USB-16COMi-M 16-Port RS-422/485 USB Serial Adapter User Manual. Features and Specifications. Power Supply

Transcription

1 USB-16COMi-M 16-Port RS-422/485 USB Serial Adapter User Manual The USB to industrial 16-Port RS-422/485 Adapter is designed to make serial port expansion quick and simple. Connecting to a USB port on your computer or USB hub, the USB Serial Adapter instantly adds 16 RS-422/485 multi-electrical interface serial communication ports to your system. By taking advantage of the USB bus, the USB-16COMi-M Adapter makes it easier than ever to add 16 RS-422/485 ports and serial devices to your system with easy plug-and-play and hot plug features. Adapting the new technology, the serial port expansion now takes the new bus with easy and convenient connectivity. USB-16COMi-M Plugging the USB 16-Port RS-422/485 Adapter to the USB port, the adapter is automatically detected and installed. There are no IRQ & COM port conflicts, since the port doesn't require any additional IRQ, DMA, memory as resources on the system. The RS-422/485 port functions as native Windows COM port, and it is compatible with Windows serial communication applications. Each port is individually configurable. The adapter is designed with external switches to set the RS-422 or RS-485 ports and different operation modes conveniently. There is no need to open the chassis to set the ports. The USB Serial Adapter provides instant connectivity to RS-422 or RS-485 communication devices for factory automation equipment, multi-drop data collection devices, barcode readers, time clocks, scales, data entry terminals, ATMs and serial communication in harsh environment. The USB to Serial Adapter is suitable for remote access, retail and industrial application, data collection and other applications requiring high speed RS-422/485, communication ports. Features and Specifications Adds sixteen high speed RS-422 / 485 serial ports via USB connection. 384 byte receive buffer. 128 byte transmit buffer for high speed data throughput. Requires no IRQ, DMA, I/O port. Data rates: 300 bps to 921.6K bps. Serial Connector: one DB-9 male connector. Auto transmit buffer control for 2-wire RS-485 half-duplex operation. Termination resistors installed on-board. RS-422 data signals: Tx-, Tx+, Rx+, Rx-, GND, RTS-, RTS+, CTS+, CTS-. RS-485 data signals: Tx-, Tx+, Rx+, Rx-(4 wire) and data-, data+ (2 wire). Monitor LEDs of TxD, RxD indicating port status. AC 100V 240V input for DC 5V, 4A switching power supply. Virtual COM port drivers available for Windows 7, Vista, 2003, XP, Power Supply Input: AC 100V ~ 240V, Hz. Output: DC 5.0V 4A.

2 Hardware Installation Outside the unit, there are sixteen 3-pin DIP switches which are set to select the mode of operation. You will need to set the switch settings to RS-422 or RS-485 mode as per the requirements of your application. You need to install driver first, prior to hardware installation. After the setting of DIP switches and connecting power cord to the adapter, you then plug the adapter to USB port to start driver installation. Mode Block Configuration Settings SW1 (Port-1), SW2 (Port-2), SW3 (Port-3), SW4 (Port-4) SW5 (Port-5), SW6 (Port-6), SW7 (Port-7), SW8 (Port-8) SW9 (Port-9), SW10 (Port-10), SW11 (Port-11), SW12 (Port-12) SW13 (Port-13), SW14 (Port-14), SW15 (Port-15), SW16 (Port-16) Operation Mode S1 S2 S3 RS wire with handshaking ON ON ON RS-485 Full Duplex (4 wire) OFF ON ON Half Duplex (2 wire) with Echo OFF OFF ON Half Duplex (2 wire) without Echo OFF OFF OFF JP5 (Port-1), JP6 (Port-2), JP7 (Port-3), JP8 (Port-4) JP9 (Port-5), JP10 (Port-6), JP11 (Port-7), JP12 (Port-8) JP13 (Port-9), JP14 (Port-10), JP15 (Port-11), JP16 (Port-12) JP17 (Port-13), JP18 (Port-14), JP19 (Port-15), JP20 (Port-16) for Termination and Biasing Option Configuration Inside the unit, there are sixteen 2 x 7 (14 pin) header blocks which are jumpered to enable Tx, Rx, CTS 120 Ohm termination resistors and Tx, Rx 750 Ohm BIASing resistor. You will need to open up the metal case and set the jumper setting for RS-422 mode or RS-485 mode as per the requirements of your application. Settings are listed as follows: Jumper Function 1-2 Tx+/- Termination of 120 Ohm. This jumper should always be populated for RS485 mode. 3-4 Pull-up Tx+ to VCC by 750 Ohm Bias resistor. This jumper should be populated for pull-up Tx Pull-down Tx- to GND by 750 Ohm Bias resistor. This jumper should be populated for pull-down Tx Rx Termination of 120 Ohm. This jumper should always be populated for RS-422 mode Pull-up Rx+ to VCC by 750 Ohm Bias resistor.

3 This jumper should be populated for pull-up Rx Pull-down Rx- to GND by 750 Ohm Bias resistor. This jumper should be populated for pull-down Rx CTS Termination of 120 Ohm. This jumper should always be populated for RS-422 mode. Note: Sometimes, when operating in RS-422 or RS-485, it is necessary to configure termination and biasing of the data transmission lines. Generally this must be done in the cabling, since this depends on the installation of connections. Before applying the option, check your cable specification for proper impedance matching. Windows 7/ Vista / 2003 / XP / 2000 Driver Installation You need to have administrator privileges to install any new drivers under Windows 7/ Vista / 2003/ XP / To install the driver or update the configuration please log onto Windows as "Administrator" or ask your system administrator to install the USB-COM driver. Note: You need to install the driver first, prior to hardware installation. Do not connect the USB-to-Serial Adapter to the USB port of your computer, before you finish driver installation. Please proceed with the following steps to install the driver: 1. Insert the USB COM Series Driver and Utility CD into your CD-ROM. 2. The USB COM Series Driver and Utility CD dialog box appears. 3. Under Driver Installation, double click Windows 7, Vista, 2003, XP, 2000 driver to install the device driver. 4. The USB COM install program will auto-detect the OS type and install the driver automatically. (Note: in Windows 7 or Vista OS you will find another dialog box, please click on OK to confirm the drivers install program). 5. After the message FTDI CDM Driver installation process completed appears, press Enter to complete the driver installation. 6. Plug in the USB to Serial Adapter to the USB port of your computer. Windows will finish installing the driver files. Check Installation You can now verify the installation has been completed successfully by looking under Device Manager of the System Properties screen. (Go there by Start-Setting- Control Panel-System Properties-Hardware-Device Manager.

4 The device should have installed as a "USB Serial Port (COMx)" attached to "USB Serial Converter (A/B or A/B/C/D)". Change COM Port Properties & COM Port Number This feature is particularly useful for programs, such as HyperTerminal, which only work with COM1 through COM4. Please ensure that you do not change the COM Port Number already in use. To change the virtual COM port properties: Select the "USB Serial Port" Click Properties. Select "Port Setting" and Advanced. Click the drop down arrow on COM Port Number and scroll to the required COM port. Select "OK". Return to the Device Manager Screen. You will see that the USB Serial Port installation has been changed to the new COM Port Number. Uninstalling Windows 2003/XP/2000 Drivers Please proceed with the following steps to uninstall the 2003/XP/2000 driver: 1. Insert the USB COM Series Driver and Utility CD into your CD-ROM. 2. The USB COM Series Driver and Utility CD dialog box appears. 3. Under Driver uninstalling, double click Windows 2003, XP, 2000 driver uninstall to uninstall the device driver. 4. When following dialog box appears, double click Clean System to uninstall the 2003/XP/2000 drivers. 5. You need to disconnect all USB to serial Adapters from your PC, when the message below appears. Double click OK to start uninstalling Windows 2003/XP/2000 USB to Serial drivers.

5 6. Double click Yes to confirm it. 7. Click No to proceed. 8. When the message Status: System clean completed appears, double click Exit to complete the USB to serial drivers uninstall.

6 9. Press Start button and select Control Panel. 10. Open the Add or Remove program. 11. Remove the first Windows Driver Package FTDI CDM Driver Package ( ). 12. Click Chang/Remove and Yes to remove the first Windows Driver Package. 13. Remove the second Windows Driver Package FTDI CDM Driver Package ( ). 14. Click Change/Remove and Yes to remove the second Windows Driver Package. 15. Reboot the computer to complete the driver uninstall. Uninstalling Windows 7 or Vista Drivers Windows 7 and Vista have many new security features. You need to proceed with the following steps to uninstall the Vista driver: 1. The USB to serial devices must connect to the PC. 2. Press Start button and select Control Panel. 3. Select Classic View from the top left hand corner and then System from the list. 4. Select Device Manager from the top left hand corner.

7 5. Locate your Device under the Ports (COM & LTP) section and right click on it to bring up the menu shown. 6. Select uninstall and be sure to click the box for Delete the driver software for this device in the next window and press OK.

8 Note: if you have more than one USB Serial Port (COMx) installed in your PC, you need to repeat from step 5 to step 6 to delete the driver software for each port. 7. Locate your Device under the Universal Serial Bus Controllers section, and right click on it to bring up the menu shown. 8. Select uninstall and be sure to click the box for Delete the driver software for this device in the next window and press OK. Note: if you have more than one USB Serial Converter installed in your PC, you need to repeat step 7 and step 8 to delete the driver software for all devices.

9 RS-422 Signal Pin-outs of DB-9 Male (CN2, CN3) Pin 1 Pin 2 Pin 3 Pin 4 Pin 5 Pin 6 Pin 7 Pin 8 Pin 9 TxD- (A) TxD+ (B) RxD+ (B) RxD- (A) GND RTS- (A) RTS+(B) CTS+(B) CTS- (A) RS-422 Signal Wiring Point-to-Point 4 Wire Full Duplex USB-16COMi-M RS-422 Device 2 TxD+ (B) RxD+ (B) 1 TxD- (A) RxD- (A) 3 RxD+ (B) TxD+ (B) 4 RxD- (A) TxD- (A) 5 GND GND RS-422 with Handshaking USB-16COMi-M RS-422 Device 2 TxD+ (B) RxD+ (B) 1 TxD- (A) RxD- (A) 3 RxD+ (B) TxD+ (B) 4 RxD- (A) TxD- (A) 5 GND GND 7 RTS+ (B) CTS+ (B) 6 RTS- (A) CTS- (A) 8 CTS+ (B) RTS+ (B) 9 CTS- (A) RTS- (A) RS Wire (Full Duplex) Signal Pin-outs of DB-9 Male Pin 1 Pin 2 Pin 3 Pin 4 Pin 5 Tx- (A) Tx+ (B) Rx+ (B) Rx- (A) GND

10 RS Wire (Half Duplex) Signal Pin-outs of DB-9 Male Pin 1 Pin 2 Pin 5 Data- (A) Data+ (B) GND RS-485 Signal Wiring Point-to-Point 4 Wire Full Duplex USB-16COMi-M RS-485 Device 2 TxD+ (B) RxD+ (B) 1 TxD- (A) RxD- (A) 3 RxD+ (B) TxD+ (B) 4 RxD- (A) TxD- (A) 5 GND GND Multi-drop RS Wire Half-duplex