Manual and application description 4 channel 0-10V dimmer V2.0

Transcription

1 1 Manual and application description 4 channel 0-10V dimmer V2.0

2 2 1. Device description 1.1 General 0-10V dimmer is used for proportional control of 4 electronic ballasts with 1-10 V signal. There are also three binary inputs for manual push button control. Note! There are ballasts on the market with 0-10V control; additional contactor should be installed in this case to switch the ballast fully off. 1.2 Range of application Module is used for control of electronic ballasts with 1-10V signal. E.g. by sending 1% value, output gives 1 V, 100% - 10 V. 1.3 Installation The device is designed for DIN-rail mounting; it s tiny and requires only 1 DIN-unit of mounting space. 1.4 Features 4 separate 0-10V channel dimming 3 x binary inputs for optional manual control via push buttons Recognition of the last state of each channel Feedback of the switching state and brightness value 15 various preprogrammed scenes with defined brightness values, more available through Logic Machine with transition time SOFT on, SOFT off timer Status object shows of output LOCK binary object allows blocking all manual input controls Powered over KNX/EIB bus Compact design 1.5 Default settings To reset the device to default settings, press and hold programming button for more than 10 seconds. Programming LED will blink several times after releasing the programming button. The device will restart automatically after the reset is complete. 1.6 Terminals Outputs and KNX/EIB bus wires are connected using CAGE CLAMP mounting system. Push button A 1 4 Channel A 0-10V Dimmer Push button B Channel B 2 5 Push button C Channel C 3 6 Programming LED Programming button KNX/EIB 7 Channel D 8 GND

3 3 1.7 Technical data Power supply Channels Inputs Connections Supply voltage Voltage margin 29 VDC by KNX bus VDC Number 4 Output type 0-10 V analog PWM frequency 1.5 khz Number 3 Input type push button KNX/EIB Inputs /Outputs CAGE CLAMP mounting system CAGE CLAMP mounting system Operating and display Programming LED For assigning the physical address elements Programming button For assigning the physical address Type of protection IP20 In accordance with DIN EN Temperature range Physical Certification Operation Storage -5 C 45 C -25 C 55 C Design DIN rail mounted device for installation on 35mm mounting rail Housing / Color Polyamide / Grey Dimensions 15 x 91 x 56 mm (W x H x D) Weight 0,1 kg CE, RoHS In accordance with EMC and low-voltage guidelines Certificate

4 4 2. Application description 2.1 Default state of the device Factory-new devices have the physical address , no group addresses. 2.2 ETS configuration Channel configuration All four channels have identical settings. On object behavior object behavior on on state use previous or preset brightness Brightness preset [1..100] preset brightness level Soft on timer (seconds) [0..15] soft start timer Soft off timer (seconds) [0..15] soft stop timer Soft transition (seconds) [0..15] soft transition timer if used with scene settings keep time (seconds) [ ] time to play the scene transition time (seconds) [0..16] transition time between scenes

5 s settings Number of scenes to use [1..15] number of scenes parameters All scenes have identical settings. [0..100%] channel A brightness level [0..100%] channel B brightness level Channel C [0..100%] channel C brightness level Channel D [0..100%] channel D brightness level Manual push button control There are three binary inputs built in the device allowing manually control first three 0-10 V channels.

6 Object description

7 7 Object Name Type Comm. Read Write Transmit Comments Channel C Channel D Channel C Channel D Out: On/off Out: On/off Channel C Out: On/off Channel D Out: On/off Channel C Channel D number step random keep time transition time Manual input lock (5.001 scaling) In: Number (1..15) In: Up/down In: Seconds ( ) 7.* 2-Byte Unsigned In: Seconds (0..16) Random scenes in Time to play for specific scene Transition time between scenes Lock manual input Technical support Any faulty devices should be returned to Embedded Systems. If there are any further technical questions concerning the product, please, contact our support, available Mon-Fri 9:00 17:00 GMT 02:00. Please write to support@genohm.eu or call Firmware updates are available at