Total 4 disks(3hot Plug and1non-hot Plug)Can be installed. (1)Disk Addition to Hot Plug bays (Max. 3 disks) C: 3 Hard Disk Drive - 9GB (Ultra Wide, 7,200rpm)(Hot Plug) GP5-HDH96/GP5BHDH96 Hard Disk Drive -18GB (Ultra Wide, 7,200rpm)(Hot Plug) GP5-HDH83/GP5BHDH83 27

28 (2)Internal Disk Array (Maximum 3Hot Plug disks can be installed) D: 6 Hard Disk Drive - 9GB (Ultra Wide.7,200rpm)(Hot Plug) RAIDCard (Cache :16MB) GP5-HDH96/GP5BHDH96 GP5U141/GP5BU141 GP5U831/GP5B831 SCSICable (Intl.) Hard Disk Drive -18GB (Ultra Wide.7,200rpm)(Hot Plug) RAIDCard (Cache : 8MB Internal Hard disk only) GP5-HDH83/GP5BHDH83 GP5-143/GP5B143 (3)Disk Addition to a non-hot Plug bay only one disc can be installed 3 Hard Disk Drive - 9GB (7,200rpm) (non-hot Plug) GP5-HD9G3/GP5BHD9G3 Internal Backup Devices Hard Disk Drive -18GB (7,200rpm) (non-hot Plug) GP5-HD8G1/GP5BHD8G1 Backup devices (Wide) E: 6 Tape unit (MLR3) GP5-ML301/GP5BML301 SCSI Card GP5-125/GP5B125 DAT unit (DDS4) GP5-DT401/GP5BDT401 Backup devices (Narrow) 4 DAT unit (DDS3) Onboard SCSI Controller GP5UDT301/GP5BDT301 Others Tape unit (SLR5) GP5USL501/GP5BSL501 F: 6 LAN Card GP5-183/GP5B183 6 LAN Card GP5-185/GP5B185 6 LAN Card GP5-187/GP5B187 6 Server Monitor Module GP5USM103/GP5BUSM103 28

29 PRIMERGY ES210 Specification Type Pedestal Product ID GP5T2BL1A2 GP5T2BC1A2 GP5T2BB1A2 CPU Pentiumlll Frequency 1GHz 850MHz 800MHz Secondary cache 256KB Number of CPUs 1 (up to 2) Memory Standard 128MB (128MB x 1) Maximum 1GB (256MB x 4) VRAM 4MB VGA chip: ATI RAGE XL(AGP) Internal Bays 5-inch Three (one occupied by CD-ROM) CD-ROM 40X (IDE) HDD bay 1inch x 4 (Non Hotplug) Available HDD (Ultra2 Wide) 9.1GB(10000/7200rpm)/18.2GB(10000/7200rpm)/36.4GB(10000rpm) Maximum 127.4GB(36.4GB x GB x1) Expansion slot PCI32bit 33MHz x3 SCSI Interface Ultra Wide SCSI x1, Narrow x1 RAID controller Option Network LAN(10/100 base TX) x 1 (onboard) Dimension (mm) 210(W)x473(D)x427(H) Weight 21kg (max.) Power consumption 220W (max.) Power supply One (No Redundant) Mounting additional memory The mother board has four slots for RAM modules (including base memory), install RAM modules in slot number order. Mounting internal SCSI devices ES210 have four HDD bays (three HDD bays and one 5inch bay) 9GB/18.2GB/36GB HDD (1"height) can be mounted. *10000rpm HDD cannot be mounted in 5inch bay HDD can be connected to Onboard UltraWide SCSI. (SCSI Cable is required) SCSI Card (GP5-127) is required for Ultra2 Wide configuration. SCSI Card (GP5-127) is required to mount DDS4 backup device. 29

30 5-inch bay installation Bay1: Used for CD-ROM (IDE) (Support as standard) Bay2: SCSI ID = 4~6 (Setting on the device side), SCSI ID = 4 (CTO) DAT (DDS4, DDS3) can be installed in this bay Bay3: SCSI ID = 4~6 (Setting on the device side), SCSI ID = 5 (CTO) DAT(DDS4), HDD (Ultra2 Wide Non Hotplug) can be installed in this bay Connection of internal HDD and internal backup devices Mother Board of ES210 There are two SCSI channels and two EIDE channels on the Motherboard Onboard IDE Controller Onboard SCSI Controller Secondary EIDE Primary EIDE Narrow Wide For CD-ROM For HDD For backup device (Narrow) For HDD Internal HDD Internal backup device (Max:2) Connection Pattern One device is connected Two devices are connected Connection Interface Narrow connect Wide connect Narrow device and Host Internal HDD device *1 device *2 Narrow device x 2 Wide device x 2 Wide device SCSI Ultra Wide Onboard SCSI (Wide) 1)9GB,7,200rpm Narrow device: Configuration SCSI SCSI Cable (GP5-843) 2)18GB,7,200rpm 3)9GB,10,000rpm Onboard SCSI Onboard SCSI SCSI Ultra2 Wide SCSI Card(GP5-127) 4)18GB,10,000rpm (Narrow) SCSI Card (Narrow) Configuration SCSI SCSI Cable(GP5-843) 5)36GB,10,000rpm Onboard SCSI (Narrow) SCSI Card Daisy chain (GP5-127 *3) SCSI Cable(Std.) IDE IDE Onboard Primary IDE 1)30GB, 5400rpm (GP5-127 *3) with primary (SCSI Card is Configuration UltraDMA/33 connected device required per device) Wide device: Array Ultra2 Wide RAID Card 1)9GB,7,200rpm SCSI Card Configuration SCSI (GP5-143) 2)18GB,7,200rpm (GP5-127) SCSI Cable(GP5-843) 3)9GB,10,000rpm 4)18GB,10,000rpm 5)36GB,10,000rpm *1 Narrow connect devices: GP5UDT301 *2 Wide connect devices: GP5-DT401(SCSI Cable is standard equipment with all Wide connect devices) *3 Daisy chain is not available for connection of a Wide SCSI device to SCSI Card(GP5-127) *4 SCSI Cable is standard equipment (Narrow: Main unit/wide: Backup device) Connection Table GP5T2BL1A2: GP5T2BC1A2: GP5T2BB1A2: 1CPU(Pentium(R)lll1GHz)/Pedestal Type 1CPU(Pentium(R)lll850MHz)/Pedestal Type 1CPU(Pentium(R)lll800MHz)/Pedestal Type <Items> CPU Field Upgrade : Memory addition : Standard memory conversion : SCSI configuration Internal Hard Disk Drive (Ultra Wide) : Internal Hard Disk Drive (Ultra2 Wide) : Internal backup device : IDE/Array configuration Internal Hard Disk Drive (IDE) : Internal Hard Disk Drive (Array) : Internal backup device : Others (NIC, PSU, etc.) : Go to A Go to B Go to C Go to D Go to E Go to F Go to G Go to H Go to I Go to J 30

31 A: CPU Max : 2CPUs 1 CPU Field Upgrade Kit-79(Pentiumlll 1GHz(256KB)x1) GP5-FG20L/GP5BFG20L CPU Field Upgrade Kit-63(Pentiumlll 850MHz(256KB)x1) GP5-FG20C/GP5BFG20C CPU Field Upgrade Kit-62(Pentiumlll 800MHz(256KB)x1) GP5-FG20B/GP5BFG20B Memory Max:1GB(256MB SDRAM-DIMM x 4) B: 2 Additional Memory-64MB (64MB SDRAM-DIMMx1) Standard:128MB (128MB SDRAM-DIMMx1) GP5-RM64H/GP5BRM64H Additional Memory-128MB (128MB SDRAM-DIMMx1) GP5-RM12H/GP5BRM12H Additional Memory-256MB (256MB SDRAM-DIMMx1) GP5-RM25H/GP5BRM25H Standard Memory conversion option C: 2 Standard Memory Conversion Kit-256MB (256MB SDRAM-DIMMx1) GP5BRU25D Internal HDD / Internal backup device (SCSI Configuration) Ultra Wide Max: 4 HDDs D: 3 Hard Disk Drive-9GB(Ultra2 Wide SCSI,7,200rpm) Onboard SCSI GP5-HD9G3/GP5BHD9G3 (For HDD bay:up to 3HDDs can be mounted) SCSI Cable GP5-HD9G3C /GP5BHD9G3C (For 5"bay:Only one can be mounted) GP5-843/GP5B843 Ultra2 Wide E: 6 Hard Disk Drive-18GB(Ultra2 Wide SCSI,7,200rpm) GP5-HD8G1/GP5BHD8G1 (For HDD bay:up to 3HDDs can be mounted) SCSI Card GP5-HD8G1C/GP5BHD8G1C(For 5"bay:Only one can be mounted) GP5-127/GP5B127 Hard Disk Drive-9GB(Ultra2 Wide SCSI,10,000rpm) GP5-HD9G4/GP5BHD9G4 (For HDD bay:up to 3HDDs can be mounted) Hard Disk Drive-18GB(Ultra2 Wide SCSI,10,000rpm) GP5-HD8G2/GP5BHD8G2 (For HDD bay:up to 3HDDs can be mounted) Hard Disk Drive-36GB(Ultra2 Wide SCSI,10,000rpm) GP5-HD6G1/GP5BHD6G1 (For HDD bay:up to 3HDDs can be mounted) Backup device (Narrow) F: 4 DAT unit(dds3) Onboard SCSI Controller GP5UDT301/GP5BDT301 Max.2 backup devices can be mounted Backup device (Wide) 6 DAT unit(dds4) GP5-DT401/GP5BDT401 SCSI Card GP5-127/GP5B127 SCSI Cable is supplied with wide backup devices. 31

32 (IDE configuration) Max:2 IDE Disk can be mounted G: 3 Hard Disk Drive-30GB(Ultra33/DMA,5,400rpm) GP5-HD3E2/GP5BHD3E2 (Array configuration) H: 6 Go to SCSI Hard Disk Drive as above RAID Card (8MB Cache, Ultra2 Wide SCSI, SCSI Cable Only for internal HDD connection) GP5-843/GP5B843 GP5-143/GP5B143 Backup device (Narrow) I: 4 DAT unit (DDS3) Onboard SCSI Controller GP5UDT301/GP5BDT301 SCSI Card (GP5-127/GP5B127) is required for mounting Wide connect backup device. Max.2 backup devices can be mounted Backup device (Wide) 6 DAT unit (DDS4) GP5-DT401/GP5BDT401 SCSI Card SCSI Cable is a standard equipment of backup device GP5-127/GP5B127 Others J: 6 LAN Card GP5-183/GP5B183 6 LAN Card GP5-185/GP5B185 6 LAN Card GP5-186/GP5B186 6 LAN Card GP5-187/GP5B187 6 Server Monitor Module GP5USM103/GP5BUSM103 32

33 PRIMERGY ES200 Specification Type Pedestal Product ID GP5T2AB1A3 GP5T2AK1A3 CPU Frequency Pentiumlll 800MHz Celeron 633MHz Secondary cache 256KB 128KB Number of CPUs 1 Memory Standard 128MB(128MB x1) Maximum 768MB(256MB x3) Internal Bays 5-inch Three (One occupied by CD-ROM) CD-ROM 40X (IDE) HDD bay 1inch x 4 (Non Hotplug) Available HDD (Ultra2 Wide) 9.1GB(10000/7200rpm)/18.2GB(10000/7200rpm)/36.4GB(10000rpm) Maximum 127.4GB(36.4GB x GB x1) Expansion slot PCI32bit 33MHz x4 SCSI Interface Option RAID controller Option Network LAN(10/100 base TX) x 1 (onboard) Dimension (mm) 210(W)x473(D)x427(H) Weight 21kg (max.) Power consumption 170W (max.) Power supply One (No Redundant) Mounting additional memory The mother board has three slots for RAM modules (including base memory), install RAM modules in slot number order. 33

34 Mounting internal SCSI devices ES200 have four HDD bays (three HDD bays and one 5inch bay) 9GB/18.2/36GB HDD (1"height) can be mounted. *10000rpm HDD cannot be mounted in 5inch bay SCSI Card (GP5-126) is required to mount HDD. The SCSI Card (GP5-126) is also used for connection to Narrow connect backup device (GP5UDT301/GP5USL501) with SCSI Cable (.GP5-841) SCSI Card (GP5-127) is required to mount Wide connect backup device (GP5-DT401/GP5-ML301). 5-inch bay installation Bay1: Used for CD-ROM (IDE) (Support as standard) Bay2: SCSI ID = 4~6 (Setting on the device side), SCSI ID = 4 (CTO) DAT (DDS4, DDS3), Tape Unit (MLR3, SLR5) can be installed in this bay Bay3: SCSI ID = 4~6 (Setting on the device side), SCSI ID = 5 (CTO) DAT (DDS4), Tape Unit (MLR3, SLR5) can be installed in this bay Connection of internal HDD and internal backup devices Mother Board of ES200 There are two EIDE channels on Motherboard Onboard IDE Controller Secondary EIDE Primary EIDE For CD-ROM For HDD Internal HDD Internal backup device (Max:2) Connection Pattern One device is connected Two devices are connected Internal HDD Interface Narrow connect Wide connect Narrow device and Host Internal HDD device *1 device *2 Narrow device x 2 Wide device x 2 Wide device 1)9GB,7,200rpm SCSI Card(GP5-126) SCSI Card(GP5-126) Narrow device: SCSI Ultra2 Wide SCSI Card(GP5-126) 2)18GB,7,200rpm SCSI Cable(GP5-841) SCSI Card SCSI Cable(GP5-841) SCSI Card SCSI Card(GP5-126) Configuration SCSI SCSI Cable(GP5-843) 3)9GB,10,000rpm (SCSI Card can be used (GP5-127 *3) Daisy chain with primary (GP5-127 *3) SCSI Cable(GP5-841) 4)18GB,10,000rpm for both HDD and backup connected device connection (SCSI Card can be used 5)36GB,10,000rpm backup device) (SCSI Card is required per for both HDD and backup device) device) Wide device: SCSI Card (GP5-127 *3) IDE IDE Onboard Primary IDE 1)30GB, 5400rpm SCSI Card(GP5-127 ) SCSI Card(GP5-127) Narrow device: Configuration UltraDMA/33 SCSI Cable(GP5-840) SCSI Cable(GP5-840) SCSI Card(GP5-127) 1)9GB,7,200rpm Daisy chain with primary SCSI Cable(GP5-840) Array Ultra2 Wide RAID Card 2)18GB,7,200rpm connected device Wide device: Configuration SCSI (GP5-143) 3)9GB,10,000rpm SCSI Card (GP5-127 *3) SCSI Cable(GP5-843) 4)18GB,10,000rpm 5)36GB,10,000rpm *1 Narrow connect devices: GP5UDT301/GP5USL501 *2 Wide connect devices: GP5-DT401/GP5-ML301(SCSI Cable is standard equipment with all Wide connect devices) *3 Daisy chain is not available for connection of a Wide SCSI device to SCSI Card(GP5-127) Connection Table GP5T2AB1A3: GP5T2AK1A3: 1CPU(Pentium(R)lll800MHz)/Pedestal Type 1CPU(CeleronTM 633MHz)/Pedestal Type <Items> Memory addition : Standard memory conversion : SCSI configuration Internal Hard Disk Drive (Ultra Wide) : Internal backup device : IDE/Array configuration Internal Hard Disk Drive (IDE) : Internal Hard Disk Drive (Array) : Internal backup device : Others (NIC, PSU, etc.) : GoTo A GoTo B GoTo C GoTo D GoTo E GoTo F GoTo G GoTo H 34

35 Memory Max:768MB (256MB SDRAM-DIMM x3) A: 2 Additional Memory-64MB (64MB SDRAM-DIMMx1) Standard:128MB (128MB SDRAM-DIMMx1) GP5-RM64H/GP5BRM64H Additional Memory-128MB (128MB SDRAM-DIMMx1) GP5-RM12H/GP5BRM12H Additional Memory-256MB (256MB SDRAM-DIMMx1) GP5-RM25H/GP5BRM25H Standard Memory conversion option B: 2 Standard Memory Conversion Kit-256MB (256MB SDRAM-DIMMx1) GP5BRU25D Internal HDD / Internal backup device (SCSI Configuration) Max:Four HDDs C: 6 Hard Disk Drive-9GB(Ultra2 Wide SCSI,7,200rpm) GP5-HD9G3/GP5BHD9G3 (For HDD bay:up to 3HDDs can be mounted) SCSI Card SCSI Cable GP5-HD9G3C /GP5BHD9G3C (For 5"bay:Only one can be mounted) GP5-126/GP5B126 GP5-843/GP5B843 Hard Disk Drive-18GB(Ultra2 Wide SCSI,7,200rpm) GP5-HD8G1/GP5BHD8G1 (For HDD bay:up to 3HDDs can be mounted) GP5-HD8G1C/GP5BHD8G1C(For 5"bay:Only one can be mounted) Hard Disk Drive-9GB(Ultra2 Wide SCSI,10,000rpm) GP5-HD9G4/GP5BHD9G4 (For HDD bay:up to 3HDDs can be mounted) Hard Disk Drive-18GB(Ultra2 Wide SCSI,10,000rpm) GP5-HD8G2/GP5BHD8G2 (For HDD bay:up to 3HDDs can be mounted) Backup device (Narrow) Hard Disk Drive-36GB(Ultra2 Wide SCSI,10,000rpm) GP5-HD6G1/GP5BHD6G1 (For HDD bay:up to 3HDDs can be mounted) D: DAT unit (DDS3) SCSI Cable GP5UDT301/GP5BDT301 GP5-841/GP5B841 Only one DDS3 can be mounted in "bay2" Backup device (Wide) Max.2 backup devices can be mounted Tape unit (SLR5) GP5USL501/GP5BSL501 6 DAT unit (DDS4) GP5-DT401/GP5BDT401 SCSI Card GP5-127/GP5B127 Tape unit (MLR3) GP5-ML301/GP5BML301 (IDE configuration) Max:2 IDE Disk can be mounted E: 3 Hard Disk Drive-30GB(Ultra33/DMA,5,400rpm) GP5-HD3E2/GP5BHD3E2 (Array configuration) F: 6 Go to SCSI Hard Disk Drive as above RAID Card (8MB Cache, Ultra2 Wide SCSI, SCSI Cable Only for internal HDD connection) GP5-843/GP5B843 GP5-143/GP5B143 35

36 SCSI Card (GP5-127/GP5B127) is required for mounting backup devices as shown below. G: 6 DAT unit (DDS3) SCSI Card GP5UDT301/GP5BDT301 GP5-127/GP5B127 SCSI Cable GP5-840/GP5B840 Max.2 backup devices can be mounted Tape unit GP5USL501/GP5BSL501 DAT unit (DDS4) GP5-DT401/GP5BDT401 SCSI Cable is supplied as standard equipment with wide backup devices. Tape unit (MLR3) GP5-ML301/GP5BML301 Others H: 6 LAN Card GP5-183/GP5B183 6 LAN Card GP5-185/GP5B185 6 LAN Card GP5-186/GP5B186 6 LAN Card GP5-187/GP5B187 6 GP5USM103/GP5BUSM103 PRIMERGY TS220/120 Specification Product TS220 TS120 Type Rackmount Product ID GP5T2TBER GP5T2TBBR GP5T1TBER GP5T1TBBR CPU Pentiumlll Frequency 933MHz 800EBMHz 933MHz 800EBMHz Secondary cache 256KB Number of CPUs 1 (up to 2) 1 Memory Standard 128MB (128MB x 1) Maximum 2GB (512MB x 4) VRAM 4MB VGA chip: ATI RAGE XL(PCI) Internal Bays 5-inch One (For CD-ROM) CD-ROM (Option) 24X Lowprofile (IDE) HDD bay 1inch x 2 (Hotplug) 1inch x 2 (Non Hotplug) Standard HDD 1x9.1GB/7200rpm(Ultra160) 1x30.7GB/5400rpm(IDE) Available HDD (Ultra160) 9.1GB(7200rpm)/18.2GB(7200rpm)/36.4GB(10000rpm) 30.7GB/5400rpm(IDE) Maximum 72.8GB (36.4GB x 2) 61.4GB (30.7GB x 2) Expansion slot PCI64bit 66MHz x1 SCSI Interface Ultra160 x1 (Itl.), Ultra Wide (Ext..) Ultra Wide (Ext..) RAID controller Option - Network LAN(10/100 base TX) x 2 (onboard) Dimension (mm) 481(W)x578(D)x42(H) Rackmount 1U Weight Max. 11kg Power consumption Max. 150W Power supply One standard units 36

37 Mounting additional memory The mother board has four slots for RAM modules (including base memory), install RAM modules in slot number order. Mounting internal SCSI devices TS220 has two HDD bays and 36.4GB/18.2GB/9.1GB Ultra160 SCSI HDD (1"height) can be mounted. TS120 has two HDD bays and 30.7GB IDE HDD (1"height) can be mounted. PRIMERGY TS220/120 Connection of internal HDD and internal backup devices Mother Board of TS220 Mother Board of TS120 EIDE controller For CD-ROM (Opt) Secondary EIDE controller ForCD-ROM (Opt.) Ultra160 SCSI controller For Internal HDD Primary EIDE controller For Internal HDD Ultra Wide SCSI controller For connection of external SCSI devices Ultra Wide SCSI controller For connection of external SCSI devices Internal HDD External backup device Connection Pattern One device is connected Two devices are connected Connection Interface Host Internal HDD Narrow connect Wide connect Narrow device x 2 Narrow device x 2 Narrow device and TS220 device *1 device *2 Wide device SCSI Onboard SCSI 1)9GB, 7,200rpm (Std.)Backup Cabinet (GP5UR1BC2) ConfigurationUltra160 (Ultra160) 2)18GB, 7,200rpm SCSI Cable (GP5S-832) is required 3)36GB, 10,000rpm Up to four backup devices can be mounted in GP5UR1BC2. Connection Pattern One device is connected Two devices are connected Connection Interface Host Internal HDD Narrow connect Wide connect Narrow device x 2 Narrow device x 2 Narrow device and TS120 device *1 device *2 Wide device IDE Onboard EIDE 30.7GB, 5400rpm Backup Cabinet (GP5UR1BC2) ConfigurationPIO (Primary) (One HDD is Standard SCSI Cable (GP5S-832) is required equipment) Up to four backup devices can be mounted in GP5UR1BC2. *1 Narrow connect devices: GP5UDL201/GP5UDT301/GP5USL501 *2 Wide connect devices: GP5-DT401/GP5-ML301(SCSI Cable is standard equipment with all Wide connect devices) Connection Table TS220 GP5T2TBER: GP5T2TBBR: TS120 GP5T1TBER: GP5T1TBBR: 1CPU(Pentium(R)lll933MHz)/Rackmount Type 1CPU(Pentium(R)lll800EBMHz)/Rackmount Type 1CPU(Pentium(R)lll933MHz)/Rackmount Type 1CPU(Pentium(R)lll800EBMHz)/Rackmount Type <Items> CPU Field upgrade : GoTo A Memory addition : GoTo B Internal devices: 1. IDE HDD connection (TS120) GoTo C 2. SCSI HDD connection (TS220) GoTo D 3. Array HDD connection (TS220) GoTo E 4.Backup device: GoTo F Others (NIC, PSU, etc.) : GoTo G 37

38 CPU (Only TS220) Max : 2CPUs A: 1 CPU Field Upgrade Kit-83 (Pentium III-933MHz (256KB) x1) GP5-FG22E/GP5BFG22E CPU Field Upgrade Kit-82 (Pentium III-800EBMHz (256KB) x1) GP5-FG23B/GP5BFG23B *CPU addition is only available on TS220 Memory Max:2GB B: 2 Additional Memory-128MB (128MB SDRAM-DIMMx1) Standard:128MB (128MB-DIMMx1) GP5-RM12M/GP5BRM12M Additional Memory-256MB (256MB SDRAM-DIMMx1) GP5-RM25M/GP5BRM25M Additional Memory-512MB (512MB SDRAM-DIMMx1) GP5-RM51M/GP5BRM51M Standard Memory conversion option 2 Standard Memory Conversion Kit-256MB GP5BRU25H Standard Memory Conversion Kit-512MB GP5BRU51L Internal HDD / Internal backup device TS120 Number of mountable HDD: Two C: 3 Hard Disk Drive-30GB(EIDE, 5,400rpm) (Standard equipment) * IDE HDD is only available on TS120 TS220 Number of mountable HDD: Two SCSI Connection: D: 3 Hard Disk Drive - 9GB (Ultra 160, 7,200rpm)(Hot Plug) GP5-HDH9B/GP5BHDH9B Hard Disk Drive -18GB (Ultra160, 7,200rpm)(Hot Plug) GP5-HDH88/GP5BHDH88 Hard Disk Drive -36GB (Ultra160, 10,000rpm)(Hot Plug) GP5-HDH63/GP5BHDH63 Array Connection: *SCSI HDD is only available on TS220 E: 6 Hard Disk Drive - 9GB (Ultra 160, 7,200rpm)(Hot Plug) RAID Card SCSI Cable GP5-HDH9B/GP5BHDH9B (64MB Cache/Ultra160) GP5-845/GP5B845 GP5-148/GP5B148 Hard Disk Drive -18GB (Ultra 160, 7,200rpm)(Hot Plug) GP5-HDH88/GP5BHDH88 Hard Disk Drive -36GB (Ultra160, 10,000rpm)(Hot Plug) GP5-HDH63/GP5BHDH63 *SCSI HDD is only available on TS220 38

39 CD-ROM unit (24X, Lowprofile) 4 GP5-CD312/GP5BCD312 F: 9 Backup Cabinet DLT unit (DLT4000) GP5UR1BC2 GP5UDL201GP5BDL201 SCSI Cable * Two 5"bays are occupied GP5S-832 DAT unit (DDS3) GP5UDT301/GP5BDT301 Up to four backup devices can be mounted in GP5UR1BC2 Tape unit GP5USL501/GP5BSL501 DLT unit (DLT7000) GP5-DL351/GP5BDL351 * Two 5"bays are occupied DAT unit (DDS4) GP5-DT401/GP5BDL401 Tape unit (MLR3) GP5-ML301/GP5BML301 DAT autoloader (DDS4) GP5-DTA102/GP5BDTA102 Occupied two 5" bay slots DAT autoloader (DDS3) GP5-DTA101/GP5BDTA101 Occupied two 5" bay slots Redundant Power Supply Unit G: Others GP5UPU151 6 LAN Card GP5-183/GP5B183 6 LAN Card GP5-185/GP5B185 6 LAN Card GP5-186/GP5B186 6 LAN Card GP5-187/GP5B187 39

40 External Disk Array PRIMERGY HS910 MS610 MS380 6 SCSI Card SCSI Cable External Disk Array GP5-123 (Procured locally) External Devices (Pedestal only) HS910 MS610 MS380 ES320 ES280 ES210 ES200 Hard disk cabinet Disk addition 6 SCSI card SCSI cable GP5-125/GP5B125 GP5MU823A Disk array 6 RAID card(cache:16mb) SCSI cable GP5U141/GP5BU141 GP5MU829A Disk addition 6 6 SCSI card SCSI cable GP5-127/GP5B127 GP5MU823A Disk array Hard disk cabinet 6 RAID card(cache:32mb) SCSI cable GP5MS623A GP5-144/GP5B144 GP5S-832 Disk array 6 RAID card(cache:64mb) SCSI cable Except ES320 GP GP5S-832 Disk array 6 6 RAID card(cache:16mb) SCSI cable GP5-145/GP5B145 GP5S-832 GP5-146/GP5B146 6 RAID card(cache:64mb) SCSI cable GP5-148/GP5B148 GP5S-832 Except 40