Output Voltage Range. Power ma ma 700 ma 176~305 Vac 97~214 Vdc 150 W 93.0% 0.98 EBD-150S105DVA

Transcription

1 EBD150SxxxDVA Features Ultra High Efficiency (Up to 93.0%) Full Power at Wide Output Current Range (Constant Power) Compact Package Design 05V/010V/PWM/Timer Dimmable Input surge protection: 6 kv lineline, 10 kv lineearth AllAround Protection: OVP, SCP, OTP Waterproof (IP67) SELV Output Suitable for Independent Use Description The EBD150SxxxDVA series is a 150W, constantcurrent, programmable LED driver that operates from Vac input with excellent power factor. It is created for high bay, tunnel and roadway lights. The high efficiency of these drivers and compact metal case enables them to run cooler, significantly improving reliability and extending product life. To ensure troublefree operation, protection is provided against input surge, output over voltage, short circuit, and over temperature. Models Output Current Range FullPower Current Range (1) Default Output Current Input Voltage Range(2) Output Voltage Range Max. Typical Output Efficiency Power (3) Power Factor (3) Model Number ma ma 700 ma 176~305 Vac 97~214 Vdc 150 W 93.0% 0.98 EBD150S105DVA ma ma 2800 ma 176~305 Vac 24~53 Vdc 150 W 93.0% 0.98 EBD150S420DVA (4) Notes: (1) Output current range with constant power at 150W (2) CCC certified input voltage range: 220/230/240 Vac; Other certified input voltage range except CCC: Vac (3) Measured at full load and 220Vac input (see below General Specifications for details). (4) SELV output IV Operation Area EBD150S105DVA EBD150S420DVA 1 / 11 Tel: Fax: sales@inventronicsco.com

2 EBD150SxxxDVA Input Specifications Parameter Min. Typ. Max. Notes Input Voltage 176 Vac 305 Vac Input Frequency 47 Hz 63 Hz Leakage Current 0.70 ma IEC605981; 240Vac/ 60Hz Input AC Current 0.82 A Measured at full load and 220 Vac input. Inrush Current(I 2 t) 2.40 A 2 s PF 0.9 THD 20% At 220Vac input, 25 cold start, duration=984 us, 10%Ipk10%Ipk. See Inrush Current Waveform for the details. At Vac, 65%100% Load (98150W) Output Specifications Parameter Min. Typ. Max. Notes Output Current Tolerance 5%Ioset 5%Ioset At full load condition Output Current Setting(Ioset) Range EBD150S105DVA EBD150S420DVA Output Current Setting Range with Constant Power EBD150S105DVA EBD150S420DVA Total Output Current Ripple (pkpk) Output Current Ripple at < 200 Hz (pkpk) 70 ma 280 ma 700 ma 2800 ma 1050 ma 4200 ma 1050 ma 4200 ma 5%Iomax 10%Iomax At full load condition, 20 MHz BW 2%Iomax Startup Overshoot Current 10%Iomax At full load condition At full load condition. Only this component of ripple is associated with visible flicker. No Load Output Voltage EBD150S105DVA EBD150S420DVA 231 V 60 V Line Regulation ±0.5% Measured at full load Load Regulation ±1.5% Turnon Delay Time 0.6 s 1.5 s Measured at 220Vac input. Temperature Coefficient 0.03%/ C Case temperature = 0 C ~Tc max 12V Auxiliary Output Voltage 10.8 V 12 V 13.2 V 12V Auxiliary Output Source Current 0 ma 20 ma Return terminal is Dim Note: All specifications are typical at 25 C unless otherwise stated. 2 / 11 Tel: Fax: sales@inventronicsco.com

3 EBD150SxxxDVA General Specifications Parameter Min. Typ. Max. Notes Efficiency at 220 Vac input: EBD150S105DVA Io=700 ma Io=1050 ma EBD150S420DVA Io=2800 ma Io=4200 ma 91.0% 90.5% 91.0% 89.0% MTBF Lifetime Operating Case Temperature for Safety Tc_s Operating Case Temperature for Warranty Tc_w 93.0% 92.5% 93.0% 91.0% 305, 000 Hours 95,500 Hours 40 C +90 C 40 C +70 C Measured at full load and steadystate temperature in 25 C ambient; (Efficiency will be about 2.0% lower if measured immediately after startup.) Measured at 220Vac input, 80%Load and 25 C ambient temperature (MILHDBK 217F) Measured at 220Vac input, 80%Load and 60 C case temperature; See lifetime vs. Tc curve for the details Storage Temperature 40 C +85 C Humidity: 5%RH to 100%RH Dimensions Inches (L W H) Millimeters (L W H) Net Weight 1050 g Note: All specifications are typical at 25 C unless otherwise stated. Dimming Specifications With mounting ear Parameter Min. Typ. Max. Notes Absolute Maximum Voltage on the Vdim (+) Pin 20 V 20 V Source Current on Vdim (+)Pin 200 ua 300 ua 450 ua Vdim(+) = 0 V Dimming Output Range EBD150S105DVA EBD150S420DVA EBD150S105DVA EBD150S420DVA Recommended Dimming Range for 05V Recommended Dimming Range for 010V 10%Ioset Ioset 70 ma 280 ma Ioset 700 ma Ioset 1050 ma 2800 ma Ioset 4200 ma 70 ma Ioset 700 ma 280 ma Ioset 2800 ma 0 V 5 V Dimming mode set to 05V in PC interface. 0 V 10 V PWM_in High Level 3 V 10 V Default 010V dimming mode with positive logic. PWM_in Low Level 0.3 V 0.6 V PWM_in Frequency Range 200 Hz 2 KHz Dimming mode set to PWM in PC interface. PWM_in Duty Cycle 1% 99% 3 / 11 Tel: Fax: sales@inventronicsco.com

4 EBD150SxxxDVA Safety &EMC Compliance Safety Category Standard CE EN , EN CCC GB , GB KS KS C 7655 : 2011 EMI Standards EN 55015/GB (1) EN /GB EN EMS Standards EN EN EN Notes Conducted emission Test &Radiated emission Test Harmonic current emissions Voltage fluctuations & flicker Notes Electrostatic Discharge (ESD): 8 kv air discharge, 4 kv contact discharge RadioFrequency Electromagnetic Field Susceptibility TestRS Electrical Fast Transient / BurstEFT EN Surge Immunity Test: AC Power Line: line to line 6 kv, line to earth 10 kv (2) EN EN EN Conducted Radio Frequency Disturbances TestCS Power Frequency Magnetic Field Test Voltage Dips EN Electromagnetic Immunity Requirements Applies To Lighting Equipment Note: (1) This LED driver meets the EMI specifications above, but EMI performance of a luminaire that contains it depends also on the other devices connected to the driver and on the fixture itself. (2) To perform electric strength (hipot) testing, the GDT ground disconnect (screw and metal lock sheet) on the driver endcap should be removed temporarily to prevent the internal gas discharge tube from conducting (as allowed by IEC Clause 10.2). After testing is completed, these items must be reinstalled to restore linetoearth surge protection and secure the end cap. Lifetime vs. Case Temperature 4 / 11 Tel: Fax: sales@inventronicsco.com

5 EBD150SxxxDVA Inrush Current Waveform Efficiency vs. Load EBD150S105DVA(Io=700mA) EBD150S105DVA(Io=1050mA) EBD150S420DVA(Io=2800mA) EBD150S420DVA(Io=4200mA) 5 / 11 Tel: Fax: sales@inventronicsco.com

6 EBD150SxxxDVA Power Factor Total Harmonic Distortion Protection Functions Parameter Over Temperature Protection Short Circuit Protection Over Voltage Protection Notes Auto Recovery. The output shall return to normal when over temperature is removed. Auto Recovery. No damage will occur when any output is short circuited. The output shall return to normal when the fault condition is removed. Limits output voltage at no load and in case the normal voltage limit fails. Dimming 05V Dimming The recommended implementation of the dimming control is provided below. 6 / 11 Tel: Fax: sales@inventronicsco.com

7 EBD150SxxxDVA Implementation 1: Positive logic Implementation 2: Negative logic Notes: 1. The dimmer can also be replaced by an active 05V voltage source signal or passive components like resistors and zener. 2. Do NOT connect Dim to the output V or V+, otherwise the driver will not work properly. 3. If 05V dimming is not used, Dim + should be open. 4. When 05V negative logic dimming mode and Dim+ is open, the driver will output maximum current. 010V Dimming The recommended implementation of the dimming control is provided below. Implementation 3: Positive logic 7 / 11 Tel: Fax: sales@inventronicsco.com

8 EBD150SxxxDVA Implementation 4: Negative logic Notes: 1. The dimmer can also be replaced by an active 010V voltage source signal or passive components like resistors and zener. 2. Do NOT connect Dim to the output V or V+, otherwise the driver will not work properly. 3. If 010V dimming is not used, Dim + should be open. 4. When 010V negative logic dimming mode and Dim+ is open, the driver will output minimum current. PWM Dimming Implementation 5: Positive logic Implementation 6: Negative logic 8 / 11 Tel: Fax: sales@inventronicsco.com

9 EBD150SxxxDVA Notes: 1. Do NOT connect Dim to the output V or V+, otherwise the driver will not work properly. 2. If PWM dimming is not used, Dim + should be open. 3. When PWM negative logic dimming mode and Dim+ is open, the driver will output minimum current. Time Dimming Set the timing curve by pulling the sliders. 9 / 11 Tel: Fax: sales@inventronicsco.com

10 EBD150SxxxDVA Programming Connection Diagram Note: The driver does not need to be powered on during the programming process. Please refer to PRGMUL2 MultiProgrammer datasheet for details. Mechanical Outline AC INPUT (VDE H05RNF 3*1.0mm2) DIMMING WIRES (VDE 3*0.5mm2) BROWN(ACL) BLUE (ACN) YELLOW/GREEN (GND) BROWN(V+) BLUE (V) GRAY PURPLE BLACK/WHITE Tc DC OUTPUT (VDE H05RNF 2*1.0mm2) PROJ: Unspecified tolerance:±1 Note: Waterproof connectors certified to CCC & CE are also available for these drivers; please contact Inventronics Sales. RoHS Compliance Our products comply with the European Directive 2011/65/EC, calling for the elimination of lead and other hazardous substances from electronic products. 10 / 11 Tel: Fax: sales@inventronicsco.com

11 EBD150SxxxDVA Revision History Change Date Rev. Description of Change Item From To A Datasheets Release / / B KS / Added Input surge protection / Updated General Specifications With mounting ear Added C General Specifications Net Weight Updated Safety &EMC Compliance / Updated Mechanical Outline / Updated 11 / 11 Tel: Fax: sales@inventronicsco.com