RTU560. CT/VT Interface 560CVT10. Meter Operation. Application. Characteristics. Data Sheet CT/VT Interface 560CVT10. Instantaneous Meter Values
|
|
- Solomon Craig
- 5 years ago
- Views:
Transcription
1 CT/VT Interface 560CVT10 The fault current is measured up to 20 times nominal current. Therefore the current inputs withstand 50 times nominal current for 1 s. The CT/VT interface is equipped with one binary output which can be used to indicate e.g. alarm for over current. All CT/VT interfaces are mounted in the RTU cabinet. Current and voltage inputs are connected via transformer only (see Figure 1). The CT/VT interfaces are designed for mounting on DIN rails 35 mm. Application The Current/Voltage Transducer Interface (CT/VT interface) is used for measuring analog AC input signals from three independent phases with 3 or 4 wire connections. For each phase voltage, current and power are measured directly, and a number of other parameters derived from these in software. The results are transmitted to the RTU560. There are several versions available: Auxiliary Voltage (LO): 3 current-, 3 voltage inputs (I n 1A) 3 current-, 3 voltage inputs (I n 5A) 4 current-, 4 voltage inputs (I n 1A) 4 current-, 4 voltage inputs (I n 5A) Auxiliary Voltage (HI): 4 current-, 4 voltage inputs (I n 1A) 4 current-, 4 voltage inputs (I n 5A) Characteristics The CT/VT interface is a microprocessorbased Intelligent Electronic Device (IED) intended for current, voltage, power and energy measurement. Distorted input waveforms with harmonics to the 15th are therefore detected accurately. Additional functionality to provide functions as fault current detection, minimum and maximum logging and analog high and low limit supervision is available. Meter Operation The following metered parameters are available: Instantaneous Meter Values Measured by true RMS conversion and transmission to the RTU560 of following values: Phase - Neutral Voltage 1N, 2N, 3N, Average Phase -Phase Voltage 1-2, 2-3, 3-1, Average Current Phase 1, 2, 3 Fault Current Phase 1, 2, 3, N Active Power, Phase 1, 2, 3, Total Reactive Power, Phase 1, 2, 3, Total Apparent Power, Phase 1, 2, 3, Total Power Factor, Phase 1, 2, 3, Average Frequency, Phase Rotation Voltage / Current Harmonic Distortion (THD, current and voltage phase 1,2 and 3) Derived Meter Values calculation of Active, Apparent and Reactive Energy accumulated values (intermediate and end of period readings, delivery and consumption) calculation of Ampere Hours accumulated values (intermediate and end of period readings, delivery and consumption) Neutral current (with 3 wire connection) Doc-No.: 1KGT V
2 Functionalities With a powerful diagnostic tool the operator is able to fulfil below described tasks. As option the related date can be transferred over the communication link to the RTU and the control system. Harmonic analysis for power quality analysis (up to 15th harmonic): Communications over RS485 port with Modbus RTU Protocol User Mapping to speed up communication Logging of Minimum and Maximum Values Relay output for configurable alarm Configurable alarms for over voltage, over frequency, over current and so on Fault current detection (Option) - configurable flexcurve for overcurrent alarm (in the same as IEC, ANSI curves) Event Logging Trend logging (option) Waveform Capturing and phaser analysis: - 2 Doc.-No.: 1KGT V001 1
3 Wiring Fig. 1: 3 phase with 3 wire connection Fig. 2: 3 phase with 4 wire connection Doc-No.: 1KGT V
4 Technical Data In addition to the RTU560 general data, the following applies: Input Channels Voltage U 1, U 2, U 3, U 4 Current I 1, I 2, I 3, I 4 Frequency Samples Range: V AC 3 Phase, 3 or 4 Wire Load : <0.15 VA at 300V U n : - R001x: 3 voltages (U 1, U 2, U 3 ) - R002x, R004x: 4 voltages (U 1, U 2, U 3, U 4 ) R00x5: 5A, max. 6A R00x1: 1A, max. 1.2A Fault current: 20 x In Load: <0.2VA per phase Overload withstand: -2 x In continuous -25 x In 2 s -50 x In 1 s I n : - R001x: 3 current (I 1, I 2, I 3 ) - R002x, R004x: 4 current (I 1, I 2, I 3, I 4 ) Hz 32 samples per cycle Stability Stability Serial Ports Modbus RTU protocol Diagnostic Port Baud Rate Test Voltage Dielectric Strength IEC Immunity Test ANSI / IEEE C IEC Fast Transient / Burst IEC max. 100ppm/ C (Temperature range -10 to +50 C) RS485 RS k, 2.4k, 4.8k, 9.6k, 19.2k bps 2kV AC rms, 1 minute 3 kv SWC Class III SWC Class IV SWC Accuracy Phase I 0.2 % Surge Immunity Test IEC Class IV Impulse Neutral I 0.5 % Phase I, fault current 1 % Phase U 0.2% Auxiliary voltage Auxiliary Voltage (LO) 24/ 48 V DC ±15% Ph-Ph U 0.2% Watts 0.5 % VA 0.5 % Vars 0.5 % PF 0.5 % Auxiliary Voltage (HI) V AC V DC Frequency AD converting 0.05 % rd 12 bit + sign bit 4 Doc.-No.: 1KGT V001 1
5 Mechanical Layout Ordering information Width Height Depth Height Enclosure mm 70.3 mm mm 70.3 mm for DIN Rail 35 mm Environmental Conditions Tempera- Operating ture -25 to +60 ºC Storage Temperature -40 to +80 ºC Relative humidity % non condensing 560CVT10 R00011 In = 1A, 3 voltage, 3 560CVT10 R00015 In = 5A, 3 voltage, CVT10 R0021 I n = 1A, 4 voltage, CVT10 R0025 I n = 5A, 4 voltage, CVT10 R0041 I n = 1A, 4 voltage, 4 current, Version HI 560 CVT10 R0045 I n = 5A, 4 voltage, 4 current, Version HI R0011 R0015 R0021 R0025 R0041 R0045 Doc-No.: 1KGT V
6 Note: We reserve the right to make technical changes or modify the con-tents of this document without prior notice. With regard to purchase orders, the agreed particulars shall prevail. ABB AG does not accept any responsibility whatsoever for potential errors or possible lack of information in this document. We reserve all rights in this document and in the subject matter and illustrations contained therein. Any reproduction, disclosure to third parties or utilization of its contents - in whole or in parts - is forbidden without prior written consent of ABB AG. Copyright 2011 ABB All rights reserved 6 Doc.-No.: 1KGT V001 1
RTU511. Binary Output 23BO62. Characteristics. Application. Data Sheet Binary Output 23BO62. The binary output is made via relay contacts.
Binary Output 23BO62 Characteristics The binary output is made via relay contacts. The 8 outputs are potential isolated against the electronic by optocoupler. All 8 outputs have a separate return. Application
More informationBus Connection Unit 560BCU04
Bus Connection Unit 560BCU04 Application The Bus Connection Unit 560BCU04 R0001 is designed to make the RTU560s TSI, TSO, Alarm and Warning signals accessible to the outside. By using the bus connection
More informationPowerLogic power-monitoring units. Power Meter PM500. Technical data sheet 2006
PowerLogic power-monitoring units Technical data sheet 2006 Functions and characteristics E90463 The PowerLogic PM500 Power Meter provides all measurement capabilities required to monitor an electrical
More informationCharacteristics. Application RTU560. HMI unit 560HMR01. Data Sheet HMI unit 560HMR01
HMI unit 560HMR01 Characteristics Application The 560HMR01 is a rack based human machine interface board of the RTU560 system. The essential tasks of the 560HMR01 are: Interface to RTUs that are running
More informationApplication. Characteristics RTU540. Data Sheet Communication Unit 560CMD11. Communication Unit 560CMD11
Data Sheet Communication Unit 560CMD11 Communication Unit 560CMD11 The SLC works as master for the RTU560 serial peripheral bus (I/O-Interface/ Wired-OR-Bus ). The MPU is responsible for the other tasks.
More informationApplication. Characteristics RTU560. Data Sheet Communication Unit 560CMD11. Communication Unit 560CMD11
Communication Unit 560CMD11 The SLC works as master for the RTU560 serial peripheral bus (I/O-Interface/ Wired-OR-Bus ). The MPU is responsible for the other tasks. The MPU handles the absolute time and
More informationBinary output and supervision 520CSD01 Data sheet
RTU520 product line Binary output and supervision 520CSD01 Data sheet R01 C01 O01 R02 O02 RTU I/O bus ERR Microcontroller RAM Flash IOC Output register DC DC (1 out of n) check Output state monitoring
More informationRTU560 Connections and Settings DIN Rail RTU 560CIG10
Connections and Settings DIN Rail RTU 560CIG10 Application, characteristics and technical data have to be taken from the hardware data sheet: 560CIG10 1KGT 150 719 Operation The 560CIG10 is a DIN rail
More informationData Sheet. Digital Multifunctional Power Meter with LCD Display and Optional Modules WPM D
WPM 770 Data Sheet 679.D.141.02 Digital Multifunctional Power Meter with LCD Display and Application The digital Weigel Power Meters WPM 770 have been designed to display the electrical parameters in low
More informationAnalog output 520AOD01 Data sheet
RTU520 product line Analog output 520AOD01 Data sheet ERR RTU I/O bus Microcontroller RAM Flash Output register DC DC D D A A Adjustment Output range O1 O2 Adjustment Output range IOC UE Figure 1: Block
More informationElectronic timer CT-ARE OFF-delayed without auxiliary voltage, 1 c/o (SPDT) contact
Data sheet Electronic timer CT-ARE OFF-delayed without auxiliary voltage, 1 c/o (SPDT) contact The CT-ARE is an electronic time relay with OFF-delay. It is from the CT-E range. The CT-E range is the economic
More informationElectronic timer CT-SDD.22 Star-delta change-over with 2 n/o contacts
Data sheet Electronic timer CT-SDD. Star-delta change-over with n/o contacts The CT-SDD. is an electronic time relay with star-delta change-over. It is from the CT-D range. With their MDRC profile and
More informationEM132 EM132. Main Features. Multi-functional 3-Phase Transducer. Energy Meter
EM132 MULTI-FUNCTION TRANSDUCER SATEC EM132 is a Smart DIN Rail Multi-Function Transducer with a local display. It is based on SATEC s best seller PM130 PLUS with an off-the-shelf LCD display (similar
More informationUSER MANUAL 2012 V1.1
SMART MINI POWER SDM630 USER MANUAL 2012 V1.1-1 - Installation and Operation Instructions Important Safety Information is contained in the Maintenance section. Familiarise yourself with this information
More informationElectronic timer CT-EBD.12 Flasher starting with ON with 1 c/o (SPDT) contact
Data sheet Electronic timer CT-EBD.12 Flasher starting with ON with 1 c/o (SPDT) contact The CT-EBD.12 is an electronic time relay with the function flasher starting with ON. It is from the CT-D range.
More informationDEIF A/S. MIC Multi-instrument G. Data sheet. Features. Accuracy. Measurements. Installation. Intelligent. Display. Communication DEIF A/S
Multi-instrument 4921210107G Features Measurements All 3-phase AC measurements True RMS Replaces analogue meters Intelligent Suitable for all 3-phase network topologies Replaces transducers Accuracy U,
More informationABB 520BID01 Binary Input datasheet
ABB 520BID01 Binary Input datasheet http://www.manuallib.com/abb/520bid01-binary-input-datasheet.html The binary input module 520BID01 provides 16 galvanic isolated inputs for up to 16 binary process signals.
More informationSwitching relay CT-IRE with 1 c/o (SPDT) contact
Data sheet Switching relay CT-IRE with 1 c/o (SPDT) contact The CT-IRE is a switching relay from the CT-E range. The CT-E range is the economic range of ABB s time relays and offers a cost effective price-performance
More informationC160 Wall-/Pipe Mounted Universal Process Indicator
Data sheet DS/ EN Rev. I Wall-/Pipe Mounted Universal Process Indicator reliable process indicator, wherever it s needed High visibility LED display the clearest view of your process status 0.1% measurement
More informationEngyVolt RV12 and RV15
Technical Information EngyVolt RV12 and RV15 Multifunctional electrical energy meters for top-hat rail installation or panel mounting Application For measuring voltage, frequency, current, power, as well
More informationSDM630M CT USER MANUAL 2016 V4.7. DIN Rail Energy Meter for Single and Three Phase Electrical Systems
SDM630M CT DIN Rail Energy Meter for Single and Three Phase Electrical Systems Measures kwh Kvarh, KW, Kvar, KVA, P, F, PF, Hz, dmd, V, A, THD,etc. Bi-directional measurement IMP & EXP Two pulse outputs
More informationPOWER METER HC Features
Introduction The power quality meter HC 6030 is an ideal device to power monitoring in power quality when continuous monitoring to a power system is required. The HC 6030 provides metering for current,
More informationMIC-2 MKII & MIC-2 MKII DIN, Multi-instrument DATA SHEET
& DIN, Multi-instrument DATA SHEET Measurements All 3-phase AC measurements True RMS 4-Quadrant energy Power Quality Analysis Replaces analogue meters RS-485 Modbus RTU protocol TCP/IP Modbus (optional)
More informationEM-1000 /EM-2000/ EM-3000 Series Multifunction Power and Energy Meters
Power and Energy Meters Code No. LIT-1900845 Issued December 4, 2013 EM-1000 /EM-2000/ EM-3000 Series Multifunction Power and Energy Meters EM-1000 Series Meter Description The EM-1000 Series monitor is
More informationRTU500 series Data Sheet Power Supply CP-E 24/2.5
Data Sheet Power Supply CP-E 24/2.5 Power Supply CP-E 24/2.5 Application The primary switch mode power supply offers two voltage input ranges. This enables the supply with AC or DC. Furthermore it is equipped
More informationAPU 200 Automatic DATA SHEET Gen-set Controller DATA SHEET
APU 200 Automatic DATA SHEET Gen-set Controller DATA SHEET Measurement input, auto range Up to 1000 V AC L-L Up to 12.5 A (sinusoidal) 16 400 Hz Output Up to four analogue outputs Relay output RS 485 Modbus
More informationApplication RTU560 RJ45 RJ45. Management. Switch RJ45 RJ45. Switch 560NMS34 SDSL. Data Sheet Switch 560NMS34. Port 1. Port 2. Port 3.
Switch 560NMS34 Application The RTU component 560NMS34 is a managed plug and play Layer2-switch providing four Fast auto-negotiating RJ45-ports with auto MDI/X (Automatic Crossover Detection and Correction)
More informationElectronic timer CT-ARS.21 OFF-delayed without auxiliary voltage with 2 c/o (SPDT) contacts
Data sheet Electronic timer CT-ARS.21 OFF-delayed without auxiliary voltage with 2 c/o (SPDT) contacts The CT-ARS.21 is an electronic timer from the CT-S range with true OFF-delay. It provides 7 time ranges
More informationMIC-2 MKII, Multi-instrument DATA SHEET
MIC-2 MKII, Multi-instrument DATA SHEET Measurements All 3-phase AC measurements True RMS 4-Quadrant energy Power Quality Analysis Replaces analogue meters RS-485 Modbus RTU protocol TCP/IP Modbus (optional)
More informationSDM120C. Single-Phase Energy Meters. RS485 Modbus RTU. User Manual V1.0
SDM120C Single-Phase Energy Meters RS485 Modbus RTU Measures kwh, Kvarh, KW, Kvar, KVA, PF, Hz, dmd, V, A, etc. Di-directional measurement IMP & EXP Two pulse outputs RS485 Modbus Din rail mounting 17.5mm
More informationString monitoring with CMS - Circuit monitoring system Increased productivity and improved maintenance of PV systems
S O L A R S T R I N G M O N I TO R I N G String monitoring with CMS - Circuit monitoring system Increased productivity and improved maintenance of PV systems Solar plant operators are constantly facing
More informationUser Manual V2.6. SDM120-Modbus. Single-Phase Multifunction DIN rail Meter
SDM120-Modbus Single-Phase Multifunction DIN rail Meter Measures kwh, Kvarh, KW, Kvar, KVA, PF, Hz, dmd, V, A, etc. Bi-directional measurement IMP & EXP Two pulse outputs RS485 Modbus Din rail mounting
More informationFP-5000 Feeder Protection
Effective: April 2001 Page 1 New Information FP-00 Feeder Protection Contents Description Page FP-00 Description......... 2 Application Description...... 2 Features, Functions and Benefits..............
More informationPowerLogic power-monitoring units. PM1000 series power meter. Technical data sheet
PowerLogic power-monitoring units power meter Technical data sheet 2011 Basic energy meters Functions and characteristics PE86261 PE86260 PowerLogic PM1000 power meter. The PowerLogic power meters are
More informationMID PRELIMINARY DATA SHEET. RI-D Series. Single Phase Multifunction Energy Meter (MID Certified) MID
PRELIMINARY DATA SHEET RI-D35-100 Series Single Phase Multifunction Energy Meter (MID Certified) MID direct connected Two pulse outputs LED pulse indication High definition LCD display with white backlight
More informationOHIO SEMITRONICS, INC. AC MULTIFUNCTION PROGRAMMABLE TRANSDUCERS & -1000L
AC PROGRAMMABLE TRANSDUCERS MODBUS OR LONWORKS DESCRIPTION The DMT-1000 is a programmable transducer with an RS-485 bus interface (MODBUS ). It supervises several variables of a poly-phase electrical power
More informationB+G E-Tech User Manual for SDM630 SDM630. Din Rail Smart Energy Meter for Single and Three Phase Electrical Systems USER MANUAL 2013 V1.
SDM630 Din Rail Smart Energy Meter for Single and Three Phase Electrical Systems USER MANUAL 203 V. Important Safety Information is contained in the Maintenance section. Familiarize yourself with this
More informationUser Manual V1.1. SDM120-Modbus(mV) Single-Phase Multifunction DIN rail Meter
SDM120-Modbus(mV) Single-Phase Multifunction DIN rail Meter Measures kwh, Kvarh, KW, Kvar, KVA, PF, Hz, dmd, V, A, etc. Di-directional measurement IMP & EXP Two pulse outputs RS485 Modbus Din rail mounting
More informationCharacteristics. Application RTU560. DIN Rail RTU 560CIG10. Data Sheet DIN Rail RTU 560CIG10
DIN Rail RTU 560CIG10 Application The 560CIG10 is a DIN rail RTU560 consisting of a communication unit (CMU), a multi-i/o module (MIO) and a power supply (PSU) in a metal DIN rail housing. The essential
More informationMIC-2 Multi-instrument DATA SHEET
Measurements All 3-phase AC measurements True RMS 4-Quadrant energy Power Quality Analysis Replaces analogue meters RS-485 Modbus RTU protocol TCP/IP Modbus (optional) Profibus DP (optional) I/O modules
More informationSUBJECT TO CHANGE WITHOUT NOTICE
100A DIRECT CONNECTED (MID CERTIFIED) AP25-3DO www.sifamtinsley.co.uk NEW PRODUCT Multifunction Meters Transducers & Isolators Temperature Controllers Converters & Recorders Digital Panel Meters Current
More informationVoltage monitoring relays CM-ESS.1 For single-phase AC/DC voltages
Data sheet Voltage monitoring relays CM-ESS.1 For single-phase AC/DC voltages The CM-ESS.1 is an electronic voltage monitoring relay that provides reliable monitoring of voltages as well as detection of
More informationElectronic timer CT-ERS.12 ON-delayed with 1 c/o (SPDT) contact
Data sheet Electronic timer CT-ERS.12 ON-delayed with 1 c/o (SPDT) contact The CT-ERS.12 is an electronic timer from the CT-S range with ON-delay and 10 time ranges. All electronic timers from the CT-S
More informationElectronic timer CT-SDS.23 Star-delta change-over with 2 n/o contacts
Data sheet Electronic timer CT-SDS. Star-delta change-over with n/o contacts The CT-SDS. is an electronic timer from the CT-S range with Star-delta change-over and 7 time ranges. All electronic timers
More informationEnergy Management Modular DC Energy analyzer Type VMU-E and VMU-X
Energy Management Modular DC Energy analyzer Type VMU-E and VMU-X Modular solution based on the combination of two units: VMU-E analysis unit and VMU-X universal power supply and RS485 communication unit.
More informationDigital Multifunction Meters. Digital Multifunction Meters
Digital Multifunction Meters Digital Multifunction Meters DIGITAL MULTIFUNCTIOL METERS SECTION INDEX 1. MFM 3410 3420 3430 3440 6100 & 2000 - Multifunctional Instrument Series 2. EM 3490, 3490SS, 3490DS
More informationABB i-bus KNX HCC/S Heating/cooling circuit controller
ABB i-bus KNX HCC/S 2.2.1.1 Heating/cooling circuit controller Description of product The device is a modular DIN rail component (MDRC) in pro M design. It is intended for installation in distribution
More informationApplication. Characteristics RTU560. DIN Rail RTU 560CIG10. Data Sheet DIN Rail RTU 560CIG10
DIN Rail RTU 560CIG10 MPU: 32 Bit Main Processing Unit SLC: 8 Bit Serial Line Controller I/O: 8 Bit In/Out Micro Controller The SLC works as master for the RTU560 serial peripheral bus (Wired-OR-Bus).
More informationPower and accuracy. Versatile. One display can monitor up to 32 measuring modules information
Power and accuracy 0.2% or 0.5% class in power and active energy measurement Over 500 electric parameters display Both voltage and current harmonics spectrum graphics (to the 50 th ) Maximum and minimum
More informationWM20. Power analyzer for three-phase systems. Benefits. Description
WM20 Power analyzer for three-phase systems Description WM20 is a modular power analyzer for single-, two- and three-phase systems. It is made up of a maximum of three components: the main unit that displays
More informationElectronic timer CT-ARS.11 OFF-delayed without auxiliary voltage with 1 c/o (SPDT) contact
Data sheet Electronic timer CT-ARS.11 OFF-delayed without auxiliary voltage with 1 c/o (SPDT) contact The CT-ARS.11 is an electronic timer from the CT-S range with true OFF-delay. It provides 7 time ranges
More informationData sheet ACT20P ACT20P-CMT-10-AO-RC-S. Phone: Fax: Web: - [!
-CMT-10-AO-RC-S [!-] General ordering data Type -CMT-10-AO-RC-S Order No. 1510470000 Version Current-measuring transducer GTIN (EAN) 4050118319583 Qty. 1 pc(s). -CMT-10-AO-RC-S Technical data Dimensions
More informationDIN Rail Smart Meter for Single and Three Phase Electrical Systems
SDM630-Modbus V2 DIN Rail Smart Meter for Single and Three Phase Electrical Systems Measures kwh Kvarh, KW, Kvar, KVA, P, F, PF, Hz, dmd, V, A, etc. Bi-directional measurement IMP & EXP Two pulse outputs
More informationEM133 EM133 TOU SMART ENERGY METER. Main Features. Multifunctional 3-Phase Smart Meter. Billing/TOU Energy Meter
TOU SMART ENERGY METER SATEC is a Smart DIN Rail TOU Energy Meter. It is based on SATEC s best seller PM130 PLUS with an off-theshelf LCD display (similar to the BFM136 display). The provides the full
More informationEPM g Energy. Multilin BUILDING AUTOMATION POWER METER. BACnet /IP Communications and Energy Measurement KEY BENEFITS APPLICATIONS FEATURES
Multilin EPM 6010 BUILDING AUTOMATION POWER METER BACnet /IP Communications and Energy Measurement KEY BENEFITS Rapid integration into BACnet management systems High accuracy multifunction power meter,
More informationPower Meter PowerMonitor 500
ROCKWELL AUTOMATION PROCUREMENT SPECIFICATION PROCUREMENT SPECIFICATION PowerMonitor 500 NOTICE: The specification guidelines in this document are intended to aid in the specification of products. Specific
More informationDIN Rail RTU 540CMD01 Data sheet
RTU540 product line DIN Rail RTU 540CMD01 Data sheet 4 3 RS232C RS232C RS232C or RS485 or RS485 or RS485 1 2 E1 E2 10/100 MB LAN Protocol Protocol Controller Controller MPU Cortex-A8 AM3352 Application
More informationMultilin EPM 6010 YEAR. GE Grid Solutions. Building Automation Power Meter with BacNET /IP Communications. Monitoring & Metering
GE Grid Solutions Multilin EPM 6010 Building Automation Power Meter with BacNET /IP Communications The Multilin EPM 6010 is an industry leading revenue grade power meter with native BACnet/ IP communications.
More informationPM130 PLUS PM130 PLUS POWER METER. Features. Models. Multifunctional 3-phase Power Meter
PM130 PLUS POWER METER The PM130 PLUS is a compact, multi-function, three-phase AC powermeter specially designed to meet the requirements of users ranging from electrical panel builders to substation operators.
More informationDigital Indicator DS 48/24 E
Data Sheet 10/33-2.04-EN Digital Indicator DS 48/24 E The indicator is suitable for measuring direct voltage or direct current. The units are installed in a rugged plastic housing and can be integrated
More informationINDI BOY DSP Load limitation electronics
Change from one to two columns Data Sheet DS/INDI-BOY-DSP-EN Rev. A INDI BOY DSP Load limitation electronics Load limitation with 3 set points and display to be installed on a front panel Measurement made
More informationSDM530-Modbus USER MANUAL 2015 V1.5. Three Phase Multi-function DIN rail meter. Eastron SDM530-Modbus User Manual
SDM530-Modbus Three Phase Multi-function DIN rail meter Measures kwh Kvarh, KW, Kvar, KVA, P, F, PF, Hz, dmd, V, A, etc. Bi-directional measurement IMP & EXP Two pulse outputs RS485 Modbus Din rail mounting
More informationMessaging module CP-C MM
2CDC 271 087 F0t04 Features Pluggable onto CP C range primary switch mode power supplies REMOTE OFF input to switch off the power supply unit remotely Monitoring of the input voltage of the power supply
More informationMW/MVAR Transducer Specifications
GUARANTEED TECHNICAL PARTICULARS (To be submitted by bidder with the tender) MW/MVAR Transducer Specifications Sr.No. Descriptions Details Offered by supplier 1 2 3 4 Transducer suitable for Input Output
More informationAP25-1DO METER (MID CERTIFIED) User Manual - Issue 1.0
(MID CERTIFIED) AP25-1DO www.sifamtinsley.co.uk NEW PRODUCT Multifunction Meters Transducers & Isolators Temperature Controllers Converters & Recorders Digital Panel Meters Current Transformers Analogue
More informationThree-phase electricity meter with instantaneous reading of electrical variables. Input current measurement: 5 A, 90 A, 150 A, 250 A (span by model).
SCEE AR 3 - Smart Analyzer 485/Ethernet with web visualization Three-phase electricity meter with instantaneous reading of electrical variables. System variables: V, A, kw, kva, kvar, PF and Hz. Variables
More informationEnergy Management Modular DC Energy analyzer Type VIM-E and VIM-X
Energy Management Modular DC Energy analyzer Type VIM-E and VIM-X Modular solution based on the combination of two units: VIM-E analysis unit and VIM-X universal power supply and RS485 communication unit.
More informationABB i-bus KNX BCI/S Boiler/Chiller Interface
ABB i-bus KNX BCI/S 1.1.1 Boiler/Chiller Interface Description of product The boiler/chiller interface is a modular DIN rail component that acts as an interface to the heating/cooling system generator.
More informationVoltage Transducer UMT516 / MT516
Voltage Transducer UMT516 / MT516 True RMS AC voltage measurements Voltage auto range measurements up to 600V # Wide frequency measurement range 16 400 Hz High accuracy class 0.2 (IEC-688), 0.1 on communication
More informationwith Backlight Graphic LCD Screen
with Backlight Graphic LCD Screen ENERGY AND AUTOMATION POWER OF ENERGY SAVING For the control of energy distribution systems detecting when problems occur that could put the quality and availability of
More informationEnergy Management Energy Transducer Type ET112
Energy Management Energy Transducer Type Single phase energy transducer Class 1 (kwh according to EN62053-21 Class B (kwh according to EN50470-3 Accuracy ±0.5% RDG (current/voltage Direct current measurement
More informationUMG 604. UMG 604 Power analyser. Modbus master, Ethernet gateway. Harmonics. Memory 128 MByte. Homepage. Graphic programming.
Harmonics Modbus master, Ethernet gateway Memory 128 MByte Homepage Events Graphic programming UMG 604 Power analyser Communication Profibus (DP/ V0) Modbus (RTU, UDP, TCP, Gateway) TCP/IP BACnet (optional)
More informationSDM530CT-Modbus USER MANUAL 2015 V1.6. Three Phase Multi-function DIN rail meter. Eastron SDM530CT-Modbus User Manual
SDM530CT-Modbus Three Phase Multi-function DIN rail meter Measures kwh Kvarh, KW, Kvar, KVA, P, F, PF, Hz, dmd, V, A, etc. Bi-directional measurement IMP & EXP Two pulse outputs RS485 Modbus Din rail mounting
More information4 Is this model available for special primary current and special primary voltage?
Category: Sales 1 Is it possible to exchange the backlights? The backlights are LED, no need to exchange. Fukuyama Works, Mitsubishi Electric Corporation March, 2018 2 Which standards does this model support?
More informationMultifunction Transducer MT440
Multifunction Transducer MT440 Voltage and current auto range measurements up to 600V, 12.5A Universal wide auxiliary power supply range 24 300 Vdc, 40 276 Vac Power accuracy class 0.5 (EN 60 688), Up
More informationEnergy Monitoring Solutions
Monitoring Solutions More eff iciency than you expected The Fundamentals Def ining an energy analyzer in simple terms An energy analyzer provides highly accurate measuring for main electrical and Metering
More informationDRTS 3 PLUS. Advanced Protection Relay Test Set and Measurement System. DRTS 3 PLUS has been designed to test:
Advanced Protection Relay Test Set and Measurement System Multi-tasking equipment designed for testing protection relays, energy meters, transducers Particularly designed to test RTU (remote terminal unit)
More informationSACE Emax 2 Specification guide
SACE Emax 2 Specification guide Specification Number: 26 01 20.17 Product Name: LOW VOLTAGE POWER CIRCUIT BREAKERS PART 1 GENERAL NOTE: ( ) Indicates option or a selection is to be made for quantity or
More informationDIGITAL TEMPERATURE MONITOR MASTERTEMP ANSI I CATALOG
CATALOG INTRODUCTION The temperature monitor MASTERTEMP was developed to monitor oil and winding temperatures in transformers and reactors immersed in oil. It features also the activation of cooling fans
More informationSEL-734B Data Sheet. Advanced Monitoring and Control System. Major Features and Benefits
Advanced Monitoring and Control System Compact Enclosure Full-Size Enclosure Major Features and Benefits The SEL-734B combines volt/var based capacitor bank control with power quality monitoring and advanced
More informationEM6400 series Multi-Function meters
6400 series Multi-Function meters 1 Digital display & Analog load bar indicators 2 Bright Red LED display 3 Global: CE, UL marks 4 Universal Demand Monitoring Quick and easy installation Turbo Key 6400
More informationPM800 series. Applications
Functions and characteristics PE86134 The PowerLogic meters offers many high-performance capabilities needed to meter and monitor an electrical installation in a compact 96 x 96 mm unit. All models include
More informationPM174 PM174 IEEE1159 ADVANCED POWER QUALITY ANALYZER. Features
PM174 IEEE1159 ADVANCED POWER QUALITY ANALYZER The PM174 is a compact, multi-function, three-phase AC powermeter and power quality analyzer specially designed to meet the requirements of users ranging
More informationABB SACE A division of ABB S.p.A. L.V. Breakers Via Pescaria 5, Bergamo - Italy Phone: Fax:
ABB SACE A division of ABB S.p.A. L.V. Breakers Via Pescaria 5, 24123 Bergamo - Italy Phone: +39 035 395.111 Fax: +39 035 395.306-433 abb.com/lowvoltage Copyright 2017 ABB. All rights reserved. Specifications
More informationBFM-II BFM-II BRANCH FEEDER MONITOR. Highlights
BRANCH FEEDER MONITOR SATEC s is the second generation of Branch Feeder Monitor, providing energy management for multi-point power solutions. Ideal for both new and retrofit projects, the automatically
More informationNEMO HD MULTI-FUNC METER BASE (MF96001)
NEMO HD MULTI-FUNC METER BASE (MF96001) Quick and easy to install Compact modern design High accuracy monitoring and measurement to IEC 62053-21 Easy to read and configure Options for remote communication
More informationENhanced TEChnology. Solid insulated vacuum recloser for power distribution system thru 15kV, 27kV, 38kV. Ver.
ENhanced TEChnology www.entecene.co.kr Solid insulated vacuum recloser for power distribution system thru 15kV, 27kV, 38kV Ver. 081226 General features We, ENTEC introduce a Solid Insulated Vacuum Recloser
More informationMultilin EPM Energy and Demand Submeter with Wi-Fi. Monitoring & Metering. Communications. Key Benefits. Applications
Multilin EPM 6100 Energy and Demand Submeter with Wi-Fi The EPM 6100 is a powerful tool that allows customers to monitor and manage their energy usage within factories, businesses and across campuses.
More informationEnergy Management BUS Adapter Type VMU-B 01
Energy Management BUS Adapter Type VMU-B 01 RS485 (Modbus) to M-Bus communication adapter EM21-72D, EM24-DIN and EM33-DIN self recognition Front diagnostic LED s Universal 18 to 260 VAC/DC power supply
More informationST 200 M data sheet System pro M compact miniature circuit breakers for supplementary protection acc. to UL 1077
MINIATURE CIRCUIT BREAKERS ST 200 M data sheet System pro M compact miniature circuit breakers for supplementary protection acc. to UL 1077 The ST 200 M miniature circuit breaker provides supplementary
More informationPowerLogic power-monitoring units. EM1000 series power meter. Technical data sheet
PowerLogic power-monitoring units power meter Technical data sheet Distributed By: MetersUSA www.metersusa.com Meters@MetersUSA.com 1 224 365 5935 Basic energy meters Functions and characteristics PB105460
More informationPen Drive USB Datalogger!
SINGLE PHASE POWER METER Isolated V/I converter -RS485 Modbus - Datalogger Single-phase power meter RMS, and Voltage/Current Isolated. Signal Converter 1000 VDC / 600 VAC, 10 A AC/DC, Variable frequency
More informationEnergy Management Modular Universal Utility Meter and Power Analyzer Type WM24-96
Energy Management Modular Universal Utility Meter and Power Analyzer Type WM24-96 Class 1 (active energy) Class 2 (reactive energy) Accuracy 0.5% RDG (current/voltage) Universal utility meter and power
More informationRT4F-48V/50A-WAC RECTIFIER
The RT4F-48V/50A-WAC is a switched mode rectifier (SMR) module designed to provide up to 58A of output current into a 48V nominal system, over a wide range of AC input voltage. This rectifier has been
More informationS1MMmA500VM S1MMmA500VLM S1MMmA500VHM. Technical data. 3-phase energy meter with universal current input
3-phase energy meter with universal current input Equivalent to class 0,5S (KWh) of E6053- Equivalent to class 0,5S (KVARh) of E6053-4 Accuracy ±0,5% RDG Universal input for current measurement Energy
More informationMehta Tech, Inc. TRANSCAN IED For Multi-Function, Multi-Speed Recording
Mehta Tech, Inc. TRANSCAN IED For Multi-Function, Multi-Speed Recording Two independent, simultaneously operating recorders in one package Triggering on input quantities and calculated values, such as
More informationNPW800R RETROFITTING. Power and Volatge Protection Relay
RETROFITTING Power and Volatge Protection Relay NPW800R (R3 case) is dedicated to the refurbishment of CEE WTG 7000 relays (R3 case) providing the measurement of apparent (S), active (P) and reactive (Q)
More informationRedundancy unit CP-D RU Accessory for CP range power supplies (e.g. switch mode power supplies CP-D range)
Data sheet Redundancy unit Accessory for CP range power supplies (e.g. switch mode power supplies CPD range) The provides decoupling of two power supply units and ensures automatic redundant power supply
More informationINTEGRA DIGITAL METERING SYSTEMS
CROMPTON INSTRUMENTS INTEGRA DIGITAL METERING SYSTEMS INTEGRA DIGITAL METERING SYSTEMS The Integra digital metering product portfolio offers an extensive range of systems designed to suit any power monitoring
More informationDRTS 3 PLUS Advanced Protection Relay Test Set and Measurement System
Advanced Protection Relay Test Set and Measurement System Multi-tasking equipment designed for testing protection relays, energy meters, transducers Particularly designed to test RTU (remote terminal unit)
More information