Surge Protection Devices and Surge Protection Kit
|
|
- Linda Brooke Doyle
- 5 years ago
- Views:
Transcription
1 Surge and Surge Kit SPD s protect electrical and electronic equipment against transients, originating from lightning, switching of transformers, lighting and motors 3. Main protection - class 3 To cut-down the transient surge as low as possible to protect very sensitive equipment. SPDs can be used in any supply system e.g TNCS, TNS, TT. Options: Replacement cartridges. power supply. Cartridges are available for all discharge currents (40kA and 15kA) with and without condition indication. These transients can cause premature ageing of equipment, downtime, or complete destruction of electronic components and materials. SPDs are strongly recommended on installations that are exposed to transients, to protect sensitive and expensive electrical equipment such as TV, video, washing machines, Hi-Fi, PC, alarm etc. The choice of SPD depends on a number of criteria such as: The risk of lightening strikes The exposure of the building to transients. The sensitivity and value of the electrical equipment that requires protection. Earthing system Level of protection The range of SPDs is separated into 3 types of protection: 1. Main protection - class 1 SPDs with higher discharge current (Imax 10/350), to evacuate as much of the transient overvoltages associated with lightening strikes 2. Main protection - class 2 With a discharge current (Imax 8/20), to evacuate as much of the transient overvoltage to earth as possible protection level (Up 1000V). Technical Data Complies with IEC Reserve Status Indicator (R versions) End of Life Indicator (D versions) OK Auxiliary contact for remote signalling (R versions only) V~ 1A 12V... 10mA Installation and Connection The main protection SPDs are installed directly after the main incoming switch or RCCB (type S). Connected in parallel to the equipment to be protected. is assured in both common and differential modes. SPDs with Low Let Through Voltage Levels Type 3 To protect very sensitive electronic equipment. This fine protection complements the main protection and can protect 1 or many electronic devices. Optimal coordination is obtained when cascaded with a main protection device. Discharge current Imax. 8kA (8/20 wave) a green LED on the front face indicates the status of the SPD SP202N, connected in series with the equipment that needs to be protected (with a maximum line current of 25A). is assured in both common and differential modes Connection Capacity Terminal blocks L, N & E Rigid conductor: 10mm 2 Flexible conductor: 6mm 2 Replacement Cartridges The cartridges replace the cartridge in the main SPN* devices. They allow simple replacement without the need to cut-off the A keying system exists to prevent a line cartridge being interchanged by mistake with a neutral one and visa versa neutral cartridges have a discharge current of 65kA For technical details see page TNS TNC-S TT SPA201 SPA400 SPA401 SPN800 SPN801 SPN802 SPN215D SPN240D SPN415D SPN440D SP202N Class (Class if less than 5m) (with lifetime indicator) Poles I imp ka I imp ka I n In Up kv Single or Width (mm) Cat ref. Cat ref Single 35 SPA201* Three 70 SPA400* Three 70 SPA Three 105 SPN800 SPN800R Three 140 SPN801 SPN801R Three 140 SPN802 SPN802R * These SPD devices are of the monoblock type construction. At end of life, the complete product should be replaced. SPN800R Replacement Cartridges (SPN8* range) Dimensions Phase replacement for SPN800, SPN800R, SPN801, SPN801R, SPN802 & SPN802R Neutral replacement for SPN801, SPN801R, SPN802, SPN802R Cat ref. SPN080 SPN080N SPN080N 4.30 General Catalogue
2 Class 2 (with lifetime indicator) Single 35 SPN215D SPN215R Single 35 SPN240D SPN240R Three 70 SPN415D SPN415R Three 70 SPN440D SPN440R Replacement Cartridges SPN415D Dimensions Phase replacement for SPN140D Phase replacement for SPN215D & SPN415D Phase replacement for SPN215R & SPN 415R Neutral replacement for SPN215D, SPN415D, SPN215R & SPN415R Cat ref. SPN040D SPN015D SPN015R SPN040N SPN040D Class 3 (fine protection) (with lifetime indicator) Single 35 SP202N - PV Applications (DC side) (with lifetime indicator) SPV325 - SPV325 Consumer Unit Kit Type 2 SPD with SPN215D (with lifetime indicator) Consists of: Neutral terminal bar, 3x 20mm neutral link bar 370mm, 300mm & 200mm lengths, 4mm 2 neutral, live & earth cables, 2 connector busbar, 4 way terminal bar, terminal bar clip, 1x Double Pole SPD s, 32A MCB Single 35 VA02SPD - Customer Services Hotline Technical Support Helpline
3 Type 2 / Class II Surge SPN215*, SPN240*, SPN415*, SPN440* & SPV325 SPA201 SPA400 SPA401 Tested to EN L Þ N N Þ PE L1/L2/L3 Þ PEN L1/L2/L3 Þ N N Þ PE SPD type / class T1 / Class I Energy-coordinated Type 1 + Type 2 protection effect on terminal equipment Energy-coordinated Type 1 + Type 2 + Type 3 protection effect on terminalequipment 5 m Type of power supply TT / TN system TN-C system TT / TN-S system system Type of protection common and differential modes common modes common and differential modes Nominal voltage U N 230V/400V ac Rated voltage U c 255V ac Voltage protection level U p 1.5kV TOV Voltage U T 440V / 5s 1200V / 200ms 440V / 5s 440V / 5s 1200V / 200ms Rated load current I(L) nc I(L-L) nc Follow current interrupting I fi 25kA rms 100A rms 25 ka rms 25kA rms 100A rms rating Nominal discharge current I n 12.5kA 25kA 12.5kA (L-PEN) 37.5kA (total) 12.5kA 50kA (8/20) Impulse current (10/350) I imp 12.5kA 25kA 12.5kA (L-PEN) 37.5kA (total) 12.5kA 50kA Maximal rating of fuse 160A gl / gg MCB nc Short-circuit withstand fuse 25kA rms capability with max. MCB nc Response time t A 100ns Operating temperature range J - 40 C.+ 80 C Indication of SPD disconnector Green/Red flag on L and N Green/Red flag on L1, L2, L3 Green/Red flag on L1, L2, L3 and N Cross sectional area min 1,5mm 2 solid / flexible max 35mm 2 stranded / 25mm 2 flexible 4 Nm Enclosure material grey thermoplastic, UL 94V-0 Modular width Weight 275 g g g Approval marking KEMA Customer Services Hotline Technical Support Helpline
4 Type 1 / Class I Surge SPN8*** Tested to EN (VDE ) SPN800 / SPN800R SPN801 / SPN801R SPN802 / SPN802R EN (VDE ) EN (VDE ) L1/L2/L3 Þ PEN L1/L2/L3/N Þ PE L1/L2/L3 Þ N N Þ PE SPD type / class T1 / I / B Type of power supply system TN-C - System TN-S - System TT - System Type of protection Common modes Common and differential modes Nominal voltage U N 230V / 400V ac Rated voltage U c 255V ac Voltage protection level U p 1.5kV 255V ac TOV-voltage U T 440V / 5s 1200V / 200ms Rated load current I(L) 315Aeff I(L-L) 125Aeff Follow current interrupting rating I fi 50 kaeff 100kA Nominal discharge current (8/20) I n 75kA 100kA 25kA 100kA Impulse current (10/350) I imp 75kA 100kA 25kA 100kA Residual current I PE 100mA Maximal rating of overcurrent fuse 125A gl / gg serial or 315A parallel protection MCB 125A serial or 160A parallel C curve Short-circuit withstand capability with max. fuse 50kA eff ac 25kA eff ac MCB 50kA eff ac 25kA eff ac Response time t A < 100ns Isolationswiderstand Risol --- Operating temperature range J - 40 C.+ 60 C Indication of SPD disconnector Green - red on L1, L2, L3 Green - red on L1, L2, L3, N Cross sectional area min 10mm 2 solid / flexible L1, L2, L3, PE max 50mm 2 multi-stranded / 35mm 2 flexible L1', L2', L3', PE max 35mm 2 multi-stranded / 25mm 2 flexible 7.0 Nm Enclosure material grey thermoplastic, UL 94V-0 Modular width 6 8 Weight 970 g 1260 g 1272 g Approval marking VDE 4.34 General Catalogue Technical
5 Type 2 / Class II Surge SPN215*, SPN240*, SPN415* & SPN440* SPN215D/R SPN240D/R SPN415D/R SPN440D/R Tested to EN (VDE ) SPD type Type 2 according to EN SPD class Class II according to IEC Maximum continuous operationg voltage U c Phase / Neutal 255V Neutral/ PE 275V Voltage protection level U p 1kV 1.2kV 1kV 1.2kV Nominal discharge current (8/20 µs) I n 5kA 15kA 5kA 15kA [(DC+/DC-) --> PE] Max. discharge current (8/20 µs) [(DC+/DC-) --> I max 15kA 40kA 15kA 40kA PE] Short-circuit withstand capability with max. 10kA - 32A 20kA - 32A 10kA - 32A 20kA - 32A Operating temperature range J - 40 C.+ 80 C Indication of SPD disconnector Green - Yellow - Red Cross sectional area min 1,5mm 2 solid / flexible max 35mm 2 multi-stranded / 25mm 2 flexible 4.0 Nm Enclosure material grey thermoplastic, UL 94V-0 Modular width (DIN 43880) Auiliary contact. Voltage/ nominal current (only applicable on the R suffix products) 230V/ 0.5A 12Vdc 10mA Customer Services Hotline Technical Support Helpline
6 Type 2 / Class II Surge SPV325 SPV325 Tested to EN (VDE ) SPD type Type 2 according to EN SPD class Class II according to IEC Maximum continuous operationg voltage Uc PV 1000V Voltage protection level U p 4kV Voltage protection level for 5kA U p 3,5kV Total discharge current (8/20 µs) I total 40kA Nominal discharge current (8/20 µs) I n 12.5kA [(DC+/DC-) --> PE] Max. discharge current (8/20 µs) I max 25kA [(DC+/DC-) --> PE] Short-circuit withstand capability with max. I scwpv 50 A / 1000 V DC Response time t A 25ns Operating temperature range J - 40 C.+ 80 C Indication of SPD disconnector green - red Cross sectional area min 1.5mm 2 solid / flexible max 35mm 2 multi-stranded / 25mm 2 flexible 4.0 Nm Enclosure material Grey thermoplastic, UL 94V-0 Installation width 3 modules, DIN Weight 316g 4.36 General Catalogue Technical
7 Type 3 / Class III Surge SP202N Characteristics Tested to EN (VDE ) SPD type / class T3 / III Ports one port Type of power supply system TT / TN system Nominal voltage U N 230V ac Rated voltage U c 255V ac Voltage protection level ( L- N) U p 1.25kV Voltage protection level (L/N - PE) U p 1.5kV TOV - Characteristic (L - N) U T 335V / 5s TOV - Characteristic (L/N - PE) (I) U T 400V / 5s TOV - Characteristic (L/N - PE) (II) U T 1200V / 200 ms Rated load current IL 16 Aeff Nominal discharge current (8/20) I n 3kA Maximal discharge current (8/20) I max 5kA Combination wave (1,2/50-8/20) (L - N) U oc 6 kv Combination wave (1,2/50-8/20) (L/N - PE) U oc 10 kv Residuel current IPE 5μA Remplacement cartridge NO Maximal rating of fuse 16 A gl / gg MCB 16A B curve Short-circuit withstand capability with max. fuse 6kA eff ac MCB 1kA eff ac Response time t A 25ns Operating temperature range J - 25 C.+ 40 C Indication of SPD disconnector NO Remote signalisation contact Green light off Cross sectional area min 1.5mm 2 solid / flexible max 10mm 2 stranded / 6mm 2 flexible 1.2 Nm Enclosure material Grey thermoplastic, UL 94V-2 Installation width 2 modules, DIN Reserve Indicator Light Neutral cartridges cannot be put into spares reserved for phase cartridges and visa versa. Normal Reserve End of Life Customer Services Hotline Technical Support Helpline
Surge Protection Devices Type 1+2
Surge Protection Devices Type 1+2 Description The combined surge protection devices offer as an all-in-one solution lightning and surge-voltage in one device. They are in accordance with the requirement
More informationTechnical features OVR Surge Protective Devices Type 1 & Type 1+2
Type 1 & Type 1+2 TECHNICAL FEATURES Technology Type 1 OVR T1 2 TS Triggered spark-gap Electrical features Standard IEC 61643-1 / EN 61643-11 Type / test class 1 / I Poles 1P - 1P -, 2P 2L 3P 3L 4P 4L
More informationLow voltage. Acti 9. the efficiency you deserve. Catalogue 03/2016
Low voltage Acti 9 the efficiency you deserve Catalogue 03/2016 schneider-electric.com 1 and 2 LV surge s 1 and 2 LV surge s (cont.) The 1 range of surge s meets the normative withstand capability of wave
More informationSurge Protection Devices Ex9UE2
Surge Protection Devices Ex9UE2 Surge Protection Devices Type 2 (Class II, T2, C) Tested according to EN 61643-11 Maximum continuous operational voltage U c from 275 V up to 440 V AC Versions with 1+0,
More informationTechnical Data. Circuit Protection - Surge Protection Devices. Ver 1.0 CUSPD1110. Brief product description:
Technical Data Circuit Protection - Surge Protection Devices Ver 1.0 CUSPD1110 Brief product description: Surge Protection Device (SPD) protect against lightning surges and man made surges such as motors,
More informationMULTI-POLE PHOTOVOLTAIC SYSTEMS. COMPACT and MODULAR Housing
MULTI-POLE Lightning Current and Surge Arresters for PHOTOVOLTAIC SYSTEMS Class I / (B+C) and Class II / (C) COMPACT and MODULAR Housing 44 PV ISPRO BS(R) 12,5 The PV ISPRO BS(R) 12,5 series of over voltage
More informationType of surge arrester
ipf surge arresters Type 2 or 3 LV surge arresters The ipf multi-pole single-piece surge arrester range is adapted for earthing systems: TT, TN-S,. Type 2 surge arresters are tested with a 8/20 µs current
More informationPRF1 12.5r/PRF1 Master/ PRD1 25r/PRD1 Master Type 1 and 2 LV surge arresters
Type 1 and 2 LV surge s The Type 1 range of surge s meets the normative withstand capability of wave type 10/350 μs (8/20 μs for Type 2 surge s). It is suitable for use with, TN-C and 230 V IT earthing
More informationOvervoltage Protection Devices
Siemens AG 2014 Overvoltage Protection Devices /2 Introduction /3 5SD7 lightning arresters, type 1 /5 5SD7 combination surge arresters, type 1 and type 2 /7 5SD7 combination surge arresters, type 1 / type
More informationOvervoltage Protection Devices
Siemens AG 2013 Overvoltage Protection Devices /2 Introduction /3 5SD7 lightning arresters, type 1 /5 5SD7 combination surge arresters, type 1 and type 2 /7 5SD7 surge arresters, type 2 /10 5SD7 surge
More informationOvervoltage Protection Devices
Siemens AG 201 /2 Introduction /3 5SD7 lightning arresters, type 1 /5 5SD7 combination surge arresters, type 1 + type 2 /7 5SD7 combination surge arresters, type 1 / type 2 /9 5SD7 surge arresters, type
More informationOvervoltage Protection Devices
Siemens AG 2010 Overvoltage Protection Devices /2 Introduction /3 Lightning Arresters, Type 1 /5 Combination Surge Arresters, Type 1 and Type 2 /7 Surge Arresters, Type 2 /11 Surge Arresters, Type 3 /12
More informationwietap wietap Overvoltage Protection Tensions running high
wietap wietap Overvoltage Protection Tensions running high 2 wietap wietap Overvoltage protection Important information on overvoltage The necessity of overvoltage protection on machines and systems as
More informationOvervoltage Protection Devices
Overvoltage Protection Devices /2 Introduction /3 5SD7 lightning arresters, type 1 /5 5SD7 combination surge arresters, type 1 and type 2 /7 5SD7 surge arresters, type 2 /10 5SD7 surge arresters, type
More informationMiniature. Circuit Breakers. reliable solutions for protection of installations against over-current phenomenon. Advantages for you : Technical data :
Miniature Circuit Breakers reliable solutions for protection of installations against over-current phenomenon Advantages for you : Bi-connect terminals for simultaneous termination of bus bar & wires Unique
More informationCONTA-ELECTRONICS. CONTA-PROTECT overvoltage protection
CONTA-ELECTRONICS CONTA-PROTECT overvoltage protection When choosing the correct device for overvoltage protection, it is important to consider the regulations VDE 110-1, IEC 61643-1, EN 61643-11 and VDE
More informationSPD Catalogue. SPD Catalogue. for AC applications
SPD Catalogue SPD Catalogue for AC applications Eaton and Cooper united. Energizing a world that demands more. We deliver: Electrical solutions that use less energy, improve power reliability and make
More informationSPM Series Plug-in Surge Protector Type 2/3 (Test Class II/III) Single & Three Phase Surge Arresters
The SPM series of modular surge protection devices provides protection of equipment connected to incoming low voltage AC power supplies against the damaging effects of transient over voltages caused by
More informationLeutron. Lightningand. Surge Protection for Power Net Systems (SPD) with EnerPro Combi-Devices. Seite 0 von14
Leutron Lightningand Surge Protection for Power Net Systems (SPD) with EnerPro Combi-Devices Seite 0 von14 Novelties 2003 Combi Surge Protectors Leutron GmbH, 70771 Leinfelden-Echterdingen, Deutschland
More informationSPM Series Plug-in Surge Protection
SPM Series Plug-in Surge Protection The SPM series of modular surge protection devices provides protection of equipment connected to incoming low voltage AC power supplies against the damaging effects
More informationSingle Pole SPD. Model V20/75-S V20/150-S V20/275-S V20/320-S V20/385-S V20/420-S V20/440-S V20/550-S EN/IEC / UL th
V20 -S U oc 20kV ¾ SPD with high energy MOV technology ¾ Max discharge current up to 20kA 8/20μs and open circuit voltage U oc to 20kV. ¾ Pluggable module for easy replacement ¾ Reliable thermal disconnector
More information3 Design of the electrical installation protection system
J - Protection against voltage surges in LV 3 Design of the electrical To protect an electrical installation in a building, simple rules apply for the choice of b (s); b its protection system. 3.1 Design
More informationETITEC - Lightning and Surge Arresters
ETITEC Lightning and Surge Arresters Overvoltage protection selection ETITEC selection Define system data: U max Uc > 1,2 x U max External lightning protection exist? NO Apply ETITEC C on string and on
More informationTT-ST-M-2-PE-24DC. Extract from the online catalog. Order No.:
Extract from the online catalog TT-ST-M-2-PE-24DC Order No.: 2858904 TERMITRAB, spring-cage modular terminal block with integrated surge protection and disconnect knives, for assembly on NS 35/7.5, voltage
More informationPT 2-PE/S- 24AC-ST. Extract from the online catalog. Order No.:
Extract from the online catalog PT 2-PE/S- 24AC-ST Order No.: 2839318 The illustration shows version PT 2-PE/S-230 AC-ST Protective plug PT with surge voltage equipment protection for power supply units,
More informationR3&A Limited, Cobourg, ON
R3&A imited, Cobourg, ON ightning and Surge Protection Devices for North America Easy Choice POWER SUPPY SYSTEMS Main distribution board (Category C) Class I ightning current arrester Subdistribution board
More informationmcbs, EQUIPMENT NEW PRODUCTS 2014 Voltage surge protectors & other control and signalling devices Time & light sensitive switches
NEW P. 4 RX3 MCBs 63 A 4500 & 6000 prong type busbar MCBs, RCDs, add-on modules & accessories P. 9 DX3 RCBOs 63 A 6000 / 10 ka AC, A & Hpi type prong & fork type busbar P. 16 DX3 MCBs 63 A 50 ka mcbs,
More informationSurge Protective Device
Surge Protective Device LED Light / Machine protection SPD Class 2 LT-C34G801W General Information LT-C and LT-HC series Surge Protective Devices are for protection of indirect lightning. They are designed
More informationUS Catalog March Surge protective devices (SPDs) UL range
US Catalog March 017 Surge protective devices (SPDs) UL range Surge protective devices (SPDs) UL range Introduction 1 1 OVR surge protective devices Joslyn surge protective devices Marketing tools 4 US
More informationPT 2X2-HF-24 DC-ST. Extract from the online catalog. Order No.:
Extract from the online catalog PT 2X2-HF-24 DC-ST Order No.: 2839729 The illustration shows the version PT 2x2-HF-12 DC-ST Protective plug PT with HF protective circuit for two 2-core floating signal
More informationLightning Current Equipotential Bonding SPDs
Lightning Current Equipotential Bonding SPDs Introduction Furse is a world leader in the design, manufacture, and supply of earthing and lightning protection systems. Over 100 years of experience makes
More informationLightning and Surge Arresters
Lightning and Surge Arresters 5/4 Product overview 5/5 Lightning arresters, requirement category I (B) 5/6 Combined arresters, requirement category I (B) and II (C) 5/7 Single-pole surge arrester, requirement
More informationPT 3-PB-ST. Extract from the online catalog. Order No.:
Extract from the online catalog PT 3-PB-ST Order No.: 2858030 Surge protection plug for the base element, normal mode voltage coarse and fine protection for two floating signal wires in IT, common mode
More informationModular surge protective devices
S D 870 LIMOGES Cedex Telephone: (+33) 05 55 06 87 87 - Fax: (+33) 05 55 06 88 88 Modular surge protective devices Cat. o(s): 039 10-030 00/0//3/7 age /L 1. General characteristics... 1. Overall dimensions....1-3.
More informationNEW surge protective devices
NEW surge protective devices For use in low-voltage systems For overhead power lines and buildings Made in EU ABOUT COMPANY INTRODUCTION Company ELEKTROMEHANIKA & BB d.o.o. was established from recent
More informationVAL-CP-1S-175. Extract from the online catalog. Order No.:
Extract from the online catalog VAL-CP-1S-175 Order No.: 2859479 Pluggable type 2 arrester (surge arrester) for 1-phase current supply networks with separate N and PE (3-conductor system: L1, N, PE), with
More informationModular surge protective devices (SPDs)
128, av. du Maréchal-de-Lattre-de-Tassigny - 87045 LIMOGES Cedex Tel : 0 (+33) 5 55 06 87 87 Fax : 0 (+33) 5 55 06 88 88 www.legrand.com Modular surge protective devices (SPDs) CONTENTS Page 1. General
More informationBuilding Surge Protection Information Pack
Building Surge Protection Information Pack For All Your Surge Solutions PD Devices Ltd. Old Station Yard, South Brent, Devon, UK, TQ10 9AL W: www.pddevices.co.uk T: +44 (0)1364 649248 E: sales@pddevices.co.uk
More informationSurge & Filter Protection Addressing your industrial power quality needs.
Surge & Filter Protection Addressing your industrial power quality needs. BULLETIN 983 INTRODUCING SURGE & FILTER PROTECTION SURGE & FILTER PROTECTION Rockwell Automation is pleased to introduce the Bulletin
More informationModular surge protective devices (SPDs) Cat. Nos :
Contents Page 1. General characteristics...2 2. Overall dimensions...4 3. Technical characteristics...4 4. Conformity...9 5. Mounting...9 6. Accessories.............................11 Product information
More informationSPM Series. Plug-in Surge Protection
SPM Series Plug-in Surge Protection The SPM series of modular surge protection devices provides protection of equipment connected to incoming low voltage AC power supplies against the damaging effects
More informationModular surge protective devices (SPDs)
128, av. du Maréchal-de-Lattre-de-Tassigny - 87045 LIMOGES Cedex Tel : 0 (+33) 5 55 06 87 87 Fax : 0 (+33) 5 55 06 88 88 www.legrand.com Modular surge protective devices (SPDs) CONTENTS Page 1. General
More informationSURGE PROTECTION LIGHTNING & EARTHING EQUIPMENT
SURGE PROTECTION LIGHTNING & EARTHING EQUIPMENT FOR INDUSTRIAL, COMMERCIAL AND DOMESTIC ELECTRICAL INSTALLATIONS Surge Protection Devices and its Partner Companies have been solving problems in Lightning
More informationExtract from the online catalog SFP 1-5/120AC Commercial data Product description Technical data Standards
Extract from the online catalog SFP 1-5/120AC Order No.: 2920667 Device surge protection filter to limit powerful surge voltages, mounting on NS 35. Commercial data EAN 4046356158558 Pack 1 pcs. Customs
More informationOvervoltage Protection for low-voltage supplies
Class I Overvoltage Protection.2 -.3 with sparkover gaps.4 -.9 with high-power varistors.10 -.11 Overvoltage Protection, combination arrester.12 -.15 Class II Overvoltage Protection with varistors.16 -.25
More informationSurge protection for gutter heating systems
Surge protection for gutter heating systems White Paper Contents Structure without external lightning protection system Structure with external lightning protection system www.dehn-international.com Surge
More informationAutoprotected Surge Arresters New OVR Plus range
Autoprotected Surge Arresters New OVR Plus range A complete solution with the OVR PLUS range Thanks to its continuous innovation on surge protection, ABB improves constantly its offer by launching on the
More informationPT 5-HF- 5 DC-ST. Extract from the online catalog. Order No.:
Extract from the online catalog PT 5-HF- 5 DC-ST Order No.: 2838762 The illustration shows variant PT 5-HF-12 DC-ST Protective plug PT with HF protective circuit for 4 signal wires. Nominal voltage: 5
More informationCoordination of Surge protection devices
Coordination of Surge protection devices Design guide Surge arresters for commercial and industrial buildings Surge protection devices: how to choose them? coordination How to choose surge protection devices?
More informationPT 2X2-24DC-ST. Extract from the online catalog. Order No.:
Extract from the online catalog PT 2X2-24DC-ST Order No.: 2838228 The illustration shows version PT 2x2-5DC-ST Protective plug PT with protective circuit for two 2-core floating signal circuits. Nominal
More informationType Code No. Weight Packaging [g] [pcs]
Surge arresters surge arresters are intended for protection of electrical installations and devices against overvoltage effects, which may occur in atmospheric discharges and switching overvoltages. The
More information2 Principle of lightning protection
2 Principle of lightning protection The system for protecting a building against the effects of lightning must include: bprotection of structures against direct lightning strokes; bprotection of electrical
More informationElectronic timer CT-ERD.12
2CDC 251 092 F0t06 a Rotary switch for the preselection of the time range b Potentiometer with direct reading scale for the fine adjustment of the time delay c U: green LED V control supply voltage applied
More informationSURGE PROTECTIVE DEVICES
SURGE PROTECTIVE DEVICES SUITABLE SOLUTIONS FOR ALL TYPES OF INSTALLATIONS AND ALL RISK LEVELS 1 CONTENT: Introduction Theory and principles Installation rules Legrand offer 2 2 INTRODUCTION Lightning
More informationLightning and surge protection for single-family houses
Lightning and surge protection for single-family houses White Paper Contents Benefits of protecting an antenna by means of an isolated LPS instead of earthing the antenna Protection of the heat pump /
More informationSurge protection for frequency converters
Surge protection for frequency converters White Paper Contents Basic principle of a frequency converter EMC-compatible shield connection of the motor feeder cable Frequency converter with drives in LPZ
More informationLightning & Surge Protection for Wind Turbine Systems
Lightning & Surge Protection for Wind Turbine Systems Product Selection Guide Table of Contents Technologies for Wind Turbine Protection 3 Protective Device Recommendations 4 Class I Strikesorb Surge Protection
More informationVAL-CP-3S-350. Extract from the online catalog. Order No.:
Extract from the online catalog VAL-CP-3S-350 Order No.: 2859521 Commercial data EAN 4017918977610 Pack 1 Pcs. Customs tariff 85363030 Weight/Piece 388.83 g Product key J020 Catalog page information Page
More informationElectronic timer CT-AHD.22
2CDC 251 093 F0t06 a Rotary switch for the preselection of the time range b Potentiometer with direct reading scale for the fine adjustment of the time delay c U: green LED V control supply voltage applied
More informationPV protective solutions
PV SPD catalogue PV protective solutions for solar PV applications Eaton and Cooper united. Energizing a world that demands more. We deliver: Electrical solutions that use less energy, improve power reliability
More informationPOWER SUPPLY SYSTEMS SPDs for low-voltage installations and equipment
SPDs for low-voltage installations and equipment 13 14 Easy Choice 16 Combined SPDs Type 1 Combined 25 49 59 65 113 139 15 ÜS-Schutz Combined Easy Choice L1 L2 L3 N PE SPD (Surge arrester) SPD (Surge arrester)
More informationTT-2-PE- 24DC. Extract from the online catalog. Order No.:
Extract from the online catalog TT-2-PE- 24DC Order No.: 2838186 Modular terminal block with three-stage surge protection for a floating double conductor, separate ground connection, nominal voltage: 24
More informationLightning and Surge Arresters
/ Lightning and Surge Arresters Product overview /3 Introduction /6 Lightning arresters, requirement category I (B) /8 Combination arresters, requirement category I (B) and II (C) /0 Single-pole surge
More informationPRACTICAL EXAMPLES OF OVERVOLTAGE PROTECTION
INTERNAL PROTECTION systems PRACTICAL EXAMPLES OF OVERVOLTAGE PROTECTION INDUSTRIAL INSTALLATIONS 2 1 2 5 5 7 2 2 2 2 4 6 6 7 3 OBJECT: Industrial premises, Industrial complexes, Hospitals, Public buildings
More informationElectronic timer CT-ARS.11
2CDC 251 088 F0t07 Features Rated control supply voltage 24 240 V AC/DC Single function OFF delay timer without auxiliary voltage One device includes 7 time ranges (0.05 s 10 min) 1 c/o (SPDT) contact
More informationTT-2-PE-M-24DC. Extract from the online catalog. Order No.:
Extract from the online catalog TT-2-PE-M-24DC Order No.: 2920641 Modular terminal block with two-stage surge protection for one operated floating double conductor, disconnect knife on both signal paths,
More informationProtection of PHOTOVOLTAIC SYSTEMS against LIGHTNING and OVERVOLTAGE. Surge Protection Device
Protection of PHOTOVOLTAIC SYSTEMS against LIGHTNING and OVERVOLTAGE Surge Protection Device CHOICE OF SURGE PROTECTION DEVICES FOR PHOTOVOLTAIC APPLICATIONS General concept To achieve complete functionality
More informationOvervoltage Protection
Overvoltage Protection OVR Range FRSOX 0100 03 GB ABB Lightning Protection Group 1 Main causes of transient overvoltages The solution: ABB OVR Surge Protective Device Range Lightning strike A lightning
More informationSurge protection for LED mast lights
Surge protection for LED mast lights White Paper Contents Surge arrester installed in the terminal compartment / distributor of the metal mast Surge arrester installed next to the LED mast light with the
More informationLightning and surge protection for electromobility
Lightning and surge protection for electromobility White Paper Contents Danger during thunderstorms Damage caused during charging What happens if lightning strikes when charging? What do the standards
More informationInstallation / Control Technique
Installation / Control Technique Interface Relay, Interface Relay System Input-Output Interface Relay IK 3070, I_ 3070 0633 IK 3070 Circuit Diagrams IS 3070 According to IEC/EN 61 810-1 Relay, triac or
More informationAllen-Bradley 1492-RCDA4A40
Dual terminals provide wiring/bus bar flexibility and clamp from both sides to improve connection reliability Suitable for DIN Rail mounting Approval marks are easily visible on dome Terminal design helps
More informationOvervoltage Protective Devices
Scan this tag to get product information about the New Bussmann Surge Protection products for UL, PV, IEC, Wind Power and Telecom applications. RED indicates NEW information Overvoltage Protective Devices
More informationRemote contact signaling available. visual status indication
Effective January 2016 Supersedes August 2013 BUSSMANN SERIES PV PRO three module photovoltaic surge protective devices for 600 and 1000Vdc systems Remote contact signaling available easyid local visual
More informationReliability in Surge Protection. Photovoltaic Systems.
Reliability in Surge Protection Photovoltaic Systems www.citelcp.com Roof top installations For low power PV applications, i.e. residences and small offices, it is necessary to consider surge protecting
More informationPage 14-4 Page Page 14-4 SURGE PROTECTION DEVICES TYPE 2 VERSIONS WITH PLUG-IN CARTRIDGE 1P, 1P+N, 2P, 3P, 3P+N, 4P
Page -4 Page -4 SURGE PROTECTIO DEVICES TY 1 AD 2 MOOBOCK VERSIOS 1P, 1P+, 2P, 3P, 3P+, 4P IEC impulse current Iimp (10/350μs): 25kA IEC maximum discharge current Imax (8/20μs): 100kA SPD status indicator
More informationS400 Series HIGH EFFICIENCY SURGE PROTECTIONS. For power supply For measurement and control devices For LAN / ICT Networks
S400 Series HIGH EFFICIENCY SURGE PROTECTIONS For power supply For measurement and control devices For LAN / ICT Networks S400 Series High Efficiency Surge Protections High Efficiency Surge Protections
More informationElectronic timer CT-ERS.12 ON-delayed with 1 c/o contact Data sheet
2CDC 251 056 F0t07 Features Rated control supply voltage 24-48 V DC, 24-240 V AC Single-function ON-delay timer One device includes 10 time ranges (0.05 s - 300 h) 1 c/o contact 2 LEDs for status indication
More informationBS th Edition wiring regulations Furse overview
BS 7671 18th Edition wiring regulations Furse overview Transient overvoltage protection TRANSIENT OVERVOLTAGE PROTECTION - RISK ASSESSMENT TO BS 7671 Furse electronic systems protection Enhanced solutions
More informationL*W*H:120*65*35.5 L*W*H:152*133*48 L*W*H:220*143*48 L*W*H:360*280*132 for 1ph 5A~10A for 1ph 10A~16A for 1ph 20A~45A for 1ph 50A~120A/200kA
Prosurge BSF series surge filter is two-port Surge Protective Device with LC Filter especially for low-voltage power supply system surge protection at the boundaries from lightning protection zone 0 B
More informationSurge Protection for Surveillance Systems
Surge Protection for Surveillance Systems 1-in-1 Protection for Network Cameras 2-in-1 Protection for Power and Audio/Video Signals 3-in-1 Protection for Power, Audio/Video and PTZ Control Signals Application:
More informationonlinecomponents.com Overvoltage protection Contents Overvoltage protection Overvoltage protection F.1
Contents for low-voltage supplies.2 for instrumentation and control equipment.40 for data interfaces.88.1 for low-voltage supplies for low-voltage supplies Class I overvoltage protection with sparkover
More informationElectronic timer CT-ERS.21
2CDC 251 057 F0t07 Features Rated control supply voltage 24 240 V AC/DC Single function ON delay timer One device includes 10 time ranges (0.05 s 300 h) 2 c/o contacts 2 LEDs for status indication Width
More informationCirprotec. Specialists in Lightning and Surge Protection for Photovoltaic Systems. Includes new plug-in SPD range and insulation monitoring device
A1 Cirprotec Specialists in Lightning and Surge Protection for Photovoltaic Systems Includes new plugin range and insulation monitoring device Complete protection systems with maximum continuity of service
More informationPROTEC Z LV the universal solution for transient switching protection for LV motors, generators, transformer LV secundaries, VSD and UPS equipment
PROTEC Z LV the universal solution for transient switching protection for LV motors, generators, transformer LV secundaries, VSD and UPS equipment NTSA has developed the ultimate solution for protecting
More informationSurge Protection for Low Voltage Power Systems
Surge Protection for Low Voltage Power Systems 2017 CATALOG Table of Contents About Raycap 3 Introduction 5 Regulatory Standards 6 Surge Protective Device Components & Terminology 8 Low Voltage Power Distribution
More informationTDS Transient Discriminating Surge Diverters
TDS Transient Discriminating Surge Diverters Surge Protection And Surge Ratings The stress, which an SPD will experience under surge conditions, is a function of many complex and interrelated parameters.
More informationIncreased Safety for Switchgear Cabinets CI Arresters with Integrated Backup Fuse
Increased Safety for Switchgear Cabinets CI Arresters with Backup Fuse www.dehn-international.com 1 fuse 1 2 fuse monitoring 2 3 Considerable space saving 3 Innovative solution to save space in the switchgear
More informationTT-UK5/ 24DC. Extract from the online catalog. Order No.:
Extract from the online catalog TT-UK5/ 24DC Order No.: 2794699 Modular terminal block with surge voltage fine protection between clamping connector and DIN rail, nominal voltage: 24 V DC, for mounting
More informationTechnology Live Workshop
Technology Live Workshop David Pitt Product Manager Eaton Electric Ltd. Technology Live Workshop Subjects to be covered in this Technology Live Workshop: Increased need for installation of transient voltage
More informationIssued February DATA SHEET 5SX2 MCB. Based on Siemens Industrial Control Catalog
Issued February 2011 DATA SHEET 5SX2 MCB Based on Siemens Industrial Control Catalog General Data Trip characteristics Tripping characteristics acc. to EN 60 898 Tripping characteristic A, -5 Type A characteristic
More informationSurge protection for telecommunication connections
Surge protection for telecommunication connections White Paper Contents Lightning and surge protection for an analogue connection with ADSL Lightning and surge protection for an ISDN connection with ADSL
More informationic60n RCBO 30 ma IEC , IEC , AS/NZS
ic60n RCBO 30 ma DB405571 Country approval pictograms IEC 61009-1, IEC 61009-2-2, AS/NZS 61009.1 PB110075-70 b The single-phase ic60n RCBO s self-contained residual current device provides protection of
More informationUS CATALOG SMISSLINE TP
US CATALOG SMISSLINE TP 2 SMISSLINE TP US CATALOG SMISSLINE TP US CATALOG 3 Table of contents 004 Description 005 012 for UL 508 and UL 489 based solutions Overview and ordering information 013 014 for
More informationOPTIMISED LUMINAIRE PROTECTION
OPTIMISED LUMINAIRE PROTECTION LUMINAIRE PROTECTION AND POWER ADJUSTMENT This chapter presents inrush current limiters, electronic components to protect luminaires against mains surges, power reduction
More informationTT-SLKK5/ 24DC. Extract from the online catalog. Order No.:
Extract from the online catalog TT-SLKK5/ 24DC Order No.: 2794903 The illustration shows version TT-SLKK5/ 12 DC Modular terminal block with varistor as surge voltage protection between clamping connector
More informationLightning and Surge Protection of Photovoltaic Installations. Leutron GmbH 2013 Leinfelden-Echterdingen, Germany
Lightning and Surge Protection of Photovoltaic Installations 1 Lightning and Surge Protection for PV Installations 2 Safeguard from Risks Ups, that was the insurance policy of my house!! 3 Why Lightning
More informationOTEC Miniature Circuit Breakers (MCB) OTEC Miniature Circuit Breakers (MCB) OTEC Miniature Circuit Breakers (MCB) Areas of Application
Miniature Circuit Breakers Areas of Application Miniature circuit breakers (MCBs) of the N-System primarily protect cables and conductors against overload and short circuit. Thus, they also protect electrical
More informationMessaging module CP-C MM
2CDC 271 087 F0t04 Features Pluggable onto CP C range primary switch mode power supplies REMOTE OFF input to switch off the power supply unit remotely Monitoring of the input voltage of the power supply
More informationOPTIMISED LUMINAIRE PROTECTION
OPTIMISED LUMINAIRE PROTECTION LUMINAIRE PROTECTION AND POWER ADJUSTMENT This chapter presents inrush current limiters, electronic components to protect luminaires against mains surges, power reduction
More information